F03MSV-ND* - FLOW

CONTROL VALVE, NON-COMPENSATED W

ITH CHECK

5505 WEST 123RD STREET • SAVAGE, MN 55378-1299 / PH: 952.895.6400 / WWW.CONTINENTALHYDRAULICS.COM

CONTINENTAL HYDRAULICS

F03MSV-ND*FLOW CONTROL VALVE, NON-COMPENSATED WITH CHECK

2 WWW.CONTINENTALHYDRAULICS.COM - SALES@CONTHYD.COM

TOUGHF0

3MSV

-ND*

- FL

OW C

ONTR

OL V

ALVE

, NON

-COM

PENS

ATED

WIT

H CH

ECK F03MSV-ND*

FLOW CONTROL VALVE, NON-COMPENSATED WITH CHECK

DESCRIPTIONThis modular stack valve is a non-compensated flow control valve with a check valve for reverse free flow.

OPERATIONS This valve increases its orifice value from fully closed to fully open with counter-clockwise rotation.

Meter-in or meter-out configuration is determined by the orientation of the body to mounting surface.

Available with flow control function on line A, B, or both A + B.

AVAILABLE VERSIONS

TYPICAL PERFORMANCE SPECIFICATIONS

MAXIMUM OPERATING PRESSURE 5000 psi 350 bar

CRACKING PRESSURE 7 psi 0.5 bar

MAXIMUM FLOW RATE

Controlled Lines 13 gpm 50 l/min

Free Lines 20 gpm 75 l/min

MINIMUM FLOW RATEControlled Lines

with ∆P = 145 psi≤ 0.015 gpm ≤ 0.06 l/min

MOUNTING SURFACENFPA D03

ISO 4401-03-02-0-05

WEIGHT 2.87 lbs 1.3 kg

F03MSV-NDAMETER-OUT

METER-IN

F03MSV-NDBMETER-OUT

METER-IN

F03MSV-NDCMETER-OUT

METER-IN

SALES@CONTHYD.COM - WWW.CONTINENTALHYDRAULICS.COM 3

BODY MATERIAL

C Cast Iron

SEAL

A Buna (STD)

G Viton

F03MSV-ND -

TYPICAL ORDERING CODE:

F03MSV-NDA-AC-D

IDENTIFICATION CODE

PERFORMANCE CURVES

DESIGN LETTERC -

CONTROL PORT

A Port A

B Port B

C Port A and B

F03MSV-ND* - FLOW

CONTROL VALVE, NON-COMPENSATED W

ITH CHECK

CURVE FLOW PATH

1 P port, T port

2 A port or B port w/o flow control

3 Reverse free flow thru check

NOTE:Values obtained with oil viscosity of 36 cSt at 122°F (50°C).

CONTROLLED PORT ADJUSTMENT

PRESSURE DROPS Δp - Q

4 WWW.CONTINENTALHYDRAULICS.COM - SALES@CONTHYD.COM

F03M

SV-N

D* -

FLOW

CON

TROL

VAL

VE, N

ON-C

OMPE

NSAT

ED W

ITH

CHEC

K

Identification Label

F03MSV-NDA

F03MSV-NDC MOUNTING - TOP VIEW

F03MSV-NDB

DIMENSIONSDimensions in mm [IN]

Meter-Out

Meter-In

Pin HoleLabel

O-Ring Subplate (Included In The Delivery)

HexagonalHeadAdjustmentScrew. 13 mm [ 1/2 ] Wrench

NOTE:Remove directional control valve locator pin when configuring for

meter-in.

SALES@CONTHYD.COM - WWW.CONTINENTALHYDRAULICS.COM 5

F03MSV-ND* - FLOW

CONTROL VALVE, NON-COMPENSATED W

ITH CHECK

APPLICATION DATAFLUIDSAll pressure drops shown on these data pages are based on 170 SUS fluid viscosity and 0.87 specific gravity. For any other specific gravity (G1) the pressure drop (∆P) will be approx. ∆P1 = ∆P (G1/G). See the chart for other viscosities.

Use mineral oil-based hydraulic fluids HL or HM type, according to ISO 6743-4. For these fluids, use NBR seals. For fluids HFDR type (phosphate esters) use FPM seals (code G). For the use of other kinds of fluid such as HFA, HFB, HFC, please consult our technical department.

Using fluids at temperatures higher than 180 °F causes the accelerated degradation of seals as well as degradation of the fluids physical and chemical properties.

From a safety standpoint, temperatures above 130 degrees F are not recommended.

FLUIDVISCOSITIES

Cst 10 14.5 32 36 43 54 65 76 86 108 216 324 400

SUS 60 75 150 170 200 250 300 350 400 500 1000 1500 1900

MULTIPIER 0.77 0.81 0.97 1.00 1.04 1.10 1.15 1.20 1.24 1.31 1.56 1.72 1.83

RANGE TEMPERATURES: Ambient - 4 to +130 °F -20 to +54 °C

Fluid - 4 to +180 °F -20 to +82 °C

FLUID VISCOSITYRange 60 -1900 SUS 10 - 400 cSt

Recommended 120 SUS 25 cSt

FLUID CONTAMINATION ISO 4406:1999 Class 20/18/15

SEAL KIT

BUNA SEAL KIT 1013661

VITON SEAL KIT 1013662

F03M

SV-N

D* -

FLOW

CON

TROL

VAL

VE, N

ON-C

OMPE

NSAT

ED W

ITH

CHEC

K

FORM NO. 1013015. REV. 12/2011. © 2011 CONTINENTAL HYDRAULICS. ALL RIGHTS RESERVED. PRODUCT SPECIFICATIONS AND APPEARANCE ARE SUBJECT TO CHANGE WITHOUT NOTICE.

ABOUT CONTINENTAL HYDRAULICSRugged, durable, high-performance, ef�cient—the reason Continental Hydraulics’ products are used in some of the most challenging applications across the globe. With a commitment to quality customer

support and innovative engineering, Continental’s pumps, valves, power units, mobile and custom products deliver what the markets demand. Continental has been serving the food production, brick

and block, wood products, automotive and machine tool industries since 1962. Learn how our products survive some of the most harsh environments.

SALES@CONTHYD.COM5505 WEST 123RD STREET • SAVAGE, MN 55378-1299 / PH: 952.895.6400 / FAX: 952.895.6444 / WWW.CONTINENTALHYDRAULICS.COM