Conf Sw Routers (1)

Router#CONF T Enter configuration commands, one per line. End with CNTL/Z. Router(config)#HOST R-IBERO1 R-IBERO1(config)#INT S0/2/0 R-IBERO1(config-if)#IP ADD 192.168.3.1 255.255.255.252 R-IBERO1(config-if)#NO SHUTD %LINK-5-CHANGED: Interface Serial0/2/0, changed state to down R-IBERO1(config-if)#EXIT R-IBERO1(config)#INT FA0/0 R-IBERO1(config-if)#NO IP ADD R-IBERO1(config-if)#INT FA0/0.10 R-IBERO1(config-subif)#ENCAP DOT1Q 10 R-IBERO1(config-subif)#IP ADD 10.10.10.1 255.255.255.0 R-IBERO1(config-subif)#INT FA0/0.20 R-IBERO1(config-subif)#ENCAP DOT1Q 20 R-IBERO1(config-subif)#IP ADD 10.10.20.1 255.255.255.0 R-IBERO1(config-subif)#INT FA0/0.50 R-IBERO1(config-subif)#ENCAP DOT1Q 50 R-IBERO1(config-subif)#IP ADD 10.10.50.1 255.255.255.0 R-IBERO1(config-subif)#EXIT R-IBERO1(config)#INT FA0/0 R-IBERO1(config-if)#NO SHUTD R-IBERO1(config-if)# %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state t o up %LINK-5-CHANGED: Interface FastEthernet0/0.10, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.10, changed stat e to up %LINK-5-CHANGED: Interface FastEthernet0/0.20, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.20, changed stat e to up %LINK-5-CHANGED: Interface FastEthernet0/0.50, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.50, changed stat e to up R-IBERO1(config-if)#EXIT R-IBERO1(config)#ROUTER RIP R-IBERO1(config-router)#VERSION 2 R-IBERO1(config-router)#NET 192.168.3.0 R-IBERO1(config-router)#NET 10.10.10.0 R-IBERO1(config-router)#NET 10.10.20.0 R-IBERO1(config-router)#NET 10.10.50.0 R-IBERO1(config-router)#NO AUTO-SUMMARY R-IBERO1(config-router)#EXIT R-IBERO1(config)#IP DHCP POOL FINANZAS R-IBERO1(dhcp-config)#NET 10.10.10.0 255.255.255.0 R-IBERO1(dhcp-config)#DEFAULT-ROUTER 10.10.10.1 R-IBERO1(dhcp-config)#OPTION 150 IP 10.10.10.1 R-IBERO1(dhcp-config)#EXIT R-IBERO1(config)#IP DHCP EXCLUDED-ADD 10.10.10.1 10.10.10.150

