Upload
vominh
View
213
Download
0
Embed Size (px)
Citation preview
4
Sicherheit durch QualitätSafety through qualityDIATEST
I N H A LTC O N T E N T S
Page
5 Split-ball probes
6 Technical data7 Design, travel transfer, operating principle,
range of application8 Accessories
10 Checking stands12 DIATEST small bore gauges, standard,
carbide and blind bore for bore hole Ø 0.47 mm to 41.1 mm (mm-version)
15 DIATEST laboratory bore gauges,range 0.47 mm to 30.60 mm (mm-version)
15 Technical information16 DIATEST small bore gauges, standard,
carbide and blind bore for bore hole Ø 0.0185“ to 1.6200“ (inch-version)
19 DIATEST laboratory bore gauges,range 0.0185“ to 1.13“ (inch-version)
20 DIATEST-T-probes to measure deeper bores, Ø 2.05 to 9.80 mm (mm-version)20 DIATEST-T-probes and sets to measure
deeper bores, Ø 0.081“ to 0.388“(inch-version)
22 DIATEST-3-point-probes for bores from 4.75 mm to 150.60 mm or0.187“ to 5.929“(mm- and inch-version)
23 DIATEST-PA-probes to measure paralleldistances from 4.7 mm to 41.1 mm or 0.185“ to 1.618“ (mm- and inch-version)
5
Split-ball probes are universal boregauges for indicating internalmeasurements. The modular de-sign with extensive accessoriesenables gauging of most commonbores. This allows use for serialand individual control as well aspreferentially in the plant directlyat the production machine.Due to different styles throughbores, blind bores, paralleldistances, etc. can be gauged.
T-T-
T-
R-
T-FB
MH6-73-R
S P L I T - B A L L P R O B E S
Sicherheit durch QualitätSafety through qualityDIATEST
6
T-3P
T-PA
Ø kleiner 8,2 mm)
Technical data
Operating range:Standard split-ball probein hard chrome:Ø 0.47 – 41.1 mmStandard split-ball probe withcarbide contacts:Ø 1.5 – 41.1 mm (for heavy wear conditions)Standard split-ball probe withceramic contacts:Ø 3.7 – 41.1 mm (for softmaterials like aluminium etc.)
Blind bore split-ball probe: Ø1.5 – 41.1 mm (for gaugingclose to bottom of bore)
3-point split-ball probe :Ø 4.75 – 150,6 mm (gaugingof polygon-shaped workpieces)
T-probes: Ø 2.05 – 9.8 mm(for gauging deep bores withØ smaller than 8.2 mm)
Measuring range:0.06 mm up to 2.2 mm(according to size of probe)
Accuracies:Repeatability (standard split-ballprobes):
Manual gauging c. 1 μm,Stationary gauging in stand< 0,5 μm
Linearity (standard split-ballprobes):
Size 0.5 – 1.50 max. 2%of travel, min. 0.001 mmSize 1.75 – 40 max. 1%Size 1.75 – 40 max. 1%of travel, min. 0.001 mm
Calibration with setting ringMeasuring depth:
Up to Ø 4.2 max. 750 mm(T-probes with TV2/TV2,5)Ø > 4.2 – 8.3 max. 1000 mm(T-probes with TV4)Ø > 8.3 – 41.1 several metres(standard split-ball probes withTV8)
Contact points:Standard version in hardchrome, different materials likecarbide, ceramic (depending on size). Special shapes for blind bores,parallel distances (grooves)
Special shapes on request
7
T-PA T-3PT-ZM
T-ZG Super-FB Einstich-Tastkopf
ring pressure of the indicating unitand centre themselves in the bore.The gauge is zero-set (calibrated)in a setting ring. When gaugingby hand, determine axial cente-ring by rocking gauge assemblyin bore (see below ill., middle).Reversal point of Indicator handshows measured value. Whenchecking stands are used, rockingmovement is not required.
Range of operation
Apart from bore diametersDIATEST split-ball probes candetect geometrical shape defectssuch as ovality, concentricity,barrel-shape, etc. Besides, split-ball probes are available for gau-ging parallel distances, groovetoothing (serration), internal gearsand recesses.Special shapes on requestSend drawing, workpiece sampleand description of gaugingmethod with inquiry.Some special shapes of DIATESTsplit-ball bore gauges:– T-ZG: bore gauging with centre
stud (on request)– Super-FB: blind bore gauging
up to c. 0.1 mm to bore ground(on request)
– Recess-probe: diameter gaugingof recesses (on request)
– T-PA: gauging of paralleldistances (see page 6)
– T-ZM: gear gauging fromMi = 3.5 mm (see leaflet“Internal Gear Gauges“)
– T-3P: gauging of polygon shapes from Ø 4.75 mm(see page 6)
Design
A split-ball probe unit consists ofat least 5 parts:Probe (4) made of hardened steel– in standard version chromedc. 1000 HVTapered needle (3) made of har-dened steel or carbide with lappedtaper.Hardness steel needle: 62-64HRC, hardness carbide needle:c. 1600 HVIndicator holder (2) MH6-51with clamp 8H6 or MH6-51-Zwith clamp 3/8“, retracting indi-cator holder MH6-73-RIndicating unit (1) any mechanicalor electronic indicator, micro com-parator or electronic probe withdisplaySetting ring: DIATEST setting ringsare available in metric or inchsizes. Rings up to Ø 1.5 have aninsert made of synthetic sapphire,all other sizes are made of arti-ficially aged and wear resistantspecial steel. DIATEST setting ringscan only be supplied in fixed sizesaccording to works standard.Intermediate sizes can only besupplied as DIN 2250-C settingrings.
Travel transmission
The lapped taper of the needletransfers the spreading movementof the split-ball probe in a 1:1ratio to the indicator.
Working Principle
The semicircular anvils of theprobe are spread by the measu-
2
4
3
1
8
Sicherheit durch QualitätSafety through qualityDIATEST
Depth extensions forT-probes …
… are required in combinationwith T-probes for measuringdeeper bores smaller thanØ 8.3 mm. Diameter of extensiondepends on design of T-probe:TV2 (Ø 2.0), TV2.5 (Ø 2.5),TV4 (Ø 4.0). Extensions are avai-lable in different lengths fromL = 20 mm up to L = 1000 mm(depending on extension).Connection thread of one side isalways M6 x 0.75. This allowsconnection of all accessories.T-extensions are temperature-stabilized.(T-GL: To measure the groove-Ø of twistedgrooved tubes, like e.g. gun barrels. Measuringrange of probes: Corresponding to T- or standardprobes – see tables on page 12-14 and 20-21).
Accessories
A large assortment of accessoriescomplete the split-ball-pro-gramme. The standard connectionthread M6 x 0.75 enables amultiple combination of theindividual gauging elementsaccording to the measuring job.
Retracting indicator holder(MH6-73-R)
For easy entry in bore.
Depth extension TV8(Ø 8,0)
For measuring deeper bores fromc. Ø 8.2 mm. Available in differentlengths from L = 20 mm up toL = 1000 mm. From TV8-80(L = 80) depth extensions are tem-perature-stabilized.
TV8
T-T
TV4
MH6-73-R
T-GL
T-FB
9
Depth stops (TA8…)
Ideal for gauging bores at aspecific depth. Also search forreversal point can be omitted. Thedepth stop TA8-24 is clampedonto depth extension TV8. Thestop ring Ø 24 is interchangeablewith stop rings Ø 45 or Ø 60.It is also possible to screw on aspecial stop ring instead of thediscs.
Right angle attachment(W6)
Screwed between holder andprobe where clearance betweentool and workpiece is limited.Minimum distance between rightangle attachment and obstacle:27 mm plus length of probe(see table page 14).
Rotary adapter (TV64-D)
Probe can be turned in bore whiledial indicator remains stationary.Specially suitable for roundnessmeasuring of workpieces whichcannot be turned.
TV64-D
MH6-51
W6TA8
TA8
Sicherheit durch QualitätSafety through qualityDIATEST
10
This is particularly important whenshape defects are detected.Accessories like e.g. floating hol-der and vee attachment enable areliable and fast transaction ofgauging also for unskilled workers.By using adjustable depth stopsone can carry through measure-ments in indicated depths.Specially beneficial is the use ofstands directly on the workingplace for bore control during pro-duction.
Checking stands
In combination with split-ball pro-bes checking stands offer a safebasis for an exact and fast boregauging (measuring of Ø, bellmouth, conical form, barrel shape,roundness etc.). Search for rever-sal point is omitted. Amount ofstroke can be set precisely.
MST102
MST58
11
Universal checking stand(MST102)
This checking stand is suitable forlarger sizes. The measuring strokeis continuously adjustable from0 – 130 mm. The vee attachment(standard accessory) or other cen-tering devices can be mountedon the platen (100 x 100) in aT-slot.
Extras:– Collar for Ø 30 mm c/w dial
gauge bracket for precise heightadjustment
– Platens in different widths(130 mm and 160 mm)
– Jib arms (150 mm and200 mm) for larger work-pieces and BMD-floating holders(SH-BMD30)
Floating holder (SH-T)
It allows the split-ball probe, whichis clamped in the checking stand,a slight “floating“ in horizontalplane. A probe easily finds theexact axis when entering into thebore. Floating range continuouslyadjustable from 0 to 1.5 mm(until 3 mm without regulation).
Version SH-T-F for adjustment ofmeasuring pressure.
Checking stand (MST58)
The MST58 is easy to handle andespecially suitable for small work-pieces. The measuring stroke iscontinuously adjustable from0 – 35 mm. With the checkingnut you can easily and exactlyadjust the height. The diameterof platen is 58 mm.
