CONSILIUM 91240-001000 CS4000 user manual E1 04 2 E

7/25/2019 CONSILIUM 91240-001000 CS4000 user manual E1 04 2 E

1/40

Fire Alarm SystemCS4000

User Guide

Consilium


2/40

The contents of this document are subject to revision without notice due tocontinued progress in methodology, design and manufacturing. ConsiliumMarine assumes no legal responsibility for any error or damage resulting fromthe usage of this document.

Consilium Marine AB

P.O. Box 8763SE-402 76 GTEBORGSWEDENTel: +46-31-710 77 00, Fax: +46-31-710 78 00E-mail: [email protected]: www.consilium.se

FirstEdition, August 25,2004Document number S-4-010.965/EPart no: 91240-001000

2004 Consilium Marine AB


3/40

User Guide Contents 1

Salwico CS4000

Contents

About this manual .................................................................................................................... 3

Chapter 1: General description .............................................................................................. 4

Control panel CS4000 ............................................................................................................ 4

Description of keys and indicators ..................................................................................... 4

Repeater panel CS4000 .......................................................................................................... 8

Description of keys and indicators ..................................................................................... 8

Guide to the menu system.................................................................................................... 10

Choosing menu alternatives ............................................................................................. 10

Menu tree CS4000............................................................................................................11

Explanation of the different menu alternatives ................................................................ 12

Definition of terms ...............................................................................................................16

CS4000 System data............................................................................................................. 17CS4000 System : EN54 functions ........................................................................................18

Optional functions with requirements .............................................................................. 18

Functions relating to other parts of the EN54 standard.................................................... 18

Ancillary functions not required by EN54 ....................................................................... 18

Chapter 2: Operations ........................................................................................................... 19

Access levels ........................................................................................................................ 19

Description of the access levels........................................................................................ 20

Login .................................................................................................................................... 20

Users..................................................................................................................................... 20

Add new user .................................................................................................................... 20Delete user........................................................................................................................ 20

Pre-alarm .............................................................................................................................. 21Fire alarm ............................................................................................................................. 22

When Fire is flashing.................................................................................................... 22

Information displayed ...................................................................................................... 22

Mute ................................................................................................................................. 22

Reset ................................................................................................................................. 23

Several alarms .................................................................................................................. 23

Type of fire alarms from conventional zones................................................................... 23

Fault indications ................................................................................................................... 24

When Fault is flashing .................................................................................................. 24Information displayed ...................................................................................................... 24

Mute ................................................................................................................................. 24

Reset ................................................................................................................................. 25

Fault messages...................................................................................................................... 25

Disconnections ..................................................................................................................... 26

Disconnections available .................................................................................................. 26

Acknowledgement of a new disconnection...................................................................... 26

Disconnecting zones......................................................................................................... 27

Disconnecting addressable detectors................................................................................ 28

Disconnecting alarm devices (bells etc)........................................................................... 28

Disconnection of alarm delay........................................................................................... 28Disconnecting external outputs (for example fans, fire doors etc) .................................. 29


4/40

User Guide Contents 2

Salwico CS4000

Disconnection of alarm transfer output............................................................................ 29

Reconnection of disconnected items .................................................................................... 29

Chapter 3: Installation........................................................................................................... 30

Electrical connection ............................................................................................................ 30

Description of CS4000 PCBs.......................................................................................... 30

Connection ....................................................................................................................... 31

Testing .................................................................................................................................. 32

Test a fire-detecting zone ................................................................................................. 32

Reset test mode................................................................................................................. 32

Test the control unit display ............................................................................................. 32

Appendix A Fault codes & Fuses .......................................................................................... 33

Fault list ................................................................................................................................ 33

Fuses..................................................................................................................................... 36

Fuse list ............................................................................................................................ 36

Fuse locations on base board, BB. ................................................................................... 36

Fuse locations on rectifier board, RB. .............................................................................. 36

Index ........................................................................................................................................ 37


5/40

User Guide About this manual 3

Salwico CS4000

About this manual

This manual gives general information about the CS4000 fire alarm

system and its control panel in chapter 1 General description.

In chapter2 Operation it is described how to operate the CS4000 fire

alarm system.

It also gives a brief instruction how to connect and test the CS4000 fire

alarm system in chapter 3 Installation. For more detailed information,

see the separate CS4000 Installation manual.

In appendix A you will find detailed information about the fault codes

that can appear and where the fuses are located.

If nothing else, please read Guide to the menu system in chapter 1 to

get a basic understanding how to operate the system.


6/40

User Guide Chapter 1: General description 4

Salwico CS4000

Chapter 1: General description

The CS4000 is a state of the art analogue addressable fire detection

system designed to meet all major marine and industrial requirements.Special care has been taken to ergonomics, user friendliness with its

logical self-instructing operator panel guiding the user to the various

functions available.

The CS4000 can be delivered with either analogue addressable or

conventional detectors or a combination of both in the same system.

Control panel CS4000

The control panel is used to monitor and control all functions of the

CS4000 fire alarm system. The CS4000 is a menu-operated system and

instructions are given in the text display making it very easy to use.

0System Fault

Home Disc.

Test

Alarm Device

Power

Alarm Transfer

Alarm Delay

Zone/Unit

2

Warning

OK

Pre-Alarm

Menu

Reset

FAULT DISC.

NextMute

OK

ABC3

DEF' '1

5JKL

6MNOGHI

4

8TUV

9WXYZPQRS

7

F1

F2

F3

FIRE

Description of keys and indicators

18

1920

21

22

23

24

25

1

23

4

5

6

7

8

9

10

11

12

13

14

15

16

17


7/40


Salwico CS4000

1. Fire alarm indicator

The fire alarm indication is flashing with red light to indicate that there

is an un-muted fire alarm in the system. It turns into steady light when

all fire alarms are muted.

