CONFIGURATION DESCRIPTION RELATED …apps.geindustrial.com/publibrary/checkout/96A-4000?TNR=Electrical... · 1.0 control configuration groups ... user-configurable analog & digital

ELECTRICAL SCHEMATIC DRAWING - GE ZENITH ZBTECT SERIES TRANSFER SWITCHES - CLOSE TRANSITION TYPE - 4000A

LEGEND, FEATURES, OPERATION, AND ACCESSORIES

g ZENITH CONTROLS CHICAGO, IL 60609 USA

REVISION: A ECN : S-8713 THIS DRAWING CONTAINS PROPRIETARY AND CONFIDENTIAL INFORMATION. DUPLICATION, REPRODUCTION OR USE OF THIS DOCUMENT OR ITS CONTENTS IN ANY FORM

OTHER THAN AS EXPRESSLY PERMITTED BY ZENITH CONTROLS, INC. IS STRICTLY PROHIBITED.

DATE: 04/30/08 DRAFT: CE ENG: CE APPLICATION MX350

DESCRIPTION : ESTABLISHED JOB / MODEL : ZBTECT ZBTECT 4000 AMP

DRAWING NUMBER:

96A-4000 1 OF 12 REV:

A

5.0 SEQUENCE OF OPERATIONS ZTE SWITCHES ARE CONFIGURED TO ONE (1) OF THE FOLLOWING FIVE (5) OPTION PACKAGES. NOTE: ATS CATALOG NUMBER SCHEME, DIGIT #9, INDICATES THE INSTALLED CONTROL PACKAGE

1.0 CONTROL CONFIGURATION GROUPS

CONFIGURATION DESCRIPTION

A STANDARD PACKAGE FOR AUTOMATIC ATS. INCLUDES FULL FUNCTION ATS CONTROL, DIAGNOSTICS, USER CONTROL SWITCHES, (4) USER-CONFIGURABLE INPUTS, AND (4) USER-CONFIGURABLE OUTPUTS

B ALL FEATURES IN "A" PLUS: USER-CONFIGURABLE ANALOG & DIGITAL ALARMS, 20-CHANNEL DATA LOGGER, 10-CHANNEL WAVEFORM CAPTURE, AUTO LOAD SHED FEATURE

C ALL FEATURES IN "B" PLUS: (4) ADDITIONAL USER-CONFIGURABLE INPUTS AND OUTPUTS (TOTAL 8 INPUTS, 8 OUTPUTS)

D ALL FEATURES IN "C" PLUS: (4) ADDITIONAL USER-CONFIGURABLE INPUTS AND OUTPUTS (TOTAL 12 INPUTS, 12 OUTPUTS), FLEXLOGIC USER-PROGRAMMABLE CUSTOM LOGIC EDITOR

M STANDARD PACKAGE FOR MANUAL ATS. INCLUDES FULL FUNCTION ATS CONTROL, DIAGNOSTICS, USER

CONTROL SWITCHES (SEE ITEM #4), (4) USER-CONFIGURABLE INPUTS, AND (4) USER-CONFIGURABLE OUTPUTS

SIGNAL (CODE) DESCRIPTION RATINGS

ENGINE START SIGNAL (E) START SIGNAL FROM ATS TO GENSET IN EVENT OF LOSS OF PREFERRED SOURCE

FORM 'C' CONTACTS, 10A @ 28VDC/120VAC

REMOTE TEST SIGNAL (Q2)

MAINTAINED CONTACT (CLOSE FOR TEST) FROM BUILDING CONTROL SYSTEM TO SIMULATE AN OUTAGE CONDITION. SWITCH WILL START

GENERATOR AND TRANSFER LOAD. SWITCH WILL RETURN TO PREFERRED SOURCE UPON REMOVAL OF TEST SIGNAL.

FORM 'C' CONTACT, RATED FOR 28VDC,

1A MINIMUM

SOURCE 1 CONNECTED TO LOAD (A4) AUXILIARY CONTACT INDICATING LOAD IS CONNECTED TO ATS SOURCE #1

QTY (2) N/O CONTACTS, 10A @

28VDC/120 VAC

SOURCE 2 CONNECTED TO LOAD (A3) AUXILIARY CONTACT INDICATING LOAD IS CONNECTED TO ATS SOURCE #2

QTY (2) N/O CONTACTS, 10A @

28VDC/120 VAC

BYPASS MTS CONNECTED TO SOURCE 1

AUXILIARY CONTACT INDICATING THAT OPERATOR HAS MANUALLY BYPASSED SOURCE 1 TO THE LOAD. (BYPASS ATS ONLY)

QTY (1) N/O CONTACT, 10A @ 28VDC/120 VAC

BYPASS MTS CONNECTED TO SOURCE 2

AUXILIARY CONTACT INDICATING THAT OPERATOR HAS MANUALLY BYPASSED SOURCE 2 TO THE LOAD (BYPASS ATS ONLY)

QTY (1) N/O CONTACT, 10A @ 28VDC/120 VAC

2.0 STANDARD CONTROL INTERFACE SIGNALS ZTE SWITCHES SUPPORT THE FOLLOWING STANDARD INTERFACE SIGNALS. SEE CUSTOMER CONNECTION DIAGRAM FOR TERMINAL LOCATIONS AND DETAILS

3.0 NETWORKING AND METERING OPTIONS ZTE SWITCHES MAY BE CONFIGURED WITH BUILT-IN NETWORKING AND METRING OPTIONS. SEE TRANSFER SWTICH CATALOG NUMBER DIGITS #13 AND #14 AND THE TABLE BELOW TO DETERMINE INSTALLED OPTIONS

DIGIT #13 DESCRIPTION

D, G, H, J, L, M, N, OR O INCLUDES POWER QUALITY METERING. INCLUDES (2) CT'S FOR SINGLE PHASE, (3) CT'S FOR 3PH/3W OR (4) CT'S FOR 3PH/4W SYSTEMS.

DIGIT #14 DESCRIPTION X NO COMMUNICATIONS S INCLUDES BUILT-IN SERIAL (RS-485) MODBUS RTU COMMUNICATIONS

E INCLUDES BUILT-IN SERIAL (RS-485) MODBUS RTU COMMUNICATIONS AND ETHERNET/TCPIP

COMMUNICATIONS. NOTE: COMMUNICATION PORTS MAY BE USED SIMULTANEOUSLY.

