Configuration Guide TP48200T V2

8/12/2019 Configuration Guide TP48200T V2

1/24

Configuration Guide of TP48200T

Issue 02

Date 2012-12-07

HUAWEI TECHNOLOGIES CO., LTD.


2/24

Issue 02 (2012-12-07)Huawei Proprietary and Confidential

Copyright Huawei Technologies Co., Ltd. i

Copyright Huawei Technologies Co., Ltd. 2012. All r ights reserved. No part of this document may be reproduced or transmitted in any form or by any means without priorwritten consent of Huawei Technologies Co., Ltd.

Trademarks and Permissions

and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.

All other trademarks and trade names mentioned in this document are the property of their respectiveholders.

Notice The purchased products, services and features are stipulated by the contract made between Huawei andthe customer. All or part of the products, services and features described in this document may not bewithin the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements,information, and recommendations in this document are provided "AS IS" without warranties, guarantees orrepresentations of any kind, either express or implied.

The information in this document is subject to change without notice. Every effort has been made in thepreparation of this document to ensure accuracy of the contents, but all statements, information, andrecommendations in this document do not constitute the warranty of any kind, express or implied.

Huawei Technologies Co., Ltd.

Address: Huawei Industrial BaseBantian, Longgang

Shenzhen 518129

People's Republic of China

Website: http://www.huawei.com

Email: [email protected]


3/24

Configuration Guide Contents

Issue 02 (2012-12-07) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

ii

Contents

1 By configuration file ( recommended ) ..................................................................................... 4 1.1 Tools ......................................................................................................................................................... 4

1.2 Setps ......................................................................................................................................................... 4

2 Configure the controller manually by website .................................................................. 12 2.1 Tools ........................................................................................................................................................12

2.2 steps .........................................................................................................................................................12

3 Configure the controller manually by LCD ............................................................................ 19 3.1 Tool ..........................................................................................................................................................19

3.2 Step ..........................................................................................................................................................19


4/24

Configuration Guide Tables


iii

Tables

Table 1-1 Items of configuration list ...............................................................................................................10


5/24

Configuration Guide 1 By configuration file (recommended)


4

We supply three methods to configure the controller of cabinets.

1 By configuration file ( recommended ) 1.1 Tools

A Computer which equipped a network card, net cable, and the configuration files namedD14A1currentcfg.tar.gz or D20A1currentcfg.tar.gz.

Notes:

D14A1currentcfg.tar.gz just for the cabinet type of TP48200T-D14A1 as followed Fig., youmust confirm the cabinet before you upload the configuration file.

D20A1currentcfg.tar.gz just for the cabinet type of TP48200T-D20A1 as followed Fig., youmust confirm the cabinet before you upload the configuration file.

Warning:

If you upload the power system with wrong configuration file, the configured data could nottake effect.

1.2 SetpsStep 1 configure your IP address of your computer

1. Choose Start > Control Panel .

2. Select Network Connections .

3. Please click Local Area by right button and then click Properties


6/24



5

the dialog box as follows

4. Please choose the Internet Protocol and click Properties button


7/24



6

5. Please choose Use the following IP address , and enter the right IP address, the Subnetmask and the Default gateway

6. Please click OK

Step 2 connect to the controller

1. Open Internet Explorer and input 192.168.1.168 .

You will see the following website.

2. Input the defaulted user name admin , and password 001 .

And you will see following website:


8/24



7

Step 3 Upload the configuration file.

Please make sure the configuration files in your computer, because we will use it soon. The1-level menu is in the following website.

1. Choose the Site Configuration in 1-level menu, and you will see the following website.

2. Please click the Configuration operation


9/24



8

You will see follow picture and then you can upload the configuration file.

3. Please click Browse .

4. A window will be shown, please choose the file named D14A1currentcfg.tar.gz or D20A1currentcfg.tar.gz and click open .


10/24



9

Warning:

You must upload the right configuration file according to the cabinet type, otherwise theconfiguration file could not take effect.