R-IBERO1(config)#IP DHCP POOL RECURSOS R-IBERO1(dhcp-config)#NET 10.10.20.0 255.255.255.0 R-IBERO1(dhcp-config)#DEFAULT-ROUTER 10.10.20.1 R-IBERO1(dhcp-config)#OPTION 150 IP 10.10.20.1 R-IBERO1(dhcp-config)#EXIT R-IBERO1(config)#IP DHCP EXCLUDED-ADD 10.10.20.1 10.10.20.100 R-IBERO1(config)#IP DHCP POOL VOICE1 R-IBERO1(dhcp-config)#NET 10.10.50.0 255.255.255.0 R-IBERO1(dhcp-config)#DEFAULT-ROUTER 10.10.50.1 R-IBERO1(dhcp-config)#OPTION 150 10.10.50.1 ^ % Invalid input detected at '^' marker. R-IBERO1(dhcp-config)# R-IBERO1(dhcp-config)#OPTION 150 IP 10.10.50.1 R-IBERO1(dhcp-config)#EXIT R-IBERO1(config)#IP DHCP EXCLUDED-ADD 10.10.50.1 10.10.50.50 R-IBERO1(config)#TELEFONY-SERVICE ^ % Invalid input detected at '^' marker. R-IBERO1(config)#TELEPHONY-SERVICE R-IBERO1(config-telephony)#MAX-EPHONE 3 R-IBERO1(config-telephony)#MAX-DN 3 R-IBERO1(config-telephony)#? auto Define dn range for auto assignment auto-reg-ephone Enable Ephone Auto-Registration create create cnf for ethernet phone exit Exit from telephony config mode ip Define IP address and port for Telephony-Service/Fallback keepalive Define keepalive timeout period to unregister IP phones max-dn Maximum directory numbers supported max-ephones Define max number of IP phones no Negate or set default values of a command R-IBERO1(config-telephony)#AUTO ASSIGN 1 TO 5 R-IBERO1(config-telephony)#IP SOURCE-ADD 10.10.50.1 PORT 2000 R-IBERO1(config-telephony)#EXIT R-IBERO1(config)#EPHONE-DN 1 R-IBERO1(config-ephone-dn)#%LINK-3-UPDOWN: Interface ephone_dsp DN 1.1, changed state to up R-IBERO1(config-ephone-dn)#NUMBER 2222 R-IBERO1(config-ephone-dn)#EXIT R-IBERO1(config)#EPHONE-DN 2 R-IBERO1(config-ephone-dn)#%LINK-3-UPDOWN: Interface ephone_dsp DN 2.1, changed state to up R-IBERO1(config-ephone-dn)#NUMBER 3333 R-IBERO1(config-ephone-dn)#EXIT R-IBERO1(config)#EPHONE-DN 3 R-IBERO1(config-ephone-dn)#%LINK-3-UPDOWN: Interface ephone_dsp DN 3.1, changed state to up R-IBERO1(config-ephone-dn)#NUMBER 4444 R-IBERO1(config-ephone-dn)#EXIT Switch>ENA Switch#CONF T Enter configuration commands, one per line. End with CNTL/Z.

Switch(config)#HOST SW1 SW1(config)#INT RANGE FA0/1-9 SW1(config-if-range)#SWITCHPORT MODE TRUNK

SW1(config-if-range)# %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state t o down %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state t o up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state t o down %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state t o up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed state t o down %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed state t o up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/4, changed state t o down %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/4, changed state t o up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/5, changed state t o down %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/5, changed state t o up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/6, changed state t o down %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/6, changed state t o up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/7, changed state t o down %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/7, changed state t o up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/8, changed state t o down %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/8, changed state t o up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/9, changed state t o down %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/9, changed state t o up SW1(config-if-range)#EXIT SW1(config)#INT FA0/15 SW1(config-if)#SWITCHPORT VOICE VLAN 50 SW1(config-if)#EXIT SW1(config)#VLAN 10 SW1(config-vlan)#NAME FINANZAS SW1(config-vlan)#EXIT SW1(config)#VLAN 20 SW1(config-vlan)#NAME RECURSOS SW1(config-vlan)#EXIT SW1(config)#VLAN 50 SW1(config-vlan)#NAME VOICE1 SW1(config-vlan)#EXIT SW1(config)#VTP MODE SERVER Device mode already VTP SERVER. SW1(config)#VTP DOMAIN IBERO Changing VTP domain name from NULL to IBERO SW1(config)#VTP PASS CISCO1 Setting device VLAN database password to CISCO1 SW1(config)#INT RANGE FA0/2-5 SW1(config-if-range)#CHANNEL-PROTOCOL PAGP SW1(config-if-range)#CHANNEL-GROUP 1 MODE DESIRABLE SW1(config-if-range)# Creating a port-channel interface Port-channel 1 %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state t o down %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state t o up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed state t o down %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed state t o up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/4, changed state t o down %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/4, changed state t o up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/5, changed state t o down %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/5, changed state t o up SW1(config-if-range)#exit SW1(config)#exit SW1# %SYS-5-CONFIG_I: Configured from console by console