4.0 NON-STANDARD CONTROL OPTIONS THE FOLLOWING OPTIONS MAY BE INSTALLED ON THE ATS. SEE TRANSFER SWITCH CATALOG NUMBER DIGITS #9, #13, AND #14 AND THE TABLE BELOW TO DETERMINE INSTALLED OPTIONS

ORDER CODE DIGIT

#

VALUE FEATURE FEATURE DESCRIPTION

13 A, E, F,

G, H, I, J, OR 0

REMOTE LOAD SHED

PROVISIONS ON POWER PANEL TO PERMIT TRANSFER OF SWITCH FROM LIVE NON-PREFERRED SOURCE TO EITHER DEAD CENTER POSITION (DELAY-TYPE AND CLOSED TYPE

ATS ONLY) OR DE-ENERGIZED PREFERRED SOURCE. ACTIVATES ON REMOTE CONTACT SIGNAL FROM BUILDING AUTOMATION OR PARALLELING SWITCHGEAR SYSTEM. SWITCH DISCONNECTS THE LOAD IMMEDIATELY UPON RECEIPT OF THE LOAD SHED SIGNAL, AND

RETURNS TO LIVE SOURCE AFTER REMOVAL OF LOAD SHED SIGNAL.

9 B, C, OR D

AUTO LOAD SHED

CONTROL INCLUDES PROVISIONS FOR AUTOMATIC DISCONNECTION FROM NON-PREFERRED SOURCE IN EVENT OF UNDERFREQUENCY, UNDERVOLTAGE, OR OVERPOWER/KW. EACH SETPOINT IS INDEPENDENTLY SETABLE, WITH INDIVIDUAL TIME DELAYS. IF SWITCH IS

CONFIGURED WITH LOAD SHED (DIGIT #13 ABOVE) SWITCH CAN BE CONFIGURED TO MOVE TO CENTER OFF OR DE-ENERGIZED NON-PREFERRED SOURCE. IF SWITCH DOES NOT

INCLUDE LOAD SHED, A USER-CONFIGURABLE OUTPUT MAY BE ASSIGNED TO AUTO LOAD SHED FEATURE TO PERMIT SHUNT TRIP OF DOWNSTREAM LOAD(S). ONCE ACTIVATED, AUTO LOAD SHED REQUIRES MANUAL/USER RESET VIA MENU RESET PUSHBUTTON OR

CONFIGURABLE AUTO LOAD SHED RESET INPUT.

13 B, E, H, I,

J, K, L, OR M

CTAP CHICAGO ALARM/CTAP FUNCTION. INCLUDES AUDIBLE ALARM UPON CONNECTION TO NON-PREFERRED SOURCE.

13 C, F, I, J, K, M, N,

OR O P2 EXTENDED ENGINE START RELAY - ADJ 0.5 SEC TO 300 SEC

13 D, G, H,

J, L, M, N OR O

MPQ INCLUDES (2) CT'S FOR SINGLE PHASE, (3) CT'S FOR 3PH/3W OR (4) CT'S FOR 3PH/4W SYSTEMS. ADDS POWER QUALITY METERING.

NOTE: SEE O&M MANUAL FOR ADDITIONAL SEQUENCE OF OPERATION DETAILS AND DIAGNOSTICS.

INDICATOR DESCRIPTION SOURCE AVAIL LED'S S1 (GREEN) AND S2 (RED) INDICATE SOURCE HEALTHY SOURCE CONN LED'S S1 (GREEN) AND S2 (RED) INDICATE SOURCES CONNECTED TO LOAD

ALARM LED RED LED, INDICATIES AN ACTIVE ALARM. SEE STATUS SCREEN (HOME-->STATUS) FOR DETAILED ALARM MESSAGE

TD ACTIVE RED LED, INDICATES CONTROLLER IS TIMING FOR NEXT ACTION. SEE

STATUS SCREEN (HOME-->STATUS) FOR DESCRIPTION OF THE TIME DELAY AND DISPLAY OF REMAINING TIME

XFER INHIBIT

INDICATES ATS IS READY TO TRANSFER TO A SOURCE, BUT IS RECEIVING AN INHIBIT TRANSFER SIGNAL. INHIBIT COMMAND MAY BE LOCAL

DISCONNECT SWITCH (DS), LOCAL OR REMOTE AUTO/MANUAL SWITCH, OR INHIBIT TRANSFER SIGNALS

ALARM RESET USED TO RESET LATCHED ALARM CONDITIONS. TEST JUMP BUTTON TO TEST MENU. INFO JUMP BUTTON TO RUN REPORT.

CONTROL JUMP BUTTON TO CONTROL MENU. HOME JUMP BUTTON TO HOME SCREEN

UP/DOWN ARROW PERMITS UP/DOWN SCROLLING WITHIN SCREEN ESC' KEY BRINGS OPERATOR TO PREVIOUS SCREEN

ENTER' KEY SELECTS ITEMS WITHIN MENU SYSTEM AND CONFIRMS OPERATIONS HELP' KEY TRIGGERS MENU-DEPENDENT HELP POPUP MESSAGE

USB PORT PERMITS CALIBRATION UPLOAD/MODIFY/DOWNLOAD USING ENERVISTA SETUP ™ SOFTWARE.

5 x SOFT KEYS (BLUE ARROWS)

MENU-DEPENDENT PUSHBUTTONS. FUNCTION OF PUSHBUTTON IS INDICATED ON GRAPHICAL SCREEN ABOVE BUTTON.

ELEMENT LOCATION IN MENU LAST & NEXT EXERCISE TIME HOME SCREEN

LAST TRANSFER TIMES s1-->s2, AND s2-->S1 HOME SCREEN SWITCH AMP, VOLT RATING AND TYPE HOME SCREEN

PREFERRED SOURCE SETTING HOME SCREEN SOURCE VOLTAGES, FREQUENCY HOME-->VALUES

LOAD AMPS, KW, KVAR, PF (REQUIRES METERING OPTION) HOME-->VALUES

ALARM STATUS, STATUS OF TIMERS HOME-->STATUS CURRENT CONFIGURATION / ASSIGNENT OF

CUSTOMER INPUTS HOME-->STATUS-->INPUTS

CURRENT CONFIGURATION / ASSIGNENT OF CUSTOMER OUTPUTS HOME-->STATUS-->OUTPUTS

CURRENT CONFIGURATION OF LOAD CONTROL RELAYS (ELEVATOR, LOAD PRE-

SIGNAL) HOME-->SETPOINT-->CONFIG

S1 FAIL/RESTORE SETTINGS HOME-->SETPOINT-->OPERATION-->S1 SETTING S2 FAIL/RESTORE SETTINGS HOME-->SETPOINT-->OPERATION-->S2 SETTING TIME DELAY ADJUSTMENTS HOME-->SETPOINT-->OPERATION-->TIMERS

