Concrete and Masonry Tools - CS Unitec€¦ · Rotary Hammer Drills (Air • Hydraulic) p. 19 Powerful percussion for drilling concrete and masonry. SDS Plus and SDS Max chucks. Hammer

2 • 1-800-700-5919 • Visit our Web site at www.csunitec.com

Concrete and Masonry Tools

CS Unitec's Trelawny™ line of surface preparation tools features manyVibro-Lo™ models. These models include integrated vibration reductiontechnology to operate with 7x less vibration than standard models.Vibration damping components offset the hammer vibration when the toolimpacts the workpiece, reducing the risk of vibration-related injury.

Heavy-Duty Hand-Held Scabblers (Pneumatic) p. 5

• Low-Vibration Single-Head and Triple-Head Scabbling Hammers

• Roughen, reduce and level concrete; prepare cracks for repair

• Optional vacuum shroud for dust extraction

Multi-Headed Floor Scabblers (Pneumatic) p. 6-7

• Vibro-Lo™ 11-head model for concrete keying, laitance removal and less-aggressive material removal to protect substrate below

• 5-head model for fast concrete removal and demolition when leveling high spots, texturing and roughening for sealant/overlay preparation and breaking down hard coatings prior to blast cleaning

Vibro-Lo™Vibration Reduction

Technology

Floor Scarifiers / Planers (Electric • Pneumatic • Gas) p. 8

• Ideal for the most demanding surface preparation and material removal applications

• Remove rust, scale, paint, adhesives and more from steel and concrete

Long-Reach Chisels / Scrapers / Scalers (Pneumatic) p. 14

• Available in lengths ranging from 2' to 6'; chip, scrape and descale with one tool

Surface Preparation Tools & Dust Collection Vacuums

• HEPA filtration for cleaner, safer work environment

• "Power Take Off" outlet for ON/OFF activation from power tool switch

• Standard wet/dry models available

Hand-Held Construction Scabblers (Pneumatic) p. 4

Dust Collection Vacuums with HEPA Filtration p. 15

• Low-vibration hand-held and walk-behind grinders

• 5", 7" and 9" models

Concrete Grinders p. 15

• Low-Vibration Single-Head and Triple-Head Scabbling Hammers

• Roughen, reduce and level concrete

• Prepare surfaces for coatings and finishes

Vibro-Lo™Vibration Reduction Technology



Low-Vibration Needle/Chisel Scalers (Pneumatic) p. 10-13

• Vibro-Lo™ Needle/Chisel Scalers remove coatings, corrosion and other accumulated materials

• Clean and stress-relieve weld seams and joints

• Variety of needles and chisels, including options for use in hazardous areas and Ex zones


GRINDER

S

SCARIFIER

S

CHISEL SCALERSCABBLER

Hand-Held Scarifiers – Rotopeen™ (Pneumatic • Electric) p. 9

• Ideal alternative to small-area shot blasting – clean/prepare steel and concrete surfaces

• Available with 3M's Rotopeen™ 'C' flaps, star cutters and beam cutters

3• 1-800-700-5919 • Visit our Web site at www.csunitec.com

Core Drilling, Hammer Drilling, Mixing, Sawing & MoreWet / Dry Diamond Core Drills (Electric • Air • Hydraulic) p. 16-18Drill holes from 1/8" to 18" dia. in floors, walls and ceilings. Fast drilling of reinforced concrete, concrete, brick, block and stone. Wet/dry models with dust collection port. Water recycling and slurry containment vacuum.

Rotary Hammer Drills (Air • Hydraulic) p. 19Powerful percussion for drilling concrete and masonry. SDS Plus and SDS Max chucks. Hammer drill holes in concrete, brick and masonry. Rotary drilling for straight drilling of steel and wood.

Mixing Drills and Mixing Stations (Electric • Pneumatic) p. 20-21Professional variable-speed, high-torque models for fast, efficient mixing. Hand-held models for batches up to 5 bag/35 gallons. Variety of galvanized steel mixing paddles and portable mixing stands and stations for running mixers independently.

HIPPO Mixing Station p. 21Mix, transport and pour with one unit. Casters or tires for varying jobsite terrain. Removable liner for mixing multiple batches and extending life of bucket.

Concrete Hand-Held and Walk-Behind Cut-Off Saws (Air) p. 22Wet or dry cutting of concrete, reinforced concrete, asphalt, masonry, steel and more. Low maintenance – no belts, pistons, fuel lines or carburetors to maintain. Walk-behind saw designed for tough cutting jobs, including joint sawing, floor sawing, trenching, road repair and plant maintenance.

Concrete Circular Saw p. 22Wet or dry cutting stone and masonry materials, including granite, marble, terrazzo and concrete. 7" blade, adjustable cutting depth up to 2-1/3". Vacuum connection.

Wall Slotter p. 22Cut channels up to 1-13/16" wide x 1-3/4" deep in concrete and masonry. Adjustable width and depth. Vacuum connection.

Concrete Chain Saws p. 23Pneumatic and hydraulic diamond concrete chain saws. Deep plunge cuts up to 20" deep and square corners up to 19" with no overcuts. Ideal for mechanical openings and irregular shapes. PowerGrit diamond pneumatic chain saw for ductile iron.

Diamond Saw p. 245" Diamond Saw for wet/dry cutting of hard tile, natural stone and stoneware.

WarrantyProducts of CS Unitec, Inc. are warranted to be free from defects in material and workmanship for one year from date of purchase. This warranty does not apply tonormal wear or products which have been abused, misused, modified or repaired by someone other than CS Unitec, Inc. or its Authorized Service Representatives.If a product proves defective in material or workmanship within one year after purchase, return it to CS Unitec, Inc. or an Authorized Service Center, transportationprepaid. CS Unitec, Inc. will, at its option, repair or replace defective products free of charge.CS Unitec, Inc.'s sole liability and your exclusive remedy under this warranty is limited to repair or replacement of the defective product. There are no other warrantiesexpressed or implied and CS Unitec, Inc. shall not be liable for incidental, consequential or special damages, or expenses excepting only the cost or expense of repairor replacement as described above.

SafetyOperators of any power tool should use appropriate safety precautions for work being performed. This includes safety chains, eye protection, hearing protection,gloves and more. Follow instructions included in operating manual.

CS Unitec’sTrelawny™ Vibro-Lo™ Single-HeadScabbler operateswith 7x less vibrationthan standardmodels. This toolutilizes vibrationdamping componentsto offset the hammervibration createdwhen the headimpacts theworkpiece.

CS Unitec’s Trelawny™ line of pneumatic hand-held constructionscabblers are ideal for roughing and reducing concrete surfacesto remove laitance and coatings and expose aggregate to allowfor proper application of new materials such as textured finishesand waterproofing coatings.

• Single-head scabbler includes integrated Vibro-Lo™vibration reduction technology

• Triple scabbler includes integrated back handle grip forcomfortable operation and control

• Single-piece Tungsten Carbide Tipped pistons withCruciform or Bush heads

Roughen, reduce and level concrete; preparesurfaces for coatings and finishes

Applications include:• Scabbling concrete to expose aggregate• Leveling concrete and block joints• Texturing, roughing and reducing concrete• Preparing for coatings and waterproofing compounds• Bridge maintenance

Hand-Held Construction Scabblers

Scabbling Hammer AccessoriesPart No.

612.6000

612.6010

815.5550

859.1530859.1555

For Model Numbers

151.6170 and 153.6050

161.6171 and 153.6051

151.6171 and 151.6170153.6051 and 153.6050

Single-PieceCruciform Piston

Single-PieceBush Piston

Whip Check

Lubricators


Technology

Vibro-Lo™

Vibro-Lo™

Triple Scabbler includesintegrated back handle gripfor operator comfort andcontrol.

Pneumatic Hand-Held Construction Scabbling Hammers

Pneumatic

TripleHead

Bush Hammer Piston

Cruciform Piston

Bush Hammer Pistons

Cruciform Pistons

153.6051

153.6050

10.5

10.5

19" x 8.6"

19" x 8.6"

8400

8400

16

16

98.5

98.5

41.6

41.6

151.6171

151.6170

6.5

6.5

19" x 6.2"

19" x 6.2"

2800

2800

12

12

98.5

98.5

4.6

4.6

Description

CruciformBush

ModelModel

NumberWeight(lbs.)