Extras:– For easy positioning a clamp-
on-vee (MST-WA) can be fixedto platen
– Perforated platen (MST-MT80) for measuring through bores up to Ø 13 mm
MST-MT80
MST-WA
SH-T
0,47– 0,53 0,52 – 0,58
0,57 – 0,670,65 – 0,770,75 – 0,870,85 – 0,97
0,95 – 1,151,07 – 1,251,17 – 1,351,27 – 1,451,37 – 1,55
1,50 – 1,901,80 – 2,202,05 – 2,45
2,30 – 2,702,55 – 2,952,80 – 3,203,05 – 3,453,30 – 3,703,55 – 3,95
3,80 – 4,20
3,70 – 4,304,20 – 4,804,70 – 5,305,20 – 5,805,70 – 6,306,20 – 6,806,70 – 7,307,20 – 7,807,70 – 8,308,20 – 8,808,70 – 9,309,20 – 9,80
9,70 – 10,30
9,40 – 10,6010,40 – 11,6011,40 – 12,6012,40 – 13,6013,40 – 14,6014,40 – 15,6015,40 – 16,6016,40 – 17,6017,40 – 18,6018,40 – 19,6019,40 – 20,60
20,40– 21,6021,40 – 22,6022,40 – 23,6023,40 – 24,6024,40 – 25,6025,40 – 26,6026,40 – 27,6027,40 – 28,6028,40 – 29,6029,40 –30,60
28,90– 31,1030,90 – 33,1032,90 – 35,1034,90 – 37,1036,90 – 39,1038,90 – 41,10
T-0,50T-0,55
T-0,60T-0,70T-0,80T-0,90
T-1,0T-1,1T-1,2T-1,3T-1,4
T-1,75T-2,00T-2,25
T-2,50T-2,75T-3,00T-3,25T-3,50T-3,75
T-4,00/1
T-4,0T-4,5T-5,0T-5,5T-6,0T-6,5T-7,0T-7,5T-8,0T-8,5T-9,0T-9,5
T-10,0/2
T-10T-11T-12T-13T-14T-15T-16T-17T-18T-19T-20
T-21T-22T-23T-24T-25T-26T-27T-28T-29T-30
T-30/5T-32T-34T-36T-38T-40
M00
M0
M1
M2
M3
M4
M5
T-HM-1,75T-HM-2,00T-HM-2,25
T-HM-2,50T-HM-2,75T-HM-3,00T-HM-3,25T-HM-3,50T-HM-3,75
T-HM-4,00/1
T-HM-4,0T-HM-4,5T-HM-5,0T-HM-5,5T-HM-6,0T-HM-6,5T-HM-7,0T-HM-7,5T-HM-8,0T-HM-8,5T-HM-9,0T-HM-9,5
T-HM-10,0/2
T-HM-10T-HM-11T-HM-12T-HM-13T-HM-14T-HM-15T-HM-16T-HM-17T-HM-18T-HM-19T-HM-20
T-HM-21T-HM-22T-HM-23T-HM-24T-HM-25T-HM-26T-HM-27T-HM-28T-HM-29T-HM-30
T-HM-30/5T-HM-32T-HM-34T-HM-36T-HM-38T-HM-40
M1-HM
M2-HM
M3-HM
M4-HM
M5-HM
T-KE-4,0T-KE-4,5T-KE-5,0T-KE-5,5T-KE-6,0T-KE-6,5T-KE-7,0T-KE-7,5T-KE-8,0T-KE-8,5T-KE-9,0T-KE-9,5
T-KE-10,0/2
T-KE-10T-KE-11T-KE-12T-KE-13T-KE-14T-KE-15T-KE-16T-KE-17T-KE-18T-KE-19T-KE-20
T-KE-21T-KE-22T-KE-23T-KE-24T-KE-25T-KE-26T-KE-27T-KE-28T-KE-29T-KE-30
T-KE-30/5T-KE-32T-KE-34T-KE-36T-KE-38T-KE-40
M2-KE
M3-KE
M4-KE
M5-KE
T-FB-1,75T-FB-2,00T-FB-2,25
T-FB-2,50T-FB-2,75T-FB-3,00T-FB-3,25T-FB-3,50T-FB-3,75
T-FB-4,00/1
T-FB-4,0T-FB-4,5T-FB-5,0T-FB-5,5T-FB-6,0T-FB-6,5T-FB-7,0T-FB-7,5T-FB-8,0T-FB-8,5T-FB-9,0T-FB-9,5
T-FB-10,0/2
T-FB-10T-FB-11T-FB-12T-FB-13T-FB-14T-FB-15T-FB-16T-FB-17T-FB-18T-FB-19T-FB-20
T-FB-21T-FB-22T-FB-23T-FB-24T-FB-25T-FB-26T-FB-27T-FB-28T-FB-29T-FB-30
T-FB-30/5T-FB-32T-FB-34T-FB-36T-FB-38T-FB-40
M1-FB
M2-FB
M3-FB
M4-FB
M5-FB
DIATEST small bore gauges, standard, carbide and blind borefor bore hole Ø 0.47 mm to 41.1 mm.
Range(Bold type =measuring
range of set)
mm
2)Split-ball probes, complete sets1), setting ring sets2)
Standard probeshard chrome plated
Standard probescarbide inserted
Standard probesceramic inserted
Blind bore probeshard chrome plated
Gerät 1)Set 1)
Best.-Nr.OrderCode
EinzelnSingle
Best.-Nr.OrderCode
Gerät 1)Set 1)
Best.-Nr.OrderCode
EinzelnSingle
Best.-Nr.OrderCode
Gerät 1)Set 1)
Best.-Nr.OrderCode
EinzelnSingle
Best.-Nr.OrderCode
Gerät 1)Set 1)
Best.-Nr.OrderCode
EinzelnSingle
Best.-Nr.OrderCode
12
N00-030
N00-040
N0-070
N1-100
N1-150
N2-270
N3-310
N3-310
N5-350
NFB1-100
NFB1-150
NFB2-270
NFB3-310
NFB3-310
NFB5-350
R-0,500R-0,550R-0,600R-0,700R-0,800R-0,900
R-1,000R-1,100R-1,200R-1,300R-1,400
R-1,750R-2,000R-2,250R-2,500R-2,750R-3,000R-3,250R-3,500R-3,750
R-4,000R-4,500R-5,000R-5,500R-6,000R-6,500R-7,000R-7,500R-8,000R-8,500R-9,000R-9,500
R-10,000R-11,000R-12,000R-13,000R-14,000R-15,000R-16,000R-17,000R-18,000R-19,000R-20,000
R-21,000R-22,000R-23,000R-24,000R-25,000R-26,000R-27,000R-28,000R-29,000R-30,000
R-30,000R-32,000R-34,000R-36,000R-38,000R-40,000
Standardneedles
Blind boreneedles
Set ofsetting rings 2)
Standardnominal sizes
inter-mediatesizes
HartmetallCarbide
Best.-Nr.OrderCode
StahlSteel
Best.-Nr.OrderCode
HartmetallCarbide
Best.-Nr.OrderCode
StahlSteel
Best.-Nr.OrderCode
Best.-Nr.OrderCode
Best.-Nr.OrderCode
Best.-Nr.OrderCode
13
NHM0-070
NHM1-100
NHM1-150
NHM2-270
NHM3-310
NHM3-310
NHM5-350
NFB-HM1-100
NFB-HM1-150
NFB-HM2-270
NFB-HM3-310
NFB-HM3-310
NFB-HM5-350
RM00
RM0
RM1
RM2
RM3
RM4
RM5
R-1,500
R-5,750R-7,750
R-10,500R-11,500R-12,500R-13,500R-14,500R-15,500R-16,500R-17,500R-18,500R-19,500
R-20,500R-21,500R-22,500R-23,500R-24,500R-25,500R-26,500R-27,500R-28,500R-29,500
R-31,000R-33,000R-35,000R-37,000R-39,000
Needles Setting rings
Lengthof probes
L 3)
Max. measuringdepth
M 3)
Min. measuringheight
(Standard probe)
H1 3)
Measuringpressure
of dial gauge
N(ca)
Min. measuringheight
(Blind bore probe)
H2 3)
Sicherheit durch QualitätSafety through qualityDIATEST
1) A complete set contains:Wooden box with range chart (space for setting rings is left), split-ball probes and needles, standard holder MH6-51 and wrench SW7-G.