5. Then please click Send .6. The window will be showed, please click OK , and go on.

7. System will display that t he file uploaded successfully and please click OK to go on.

Controller will reset after file uploaded, and the website will be disconnected. When thecontroller starts work again, it will show the new configuration.

Step 4 Check the configuration in Alarm Configuration .

1. Connect controller as the Step 2.

2. Choose the Alarm Configuration in 1-level menu.

You will see some 2-level menus as the following website.

In every 2-level menu, the controller has many configuration items. You need check ifthe third parameter of every item is correct. The relation between the item and the third

parameter is as the table 1-1. If the configuration is not correct, please upload configurationfile again.


11/24



10

Table 1-1 Items of configuration list

2-level menu item configuration

Alarm RelayMajor Alarm/Critical Alarm Relay NA

Minor Alarm Relay NA

Site Summary

Supervision Unit Internal Fault NA

DC Over Vol tage MUE04A_DO4

DC Under Voltage MUE04A_DO4

DC Ultra Over Voltage MUE04A_DO4

DC Ultra Under Voltag e MUE04A_DO4

Phase A Over Voltag e MUE04A_DO2

Phase B Over Voltag e MUE04A_DO2

Phase C Over Vol tage MUE04A_DO2

Phase A Under Voltage MUE04A_DO2

Phase B Under Voltage MUE04A_DO2

Phase C Under Voltage MUE04A_DO2

Mains Failure MUE04A_DO2

Phase A Failu re MUE04A_DO2

Phase B Failure MUE04A_DO2

Phase C Failu re MUE04A_DO2

AC Over Vol tage MUE04A_DO2

AC Under Voltage MUE04A_DO2

Amb ient Hi gh Temp Alarm MUE04A_DO5

Amb ient Low Temp Alarm MUE04A_DO5

Amb ient Hi gh Humidi ty NA

Amb ient Low Humidity NA

Amb ient Ver y High Temp A larm MUE04A_DO5

Door Contact Alarm MUE04A_DO1

Water Detector Alarm NA

Smoke Detector Alarm NA

Wire Frame Alarm NA

ACB Alarm NA

Load Fuse Break MUE04A_DO4

Missin g Amb Temp Sensor 1 MUE04A_DO5

Amb Temp Senso r 1 Faul t MUE04A_DO5

Missing Amb Humi Sensor1 NA

Amb Humidi ty Sensor 1 Faul t NA

Unknown System Type NA

AC SPD Alarm MUE04A_DO2DC SPD Alarm MUE04A_DO4

Battery Manual Switch On NA

ATS Fault NA

Diesel Fault NA

PSU Overload NA

Rectifier Summary Rectifi er Lost MUE04A_DO3


12/24



11

Rectifi er Redundancy Acti ve MUE04A_DO3

PSU Not Redundant MUE04A_DO3

Single Rect Fault(Redundant ) MUE04A_DO3

Single Rect Fault(Not Redundant ) MUE04A_DO3

Multi Rect Fault MUE04A_DO3

PSU Load Fault MUE04A_DO3

High Rectif ier Capacity MUE04A_DO3

Low Rectif ier Capacity MUE04A_DO3

Rectifier

No Response MUE04A_DO3

AC Fail MUE04A_DO3

DC Over Vol tage MUE04A_DO3

Rectifi er Protec t MUE04A_DO3

Rectifi er Failure MUE04A_DO3

Fan Failure MUE04A_DO3

Battery Summary

Boost Charge Status MUE04A_DO4

Abno rm al Bat ter y Curr ent MUE04A_DO4

Temp Compensation Acti ve MUE04A_DO4Battery Discharge MUE04A_DO4

Battery High Temperature MUE04A_DO5

Battery Very High Temperatur e MUE04A_DO5

Battery Low Temperatur e MUE04A_DO5

Battery Very Low Temperature MUE04A_DO5

LLVD1 Disconnect ing MUE04A_DO4

BLVD Disconnecti ng MUE04A_DO4

LLVD1 Disconnected MUE04A_DO4

BLVD Disconnected MUE04A_DO4

Battery Test Cancelled MUE04A_DO4Missin g Batt Temp Sensor 1 MUE04A_DO5

Batt Temp Sensor 1 Fault MUE04A_DO5

Batt Current Imbalance MUE04A_DO4

Battery Fuse1 Break MUE04A_DO4






Battery1 Lost MUE04A_DO4

Battery2 Lost MUE04A_DO4Battery 3 Lost MUE04A_DO4




Battery 1 Imbalance MUE04A_DO4




13/24

Configuration Guide 2 Configure the controller manually by website


12




VRLA BatteryExceed Current Limit NA

Over Current MUE04A_DO4