EVENT LOG HOME-->DIAG STATISTICS HOME-->DIAG-->STATS

CONTROL SWITCHES HOME-->SETPOINT-->CONTROL OR GREEN 'CONTROL' PUSHBUTTON

EXERCISER STATUS HOME-->EXERCISER SET EXERCISER TYPE HOME-->EXERCISER-->SETUP-->ENTER

TEST HOME-->EXERCISER-->TEST OR GREEN 'TEST' PUSHBUTTON

6.0 STANDARD INDICATORS, PUSHBUTTONS, AND ANNUNCIATION

ZTE OPERATOR DISPLAY (DOOR MOUNTED)

STATE DESCRIPTION FUNCTION: RELATED

USER SETTINGS

LOCATION OF SETTINGS IN

MENU

0 CONNECTED TO

PREFERRED SOURCE

STAY ON PREFERRED SOURCE UNTIL FAILURE IS DETECTED OR A TEST WITH LOAD IS INITIATED. (NOTE: JUMP TO STEP #3 IF TEST WITH LOAD)

SETTING OF PREFERRED

SOURCE

SETPOINT-->OPERATION--

>S1 (S2) SETTINGS

1 PREFERRED SOURCE FAILURE CONTROL SENSES THE FAILURE OF THE DESIGNATED PREFERRED SOURCE

SOURCE FAILURE

SETTINGS


>S1 (S2) SETTINGS

2 PREFERRED

SOURCE FAIL TIMER

CONTROL INITIATES A TIME DELAY ON STARTING OF GENERATOR IN CASE OF FAST RETURN OF SOURCE

DELAY FOR GENERATOR

START


>TIMERS

3 START GENERATOR

CONTROL SENDS A START COMMAND TO THE GENERATOR ON

EXPIRATION OF THE TIME DELAY (P) IN #2 ABOVE

4 NON-PREFERRED

SOURCE AVAILABLE

CONTROL DETECTS THAT THE NON-PREFERRED SOURCE IS AVAILABLE SOURCE RETURN

SETTINGS


>S1 (S2) SETTINGS

5 NON-PREFERRED

SOURCE STABILITY TIMER

CONTROL INITIATES A TIME DELAY (W) TO PERMIT THE GENERATOR TO

STABILIZE BEFORE TRANSFER OF THE LOAD.

DELAY – XFER TO

NON PREFERRED

SRC


>TIMERS

6

COMMIT TRANSFER TO

NON-PREFERRED SOURCE (S13)

IF (S13) IS SET TO "ENABLED" - CONTROL WILL INITIATE THE TRANSFER SEQUENCE EVEN IF THE PREFERRED SOURCE RETURNS BEFORE

EXPIRATION OF TIME DELAY (W) IN #5 ABOVE.

IF (S13) IS SET TO "DISABLED" AND PREFERRED SOURCE RETURNS BEFORE EXPIRATION OF TIME DELAY (W) IN #5 ABOVE, CONTROL REMOVES START

SIGNAL AND STAYS CONNECTED TO PREFERRED SOURCE.

COMMIT XFER

SWITCH (S13)

HOME-->SETPOINT-->CONTROL or GREEN

'CONTROL' PUSHBUTTO

7 AUTO/ MANUAL SELECT SWITCH PERMISSIVE (S5)

IF AUTO/MANUAL SWITCH SET TO "AUTO" OR "MANUAL S2 TO S1 ONLY (S5)" – ATS WILL AUTOMATICALL INITIATE THE TRANSFER SEQUENCE

UPON EXPIRATION OF TIME DELAY (W) IN #5 ABOVE.

IF AUTO/MANUAL SWITCH SET TO "MANUAL S1 TO S2, S2 TO S1 (S12)" – ATS WILL WAIT FOR A PERMISSIVE SIGNAL BEFORE INITIATING THE

TRANSFER SEQUENCE. PERMISSIVE SIGNAL IS EITHER AN OPERATOR PUSHBUTTON ON THE 'STATUS' SCREEN OR CUSTOMER INPUT SIGNAL.

AUTO /MAN SELECT SWITCH


'CONTROL' PUSHBUTTON

8 CONNECT TO

NON-PREFERRED SOURCE

IF TEST WITH LOAD: CONTROL WILL CONNECT THE LOAD TO THE NON-PREFERRED BEFORE DISCONNECTING THE PREFERRED SOURCE. IF

OUTAGE: THE PREFERRED SOURCE IS OPENED BEFORE CLOSURE OF THE NON-PREFERRED SOURCE. BOTH OPERATIONS ARE INITIATED AFTER

EXPIRATION OF TIME DELAY (W) IN #5 ABOVE OR RECIEPT OF PERMISSIVE SIGNAL (#8 ABOVE)

9 GEN

STABILIZATION TIMER

CONTROL WILL DELAY ACTIVATION OF SOURCE 2 FAILURE (UNDER VOLTS/FREQ) TO PERMIT GENERATOR SET TO STABILIZE AFTER

CONNECTION OF LOAD.

TIME DELAY FOR GEN

SAG SETPOINT--

>OPERATION-->TIMERS

10 PREFERRED

SOURCE AVAILABLE

CONTROL WILL SENSE THE RETURN OF THE DESIGNATED PREFERRED SOURCE, OR DETECT THAT THE TEST WITH LOAD OPERATION HAS BEEN

CANCELLED.

SOURCE RETURN

SETTINGS


>S1 (S2) SETTINGS

11 PREFERRED

SOURCE RETURN TIMER

CONTROL INITIATES A TIME DELAY (T) TO PERMIT UTILITY POWER TO STABILIZE

DELAY – XFER TO

PREFERRED SRC


>TIMERS

12 AUTO/MANUAL SELECT SWITCH PERMISSIVE (S5)

IF AUTO/MANUAL SELECT SWITCH IS SET TO "AUTO" – ATS WILL AUTOMATICALL INITIATE THE RE-TRANSFER SEQUENCE UPON

EXPIRATION OF TIME DELAY (T) IN #11.

IF AUTO/MANUAL SWITCH IS SET TO "MANUAL S1 TO S2, S2 TO S2 (S12)" – ATS WILL WAIT FOR PERMISSIVE SIGNAL BEFORE INITIATING THE

RETRANSFER SEQUENCE. PERMISSIVE SIGNAL IS EITHER AN OPERATOR PUSHBUTTON ON THE 'STATUS' SCREEN OR CUSTOMER INPUT SIGNAL.

