Control Valve Products for HVAC / BAC - Apex …apexsolutionsmn.com/wp-content/uploads/2015/10/HVACBAC-3...Control Valve Products for HVAC / BAC (Heating, Ventilation, and Air Conditioning

2600 EMRICK BLVD • BETHLEHEM, PA 18020 • USA •800-922-0085 • WWW.WARRENCONTROLS.COMDEPENDABLE, RUGGED, PRECISION CONTROL VALVES AND ACCESSORIES

HV

AC

/B

AC

Control Valve Products for

HVAC / BAC (Heating, Ventilation, and Air Conditioning / Building Automation Control)

ELEC

TRIC

2600 Emrick Blvd • Bethlehem, PA 18020 • USA • 800-922-0085 • www.warrencontrols.com2

A CONFIGURATION is a control valve formed by the combination of a valve and actuator. Configurations are tabulated by valve capacity (Cv), pipe size, end connection, trim material, actuator size, control characteristic, and shut-off capability (differential pressure). To order a control valve configuration, locate the line that best meets your application, and specify the appropriate valve code and actuator code. See the example on this page.

Identifies an ANSI 250, NPT threaded bronze valve body assembly with stainless steel trim and a flow capacity rating (Cv) of 7.2. With Electric Actuator Fail Last Position.

Note: You may also specify on an order available control signals and/or control actions other than the factory settings.

VA2005AC-E024

HOW TO ORDER YOUR CONTROL VALVE

u IDENTIFYING A CONTROL VALVE CONFIGURATION

Fail Last PositionACTUATOR CODE E024

CvSize (IN)

Thd NPT Trim Valve Code

SHUT-OFF Max Timing (SEC)CL III CL IV Motor

4.9 0.5 250 S/S VA2004AC 400 400 907.2 0.75 250 S/S VA2005AC 400 400 9010 1 250 S/S VA2006AC 283 247 90

22.2 1.25 250 S/S VA2007AC 120 96 9024 1.5 250 S/S VA2008AC 120 96 9040 2 250 S/S VA2009AC 70 52 90

VA2005AC

E024

NEW ELECTRIC ACTUATORS

Actuator Code

Travel Inches

Force (Lbs)

Failure Mode

E024 0.875 337 Last PositionE025 0.875 337 Fail safeE026 1.25 450 Fail safeE029 1.5 1011 Last PositionE030 1.5 1011 Fail safe

DISCONTINUED ELECTRIC MOTOR ACTUATORS

MP361CP9302AV330

MP371CP9302AV330

MP381CP9302AV330

MP361CP9302AV352

MP371CP9302AV352

MP381CP9302AV352

VM-1500

VM-1500w/VMS-25

VM-5000

VM-5000w/VMS-25

E002 E017 E000 E001 E016

E006 E007 E016 E008 E019

E018

For 120V Applications refer to Warren Controls AmurAct or other Industrial Valve Products

u DETERMINING BODY MATERIAL CONFIGURATIONMatching the valve’s body material and end connection to existing piping or specifications is the best choice. Otherwise, to determine what body material and end connection you need, you must first know the pressure and temperature of the medium entering your valve. For most flowing media you will need an approximate idea of the temperature. For saturated steam you can use the steam table below to determine the temperature. Once you know the pressure and temperature, you can use the body pressure-temperature rating table, (below, to determine what body material and end connection you need.

EXAMPLE 1: You need a 2-1/2 inch single-seated valve. You have saturated steam entering your valve at 50 PSIG. From the steam table you see the steam has a temperature of 297.7°F. From the valve configuration sheets you know that a 2-1/2 inch single-seated valve is available with an iron body with a 125 flange or an iron body with a 250 flange. Scanning the pressure-temperature rating table, you see that the pressure rating for an iron body with a 125 flange at 297.7°F is not listed but a pressure rating is listed at 300°F. At 300°F the pressure rating is 140 PSIG. Since 300°F exceeds the actual temperature of 297.7°F and the 125 PSIG rating at 300°F exceeds the actual pressure of 50 PSIG, an iron body with a 125 flange is ok.

EXAMPLE 2: You need a 6 inch double-seated valve. You have 200 PSIG water entering your valve at 175°F. From the valve configuration sheets you know that a 6 inch double seated valve is available with an iron body with a 125 flange or an iron body with a 250 flange. Scanning the pressure-temperature rating table, you see that the pressure rating for an iron body with a 125 flange at 175°F is 170 PSIG. Since this pressure rating is less than the actual pressure of 200 PSIG, an iron body with a 125 flange is not ok. Scanning the pressure-temperature rating table again, you see that the pressure rating for an iron body with a 250 flange at 175°F is 385 PSIG. Since this 385 PSIG rating is greater than the actual pressure of 200 PSIG, an iron body with a 250 flange is ok.

Body Pressure-Temperature Ratings (PSIG)

Temp (0F)Brz Body

ThrdIron Body

125 FlgIron Body

Thrd/250 Flg +32 to 100°F 400 175 400

150°F 400 175 400175°F 392 170 385200°F 385 165 370225°F 375 155 355250°F 365 150 340275°F 350 145 325300°F 335 140 310

Saturated Steam Temperature

Pressure (PSIG) Temp (0F)

0 212.02 218.54 224.46 229.88 234.6

10 239.015 249.720 258.8

25 266.830 274.035 280.640 286.745 292.4

50 297.755 302.6

HVAC / BAC HVAC_BAC_ELEC_NoRev_0214 3

TABLE OF CONTENTS

Control Valve Products for HVAC/BACSpecifying and buying a control valve begins with an understanding of the control and piping systems to which it will be connected. The Warren Controls staff has attempted to make the ordering process “user friendly” by placing products into well-defined categories and tabulating information like pipe size, body and trim materials, and flow capacity factors (Cv), followed by an assortment of actuators … a lot of information, in a logical format, intended to make your work as easy as possible.

How to order your Control Valve .................................................................................................................... 2

Electrically Motor-Actuated Valve Configuration Sheets ..................................................................... 4--21

Single-Seated Bronze 1/2 Thru 2 inch ....................................................................................................... 4-5

Single-Seated Iron 2- 1/2 Thru 4 inch ......................................................................................................... 6-7

Single-Seated Cylinder Balanced Iron 2-1/2 Thru 6 inch .................................................................. 8-10

Double-Seated Iron 2-1/2 Thru 10 inch ..................................................................................................... 11-13

3-Way Mixing Bronze 1/2 Thru 2 inch ....................................................................................................... 14-15

3-Way Mixing Iron 2-1/2 Thru 6 inch .......................................................................................................... 16-18

3-Way Diverting (Bronze 1 Thru 2 inch; Iron 2-1/2 Thru 6 inch) .................................................. 19-21

Actuator Wiring Diagrams ............................................................................................................................... 22

VMS 35 Actuator Product Sheet .................................................................................................................. 23

Terms & Conditions ............................................................................................................................................. 24-25

(800) 922-0085 or (610) 317-0800 Mon-Fri: 8:30 AM - 5:00 PM EST

[email protected]

Customer Service Technical Support

2600 Emrick Blvd • Bethlehem, PA 18020 • USA • 800-922-0085 • www.warrencontrols.com

ELECTRICALLY ACTUATED

4 5

SINGLE SEATED BRONZE - 1/2” - 2”

u APPLICATION:Control of Saturated Steam; Water; Water & Glycol Solutions. Seat Leakage Class ANSI III & IV.

u VALVE CONSTRUCTION:

Body: ANSI B16.15 Bronze 250lb.Threaded (NPT) Trim: EQ%, 316 Series Stainless Steel Stem: 316 Stainless Steel Bonnet: Brass / Bronze Packing: TFE V-Ring, 300ºF Max Standard packing / trim constructions are listed above. For water service, EPDM Lip packing

is best. For steam service, TFE V-Ring packing is best. If you wish to have a different packing/ trim combination than the WCI standard to better suit your service, this can be called out on the PO for no additional charge.

u TRIM LIMITS (Flowing Differential Pressure):

S/S Trim: Liquid to 100 PSID Steam to 50 PSID

u ACTUATOR SPECIFICATIONS: Control Signal: 2-10 Vdc (4-20 mAdc with 500 ohm resistor Kit KR500-supplied with motor) Control Action, Loss of Signal: Increasing Signal Opens Valve, Loss of Signal Closes Valve (Default Setting) Reversible with Switch. Can be specified when ordering. Feedback Signal: 2-10 Vdc

Power Supply: 24 VAC/DC

Loss of Power: E024 &E029 (FAIL LAST POSITION)

E030 (E029 w/ VMS-35 BCM, FAIL SAFE TO LOSS OF SIGNAL POSITION)

E025 &E026 (ELECTRONIC FAIL SAFE) Fail Closed (Default Setting) Reversible with Switch. Can be specified when ordering.

Power Consumption Running: E024 4W; E025 8.5W; E026 12W; E029/E030 6W

Holding: E024 2.5W; E025 2.5W; E026 3W; E029/E030 3.5W

Timing: See Configuration Tables Manual Override: Hex crank (supplied with actuator) Construction: Aluminum Die Cast and Plastic Housing Locations: NEMA Type 2 / IP54, UL enclosure type 2 Temperature Limits: +32oF to 122oF Ambient Mounting: Vertical above centerline of valve Safety Agency Listing: CE , cUL pending

u VMS-35 BCM SPECIFICATIONS:Required for Fail Safe Operation with fail last position (Actuators E024 & E029)(one VMS-35 can operate two actuators at a time) The E030 includes a VMS-35 BCM. Fail Direction: Field Selectable to Close or Open Valve on Loss of Power Power Consumption: 24VAC, 40VA Construction: Battery w/Circuit Board & Transformer in the Nema 4x Enclosure Mounting: Wall Mount Dimensions: 8.75” (W) x 6.97” (H) x 5.19” (D) (See page 23)

VA2007AC-E025

VA2009AC-E029

NOTES:1) Inlet Pressure cannot exceed Body

Pressure-Temperature Rating.2) Shut-off pressures listed are with

respect to stated ANSI Leakage Classes.

3) Flowing PSID for water service should be no greater than 2/3 of Inlet Pressure unless verified for absence of cavitation with Warren Valve Sizing Program.

HVAC / BAC HVAC_BAC_ELEC_NoRev_0214


4 5

SINGLE SEATED BRONZE - 1/2” - 2”

ITEM WEIGHT

VALVE LBS1/2, 3/4, 1 8-1/2

1-1/4 & 1-1/2 14-1/22 18-1/2

ACTUATOR LBSE024 3-1/2E025 4E026 8-1/2

E029/E030 8BCM LBS

VMS-35 4-1/2

Actual shipping weights may vary.

u ACTUATOR & VALVE CONFIGURATIONS: Select Valve & Actuator Code in Tables:


CvSize (IN)





Fail SafeACTUATOR CODE E025

CvSize (IN)


SHUT-OFF Max Timing (SEC)CL III CL IV Motor Fail Safe

4.9 0.5 250 S/S VA2004AC 400 400 90 357.2 0.75 250 S/S VA2005AC 400 400 90 3510 1 250 S/S VA2006AC 283 247 90 35

22.2 1.25 250 S/S VA2007AC 120 96 90 3524 1.5 250 S/S VA2008AC 120 96 90 3540 2 250 S/S VA2009AC 70 52 90 35


CvSize (IN)



10 1 250 S/S VA2006AC 395 360 90 3522.2 1.25 250 S/S VA2007AC 171 147 90 3524 1.5 250 S/S VA2008AC 171 147 90 3540 2 250 S/S VA2009AC 102 83 90 35

Fail Last Position/ Fail SafeACTUATOR CODE E029/EO30

CvSize (IN)


Fail Last Position (Actuator Code)

Fail Safe w/VMS35 (Actuator Code)


22.2 1.25 250 S/S VA2007AC E029 E030 400 400 9024 1.5 250 S/S VA2008AC E029 E030 400 400 9040 2 250 S/S VA2009AC E029 E030 260 242 90

u Dimensions (IN):

Component Dimension by Valve Size (IN)

Variable 1/2 & 3/4 1 1-1/4 & 1-1/2 2A 250THD 4-7/8 4-7/8 5-3/4 6-1/2B 2-3/4 2-3/4 3-1/4 3-5/8C E024 11-7/8 11-7/8 12-1/2 12-3/4C E025 12-5/8 12-5/8 13-1/4 13-1/2C E026/ E029/E030 N/A 15-1/4 15-7/8 16-1/2H E024 14-5/8 14-5/8 15-3/4 16-3/8H E025 15-3/8 15-3/8 16-1/2 17-1/4H E026/ E029/E030 N/A 20-1/4 19-1/4 20-1/4R E024/E029/E030 7-1/2 7-1/2 7-1/2 7-1/2R E025/E026 8-3/4 8-3/4 8-3/4 8-3/4

TEMP. 250 THD (RATINGS ARE PSIG)

+32 to 150º F 400300º F 335

Pressure boundary meets ANSI B16.15

WEIGHTS

ACTUATED ASSEMBLY BODY PRESSURE

TEMPERATURE RATINGS

Allow 6 inch clearance above actuator for removal / service.

*Center line of Valve to Outside Actuator

A

C

BVALVE

ELEC.Motor

H

R



6 7

SINGLE SEATED IRON - 2 1/2” - 4”

u APPLICATION:Control of Saturated Steam; Water; Water & Glycol Solutions to 60%. Seat Leakage Class ANSI III & IV.


