Controls Integration in Existing Facilities · Controls Integration in Existing Facilities Advance Lighting Controls Omar A. Rivera LC CLEP. SVP Product Development. Orion Lighting

Tampa Convention Center • Tampa, Florida

Controls Integration in Existing Facilities

Advance Lighting Controls

Omar A. Rivera LC CLEPSVP Product Development

Orion LightingAugust 15, 2017

Energy Exchange: Connect • Collaborate • Conserve2

The Rivera’s Military Service Contribution 73 Years

Manuel A Rivera US ArmyManuel A. Rivera Jr. US Air ForceOmar A. Rivera US Air ForceRicardo A. Rivera US Army Force


Orion Lighting & Energy Systems Manufacturing and Education Facilities in Manitowoc Wisconsin

Energy Exchange: Connect • Collaborate • Conserve

• Technology Advancements – Paradigm Shift– Traditional Lighting being replace with LED Lighting– Transition from Analog to Digital Technology– Core & Coil Ballast to Circuit Board Driver– Digital power supplies opened doors to other digital

technology• Wireless • Geo location• Metering• Temperature measurement• Various digital protocols and signals• More similar to a cell phone that an electrical device

4

Transition from Analog to Digital Lighting Systems


• To add “Controls” you need to run low voltage wires in plenum to lighting fixtures.

• Due to the advent of LED drivers (power supply) are digital. This facilitated wireless technology to be implemented in LED luminaires.

• Two methods to implement wireless luminaires – Wireless Relay Node

– Wireless Sensor

5

Conceived Barriers of Adding Controls


• Wireless Relay Node– Relay Node antenna sends wireless signal.– Signal does NOT penetrate metal

• Therefore node must be installed outside fixture– Signal does penetrate ceiling tile– Installs on back or end cap knock out of LED fixture – In existing facilities you would need to access plenum

– If you want to stay away from accessing plenum– This solution is not for you.

6

How Does Wireless Node Work?

Fixture Housing

Retrofit Kit


• Wireless Sensor– Sensor installs on fixture housing facing room.– Wireless signal is not impeded.– Sensor installs at factory, only power connection need.– Sensor added feature for fixture level data collection.– Existing troffer retrofit kits install without having to

access to plenum ideal for existing facilities

7

How Does Wireless Sensor Work?


• Replacement of Fluorescent Fixture will be difficult• Various retrofit kit are available to facilitate conversion from

Fluorescent to LED technology

• 5 easy steps to replace existing Fluorescent Fixture with LED

8



• Sensor & Controls “Beyond Office Applications”.• Sensors are now available wirelessly for:

• High Bays

• Harsh Environments

• Outdoor Applications

9



• Wireless Network Q & A– Q: Is there a way to grow into a Digital Wireless

Network in stages.– A: The answer is yes!– Q: Do all systems allow for gradual growth– A: No some systems require a “Gateway Network”.

10

Conceived barrier of adding controls

Start with 1 floor

Grow to Entire Facility


• Minimize field time installations of Controls & Sensors.• Opt for factory installed. • Fixture will cost more initially, but installation labor cost is reduced

dramatically over all cost is lower.• Factory personal are experts at installing due to volume• Product is pre-tested to function before shipped.• Field installer may be new to sensor wiring which will impact

installation time. Higher potential rate for error adding to trouble shooting time.

• Having sensors installed at factory is covered by Warranty.

11

Budget Versus Hidden Cost


• Require that LED drivers to have 12v auxiliary ports to power LED fixture Senor. This reduces cost of adding power controller a $25 to $30 adder per fixture. (Some special exceptions apply such as high voltage of 480v or emergency battery back up)

12



• Minimize products that require assembly on the job site

13


Fully Assembled “Out of Box” Wireless Sensor factory

installed

0components per each kitto assemble

GOOD BETTER IDEAL


• Select “Job Site Ready Bulk Packaging” over single pack.• Ever try to get pallet through a “Door or Elevator”.

14

Budget versus hidden cost

Been their done that! Boxes label with location 30” Width Boxes Fits Through Doors Fits Through Elevators Can be carried up steps Less time to unpack fixtures Less boxes to recycle Use boxes to remove debris


• Origin of the “Change Order”!• Select a company that has experience professional

pool of “Facility Auditors” .• Avoid the hand off , things get lost in the process.

15



Possibilities of Controls System



2018

20192020

2017Prediction of when solutions will be have been vetted out!



Trend movement from Outdoor to Indoor


Why does “Lighting fixtures” facilitate Data Collection?


Possibilities of Controls SystemMoving into the Cloud, as

security concerns are addressed



Privacy Security

InLight Beam

Pulse modulation transmit a digit of 0 & 1 ‘s by LED sends signal to smart deviceLifi also know as VLC –Visual Light Communication


How does the different wireless protocols topography work

Future Band Width


Protocols and Topography

Common Wireless Network topography Or variation of itKnow as Proprietary

Newer Wireless Network topography In early stages of

implementation


High Level: LED Lighting Gateway Wireless Network

Options:Local serverSeparate Controls Server

Sample Wireless Network Topography Vary Between Vendors


Complete Facility Migration to Smart Sensor Technology

Integration of Building Functions into one System

Harvesting Build Data with view via smart remote devices


• Omar A. Rivera• Orion Energy Systems / Orion Lighting• www.orionlighting.com• SVP Product Development• Orion Lighting• 904 380 5041

• Booth 209

26

Thank You

Documents

Controls Integration in Existing Facilities · Controls Integration in Existing Facilities Advance Lighting Controls Omar A. Rivera LC CLEP. SVP Product Development. Orion Lighting