SW1#wr Building configuration... [OK] SW1# SW1#conf t Enter configuration commands, one per line. End with CNTL/Z. SW1(config)#INT RANGE FA0/6-9 SW1(config-if-range)#CHANNEL-PROTOCOL PAGP SW1(config-if-range)#CHANNEL-GROUP 2 MODE DESIRABLE SW1(config-if-range)# Creating a port-channel interface Port-channel 2 %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/6, changed state t o down %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/6, changed state t o up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/7, changed state t o down %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/7, changed state t o up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/8, changed state t o down %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/8, changed state t o up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/9, changed state t o down %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/9, changed state t o up SW1(config-if-range)#EXIT SW1(config)#EXIT SW1# %SYS-5-CONFIG_I: Configured from console by console SW1#WR Building configuration... [OK] SW1#

Switch>ENA Switch#CONF T Enter configuration commands, one per line. End with CNTL/Z. Switch(config)#HOST SW2 SW2(config)#INT RANGE FA0/2-5 SW2(config-if-range)#SWITCHPORT MODE TRUNK SW2(config-if-range)#CHANNEL-PROTOCOL PAGP SW2(config-if-range)#CHANNEL-GROUP 1 MODE DESIRABLE SW2(config-if-range)# Creating a port-channel interface Port-channel 1 %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state t o down

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state t o up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed state t o down %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed state t o up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/4, changed state t o down %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/4, changed state t o up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/5, changed state t o down %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/5, changed state t o up %LINK-5-CHANGED: Interface Port-channel 1, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface Port-channel 1, changed state to up SW2(config-if-range)#EXIT SW2(config)#INT FA0/15 SW2(config-if)#SWITCHPORT VOICE VLAN 50 SW2(config-if)#EXIT SW2(config)#INT FA0/20 SW2(config-if)#SWITCHPORT MODE ACCESS SW2(config-if)#SWITCHPORT ACCESS VLAN 10 % Access VLAN does not exist. Creating vlan 10 SW2(config-if)#EXIT SW2(config)#VTP MODE CLIENT Setting device to VTP CLIENT mode. SW2(config)#VTP DOMAIN IBERO Domain name already set to IBERO. SW2(config)#VTP PASS CISCO1 Setting device VLAN database password to CISCO1 SW2(config)#INT FA0/20 SW2(config-if)#SWITCHPORT ACCESS VLAN 10 SW2(config-if)#EXIT SW2(config)#DO SH VLAN BRIEF VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------1 default active Fa0/1, Fa0/6, Fa0/7, Fa0/8 Fa0/9, Fa0/10, Fa0/11, Fa0/12 Fa0/13, Fa0/14, Fa0/15, Fa0/16 Fa0/17, Fa0/18, Fa0/19, Fa0/21 Fa0/22, Fa0/23, Fa0/24, Gig1/1 Gig1/2 10 VLAN0010 active Fa0/20 50 VLAN0050 active 1002 fddi-default active 1003 token-ring-default active 1004 fddinet-default active

1005 trnet-default active SW2(config)#INT FA0/13 SW2(config-if)#SWITCHPORT MODE ACCESS SW2(config-if)#SWITCHPORT ACCESS VLAN 20 SW2(config-if)#EXIT SW2(config)#DO SH VLAN BRIEF VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------1 default active Fa0/1, Fa0/6, Fa0/7, Fa0/8 Fa0/9, Fa0/10, Fa0/11, Fa0/12 Fa0/14, Fa0/15, Fa0/16, Fa0/17 Fa0/18, Fa0/19, Fa0/21, Fa0/22 Fa0/23, Fa0/24, Gig1/1, Gig1/2 10 VLAN0010 active Fa0/20 50 VLAN0050 active 1002 fddi-default active 1003 token-ring-default active 1004 fddinet-default active 1005 trnet-default active SW2(config)# SW2#WR Building configuration... [OK] SW2# Switch>ENA Switch#CONF T Enter configuration commands, one per line. End with CNTL/Z. Switch(config)#HOST SW3 SW3(config)#INT RANGE FA0/6-9 SW3(config-if-range)#SWITCHPORT MODE TRUNK SW3(config-if-range)#CHANNEL-PROTOCOL PAGP SW3(config-if-range)#CHANNEL-GROUP 1 MODE DESIRABLE SW3(config-if-range)# Creating a port-channel interface Port-channel 1 %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/6, changed state t o down %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/6, changed state t o up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/7, changed state t o down %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/7, changed state t o up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/8, changed state t o down %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/8, changed state t o up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/9, changed state t o down %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/9, changed state t