Body: ANSI B16.1 Iron 125lb. Flange or 250lb. Flange Trim: EQ%, Bronze or 300 Series Stainless Steel Stem: 316 Stainless Steel Bonnet: Brass Packing: EPDM Lip Packing (Bronze Trim), 300OF Max TFE V-Ring (Stainless Steel Trim), 300OF Max Standard packing / trim constructions are listed above. For water service, EPDM Lip packing



Brz Trim: Liquid or Steam to 40 PSID S/S Trim: Liquid or to 100 PSID Steam to 50 PSID

u ACTUATOR SPECIFICATIONS:

Control Signal: 2-10 Vdc (4-20 mAdc with 500 ohm resistor Kit KR500-supplied with motor) Control Action, Loss of Signal: Increasing Signal Opens Valve, Loss of Signal Closes Valve (Default Setting) Reversible with Switch. Can be specified when ordering. Feedback Signal: 2-10 Vdc


Loss of Power: E029 (FAIL LAST POSITION)


E026 (ELECTRONIC FAIL SAFE) Fail Closed (Default Setting) Reversible with Switch. Can be specified when ordering.

Power Consumption Running: E026 12W; E029/E030 6W

Holding: E026 3W; E029/E030 3.5W


u VMS-35 BCM SPECIFICATIONS:Required for Fail Safe Operation with fail last position (Actuators E024 & E029)(one VMS-35 can operate two actuators at a time) The E030 includes a VMS-35 BCM. Fail Direction: Field Selectable to Close or Open Valve on Loss of Power Power Consumption: 24VAC, 40VA Construction: Battery w/Circuit Board & Transformer in the Nema 4x Enclosure Dimensions: 8.75” (W) x 6.97” (H) x 5.19” (D) (See page 23)

VA2010CC-E026

VA2013CC-E029







6 7

SINGLE SEATED IRON - 2 1/2” - 4”



CvSize (IN) FLNG Trim Valve Code


65 2.5 125 BRZ VA2010CA 71 55 90 3565 2.5 125 S/S VA2010CC 71 55 90 3565 2.5 250 BRZ VA2010DA 71 55 90 3565 2.5 250 S/S VA2010DC 71 55 90 3590 3 125 BRZ VA2011CA 47 34 90 3590 3 125 S/S VA2011CC 47 34 90 3590 3 250 BRZ VA2011DA 47 34 90 3590 3 250 S/S VA2011DC 47 34 90 35



Fail Last Position

(Actuator Code)

Fail Safe w/VMS35 (Actuator

Code)

SHUT-OFFMax Timing

(SEC)

CL III CL IV Motor65 2.5 125 BRZ VA2010CA E029 E030 186 170 9065 2.5 125 S/S VA2010CC E029 E030 186 170 9065 2.5 250 BRZ VA2010DA E029 E030 186 170 9065 2.5 250 S/S VA2010DC E029 E030 186 170 9090 3 125 BRZ VA2011CA E029 E030 127 113 9090 3 125 S/S VA2011CC E029 E030 127 113 9090 3 250 BRZ VA2011DA E029 E030 127 113 9090 3 250 S/S VA2011DC E029 E030 127 113 90

170 4 125 BRZ VA2013CA E029 E030 69 59 90170 4 125 S/S VA2013CC E029 E030 69 59 90170 4 250 BRZ VA2013DA E029 E030 69 59 90170 4 250 S/S VA2013DC E029 E030 69 59 90

u Dimensions (IN):


Variable 2-1/2 3 4A 125 FLG 9 10 13A 250 FLG 9-5/8 10-3/4 13-5/8B 4-3/4 5-3/8 6-3/8C 17-3/4 18-5/8 19-5/8 H 22-1/2 24 26R* E026 8-3/4 8-3/4 8-3/4R* E029 7-1/2 7-1/2 7-1/2


TEMP. 125 FLG 250 FLG

+32 to 150º F 175 400

300º F 140 310


WEIGHTS


TEMPERATURE RATINGS


A

C

BVALVE

ELEC.Motor

H

R

ITEM WEIGHT (LBS)

VALVE 125 FLG 250 FLG

2-1/2 55 643 72 774 119 131

ACTUATOR LBS

E026 8-1/2E029/E030 8

BCM LBS

VMS-35 4-1/2Actual shipping weights may vary.



8

SINGLE SEATED CYLINDER BALANCED IRON - 2 1/2” - 6”

u APPLICATION:Control of Saturated Steam; Water; Water & Glycol Solutions to 60%. Seat Leakage Class ANSI III & IV.


Body: ANSI B16.1 Iron 125lb. Flange or 250lb. Flange

Trim: EQ%, Bronze or 300 Series Stainless Steel Cylinder Seal: EPDM (BRZ Trim) O-Ring Aflas VP101-80 (300 SS Trim) O-Ring Stem: 316 Stainless Steel Bonnet: Brass Packing: EPDM Lip Packing (Bronze Trim), 300OF Max TFE V-Ring (Stainless Steel Trim), 300OF Max Standard packing / trim constructions are listed above. For water service, EPDM Lip packing



Brz Trim: Liquid or Steam to 40 PSID S/S Trim: Liquid to 100 PSID Steam to 50 PSID

u ACTUATOR SPECIFICATIONS: Control Signal: 2-10 Vdc (4-20 mAdc with 500 ohm resistor Kit KR500-supplied with motor) Control Action, Loss of Signal: Increasing Signal Opens Valve, Loss of Signal Closes Valve (Default Setting) Reversible with Switch. Can be specified when ordering. Feedback Signal: 2-10 Vdc


Loss of Power: E024 &E029 (FAIL LAST POSITION)


E025 &E026 (ELECTRONIC FAIL SAFE) Fail Closed (Default Setting) Reversible with Switch. Can be specified when ordering.

Power Consumption Running: E024 4W; E025 8.5W; E026 12W; E029/E030 6W

Holding: E024 2.5W; E025 2.5W; E026 3W; E029/E030 3.5W



VA2310CA-E025

VA2315CA-E029







9





SHUT-OFFMax Timing

(SEC)CL III CL IV Motor

65 2.5 125 BRZ VA2310CA 175 175 9065 2.5 125 S/S VA2310CC 175 175 9065 2.5 250 BRZ VA2310DA 358 226 9065 2.5 250 S/S VA2310DC 358 226 9090 3 125 BRZ VA2311CA 175 140 9090 3 125 S/S VA2311CC 175 140 9090 3 250 BRZ VA2311DA 275 140 9040 3 250 S/S VA2311DC 275 140 90









170 4 125 BRZ VA2313CA 175 141 90 35170 4 125 S/S VA2313CC 175 141 90 35170 4 250 BRZ VA2313DA 281 141 90 35170 4 250 S/S VA2313DC 281 141 90 35260 5 125 BRZ VA2314CA 175 46 90 35260 5 125 S/S VA2314CC 175 46 90 35260 5 250 BRZ VA2314DA 187 46 90 35260 5 250 S/S VA2314DC 187 46 90 35

10 112600 Emrick Blvd • Bethlehem, PA 18020 • USA • 800-922-0085 • www.warrencontrols.com


10


TEMP. 150 THD (PSIG)

250 THD (PSIG)

+32 to 150º F 175 400

350º F 125 280


WEIGHTS


TEMPERATURE RATINGS

ITEM WEIGHT (LBS)