2) Extent of set: See setting rings standard nominal sizes.
3) See sketch page 15.
14
1,51,82,02,52,83,0
11
17
22
40
50
50
90
100
19,5
19,5
25,3
30,6
47,3
48,5
48,5
48,5
0,250,270,290,310,330,35
0,6
0,9
1,2
2
3,3
3,6
4
0,3
0,5
1,0
1,2
1,5
0,3 – 0,6
0,5 – 0,8
0,8 – 1
1,2 – 1,8
1,5 – 2
1,5 – 2,5
1,5 – 2,5
Technical information
DIATEST laboratory bore gauges,range 0.47 mm to 30.60 mm.
Range Standard probeshard chrome plated
Standard probescarbide inserted
Standard probesceramic inserted
Blind bore probeshard chrome plated
Set ofsetting rings 2)
Maximum measuring depth MDepends on probe size. For deter-mination of max. measuring depth.Insert bore gauge partly into boreup to indicator.Larger measuring depths from:Ø 8.20 mm with extensionØ 2.05 mm with T-probesØ 0.95 mm with special probes
Length of probes LWhen space is limited and rightangle attachment is used, minimumdistance between bore obstruction= 27 mm + length of probes (L).
Minimum measuring height HIndicates how close to bore groundcan be gauged when probe isspread to maximum.
Geräte 1)Sets 1)
Best.-Nr.Order Code
Geräte 1)Sets 1)
Best.-Nr.Order Code
Geräte 1)Sets 1)
Best.-Nr.Order Code
Geräte 1)Sets 1)
Best.-Nr.Order Code
Best.-Nr.Order Code
0,47 – 1,550,95 – 3,951,50 – 9,801,50 – 20,603,70 – 30,60
M000M01M12M123M234
M12-HMM123-HMM234-HM M234-KE
M12-FBM123-FBM234-FB
RM000RM01RM12RM123RM234
mm
1) A complete set contains:Wooden box with range chart (space for setting rings is left), split-ball probes and needles, standard holder MH6-51 and wrench SW7-G.
2) Extent of set: See setting rings standard nominal sizes.
15
Several basic sets in one box
Technical information
Blind bore probe
Standard probe
DIATEST small bore gauges, standard, carbide and blind borefor bore hole Ø 0.0185“ to 1.6200“.
0.0185 – 0.02100.0205 – 0.0228
0.0224 – 0.02640.0256 – 0.03000.0295 – 0.03430.0335 – 0.0380
0.0375 – 0.04500.0430 – 0.04900.0470 – 0.05300.0510 – 0.05700.0540 – 0.0610
0.057 – 0.0750.067 – 0.0850.081 – 0.096
0.091 – 0.1100.105 – 0.1260.120 – 0.1400.134 – 0.1550.149 – 0.169
0.165 – 0.2000.185 – 0.2200.209 – 0.2440.235 – 0.2700.260 – 0.2950.288 – 0.3230.313 – 0.3470.335 – 0.3700.360 – 0.394
0.380 – 0.4250.420 – 0.4800.474 – 0.5310.524 – 0.5830.573 – 0.6340.622 – 0.6810.672 – 0.7300.721 – 0.7800.772 – 0.830
0.833 – 0.8800.872 – 0.9300.922 – 0.9800.972 – 1.0361.022 – 1.0801.072 – 1.130
1.130 – 1.2201.210 – 1.3001.290 – 1.3801.370 – 1.4601.450 – 1.5401.530 – 1.620
T-0XT-00
T-01T-02T-03T-04
T-05T-06T-07T-07T-08T-08T-09T-09
T-011T-012T-013
T-014T-015T-016T-017T-018
T-021T-021T-022T-022T-023T-023T-024T-024T-025T-025T-026T-026T-027T-027T-028T-028T-029T-029
T-031T-032T-033T-034T-035T-036T-037T-038T-039
T-041T-041T-042T-042T-043T-043T-044T-044T-045T-045T-046T-046
T-051T-052T-053T-054T-055T-056
E00
E0E
E1
E2E
E3
E4
E5
T-HM-011T-HM-012T-HM-013
T-HM-014T-HM-015T-HM-016T-HM-017T-HM-018
T-HM-021T-HM-021T-HM-022T-HM-022T-HM-023T-HM-023T-HM-024T-HM-024T-HM-025T-HM-025T-HM-026T-HM-026T-HM-027T-HM-027T-HM-028T-HM-028T-HM-029T-HM-029
T-HM-031T-HM-032T-HM-033T-HM-034T-HM-035T-HM-036T-HM-037T-HM-038T-HM-039
T-HM-041T-HM-041T-HM-042T-HM-042T-HM-043T-HM-043T-HM-044T-HM-044T-HM-045T-HM-045T-HM-046T-HM-046
T-HM-051T-HM-052T-HM-053T-HM-054T-HM-055T-HM-056
E1-HM
E2-HMM
E3-HM
E4-HM
E5-HM
T-KE-021T-KE-021T-KE-022T-KE-022T-KE-023T-KE-023T-KE-024T-KE-024T-KE-025T-KE-025T-KE-026T-KE-026T-KE-027T-KE-027T-KE-028T-KE-028T-KE-029T-KE-029