Dimensions(LxH)

Blows per

minuteCFM @90 PSI

Noise Leveldb(A)

VibrationLevelsm/s2

SingleHead


Concrete scabblingusing single-head,

Vibro-Lo™Scabbling Hammer

Heavy-Duty Hand-Held Scabblers

Pneumatic

CS Unitec’sTrelawny™ Vibro-Lo™ Single-HeadHeavy-Duty Scabbleroperates with 7x lessvibration thanstandard models.This tool utilizesvibration dampingcomponents to offsetthe hammer vibrationcreated when thehead impacts theworkpiece.

Applications include:• Removing steel scale deposits• Prepare concrete cracks for repair• Texturing, roughing, reducing and leveling concrete• Scabbling concrete to expose aggregate• Preparing for coatings and waterproofing compounds

Concrete scabbling usingsingle-head, Vibro-Lo™Heavy-Duty Scabbler

Heavy-Duty Scabbler AccessoriesPart No.

612.5320

612.5325

815.5550

859.1530859.1555

437.5100437.5300

For Model Numbers

151.5200, 196.5100and 153.5200

151.5250, 196.5105and 153.5250

Single-head ScabblersTriple-head Scabblers

151.5200 and 151.5250153.5200 and 153.5250

Single-PieceCruciform Piston

Single-PieceBush Piston

Whip Check

Lubricators

Vacuum Shroud*

Vibro-Lo™

Vibro-Lo™

Pneumatic Hand-Held Construction Scabbling Hammers

Low-Vibration

Single Head

Triple Head

Bush Hammer Piston

Cruciform Piston

Bush Hammer Pistons

Cruciform Pistons

196.5105

196.5100

5.7

5.7

19" x 6.2"

19" x 6.2"

2900

2900

11.9

11.9

91

91

4.5

4.5

Bush Hammer Pistons

Cruciform Pistons

153.5250

153.5200

11.5

11.5

19" x 6.2"

19" x 6.2"

7200

7200

15.9

15.9

98

98

8.7

8.7

151.5250

151.5200

5.7

5.7

19" x 6.2"

19" x 6.2"

2400

2400

6.5

6.5

94

94

7.0

7.0

DescriptionModelModel

NumberWeight(lbs.)

Dimensions(LxH)

Blows per

minuteCFM @90 PSI

Noise Leveldb(A)

VibrationLevelsm/s2

SingleHead

* Not available for low-vibration models

See page 15 fordust extraction

systems.



Technology

Reduce dust andhazardous particles inwork area with optionalvacuum shroud forHeavy-Duty Hand-HeldScabblers (below).

CS Unitec’s Trelawny™ line of pneumatic heavy-duty hand-held scabblers areideal for more demanding scabbling applications such as the removal of steelscale deposits and the preparation of concrete cracks for repair. These tools alsoreduce, level, texture and roughen concrete, remove coatings and laitance andscabble concrete to expose aggregate for the application of sealants and coatings.

• Single-head heavy-duty scabbler includes integrated Vibro-Lo™ vibration reduction technology

• Triple scabbler offers 7200 blows per minute• Single-piece Tungsten Carbide Tipped pistons with

Cruciform or Bush heads• Optional dust shroud for dust and debris collection

Ideal for more demanding concrete preparationand coating removal applications

Applications include:• Concrete keying• Laitance removal• Situations requiring gentle,

effective scabbling withoutdamaging the substrate below

CS Unitec’s Trelawny™ MHS11 Multi-Headed Concrete Floor Scabbleris a portable, compact, low-vibration machine that covers up to 100 sq. ft./hour.

CS Unitec’s Trelawny™ MHS11 multi-headedconcrete floor scabbler operates with 7x lessvibration than standard models. This tool utilizesa 3-point mechanical vibration damping systemto offset the hammer vibration created when thehead impacts the workpiece.

• Integrated Vibro-Lo™ vibrationreduction technology

• 24,000 light blows per minute

• Built-in dust shroud for dust and debriscollection (model no. 159.6051)

• Low air consumption

Concrete keying and laitanceremoval – 11 heads provide24,000 light blows per minute

11-Head Floor Scabbler - MHS11 Vibro-Lo™Vibration Reduction

Technology

Vibro-Lo™

Vibro-Lo™

MHS11 Low-Vibration Pneumatic Multi-Headed Concrete Floor Scabbler

With Dust Shroudand BushHammer Heads

With BushHammer Heads

159.6051

159.6050

158 11.25" x 13.5"x 50"

24,200 55 97 4.96

Model DescriptionModel

NumberWeight(lbs.)

10"

155 11.25" x 13.5"x 50"

24,200 55 97 4.9610"

CuttingWidth

Dimensions(WxLxH)

Blows per

minuteCFM @90 PSI

Noise Leveldb(A)

VibrationLevelsm/s2

MHS11

MHS11 Accessories Part No.

612.0125

426.5355

426.5358

612.0120

815.5550

859.1580

For Model Numbers

159.6050 and 159.6051

159.6000*

159.6100*

159.6000 and 159.6100*

* Call for details

One-Piece Piston TCT Bush Hammer Head

Replaceable TCT Bush Hammer Cutter Head

Replaceable TCT Cruciform Cutter Head

Piston for Replaceable Cutter Heads

Whip Check

Lubricators

Head Applications:

Bush Hammer Heads areideal for laitance removal;roughing concrete forresurfacing; bridge deckpreparation for waterproofing.

Cruciform Cutter Heads areideal for leveling floors,reducing concrete; removal offloor paints and coatings.Call for details on complete MHS 11 with Cruciform Heads.

Dust PortDust shroud, P/N437.0120, to collect dustand debris when connectedto a dust collectionvacuum. Included withmodel no. 159.6051

See page 15 for dustextraction systems.


PneumaticMHS11

includes dustshroud and

vacuum port(Model no.159.6051)

Multi-Headed Floor Scabbler - MHS5

MHS5 Pneumatic Multi-Headed Concrete Floor Scabbler

MHS55-Point Bush Head

9-Point Bush Head

159.5050

159.5075

251

251

28" x 43" x 38"

28" x 43" x 38"

6500

6500

80

80

94.7

94.7

16.5

16.5

Model DescriptionModel

NumberWeight(lbs.)

11"

11"

CuttingWidth

Dimensions(WxLxH)

Blows per

minuteCFM @90 PSI

Noise Leveldb(A)

VibrationLevelsm/s2

Applications include:• Leveling high spots• Texturing and roughening for

sealant and overlay preparation• Breaking down hard coatings prior

to blast cleaning

CS Unitec’s Trelawny™ MHS5 Multi-Headed Concrete Floor Scabbleris the ultimate demolition tool for quick concrete removal.

• 6500 BPM for fast removal and demolition

• Integrated dust shroud for dust and debris collection

• Large wheels for rough terrain

• Built-in dead man’s handle

Fast concrete removal and demolitionwith integrated dust port

MHS5 Accessories Part No.

441.5360

441.5359

441.5369

815.5550

859.1580

Included

Cruciform Scabbler Head

5-Point Bush Hammer Head

9-Point Bush Hammer Head

Whip Check

Lubricators

Dust Shroud

Head Applications:

Cruciform Scabbler Heads are ideal for leveling floors, reducing concrete and removal of floor paints and coatings.

5-Point Bush Hammer Heads are ideal for laitanceremoval from large floor areas, roughing concrete prior toresurfacing and bridge deck preparation for waterproofing.

9-Point Bush Hammer Heads are ideal for levelinguneven joints and creating excellent bond profiles forepoxies, urethanes and thin overlays.

MHS5 includes integratedvacuum shroud and port.



Applications include:• Removal of rust,

scale, paint, adhesives and more

• Keyed or grooved profiles

• Roughing concrete

CS Unitec’s Trelawny™ Floor Planers tackle the most demandingsurface preparation and material removal applications. Ideal for theremoval of coatings and corrosion from concrete and steel surfacesto prepare for re-coating. Produce an ideal keyed or grooved profileon concrete for waterproofing and non-slip surface applications.

• Depth control maximizes performance and extends cutter life

• Integrated vacuum connection and hold-to-run handle

• Fully adjustable handlebar for operator comfort

• Electric, pneumatic or gas power

Remove rust, scale, paint, adhesivesand more from concrete and steel

Floor Scarifiers - Electric, Pneumatic and Gas

TFP 200 Floor Scarifiers

320.2004T

320.2012T

14" x 35" x 35"1/8"

Model NumberWeight(lbs.)

220V - 240V, 3 HP 8"

CuttingWidth

Dimensions(WxLxH)

Max CuttingDepth per Pass

TFP 200 Electric

14" x 35" x 35"1/8"165CFM @ 90 PSI, 3.5 HP

Motor Specifications

8"

149

99

TFP 200 Pneumatic

320.2000T 14" x 35" x 35"1/8"Honda GX160 Gas, 5.5 HP 8" 130

TFP 200 Gas

TFP 200 Cutters IndividualCutter

N/A

320.5120

320.3658

320.5500

320.5600

320.5650

320.5500

DrumAssembly

320.9620

320.1020SB

320.1020SS

320.1020ST

320.1020SM

320.1020SM

320.002G

Wire Brushes

Beam Cutters

Star Cutters

Tungsten Carbide Tipped Cutters

Milling Cutters (22mm)

Milling Cutters (11mm)

Tungsten Carbide Tipped Cutters(for grooving)

Cutter Applications:

Wire Brushes are ideal for finishcleaning and polishing on steel; canbe used for light concrete deposit.

Beam Cutters are ideal for lightpaint/corrosion removal, withminimal damage to substrate.

Star Cutters are ideal for theremoval of mastics and rubberizedcoatings.

Tungsten Carbide Tipped Cutters are ideal for aggressiveapplications such as roughing concrete and heavy corrosion removal,as well as grooving roadways for non-slip surface.

Milling Cutters are ideal for the removal of plastic road markingswithout penetrating the surface.

TFP 200Electric

TFP 200Pneumatic

TFP 200Gas


Star Cutter Beam Cutter 3M™ Rotopeen™ 'C' FlapP/N 312.S200 P/N 312.R200 P/N 312.MRPC

CS Unitec’s Trelawny™ Rotopeen™ hand-held scarifiersare the ideal alternative to small-area shot blasting forcleaning and preparing concrete and steel surfaces.

• Pneumatic and electric models

• Integrated dust shroud for dust and debriscollection, as well as cleaner, safer removalof lead-based paints and contaminatedparticles

Peening preparation – ideal alternativeto small-area shot blasting

Pneumatic Hand-Held Scarifiers

194.0205

194.C205

194.0405

194.C405

30

30

30

30

2700

2700

2700

2700

3.5

6.0

3.1

4.6

ModelNumber

CFM @90 PSI

Speed(RPM)

2"

2"

4"

4"

CuttingWidth

'C' Flaps

Star Cutters

'C' Flaps

Star Cutters

These models are compatiblewith Star Cutters, Beam Cutters

and Rotopeen™ 'C' Flaps

CuttingMedia

7.5

11.5

9

13.25

Weight(lbs.)

VibrationLevels m/s2

Electric Hand-Held Scarifiers

195.1217

195.1220

110V

220V

2000

2000

3.6

3.6

ModelNumber Motor Power

Speed(RPM)

2"

2"

CuttingWidth

'C' Flaps

'C' Flaps

CuttingMedia

10

10

Weight(lbs.)

VibrationLevels m/s2

Hand-Held Scarifier Accessories

HEAVYSCALING

LIGHTBURNISHING

Applications include:• Aggressive removal of alkyds, adhesives,

lead-based paints, mastics, coatingscorrosion and more

• Cleaning and preparing concrete andsteel surfaces

Nuclear

Ships decks

Construction

Factory Floors

Swimming Pools

Bridge Maintenance

Pipeline Maintenance

––––

Non-slip coatings

Plaster removal

––––

Adhesive removal

Sealant removal

––––

––––

––––

Ceiling / wall paint removal

Floor marking removal

Adhesive removal

––––

––––

Radioactive waste removal/capture

General paint removal

Ceiling / wall paint removal

Floor marking removal

––––

Paint / sealant removal

Protective coating removal

Aggressive removalof thick coatings

Removal of hard coatings, lessaggressive than star cutter

Removal of light paint and rust to bare metal finish

Star CutterCuttingWidth

2"4"

QuantityRequired

80160

Beam CutterCuttingWidth

2"4"

QuantityRequired

56112

Rotopeen™'C' Flap

CuttingWidth

2"4"

QuantityRequired

612

Electric Model 195.1220 2" cutting width with Rotopeen™ 'C' flaps

Pneumatic Models 194.0405 and194.C405, 4" cutting width

Hand-Held Scarifiers - Pneumatic and Electric



VL223

VL203

CS Unitec’s Trelawny™ line of Low-Vibration needle/chiselscalers offer high performance and low vibration forgreater productivity and improved operator comfort.Ergonomically designed with low maintenance and quickchange tooling option.

CS Unitec’s Trelawny™ Vibro-Lo™ line of Needle/ChiselScalers operate with 7x lessvibration than standard models.These tools utilize vibrationdamping components to offsetthe hammer vibration createdwhen the needles/chisels impactthe workpiece.

• Integrated Vibro-Lo™ vibration reduction technology

• Lightweight, easy to handle

• Optional dust shroud for dust and debris collection

• Tool-free needle changeover

• Converts to chisel scaler in seconds

High power with low vibration –equipped with Vibro-Lo™

Applications include:• Texturing concrete• Cleaning and stress-relieving

weld seams and joints• Removing coatings, corrosion

and other accumulated materials• Splitting, chipping, pointing and brick raking

VL303

Low-Vibration Needle/Chisel Scalers Vibro-Lo™Vibration Reduction

Technology

Needle Scalers andChisel Scalers convert inseconds with optional

head or when purchasedas a Kit. See following

page for Kit information.

10

Low-Vibration Needle/Chisel Scalers

Chisel for light surface marking

Flat for light treatmentand polishing effect

Pointed for veryhard scale

Copper Berylliumfor use in potentiallyexplosive areas

Stainless Steel for usein applications wherecorrosion or humidity is aproblem, such as thefood processing industry

See page 13 for thefollowing types ofneedles:

Chisels for Vibro-Lo™ Chisel Scalers

Dust Collection Shroud for Vibro-Lo™ Needle Scalers

Shank Length Width Application

Pistol

VL223 Needle Scaler

VL223 Needle Scalerwith dust shroud

Chisel Part Number

Square

SquareCranked End

Square

Square

Square

7"

7"

7"

7"

10"

2"

3/8"

3/4"

2-1/2"

3/4"

Spark-resistant Aluminum Bronzefor use in hazardousareas

Weld flux and thick coating removal

Weld splatter removal

Wide flat chisel forthe removal of rustor peeling paint

Flat chisel for weldsplatter and sand cast cleaning

704.3110

704.3205

704.3101

704.3103

704.3107

DescriptionGripModel

Number

Needle Quantity/Diameter

Weight(lbs.)

Blows per

minuteCFM @90 PSI

Noise Leveldb(A)

VibrationLevelsm/s2

Optional Dust Shroud for Needle Scalers – for use with dust extraction vacuums.

Model VL223 Needle Scaler – Order Dust Shroud P/N 418.2003



VL223 Kit – Order P/N 199.2113VL203 Kit – Order P/N 199.2105VL303 Kit – Order P/N 199.3103

CS Unitec offers Vibro-Lo™ Needle/Chisel Scaler Kits, each supplied with the Needle Scaler, 3mm needles, a chisel holder, anvil and a 3/4" blade chisel.

Vibro-Lo™ Needle Scalers

Vibro-Lo™ Chisel ScalersVibro-Lo™ Needle/Chisel Scaler Kits

CS Unitec offers a drop protection kit for our Vibro-Lo™ Needle/ Chisel Scalers. Protect your investment when working at heights or in applications where dropping/losing the tool is likely, including: offshore platforms and rigs, bridges/ scaffolding, vessels and ships.

For VL223 and VL203Order P/N 720.2003*

For VL303Order P/N 720.3003** Safety clip and line not supplied

Drop Protection Kit

Inline

Pistol

VL223 Chisel Scaler

VL203 Chisel Scaler

VL303 Chisel Scaler

199.2213

199.2203

199.3203

6.5

7

9.5

2400

2400

3000

4

4

5.5

76.3

76.3

78.2

3.69

3.33

3.7


NumberWeight(lbs.)

Blows per

minuteCFM @90 PSI

Noise Leveldb(A)

VibrationLevelsm/s2

Inline

H

H

199.2103

139.2103

199.2003

199.2303

199.3003

199.3005

19 / 3mm

19 / 3mm

19 / 3mm

19 / 3mm

28 / 3mm

28 / 3mm

5.25

5.25

6

6

7.75

7.75

2400

2400

2400

2400

3000

3000

4

4

4

4

5.5

5.5

90.7

90.7

90.7

90.7

109.5

109.5

2.56

2.56

2.75

2.75

2.3

2.3

VL203 Needle Scaler


VL303 Needle Scaler


CS Unitecoffers a fullline of non-sparking,non-magneticchisels andsafety handtools forhazardousareas and Exzones.Contact usfor details.


Technology



Standard Needle/Chisel Scalers

• 1-800-700-5919 • Visit our Web site at www.csunitec.com12

Chisel for light surface marking

Flat for light treatmentand polishing effect

Pointed for veryhard scale

Copper Berylliumfor use in potentiallyexplosive areas

Stainless Steel for usein applications wherecorrosion or humidity is a problem, such as the food processing industry

See page 13 forneedles:

Chisels for Standard Chisel Scalers1/2" Square Connection

Shank Length Width Application

Pistol

SemiPistol

1B Needle Scaler1B Chisel Scaler


Square

SquareCranked End

Square

Square

Square

Square

Square

7"

7"

7"

7"

10"

8"

7"

2"

3/8"

3/4"

2-1/2"

3/4"

1/4"

Moil Point

Spark-resistant Aluminum Bronzefor use in hazardous areas

Weld flux and thick coating removal

Weld splatter removal

Wide flat chisel for the removalof rust or peeling paint

Flat chisel for weld splatterand sand cast cleaning

Mortar removal for repointingbrick work

Concrete chipping

704.1110

704.2105

704.1101

704.1103

704.1107

704.1106

704.1112


NumberNeedle

Qty./Dia.Weight(lbs.)

Blows per

minuteCFM @90 PSI

Noise Leveldb(A)

VibrationLevelsm/s2

Dust Collection Shroud for Standard Needle ScalersOptional Dust Shroud for Needle Scalers – for use with dust extraction vacuums.Model 2B and 2BPG Needle Scalers – Order Dust Shroud P/N 418.2199Model 3BPG Needle Scaler – Order Dust Shroud P/N 418.3039

* 3BPG Chisel Scaler 135.3395 has 5/8" hexagonal chisel holder and is compatible with chisels shown on page 14. All others Chisel Scalers shown above have 1/2" square connection.

Standard Needle and Chisel Scalers

TVS™ Needle Scalers with Integrated Vacuum Shroud

Inline

H

H

12 / 3mmN/A

19 / 3mmN/A

3.53.3

5.754.4

38003800

30003000

3.03.0

5.55.5

110.498.9

113.398.6

8.58.2

9.317.4

123.2199125.2300

133.3199135.3300135.3395

19 / 3mmN/A

28 / 3mmN/AN/A

5.754.5

8.256.26.2

30003000

220022002200

5.55.5

8.08.08.0

113.398.6

114.5105.1105.1

12.622.4

18.925.625.6

131.3099134.3200

141.4099144.4200

28 / 3mmN/A

35 / 4mmN/A

107.5

12.58.2

22002200

18001800

8.08.0

8.58.5

114.5105.1

117.4105.1

2BPG Needle Scaler2BPG Chisel Scaler

3BPG Needle Scaler3BPG Chisel Scaler3BPG Chisel Scaler*



Pistol

2B Needle Scaler


NumberWeight(lbs.)

Blows per

minuteCFM @90 PSI

Noise Leveldb(A)

VibrationLevelsm/s2

Inline 139.2007 6.4 3000 5.5 98.6 17.4

139.2107

139.3107

6.6

9.9

3000

2200

5.5

8.0

98.6

105.1

22.4

19.9

2BPG Needle Scaler

3BPG Needle Scaler

CS Unitec's Trelawny™ TVS™ Needle Scalers with Integrated VacuumShroud enable dust-free working in hazardous applications when usedwith a dust extraction vacuum (see page 15 for dust collection systems).

Pistol Grip

Semi PistolGrip

Above: Model 1B Chisel Scalerwith Square Cranked End Chisel

for removal of flux

CS Unitec offers afull line of non-sparking, non-magnetic chiselsand safety handtools for hazardousareas and Exzones. Contact usfor details.

Standard Needle Scalers and ChiselScalers convert in seconds with optional

head or when purchased as a Kit.Contact us for more information.

111.1099114.1200

121.2099124.2200

Inline Grip

12.219.9

23.545.2

Chisel Part No.

Available in 3mm flat tip only; for use in potentiallyhazardous areas.

Needles

Flat Tip

2mm

2mm

2mm

2mm

2mm

3mm

3mm

3mm

3mm

3mm

3mm

4mm

4mm

4mm

4mm

3mm

3mm

6 x sets of 29 needles



Box of 100 needles

Box of 2000 needles





Box of 100 needles

Box of 1000 needles (180mm long)



Box of 50 needles

Box of 500 needles

Box of 1000 needles 5" long (127mm)

19 x needles 5" long (127mm)

412.1129

412.1151

412.1165

452.1110

442.1107

413.1112

413.1119

413.1128

413.1149

453.1110

443.1107

414.1119

414.1135

454.1105

444.1107

443.1105

443.1115

Flat-tipped needles will reduce markingon metal surfaces and can give apolishing effect. For use on thin gaugemetals and any surface where a lighttreatment is required.2mm needles used on a welded joint produce a similareffect to shot peening, reducing stress in the weld.

Size Description Part #

Chisel Tip

3mm

3mm

3mm

3mm

3mm

3mmConversions:2mm = 0.08"

3mm = 0.12"

4mm = 0.16"

180mm = 7"





Box of 100 needles

Box of 1000 needles

413.2112

413.2119

413.2128

413.2149

453.2110

443.2107

These needles will clean the samematerials as a pointed tip, but will leavelight surface marking


CS Unitec’s Trelawny™ needles last 10x longer than standardneedles. Save time and money with fewer needle changes and less downtime.

All of CS Unitec’s Needle Scalers are delivered from stock completewith 180mm long x 3mm diameter chisel-tipped high-performanceneedles. Other needle holders are available as accessories for usewith 2mm and 4mm diameter needles. We also offer spark-resistantneedles for use in potentially hazardous areas and Ex zones, as well as stainless steel needles for usein humid areas – such as applications in the food processing industry – where corrosion is a concern.

Standard pack set is one carton of 6 sets. Some models are packed as an individual set in a box. Boxes of 100 qty. needles in a durable, reusable plastic container are available, as well as larger quantities.

Pointed Tip

3mm

3mm

3mm

3mm

3mm

3mm

4mm

4mm

4mm

4mm





Box of 100 needles

Box of 1000 needles



Box of 50 needles

Box of 500 needles

413.3112

413.3119

413.3128

413.3149

453.3110

443.3107

414.3119

414.3135

454.3105

444.3107

Sharpened to a conical point, these arethe most effective in breaking throughvery hard scale on materials where somesurface indentation is permissible – or where a roughening or keying of the surface is actually desirable.


3mm

3mm

3mm

3mm

3mm

3mm

Box of 12 needles

Box of 19 needles

Box of 28 needles

Box of 49 needles

Box of 100 needles

Box of 500 needles

403.1312

403.1319

403.1328

403.1349

453.1310

443.1307


Spark-Resistant Copper BerylliumH

Available in 3mm flat tip form only, to be used inapplications such as refurbishment of food processingmachinery or areas of high humidity where the corrosiveeffect on needles would be prohibitive.Used on decorative concrete surfaces where contamination of thesurface from carbon steel needle is undesirable.

3mm

3mm

Box of 100 needles

Box of 500 needles

453.1207443.1207


Stainless Steel

• 1-800-700-5919 • Visit our Web site at www.csunitec.com

See page 15 fordust extraction

systems.

13

Long-Reach Chisels/Scrapers/Scalers


2ft. Chisel4ft. Needle4ft. Chisel5ft. Chisel

4ft. Chisel5ft. Chisel6ft. Chisel

136.3299137.3400136.3499136.3599

136.3497136.3597136.3697

8111112

6.757.58.5

2200220022002200

220022002200

ModelNo.

Weight(lbs.)

4.54.54.54.5

4.54.54.5

841048486

898984

CFM@ 90PSI

Blows per

minute

Noise Leveldb(A)

Chisel Accessories

Needle Scaler Accessories

Scraper Accessories

• Ice• Residue• Adhesive• Asbestos• Linoleum• Carpeting• Plaster

• Mortar• Floor tiles• Metal slag• Rubber coatings• Roofing materials• Chemical spillages• Bituminous products

Applications include removal of:

CS Unitec’s Trelawny™ Long-Reach Scrapersfeature one tool with multiple applications.

• Available in 2', 4', 5' and 6' lengths• Three tools in one – chipper, scraper and descaler• Quick-change chisel release• Low air consumption• Standard and "LITE" models

Chip, scrape and descalewith one versatile tool

Chipping Scraping Descaling

705.1100

705.1101

705.1102

705.1106

705.1112

705.2102

708.1101

9"

9"

8"

9"

8"

8"

1"

2"

1"

4"

2"

4"

4"

1-1/8" comb insert

Spark-resistant aluminum bronzefor use in hazardous areas

Flat chisel for sand cast chipping

Asphalt cutter / paint removal /general chipping applications

Removal of linoleum from floor base

Spark resistant aluminum bronzefor use in hazardous areas

Floor tile removal

Brick cleaning and reclamation (usewith 8" long comb holder 708.1100)

ChiselPart No.

ChiselLength

Blade Width Applications

H

H

All long-reach scrapers are available as needlescalers by changing the scraper/chisel with theneedle attachment P/N 415.3532. See page 13for needles.

Flat

431.3504

431.3508

431.3512

Beveled

431.3904

431.3908

431.3912

439.3504(5 Blades)

439.3508(5 Blades)

439.3512(4 Blades)

439.3524(5 Blades)

439.3528(5 Blades)

439.3522(4 Blades)

Adhesive andpaint build up

removal

Paint andcoatingspillageremoval

Carpet andtile removal

Stubbornadhesiveremoval

Carpet andtile removal

Adhesiveremoval

4"

8"

12"

4"

8"

12"

ScraperAssemblyPart No.

BladePack

BladeWidth

Applications

14

Long-Reach Chisels/Scrapers

StandardScalers

Model Description

LITEScalers

Model CS 1445 H(shown at left)

automatically"pulse" cleansfilters withoutinterruptingoperation!

• Vibration reduction technology• Remove paint, epoxy, glue and other hard coatings• Smooth rough surfaces• Clean concrete before applying new paint or coatings• Collect dust for clean working area with a CS Unitec dust extraction vacuum


Low-Vibration Hand-Held and Walk-Behind Grinders

Model No.

10,000

10,000

9,500

10

12

18

5"

5"

7"

14

16

20

EBS 125.5 DEBS 1802 DEBS 180 H

MotorPower (Amps)

GrindingCapacity

LoadSpeed (RPM)

Weight(lbs.)

5" dia. EBS 125.5 D 7" dia. EBS 180 H5" dia. Heavy-duty EBS 1802 D

1,380 849" 20 EBS 235

Hand-held Grinders

Optional Walk-behind Carts:for EBS 125.5 - P/N 37210for EBS 180 H - P/N 37217

Diamond Grinding WheelsUncoated PCD Grinding

General Use (clear) Concrete Wheelfor EBS 125.5 37114 37102 37115for EBS 1802 D 37114 37102 37115for EBS 180 H 37111 37112 37119

Diamond Plate/Inserts for EBS 2359" Base Plate - P/N 37120 EDiamond Inserts (Gold) - P/N 37122 (5 pieces per set)Diamond Inserts (Yellow) - P/N 37123 (5 pieces per set)PCD Diamond Inserts (Black) - P/N 37121 (5 pieces per set)

Optional Filter BagsPaper filter bags for CS 1225 and CS 1445 - P/N 416014 (5-pack)Plastic filter bags for CS 1225, CS 1445 and CS 1500 - P/N 421742 (5-pack)Paper filter bags for CS 1500 - P/N 416021 (5-pack)Slurry filter bags for CS 1500 - P/N 420592 (3-pack)

9" dia.EBS 235

Walk-behind Grinders

7" EBS 180 Hwith Walk-Behind Cart

CS 1225 H

CS Unitec’s dust extraction vacuums offer strong 130 CFM air flow and an electromagnetic pulse filter cleaning system to maximize vacuum power and dust collection.

• Ideal for use with power tools

• 99.999% HEPA filtration efficiency of particlesdown to 0.3 microns; automatic filter cleaning

• "Power Take Off" outlet activates the vacuum ON/OFF from the power tool switch

• Non-HEPA models available, 99.930% filtration efficiency

• Kit available to connect two power tools (P/N 198804)

Dust Collection Vacuums with HEPA Filtration

"PowerTake Off"

outlet

HEPA Vacuum Specifications

CS 1225 H CS 1500 H

Power 11 Amp 11 Amp 11 Amp

Air flow 130 CFM 130 CFM 130 CFM

Tank capacity 6.6 gal. 13 gal. 9 gal.

Weight 24.3 lbs. 35.2 lbs. 24.3 lbs.

Filter P/N (2pk.) 428956 428956 428956

CS 1445 H

Standard Vacuum Specifications

CS 1225 CS 1500

Power 11 Amp 11 Amp 11 Amp

Air flow 130 CFM 130 CFM 130 CFM

Tank capacity 6.6 gal. 13 gal. 9 gal.

Weight 24.3 lbs. 35.2 lbs. 24.3 lbs.

Filter P/N (2pk.) 416069 416069 416069

CS 1445

15

We make no claim that use of a vacuum will eliminate contaminants. Wear an approved respirator mask and follow all appropriate OSHA safety regulations forproper ventilation, dust handling, eye protection, etc. when using a dust extraction grinder and vacuum.

Concrete Grinders and Dust Collection Vacuums


3-speedEBM 350/3 P (motor only, foruse with compatible stands)EBM 350/3 PSA (anchor stand)EBM 350/3 PSV (anchorvacuum stand)

Drill holes up to 14"

END 130/3POSV

Wet/Dry - 2-speedETN 2001 PETN 2001 PSAETN 2001 PSVDrill holes up to 4"

END 712 PEND 1550 PETN 2001 PETN 162/3 PEND 130/3 POEBM 350/3 PDBE 160

Model No.

• Drill holes from 5/32" to 18" dia. in floors, walls and ceilings• Fast drilling of reinforced concrete, concrete, brick, block and stone • 5/8" and 1-1/4" standard thread connections• Drills are equipped with a "slip clutch"• Wet/Dry models have dust collection port

Wet and Dry Diamond Core Bits available for concrete, stone, asphalt andmore. Contact us for details.

0-8000

1800-4400

0-800/0-1570

0-510/0-1150/0-2500

600/1300/2800

230/500/1030

700

5

7

15

15

16

28

34**

5/32" to 3/4"

1/4" to 2-5/8"

up to 4"

up to 6"

up to 6"

up to 14"

up to 6"

6.3

13

15

19

15

24.5

18

MotorPower (Amps)

Drilling Diameter

Load Speed (RPM)

Weight(lbs.)*

Drill with Anchor Stand

Model No.

Drill with AnchorStand & VacuumPump Model No.

Wet

Hand-Held and Rig-Mounted Core Drills

Wet and Dry Diamond Core Drills - Electric

Wet - 3-speedEND 130/3 POEND 130/3 POSAEND 130/3 POSVDrill holes up to 6"

N/AN/A

ETN 2001 PSAETN 162/3 PSA

END 130/3 POSAEBM 350/3 PSA

Included

N/AN/A

ETN 2001 PSVETN 162/3 PSV

END 130/3 POSVEBM 350/3 PSV

N/A

* Weight is for hand-held models only. Please contact CS Unitec for weight information on drill rig combinations.** Weight is for the complete drill rig.

END 712 PMini Diamond Drill for tile,natural stone and concrete

Drill holes 5/32” to 3/4"0-8000 RPM

1-speedDBE 160Rig-mounted

Drill holes up to 6"

Note: Hand-held core drills are intended up to a max. of 3" dia. for hand-held drilling or up to 6" dia. with a stand.

Wet/Dry - 3-speedETN 162/3 PETN 162/3 PSAETN 162/3 PSVDrill holes up to 6"

END 1550 PIdeal for stone, tiles,ceramic, porcelain,stoneware, glass, reinforced concrete and more

Drill holes up to 2-5/8"1800-4400 RPM

Swivel anchor stand available: BST 50V

Wet


EHD 1300 EHD 2000Drill holesup to 5"

Drill holesup to 3-1/4"

PowerWater CapacityPump OutputWater LiftWater PressureAir FlowCanister VolumeCanisterDimensionsWeightSlurry Filter Bags

17 Amp, 115 VAC/60Hz

7 gallons

78 GPM at ground level

18 ft. max. discharge height

14.5 PSI (pump delivery)

150 CFM

13 gallons

Stainless steel tank with cart

20.5" W x 21.6" L x 39.5" H

59 lbs.

P/N 420592

CS 2000

Water Recycling and Slurry Containment Vacuum

• Ideal for wet-working tools such as diamondcore drills, tile saws and wet grinders

• Slurry and debris are contained in filter bag

• Continuous loop system returns clean waterback into the vacuum for delivery back tothe tool

• Can also be used as a regular wet/dryvacuum and to pump water from onelocation to another

Hand-Held Dry Core Drilling

EHD 1300EHD 2000

12

15

up to 3-1/4"

up to 5"

0-2000

0-1000/0-2000

7

13

Model No.

MotorPower (Amps)

Drilling Diameter

Load Speed (RPM)

Weight(lbs.)

Water Collection Rings

Part No. Description35875 Water Collection Trap Ring for BST 104/60 V3587A Water Collection Trap Ring for BST 162 V35879 Water Collection Trap Ring for BST 300 and BST 300 V35849 Water Collection for Hand-Held Drilling (ETN 2001 P)35847 Water Collection for Hand-Held Drilling (END 130/3PO and ETN 162/3P)255.036 Water Collection for Hand-Held Drilling (2 1320, 2 1333, 2 1335 and 2 1317)

CS 2000 shown with END 130/3POSV Core Drill and WaterCollection Ring.

Dry Diamond Core Drills and Stands

BST 104/60VAnchor VacuumStand, 30" high,

21 lbs.

BST 300 VAnchor VacuumStand, 44" high,

50 lbs.

BST 162 VAnchor VacuumStand, 38" high,

31 lbs.

BST 300Anchor Stand,

44" high,45 lbs.

BST 85Anchor Stand,

31" high,16 lbs.

Core Drill Stands

360˚ swivelrange

BST 50VAnchor Stand,

17" high,16 lbs.

Model2 1327 0010 SA

2 1333 00102 1333 0010 SA2 1333 0010 SV2 1335 0010 2 1335 0010 SA2 1335 0010 SV2 1328 0050 SA2 1328 0050 SV

Model No.

77

77

77

123

123

123

123

123

3"

6"

6"

3"

6"

6"

12"

12"

2.1

2.1

2.1

3.8

3.8

3.8

3.8

3.8

MotorPower (HP)

Max.Drilling

Dia.CFM@90 PSI

18

49

51

21

52

54

66

72

Weight(lbs.) Stand

N/A

Anchor Stand

Anchor Stand & Vacuum Pump

N/A

Anchor Stand


Anchor Stand


Note: Hand-held core drills are intended up to a max. of 3" dia. for hand-held drilling or up to 6" dia. with a stand.

400/900/1600

400/900/1600

400/900/1600

300/700/1350

300/700/1350

300/700/1350

300/700/1350

300/700/1350


Model 2 1317 0030

• Rugged 3-speed gearbox with mechanical slip clutch

• Ideal for heavy-duty wet drilling in concrete, reinforced concrete and asphalt

• Self-regulating oil flow control – required volume of 6 GPM; flow up to 13 GPM is automatically bypassed back to the tank

• Hose diameter: 1/2" ID Hose with 3/8" FF (HTMA) Couplings

Wet Diamond Core Drills - Hydraulic and Air

Hydraulic Core Drills

Model 2 1328 0050 SA

Model 2 1333 0010

Pneumatic Core Drills

Power Packs

• Ideal for use with ourhydraulic power tools

• Delivers 5 GPM or 8 GPM at 2000 PSI

• Easy to move with liftand latch handle

• Weighs 330 lbs.

• Removes moisture and dirt from airlines; a float valve automatically ejectswater and dirt

• Includes automatic oiler; protects toolsfrom freezing in cold environments

• Eliminates air motor downtime causedby water and dirt

• Connections for two tools, max. airflow 185 CFM

AirPac Dryer/CleanerModel CSAP-2

Model P95Hydraulic Power Unit

2 1317 0030*

2 1327 0010 SA

2 1327 0010 SV

Model No.1-1/4"x7 UNC Male5/8"x11 UNC Male

G 1/2" Female

1-1/4"x7 UNC MaleG 1/2" Female

Optional: 5/8"x11

1-1/4"x7 UNC MaleG 1/2" Female

Optional: 5/8"x11

6 GPM

6 GPM

6 GPM

6"

12"

12"

3.6

4.2

4.2

MotorPower (HP)

Max.Drilling

Dia.

FreeSpeed (RPM)

ConnectingThreads

Oil Flow/2000 PSI

16

69

82

Weight(lbs.) Stand

N/A*

Anchor Stand

Anchor Standand Vacuum

Pump

Note: Hand-held core drills are intended up to a max. of 3" dia. for hand-held drilling or up to 6" dia. with a stand.* For Drill Rig with Anchor Stand, Order No. 2 1317 0030 SA; for Drill Rig with Anchor Stand and Vacuum Pump, Order No. 2 1317 0030 SV

380/900/1800

380/900/1800

380/900/1800

Load Speed (RPM)

• Rugged 3-speed gearbox with mechanical slip clutch

• Ideal for heavy-duty wet drilling in concrete, reinforced concrete and asphalt

• Pneumatic power for hazardous areas and Ex zones

Air Tool LubricantProLube-ATL - P/N CS 7043-001 (gallon)

Air Tool Lubricant with Anti-FreezeProLube-ATL/AF - P/N CS 7049-001 (gallon)

Air Tool Line Conditioner/CleanerFor use in underwater air tools – displacesmoisture and inhibits rust and corrosion ofair motors - P/N MS 9105 (quart)


Rotary Hammer Drills

2 1266 0010*2 2404 00102 2404 0030*2 2417 0010*

1" dia.

3" dia.

3" dia.

6" dia.

0-950

0-625

0-625

0-250

0-2000

0-3000

0-3000

0-2500

Blows/Minute(BPM)

DrillSpeed(RPM)

Core BitCapacity

(Concrete)

3/8" dia.3/4" dia.3/4" dia.

11/4" dia.

TwistDrill

(Wood)

0.75

0.7

0.7

1.6

21

21

21

53

MotorPower(HP)

CFM @90 PSI

7

11

11

26

Weight

1/2" Chuck

SDS Plus

SDS Plus

SDS Max

ToolSystem

12x 81/2 x 4

16x 81/2 x 4

16x 81/2 x 4

191/2 x9.8x41/2

Dimensions(inches)

* Underwater model – Optional underwater air tool line conditioner to displace moisture, Part No. MS 9105.

1/2" dia.

1" dia.

1" dia.

2" dia.

Solid BitCapacity

(Concrete)

Air Model 2 2404 0010SDS Plus up to 1" dia.

Large Masonry BitsSDS Max up to 2" dia.

Small Masonry BitsSDS Plus up to 1" dia.

Hydraulic Model2 2406 0010 SDS Plus

SDSDrillBits

SDS Plus – Hammer and Drill1" bit capacity for drilling concrete and masonry

HydraulicModel

2 2418 0010SDS Max

Hammer with RotationIdeal for concrete drilling

Rotation OnlyFor drilling steeland wood (not reversible)

Drill concrete anchor holes, thru holes,piping and mechanical openings for

construction and repair work. Switches torotary drilling mode for steel and wood.

Air Model 2 2417 0010SDS Max

Second handleposition

SAE #8 port forhydraulic hoseconnection

SAE #8oil port

ATEXATEX

• SDS chuck• Safety clutch protects against overloading and jamming• Hammer drill holes in concrete, brick and masonry• Rotary drilling mode for straight drilling of steel and wood• Open center hydraulic standard, closed center optional

Pneumatic and hydraulic: powerful percussiondrilling for concrete and masonry

PneumaticHammer Drill

Model No.

2 2406 00102 2406 0020 Same as above. Includes 2 2406 9970 Pressure Reducing Valve for 2000 PSI.2 2418 00102 2418 0020 Same as above. Includes 2 2406 9970 Pressure Reducing Valve for 2000 PSI.

3" dia.

6" dia.

0-625

0-250

0-3400

0-2500

Blows/Minute(BPM)

DrillSpeed(RPM)

Core BitCapacity

(Concrete)

3/4" dia.

11/4" dia.

TwistDrill

(Wood)

0.8 HP

1.8 HP

5.8-13.2

2.6-13.2

Power@ 1160

PSI

FlowRange @1160 PSI

(GPM)

15

37

Weight

SDS Plus

SDS Max

ToolSystem

18x 101/4 x 4

191/2 x111/8 x71/2

Dimensions(inches)

Hydraulic Hammer Drills operate at hydraulic pressures of 1160 PSI max. Pressure Reducing Valves are available to reduce pressure from 2000 PSI or5000 PSI. See above. Available with optional closed center.

1" dia.

2" dia.

Solid BitCapacity

(Concrete)

HydraulicHammer Drill

Model No.

Hydraulic Pressure Reducing ValvesPRV Part No. 2 2406 9970 reduces output pressureof standard hydraulic power units from 2000 PSI(140 bar) to 1160 PSI (80 bar). Included with SDS Plus Hydraulic Hammer Drill 2 2406 0020 and SDS Max Hydraulic Hammer Drill 2 2418 0020.

Pressure Reducing Valve Part No. 2 2406 9900 reduces theoutput pressure of larger-output hydraulic units (i.e. backhoes,large earth tractors, excavators, service trucks, etc.) from max.5075 PSI (350 bar) to 1160 PSI (80 bar) working pressure.Optional accessory – Part No. 38632

Closed Center FlowControl Valve

SDS Max – Modes of Operation2" bit capacity for drilling concrete and masonry


Mixing Machines

Professional, Heavy-duty, Hand-held Mixers for Fast, Efficient Mixing

Mixing Station for Medium- to High-viscosity Batches

Model No.

0-450

250-580

0-450

100-275

9

11.5

15

15

9.5

10.5

10.5

14.5

EHR 18 S

EHR 20.1 R

EZR 22 R/RLTwin Paddle

EHR 23/1.3R

MotorPower (Amps)

LoadSpeed (RPM)

2 bags/20 gal.

3 bags/25 gal.

5 bags/25 gal.

5 bags/35 gal.

CapacityWeight(lbs.)

SuitablePaddles

WG 120MG 120RG 120

WG 135MG 140

TWP 140

P/N31610000(included)

WG 160MG 160

TWP 160

700lbs./hr.

900lbs./hr.

1200lbs./hr.

1800lbs./hr.

Max.Output

From self-leveling compounds to prefab mortar, CS Unitec has aportable mixer to do the job quickly. Every CS Unitec mixer hasbeen designed for high reliability, with the power to provideoptimum blending of construction materials on the job site.

Heavy-duty Galvanized Steel Mixing PaddlesHelical design mixes from the bottom up, eliminating air pockets

Portable Mixing Stands - Save time by running mixers independently

RG 1204.5" dia.

WG 1204.5" dia.

WG 1355.4" dia.

WG 1606.25" dia.

Low Viscosity Medium Viscosity

MG 1204.5" dia.MG 1405.6" dia.MG 1606.25" dia.MG 2359.25" dia.

High Viscosity Fold & Stir

MH 240 9.625" x 6.25"Ideal for decorativeconcrete coatings

Model 25GP-WD Model RST 91 Model RST 10

CS Unitec offersthree air-poweredmodels that areinherently saferfor mixing paint,glue, epoxy, mortar,concrete, refractory cementand other materials in shipyards andthe oil and gas industries. They can beused around water with no fear ofshock or blown circuitry. Contact us for details.

Pneumatic-poweredMixers for HazardousEnvironments

EZR 22 R/RLPush-pull Mixer: Quick,

thorough mixing with twinpaddles and clockwise/

counterclockwise rotation

EHR 18 S SetIncludesWG 120paddle

EHR 20.1 RSetIncludesMG 140paddle

EHR23/1.3 R

SetIncludes

MG 160paddle

Ideal for mixing medium- to high-viscositymaterials, including filler and levelingcompounds, tile cement, ready-mixedmortar, plaster, screed and more.Reliable, high-power motor mixesbatches up to 24 gallons in heavy-dutybucket. Integrated safety switch disablesmotor if frame is lifted during mixing.

Automix 90Capacity: 3 bags, 24 gal.Output: up to 900 lbs./hourPower: 14 Amp / 110 Volt ACFree Speed: 115 RPMLoad Speed: 50 RPMWeight: 77 lbs.Stirring Rod: No. 31460000 (included)

TWP 1405.5" dia.

TWP 1606.375" dia.

Overlayments &Colored Products

• 14mm threadconnection

• 24" paddle length

Mixing paddleswith 1/2" hexshank availablefor standard drill chucks


Portable Mixing Station

Multiple Batch Mixing with Removable LinerMixing multiple batches is easier and faster with the new, removable liner and rimless bucket system.

• Mix consecutive batches without downtime• Resilient, pliable liner is easily cleaned• Alternating liners prevents cross contamination• Extends life of bucket

Bowl Capacity:6 x 50 lbs. mix+water (23 gal /350 lbs.)5 x 22 kg mix+water (86 liters/160 kg)

Tilting Cradle:Balanced for easy operation

The PORTAMIX HIPPO features:• Easy operation – one person can mix, transport

and pour 6 bags or 23 gallons• Accurately place material directly onto the floor• Produces excellent mix consistency• Ideal for mixing and dispensing into 5 gallon containers• Pre-tinted material is easily blended• Dust extraction port for vacuum connection

After mixing the first batch, the liner can be removed andcleaned. To speed up production, a second liner can beused while the first liner is being cleaned. The use of a lineralso helps to prevent cross contamination and minimizeswear to the HIPPO bucket, extending its life.

PMH 80F-RL Level Floors w/ Rimless Bucket and Removable Liner

PMH 80X-RLRough Terrain w/ Rimless Bucket and Removable Liner

Power

2-Speeds

Bucket Capacity

Weight

15 AMP / 110 V*

140 & 470 RPM

23 Gallons

109 lbs.

Specifications

PORTAMIX MEGA HIPPO® Models

* 220 Volt available

Control dust with HEPA

vacuum system CS 1445 H

Mix, Transport and Pour Directly Onto the Floor!

PORTAMIX PMH 80F-RLWith Rimless Bucket and

Removable Liner4 Casters for Level Floor Use

Allows accurate placement – pour andspread at the same time.

PORTAMIX PMH 80X-RLWith Rimless Bucket and

Removable Liner2 Tires for Rough Terrain Use

Increased height – pour directly intobuckets or carts.

Two Models Available:

The HIPPO is also availablewith a Pneumatic-poweredMixing Motor

PMH 80F-AIR; PMH 80X-AIR:

2.2 HP, 90 PSI/67 CFM, 2speeds (190/420 RPM)

TW225 – for half batches (2-3 bags); 9" diameter x 27" long; ideal for plasters,concrete, mortars, resins and tile adhesives. 8" long helix and side bars.

TW225D – for full batches (5-6 bags); 9" diameter x 27" long; ideal for self-levelingcompounds, screeds, paints, plasters and epoxy. 15" long helix andside bars.

The 9" wide helix and side bars lift and shear the product quickly and efficiently toproduce an excellent mix consistency and thorough mixing of colors and additives.The paddle's large 9" diameter provides increased peripheral speed which eliminatesthe need for high-RPM mixing and helps to prevent flash curing.

TW225

TW225D

8"

9"

15"

9"

The PORTAMIX MEGA HIPPO® is supplied with two mixing paddles:


PowerBlade DiameterMax. Depth of CutLoad SpeedNo-load SpeedWeightBlade

20 AMP / 110 V

7"

21/3"

4,300 RPM

7,500 RPM

17 lbs.

P/N 37443000

PowerBlade DiameterLoad SpeedNo-load SpeedArbor SizeMax. Slot WidthMax. Cutting DepthWeightBlade, Standard, 6"Blade, Premium, 6"

20 AMP / 110 V

6"

4,300 RPM

7,500 RPM

7/8"

113/16" (46mm)

13/4" (45mm)

12.8 lbs.

P/N 37440

P/N 37441

Model EMF 150

Wet / Dry 7" Electric Circular Saw

Walk-behind Cut-off Saw – 20" Capacity

CSH 100CSH 125CSH 150

5 HP

9.5 HP

9.5 HP

Power

5250

3200

3200

RPM(No Load)

Max.Depthof Cut

4"

5"

7"

90

92

92

Direct

Gearbox

Gearbox

CFM @100 PSI

14

14

18

Max.Blade

Capacity

22

26

28

DriveWeight(lbs.)Model No.

Pneumatic Concrete Saws – Hand-held and Walk-behindCut concrete, asphalt, masonry and more

• Wet or dry cutting of concrete, reinforced concrete,asphalt, masonry, steel and more

• Cut up to 7" deep with no gas or engine fumes

• Low maintenance – no belts,pistons, fuel lines or carburetors

• Adjustable blade guard with built-in water connection

• In-line oiler for motor lubrication

• 1" arbor size for diamond blades

• 1/2" NPT air connection

• Cut up to 7" deep with no gas or engine fumes

• Low maintenance – nobelts, pistons, fuel lines orcarburetors

• Designed for tough cuttingjobs, including jointsawing, floor sawing,trenching, road repair andplant maintenance

• 9.5 HP pneumatic motorwith gearbox drive

• Wet and dry cutting of stone and masonry materials,including granite, marble, terrazzo and concrete

• Adjustable cutting depth up to 2-1/3" for precise cuts

• Ideal for landscapers, renovators and stone shops

• Vacuum connection for use with CS Unitec's dustextraction vacuum systems

• Cut channels in concrete andmasonry, adjustable sizes

• Cut two parallel grooves up to113/16" wide x 13/4" deep

• Operates with two parallel blades and spacers

• Works 5/8" from the edge or corner

Wall Slotter

CSR 150 9.5 HP 2900 7" 92 Gearbox20 107

Hand-held Cut-Off Saw

CSR 150

Model EDS 181

Hand-held Cut-off Saws, 14" and 18"

Concrete Saws

Premium Diamond BladesWet/Dry, for Cured Concrete

Part No. Description734 906 12" x .125 x 1"734 908 14" x .125 x 1"734 916 16" x .125 x 1"734 909 18" x .125 x 1"734 910 20" x .125 x 1"RES.403 14" x .125 x 1" (rescue)

Walk-behind Cut-Off Saw


Diamond Concrete Chain Saws, Pneumatic and Hydraulic

CS 536163-1

CS 536163-2

CS 536163-3

CS 566110-1

CS 566110-2

CS 566110-3

6.5

6.5

6.5

11

11

11

Power(HP)

124 CFM @ 90 PSI (6 bar)

124 CFM @ 90 PSI (6 bar)

124 CFM @ 90 PSI (6 bar)

8 GPM @ 2500 PSI (172 bar)

8 GPM @ 2500 PSI (172 bar)

8 GPM @ 2500 PSI (172 bar)

32

33

34

28

29

30

104

104

104

95

95

95

88 dB

88 dB

88 dB

88 dB

88 dB

88 dB

Motor Specifications

5700

5700

5700

5700

5700

5700

No LoadSpeed(RPM)

Weight w/Bar andChain

No LoadTorque(in.-lbs.)

NoiseLevelat 3 ft.

10"

15"

20"

10"

15"

20"

Max.Depthof CutModel No.

Pneumatic Concrete Chain Saw

Hydraulic Concrete Chain Saw

CS 536163-PG2*

CS 536163-PG3**6.5

6.5

Power(HP)

124 CFM

124 CFM

32 lbs.

33 lbs.

104

104

88 dB

88 dB

CFM@90 PSI

5700

5700

No LoadSpeed(RPM)

Weight w/Bar andChain

No LoadTorque(in.-lbs.)

NoiseLevelat 3 ft.

15"

20"

Max.Depthof CutModel No.

PowerGrit Diamond Air Saw for Ductile IronThe PowerGrit system allows the user to perform the entire cut from oneposition – a feature especially helpful in reducing the amount of excavationrequired in underground cuts.

6’

5’

2.5’

4.6’

• Specifically designed for the demanding requirements ofprofessional sawing and drilling contractors

• Deep plunge cuts – up to 20" deep

• Square corners up to 19" with no overcuts

• Cut mechanical openings andirregular shapes

* For 15" PowerGrit Saw and Pipe Clamp – order no. CS 536163-PG2C** For 20" PowerGrit Saw and Pipe Clamp – order no. CS 536163-PG3C

Concrete Saws

Air Powered

Air

Old

New

15" PowerGrit Chain P/N PG 52-3810

20" PowerGrit Chain P/N PG 53-5080

PowerGrit Pipe Clamp P/N PG 56-9960(12" cap.; includes mounting axle)

Optimized for air and hydraulic chainsawing -cut concrete with steel reinforcement

AirFORCE F4™

Diamond ChainsAirFORCE Premium Chains

10" – Part No. CC 01-254015" – Part No. CC 01-381020" – Part No. CC 05-5080

Guide Bars with Internal Water Feed10" Guide Bar, for 25 segment Diamond Chain - P/N GB 01-254015" Guide Bar, for 29 segment Diamond Chain - P/N GB 03-381020" Guide Bar, for 34 segment Diamond Chain - P/N GB 05-5080

PowerGrit Chains and Clamp

CS UNITEC, Inc.22 Harbor Avenue, Norwalk, CT 06850Phone 800-700-5919 • 203-853-9522 • Fax 203-853-9921Email [email protected] • www.csunitec.com

ALL SPECIFICATIONS ARE SUBJECT TO CHANGE © Copyright 2014, CS Unitec, Inc., 10-14-7.5M

Diamond Saw

View product demonstrationsat www.csunitec.com.

5" Diamond Saw for hard tile and natural stone materials• Wet and dry cutting of tile, natural stone and stoneware

• Stepless mitre adjustments up to 45˚ – no tools required

• Roller guide smoothly guides saw and protects surface

• Adjustable cutting depth up to 13/8"

• Integrated water supply with flow regulator easily adjustswater volume for dust-free working while wet cutting

• Vacuum connection for use with CS Unitec's dust extractionvacuum systems

PowerBlade DiameterMax. Depth of CutNo-load SpeedArbor SizeWeight

11.4 AMP / 110 V5"

13/8"12,500 RPM

7/8"6.4 lbs.

Model EDS 125

Model EDS 125for wet/dry cutting

Stepless mitre adjustments up to 45˚ – without tools

Integrated watersupply with flowregulator

Dust collection portfor use with dustextraction systems

Cutting Tables for use with the EDS 125

Easily transportable

• Rust-proof, lightweight and easily transportable to the job site

• Precise cutting of tiles up to 3/4" thick with EDS 125 saw

• Adjustable angle stop for miter cuts up to 45˚

Max. CuttingLength

Model: ETT 700 ETT 1200

Quickly attach EDS 125to the table without tools

Optional cutting table –ETT 700 and ETT 1200 (see below)

28"

32 lbs.

47"

39.7 lbs.

Optional blades:P/N 3744C, 5" Diamond blade for 1/4" milling, wet/dryP/N 3744A, 4-1/2" Diamond blade for cutting curves, wet/dry

5" Diamond Blade included (P/N 3744B)

for wet/dry cutting

Weight

Documents

Concrete and Masonry Tools - CS Unitec€¦ · Rotary Hammer Drills (Air • Hydraulic) p. 19 Powerful percussion for drilling concrete and masonry. SDS Plus and SDS Max chucks. Hammer