ECC500

TCU+TEC Alarm NA

TEC Alarm NA

TCU Alarm NA

MUC01A_DI_1 Alarm NA






2 Configure the controller manually by website2.1 Tools

A Computer which equipped a network card and a net cable

2.2 stepsStep 1 configure your IP address of your computer

1. Choose Start > Control Panel .

2. Select Network Connections .

3. Please click Local Area by right button and then click Properties

the dialog box as follows


14/24



13

4. Please choose the Internet Protocol and click Properties button

5. Please choose Use the following IP address , and enter the right IP address, the Subnetmask and the Default gateway

6. Please click OK

Step 2 connect to the controller

1. Open Internet Explorer and input 192.168.1.168 .


15/24



14

You will see the follow website.

2. Input the defaulted user name admin , and password 001 .

And you will see following website:

Step 3

The 1-level menu is in the left of the website.


16/24



15

Choose the Alarm Configuration in 1-level menu.

And you will see some 2-level menu.


17/24



16

In every 2-level menu, the controller has many configuration items. For example, click thesite summary 2-level menu, we have 46 configuration items. We need configure themmanually.

I will give you an example.

If we want configure the door contact alarm, we need find it at 2-level menu.

1. Please click site summary at 2-level menu.

And we will see 39 items as the follow picture.

2. Find the Door Contact Alarm in the 46th item.


18/24



17

3. Click the panel in the left of the item and you will active the configuration process of theitem.

When words become black, you can configure it.


19/24



18

4. The item have five parameters, we just need configure the fourth parameter. Choose itand we will see some opinions.

5. Please choose the MUE04A_DO1

6. Click the Submit and your configuration will take effect.


20/24

Configuration Guide 3 Configure the controller manually by LCD


19

If the configuration is successful, the system displays a dialog box, indicating the commandhas been issued.

And you need configure 102 items in seven 2-level menus in the list. The item configurationlist is in the Table 1-1.

3 Configure the controller manually by LCD3.1 Tool

No tool is need.

3.2 StepThis picture is the front panel of the ECC500 controller, we need control the menu displayedin the LCD by the four key.

In the following picture I annotate the function of the key.

The followed picture is displayed after you power on the controller.


21/24



20

1. Use ENTER key and go on

2. Push ENTER key and you will see the 1-level menu.


22/24



21

3. Use the UP and DOWN key to choose the Settings menu and push the ENTER key.You will need to input the user name and password to enter this menu. The defaulteduser name is admin and the defaulted password is 001 .

Now you can see some 2-level menu. You can enter the 2-level menu.


23/24



22

Now we have 101 configurations item in seven 2-level menus, you need configure them one by one.

For example, if you want configure the Door Alarm , enter the Site Summary menu.

4. Choose the Door Alarm and use the ENTER key. We see followed picture.


24/24


I 02 (2012 12 07) H i P i t d C fid ti l 23

5. Push the ENTER to set E04A_DO1 and use the Cancel key to come back the 2-levelmenu.

You need set the configuration items one by one, so I do not recommend configure thecontroller by this way.

The configuration item list is in the Table 1-1.

----End

Documents

Configuration Guide TP48200T V2