T-KE-031T-KE-032T-KE-033T-KE-034T-KE-035T-KE-036T-KE-037T-KE-038T-KE-039
T-KE-041T-KE-041T-KE-042T-KE-042T-KE-043T-KE-043T-KE-044T-KE-044T-KE-045T-KE-045T-KE-046T-KE-046
T-KE-051T-KE-052T-KE-053T-KE-054T-KE-055T-KE-056
E2-KE
E3-KE
E4-KE
E5-KE
T-FB-011T-FB-012T-FB-013
T-FB-014T-FB-015T-FB-016T-FB-017T-FB-018
T-FB-021T-FB-021T-FB-022T-FB-022T-FB-023T-FB-023T-FB-024T-FB-024T-FB-025T-FB-025T-FB-026T-FB-026T-FB-027T-FB-027T-FB-028T-FB-028T-FB-029T-FB-029
T-FB-031T-FB-032T-FB-033T-FB-034T-FB-035T-FB-036T-FB-037T-FB-038T-FB-039
T-FB-041T-FB-041T-FB-042T-FB-042T-FB-043T-FB-043T-FB-044T-FB-044T-FB-045T-FB-045T-FB-046T-FB-046
T-FB-051T-FB-052T-FB-053T-FB-054T-FB-055T-FB-056
E1-FB
E2-FB
E3-FB
E4-FB
E5-FB
Range(Bold type =measuring
range of set)
inch
Standard probescarbide inserted
Standard probesceramic inserted
Blind bore probeshard chrome plated
Gerät 1)Set 1)
Best.-Nr.OrderCode
EinzelnSingle
Best.-Nr.OrderCode
Gerät 1)Set 1)
Best.-Nr.OrderCode
EinzelnSingle
Best.-Nr.OrderCode
Gerät 1)Set 1)
Best.-Nr.OrderCode
EinzelnSingle
Best.-Nr.OrderCode
Gerät 1)Set 1)
Best.-Nr.OrderCode
EinzelnSingle
Best.-Nr.OrderCode
16
)Split-ball probes, complete sets 1), setting ring sets2)
N00-030
N00-040
N0-070
N1-100
N1-150
N2-270
N3-310
N3-310
N5-350
NFB1-100
NFB1-150
NFB2-270
NFB3-310
NFB3-310
NFB5-350
R-0XR-00R-01R-02R-03R-04
R-05R-06R-07R-08R-09
R-011R-012R-013R-014R-015R-016R-017R-018
R-021R-022R-023R-024R-025R-026R-027R-028R-029
R-031R-032R-033R-034R-035R-036R-037R-038R-039
R-041R-042R-043R-044R-045R-046
R-051R-052R-053R-054R-055R-056
0.0200.0220.0250.0280.0320.036
0.0400.0450.0500.0550.060
0.06250.07500.08750.10000.11500.13000.14500.1600
0.18000.20000.22500.25000.27500.30000.32500.35000.3750
0.40000.45000.50000.55000.60000.65000.70000.75000.8000
0.85000.90000.95001.00001.05001.1000
1.18001.26001.34001.42001.50001.5800
Standardneedles
Blind boreneedles
Set ofsetting rings 2)
Standardnominal sizes
Nominal sizeInch
HartmetallCarbide
Best.-Nr.OrderCode
StahlSteel
Best.-Nr.OrderCode
HartmetallCarbide
Best.-Nr.OrderCode
StahlSteel
Best.-Nr.OrderCode
Best.-Nr.OrderCode
0,50800,55880,63500,71120,81280,9144
1,01601,14301,27001,39701,5240
1,58751,90502,22252,54002,92103,30203,68304,0640
4,5725,0805,7156,3506,9857,6208,2558,8909,525
10,16011,43012,70013,97015,24016,51017,78019,05020,320
21,59022,86024,13025,40026,67027,940
29,97232,00434,03636,06838,10040,132
inch sizein mm
17
NHM0-070
NHM1-100
NHM1-150
NHM2-270
NHM3-310
NHM3-310
NHM5-350
NFB-HM1-100
NFB-HM1-150
NFB-HM2-270
NFB-HM3-310
NFB-HM3-310
NFB-HM5-350
RE00
RE0
RE1
RE2
RE3
RE4
RE5
Needles Setting rings
Sicherheit durch QualitätSafety through qualityDIATEST
1) A complete set contains:Wooden box with range chart (space for setting rings is left), split-ball probes and needles, standard holder MH6-51 and wrench SW7-G.
2) Extent of set: See setting rings standard nominal sizes.
3) See sketch page 19.
Technische DatenTechnical information
Lengthof probes
L 3)mm
Max. measuringdepth
M 3)mm
Min. measuringheight
(Standard probe)
H1 3)mm
Measuringpressure
of dial gauge
N(ca)
Min. measuringheight
(Blind bore probe)
H2 3)mm
18
1,51,82,02,52,83,0
11
17
22
40
50
50
90
100
19,5
19,5
25,3
30,6
47,3
48,5
48,5
48,5
0,250,270,290,310,330,35
0,6
0,9
1,2
2
3,3
3,6
4
0,3
0,5
1,0
1,2
1,5
0,3 – 0,6
0,5 – 0,8
0,8 –1
1,2 – 1,8
1,5 – 2
1,5 – 2,5
1,5 – 2,5
Standard-TastkopfStandard probe
Sackloch-TastkopfBlind bore probe
DIATEST laboratory bore gauges,range 0.0185“ to 1.13“.