AUTO /MAN SELECT SWITCH


'CONTROL' PUSHBUTTON

13 WAIT FOR

SOURCED IN SYNC

CONTROL WILL WAIT FOR EXPIRATION OF THE T-TIMER (#11 ABOVE) AND THEN WAIT FOR THE PHASE ANGLE, VOLTAGE LEVEL, AND FREQUENCY

OF THE SOURCES TO MATCH BEFORE INITIATING A MAKE-BEFORE-BREAK RETRANSFER TO THE PREFERRED SOURCE

FACTORY SETTINGS

FOR VOLTS, HZ, AND ANGLE MATCH

14 RE-CONNECT TO

PREFERRED SOURCE

WHEN IN-SYNC CONDITIONS ARE REACHED, CONTROL WILL CONNECT THE PREFERRED SOURCE TO THE LOAD, THEN IMMEDIATELY

DISCONNECT THE NON-PREFERRED SOURCE.

15 GENERATOR COOLDOWN

CONTROL WILL CONTINUE TO SEND START SIGNAL TO GENERATOR TO PERMIT UNLOADED RUNNING AND COOLDOWN OF GENSET

TIME DELAY FOR ENGINE COOLDOWN

TIMER SETPOINT--

>OPERATION-->TIMERS

16 GENERATOR STOP

CONTROL WILL REMOVE THE GENERATOR START SIGNAL AFTER EXPIRATION OF COOLDOWN TIME DELAY IN #15 ABOVE

ELECTRICAL SCHEMATIC DRAWINGS - GE ZENITH ZBTECT SERIES TRANSFER SWITCHES - CLOSE TRANSITION TYPE - 4000A

LEGEND, FEATURES, OPERATION, ACCESSORIES


REVISION: A ECN: S-8713 THIS DRAWING CONTAINS PROPRIETARY AND CONFIDENTIAL INFORMATION. DUPLICATION, REPRODUCTION OR USE OF THIS DOCUMENT OR ITS CONTENTS IN ANY FORM



DESCRIPTION: ESTABLISHED JOB/MODEL: ZBTECT ZBTECT 4000 AMP

DRAWING NUMBER:

96A-4000 2 OF 12 REV:

A

` PARAMETER RANGE OF SETTINGS DEFAULT

SETTING LOCATION ON DISPLAY

(FOLLOW LISTED NAVIGATION)

UNDERVOLTAGE 75% TO 99% NOMINAL 80% HOME>SETPOINT>OPERATION>S1 SETTINGS (OR S2 SETTINGS)

UNDERFREQUENCY 45.0 TO 59.9 HZ UTIL: 59 HZ GEN: 54 HZ SAME AS ABOVE

OVERVOLTAGE 105% TO 110% NOMINAL 110% SAME AS ABOVE OVERFREQUENCY 50.1 TO 63.0 HZ OFF SAME AS ABOVE

VOLTAGE IMBALANCE 5% TO 20% PHASE-PHASE 10% HOME>SETPOINT>CONTROL> ALARMS

VOLTAGE IMBALANCE TIME DELAY 1 TO 60 SECONDS 30 SEC HOME>SETPOINT>CONTROL>

ALARMS

PARAMETER RANGE OF SETTINGS DEFAULT

SETTING LOCATION ON DISPLAY


UNDERVOLTAGE 85% TO 100% NOMINAL 90% HOME>SETPOINT>OPERATION>S1 SETTINGS (OR S2 SETTINGS)