2. Disconnection indicator

This is a general indicator showing that there is at least one

disconnected function in the system, for example a zone, detector,

external control or alarm device.

3. Fault indicator

The fault indication is flashing with yellow light to indicate that there is

an un-muted fault in the system. It turns into steady light when all fault

alarms are muted.

4. Power indicatorIndicates with green steady light that the power supply to the control

panel is OK.

5. Test indicator

Indicates with yellow steady light that there is at least one zone in test

mode. If the indication is flashing the control panel has not been

initiated at start up of the system.

6. Alarm transfer indicator (only industrial application)

Indicates with yellow steady light that the output controlling the

transmission of fire alarms to the fire brigade has been activated. The

indication starts flashing if there is a fault detected on the alarm transfer

output.

7. Alarm device indicator

Indicates with yellow steady light that an alarm device output (bells

etc) is disconnected. Flashing light indicates that there is a fault on an

alarm device output.

8. Alarm delay indicator

Indicates with yellow steady light that the outputs for alarm devices(bells) or alarm transfer (industrial application) are delayed.

9. Zone/Unit indicator

Indicates with yellow steady light that a fire detector or zone is

disconnected. Flashing yellow indicates that at least one fire detector or

zone is in fault condition.

10. System fault indicator

Flashes with yellow light to indicate an internal fault in the control

panel or when there is a fault on the system communication of type no

poll. See appendix A Fault codes for more information.


8/40


Salwico CS4000

11. Warning indicator

Warnings, for example a dirty detector, are indicated with yellow

steady light.

12. Pre-alarm indicator

The pre-alarm indication flashes with red light to indicate that there isan un-muted pre-alarm in the system. It turns into steady light when all

pre-alarms are muted.

13. Custom keys and indicators

The three custom keys with yellow indicators are programmable to

customer-specific functions. The functions of these buttons and

indicators are programmed via the definition program.

14. Fields for custom text

The function of each custom key can be described in these text fields

using user-defined inserts in the panel slots.

15. Mute button

This button is used to mute and silence alarms.

16. More alarms

Flashes with red light if there is more than one fire alarm in the system.

17. Next button

Press Next button to scroll through the different alarms. The list always

returns to the first fire alarm after 20 seconds if no buttons are pressed.

18. Menu shortcut button

This button gives direct access to the main menu, where all the

functions of the CS4000 system can be accessed.

19. Home shortcut button

This button gives direct access to the initial view.

20. Disconnections shortcut button

This button gives direct access to the disconnections menu, from where

disconnections can be made.

21. Alphanumerical display

The blue alphanumerical display has a capacity of 14x40 characters.

22. Numerical keypad

The numerical keypad is used to enter information into the system.

The button erases one character at the time.

23 OK buttons

The OK buttons are used to select a menu alternative or to accept a

function.


9/40


Salwico CS4000

24. Arrow keys

The arrow keys are used to navigate in the menus and select different

menu alternatives.

OKGo to previous menu.Selects the chosen menu

alternative.

Shows next item in the list. If thelast item is displayed it will go to

the first item.

Shows the previous item in the list. Ifthe first item is displayed it will go to

the last item.

25. Reset button

This button is used to reset different alarms from the system.


10/40


Salwico CS4000

Repeater panel CS4000

The repeater panel is used to monitor functions of the CS4000 fire

alarm system. It is possible to view and list fire alarm, faults anddisconnections.

Description of keys and indicators

1. Fire alarm indicator

The fire alarm indication is flashing with red light to indicate that there

is an un-muted fire alarm in the system. It turns into steady light when

all fire alarms are muted from the main control panel.

2. Power indicator

Indicates with green steady light that the power supply to the repeater

panel is OK.

Power

Mute

FIRE

FaultTest Fire Disc.

Fault

Disconnection

Scroll

9

10

11

1

2

3

4

5

6

7

8

3. Fault indicator

The fault indication is flashing with yellow light to indicate that there is

an un-muted fault in the system. It turns into steady light when all fault

alarms are muted from the main control panel.


11/40


Salwico CS4000

4. Disconnection indicator

This is a general indicator showing that there is at least one

disconnected function in the system, for example a zone, detector,

external control or alarm device.

5. Test button

Test of all indications and each segment in the alphanumerical display

on the repeater panel.

6. Fire button

Gives direct access to the fire alarm list.

7. Fault button

Gives direct access to the fault list.

8. Disc. buttonGives direct access to the disconnection list.

9. Alphanumerical display

The blue alphanumerical display has a capacity of 14x40 characters.

10. Scroll buttons

Used to scroll up and down in the different lists.

11. Mute buttons

Mutes the local buzzer.


12/40


Salwico CS4000

Guide to the menu system

The CS4000 is a menu-operated system. All functions in the system

can be reached from the different menus.

Choosing menu alternatives

Press Menu to enter the menu system. Navigate in the menu

alternatives with the up and down arrows. Choose a menu alternative

with the right arrow and go to previous menu with the left arrow.

It is also possible to choose a menu alternative by entering the menu

number.

In the lower part of the alphanumerical display the different options

available for each individual menu are shown.

The numerical keypad is used to entering information, for example

zone and detector number.

The button erases the last alphanumeric entry.

OK

Show the previous item in the list. If

the first item is displayed it will go tothe last item.

Go to previous menu.Selects the chosen menu

alternative.

Show next item in the list. If thelast item is displayed it will go to

the first item.