2-1/2 55 663 75 804 127 1395 149 1816 197 256

ACTUATOR LBS

E024 3-1/2E025 4E026 8-1/2

E029/E030 8BCM LBS




A

C

BVALVE

ELEC.Motor

H

R




Fail Last Position

(Actuator Code)

Fail Safe w/VMS35 (Actuator

Code)SHUT-OFF

Max Timing


170 4 125 BRZ VA2313CA E029 E030 175 175 90170 4 125 S/S VA2313CC E029 E030 175 175 90170 4 250 BRZ VA2313DA E029 E030 400 400 90170 4 250 S/S VA2313DC E029 E030 400 400 90280 5 125 BRZ VA2314CA E029 E030 175 175 90280 5 125 S/S VA2314CC E029 E030 175 175 90280 5 250 BRZ VA2314DA E029 E030 400 400 90280 5 250 S/S VA2314DC E029 E030 400 400 90360 6 125 BRZ VA2315CA E029 E030 175 175 90360 6 125 S/S VA2315CC E029 E030 175 175 90360 6 250 BRZ VA2315DA E029 E030 400 400 90360 6 250 S/S VA2315DC E029 E030 400 400 90

u Dimensions (IN):


Variable 2-1/2 3 4 5 6A 125 FLG 9 10 13 15-3/4 17-3/4A 250 FLG 9-5/8 10-3/4 13-5/8 16-5/8 18-5/8B 4-3/4 5-3/8 6-3/8 5-3/4 6-1/2C E024 14-3/8 15-1/4 16-3/8 16-7/8 17-1/2C E025 14-5/8 15-7/8 17 17-1/2 18-1/8C E026/E029/E030 18-1/4 19-1/8 20-1/4 20-3/4 21-3/8H E024 19-1/8 20-5/8 22-3/4 22-5/8 24H E025 19-3/4 21-1/4 23-3/8 22-1/4 24-5/8H E026/E029/E030 23 24-1/2 26-5/8 25-1/2 27-7/8R* E024/E029/E030 7-1/2 7-1/2 7-1/2 7-1/2 7-1/2R* E025/E026 8-3/4 8-3/4 8-3/4 8-3/4 8-3/4

CYLINDER SEAL TEMPERATURE LIMITS

+32 to 300º F



10 11

DOUBLE SEATED IRON - 2 1/2” - 10”

u APPLICATION:Control of Saturated Steam; Water; Water & Glycol Solutions to 60%. Seat Leakage ANSI Class III.


Body: ANSI B16.1 Iron 125lb. Flange or 250lb. Flange Trim: EQ%, Bronze or 300 Series Stainless Steel Stem: 316 Stainless Steel Bonnet: Brass Packing: EPDM Lip Packing (Bronze Trim), 300OF Max TFE V-Ring (Stainless Steel Trim), 300OF Max Standard packing / trim constructions are listed above. For water service, EPDM Lip packing



Brz Trim: Liquid or Steam to 40 PSID S/S Trim: Liquid to 100 PSID Steam to 50 PSID


Control Signal: 2-10 Vdc (4-20 mAdc with 500 ohm resistor Kit KR500-supplied with motor) Control Action, Loss of Signal: Increasing Signal Opens Valve, Loss of Signal Closes Valve (Default Setting) Reversible with Switch. Can be specified when ordering. Feedback Signal: 2-10 Vdc


Loss of Power: E029 (FAIL LAST POSITION)


E025 & E026 (ELECTRONIC FAIL SAFE) Fail Closed (Default Setting) Reversible with Switch. Can be specified when ordering.

Power Consumption Running: E025 8.5W; E026 12W; E029/E030 6W

Holding: E025 2.5W; E026 3W; E029/E030 3.5W



VA2213CA-E025

VA2215CC-E029







12 13




SHUT-OFF(PSID)

Max Timing (SEC)Motor Fail Safe

70 2.5 125 BRZ VA2210CA 175 90 3570 2.5 125 S/S VA2210CC 175 90 3570 2.5 250 BRZ VA2210DA 400 90 3570 2.5 250 S/S VA2210DC 400 90 35

100 3 125 BRZ VA2211CA 175 90 35100 3 125 S/S VA2211CC 175 90 35100 3 250 BRZ VA2211DA 400 90 35100 3 250 S/S VA2211DC 400 90 35200 4 125 BRZ VA2213CA 175 90 35200 4 125 S/S VA2213CC 175 90 35200 4 250 BRZ VA2213DA 223 90 35200 4 250 S/S VA2213DC 223 90 35



SHUT-OFF(PSID)

Max Timing (SEC)Motor Fail Safe

200 4 125 BRZ VA2213CA 175 90 35200 4 125 S/S VA2213CC 175 90 35200 4 250 BRZ VA2213DA 400 90 35200 4 250 S/S VA2213DC 400 90 35260 5 125 BRZ VA2214CA 175 90 35260 5 125 S/S VA2214CC 175 90 35260 5 250 BRZ VA2214DA 287 90 35260 5 250 S/S VA2214DC 287 90 35350 6 125 BRZ VA2215CA 175 90 35350 6 125 S/S VA2215CC 175 90 35350 6 250 BRZ VA2215DA 197 90 35350 6 250 S/S VA2215DC 197 90 35





SHUT-OFF(PSID)

Max Timing (SEC)

Motor350 6 125 BRZ VA2215CA E029 E030 175 90350 6 125 S/S VA2215CC E029 E030 175 90350 6 250 BRZ VA2215DA E029 E030 400 90350 6 250 S/S VA2215DC E029 E030 400 90680 8 125 BRZ VA2217CA E029 E030 175 90680 8 125 S/S VA2217CC E029 E030 175 90680 8 250 BRZ VA2217DA E029 E030 400 90680 8 250 S/S VA2217DC E029 E030 400 90960 10 125 BRZ VA2219CA E029 E030 175 90960 10 125 S/S VA2219CC E029 E030 175 90960 10 250 BRZ VA2219DA E029 E030 392 90960 10 250 S/S VA2219DC E029 E030 392 90




12 13


u Dimensions (IN):


Variable 2-1/2 3 4 5 6 8 10A 125 FLG 7-3/4 9 11-3/8 12 14-1/8 16-1/4 20A 250 FLG 8-3/8 9-3/4 12 12-7/8 14-1/2 16-1/4 21-3/8B 4-1/8 4-3/8 5 6-7/8 7-5/8 8-7/8 9-7/8C E025 14-1/8 14-3/8 15-7/8 - - - -C E026/E029/E030 17-3/8 17-5/8 19-1/8 20-1/8 21 22-1/8 22-7/8H E025 18-1/4 18-3/4 20-7/8 - - - -H E026/E029/E030 21-1/2 22 24-1/8 27 28-5/8 31 32-3/4R* E029/E030 7-1/2 7-1/2 7-1/2 7-1/2 7-1/2 7-1/2 7-1/2R* E025/E026 8-3/4 8-3/4 8-3/4 8-3/4 8-3/4 8-3/4 8-3/4



A

C

BVALVE

ELEC.Motor

H

RITEM WEIGHT (LBS)


2-1/2 32 423 42 544 77 965 124 1626 169 2208 290 380

10 435 540ACTUATOR LBS

E025 4E026 8-1/2

E029/E030 8BCM LBS


TEMP. 125 FLG (PSIG)

250 FLG (PSIG)

+32 to 150º F 175 400

300º F 140 310


WEIGHTS


TEMPERATURE RATINGS



14 15

3-WAY MIXING BRONZE - 1/2” - 2”

u APPLICATION:Control of Saturated Steam; Water; Water & Glycol Solutions. Seat Leakage Class ANSI III & IV.