o up %LINK-5-CHANGED: Interface Port-channel 1, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface Port-channel 1, changed state to up SW3(config-if-range)#EXIT SW3(config)#INT FA0/15 SW3(config-if)#SWITCHPORT VOICE VLAN 50 SW3(config-if)#EXIT SW3(config)#VTP MODE CLIENT Setting device to VTP CLIENT mode. SW3(config)#VTP DOMAIN IBERO Domain name already set to IBERO. SW3(config)#VTP PASS CISCO1 Setting device VLAN database password to CISCO1 SW3(config)#INT FA0/18 SW3(config-if)#SWITCHPORT MODE ACCESS SW3(config-if)#SWITCHPORT ACCESS VLAN 10 SW3(config-if)#EXIT SW3(config)#INT FA0/17 SW3(config-if)#SWITCHPORT MODE ACCESS SW3(config-if)#SWITCHPORT ACCESS VLAN 20 SW3(config-if)#EXIT SW3(config)#EXIT SW3# %SYS-5-CONFIG_I: Configured from console by console SW3#WR Building configuration... [OK] SW3#

Router>ENA Router#CONF T Enter configuration commands, one per line. End with CNTL/Z. Router(config)#HOST R-IBEROX R-IBEROX(config)#INT S0/2/0 R-IBEROX(config-if)#IP ADD 192.168.3.2 255.255.255.252 R-IBEROX(config-if)#CLOCK RATE 64000 R-IBEROX(config-if)#NO SHUTD R-IBEROX(config-if)# %LINK-5-CHANGED: Interface Serial0/2/0, changed state to up R-IBEROX(config-if)#EXIT R-IBEROX(config)#IN %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/2/0, changed state to up % Ambiguous command: "I" R-IBEROX(config)#INT S0/2/1 R-IBEROX(config-if)#IP ADD 192.168.2.1 255.255.255.252 R-IBEROX(config-if)#CLOCK RATE 64000 R-IBEROX(config-if)#NO SHUTD %LINK-5-CHANGED: Interface Serial0/2/1, changed state to down R-IBEROX(config-if)#EXIT

R-IBEROX(config)#INT S0/0/0 R-IBEROX(config-if)#IP ADD 192.168.1.1 255.255.255.252 R-IBEROX(config-if)#NO SHUTD %LINK-5-CHANGED: Interface Serial0/0/0, changed state to down R-IBEROX(config-if)#EXIT R-IBEROX(config)#ROUTER RIP R-IBEROX(config-router)#VER 2 R-IBEROX(config-router)#NO AUTO-SUMMARY R-IBEROX(config-router)#NET 192.168.3.0 R-IBEROX(config-router)#NET 192.168.2.0 R-IBEROX(config-router)#PASSIVE-INTERFACE S0/0/0 R-IBEROX(config-router)#REDISTRIBUTE STATIC R-IBEROX(config-router)#EXIT R-IBEROX(config)#IP ROUTE 0.0.0.0 0.0.0.0 S0/0/0 R-IBEROX(config)#EXIT R-IBEROX# %SYS-5-CONFIG_I: Configured from console by console R-IBEROX#WR Building configuration... [OK] R-IBEROX#

Documents

Conf Sw Routers (1)