UNDERFREQUENCY 45.1 TO 60.0 HZ UTIL: 59.5 HZ GEN: 57 HZ

SAME AS ABOVE

OVERVOLTAGE 103% TO 108% NOMINAL 105% SAME AS ABOVE OVERFREQUENCY 50.0 TO 62.9 HZ OFF SAME AS ABOVE

VOLTAGE IMBALANCE * 5% TO 20% PHASE-PHASE 10% HOME>SETPOINT>CONTROL> ALARMS

VOLTAGE IMBALANCE TIME DELAY * 1 TO 60 SECONDS 30 SEC HOME>SETPOINT>CONTROL>

ALARMS * AVAILABLE 3-PHASE UNITS ONLY

•

DESCRIPION ON DISPLAY EXTENDED DESCRIPION SETTING RANGE DEFAULT

SETTING

LOCATION ON DISPLAY


DELAY FOR GENERATOR

START

DELAY FROM FAILURE OF PREFERRED SOURCE TO

SENDING OF START SIGNAL TO GENERATOR

0 TO 10 SEC (0 TO 259 MIN IF 120 VAC EXTERNAL

POWER SUPPLY CONNECTED) 3 SEC. HOME>SETPOINT>

OPERATION>TIMERS

DELAY - XFER TO

NON-PREFERRED

SRC

DELAY ON TRANSFER TO NON-PREFERRED SOURCE AFTER SENSING THAT SOURCE IS

HEALTHY

0 SEC TO 5 MINUTES 259 MIN. (15,540 SEC).

NOTE: BYPASS OF TIME DELAY PERMITTED VIA PUSHBUTTON ON

STATUS SCREEN

3 SEC. SAME AS ABOVE

TIME DELAY FOR GEN

SAG

DELAY ON SENSING OF ALTERNATE SOURCE FAILURE

TO PERMIT GENSET TO RECOVER FROM LOAD IMPACT

0 SEC TO 30 SEC. NOTE: BYPASS OF TIME DELAY

PERMITTED VIA PUSHBUTTON ON STATUS SCREEN

OFF/ 0 SEC. SAME AS ABOVE

DELAY - XFER TO

PREFERRED SRC

DELAY ON RE-TRANSFER TO PREFERRED SOURCE TO

ENSURE SOURCE IS HEALTHY AND 2ND FAILURE IS UNLIKELY

0 SEC TO 259 MINUTES. NOTE: BYPASS OF TIME DELAY


30 MINUTES SAME AS ABOVE

DELAY FOR ENGINE

COOLDOWN

DELAY TO PERMIT UNLOADED RUNNING OF GENSET FOR

COOLDOWN

0 MIN:0 SEC TO 60MIN:0SEC. NOTE: BYPASS OF TIME DELAY


5 MINUTES SAME AS ABOVE

7.0 NORMAL/PREFERRED & EMERGENCY/ALTERNATE SOURCE FAILURE SETTINGS

8.0 NORMAL/PREFERRED & EMERGENCY/ALTERNATE SOURCE RETURN SETTINGS

9.0 TIME DELAY SETTINGS

9.5 FAIL TO SYNC AND EXTENDED PARALLEL PROTECTION

FAIL TO SYNC ALARM - WHEN TRANSFERRING BETWEEN ENERGIZED SOURCES IN CLOSED TRANSITION MODE, CONTROL WILL INITIATE AN ALARM IF SOURCES FAIL TO REACH SYNCHONISM WITHIN 60 SECONDS. ALARM (RED) LED WILL LIGHT, AND AUDIBLE HORN WILL BE ACTIVATED. ALARM SILENCE PUSHBUTTON IS AVAILABLE ON DISPLAY. A BYPASS PUSHBUTTON IS ALSO PROVIDED TO EXTENDED PARALLEL PROTECTION - IN A CLOSED TRANSTION TRANSFER, THE TIME PERIOD THAT BOTH SOURCES ARE CLOSED TO THE LOAD IS CONTROLLED TO BE LESS THAN, OR EQUAL TO 100ms. A TWO-STAGE PROTECTION SYSTEM IS PROVIDED TO PROTECT AGAINST EXTENDED PARALELING OF BOTH SOURCES DURING A CLOSED TRANSITON TRANSFER.

OPEN LAST CLOSED PROECTION: IF THE CONTROL FAILS TO OPEN THE SOURCE THAT IT IS ATTEMPTING TO TRANSFER OUT OF WITHIN 500ms. , AN ALARM WILL SOUND AND THE SOURCE THAT WAS LAST CLOSED WILL BE OPENED. TRANSFER OPERATION WILL BE LOCKED OUT UNTIL THE PROBLEM HAS BEEN RECTIFIED AND THE RESET PUSHBUTTON HAS BEEN PRESSED.

BACKUP SHUNT TRIP PROTECTION: A SIGNAL WILL BE PROVIDED TO SHUNT TRIP THE UPSTREAM GENERATOR CIRCUIT BREAKER IF BOTH SOURCES REMAIN CLOSED FOR 750ms. THE SIGNAL WILL REMAIN ACTIVE UNTIL ONE OF THE SOURCES IS OPEN. THE BACKUP SHUT TRIP SYSTEM UTILIZES LIMIT SWITCHES AND A BACKUP CONTROL SYSTEM THAT IS COMPLETELY INDEPENDENT OF, AND REDUNDENT TO THE MX350 CONTROL SYSTEM.

10.0 PROGRAMMABLE ENGINE EXERCISER

A PROGRAMMABLE ENGINE EXERCISER IS PROVIDED AS A STANDARD CONTROL FEATURE ON ALL ZTE TRANSFER SWITCHES. TWO (2) DIFFERENT TYPES OF EXERCISERS ARE CONFIGURABLE IN THE CONTROLLER:

- PERIODIC EXERCISER: IF ENABLED, THE ATS WILL PERFORM A TEST FUNCTION ON A PERIODIC BASIS, DEPENDING ON THE EXERCISER SETTING TYPE.

o PROGRAMMBLE TYPES: THE TYPE IS USER PROGRAMMABLE AS ‘DAILY’, ‘WEEKLY’, ’14 DAYS’, OR ’28 DAYS’ o # PROGRAMABLE EVENTS: UP TO (7) SEPARATE TEST EVENTS MAY BE PROGRAMMED, EACH WITH START TIME,

START DATE, AND RUN DURATION. o OPERATION DESCRPTION: EACH TEST EVENT WILL AUTOMATICALLY RE-INITIATE EVERY DAY, WEEK, 14 DAYS,

OR 28 DAYS – IN ACCORDANCE WITH THE EXERCISER SETTING. o RANGES: ENGINE RUN DURATION RANGE IS 0 MIN: 1 SEC TO 59 MIN: 59 SEC

- CLOCK EXERCISER: IF ENABLED, THE ATS WILL PERFORM A TEST FUNCTION AT SPECIFIC DATES/TIMES SETUP IN THE

CONTROLLER BY THE USER/OPERATOR. o PROGRAMMBLE TYPES: THE TYPE IS USER PROGRAMMABLE AS ‘365 DAYS’ o # PROGRAMABLE EVENTS: UP TO (24) SEPARATE TEST EVENTS MAY BE PROGRAMMED, EACH WITH START TIME,

START DATE, AND RUN DURATION. o OPERATION DESCRPTION: EACH TEST EVENT WILL BE INIT ATE/TIME SET FOR EACH EVENT. IATED AT THE Do RANGES: RUN DURATION RANGE IS 0 MIN: 1 SEC TO 59 MIN: 59 SEC

11.0 STANDARD CONTROL SWITCHES

SWITCH FUNCTION

(CODE) DESCRIPTION

LOCATION OF APPLICABLE CONTROL

SETTINGS IN ZTE DISPLAY

ADJUST RANGE

FACTORY DEFAULT

REMOTE ACTIVATION PERMITTED (CUSTOMER

CONFIG INPUT)

PREFERRED SOURCE SELECT SWITCH (S3)

PERMITS USER SELECTION OF THE PREFERRED SOURCE

HOME-->SETPOINT-->CONTROL or GREEN 'CONTROL' PUSHBUTTON

S1 OR S2 S1 YES

COMMIT TRANSFER TO S2 (S13)

IF SET TO ENABLED/YES: CONTROL WILL CONNECT TO THE NON-PREFERRED SOURCE EVEN IF PREFERRED RETURNS BEFORE EXPIRATION OF PREFERRED SOURCE FAILURE TIME DELAY IF SET TO DISABELED/NO: CONTROL WILL REMOVE START SIGNAL AND STAY CONNECTED TO THE PREFERRED SOURCE IF PREFERRED RETURNS BEFORE EXPIRATION OF PREFERRED SOURCE FAILURE TIME DELAY


ENABLED (YES), DISABLED (NO)

DISABELED (NO)

YES

FAST TEST SWITCH (TSL)

INITIATES A TEST WITH LOAD, USING FIXED (SMALL) TIME DELAY SETTINGS

HOME-->EXERSISER-->TEST-->FASTTEST or GREEN 'TEST' PUSHBUTTON THEN 'FASTTEST'

N/A N/A NO

TEST WITH LOAD (TSNL)