Body: ANSI B16.15 Bronze 250lb.Threaded (NPT) Trim: Linear, 316 Series Stainless Steel Stem: 316 Stainless Steel Bonnet: Brass / Bronze Packing: TFE V-Ring, 300ºF Max Standard packing / trim constructions are listed above. For water service, EPDM Lip packing



S/S Trim: Liquid to 100 PSID Steam to 50 PSID


Control Signal: 2-10 Vdc (4-20 mAdc with 500 ohm resistor Kit KR500-supplied with motor) Control Action, Loss of Signal: Increasing Signal Opens Lower Port/ Closes Upper Port, Loss of Signal Closes Lower Port/ Opens Upper Port (Default Setting) Reversible with Switch. Can be specified when ordering. Feedback Signal: 2-10 Vdc

Power Supply: 24 VAC/DC Loss of Power: E024 & E029 (FAIL LAST POSITION)


E025 & E026 (ELECTRONIC FAIL SAFE) Fail Lower Port Closed/ Upper Port Open (Default Setting) Reversible with Switch. Can be specified when ordering.

Power Consumption Running: E024 4W; E025 8.5W; E026 12W; E029/E030 6W Holding: E024 2.5W; E025 2.5W; E026 3W; E029/E030 3.5W



VA3008AC-E025

VA3009AC-E029







14 15

3-WAY MIXING BRONZE - 1/2” - 2”

ITEM WEIGHT

VALVE LBS1/2, 3/4, 1 9

1-1/4 & 1-1/2 15-1/22 20

ACTUATOR LBSE024 3-1/2E025 4E026 8-1/2

E029/E030 8BCM LBS

VMS-35 4-1/2

Actual shipping weights may vary.



CvSize (IN)






CvSize (IN)



6.3 0.5 250 S/S VA3004AC 238 203 90 358.2 0.75 250 S/S VA3005AC 238 203 90 3510 1 250 S/S VA3006AC 238 203 90 35

18.5 1.25 250 S/S VA3007AC 100 76 90 3520 1.5 250 S/S VA3008AC 100 76 90 3540 2 250 S/S VA3009AC 58 39 90 35


CvSize (IN)



10 1 250 S/S VA3006AC 351 315 90 3518.5 1.25 250 S/S VA3007AC 151 127 90 3520 1.5 250 S/S VA3008AC 151 127 90 3540 2 250 S/S VA3009AC 90 71 90 35


CvSize (IN)





18.5 1.25 250 S/S VA3007AC E029 E030 400 381 9020 1.5 250 S/S VA3008AC E029 E030 400 381 9040 2 250 S/S VA3009AC E029 E030 248 229 90

u Dimensions (IN):


Variable 1/2 & 3/4 1 1-1/4 1-1/2 2A 4-7/8 4-7/8 5-3/4 5-3/4 6-1/2B 2-23/32 2-23/32 3-13/16 3-13/16 4C E024 11-1/2 11-1/2 12-1/8 12-1/8 12-3/8C E025 12-1/8 12-1/8 12-3/4 12-3/4 13C E026/E029/E030 15-3/8 16 16 16-1/4H E024 14-7/32 14-7/32 15-15/16 15-15/16 16-3/8H E025 14-27/32 14-27/32 15-9/16 15-9/16 17H E026/E029/E030 18-3/32 18-13/16 18-13/16 20-1/4R* E024/E029/E030 7-1/2 7-1/2 7-1/2 7-1/2 7-1/2R* E025/E026 8-3/4 8-3/4 8-3/4 8-3/4 8-3/4


+32 to 150º F 400300º F 335


WEIGHTS


TEMPERATURE RATINGS



A

C

BVALVE

ELEC.Motor

H

R



16 17

3-WAY MIXING IRON - 2 1/2” - 6”

u APPLICATION:Control of Water; Water & Glycol Solutions to 60%. Valves mix two flows together (Converging). Seat Leakage ANSI Class III & IV.


Body: ANSI B16.1 Iron 125lb. Flange or 250lb. Flange Trim: Linear, Bronze or 300 Series Stainless Steel Stem: 316 Stainless Steel Bonnet: Brass Packing: EPDM Lip Packing (Bronze Trim), 300OF Max TFE V-Ring (Stainless Steel Trim), 300OF Max Standard packing / trim constructions are listed above. For water service, EPDM Lip packing



S/S Trim: Liquid to 100 PSID


Control Signal: 2-10 Vdc (4-20 mAdc with 500 ohm resistor Kit KR500-supplied with motor) Control Action, Loss of Signal: Increasing Signal Opens Lower Port/ Closes Upper Port, Loss of Signal Closes Lower Port/ Opens Upper Port (Default Setting) Reversible with Switch. Can be specified when ordering. Feedback Signal: 2-10 Vdc







VA3008AC-E025

VA3009AC-E029







16 17



















SHUT-OFFMax Timing


156 4 125 BRZ VA3013CA E029 E030 65 55 90156 4 125 S/S VA3013CC E029 E030 65 55 90156 4 250 BRZ VA3013DA E029 E030 65 55 90156 4 250 S/S VA3013DC E029 E030 65 55 90270 5 125 BRZ VA3014CA E029 E030 40 32 90270 5 125 S/S VA3014CC E029 E030 40 32 90270 5 250 BRZ VA3014DA E029 E030 40 32 90270 5 250 S/S VA3014DC E029 E030 40 32 90347 6 125 BRZ VA3015CA E029 E030 27 20 90347 6 125 S/S VA3015CC E029 E030 27 20 90347 6 250 BRZ VA3015DA E029 E030 27 20 90347 6 250 S/S VA3015DC E029 E030 27 20 90



18 19




A

C

BVALVE

ELEC.Motor

H

R

u Dimensions (IN):