13/40


Salwico CS4000

Menu tree CS4000

Home1 Fault Alarms

1 Fault List2 Warning List

3 Reset All Faults

2 Fire Alarms1 Fire List

2 Pre-Alarm List

3 Resound (restart bells)

4 Reset All Fire Alarms

3 Disconnections1 New disconnection (access level 2B)

1 Zones

2 Detectors & Manual Call Points

3 External Controls

1 All External Controls2 Alarm Transfer

4 External Alarms

1 Alarm Device (Bells etc.)

2 Alarm Delay

5 Test Mode

2 Disconnection list

3 Periodic Disconnection list

4 Old Disconnections

5 Remove all disconnections

4 Login1 Login

2 New User (access level 4)

3 Delete User (access level 4)

5 Settings1 Set Dimmer

2 Set Time

3 Set Date

4 Test display

5 Alarm delay time (access level 3)

6. Keyboard beep

6 Service menu (access level 4)1 System Details

2 System Boards

3 Display Units

4 Zones5 Loops

6 Reload Configuration

7 History1 Fire History List2 Fault History List

3 Disconnection History List

4 Common History List


14/40


Salwico CS4000

Explanation of the different menu alternatives

HomeTop-level start display showing CS4000 FIRE ALARM SYSTEM

and the name of the installation (if defined).

1 Fault Alarms

The menu from which fault- and warning messages are listed and

handled.

Fault List

Shows all present fault messages

Warning ListShows all present warning messages, for instance a dirty detector or an

open door on a central unit.

1.3 Reset All Faults

Reset all present faults in the fault list (1.1).

2 Fire Alarms

The menu from which fire- and pre-alarms are listed and handled. Also

possibility to re-activate alarm devices that has been muted (re-sound).

2.1 Fire List

Shows all present fire alarms.

2.2 Pre-Alarm List

Shows all present pre-alarms.

2.3 Resound (restart bells)

If the alarm devices has been silenced by pressing Mute, this function

will restart them if the fire alarm has not been reset.

2.4 Reset All Fire AlarmsResets all fire alarms in the fire list (2.1)

3 Disconnections

The menu, from which disconnections of parts of the fire alarm system

are added, removed or listed.

3.1 New disconnection (access level 2B)

Adds new disconnections.

3.1.1 Zones

Possibility to disconnect entire zones for a specified time period orpermanent.


15/40


Salwico CS4000

3.1.2 Detectors & Manual Call Points

Possibility to disconnect individual detectors or manual call points for a

specified time period or permanent.

3.1.3 External Controls

Possibility to de-activate all External Controls or Alarm Transfer.

3.1.3.1 All External Controls

Disconnects all outputs to external controls. This means that an alarm

condition will not cause any doors to close, fans to stop etc.

3.1.3.2 Alarm Transfer

Disconnects the supervised output for alarm transfer, normally used in

on-shore installations to alert the fire brigade in case of a fire alarm.

3.1.4 External Alarms

Disconnects outputs to external alarm or activates alarm delay.

3.1.4.1 Alarm Device (Bells etc.)

Disconnects outputs for alarm devices, such as audible- (bells etc) and

optical alarm devices.

3.1.4.2 Alarm Delay

Activates the programmable alarm delay time. When alarm delay is

activated there is a delay time between when a fire is detected until the

alarm device outputs are activated.

3.1.5 Test Mode

Possibility to set a zone into test mode. See chapter 3 Installation under

testing for more details.

3.2 Disconnection list

Shows all active disconnections in the system. A periodic disconnection

(3.3) that is not active will not be shown in this list. Reconnection of a

disconnected unit is made from this list. See chapter 2 Operations under

reconnection of disconnected items for more details.

3.3 Periodic Disconnection list

Shows all periodic disconnections in the system. Removal of periodic

disconnections is made from this list.

3.4 Old Disconnections

A list showing the 150 latest, previous removed, disconnections. This

list also gives the possibility to re-activate an old disconnection again.

This function is very useful if the same disconnection is frequently

needed during irregular time periods. Just mark the appropriate old

disconnection in the list and press 0 to re-activate it.


16/40


Salwico CS4000

3.5 Remove all disconnections

Removes all active disconnections shown in the disconnection list (3.2).

Does not remove periodic disconnections (3.3) permanently, just the

active period of the periodic disconnection.

4 Login

From this menu it is possible to log in to the system by entering the

access code, create new users or delete users.

4.1 Login

Login is made from this menu. Enter the personal access code. For

further details see chapter 2 Operations under login.

4.2 New User (access level 4)

Use this menu to create new users. Access level 4 is required to be ableto create new users.

4.3 Delete User (access level 4)

Use this menu to delete user from the system. Access level 4 is required

to be able to delete users.

5 Settings

Use this menu to adjust parameters in the system such as dimmer level

on control panel, date and time and alarm delay time. It is also possible

to make a lamp test for the control panel under test display (5.4).

5.1 Set Dimmer

Use this menu to adjust the contrast level on the control panel display

between 1-9.

5.2 Set Time

Use this menu to set the system time.

5.3 Set Date

Use this menu to set the system date.

5.4 Test display

From this menu it is possible to activate a lamp test to verify the correct

function of the alphanumerical display and for all indications on the

control panel.

5.5 Alarm delay time (access level 3)

Use this menu to adjust the programmable alarm delay time between 1

to 10 minutes.

5.6 Keyboard beep

Use this menu to turn the keyboard beep ON or OFF.


17/40


Salwico CS4000

6 Service menuUse this menu to list and view information about the system and itscomponents. It is also possible to make disconnections of the listed units.

6.1 System DetailsThis menu gives information about the installed system such as name andreference number (if defined). It also lists when the system was last configuredand by which program.

6.2 System BoardsUse this menu to list and view information about the installed system PCBs.

It is possible to view all details about the boards such as installed detectorloops, program versions installed, status of inputs and outputs and to print the

listed information.6.3 Display Units

Use this menu to list information about the installed control and repeaterpanels and how they are configured.

6.4 ZonesThis menu shows a list of all zones configured in the system. It is possible to

list all loop units in a zone if it consists of addressable loop units. It is alsopossible to make disconnections of zones or loop units and to set a single firedetector in alarm condition.