INITIATES A TEST WITH LOAD, USING SAME TIME DELAY SETTINGS AS THOSE FOR ACTUAL OUTAGE CONDITION

HOME-->EXERSISER-->TEST-->XFERLOAD or GREEN 'TEST' PUSHBUTTON THEN 'XFERLOAD'

N/A N/A YES

TEST NO LOAD

INITIATES A STARTING OF GENERATOR BY ATS, BUT NO TRANSFER OF LOAD AWAY FROM PREFERRED SOURCE

HOME-->EXERSISER-->TEST-->NOXFER or GREEN 'TEST' PUSHBUTTON THEN 'NOXFER'

N/A N/A YES

AUTO/ MANUAL SELECT SWITCH (S5, S12)

IF SET TO "AUTO": SWITCH WILL AUTOMATICALY CONNECT TO THE SOURCES UPON EXPIRATION OF ASSOCIATED TIME DELAYS IF SET TO "MANUAL S2 TO S1 ONLY (S5)" SWITCH WILL NOT AUTOMATICALLY RETURN TO PREFERRED SOURCE. SWITCH WILL WAIT FOR OPERATOR TO GIVE PERMISSIVE [SOFT SWITCH ON STATUS SCREEN] OR RECEIPT OF USER CONFIGURABLE CUSTOMER INPUT CONFIGURED TO "MANUAL XFER S2 TO S1 (S5)" FEATURE IF SET TO "MANUAL S1 TO S2, S2 TO S1 (S12)" SWITCH WILL NOT AUTOMATICALLY CONNECT TO THE NON-PREFERRED SOURCE, OR RETURN TO PREFERRED SOURCE. SWITCH WILL WAIT FOR OPERATOR TO GIVE PERMISSIVE [SOFT SWITCH ON STATUS SCREEN] OR RECEIPT OF USER CONFIGURABLE CUSTOMER INPUT CONFIGURED TO "MANUAL XFER S1 -2 AND S2-1 (S12)" FEATURE


"AUTO", "MANUAL S1 TO S2, S2 TO S1 (S12)", "MANUAL S2 TO S1 ONLY (S5)"

AUTO YES

TRANSFER MODE SELECT (TMS) SWITCH

PROVIDES USER SELECTION OF THE TRANSFER MODE. IF SET TO ‘CLOSED’, SWITCH WILL OPERATE IN CLOSED TRANSITION (MAKE-BEFORE-BREAK) OPERATION. IF SET TO ‘DELAYED’, SWITCH WILL OPERATE AS A DELAYED TRANSITION SWITCH, WITH A PROGRAMMED CENTER/OFF POSITION AND ASSOCIATED TIMER SETTINGS.


CLOSED or DELAYED CLOSED YES

THE FOLLOWING SETTINGS AND ADJUSTMENTS ARE AVAILABLE WITHIN THE ZTE TRANSFER SWITCH. REFER TO THE ZTE OPERATIONS AND MAINTENANCE MANUAL FOR ADDITIONAL DETAILS. 12.0 DRAWING LEGEND

ITEM/SYMBOL

NOTE: SWITCH NOMINAL VOLTAGE AND FREQUENCY SETTINGS ARE INDICATED ON THE NAMEPLATE.

DESCRIPTION AC CONNECTION PLUG AUX CONNECTION PLUG A3-1,2,3 SOURCE 2 POSITION CONTACT A4-1,2,3 SOURCE 1 POSTION CONTACT CE SOURCE 2 MAIN TRANSFER OPRATOR CEO SOURCE 2 OPEN MAIN TRANSFER OPRATOR CN SOURCE 1 MAIN TRANSFER OPRATOR SEO SOURCE 1 OPEN MAIN TRANSFER OPRATOR CPU CENTRAL PROCESSING UNIT CT1,2,3 CURRENT TRANSFORMER CTTB CURRENT TRANSFORMER TERMINAL BLOCK CV CONTROL VOLTAGE DC CONNECTION PLUG DS DISCONNECT SWITCH E1,2,3 SOURCE 2 EMERGENCY LINE EN SOURCE 2 EMERGENCY NEUTRAL LINE K- CARD MX350 NON CONFIGURABLE INPUT/OUTPUT CARD L-CARD MX350 CONFIGURABLE INPUT/OUTPUT CARD N1,2,3 SOURCE 1 EMERGENCY LINE NN SOURCE 1 EMERGENCY NEUTRAL LINE OIP OPERATOR INTERFACE PANEL PA3 CONNECTION PLUG PSU MX350 POWER SUPPLY MODULE Q2 REMOTE SYSTEM TEST CONTACT RCE RECTIFIER CAPACITOR, EMERGENCY RCN RECTIFIER CAPACITOR, NORMAL RSS SECONDARY SOLENOID RECTIFIER SCR-E SILICON CONTROL RECTIFIER, COMMAND TO CLOSE SOURCE 2 SCR-EO SILICON CONTROL RECTIFIER, COMMAND TO OPEN SOURCE 2 SCR-N SILICON CONTROL RECTIFIER, COMMAND TO CLOSE SOURCE 1 SCR-NO SILICON CONTROL RECTIFIER, COMMAND TO OPEN SOURCE 2 SE SOURCE 2 LIMIT SWITCH (CLOSE WHEN ATS IS IN SOURCE 2 POSITION

SOURCE 2 LIMIT SWITCH (CLOSE WHEN ATS IS IN SOURCE 2 OPEN POSITION) SEO

SLE TRANSFER TO EMERGENCY RELAY SLN TRANSFER TO NORMAL RELAY SN SOURCE 1 LIMIT SWITCH (CLOSE WHEN ATS IS IN SOURCE 1 POSITION

SOURCE 1 LIMIT SWITCH (CLOSE WHEN ATS IS IN SOURCE 2 OPEN POSITION) SNO

SOL-1 LIMIT SWITCH SOLENOID, SOURCE 1 SOL-2 LIMIT SWITCH SOLENOID, SOURCE 2 SS SECONDARY SOLENOID T1,2,3 LOAD LINES TN LOAD NEUTRAL LINE UTA UNIVERSAL TRANSFORMER ASSEMBLY VT1 SOURCE 1 VOLTAGE SENSING CARD VT2 SOURCE 2 VOLTAGE SENSING CARD

GE ZENITH ZTE SERIES TRANSFER SWITCHES GE ZENITH ZBTECT SERIES TRANSFER SWITCHES - CLOSE TRANSITION TYPE - 4000A

ZTE SERIES CATALOG NUMBER SCHEME, USER CONFIGURABLE I/O 14.0 USER CONFIGURABLE I/O


REVISION: A ECN : S-8713 THIS DRAWING CONTAINS PROPRIETARY AND CONFIDENTIAL INFORMATION. DUPLICATION, REPRODUCTION OR USE OF THIS DOCUMENT OR ITS CONTENTS IN ANY FORM