Variable 2-1/2 3 4 5 6A 125 FLG 9 10 13 15-3/4 17-3/4A 250 FLG 9-5/8 10-3/4 13-5/8 16-5/8 18-5/8B 125 FLG 7-1/16 7-15/16 9-7/8 9-1/4 9-7/8B 250 FLG 7-3/8 8-5/16 10-3/16 10-3/8 11C E024 13-7/8 14-3/4 15-3/4 14-5/8 15-3/8C E025 14-1/2 15-3/8 16-3/8 15-1/4 16C E026/E029/E030 17-3/4 18-5/8 19-5/8 19-1/2 19-1/4H E024 125 FLG 20-15/16 22-11/16 15-5/8 24-7/8 25-1/4H E024 250 FLG 21-1/4 23-11/16 25-15/16 26 26-3/8H E025 125 FLG 21-9/16 23-5/16 16-1/4 25-1/2 25-7/8H E025 250 FLG 21-7/8 24-5/16 26-9/16 26-5/8 27H E026/E029/E030 125 FLG 24-13/16 26-9/16 19-1/2 28-3/8 29-1/8H E026/E029/E030 250 FLG 25-1/8 27-9/16 29-13/16 29-7/8 30-1/4R* E024/E029/E030 7-1/2 7-1/2 7-1/2 7-1/2 7-1/2R* E025/E026 8-3/4 8-3/4 8-3/4 8-3/4 8-3/4

ITEM WEIGHT (LBS)


2-1/2 64 733 83 944 139 1575 157 2116 202 283

ACTUATOR LBS

E024 3-1/2E025 4E026 8-1/2

E029/E030 8BCM LBS



250 FLG (PSIG)

+32 to 150º F 175 400

300º F 140 310


WEIGHTS


TEMPERATURE RATINGS



18 19

3-WAY DIVERTING BRONZE/IRON 1”-6”

u APPLICATION:Control of Saturated Steam; Water; Water & Glycol Solutions. Seat Leakage ANSI Class II.


Body: Size 1, 1-1/2 & 2 inch ANSI B16.15 Bronze 250lb. Threaded (NPT); Size 2-1/2, 3, 4, 5 & 6 inch ANSI B16.1 Iron 125lb. Flange or 250lb Flange Trim: Linear, Bronze or 300 Series Stainless Steel Stem: 316 Stainless Steel Bonnet: Brass Packing: EPDM Lip Packing (Bronze Trim), 300OF Max TFE V-Ring (Stainless Steel Trim), 300OF Max Standard packing / trim constructions are listed above. For water service, EPDM Lip packing


O-Ring: EPR


Brz Trim: Liquids to 40 PSID S/S Trim: Liquids to 100 PSID

u ACTUATOR SPECIFICATIONS: Control Signal: 2-10 Vdc (4-20 mAdc with 500 ohm resistor Kit KR500-supplied with motor) Control Action, Loss of Signal: Increasing Signal Opens Lower Port/ Closes Upper Port, Loss of Signal Closes Lower Port/ Opens Upper Port (Default Setting) Reversible with Switch. Can be specified when ordering. Feedback Signal: 2-10 Vdc







VA3208AA-E025

VA3213CA-E029





4) The difference between the upper port and the lower port pressure must not exceed 50 PSID.



20 21

3-WAY DIVERTING BRONZE/IRON 1”-6”



CvSize (IN)


SHUT-OFFMax Timing

(SEC)PSID Motor

12 1 250 BRZ VA3206AA 125 9022 1.5 250 BRZ VA3208AA 125 9040 2 250 BRZ VA3209AA 125 90


CvSize (IN)


SHUT-OFF Max Timing (SEC)PSID Motor Fail Safe

12 1 250 BRZ VA3206AA 125 90 3522 1.5 250 BRZ VA3208AA 125 90 3540 2 250 BRZ VA3209AA 125 90 35


CvSize (IN)


SHUT-OFF Max Timing (SEC)PSID Motor Fail Safe



CvSize (IN)




SHUT-OFFMax Timing

(SEC)PSID Motor

160 4 125 BRZ VA3213CA E029 E030 125 90160 4 125 S/S VA3213CC E029 E030 125 90160 4 250 BRZ VA3213DA E029 E030 125 90160 4 250 S/S VA3213DC E029 E030 125 90195 5 125 BRZ VA3214CA E029 E030 125 90195 5 125 S/S VA3214CC E029 E030 125 90195 5 250 BRZ VA3214DA E029 E030 125 90195 5 250 S/S VA3214DC E029 E030 125 90270 6 125 BRZ VA3215CA E029 E030 125 90270 6 125 S/S VA3215CC E029 E030 125 90270 6 250 BRZ VA3215DA E029 E030 125 90270 6 250 S/S VA3215DC E029 E030 125 90



20 21



A

C

BVALVE

ELEC.Motor

H

R

u Dimensions (IN):


Variable 1 1-1/2 2A 4-7/8 5-3/4 6-1/2B 3-15/32 3-13/16 4C E024 11-1/2 12-1/8 12-3/8C E025 12-1/8 12-3/4 13H E024 14-31/32 18-3/16 16-3/8H E025 15-19/32 18-13/16 17R* E024 7-1/2 7-1/2 7-1/2R* E025 8-3/4 8-3/4 8-3/4


Variable 2-1/2 3 4 5 6A 125 FLG 9 10 13 12 14-1/8A 250 FLG 9-5/8 10-3/4 13-5/8 12-7/8 14-1/2B 125 FLG 7-1/16 7-15/16 9-7/8 10-1/2 11-1/16B 250 FLG 7-3/8 8-5/16 10-3/16 10-15/16 11-1/2C E024 13-7/8 14-3/4 15-1/2 16-1/8 16-3/4C E025 14-1/2 15-3/8 16-1/8 16-3/4 17-3/8C E026/E029/E030 17-3/4 18-5/8 19-3/8 20 20-5/8H E024 125 FLG 20-15/16 22-11/16 25-3/8 26-5/8 27-13/16H E024 250 FLG 21-1/4 23-1/16 25-11/16 27-1/16 28-1/4H E025 125 FLG 21-9/16 23-5/16 26 27-1/4 28-7/16H E025 250 FLG 21-7/8 23-11/16 26-5/16 27-11/16 28-7/8H E026/E029/E030 125 FLG 24-13/16 26-9/16 29-1/4 30-1/2 31-11/16H E026/E029/E030 250 FLG 25-1/8 26-15/16 29-9/16 30-15/16 32-1/8R* E024/E029/E030 7-1/2 7-1/2 7-1/2 7-1/2 7-1/2R* E025/E026 8-3/4 8-3/4 8-3/4 8-3/4 8-3/4

ITEM WEIGHT (LBS)

VALVE LBS

1 91-1/2 16-1/2

2 21VALVE 125 FLG 250 FLG

2-1/2 59 733 78 944 138 1575 152 2136 203 284

ACTUATOR LBS

E024 3-1/2E025 4E026 8-1/2

E029/E030 8BCM LBS



250 FLG (PSIG)

+32 to 150º F 175 400

300º F 140 310


WEIGHTS

3-WAY DIVERTING BRONZE/IRON 1’-6’


TEMPERATURE RATINGS VALVES: 1”-2”


+32 to 150º F 400300º F 335



TEMPERATURE RATINGS VALVES: 2-1/2”-6”


ACTUATOR WIRING DIAGRAMS

2-10 VDC

Line

Volts24 VAC

CLASS 2TRANSFORMER

2-10 VDC

CONTROLSIGNAL

2-10 VDC

FEED-BACK

ACTUATOR

BK #1 ( )

RD #2 ( )

WH #3 (Y)

OR #5 (U)

Common

Hot

Input, 2 to 10 VDC

Output, 2 to 10 VDC

4-20 MADC

Line

Volts24 VAC

CLASS 2TRANSFORMER

4-20 MADC

CONTROLSIGNAL

2-10 VDC

FEED-BACK

ACTUATOR

BK #1 ( )

RD #2 ( )

WH #3 (Y)

OR #5 (U)

Common

Hot

Input, 2 to 10 VDC

Output, 2 to 10 VDC

KR500RESISTOR


BACK-UP CONTROL MODULEBCM SPECIFICATIONS

Actuator Usage: E030 (E030 includes a VMS-35 BCM), E029, E024Power supply: 24 VAC ± 20% 50/60 HzPower Consumption: 40 VA (add VA rating for actuator used)Number Actuators: One or TwoConstruction: Battery w/Circuit Board, Charger and TransformerEnclosure Type: NEMA 4X, IP66, UL 4X, CSA 4XFlame Retardant: UL 50Construction: UV Stabilized Fiberglass Reinforced Polyester, Polycarbonate Hinge and Closed Cell Neoprene Gasket Connections: Two 1/2 IN conduit with one plugNumber Batteries: OneInitial Charge: 2-4 hoursBattery Life: Up to 5 years … Replacement battery model UB1213 / 12V, 1.3 AhMounting: Feet for Wall Mount (4.91” x 8.75” centers)Environmental: Operating/ Storage: Ambient +32°F to +104°F (0 to +40°C) – due to batteryWeight: 4.25 lbs (2 kg)

VMS-35 WIRING DIAGRAM

TERMINALS

L System Power 24 VAC (+)LN System Neutral (-)RC Remote ControlBT Battery Test (+)TG Test Ground (-)C1 Control Signal 1st Actuator (+)C2 Control Signal 2nd Actuator (+)NC1 Not UsedNC2 Not UsedNO1 Relay Normally Open 1st ActuatorNO2 Relay Normally Open 2nd ActuatorAC 24 VAC Out (+)

Power Failure: Terminal AC changes to 24 V square wave from battery/ inverter. A relay breaks the connection between Terminals C1 and NO1 forcing the actuator to return to the loss of signal position.

Loss of Signal: Terminal AC uses 24VAC building power. The control signal is broken forcing the actuator to return to the loss of signal position.

Operation: Proportional Normal: Terminal L is connected to 24 VAC building power. Terminal LN completes the circuit to BK. Actuator responds to modulating input signal.

Power 24 VAC

HOT

Existing Jumper

L LN RC LN TG BT AC LNNC1 C1 NO1 NC2 C2 NO2

CONTROL SIGNAL (S)

(RECOMMENDED) (RECOMMENDED)

OUTPUT TO ACTUATOR A

OUTPUT TOACTUATOR B

(IF USED)

Actuator BActuator A

1. The VMS-35 can power one (1) or two (2) actuators.

2. Energize 24 VAC before connecting red lead to battery.

3. Also read actuator wiring and setup instructions.

4. To prevent signal interference proper signal wire cable shielding is recommended.

5. When using long wire runs and a 2 – 10 Vdc signal, signal and power cables should be run in separate conduits to avoid interference.N

OTE

S

VMS-35

OR#5(U) WH#3(Y) RD#2(+) BK#1(-) OR#5(U) WH#3(Y) RD#2(+) BK#1(-)

VMS-35 BCM


TERMS & CONDITIONS OF SALE

WARREN CONTROLS INC. (Hereinafter called “Seller”) agrees to supply the equipment covered herein on the following terms and conditions. Additional terms and conditions not covered herein will be accepted only upon mutual agreement in writing.

ORDERS: Contracts and orders are subject to acceptance by the home office of the Seller.

FREIGHT TERMS: All Prices are FOB factory (Bethlehem, PA).

MINIMUM ORDER REQUIREMENT: All orders must have a minimum net value of $400.

PRICES AND DISCOUNTS: All prices and discounts are in accordance with the established price and discount schedules of the Seller, and are subject to change without notice.

PRICE LIST: The price list is not an offer to sell to any person who possesses it, nor to anyone else, the goods listed herein at the prices shown. All prices herein set forth supersede all prior price lists and are subject to change without notice. Warren Controls Incorporated may also, from time to time, discontinue, without notice, the sale of any of the products herein.

TAXES: The amount of any present or future sales, use, occupancy, excise, or other tax, federal, state or local, which the Seller now, or hereafter shall be legally obligated to pay, either on its own behalf or on the behalf of the purchaser or otherwise, with respect to the material covered by this order or contract, shall (unless the prices contained herein are stated expressly to include such tax) be added to such prices and paid by the purchaser. Purchaser agrees to report and pay any such tax directly on any non-exempt transaction, when Seller’s invoices do not indicate such a charge.

REMITTANCES: All invoices shall be due and payable in United States currency, free of exchange, collection, or any other charges, net 30 days, or as otherwise agreed upon and set forth in writing by Seller. Past due invoices are subject to a carrying charge of 1% per month. The purchaser, if so requested, agrees to furnish Seller with all information, including financial statements, necessary to make proper credit appraisal. Refusal to supply such information may cause a quotation to be withdrawn. Quotations for extended periods are subject to change with reasonable notice.

LIABILITY: The buyer shall remain primarily liable for the purchase price and the Seller shall not be obliged to accept any term or condition of payment which will shift liability to a third person not a party to the contract of sale, whether or not such third person is the United States Government, its agents or instrumentalities.

RUSH ORDERS: Expediting is something that we at Warren Controls Incorporated endeavor to accommodate whenever possible but must be requested and promised on a case-by-case basis. Premium freight is not assumed and must be specified on the purchase order.

DISCONTINUANCES OF DELIVERIES: Should the purchaser’s financial responsibility be or become unsatisfactory to the Seller, cash payment or satisfactory security at any time may be demanded by the Seller, and if not furnished to the Seller’s satisfaction, the Seller may at its option discontinue deliveries and charge the purchaser for the sale value of any completed or partly completed articles manufactured pursuant to the order or contract.

PARTIAL SHIPMENTS: Seller reserves the right to make partial shipments from time to time and render invoices therefore, which shall be due and payable as provided in paragraph entitled “Remittances”.

DELAYS: The Seller shall not be liable for any loss, damage, or delay occasioned by any causes beyond the Seller’s control, including, but not limited to governmental actions or orders, embargoes, strikes, differences with workers, fires, floods, accidents, or transportation delays. IN NO EVENT SHALL SELLER BE LIABLE FOR ANY CONSEQUENTIAL OR SPECIAL DAMAGES.