6.5 LoopsThis menu shows a list of all the physical loops installed in the system. A loopcan consist of conventional or addressable fire alarm detectors or other loopunits. It is also possible to make disconnections of entire loops.

6.6 Reload ConfigurationUse this command when a new updated configuration file has beendownloaded to the CS4000 system. The system will re-start and then use thenew configuration file.

7 History

Use this menu to view previous events in the fire alarm system.

7.1 Fire History ListShows a list of the 500 latest fire alarms in chronological order.

7.2 Fault History List

Shows a list of the 500 latest fault alarms in chronological order.

7.3 Disconnection History ListShows a list of the 500 latest disconnections in chronological order.

7.4 Common History List

Shows a common list of the 500 latest pre alarms, fire alarms, fault alarms anddisconnections in chronological order.


18/40


Salwico CS4000

Definition of terms

External controls An output to activate external actions, for example release fire

doors or stop ventilation.

Alarm device Alarm device are outputs from the fire alarm activated in case

of fire, for example audible or optical alarms such as bells,

sirens and flashlights.

Disconnection A disconnection of a system component such as a zone or a

detector prevents fire- or fault alarms or control actions from

that unit.

Panel board, PB This is the control panel with alphanumerical display.

Alarm delay A delay before activating alarm device outputs when a fire is

detected. Normally set to 2 minutes (the delay is

programmable).

Alarm transfer output Supervised output indicating that there is at least one fire alarm

in system. Normally used to alert the fire brigade in onshoreinstallations.

Zone board, ZB Zone board for connection of max 16 conventional detector

loops This board can also be used as 16 input/outputs.

Loop board, LB3 Loop board for connection of 3 addressable detector loops.

Communication board, CB Optional board for connection of internal and external

communication devices. USB, TCP/IP and serial

communication possibilities.

Base board, BB Base board is the center of the central with basic in and

outputs. It controls the system communication etc.

Relay board, RB Optional board with 8 programmable relay contacts.

Power board, PB Power supply board.Warning A disturbance in the system not as dangerous as a fault

condition. This can for instance be a dirty detector or an open

door to a central.

Fault condition A signal that is given by the control panel in the event of a fault

in the system or on one of its components.

Loop A common name for the cable, detectors and manual call points

that are connected with the fire alarm central.

Zone A group of addressable loop units or an entire conventional

zone.

Loop unit Units located on the detector loop such as detectors, manualcall points or short circuit isolators.

MCP Manual call point. An external fire alarm button. Creates a fire

alarm when activated.

Pre-alarm A condition of where the detector senses a certain amount of

danger, but the level of the detected state is not enough to cause

a fire alarm.


19/40


Salwico CS4000

CS4000 System data

Supply voltage (other supply voltage is optional) 230 VAC

Internal system voltage 24 VDC

Number of detectors on one centralMax 512 (max according

to EN54 regulations)

Number of detectors in one addressable detector loop Max 254

No. of detectors on a conventional loop. Max 50

No. of addressable detector loops on loop board, LB3. 3

No. of conventional detector sections per zone board, ZB 16

No. of circuit boards/central (such as LB,ZB etc) Max 64

No. of control panels/repeaters in one central Max 4

No. of centrals connected together to a system Max 16

No. of zones in a system Max 65535

Cable length of a detection circuit. See further cable

requirements in CS4000 installation manual.

Max 2 000m unshielded

cable

Min. loop cable requirements 2 x 0,3 mm2unshielded

Communication parameters for the external system channelRS485, 19200 Baud,

Odd parity, 8 data bits

Communication parameters for the detector loops FSK keying


20/40


Salwico CS4000

CS4000 System : EN54 functions

Optional functions with requirements

The following optional functions with requirements are available in the CS4000 system:

Paragraph Function description

7.8 Output to alarm devices (Item C)

7.9 Output to fire alarm routing equipment (Item E)

7.10 Output to fire protection equipment (Item G)

7.11 Delays to outputs (Item C+E)

7.12 Co-incidence detection (Item C+E+G)

8.3 Fault signals from points

9.5 Disablement of addressable points

10 Test condition

The paragraphs above refer to EN54:2:1997/AC:1999.

Functions relating to other parts of the EN54 standard

The system includes an integrated power supply that fulfills all mandatory functions of

EN54:4.

Ancil lary functions not required by EN54

Earth failureCS4000 has capability to indicate earth failure individually per fire detection loop.

Control panel, CU

It is possible to mount the control unit separately from the central panel. See block

diagram in CS4000 Installation manual, chapter 1.


21/40

User Guide Chapter 2: Operations 19

Salwico CS4000

Chapter 2: Operations

Access levels

To prevent un-authorized operation of the system there are access

levels to protect the different functions of the CS4000. The user has to

login to the system or unlock the lock (mainly industrial applications)

before any vital operations can be performed. Without access to an

authorization code or a key the user can only view fire and fault alarms

and mute the local buzzer.

The system is in access level 1 when the door is closed or if it is

locked by the key.

The system automatically returns to access level 1 when the lock is

locked or after 30 minutes of inactivity.

There are five different access levels:

Access level Procedure to enter level Description of user

1 None, door is closed or lock is

locked.

General public, safety personnel.

2 Open door or unlock the lock. Personnel trained and authorized to operate

the system in case of fire or maintenance.

Disconnections not possible.

2B Open door and enter access code

for level 2B via menu/login.

Personnel trained and authorized to operate

the system in case of fire or maintenance.3 Open door and enter access code

for level 3 via menu/login.

Personnel trained and authorized to make

changes to the configured system.

4 Open door and enter access code

for level 4 via menu/login.

Only authorized service personnel trained by

Consilium.


22/40


Salwico CS4000

Descrip tion of the access levels

Access level 1

Only viewing of fire or fault alarms. Fire alarms have priority overfault alarms. Possibility to mute local buzzer.

Access level 2

As level 1 + access to the menu system. List status. Reset and muting

of alarms.

Access level 2B

As level 2 + make disconnections.

Access level 3

As level 2B + possibility to make changes to the configured system.

Access level 4

All functions available, including advanced service options.

Login

Press Menu from level 1 or go toMenu/ 4 login/ 1 loginand enter the

four-digit access code for the desired access level. The system will

acknowledge if the correct code is entered.Entering the system with the key gives direct access to level 2.

The default access codes are:

Level 2B 2222

Level 3 3333

Users

It is possible to pre-define users in the system. Each user is given a

unique name, personal access code and a pre-set access level.

Add new user

Users are added under:Menu/ 4 login/ 2 new user.

Delete user

Users are deleted under:Menu/ 4 login/ 3 delete user.


23/40


Salwico CS4000

Pre-alarm

The CS4000 is equipped with the function Pre-alarm that will give an

early alarm to a slow raise of the fire condition, for example a

smouldering fire. The Pre-alarm level is lower than the ordinary fire

alarm level.A pre-alarm will activate the local buzzer and the indication Pre-

alarm will be lit on the control unit. The pre-alarm will also be added

to the pre-alarm list found under:

Menu/ 2 Fire Alarms/ 2 Pre-Alarm List.It is only possible to mute a pre-alarm, not reset. It will remain in the

pre-alarm list until the fire condition is under or over (fire alarm) the

level for pre-alarm.

The pre-alarm will normally not activate any alarm devices or external

outputs.


24/40


Salwico CS4000

Fire alarm

When Fire is flashing

A fire alarm is detected within the system.

Information displayed

The following information is displayed on the control panel:

0System Fault

Home Disc.

Test

Alarm Device

Power

Alarm Transfer

Alarm Delay

Zone/Unit

2

Warning

OK

Pre-Alarm

Menu

Reset

FIREFAULT DISC.

NextMute

OK

ABC3

DEF' '1

5JKL

6MNOGHI

4

8TUV

9WXYZPQRS

7

F1

F2

F3

FIRE ALARM 1(2) 15.531 FIRE ZONE 2 MCP 23 .

Galley deck 4 .2 FIRE ZONE 1 SMOKE 206

Caf Panorama deck 14

_______________________________________________

RESET=Reset item, MUTE=Mute, OK=Details0=Disconnect, 1=Print item, 2=Print all.

Number of alarm(s)

Zone in alarm

Type of unit in alarm

Address number of unit in alarm (only for addressable loop)

Supplementary text 1 (if defined)

Press OKto view more details:

Time of alarm

Date of alarm

Supplementary text 2 about location of detector (if defined)

Mute

TheMUTEbutton has different function depending on the current

access level.

Access level 1

PressingMUTEcauses the internal buzzer to silence.

Access level 2 or higher


25/40


Salwico CS4000

PressingMUTEcauses the internal buzzer and all external alarms tosilence and mutes the fire alarm indication.

When the alarm is muted the fire indication stops flashing and turn

over to steady light.

Press OKfor more details.

Reset

PressRESETto reset the fire alarm.

Alarms cannot be reset if the fire condition remains.

Several alarms

If there is more than one fire alarm in the system, the red LED

indicators above theNEXTbutton are activated.

The first and last fire alarms are always displayed at the control panel.

Scroll through the different fire alarms with theNEXTbuttonorUP/DOWNarrows.

Reset and mute as above.

Type of fire alarms from conventional zones

The CS4000 will display whether a detector or a manual call point

generates the fire alarm. If two or more detectors are activated in the

same zone, the fire alarm will be presented as a manual call point.


26/40


Salwico CS4000

Fault indications

When Fault is flashing

0System Fault

Home Disc.

Test

Alarm Device

Power

Alarm Transfer

Alarm Delay

Zone/Unit

2

Warning

OK

Pre-Alarm

Menu

Reset

FIREFAULT DISC.

NextMute

OK

ABC3

DEF' '1

5JKL

6MNOGHI

4

8TUV

9WXYZPQRS

7

F1

F2

F3

FAULT ALARM 1(1) 18.53

_______________________________________________1 LOOP ANALOGUE 3 CABLE BREAK POSITIVE .

Loop 3 . On LB3 2 .

_______________________________________________

RESET=Reset current entry, MUTE=Mute allOK=Details, 1=Print item, 2=Print all.

A fault is detected within the system.

Information displayed

The following information is displayed in the control unit:

Number of fault(s) (i.e. how many faults are detected)

Type of fault

Identification of the faulty unit

Supplementary text for the faulty unit (if defined)

Press OKfor more details:

Time when fault occurred

Date when fault occurred

Supplementary text about location of fault (if defined)

Mute

PressMUTEto silence internal buzzer and mute all faults in list.

Press OKfor more details.


27/40


Salwico CS4000

Reset

All faults in the system are shown in the fault list.

Reset a fault:

1. Go to the fault list under:Menu/ 1 Fault Alarms/ 1 Fault List2. Choose the fault in the fault list and then pressRESETto reset

the fault alarm.

If the cause of the fault alarm remains the alarm cannot be reset.

Check the problem and deal with it. Then try to reset the fault again.

Reset all faults:

1. Go to:Menu/ 1 Fault Alarms/ 3 Reset All Faults

2. Press OK

Fault messages

If a fault occurres in the system it will be displayed at the control panelwith information about which part of the system that is faulty and also

a short description of the fault.

See Appendix A: Fault codes & Fuses for a list of all faults

messages.


28/40


Salwico CS4000

Disconnections

It is possible to disconnect different parts of the system, such as:

zones, detectors, manual call points, section units, alarm devices,

external control devices and loops. All disconnections are placed in a

disconnection list. The yellow indicationDISC. is lit on the controlunit when the first disconnection is defined in the system and remains

lit until all disconnections are reconnected.

To be able to make a disconnection you must enter access level 2B orhigher.

WARNING! When a fire detector or zone is disconnected the fire

alarm system will not be able to detect any occurring fire in that area.

It is therefore important that disconnections are minimized in terms of

quantity of disconnected units and duration of time.For example if dual detectors heat/smoke are installed it is possible to

disconnect only the smoke detection part of the detector and keep the

heat detecting part active or vice versa.

Disconnections available

There are four different disconnections available:

Permanent disconnection

The disconnection is permanent until it is manually reconnected.

Timer disconnection

Disconnection is instant and lasts for the time period entered (hh:mm).

Maximum disconnection time is 23h 59m.

Clock disconnection

Enter reconnection time. Disconnection is instant and the reconnection

will take place next time the entered time occurs. Maximum

disconnection time is 23h 59m.

Periodic disconnection A disconnection for a certain time period during certain days of the

week. Example: Disconnect zone 1 each Tuesday and Friday

between 7.00 17.00.

Acknowledgement of a new disconnection

After entering a new disconnection correctly, an acknowledgement is

presented on the control panel. The new disconnection is also added in

the disconnection list under:

Menu/ 3 Disconnections/ 2 Disconnection list


29/40


Salwico CS4000

Disconnecting zones

(access level 2B or higher)

Disconnections are made under:Menu/ 3 Disconnections/ 1 New

disconnection

To disconnect a conventional zone, follow the basic system below:

Step 1

Choose ZoneStep 2

Choose disconnection typeStep 3

Enter time

Zone number Permanent

Timer X

Clock X

Periodic X

To disconnect an addressable zone, follow the basic system below:

Step 1Choose Zone

Step 2Choose detector type

Step 3Choose disconnection type

Step 4Enter time

Zone number Smoke Permanent

All Timer X

Heat Clock X

Flame Periodic X

Manual Call Points

Example:

You want to disconnect zone 3 each Monday and Tuesday between

06.00-18.30.

1. Enter the disconnections menu either by pressing the shortcut

buttonDisc. or pressMenuand choose 3 Disconnectionsby

pressing 3and then press OK.

(Be sure to have access level 2B or higher)

2. Choose 1 New disconnection

3. Choose1 Disconnect Zone

4. Enter the zone number 3, then press OK

5. For addressable loop: Choose 2 All Detectors(manual call

points will remain active), then press OK

6. Choose 4 Periodic disconnection

7. Enter disconnection time 06001830, then press OK.

8. Disable all weekdays except Monday and Tuesday by pressing

the number for each weekday (i.e. 34567), then press OK


30/40


Salwico CS4000

Disconnecting addressable detectors

(access level 2B or higher)

Disconnecting individual detectors is only possible on addressableloops.

Disconnections of detectors are made under:

Menu/ 3 Disconnections/ 1 New disconnection/ 2 Detectors & Manual

Call Points

To disconnect an addressable detector, follow the basic system below:

Step 1

Choose

zone

Step 2

Choose

detector type

Step 3

Choose

detector address (orinterval)

Step 4

Choose

disconnection type

Step 5

Enter time

Zone

number

Smoke Address number(s) Permanent

All Timer X

Heat Clock X

Flame Periodic X

Manual Call

Point

Disconnecting alarm devices (bells etc)

(Access level 2B or higher)

Disconnections of external alarms is done under:

Menu/ 3 Disconnections/ 1 New disconn./ 4 External Alarm/ 1 Alarm

Device

Disconnection of alarm delay


Disconnection of alarm delay will activate the delay of alarm devices.

The delay time is programmable and normally set to two minutes.

Disconnection of alarm delay is done under:

Menu/ 3 Disconnections/ 1 New disconn./ 4 External Alarm/ 1 Alarm

Delay


31/40


Salwico CS4000

Disconnecting external outputs (for example fans, fire doors etc)


1. Select:Menu/ 3 Disconnections/ 1 New disconn./ 3 External

Control

2. Choose all outputs or select an individual output category to bedisconnected.

3. Press OK.

Disconnection of alarm transfer output


Disconnection of the alarm transfer (fire brigade) output is done

under:Menu/ 3 Disconnections/ 1 New disconn./ 3 External Control/ 2 Alarm

Transfer

Reconnection of disconnected items

All disconnections in the system are shown in the disconnection list.

Any reconnection is made from this list.

1. Go toMenu/ 3 Disconnections/ 2 Disconnection list.

2. Choose the disconnection you want to reconnect.

3. Press Reset button


32/40

User Guide Chapter 3: Installation 30

Salwico CS4000

Chapter 3: Installation

Electrical connection

Descr ipt ion of CS4000 PCBs

The CS4000 system is based on the following standard PCBs:

Panel Board, PB

This is the control panel with alphanumerical display.

Base Board, BB

Base board with the basic in and outputs, system communication etc.

Loop Board, LB3

Connection board for up to 3 addressable analogue detector loops

Zone board, ZB

Connection board for up to 16 conventional detector zones.

This board can also be used as 16 input/outputs.

Output Board, OB

Optional board with 8 programmable relay contacts.

Rectifier Board, RB

Power supply board.

Communication Board, CB

Optional board with USB, TCP/IP and serial communication

possibilities.


33/40


Salwico CS4000

Connection

Since all CS4000 systems are customer designed no standard exists for

how the different PCBs are to be connected in the system. However,

in the figure below you will find an example with one board of each

type showing the connection terminals.


34/40


Salwico CS4000

Testing

After installation of the fire alarm system the different parts of the

system shall be tested to assure correct function. The CS4000 has a

special test mode, which makes the testing easier. When a zone is intest mode it will not activate any external alarm devices or controls in

case of a fire. Each tested detector and manual call point will indicate

activation with a red LED. The units in alarm will also be

automatically reset when the heat or smoke concentration is under thealarm level or if the manual call point is reset. Fire alarms from zones

not in test mode will not be inhibited. Detectors and manual call points

in the zone will blink during test mode. The tested zone will

automatically return to normal operation after two hours.

Test a fire-detecting zone

Put the zone into test mode under: Menu/3 Disconnections/1 New

disconn./ 5 Test Mode

Enter the zone number and confirm with OKbutton

The indications DISC., Test and Zone/Unit will be lit to confirm the

test mode.

It is now safe to test each detector, manual call point etc in this fire

zone during two hours. Use suitable testing equipment.All alarms will be listed under: Menu/7 History/1 Fire History List

Reset test mode

After testing it is important to return the tested zone into normal

condition again. Make sure that there is no detectors or manual call

points still in alarm before leaving test mode.

The zones in test mode are listed in the disconnection list, found under:

Menu/3 Disconnections /2 Disconnection list.

Choose the zone in the disconnection list and then pressRESET.

Test the control unit display

It is possible to test the alphanumerical display, all indications on the

control panel and the local buzzer with the function Test display,

found under: Menu/5 Settings/4 Test display.


35/40

User Guide Appendix A Fault codes & Fuses 33

Salwico CS4000

Appendix A Fault codes & Fuses

Fault list

Listed below are all fault codes, their causes and how an operator with some

knowledge of the system can solve the problem.

Fault code Cause RemedyTwo loop units have the

same address

Check the units

Hardware fault Exchange the unit

A fuse is blown (a

secondary fault appears)

Exchange the fuse

128 NO ANSWER

Lost communication. The

system has recognized a unit

but lost contact with it due to

some interference. Cable break in a detector or

system loop (a secondaryfault appears)

Mend the cable

The detector has a faulty

sensor element.

Exchange unit129 SENSOR FAULT

The smoke detector is

exposed to wind

Take care of wind problem

Try to clean the detector with a vacuum

cleaner or by blowing high-pressure air on

it. If this does not help, exchange thedetector.

130 DIRTY SENSOR The detector has a dirtysensor element

Ion smoke detector: Exchange the detector

Fewer loop units found than

configured

Check the specification and re-define the

system

Loop units not correctlyinstalled

Connect the unit correctly

131 TOO FEW FOUND

Missing answer from a unit Check address (possible double address).

Otherwise exchange the unit.

132 TOO MANY FOUND More loop units found thanconfigured

Check the specification and re-define the

system

133 IN1 CABLE BREAK There is a cable break oninput 1

Mend the cable break

134 IN2 CABLE BREAK There is a cable break oninput 2

Mend the cable break

135 EXT 24V FAIL External 24V power sourcemissing.

The local power supply is defect.

136 FEEDBACK FAULT External load is missing. Check the cable and the external load.

137 POSITION FAULT A supervised unit (forexample a door or damper)

is in the wrong position.

Check for obstructions.

138 LOOP CABLE SHORT A short circuit in thedetector loop cable.

Locate the short circuit and fix it.

139 LOOP CABLE A SHORT Short circuit on the A-sideof a detector loop.


140 LOOP CABLE B SHORT Short circuit on the B-sideof a detector loop


141 CABLE BREAK POSITIVE A cable break on thepositive conductor has been

detected.

Locate the cable break and mend it.

142 CABLE BREAK NEGATIVE A cable break on thenegative conductor has been

Locate the cable break and mend it.


36/40


Salwico CS4000

detected.

Two units have the same

address.

Check the loop unit addresses

Loop unit faulty. Exchange the unit.

143 COMMUNICATION ERRORThe communication with a unit

is deficient.

Interference Locate interference and deal with it.

144 WRONG TYPE OF UNIT The type of unit specified is

different from the typefound or configured.

Check the specification and change

definition or the unit.

Unit faulty Exchange the unit145 UNKNOWN TYPE OF UNITThe type of unit specified is

unknown to the system.Wrong type of detector has

been installed

Install the correct type and restart the loop.

146 TIMER STUCK The timer has been activatedtoo long.

Check the unit.

148 DOUBLE ADDRESS Two units sharing the sameaddress

Change one of the addresses.

149 CABLE SHORT Short circuit on cable. Locate the short circuit and fix it.

150 VALVE CLOSED The valve is closed. Open the valve

151 CONFIGURED NOTPRESENT

Unit is configured but notpresent.

Add the unit or change the systemconfiguration.

152 PRESENT NOTCONFIGURED

Unit is present but not

configured.

Remove the unit or change the system

configuration.

153 HIGH CURRENT ON LOOP There is high current in theloop cable.

Check if there is to many units connected to

the loop. Compare with the loop

limitations.

154 LOOP POWER LOSS The loop voltage is missing. Exchange the loop board.

155 EARTH FAULT POSITIVE Too low impedance onpositive conductor.

Locate the earth fault and fix it.

156 EARTH FAULT NEGATIVE Too low impedance onnegative conductor. Locate the earth fault and fix it.

157 FUSE FAULT A fuse is defective. Replace the fuse.

158 BATTERY FUSE FAULT A battery fuse has blown ora cable break.

Replace fuse or mend the cable.

159 CABLE BREAK A cable break has beendetected.

Mend the cable.

160 CABLE OVERLOAD Too high current on anoutput.

Check external loads.

161 POWER FAULT The main power supply islost.

Check the main power supply.

162 EMERGENCY POWER

FAULT

Emergency power is lost. Check the emergency power supply.

163 BATTERY FAULT A bad battery is detected. Charge the battery. If the fault remains thenreplace the battery.

164 CHARGING LOSS The battery charger isunable to charge the battery.

Replace the battery charger.

165 EXTERNAL FAULT External equipment hasindicated fault.

Check the external equipment.

166 EARTH DETECTIONFAULT

Unable to detect earth fault. Replace the earth fault circuit.

167 CHECKSUM EEP Incorrect EPROMchecksum.

Contact our service department.

168 RESTARTED Something has restarted. If it happens repeatedly, contact our servicedepartment.

169 TOO LONG BOOT Exceeded the maximalallowed boot time.

If it happens repeatedly, contact our service

department.


37/40


Salwico CS4000

170 EXTERNAL LOAD ON LINE There is a too high externalload on a conventional zone.

Locate the load and deal with it.

171 EXTERNAL SOURCE ONLINE

Feeding voltage detected on

a conventional zone.

Locate the source and remove it.

172 LOW POWER SUPPLY IN1 Low voltage on the primary24VDC power supply to the

internal PCBS.

Check the power supply.

173 LOW POWER SUPPLY IN2 Low voltage on thesecondary 24VDC powersupply to the internal

PCBS.

Check the power supply.

174 LOW POWER SUPPLYLOCAL

Too low voltage on the

3.3V/5V feeding to the

internal circuit boards.

Contact our service department.

175 LOW POWER SUPPLY Too low incoming 24VDCsupply to the internal circuit

boards.

Check the power supply

The configuration file is

corrupt.

Check the configuration file and re-

configure the system.

176 SYSTEM CONF FAULT

An error has occurredduring downloading of the

configuration file.

Re-configure the system. If the faultremains, contact our service dept.

177 LOW PRESSURE External equipmentindicates low pressure.

Check the pressure on the supervised unit.

178 ACTUATOR 1 Missing feedback fromactuator 1

Check cables to actuator 1. If the cables are

OK, change the actuator.

179 ACTUATOR 2 Missing feedback fromactuator 2.

Check cables to actuator 2. If the cables are

OK, change the actuator.

209 WRONG TYPE OF UNITDEFINED

The type of unit specified is

different from the type

configured.

Change the unit or the system

configuration.

210 ERROR INCAUSE&EFFECTDEFINITIONS

Fault detected in the

configuration.

Check the configuration.

255 ILLEGAL Internal system error. Contact our service department.


38/40


Salwico CS4000

Fuses

If a fuse is defective in the system a fault will be displayed at the control units.

Locate and replace the fuse with the information below.

Fuse list

Location Fuse Fuse rating Fuse type

Base board F1: Alarm bell output 1AT 5x20 mm




Rectifier board F3: To transformer 3.15AF 5x20 mm

Rectifier board F4: To transformer 3.15AF 5x20 mm

Rectifier board F5: To external 230VAC 3.15AF 5x20 mm

Rectifier board F6: To external 230VAC 3.15AF 5x20 mm

Rectifier board F8: Battery 4 AF 5x20 mm

Rectifier board F9: Battery 4 AF 5x20 mm

Rectifier board F10: From transformer 6 AF 5x20 mm

Rectifier board F11: From transformer 6 AF 5x20 mm

Fuse locations on base board, BB.

Fuse locations on rectif ier board, RB.


39/40

User Guide Index 37

Salwico CS4000

Index

A

Access levels 17

Acknowledgement of a new disconnection

24

Add new user 18

Alarm delay 14

Alarm delay indicator 5

Alarm device 14

Alarm device indicator 5

Alarm transfer 14

Alarm transfer indicator 5

Alphanumerical display 6Arrow keys 7

B

Base board, BB 14

Base Board, BB 28

C

Cable length 15Choosing menu alternatives 8

Clock disconnection 24

Communication board, CB 14

Communication Board, CB 28

Connection 29

connection terminals 29

Control panel CS4000 4

conventional loop 15

Custom keys and indicators 6

D

Definition of terms 14

Delete user 18

Description of CS4000 PCBs 28

Description of keys and indicators 4

Description of the access levels 18

Disconnecting addressable detectors 26

Disconnecting alarm devices 26

Disconnecting external outputs 27

Disconnecting zones 25

Disconnection 14

Disconnection indicator 5

Disconnection of alarm delay 26

Disconnection of alarm transfer output 27

Disconnections 24

Disconnections shortcut button 6

E

Electrical connection 28

EN54 Optional functions 16

External controls 14

F

Fault condition 14Fault indications 22

Fault indicator 5

Fault list 31

Fault messages 23

Fields for custom text 6

Fire alarm 20

Fire alarm indicator 4

Fuses 34

G

General description 4

H

Home 9

Home shortcut button 6

I

Installation 28

K

key 17

Keyboard beep 12

L

login 17

Login 18Loop 14


40/40

User Guide Index 38

Salwico CS4000

Loop board, LB3 14

Loop Board, LB3 28

loop cable requirements 15

Loop unit 14

M

Max cable length 15

Max number of detectors 15

MCP 14

menu alternatives 10

Menu shortcut button 6

menu system 8

Menu tree CS4000 9

Mute 20

Mute button 6

N

Next button 6

Next indicator 6

No. of addressable detector loops 15

No. of conventional detector sections 15

Numerical keypad 6

O

OK buttons 6

P

Panel board 14

Panel Board, PB 28

Periodic 24

Permanent disconnection 24

Power board, PB 14

Power indicator 5Pre-alarm 14, 19

Pre-alarm indicator 6

R

Reconnection of disconnected items 27

Rectifier Board, RB 28

Relay board, RB 14

Relay Board, RB 28

Reset 21

Reset button 7

S

Several alarms 21

System data 15

System fault indicator 5

T

terminals 29

Test a fire-detecting zone 30Test indicator 5

test mode 30

Test the control unit displa 30

Testing 30

Timer disconnection 24

U

Users 18

V

voltage 15

W

Warning 14

Warning indicator 5

Z

Zone 14

Zone board, ZB 14, 28

Zone/Unit indicator 5

Documents

CONSILIUM 91240-001000 CS4000 user manual E1 04 2 E