0.0185 – 0.06100.0375 – 0.16900.0570 – 0.39400.0570 – 0.83000.1650 – 1.1300
E000E01E12E123E234
E12-HME123-HME234-HM E234-KE
E12-FBE123-FBE234-FB
RE000RE01RE12RE123RE234
Range Standard probeshard chrome plated
Standard probescarbide inserted
Standard probesceramic inserted
Blind bore probeshard chrome plated
Set ofsetting rings 2)
Geräte 1)Sets 1)
Best.-Nr.Order Code
Geräte 1)Sets 1)
Best.-Nr.Order Code
Geräte 1)Sets 1)
Best.-Nr.Order Code
Geräte 1)Sets 1)
Best.-Nr.Order Code
Best.-Nr.Order Code
inch
1) A complete set contains:Wooden box with range chart (space for setting rings is left), split-ball probes and needles, standard holder MH6-51 and wrench SW7-G.
2) Extent of set: See setting rings standard nominal sizes.
Technische InformationenTechnical information
Maximum measuring depth MDepends on probe size. For deter-mination of max. measuring depth.Insert bore gauge partly into boreup to indicator.Larger measuring depths from:Ø 8.20 mm with extensionØ 2.05 mm with T-probesØ 0.95 mm with special probes
Length of probes LWhen space is limited and rightangle attachment is used, minimumdistance between bore obstruction= 27 mm + length of probes (L).
Minimum measuring height HIndicates how close to bore groundcan be gauged when probe isspread to maximum.
19
Several basic sets in one box
DIATEST-T-probes to measure deeper bores,Ø 2.05 mm to 9.80 mm.
Standard-T-probeshard chrome plated
Standard-T-probescarbide inserted
Setting rings Standard needles
Range(Bold type =measuring
range of set)
mm
T-T-2,25T-T-2,50
T-T-2,75T-T-3,00T-T-3,25T-T-3,50T-T-3,75T-T-4,00
T-T-4,5T-T-5,0T-T-5,5T-T-6,0T-T-6,5T-T-7,0T-T-7,5T-T-8,0T-T-8,5T-T-9,0T-T-9,5
2,05 – 2,452,30 – 2,70
2,55 – 2,952,80 – 3,203,05 – 3,453,30 – 3,703,55 – 3,953,80 – 4,20
4,20 – 4,804,70 – 5,305,20 – 5,805,70 – 6,306,20 – 6,806,70 – 7,307,20 – 7,807,70 – 8,308,20 – 8,808,70 – 9,309,20 – 9,80
M1-T
M2-T
T-T-HM-2,75T-T-HM-3,00T-T-HM-3,25T-T-HM-3,50T-T-HM-3,75T-T-HM-4,00
T-T-HM-4,5T-T-HM-5,0T-T-HM-5,5T-T-HM-6,0T-T-HM-6,5T-T-HM-7,0T-T-HM-7,5T-T-HM-8,0T-T-HM-8,5T-T-HM-9,0T-T-HM-9,5
M1-T-HM
M2-T-HM
R-2,250R-2,500
R-2,750R-3,000R-3,250R-3,500R-3,750R-4,000
R-4.500R-5,000R-5,500R-6,000R-6.500R-7,000R-7,500R-8,000R-8,500R-9,000R-9.500
RM1-T
RM2-T
NT1-100
NT1-150
NT2-150
NT-HM1-100
NT-HM1-150
NT-HM2-150
1) A complete set contains:Wooden box with range chart (space for setting rings is left), standard holder MH6-51, T-split-ball probes, T-needles and depthextension TV (length 64 mm), wrenches SW7-G and SW1,7-2-3-G.
DIATEST-T-probes to measure deeper bores,Ø 0.081“ to 0.388“.
T-T-013T-T-014
T-T-015T-T-016T-T-017T-T-018
T-T-021T-T-022T-T-023T-T-024T-T-025T-T-026T-T-027T-T-028T-T-029
0.081 – 0.0940.092 – 0.107
0.107 – 0.1220.122 – 0.1370.137 – 0.1520.152 – 0.167
0.166 – 0.1870.186 – 0.2120.211 – 0.2370.236 – 0.2620.261 – 0.2870.286 – 0.3120.311 – 0.3370.336 – 0.3620.361 – 0.388
E1-T
E2-T
T-T-HM-015T-T-HM-016T-T-HM-017T-T-HM-018
T-T-HM-021T-T-HM-022T-T-HM-023T-T-HM-024T-T-HM-025T-T-HM-026T-T-HM-027T-T-HM-028T-T-HM-029
E1-T-HM
E2-T-HM
R-013R-014
R-015R-016R-017R-018
R-021R-022R-023R-024R-025R-026R-027R-028R-029
RE1-T
RE2-T
Gerät 1)Set 1)
Best.-Nr.OrderCode
EinzelnSingle
Best.-Nr.OrderCode
Gerät 1)Set 1)
Best.-Nr.OrderCode
EinzelnSingle
Best.-Nr.OrderCode
SatzSet
Best.-Nr.OrderCode
EinzelnSingle
Best.-Nr.OrderCode
HartmetallCarbide
Best.-Nr.OrderCode
StahlSteel
Best.-Nr.OrderCode
NT1-100
NT1-150
NT2-150
NT-FB1-150
NT-FB2-150
Blind bore probeshard chrome plated
T-T-FB-2,75T-T-FB-3,00T-T-FB-3,25T-T-FB-3,50T-T-FB-3,75T-T-FB-4,00
T-T-FB-4,5T-T-FB-5,0T-T-FB-5,5T-T-FB-6,0T-T-FB-6,5T-T-FB-7,0T-T-FB-7,5T-T-FB-8,0T-T-FB-8,5T-T-FB-9,0T-T-FB-9,5
M1-T-FB
M2-T-FB
Gerät 1)Set 1)
Best.-Nr.OrderCode
EinzelnSingle
Best.-Nr.OrderCode
NT-FB1-150
NT-FB2-150
Blind boreneedles
StahlSteel
Best.-Nr.OrderCode
Standard-T-probeshard chrome plated
Standard-T-probescarbide inserted
Setting rings Standard needles
Range(Bold type =measuring
range of set)
inch
Gerät 1)Set 1)
Best.-Nr.OrderCode
EinzelnSingle
Best.-Nr.OrderCode
Gerät 1)Set 1)
Best.-Nr.OrderCode
EinzelnSingle
Best.-Nr.OrderCode
SatzSet
Best.-Nr.OrderCode
EinzelnSingle
Best.-Nr.OrderCode
HartmetallCarbide
Best.-Nr.OrderCode
StahlSteel
Best.-Nr.OrderCode
Blind bore probeshard chrome plated
Gerät 1)Set 1)
Best.-Nr.OrderCode
EinzelnSingle
Best.-Nr.OrderCode
Blind boreneedles
StahlSteel
Best.-Nr.OrderCode
NT-HM1-100
NT-HM1-150
NT-HM2-150
T-T-FB-015T-T-FB-016T-T-FB-017T-T-FB-018
T-T-FB-021T-T-FB-022T-T-FB-023T-T-FB-024T-T-FB-025T-T-FB-026T-T-FB-027T-T-FB-028T-T-FB-029
E1-T-FB
E2-T-FB
20
Technische DatenTechnical information
Length ofprobes
Min. measuringheight
(Standard probe)
RequiredT-extension
Measuring depthwith T-extension
L = 64 mm
Measuring pressureof dial gauge
N(ca)
25,3
30,6
31
0,9
1,2
1,7
TV2-64
TV2,5-64
TV4-64
90
95
95
0,8 – 1
0,8 – 1
1 – 1,5
Sicherheit durch QualitätSafety through qualityDIATEST
Technische DatenTechnical information
Länge derTastköpfeLength of
probes
mm
Mindest Messhöhe(Standard-Tastkopf)
Min. measuringheight
(Standard probe)mm
BenötigteT-Verlängerung
RequiredT-extension
mm
Messtiefe mitT-Verlängerung
Measuring depthwith T-extension
L = 64 mmmm
Messkraft derMessuhr
Measuring pressureof dial gauge
N(ca)
25,3
30,6
31
0,9
1,2
1,7
TV2
TV2,5
TV4
90
95
95
0,8 – 1
0,8 – 1
1 – 1,5
Min. measuringheight
(Blind bore probe)
0,3
0,5
Mindest Messhöhe(Sackloch-Tastkopf)
Min. measuringheight
(Blind bore probe)mm
0,3
0,5
21
mm
3-point probes 1)
Best-Nr.OrderCode
3-pointneedles
Best-Nr.OrderCode
inch
DIATEST-3-point-probes for boresfrom 4.75 mm to 150.6 mm/0.187“ to 5.929“.
4,75 – 5,305,25 – 5,805,75 – 6,306,25 – 6,806,75 – 7,307,25 – 7,807,75 – 8,308,25 – 8,808,75 – 9,309,25 – 9,809,75 – 10,30
10,25 – 10,8010,75 – 11,3011,25 – 11,8011,75 – 12,3012,25 – 12,8012,75 – 13,3013,25 – 13,8013,75 – 14,3014,25 – 14,8014,75 – 15,3015,25 – 15,8015,75 – 16,3016,25 – 16,8016,75 – 17,3017,25 – 17,8017,75 – 18,3018,25 – 18,8018,75 – 19,3019,25 – 19,8019,75 – 20,30
20,25 – 20,8020,75 – 21,3021,25 – 21,8021,75 – 22,3022,25 – 22,8022,75 – 23,3023,25 – 23,8023,75 – 24,3024,25 – 24,8024,75 – 25,3025,25 – 25,80
MessbereichRange= ± 0,6 mm25,4 – 26,626,4 – 27,6
usw. bis/etc. till54,4 – 55,6
55,4 – 56,656,4 – 57,6
usw. bis/etc. till74,4 – 75,6
75,4 – 76,676,4 – 77,6
usw. bis/etc. till99,4 – 100,6
100,4 – 101,6101,4 – 102,6usw. bis/etc. till149,4 – 150,6
T-3P-5,0T-3P-5,5T-3P-6,0T-3P-6,5T-3P-7,0T-3P-7,5T-3P-8,0T-3P-8,5T-3P-9,0T-3P-9,5T-3P-10,0
T-3P-10,5T-3P-11T-3P-11,5T-3P-12T-3P-12,5T-3P-13T-3P-13,5T-3P-14T-3P-14,5T-3P-15T-3P-15,5T-3P-16T-3P-16,5T-3P-17T-3P-17,5T-3P-18T-3P-18,5T-3P-19T-3P-19,5T-3P-20
T-3P-20,5T-3P-21T-3P-21,5T-3P-22T-3P-22,5T-3P-23T-3P-23,5T-3P-24T-3P-24,5T-3P-25T-3P-25,5
T-3P-26T-3P-27usw. bis/etc. tillT-3P-55
T-3P-56T-3P-57usw. bis/etc. tillT-3P-75
T-3P-76T-3P-77usw. bis/etc. tillT-3P-100
T-3P-101T-3P-102usw. bis/etc. tillT-3P-150
N3P-2-270oder/orN3P-HM2-270
N3P-3-310oder/orN3P-HM3-310
N3P-3-310oder/orN3P-HM3-310
N3P-3-310oder/orN3P-HM3-310
1) 3-point probes are carbide inserted, angular position 120°.3-point probes with different angular position and3-point blind bore probes (hard chromed) on request.
22
0.187 – 0.2090.207 – 0.2280.226 – 0.2480.246 – 0.2680.266 – 0.2870.285 – 0.3070.305 – 0.3270.325 – 0.3460.344 – 0.3660.364 – 0.3860.384 – 0.406
0.404 – 0.4250.423 – 0.4450.443 – 0.4650.463 – 0.4840.482 – 0.5040.502 – 0.5240.522 – 0.5430.541 – 0.5630.561 – 0.5830.581 – 0.6020.600 – 0.6220.620 – 0.6420.640 – 0.6610.659 – 0.6810.679 – 0.7010.699 – 0.7200.719 – 0.7400.738 – 0.7600.758 – 0.7800.778 – 0.799
0.797 – 0.8190.817 – 0.8390.837 – 0.8580.856 – 0.8780.876 – 0.8980.896 – 0.9170.915 – 0.9370.935 – 0.9570.955 – 0.9760.974 – 0.9960.994 – 1.016
MessbereichRange= ± 0,024“
1.000 – 1.0471.039 – 1.087usw. bis/etc. till2.142 – 2.189
2.181 – 2.2282.220 – 2.268usw. bis/etc. till2.929 – 2.976
2.969 – 3.0163.008 – 3.055usw. bis/etc. till3.913 – 3.961
3.953 – 4.0003.992 – 4.039usw. bis/etc. till5.882 – 5.929
Range Range
Sicherheit durch QualitätSafety through qualityDIATEST
DIATEST-PA-probes to measure parallel distancesfrom 4.7 mm to 41.1mm/0.185“ to 1.618“.
mm
4,7 – 5,35,2 – 5,85,7 – 6,36,2 – 6,86,7 – 7,37,2 – 7,87,7 – 8,38,2 – 8,88,7 – 9,39,2 – 9,8
9,4 – 10,610,4 – 11,611,4 – 12,612,4 – 13,613,4 – 14,614,4 – 15,615,4 – 16,616,4 – 17,617,4 – 18,618,4 – 19,619,4 – 20,620,4 – 21,621,4 – 22,622,4 – 23,623,4 – 24,624,4 – 25,625,4 – 26,626,4 – 27,627,4 – 28,628,4 – 29,629,4 – 30,6
28,9 – 31,130,9 – 33,132,9 – 35,134,9 – 37,136,9 – 39,138,9 – 41,1
TriebnadelnNeedles
Best.-Nr.OrderCode
PA-Tastköpfe 1)PA-probes 1)
Best.-Nr.OrderCode
TriebnadelnNeedles
Best.-Nr.OrderCode
PA-Tastköpfe 1)PA-probes 1)
Best.-Nr.OrderCode
T-PA-5,0T-PA-5,5T-PA-6,0T-PA-6,5T-PA-7,0T-PA-7,5T-PA-8,0T-PA-8,5T-PA-9,0T-PA-9,5
T-PA-10T-PA-11T-PA-12T-PA-13T-PA-14T-PA-15T-PA-16T-PA-17T-PA-18T-PA-19T-PA-20T-PA-21T-PA-22T-PA-23T-PA-24T-PA-25T-PA-26T-PA-27T-PA-28T-PA-29T-PA-30
T-PA-30/5T-PA-32T-PA-34T-PA-36T-PA-38T-PA-40
N2-270oder/orNHM2-270
N3-310oder/orNHM3-310
N5-350oder/orNHM5-350
NFB2-270oder/orNFB-HM2-270
NFB3-310oder/orNFB-HM3-310
NFB5-350oder/orNFB-HM5-350
inch
0.185 – 0.2090.205 – 0.2280.224 – 0.2480.244 – 0.2680.264 – 0.2870.283 – 0.3070.303 – 0.3270.323 – 0.3460.343 – 0.3660.362 – 0.386
0.370 – 0.4170.409 – 0.4570.449 – 0.4960.488 – 0.5350.528 – 0.5750.567 – 0.6140.606 – 0.6540.646 – 0.6930.685 – 0.7320.724 – 0.7720.764 – 0.8110.803 – 0.8500.843 – 0.8900.882 – 0.9290.921 – 0.9690.961 – 1.0081.000 – 1.0471.039 – 1.0871.079 – 1.1261.118 – 1.1651.157 – 1.205
1.138 – 1.2241.217 – 1.3031.295 – 1.3821.374 – 1.4611.453 – 1.5391.531 – 1.618
1) P-probes are hard chrome platedSpecial designs on request
T-FB-PA-5,0T-FB-PA-5,5T-FB-PA-6,0T-FB-PA-6,5T-FB-PA-7,0T-FB-PA-7,5T-FB-PA-8,0T-FB-PA-8,5T-FB-PA-9,0T-FB-PA-9,5
T-FB-PA-10T-FB-PA-11T-FB-PA-12T-FB-PA-13T-FB-PA-14T-FB-PA-15T-FB-PA-16T-FB-PA-17T-FB-PA-18T-FB-PA-19T-FB-PA-20T-FB-PA-21T-FB-PA-22T-FB-PA-23T-FB-PA-24T-FB-PA-25T-FB-PA-26T-FB-PA-27T-FB-PA-28T-FB-PA-29T-FB-PA-30
T-FB-PA-30/5T-FB-PA-32T-FB-PA-34T-FB-PA-36T-FB-PA-38T-FB-PA-40
23
Range Standard version Range Blind bore version