DESCRIPTION : ESTABLISHED JOB/MODEL : ZBTECT ZBTECT 4000 AMP

DRAWING NUMBER:

96A-4000 3 OF 12 REV:

A

SOURCE 1 FAILURE OUTPUT A1 OUTPUT 1 OUTPUT 1 OUTPUT 1 OUTPUT 1 OUTPUT 1 SOURCE 2 FAILURE OUTPUT A1E OUTPUT 2 OUTPUT 2 OUTPUT 2 OUTPUT 2 OUTPUT 2 CONNECTED TO SOURCE 1 OUTPUT A4 * * * OUTPUT 12 * CONNECTED TO SOURCE 2 OUTPUT A3 * * * OUTPUT 11 * CONNECTED TO CENTER (DELAY TYPE ATS ONLY) OUTPUT A34N * * * * * BYPASS ATS ON SOURCE 1 (BYPASS ATS ONLY) OUTPUT AB3, AB4 * * * * * SWITCH EXERCISING OUTPUT ACTIVE WHEN SWITCH IN EXERCISE MODE OUTPUT EXC * * OUTPUT 6 OUTPUT 6 * ENGINE START SIGNAL ACTIVE OUTPUT ESS * * * * * AUTO TRANSFER OCCURRED – S1 S2 OR S2 S1 OUTPUT ATS2, ATS1 * * * * N/A MANUAL TRANSFER TO S2 OCCURED OUTPUT MTS2S1 N/A N/A N/A N/A OUTPUT 3 MANUAL TRANSFER TO S1 OCCURED OUTPUT MTS1S2 N/A N/A N/A N/A OUTPUT 4 TRANSFER INHIBIT (S2 TO S1, OR S1 TO S2) ON OUTPUT TIS2S1, TIS1S2 * * * * N/A COMMON ALARM (ANY ALARM ACTIVE) OUTPUT ALM * * OUTPUT 7 OUTPUT 7 * FAIL TO TRANSFER TO SOURCE 1 ALARM POSTIVE INDICATION OF XFER NOT RECEIVED BY CONTROL OUTPUT FTS1 * * * OUTPUT 9 * FAIL TO TRANSFER TO SOURCE 2 ALARM OUTPUT FTS2 OUTPUT 3 OUTPUT 3 OUTPUT 3 OUTPUT 3 * ATS NOT IN AUTO SWITCH IS INIHIBITED FROM AUTO OPERATION OUTPUT NIA * * OUTPUT 8 OUTPUT 8 N/A TRANSFER TO SOURCE 2 ALARM (CHICAGO/CTAP) OUTPUT CTAP * * * * * REMOTE ENGINE START ATS WILL RESPOND WITH START SIGNAL TO GEN INPUT RES INPUT 4 INPUT 4 INPUT 4 INPUT 4 INPUT 4 NO LOAD TEST ATS WILL START GEN, BUT NOT TRANSFER LOAD INPUT TSNL * * * * Input 3 BYPASS TIME DELAY ON TRANSFER TO SOURCE 1 WILL CAUSE IMMEDIATE CONNECTION TO SOURCE 1 INPUT BYPTR INPUT 1 INPUT 1 INPUT 1 INPUT 1 N/A BYPASS TIME DELAY ON TRANSFER TO SOURCE 2 WILL CAUSE IMMEDIATE CONNECTION TO SOURCE 1 INPUT BYPWR * * INPUT 5 INPUT 5 N/A INHIBIT TRANSFER TO SOURCE 1 WILL IHHIBIT ATS FROM CONNECTING LOAD TO SOURCE 1 INPUT Q7 INPUT 3 INPUT 3 INPUT 3 INPUT 3 N/A INHIBIT TRANSFER TO SOURCE 2 WILL IHHIBIT ATS FROM CONNECTING LOAD TO SOURCE 2 INPUT Q3 INPUT 2 INPUT 2 INPUT 2 INPUT 2 N/A AUTO/MAN TRANSFER SELECT - SOURCE 2 TO SOURCE 1 REMOTE CONTROL OF AUTO/MAN SWITCH INPUT S5R * * * * N/A MANUAL RE-TRANSFER TO SOURCE 1 PERMISSIVE SIGNAL TO TRANSFER IN MANUAL MODE INPUT YNR * * INPUT 8 INPUT 8 INPUT 2 AUTO/MAN TRANSFER SELECT - SOURCE 2 TO SOURCE 1 AND SOURCE 1 TO SOURCE 2

REMOTE CONTROL OF AUTO/MAN SWITCH INPUT S12R * * INPUT 6 INPUT 6 N/A

MANUAL RE-TRANSFER TO SOURCE 2 PERMISSIVE SIGNAL TO TRANSFER IN MANUAL MODE INPUT YER * * INPUT 7 INPUT 7 INPUT 2 PRIME SOURCE SELECTION REMOTE SELECTION OF PRIME SOURCE INPUT S3R * * * INPUT 12 N/A COMMIT/NO COMMIT TO TRANSFER TO SOURCE 2 REMOTE SELECTION OF COMMIT/NO COMMIT XFER INPUT S13R * * * * N/A PROGRAMMABLE LOAD CONTROL RELAY #1 PROG. AS ELEVATOR PRE-SIGNAL OR LOAD DISC. OUTPUT LCE1, LCL1 OUTPUT 4 OUTPUT 4 OUTPUT 4 OUTPUT 4 * PROGRAMMABLE LOAD CONTROL RELAY #2 PROG. AS ELEVATOR PRE-SIGNAL OR LOAD DISC. OUTPUT LCE2, LCL2 * * OUTPUT 5 OUTPUT 5 * PROGRAMMABLE LOAD CONTROL RELAY #3-#6 PROG. AS ELEVATOR PRE-SIGNAL OR LOAD DISC. OUTPUT LCE3-6, LCL3-6 * * * * * AUTO LOAD SHED – REMOTE RESET REMOTE RESET FOR LATCHED AUTO LOAD SHED OUTPUT ALS N/A * * OUTPUT 10 N/A

AUTO LOAD SHED – LOCAL/REMOTE SELECT REMOTE SELECTION TO SHED ATS OR PICKUP CONTROL

RELAY ON ACTIVATION OF AUTO LOAD SHED INPUT

LS1R N/A * * INPUT 9 N/A AUTO LOAD SHED – KW BYPASS ENABLE/DISABLE ALS PICKUP ON OVER KW INPUT LS1KW N/A * * INPUT 10 N/A SOURCE 1 (OR SOURCE 2) UNDERVOLTAGE UVS1, UVS2 N/A * * * N/A SOURCE 1 (OR SOURCE 2) OVERVOLTAGE OUTPUT OVS1/2 N/A * * * N/A SOURCE 1 (OR SOURCE 2) UNDERFREQUENCY UFS1, UFS2 N/A * * * N/A SOURCE 1 (OR SOURCE 2) OVERFREQUENCY OUTPUT OFS1/2 N/A * * * N/A LOW PF ALARM OUTPUT LLPFA N/A * * * N/A

SOURCE 1 (OR SOURCE 2) VOLTAGE THD% ALARM OUTPUT VTHDS1, VTHDS2 N/A * * * N/A

LOAD CURRENT THD% ALARM OUTPUT CTA N/A * * * N/A LOAD KW (OVERLOAD) ALARM OUTPUT LOKWA N/A * * * N/A

OVERCURRENT ALARM (PHASE A, B, C, OR N) OUTPUT OCAPA/B/C,

NOCA N/A * * * N/A SOURCE 1 (OR SOURCE 2) VOLTAGE IMBALANCE OUTPUT VIAS1, VIAS2 N/A * * * N/A LOAD CURRENT UNBALANCE ALARM OUTPUT CIA N/A * * * N/A DIGITAL INPUTS (UP TO 10) FOR USER CONFIG ALARMS &/OR FLEXLOGIC

UP TO 10 ALARMS, ACTIVATED BY INPUTS & TIME DELAY SETTING. INCLUDE USER-PROG MESSAGE DISPLAY INPUT CCDI-x N/A * * * N/A

USER CONFIG DIGITAL ALARMS OUTPUT CONTACT FOR PROGRAMMED DIGITAL ALARMS OUTPUT CCAD-x N/A * * * N/A

SOURCE STATUS

SWITCH POSITION

SWITCH STATUS & DIAGNOSTICS

REMOTE CONTROL/ BUILDING

INTERFACE

PROGRAMMABLE LOAD CONTROL

RELAYS

AUTO LOAD SHED

USER CONFIGURABLE

ANALOG ALARMS

USER CONFIGURABLE

DIGITAL ALARMS

FACTORY DEFAULT I/O CONFIGURATION

FEATURE EXTENDED DESCRIPTION TYPE

(INPUT/ OUTPUT)

"A" "B" "C" "D" "M" RECORD 4 IN/

4 OUT 4 IN/

4 OUT 8 IN/

8 OUT 12 IN/

12 OUT 4 IN/

4 OUT SITE

SETTING

ZTE SWITCHES INCLUDE USER CONFIGURABLE INPUTS & OUTPUTS (I/O) THAT MAY BE FIELD-RECONFIGURED TO MEET SITE NEEDS. THE AMOUNT OF I/O DEPENDS ON THE INSTALLED CONTROL CONFIGURATION GROUP (SEE TABLE BELOW) CONFIGURATION OF THE I/O AT TIME OF FACTORY SHIPMENT IS SHOWN ON THE NAMEPLATE ADJACENT TO THE CUSTOMER CONNECTIONS TERMINAL STRIP AND THE ATTACHED TABLE. NEW CONTROL FEATURES MAY BE ADDED IN FIELD BY SETTING THE CURRENT CONTROL FEATURE I/O ADDIGNEMENT TO “N/A” AND RE-ALLOCATING THE I/O POINT TO A NEW FEATURE. SEE O&M MANUAL FOR COMPLETE PROCEDURE FOR I/O RE-ASSIGNMENT AND LIST OF AVAILABLE FEATURES.

OPTION CODE

13.0 ATS CATALOG NUMBER SCHEME

Z1 0 A 2 S 1 A A 1 0 A X X X X XX DIGIT #1, #2 PRODUCT TYPE Z1 - ATS Z2 - BYPASS ATS DIGIT #3 OPERATION O – OPEN TRANSITION D – DELAYED TRANSITION C – CLOSED TRANSITION DIGIT #4 AMPERE RATING A – 40A B - 80A C – 100A, D – 150A, F – 225A G- 260A, I – 400A, J-600A, K-800A, L-1000A M-1200A, N-1600A, O-2000A, Q-3000A,

R-4000A DIGIT #5 # POLES 2 – 2 POLE, 3- 3 POLE, 4- 4 POLE DIGIT #6 APPLICATION/SOURCE TYPES S – UTILITY TO GENERATOR

U – UTILTY TO UTILITY G – GENERATOR TO GENERATOR

DIGIT #7 1 DIGIT #8 ENCLOSURE TYPE

X - OPEN (NONE), A – NEMA 1, B –NEMA 1A C – NEMA 3R, D – NEMA 3R W/ HEATER E – NEMA 4, F – NEMA 12, G – NEMA 4X

DIGIT #9 CONTROL OPTION PACKAGE

A, B, C, OR D: SEE SHEET #1 FOR DESCRIPTION DIGIT #10,#11 VOLTAGE RATING

2-DIGIT FACTORY CODE. SEE ATS NAMEPLATE FOR RATED VOLTAGE

DIGIT #12 LUG OPTIONS

2-DIGIT FACTORY CODE. SEE O&M MANUAL FOR DETAILS

DIGIT #13 METERING & ACCESSORIES CODE

‘A’ THRU ‘O” OR X. SEE SHEET #1 FOR FURTHER DETAILS

DIGIT #14 COMMUNICATIONS OPTIONS CODE ‘X’, ‘S’, OR ‘E’. SEE SHEET #1 FOR FURTHER DETAILS

DIGIT #15 GROUND BUS OPTIONS CODE ‘X’, OR 1-8. SEE O&M FOR DETAILS

DIGIT #16 TVSS OPTIONS CODE ‘X’, OR ‘A-G’. SEE O&M FOR DETAILS

DIGIT #17 BATTERY CHARGER OPTION CODE

‘X’, OR ‘1-4’. SEE O&M FOR DETAILS DIGIT #18 ‘X’

Documents

CONFIGURATION DESCRIPTION RELATED …apps.geindustrial.com/publibrary/checkout/96A-4000?TNR=Electrical... · 1.0 control configuration groups ... user-configurable analog & digital