(800) 922-0085 or (610) 317-0800

Monday - Friday: 8:30 AM - 5:00 PM EST

Customer Service Technical Support


TERMS & CONDITIONS OF SALE

WEIGHTS AND DIMENSIONS: Shipping weights and dimensions given in catalogs and drawings are as close to actual as practicable but are not guaranteed. No claims will be allowed because of any discrepancy between actual weights or dimensions of material shipped and listed data in catalog.SHIPPING AND PACKING: All material is carefully packed for shipment and Seller will not be responsible for loss, delay or breakage after having received “in good order” receipts from the transportation company. All claims for breakage, loss, delay and damage should be made to carriers, but Seller will render all possible assistance in securing satisfactory adjustment of such claims. Goods will be shipped by the method and via carrier Seller believes dependable, unless the buyer designates the carrier. Goods held at factory beyond delivery date for convenience of buyer will be invoiced on date of completion and terms of payment will apply as from invoice date. Such goods will be subject to charges for warehousing and other expenses incident to such delay.

REJECTION OF SHIPMENT: If the purchaser is unable or unwilling to accept any shipment, the purchaser shall be liable to the Seller, in addition to any other rights for which the Seller may be entitled, for freight, express, storage, extra cost of handling, and other expenses incurred thereby.

CANCELLATION: All orders are firm and are not subject to cancellation or change in specifications, shipping schedules or other conditions without Seller’s written consent, which will be given only upon agreement to compensate for loss caused by such cancellation or changes.

SHORTAGE CLAIMS: Claims for shortage or incorrect filling of orders must be made within 60 days from date of delivery.

WARRANTY: The Seller warrants that the equipment manufactured by it and covered by this order is free from defects in material and workmanship and, without charge, product found to be defective in material or workmanship will be repaired, or at Seller’s option replaced F.O.B. original point of shipment, if written notice of failure is received by Seller within one (1) year after date of shipment for valve bodies and five (5) years after date of shipment for catalogued HVAC/BAC electric actuators (unless specifically noted elsewhere), provided said product has been properly installed, operated in accordance with the Seller’s instructions, and provided such defects are not due to abuse or decomposition by chemical or galvanic action. THIS EXPRESS WARRANTY IS IN LIEU OF AND EXCLUDES ALL OTHER WARRANTIES, GUARANTEES, OR REPRESENTATIONS, EXPRESS OR IMPLIED. THERE IS NO IMPLIED WARRANTY OF MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE. Seller assumes no responsibility for repairs made on the Seller’s equipment unless done by the Seller’s authorized personnel, or by written authority from the Seller. The Seller makes no guarantee with respect to material not manufactured by it. Seller shall not be liable for consequential damage in case of any failure to meet the conditions of any guarantee or shipping schedule, nor will claims for labor, loss of profits, repairs or other expenses incidental to replacement be allowed. The Seller in connection with the manufacture and sale of its equipment makes no other representation, guarantee or warranty, expressed or implied.

PURCHASER’S REMEDIES: The purchaser’s remedies with respect to equipment manufactured by Seller covered by this order or contract and found to be defective shall be limited exclusively to the right of repair or replacement of such defective equipment. IN NO EVENT SHALL SELLER BE LIABLE FOR CLAIMS (BASED UPON BREACH OF CONTRACT, BREACH OF EXPRESS OR IMPLIED WARRANTY, OR NEGLIGENCE) FOR ANY OTHER DAMAGES, WHETHER DIRECT, IMMEDIATE, FORESEEABLE, CONSEQUENTIAL, OR SPECIAL OR FOR ANY EXPENSES INCURRED BY REASON OF THE USE OR MISUSE, SALE OR FABRICATION OF PRODUCTS WHICH DO OR DO NOT CONFORM TO THE TERMS AND CONDITIONS OF THIS ORDER OR CONTRACT.

CONSEQUENTIAL DAMAGES: IN NO EVENT SHALL BUYER BE ENTITLED TO RECOVER ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES, INCLUDING BUT NOT LIMITED TO ANY COMMERCIAL LOSS OR INJURY TO ANY PERSON, WHETHER OR NOT SAID DAMAGES ARE CAUSED, IN WHOLE OR IN PART, BY ANY DELAY, FAILURE, NONPERFORMANCE OR NEGLIGENCE OF SELLER, OR THE BREACH BY SELLER OF ANY OF THE TERMS OF SALE CONTAINED HEREIN OR ANY OTHER TERM OR CONDITION MADE A PART OF THE CONTRACT BETWEEN SELLER AND BUYER.

RETURNS: Return material shipments shall be prepaid and clearly marked with a Sales Shipping Authorization (SSA) number issued by the Seller. Items returned for repair shall include detailed information about the application/installation, and the nature of the trouble experienced. Credit may be issued by the Seller for unused, current product, returned in saleable condition, after deduction of a restocking fee, typically 25% of the purchase price. Warranty coverage, or credit consideration, will be determined only after receipt and inspection of the material by the Seller.

BOND PREMIUMS: In the event the Seller shall be required as a condition of the manufacture and sale of equipment to furnish a performance bond, the buyer shall pay as a part of the purchase price of said equipment all bond premiums and expense in connection therewith.

DESIGNS: All designs and specifications shown in Seller’s catalog are subject to change without notice.

PATENT INFRINGEMENT: The Seller will hold the purchaser and user harmless from infringement of any United States patent covering equipment of its manufacture. This, of necessity, is limited to the equipment per se and cannot be extended to applications of such equipment by others. The purchaser and user shall advise the Seller immediately in the event any claims of infringement are brought to their attention.

COMPLIANCE WITH LAWS: Seller has complied with all applicable Federal, State and local laws and regulations in connection with the manufacture and sale of all equipment. No responsibility or liability will be taken for import duties, laws, regulations or taxes imposed by any foreign country.

GOVERNING LAW: This contract shall be governed by, construed, and enforced in accordance with the laws of the State of Pennsylvania.

ERRORS: All clerical errors are subject to correction.


NOTES


NOTES

Warren Controls was founded in the early 1950’s and was known as Warren Automatic Controls. Warren is the name of the county in New Jersey where the business was founded. The first products were regulators designed for the HVAC and marine industries. The company was purchased and renamed Warren Controls Corporation in 1971, largely specializing and growing in a variety of flow control products for commercial, industrial, and military applications.

In 2003, Warren Controls Inc., as we are known today now resides in a modern 60,000 Sq. Ft. manufacturing facility in Bethlehem, PA. Our product lines continue to grow through extensive product development and target marketing. Today, Warren offers four broad product lines for Building Automation Control Valves, Industrial Process Valves up to ANSI Class 300, Mechanical Level Controls for deaerators and boilers, and Military / Marine Valves to MIL specifications.

We serve a variety of end use and OEM customers and manage an extensive independent representative and distribution sales network. Find out who the local Sales Agent is in your area. Or, feel free to contact the company directly to answer your questions and serve your needs.

2600 EMRICK BLVD • BETHLEHEM, PA 18020 • USA •800-922-0085 • WWW.WARRENCONTROLS.COMDEPENDABLE, RUGGED, PRECISION CONTROL VALVES AND ACCESSORIES

Documents

Control Valve Products for HVAC / BAC - Apex …apexsolutionsmn.com/wp-content/uploads/2015/10/HVACBAC-3...Control Valve Products for HVAC / BAC (Heating, Ventilation, and Air Conditioning