kkConcrete 70

Compression testing machines, 4 columns standard and high stability frame

4 columns types, standard kN 1200 1500 2000 3000 3000 5000

Manual operated, 1 manometer C011 C036 C051 C066 C080Manual operated, 2 manometers C012 C037 C052 C067 C081Motorized, 1 manometer C013 C038 C053 C068 C082 C086Motorized, 2 manometers C014 C039 C054 C069 C083 C086-01Motorized, Cybertronic unit C109 C015 C040 C055 C070 C084 C086-02Motorized, Servotronic unit C104 C016 C041 C056 C071 C085 C086-03

4 columns, high stability frameMotorized, 1 manometer C089 C089-06 C089-15Motorized, 2 manometers C089-01 C089-07 C089-16Motorized, Cybertronic unit C109 C089-02 C089-08 C089-17/C087 C088Motorized, Servotronic unit C104 C089-04 C089-10 C089-19/C087-1 C088-01

C011, C036, C051, C060, C066 C014, C039, C054, C063, C083

C015, C040, C055, C064, C070, C084 C089-04, C089-10, C089-19, C087-01 C087, C087-01, C088, C088-01

C013, C038, C053, C068, C082

Concrete 71Compression testing machinesThree basic types are available:Machines with four columns prestressed frame, standards UNI 6686,1,2 -ASTM C39 -BS 1610 NF P18-411 Machines with four columns high stability and stiffness frame, standards EN 12390 -BS 1881 -DIN 51220 Machines with en bloc frame 2000 kN, standards ASTM C39, NF P18-411, DIN 51220 - BS 160, UNI 6686

General descriptionLoad frameThe load frame is extremely strong and oversized to grant high rigidity and stability. The upper head holds the precision lapped ball-seating and the compression platen. They are surface hardened HRC 60 and ground. Design emphasis has been placed on simplicity both of construction and operation so that our machines are rugged, easy to use and maintain and designed for heavy continue use. They are available in 1200 kN, 1500 kN, 2000 kN, 3000 kN, 5000 kN capacity, both hand-operated and motorized, at one or two gauges with electronic digital display measuring system and with automatic servo-controlled console with microprocessor. The different versions give the possibility to test cubes, cylinders, blocks. All the machines can be equipped with safety guards.

Hydraulic systemPiston has large diameter, this allows the hydraulic circuit to work at low pressure with longer life of working components and higher precision in the results. Piston is ground and lapped and a packing high quality set of three elements is utilized. Motorized models have a dial device to visualize, pre-select and control the flow allowing an uniform load rate as requested by standards. A fast approach ram action device is foreseen to avoid dead times during stroke of the ram. The manual pump has two stages for fast approach ram action and automatic change for test pressure. Power pump is multipiston, assuring continuity of delivery. A movement indicator visualizes instant by instant the piston's excursion during the compression test. A hopper is foreseen avoiding the powder of the broken specimen to enter into the cylinder of the press damaging the packing set.

Load measuring systemsGaugeThe gauges are Bourdon tube type with max. load pointer, zero adjustment and mirror face to avoid parallax errors. Low pressure gauge is fully protected from overload by a pressure control device.Digital display units

CYBERTRONIC digital computerized multi-channel display unit C109For acquisition, visualization, processing and saving of the test dates. