CONSTRUCTION STANDARDS FOR PUBLIC WORKS AND ... - Safford…

CONSTRUCTION STANDARDS

FOR

PUBLIC WORKS AND UTILITIES

WITHIN

SUBDIVISIONS AND

RIGHTS OF WAY

January 8, 2018

CITY OF SAFFORD CONSTRUCTION STANDARDS FOR

PUBLIC WORKS AND UTILITIES WITHIN SUBDIVISIONS AND RIGHTS OF WAY

Adopted by the Safford City Council on 24 January 2005 (Amended 23 April 2007)

(Amended 10 December 2007) (Amended 16 December 2013)

(Amended 08 January 2018) All work and materials for subdivisions and rights of way improvements shall conform to the following standards, requirements and related details:

I. City of Safford Municipal Electric System

A. Specifications and Drawing for 12.5/7.2 kV Line Construction, United Department of Agriculture, Rural Utilities Service Bulletin 50-3 (D 804), April 1983, or any subsequent regulation issued under Rural Utilities Service Bulletin 1728F-804.

B. Specifications and Drawings for Underground Electric Distribution, United States

Department of Agriculture, Rural Utilities Service Bulletin 1728F-806 (D 806), June 2000.

1. Exception: Direct burials are not authorized.

C. Electric Service Specifications, Salt River Project, (current edition), only Section 9,

Metering, is adopted.

D. National Electrical Safety Code (NESC), Institute of Electrical and Electronics Engineers, Inc., C2-(current edition).

II. City of Safford Municipal Gas System

A. City of Safford Gas Construction Manual, City of Safford, 23 August 2003, Revised 04 May 2006.

III. City of Safford Municipal Wastewater System

A. Standard Specifications and Details for Construction, Pima County Wastewater Reclamation, (current edition).

2

B. Uniform Standard Specifications for Public Works Construction, Maricopa Association of Governments (MAG), revised (current edition), for: municipal wastewater (sewer) system.

IV. Other Public Improvements

A. Uniform Standard Specifications for Public Works Construction, Maricopa Association of Governments (MAG), revised (current edition), for other public improvements including: earthwork, the municipal water system, concrete curbs, sidewalks, driveways, storm sewers, drainage improvements, irrigation pipes and structures, landscaping, irrigation sprinkler systems, and related infrastructure.

1. Exceptions:

a. Section 610.14 shall require Mega Lugs with Mechanical Joint Fittings to be

installed on C-900 water mains in addition to thrust blocking where necessary as per ADEQ Bulletin 10, Chapter 7, Distribution Systems.

b. Section 615.3 shall require the maximum length of an individual section of pipe to not exceed 13 feet.

c. Section 615.6 shall allow house connection taps to be with 4 or 6 inch rubber Wyes. This allowance does not apply to new main construction.

d. Section 601.4.2 shall be superseded by City of Safford Detail 68-001. B. Tucson Water Standard Specifications and Details, City of Tucson, (current edition).

Only the sections below are adopted and modify any MAG standard as follows:

1. 0210, Pipe Marking and Detecting Tape. Exception: “Detecting” tape is not authorized. Shall require #14 AWG Solid Copper Type UF, 600V (UL) direct bury tracing wire and a 600V Gel Cap Connector at each Splice.

2. 1404, Polyvinyl Chloride Pipe.

3. 1431, Hydrostatic Pressure Testing of Water Facilities.

Addition: Backflow prevention device and meter shall be used for testing lines.

4. 1433, Reclaimed Waterlines. STANDARD DETAILS:

108, JOINT USE TRENCH

3

500, FIRE HYDRANT INSTALLATION Exception: Omit Note #4: No shrink shall be used in lieu of concrete thrust block. Addition: City of Safford approved fire hydrant manufacturers are Mueller and Waterous.

115, PIPE BEDDING AND TRENCH BACKFILL Addition: Shading Material, All HDPE Pipe must be shaded with a minimum of six (6) inches of shading material over and under the pipe and a minimum of two (2) inches of shading material on all sides of the pipe. Pipe must not be installed against a trench well. A minimum of two (2) inches shall be maintained between the pipe and trench wall to accommodate shading material between pipe and trench wall. All Shading must be smooth and free of rocks and be able to sift through a 3/8” screen. There shall be a minimum of 44” finished cover.

D. City of Safford, Graham County, 2013. Only the Standard Details and Documents are Adopted and Modify any MAG Standard, Pima Standard or Tucson Water Standards as Follows:

COS-309 WATER SERVICE NOTES COS-330 AIR RELEASE VALVE INSTALLATION COS-400 DRAIN VALVE ASSEMBLY COS-1809 TEMPORARY CONNECTION FOR TESTING COS DETAIL 67-001, Sewer Pipe Bedding Detail COS DOC 67-101, Wastewater Management Department Directive for CCTV Inspection

COS DOC 66-101, Exhibit I, Material Specified for COS Residential Applications V. Exceptions Applications for exceptions to the above shall be submitted in writing to the Director of Utilities. Denials of exceptions may be appealed to the City Manager in writing within seven days of denial. The decision of the City Manager is final.

4

VI. Amendments The standards as listed above include any authorized amendments as issued by the proponent. The Safford City Council may amend any of the above standards by Council Resolution.

CITY OF SAFFORD

WASTEWATER MANAGEMENT DEPARTMENT DIRECTIVE

SUBJECT: CCTV Inspection for Sewer Construction Acceptance

STATEMENT OF PURPOSE

In order to improve the visual inspection tools for new sewer construction and to upgrade the inspection procedures to those currently used by many other Arizona utilities, all new sewers will be subject to a Closed Circuit Television (CCTV) inspection, as authorized by Arizona Department of Environmental Quality (R18-9-E301) prior to approval of as-built drawings and final acceptance of the public sewer by the City of Safford (COS).

GENERAL PROVISIONS

1. The CCTV inspection is an enhancement of certain elements of the Mirror Inspection, in addition to the established inspection tests of Mandrel, Mirror and Leakage and will be conducted by the utility contractor under the supervision of the City of Safford (COS).

2. All sewer lines will be subject to inspection by CCTV prior to as-built acceptance, and will take place after Mandrel, Mirror and Leakage Testing. The CCTV vehicle must have clear access to all manholes, and the sewer pipe shall be clean and free of dirt and debris. The optimum inspection period is after installation of dry utilities and prior to curb installation, since this period allows full vehicular access to all manholes. Every effort should be made to conduct the inspection during this period, due to unforeseen problems inspection efforts may be delayed until after this period. Inspections, regardless of timing, shall abide by the criteria established in this directive. In the event that the certified CCTV inspection cannot be completed prior to paving, and with prior written approval by the CCTV inspector, the certified inspection can take place after paving but in the event the inspection reveals needed repairs, those repairs are full responsibility of the contractor of the party applying for the permit.

3. The CCTV inspection shall consist of video equipment expressly designed for pipeline inspection purposes, must be compatible with Granite Viewer and operated by National Association of Sewer Service Companies (NASSCO) certified personnel. The video operator shall acquire a continuous video of each sewer reach and maintain a log noting the location and condition of all sags (start and stop), sewer taps and defects. The video operator shall also photograph all sags,

1 October 14, 2013 COS DOC: 67-101

taps and defects. The video shall identify deviations from the uniform slop by measuring the depth of standing water.

4. A mechanical gauge will be mounted in from of the camera to how the depth of any standing water (sag) in the invert. The gauge shall clearing indicate markings of 5/8” and 1” for pipe 8” through 12” in diameter and markings of 5/4” and 2” for pipe 15” through 24” in diameter. The following table defines the parameters for corrective action of sags: Pipe Diameter Observed Sag Corrective Action Required

8”-12” Less than 5/8 inch None

8”-12” Equal to 5/8, but less than 1 and ¼ inch YES, if longer than 10 feet, or more than 3 in 100 feet

8”-12” Equal to or greater than 1 and ¼ inch YES

G.T. 12”-24” Less than 1 and ¼ inch None

G.T. 12”-24” Equal to 1 and ¼ but less than 2 inch YES, if longer than 20 feet, or more than 6 in 100 feet

G.T. 12”-24” Equal to or greater than 2 inch YES

For pipe greater than 24 inches, sags greater than 5% of the diameter shall be reviewed by City of Safford for determination of corrective actions.

5. DVD or paper prints of CCTV inspection, including the still photos will be supplied by the CCTV inspector to the contractor of the party applying for the permit after each day’s inspection.

6. The contractor of the party applying for the permit shall bear all costs incurred in correcting deficiencies found during the CCTV inspection, and shall bear the cost of follow-up CCTV inspection, Mirror, Mandrel and Leakage testing.

AUTHORITY

Arizona Revised Statutes §9-463.01 and other state and local laws, rules and regulations which affect the collection, conveyance, treatment, and control of sanitary sewage.

PROCEDURE

1. The contractor of the party applying for the permit shall provide a tentative scheduled date for CCTV inspection at the preconstruction meeting. Scheduling for projects with special circumstances may be arranged with the CCTV inspector and City of Safford during the preconstruction meeting.

2. The contractor of the party applying for the permit shall ensure that the entire sewer system covered by a single ADEQ Construction Authorization permit is ready for inspection at the time of inspection. With prior written approval from the City of Safford Engineering, the CCTV inspection may be phased.

3. The contractor of the party applying for the permit shall ensure that all sewers are clean of dirt and debris prior to the scheduled CCTV inspection. If dirt or debris is found in the pipe, the particular reach will be rescheduled for the next available inspection date.

2 October 14, 2013 COS DOC: 67-101

4. On the day of inspection, the contractor of the party applying for the permit shall supply adequate water to each reach such that water runs through each downstream manhole, in order to provide the necessary visual indicators of sags in the pipe and manholes and to property Mirror inspect the line. The City of Safford or the CCTV inspector shall monitor the placement of water in advance of Mirroring and the CCTV inspection.

5. The City of Safford shall monitor all CCTV inspection work. The inspector shall use a defined criteria list for determining corrective action for sags. Corrective action for material defects or other construction defects shall be based on the inspector’s judgment, and in compliance with City of Safford construction standards and procedures.

6. Once the contractor of the party applying for the permit notifies the City of Safford inspector that all deficiencies have been repaired, a follow-up CCTV inspection for the corrected reach(es) shall be scheduled. Additional re-tests for Mandrel, Mirror and Leakage shall also be conducted. Follow-up CCTV inspection shall be at the cost of the contractor of the party applying for the permit.

3 October 14, 2013 COS DOC: 67-101

COS DOC 66-101

Item Description Description Manufacturer Manufacturer Part #

Meter Box for 5/8"-1" Meter 1419-12 Black Water Meter, 2 MsHI Flsh Cvr Plastic Rdr Carson1419-12, Black Water Meter with Plastic Reader Lid

Meter Fittings, 5/8" Meter-Utility Side, 1" CTS poly to 5/8" meter Meter Valve, Angle, 3/4" Meter Coupling x 1" Compression Ford BA43-342W (or equivalent)Meter Fittings, 5/8" Meter-Customer Side

Meter Valve, Lockwing w/ handle, Female I.P. x 3/4" meter coupling Ford B13-332W (or equivalent)

Corporation Stop, Valve, CC x FLR, 1" Corporation Stop Valve, 1" CC x Grip Ford FB1000-4x-G (or equivalent)

Item Description Description Manufacturer Manufacturer Part #Sewer Monument Cover w/ Lid Detail 198, Cast Iron Detail 198

Item Description Description Manufacturer Manufacturer Part #

Tracing Wire #14 AWG Solid Type UF, 600V (UL) direct bury tracing wire Service Wire Co. UF-14Wire Connectors 600V Gel Cap Connector 3M DBR-6

Placement Item Description Qty Manufacturer Part #

Bottom of AssemblyValve, Air Vent, 1", Crispin UL-10.1, 3/16 Orifice, 20-150lb Working Pressure 1 CRISPIN UL-10.1

Bottom of Assembly VALVE, CORP STOP, CCXGrip, 1" 1 FB1000-4x-G (or equivalent)Bottom of Assembly VALVE, CURBSTOP, LOCK WING, FIP, 1" 1 FORD, B11-444 (or equivalent)Bottom of Assembly COUPLING, CTS X MIP, 1" 1 FORD, C84-44 (or equivalent)Top of Assembly NIPPLE, GALV, 3/4"X12" 1Top of Assembly ELL, GALV, 90, 3/4" 1Top of Assembly ELL, GALV, STREET, 3/4" 90 1Top of Assembly VENT SCREEN (filter washer for standard garden hose) 1 Ace Hardware #70333 or equal

RESIDENTIAL SEWER APPLICATIONS

TRACING WIRE FOR MAINS AND SERVICE LINES

AIR VENT, 1"

EXHIBIT IMaterial Specified for City of Safford

Residential ApplicationsRESIDENTIAL WATER APPLICATIONS

Revision Date 4/2003©2008 Oldcastle Precast, Inc.

Pomona, CaliforniaToll-Free: 800.735.5566Phone: 909.634.3020Fax: 800.827.7111

Note: For use in non-vehicular traffic situations only. We do not recommend installation in concrete or asphalt. Weights and dimensions may vary slightly.

39 Carson ~ Products

Flush CoverMaterial: HDPEWeight: 3.0 lbs.Model: 1419-3 No Bolt 1419-3B Bolt DownSee OPTION SECTION: – Hinged Cover

T-CoverMaterial: HDPEWeight: 3.0 lbs.Model: 1419-4 No Bolt 1419-4B Bolt DownSee OPTION SECTION: – Meter reader cover

BodyMaterial: HDPEWeight: 7.0 lbs.Model: 1419-12See OPTION SECTION: – Slots

Colors AvailableGreen, Gray, Black, Tan or Violet

L Series1419-12Light Duty

1-5/8”(41 mm)

10-1/8”(257 mm)15-3/8”

(391 mm)

1-7/8”(48 mm)

11-3/4”(298 mm)16-7/8”

(429 mm)

12”(305 mm)17”

(432 mm)

16”(406 mm)

21”(533 mm)

19-1/2”(495 mm)

14-1/2”(368 mm)

12-1/4”(311 mm)

Pomona, CaliforniaToll-Free: 800.735.5566Phone: 909.634.3020Fax: 800.827.7111

Material ASTM TestProperty Method Typical Value1

Type, Class, Category D 1248 III, A, 3

Density, g/cm3 D 1505 0.950 min., not to exceed 0.965

Tensile Strength, at break, psi D 638 3,000 to 4,400

Elongation, at break, % D 638 400

Tensile Impact, ft-lb/in2 D 1822 27

Flexural Modulus, psi D 790 120,000 min., not to exceed 240,000

Low Temperature Brittleness, F50, at oC D 746 <-76

Hardness, Shore D D 2240 66

Deflection Temperature, at 66 psi, oF D 648 150o min., not to exceed 200o

Electrical Dielectric Strength, V/mil D 149 400 min., not to exceed 600

Molded Product2

Chemical Resistance D 543 Very Resistant

Water Absorption D 570 Less than 1% weight change

1The values listed for physical property measurements are nominal values only. Certain physical property measurements are subject to variations consistent with the test methods and are within a generally accepted range for such values. 2Test reports available on request.

Note: For use in non-vehicular traffic situations only. We do not recommend installation in concrete or asphalt. Weights and dimensions may vary slightly.

A

BC

©2008 Oldcastle Precast, Inc.

All information contained in this brochure was current at the time of printing. Because of Oldcastle Precast's policy of ongoing research and development, the Company reserves the right to discontinue or update product information without notice. 40Carson ~ Products

Static Vertical Load Rating(Design Load; Test Load)

ASTM C857 – A-0.3, 300 lbf/ft2; Report UltimateSCTE – Light Duty, Pedestrian; 3,000 lbf

Shipping Configuration

Unit, 78 assemblies, = 58.5 cu. ft., 860.0 lbs.

Shipping Information

L Series1419-12Light Duty

UNITDim. Description ValueA Height 53”B Length 40”C Width 48”

Units: 78 per palletWeight: 820 lbs. per pallet

FLUSH COVERDim. Description ValueA Height 50”B Length 40”C Width 48”


T-COVERDim. Description ValueA Height 56”B Length 40”C Width 48”


BODYDim. Description ValueA Height 53”B Length 40”C Width 48”


features • AllbrassconformstoAWWAStandardC800(ASTMB-62andASTMB-584, UNSNOC83600-85-5-5-5) • ApprovedtoANSI/NSFStandard61(2007a) • Add“-NL”toendofcatalognumberforitemtobeapprovedtoANSI/NSFStandard61and AnnexG(372).“NL”itemswillbemadefromUNS/CDANo.C89833alloy • Endsareintegralorsecuredwithadhesivetopreventunintentionaldisassembly • Holeforattachinghandleisprovidedintee-head • 300PSIworkingpressure • PadlockWingforlockingvalveinclosedposition • ConformstoAWWAC700forMeterthreads Note:Recommendedforinletsideshut-off Optional full 360° tee-head rotation.Insert“R”intopartnumber.Example:BA43-331Wr-G

GrIP JOINt fOr COPPer Or PLastIC tuBING (Cts) INLet By Meter sWIVeL Nut OutLet

Sturdystopsallow90°motionandareenclosedandprotected

PadlockWingforlockingvalveinclosedposition

Asnapringlocksthestemintothebodyofthevalve

Solidonepiecetee-headandstem

EPDMO-ringsinthestem

MoldedEPDMrubberseatsupportstheball.

Fluorocarbon-coatedbrassball.

Length

Height

the ford Meter Box Company, Inc. P.O.Box443,Wabash,IndianaU.S.A.46992-0443 Phone:260-563-3171/Fax:800-826-3487 OverseasFax:260-563-0167 http://www.fordmeterbox.com

SubmittedBy:

TheFordMeterBoxCompanyconsiderstheinformationinthissubmittalformtobecorrectatthetimeofpublication.Itemandoptionavailability,includingspecifications,aresubjecttochangewithoutnotice.Pleaseverifythatyourproductinformationiscurrent.

03/08/13

NylonWasher

GripJointNut

BeveledEPDMrubbergasketprovideshydraulicseal

PhosphorousBronzeGripperRingforaxialrestraint

angle Ball Meter Valves - (BA43-3xxW-G style)

suBMIttaL INfOrMatION

EPDMRubbermetergasketMeterCouplingThread

BronzeSnapRing

MeterSwivelNut

DrilledforSealWire

Outlet

Inlet

Note:Fordrecommendsusinginsertstiffenerswithplasticpipeortubing.

ValVe SizeSerVice line

Size inletMeter Size

Outletlength height

apprOx.Wt. lbS

partnuMber

✓ SubMittediteM(S)

3/4" 3/4" 5/8”x3/4”&3/4" 2-19/64" 1-7/8" 2.2 BA43-332W-G3/4" 3/4" 1" 1-63/64" 1-7/8" 2.4 BA43-334W-G3/4" 1" 5/8”x3/4”&3/4" 2-19/64" 2-7/32" 2.4 BA43-342W-G3/4" 1" 1" 1-63/64" 2-7/32" 2.5 BA43-344W-G

features • All brass conforms to AWWA Standard C800 (ASTM B-62 and ASTM B-584 UNS NO C83600 - 85-5-5-5) • Approved to ANSI/NSF Standard 61 (2007a) • Add “-NL” to end of catalog number for item to be approved to ANSI/NSF Standard 61 and Annex G (372). “NL” items will be made from UNS/CDA No. C89833 alloy • Padlock Wing for locking valve in closed position • Valve is non-directional and is watertight with flow in either direction • Ends are integral or secured with adhesive to prevent unintentional disassembly • Hole for attaching handle is provided in the tee-head • 300 PSI working pressure Optional full 360° tee-head rotation. Add “R” to end of part number.

female IrOn PIPe thread Inlet by meter sWIVel nut Outlet

Inlet

Length

ValVe SizeSerVice line

Size inletMeter Size

Outletlength

apprOx.Wt. lbS

part nuMber

SubMittediteM(S)

3/4" 3/4" 5/8" 3-15/16" 1.9 B13-331W3/4" 3/4" 5/8"x3/4" & 3/4" 3-1/2" 2.0 B13-332W3/4" 1" 5/8" 4-1/8" 2.1 B13-341W3/4" 1" 5/8"x3/4" & 3/4" 3-5/8" 2.2 B13-342W1" 1" 1" 3-15/16" 2.9 B13-444W1" 1-1/4" 1" 4-3/8" 3.1 B13-454W

Solid one piece tee-head and stem A restraining ring locks the stem into the body of the valve.

Padlock Wing

EPDM O-rings in the stem

Molded EPDM rubber seats support the ball.

EPDM Rubber Meter Gasket

Meter Coupling Thread

Bronze Snap Ring

Drilled for Seal Wire

Fluorocarbon-coated brass ball

Outlet

the ford meter box Company, Inc. P.O. Box 443, Wabash, Indiana U.S.A. 46992-0443 Phone: 260-563-3171 / Fax: 800-826-3487 Overseas Fax: 260-563-0167 http://www.fordmeterbox.com

Submitted By:

The Ford Meter Box Company considers the information in this submittal form to be correct at the time of publication. Item and option availability, including specifications, are subject to change without notice. Please verify that your product information is current.

03/13/13

straight ball meter Valves - (B13-xxxW style)

submIttal InfOrmatIOn

Female Iron Pipe Thread

Meter Swivel Nut

Sturdy stops allow 90° motion and are enclosed and protected

Pum

p an

d Irr

igat

ion

Phoenix, AZ Culloden, WV Houston, TX 877-623-9473 800-624-3572 800-231-9473

servicewire.com

Manufacturing quality. Delivering service.

81

UF / Type TWU600 Volt Copper

Description & Features:C(UL) listed Single Conductor Type UF/Type TWU is suitable for use as Sprinkler Irrigation Control Wire for general purpose lighting and power. Construction provides solid or stranded soft annealed copper conductor insulated with PVC that provides excellent abrasion, acid, chemical, oil and moisture resistance.•ULlistedTypeUF600Volt(#14thru4/0AWG)•C(UL)ListedTypeTWU600Volt(#14thru4/0AWG)•Directburialrated•Resistanttoacids,alkali,greaseandchemicals•Abrasion,crushandmoistureresistant

Applications:•Suitableforuseaspowerandcontrolconductorsforirrigation

systems•ForuseinaccordanceperNECArticle339

Specifications & Standards:UL 493; UL1581; RoHS CompliantFederal Spec AA-59544, CSA C22.2 No. 75

Construction:Conductors: Soft annealed copper Solid (18 AWG to 8 AWG) Stranded (6AWG to 4/0 AWG)Insulation: Thermoplastic PVCTemperature: 60°C Voltage: 600 Volts

Part Number ConductorAWG

Dimensions (inches) Standard Packaging Weight(Lbs./Mft.)Insulation O.D. 500' 1000' 2500'

ULE18 18 (solid) .045 .130 X X 13

ULE16 16 (solid) .045 .141 X X 15

UF14 14 (solid) .060 .184 X X 27

UF12 12 (solid) .060 .201 X X 36

UF10 10 (solid) .060 .272 X 50

UF8 8 (solid) .060 .303 X 81

UF6 6 (7 str) .060 .342 X 121

UF4 4 (7 str) .080 .389 X 176

UF2 2 (7 str) .080 .450 X 261

UF1/0 1/0 (19 str) .095 .557 Bulk 408

UF2/0 2/0 (19 str) .095 .602 Bulk 502

UF4/0 4/0 (19 str) .095 .715 Bulk 763

* UL Listed - UNDERGROUND LOW ENERGY 150 VOLT CIRCUIT CABLE SUNLIGHT RESISTANT. All values are nominal; all weights are exclusive of packaging. All diameters and weights are subject to normal manufacturing tolerances.

TYPE UF SINGLE CONDUCTOR

RD WE BE GN YW OE BN BK PE GY PK TN

Single cond. size 18 and 16 S S A A A A A S A A A A

Single cond. size 14 S S S S S S S S S S S S

Single cond. size 12 and 10 S S A S A A A S A A A A

Single cond. size 8 and larger A A A A A A A A A A A A

NOTE: S = Stock, A = AvailableAll sales are subject to Standard Terms & Conditions of Sale.

STANDARD COLORS

3M™ Direct Bury Splice Kit DBR/Y-6

Data Sheet May 2011

1 of 3 3

Applications The 3M™ Direct Bury Splice Kit DBR/Y-6 is used to electrically connect two or more pre–stripped copper wires and moisture seal the connection for direct burial. The kit includes a 3M™ Performance Plus Wire Connector R/Y+ and a high impact, UV-resistant polypropylene tube prefilled with moisture-resistant grease.

Agency Approvals & Self Certifications

C UL US Listed, UL Standard 486D, File No. E102356 Listed for use in wet, damp, direct bury and submersible locations with UF type cable. Meets European Standard EN 61984 Applicable ratings under this standard: IP68, Pollution Degree 3 RoHS 2002/95/EC

RoHS Compliant 2002/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless the substance is in an application that is exempt under RoHS. This information represents 3M’s knowledge and belief, which may be based in whole or in part on information provided by third party suppliers to 3M.

Maximum Voltage Rating: Application Temperature: Operating Temperature:

600 V 32°F to 120°F (0°C to 49°C) -40°F to 221°F (-40°C to 105°C)

Construction:

Specifications

Tube : Impact and UV Resistant Light Blue Polypropylene Dimensions: Length: 3.7in., Cover: 1.5in.x 1.1in., Diameter: 1in. Grease: 711B R/Y+ Connector: Steel Spring, Flame Retardant Insulator Wire Combinations Copper wire only Solid or Stranded *see chart for all combinations*

2 - 7 #18 1-3 #12 w/ 1 #18 2 - 6 #16 1-2 #10 w/ 1 #18 2 - 4 #14 1-3 #12 w/ 1 #16 2 - 4 #12 1-2 #10 w/ 1 #12 2 - 3 #10 1-2 #14 w/ 1 #18


2 of 3

Installation Instructions

1) ¾ in. 2)

3) 4) 5) 1) Strip insulation ¾ in. 2) With wire ends even, insert wires into the connector and tighten until secure. 3) Insert the connector all the way into the tube until the connector rests on the bottom. 4) Fold the wire into the channels. 5) Close the cap. Installation Tip: If having difficulty getting the twist-on connector down into the tube when using small gauge wires, use a thin non-conductive object to push the connector to the bottom of the tube. Upon removal of the object, ensure that no voids or water paths remain in the grease.

Warning Turn power off before installing or removing connector. All electrical work should be done according to appropriate electrical codes.


3 of 3

Combination Chart 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 41 2 3 41 2 3 41 2 31 2 3

1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 1 2 310

STR10

SOL14 STR 14 SOL 12 STR 12 SOL18 STR 18 SOL 16 STR 16 SOL

12 STR

12 SOL

10 STR

10 SOL

16 STR

16 SOL

14 STR

14 SOL

18 STR

18 SOL

Example:3 #14 SOL and1 #12 STR

Shelf Life & Storage

This product has a 5-year shelf life from date of manufacture when stored in a humidity controlled storage (10°C/50°F to 27°C/80°F and <75% relative humidity).

Availability From your local distributor; or from 3M.com/electrical [Where to Buy] or call 1.800.245.3573.

Important Notice All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the product, which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order, shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M.

Warranty; Limited Remedy; Limited Liability

This product will be free from defects in material and manufacture at the time of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted.

3M is a trademark of 3M Company.

3 Electrical Markets Division 6801 River Place Blvd. Austin, TX 78726-9000 800.245.3573 FAX: 800.245.0329 www.3M.com/electrical

Please recycle © 3M 2011 All rights reserved 78-8129-9255-6 B

1 of 2

3M™ Direct Bury Splice DBR/Y-6

Instructions 600 V Maximum Application Temperature 32°F - 120°F (0°C - 49°C) Maximum Operating Temperature 221°F (105°C)

UL Standard 486D, 3M File No E102356 For use in damp, wet, direct bury, and submersible locations

Meets European Standard EN 61984 Applicable ratings under this standard: IP68, Pollution Degree 3

Installation 1. Strip Insulation 3/4”. 2. With wire ends even, insert wires into the connector and tighten until secure. 3. Insert the connector all the way into the tube until the connector rests on the bottom. Note: If having difficulty getting the twist-on connector down into the tube when using small gauge wires, use a thin, non-conductive

object to push the connector to the bottom of the tube. Upon removal of the object, ensure that no voids or water paths remain in the grease.

February 2012 78-8129-9276-2 C

2 of 2

4. Fold the wires into the channels. 5. Close the cap. Common AWG Combinations

Copper Wire Only, Solid or Stranded* unless noted *See data sheet for all combinations.

No adverse health effects expected; for professional or industrial use only. Contains white mineral oil grease, CAS# 8042-47-5 3M is a trademark of 3M Company. Important Notice: All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the product, which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order, shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M. Warranty; Limited Remedy; Limited Liability: This product will be free from defects in material and manufacture at the time of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted.

3 Electrical Markets Division 6801 River Place Blvd. Austin, TX 78726-9000 800.245.3573 Please Recycle. Printed in USA. Fax 800.245.0329 © 3M 2012 All Rights Reserved. www.3M.com/electrical 78-8129-9276-2 C

2 – 7 #18 1 – 3 #12 w/ 1 #18

2 – 6 #16 1 – 2 #10 sol w/ 1 #18 str

2 – 4 #14 1 – 3 #12 w/ 1 #16

2 – 4 #14 1 – 2 #10 w/ 1 #12

2 – 3 #10 1 – 2 #14 w/ 1 #18

• Allows air to escapea pipeline as it isbeing filled

• Allows air to enter a pipeline as it is being emptied

• Allows accumulatingair to escape while aline is in operationand under pressure

• Meets AWWAC-512

• Compound leversystem

• NPT screwed or ANSIClass Flanges

Features Include

Valve Function

The Universal Air Valve is designed to permit the automaticescape of large quantities of air from a pipeline when the lineis being filled, and to permit air to enter the pipeline when the

line is being emptied. It also allows accumulating air to escapewhile the line is in operation and under pressure. This is accom-plished with a compound lever system functioning in conjunctionwith a large and small orifice in one integral body casting.

As the liquid rises into the valve, air escapes through the largeorifice to the atmosphere. Liquid entering the valve raises the floatand lever system, carrying with it the pressure plunger and themain valve.

When the liquid has raised the float to its limit, the stainlesssteel main valve rests against the seat. The pressure plunger alsorests against its seat, which is the main valve. In this position, thevalve is closed and no liquid can escape.

UL

SE

RIE

SUniversal Air Release Valves

Universal Air Release Valve

With Stainless Steel Trim or Bronze and Stainless Steel Trim

Air & Vacuum OrificePerformance Curves

Crispin Valve, 600 Fowler Ave., Berwick, PA 18603 • 1-800-AIR-VALV • T: (570) 752-4524 • F: (570) 752-4962 • WWW.CRISPINVALVE.COM • [email protected]

2

Operating ORIFICE SIZEPressure(PSIG) 3/32” 1/8” 5/32” 3/16” 1/4”

150 13.8 24.4 37.9 54.6 98200 17.9 31.9 49.5 72 127250 22.1 39.2 61.1 88 157300 26.4 46.7 73 105 187

Universal Air Release Valves

UL

SE

RIE

SUniversal Air Release Valve

Discharge in SCFM

Size of Valve 1” 2” 3” 4” 6” 8”Model No. UL10.1 UL20.1 UL30.1 UL40.1Screwed Inlet UL10 UL20 UL30 UL40

125# UL21.1 UL31.1 UL41.1Flanged Inlet UL21 UL31 UL41 C61 C81

250# UL22.1 UL32.1 UL42.1Flanged Inlet UL22 UL32 UL42 C62 C82

Model Information

6” and 8” Combination Valve Detail

Valve MAXIMUM OPERATING PRESSURE IN PSISize Max. 150 Max. 200 Max. 250 Max. 300

1” 3/16” 3/32” 3/32” 3/32”

2” 1/4” 3/16” 3/16” 1/8”

3” 1/4” 3/16” 3/16” 1/8”

4” 1/4” 3/16” 3/16” 1/8”

6” 1/4” 3/16” 3/16” 1/8”

8” 1/4” 3/16” 3/16” 1/8”

Orifice Sizing Information

If accumulating air risesinto the valve while theline is in operation andunder pressure, it will displace the liquid at thetop of the valve body andthe float will drop as theliquid recedes. As thisoccurs, the pressure valvewill open, permitting theescape of the accumulatedair, after which the liquidlevel will rise and thevalve will close.

Should the pipeline bedrained through naturalprocesses or should a largebreak develop, the floatwill drop all the way downas the liquid level drainsfrom the valve body. Thevalve will then stay in thefull open position permit-ting the entrance of airand eliminating the dan-ger of pipeline collapsedue to vacuum.

These cycles willrepeat automatically aseach condition presentsitself, and the valve willfunction satisfactorilywith hot or cold water,and in the presence ofmany chemicals and oil-base liquids.

Crispin Valve, 600 Fowler Ave., Berwick, PA 18603 • 1-800-AIR-VALV • T: (570) 752-4524 • F: (570) 752-4962 • WWW.CRISPINVALVE.COM • [email protected] UL

For 6” and 8” dimension and weight

information, see the following page.

3

UL

SE

RIE

SUniversal Air Release Valves

Universal Air Release ValveUniversal Valves

Parts List: 1”–4” Valves Dimensions and Weights

* The above parts are interchangeable at the customer’s request.

PART ITEM MATERIALNO.1P* PROTECTOP Cast Iron

1S* TOP Cast Iron

2 FLANGE Cast Iron

3* BODY, SCREWED Cast Iron

3F* BODY, 125 LB FLG. Cast Iron

3FH* BODY, 250 LB FLG Cast Iron

4 A&V FULCRUM Stainless Steel

5&16 PRESSURE FULCRUM Stainless Steel

6 VALVE LEVER Stainless Steel

7 LINK Stainless Steel

8 BALL LEVER Stainless Steel

9 BALL FLOAT Stainless Steel

10 BALL FULCRUM Stainless Steel

13 NUT Stainless Steel

14 PRESSURE VALVE Rubber/S/SPLUNGER

15 PRESSURE SEAT Stainless Steel

17 SEAT CAGE Stainless Steel

18 A&V SEAT Rubber

21 PRESS LIMIT STOP Stainless Steel

23 BEARING PIN Stainless Steel

23A BEARING PIN Stainless Steel



26 PIN CLIP Stainless Steel

28 SCREW Stainless Steel

29 DRAIN PLUG Steel

30 FULCRUM WASHER Fibre

31 FULCRUM WASHER Fibre

32 FLANGE GASKET Armstrong

33 FLANGE BOLT Steel

34 FLANGE NUT Steel

35 A&V FULCRUM NUT Steel

36 BALL FULCRUM NUT Steel

MODEL INLET TRIM HEIGHT WIDTH LENGTH WT(LBS)

UL10 1” NPT S/S 10 1/4” 6 7/8” 9 3/4” 27

UL10.1 1” NPT S/S/BRASS 10 1/4” 6 7/8” 9 3/4” 27

UL20 2” NPT S/S 13 1/2” 8 3/8” 12 3/8” 72

UL20.1 2” NPT S/S/BRASS 13 1/2” 8 3/8” 12 3/8” 72

UL21 2” 125# Flg. S/S 17” 8 3/8” 12 3/8” 74

UL21.1 2” 125# Flg. S/S/BRASS 17” 8 3/8” 12 3/8” 74

UL22 2” 250# Flg. S/S 17 1/4” 8 3/8” 12 3/8” 75

UL22.1 2” 250# Flg. S/S/BRASS 17 1/4” 8 3/8” 12 3/8” 75

UL30 3” NPT S/S 17 1/4” 10 1/4” 14 3/4” 111

UL30.1 3” NPT S/S/BRASS 17 1/4” 10 1/4” 14 3/4” 111

UL31 3” 125# Flg. S/S 20 5/8” 10 1/4” 14 3/4” 131

UL31.1 3” 125# Flg. S/S/BRASS 20 5/8” 10 1/4” 14 3/4” 131

UL32 3” 250# Flg. S/S 21” 10 1/4” 14 3/4” 133

UL32.1 3” 250# Flg. S/S/BRASS 21” 10 1/4” 14 3/4” 133

UL40 4” NPT S/S 20” 11 3/4” 16 3/4” 163

UL40.1 4” NPT S/S/BRASS 20” 11 3/4” 16 3/4” 163

UL41 4” 125# Flg. S/S 23” 11 3/4” 16 3/4” 180

UL41.1 4” 125# Flg. S/S/BRASS 23” 11 3/4” 16 3/4” 180

UL42 4” 250# Flg. S/S 23 5/16” 11 3/4” 16 3/4” 183

UL42.1 4” 250# Flg. S/S/BRASS 23 5/16” 11 3/4” 16 3/4” 183

C61 6” 125# Flg. S/S 16 1/4” 15” 22 7/8” 198

C62 6” 250# Flg. S/S 16 3/4” 15” 22 7/8” 222

C81 8” 125# Flg. S/S 18 1/8” 17 3/4” 25 3/8” 290

C82 8” 250# Flg. S/S 18 5/8” 17 3/4” 25 3/8” 320


4

ITEM DESCRIPTION MATERIAL ASTM1S TOP CAST IRON A126 CL.B2 FLANGE CAST IRON A126 CL.B3 BODY CAST IRON A126 CL.B

3W LOCK WASHER STAINLESS STEEL A2404 AIR & VAC FULCRUM STAINLESS STEEL A240

**6 VALVE LEVER STAINLESS STEEL A5827 LINK STAINLESS STEEL A2408 BALL LEVER STAINLESS STEEL A2409 FLOAT STAIN LESS STEEL A24010 BALL FULCRUM STAINLESS STEEL A58211 VALVE PLUNGER STAINLESS STEEL A193

& BUNA-N RUBBER12 PLUNGER NUT STAINLESS STEEL A19415 PRESSURE SEAT STAINLESS STEEL A58216 PRESSURE FULCRUM STAINLESS STEEL A24017 SEAT CAGE STAINLESS STEEL A24018 AIR & VAC SEAT BUNA—N RUBBER N/A23 BEARING PIN STAINLESS STEEL A582

23A BEARING PIN STAINLESS STEEL A58224 BEARING PIN STAINLESS STEEL A58225 BEARING PIN STAINLESS STEEL A58226 COTTER PIN STAINLESS STEEL A31329 DRAIN PLUG BRASS B50530 FULCRUM WASHER FIBER N/A32 FLANGE GASKET ARMSTRONG N—8092 N/A33 FLANGE BOLT STEEL A30734 NUT STEEL A56350 INTERFERENCE PIN STAINLESS STEEL A582

** Material for UL10.1 will be brass


Submittal Sheet for Crispin UL Series

SU

BM

ITTA

LS

HE

ET

FO

R U

LS

ER

IES

1” Universal Air Release ValveManufactured in compliance with ANSI/AWWA C512 Date: October, 2001

SpecificationsThe valve(s) shall be installed at the high points in the system orat points selected by the engineer. This will permit discharging thesurge of air from an empty line when filling, and relieve the vacu-um when draining the system. The valve(s) shall also release anaccumulation of air when the system is under pressure. This shallbe accomplished in a single valve body.

The valve(s) shall operate through a compound lever systemwhich will seal both the pressure orifice and the air and vacuumorifice simultaneously. This lever system shall permit a__________” orifice to release an accumulation of air from thevalve body at a capacity of ____________ SCFM of air and pres-sure of ____________ PSIG.

The function of the lever system shall also permit a positive dis-engagement of the main valve from the large orifice, as the floatdrops and pressure decreases. The disengagement shall beimmediate and not limited to the initial draw of a vacuum.

The valve(s) shall be Crispin Model ___________ Universal AirValve as manufactured by Multiplex Manufacturing Co., Berwick,PA. The valve(s) shall be ___________” NPT screwed or ANSIClass (125, 250) flanged inlet connection, and shall have a castiron body, top and inlet flange (where required), stainless steelfloat and trim with Buna-N seat. Valves which operate the pres-sure plunger via a single lever and fulcrum will not be acceptable.

Size SpecificationsMODEL INLET SIZE OUTLET SIZE A B WHT.UL10 1” NPT 1” NPT 9.75 10.75 27

UL10.1 1” NPT 1” NPT 9.75 10.75 27

Orifice OptionsDIAMETER MAX. PRESSURE FLOW RATE

3/16 150 PSIG 54.6 SCFM3/32 300 PSIG 26.4 SCFM

A

B

5025 15 17 43430

32

2

36

9

2512 23 16

23A

3W87

24

25

25

10

15 18

30 11

34

34

33

Parts List

Option: A protectop will be supplied to prevent debris from entering the outlet of the valve.

Option: (Where pressures are greater than 300 PSIG), the valve(s) shall be ANSI Class ____________ flanged inlet connection, and shallhave a (steel, stainless steel, or ductile iron) body, top and inlet flange.

Standard operating pressure for Crispin Air Valves is 20 to 150 PSIG. Please check one of the following if your operating needs differ:____ 2 to 40 PSIG ____ 151 to 300 PSIG

5

ITEM DESCRIPTION MATERIAL ASTM1S TOP CAST IRON A126 CL.B2 FLANGE CAST IRON A126 CL.B3 BODY CAST IRON A126 CL.B

4A CAP SCREW STAINLESS STEEL A1935B AIR & VAC FULCRUM STAINLESS STEEL A240**6 VALVE LEVER STAINLESS STEEL A5827 LINK STAINLESS STEEL A2408 BALL LEVER STAINLESS STEEL A2409 FLOAT STAINLESS STEEL A240

9A FLOAT ROD STAINLESS STEEL A58210 BALL FULCRUM STAINLESS STEEL A58211 VALVE PLUNGER STAINLESS STEEL A193

& BUNA-N RUBBER12 PLUNGER NUT STAINLESS STEEL A194

13W LOCK WASHER STAINLESS STEEL A24015 PRESSURE SEAT STAINLESS STEEL A58216 PRESSURE FULCRUM STAINLESS STEEL A24017 SEAT CAGE STAINLESS STEEL A24018 AIR & VAC SEAT BUNA—N RUBBER N/A21 PRESSURE LIMIT STOP STAINLESS STEEL A24023 BEARING PIN STAINLESS STEEL A582

23A BEARING PIN STAINLESS STEEL A58223B BEARING PIN STAINLESS STEEL A58224 BEARING PIN STAINLESS STEEL A58225 BEARING PIN STAINLESS STEEL A58226 COTTER PIN STAINLESS STEEL A31329 DRAIN PLUG BRASS B50530 FULCRUM WASHER FIBER D71032 FLANGE GASKET ARMSTRONG N—8092 N/A33 FLANGE BOLT STEEL A30734 NUT STEEL A56336 BALL FULCRUM NUT STEEL A56350 INTERFERENCE PIN STAINLESS STEEL A582

CP1 NIPPLE STEEL A53CP2 COMPANION FLANGE CAST IRON A126 CL. B



SU

BM

ITTA

LS

HE

ET

FO

R U

LS

ER

IES

2” Universal Air Release ValveManufactured in compliance with ANSI/AWWA C512 Date: October, 2001

SpecificationsThe valve(s) shall be installed at the high points in the system or at pointsselected by the engineer. This will permit discharging the surge of air froman empty line when filling, and relieve the vacuum when draining the sys-tem. The valve(s) shall also release an accumulation of air when the sys-tem is under pressure. This shall be accomplished in a single valve body.

The valve(s) shall operated through a compound lever system whichwill seal both the pressure orifice and the air and vacuum orifice simul-taneously. This lever system shall permit a __________” orifice torelease an accumulation of air from the valve body at a capacity of____________ SCFM of air and pressure of ____________ PSIG.

The function of the lever system shall also permit a positive disen-gagement of the main valve from the large orifice, as the float drops andpressure decreases. The disengagement shall be immediate and notlimited to the initial draw of a vacuum.

The valve(s) shall be Crispin Model ________ Universal Air Valve as man-ufactured by Multiplex Manufacturing Co., Berwick, PA. The valve(s) shallbe _______” NPT screwed or ANSI Class (125, 250) flanged inlet connec-tion, and shall have a cast iron body, top and inlet flange (where required),stainless steel float and trim with Buna-N seat. Valves which operate thepressure plunger via a single lever and fulcrum will not be acceptable.

Option: A protectop will be supplied to prevent debris from entering theoutlet of the valve.

Option: (Where pressures are greater than 300 PSIG), the valve(s) shallbe ANSI Class ____________ flanged inlet connection, and shall have a(steel, stainless steel, or ductile iron) body, top and inlet flange.

All Crispin Valves are hydrostatically tested at 150% of their maximumworking pressure. Standard operating pressure for Crispin Air Valves is20 to 150 PSIG. Please check one of the following if your operatingneeds differ: ____ 2 to 40 PSIG ____ 151 to 300 PSIG

Orifice OptionsDIAMETER MAX. PRESSURE DISCHARGE RATE

1/4” 150 PSIG 98 SCFM3/16” 250 PSIG 88 SCFM1/8” 300 PSIG 46.7 SCFM

A1S10

3426

321

24

2625

23

5018 2

16

1517

324A

5B

23B23B

13W

9A9

23B8

3633

BC

29

CP1

CP2 Parts List

Size SpecificationsMODEL INLET SIZE OUTLET SIZE A B C WHT.UL20 2” NPT 2” NPT 12.50 13.50 72

UL20.1 2” NPT 2” NPT 12.50 13.50 72*UL21 2” 125# FLG 2” NPT 12.50 17.00 78UL21.1 2” 125# FLG 2” NPT 12.50 17.00 78UL22 2” 250# FLG 2” NPT 12.50 17.25 89

UL22.1 2” 250# FLG 2” NPT 12.50 17.25 89

* Includes ANSI Class 125 or 250 Companion FLG and NPL

30

7 11

6

12

FLANGE CONNECTION PARTS

** Material for UL2_.1 will be brass6

ITEM DESCRIPTION MATERIAL ASTM1S TOP CAST IRON A126 CLB2 FLANGE CAST IRON A126 CLB3 BODY CAST IRON A126 CLB4 AIR/VAC FULCRUM STAINLESS STEEL A240

4A FULCRUM BOLT STAINLESS STEEL A1935 PRESSURE FULCRUM STAINLESS STEEL A240

**6 VALVE LEVER STAINLESS STEEL A5827 LINK STAINLESS STEEL A2408 BALL LEVER STAINLESS STEEL A2409 FLOAT STAINLESS STEEL A240

9A FLOAT ROD STAINLESS STEEL A58210 BALL FULCRUM STAINLESS STEEL A58211 VALVE PLUNGER STAINLESS STEEL& A193/D2000

BUNA-N RUBBER 12 PLUNGER NUT STAINLESS STEEL A19413W LOCK WASHER STAINLESS STEEL A24015 PRESSURE SEAT STAINLESS STEEL A58217 SEAT CAGE STAINLESS STEEL A24018 AIR & VAC SEAT BUNA-N RUBBER D200021 PRESSURE LIMIT STOP STAINLESS STEEL A24023 BEARING PIN STAINLESS STEEL A582

23A BEARING PIN STAINLESS STEEL A58224 BEARING PIN STAINLESS STEEL A58225 BEARING PIN STAINLESS STEEL A58226 COTTER PIN STAINLESS STEEL A31329 DRAIN PLUG BRASS B50530 FULCRUM WASHER FIBER D71031 FULCRUM WASHER FIBER D710

31A FULCRUM WASHER FIBER D71032 FLANGE GASKET ARMSTRONG N-8092 N/A33 FLANGE BOLT STEEL A30734 NUT STEEL A56335 AIR/VAC FULCRUM NUT STEEL A56336 BALL FULCRUMNUT STEEL A56337 ADJUSTING PLATE STAINLESS STEEL A24038 BOLT STAINLESS STEEL A19350 INTERFERENCE PIN STAINLESS STEEL A582

** Material for UL30.1, UL.31.1, UL40.1, UL41.1, UL42.1 will be brass



SU

BM

ITTA

LS

HE

ET

FO

R U

LS

ER

IES

3”–4” Universal Air Release ValveManufactured in compliance with ANSI/AWWA C512 Date: October, 2001

Specifications

Orifice OptionsDIAMETER MAX. PRESSURE DISCHARGE RATE

1/4” 150 PSIG 98 SCFM3/16” 250 PSIG 88 SCFM1/8” 300 PSIG 46.7 SCFM

Parts List

Size SpecificationsMODEL INLET SIZE OUTLET SIZE A B C WHT.UL30 3”NPT 3” NPT 14.75 18.00 114UL31 3” 125# FLG 3” NPT 14.75 20.50 125UL32 3” 250# FLG 3” NPT 14.75 21.00 131

UL30.1 3” NPT 3” NPT 14.75 18.00 114UL31.1 3” 125# FLG 3” NPT 14.75 20.50 125UL32.1 3” 250# FLG 3” NPT 14.75 21.00 131UL40 4” NPT 4” NPT 16.75 20.00 162UL41 4” 125# FLG 4” NPT 16.75 23.00 177UL42 4” 250# FLG 4” NPT 16.75 23.25 188

UL40.1 4” NPT 4” NPT 16.75 20.00 162UL41.1 4” 125# FLG 4” NPT 16.75 23.00 177UL42.1 4” 250# FLG 4” NPT 16.75 23.25 188

The valve(s) shall be installed at the high points in the system or at pointsselected by the engineer. This will permit discharging the surge of air froman empty line when filling, and relieve the vacuum when draining the sys-tem. The valve(s) shall also release an accumulation of air when the sys-tem is under pressure. This shall be accomplished in a single valve body.

The valve(s) shall operate through a compound lever system which willseal both the pressure orifice and the air and vacuum orifice simultane-ously. This lever system shall permit a __________” orifice to release anaccumulation of air from the valve body at a capacity of ____________SCFM of air and pressure of ____________ PSIG.

The function of the lever system shall also permit a positive disengage-ment of the main valve from the large orifice, as the float drops and pres-sure decreases. The disengagement shall be immediate and not limitedto the initial draw of a vacuum.

The valve(s) shall be Crispin Model ___________ Universal Air Valve asmanufactured by Crispin-Multiplex Manufacturing Co., Berwick, PA. Thevalve(s) shall be ___________” NPT screwed or ANSI Class (125, 250)flanged inlet connection, and shall have a cast iron body, top and inletflange (where required), stainless steel float and trim with Buna-N seat.Valves which operate the pressure plunger via a single lever and fulcrumwill not be acceptable.

Option: A protectop will be supplied to prevent debris from entering theoutlet of the valve.

Option: (Where pressures are greater than 300 PSIG), the valve(s) shallbe ANSI Class ____________ flanged inlet connection, and shall have a(steel, stainless steel, or ductile iron) body, top and inlet flange.

Standard operating pressure for Crispin Air Valves is 20 to 150 PSIG.Please check one of the following if your operating needs differ:

____ 2 to 40 PSIG ____ 151 to 300 PSIG

A1S 35

32

503633

2413W

12

9A2321

2317

7

34

3010

25

21

2

3

1815

37384A4

23A255

31A31

9

8

29B

C

7

FEATURES • All brass conforms to AWWA Standard C800 (ASTM B-62 and ASTM B-584, UNS NO C83600 - 85-5-5-5) • Add “-NL” to end of catalog number for item to be approved to ANSI/NSF Standard 61 and Annex G (372). “NL” items will be made from UNS/CDA No. C89833 alloy • Valve is non-directional and is watertight with flow in either direction • Ends are integral or secured with adhesive to prevent unintentional disassembly • Hole for attaching curb box rod or handle is provided in tee-head • 300 PSI working pressure Optional Padlock Wing for locking valve in closed position. Add “W” to part number Optional full 360° tee-head rotation. Add “R” to part number.

FEMALE IRON PIPE THREAD INLET BY FEMALE IRON PIPE THREAD OUTLET

Inlet

Length

VALVE SIZE INLET SIZE OUTLET SIZE LENGTHAPPROX.WT. LBS

PARTNUMBER

✓ SUBMITTEDITEM(S)

3/4" 3/4" 3/4" 3-3/8" 1.9 ▼ B11-3333/4" 1" 3/4" 3-9/16" 2.0 ▼ B11-3433/4" 1" 1" 3-11/16" 2.1 ▼ B11-3443/4" 1" 1" 4-1/2" 2.3 ▼ BL11-344-4.51" 1" 1" 3-13/16" 2.5 ▼ B11-4441" 1-1/4" 1" 4-3/16" 2.9 ▼ B11-4541" 1-1/4" 1-1/4" 4-7/16" 3.1 ▼ B11-455

1-1/2" 2" 1-1/2" 5" 6.4 B11-6761-1/2" 2" 2" 5-1/4" 8.0 B11-677

2" 2" 2" 5-45/64" 9.2 B11-778

Solid one piece tee-head and stem

Sturdy stops allow 90° motion and are enclosed and protected

A restraining ring locks the stem into the body of the valve

EPDM O-rings in the stem

Female Iron Pipe ThreadFemale Iron Pipe Thread

Molded EPDM rubber seats support the ball.

Fluorocarbon-coated brass ball

Outlet

The Ford Meter Box Company, Inc. P.O. Box 443, Wabash, Indiana U.S.A. 46992-0443 Phone: 260-563-3171 / Fax: 800-826-3487 Overseas Fax: 260-563-0167 http://www.fordmeterbox.com

Submitted By:


05/14/13

Ball Valve Curb Stop - (B11-xxx style)

SUBMITTAL INFORMATION

▼ Approved to ANSI/NSF Standard 61-2007a.

FEATURES

• All brass conforms to AWWA Standard C800 (ASTM B-62 and B-584, UNS NO C83600 - 85-5-5-5) • Add “-NL” to end of catalog number for item to be approved to ANSI/NSF Standard 61 and Annex G (372). “NL” items will be made from UNS/CDA No. C89833 alloy. • Body design provides larger, more rugged wrench flats for proper installation

MALE IRON PIPE BY PACK JOINT FOR COPPER OR PLASTIC TUBING (CTS)

Pack Joint NutBeveled EPDM rubber gasket provides hydraulic seal

Integral clamp contains machined grooves for axial restraint

Male Iron Pipe Threads

Stainless steel screw activates clamp

Anti-friction ring

MIP Size

Length

DESCRIPTION LENGTHAPPROX.WT. LBS

PARTNUMBER

✓ SUBMITTEDITEM(S)MALE IRON PIPE P.J. FOR CTS

1/2" 1/2" 2" .5 ▼▼ C84-111/2" 5/8" 2-1/16" .8 ▼▼ C84-121/2" 3/4" 2-1/16" .8 ▼▼ C84-133/4" 1/2" 2" .8 ▼▼ C84-313/4" 5/8" - .7 ▼▼ C84-323/4" 3/4" 2-1/4" .6 ▼▼ C84-333/4" 1" 2-3/8" .7 ▼▼ C84-341" 5/8" - - ▼▼ C84-421" 3/4" 2-3/8" .7 ▼▼ C84-431" 1" 2-9/16" .8 ▼▼ C84-441" 1-1/4" 2-1/2" 1.2 C84-451" 1-1/2" 2-9/16" 1.8 C84-46

1-1/4" 1" 2-9/16" 1.4 C84-541-1/4" 1-1/4" 2-9/16" 1.4 C84-551-1/4" 1-1/2" 3-1/4" 1.8 C84-561-1/2" 1-1/2" 3-1/4" 2.0 C84-661-1/2" 2" 2-15/16" 2.6 C84-67

2" 2" 3-1/4" 3.1 C84-77

The Ford Meter Box Company, Inc. P.O. Box 443, Wabash, Indiana U.S.A. 46992-0443 Phone: 260-563-3171 / Fax: 800-826-3487 Overseas Fax: 260-563-0167 http://www.fordmeterbox.com

Submitted By:


02/05/13

PJ Size

Pack Joint Coupling - (C84-xx style)

SUBMITTAL INFORMATION

▼ Approved to ANSI/NSF Standard 61-2007a.Note: Ford recommends using insert stiffeners with plastic pipe or tubing.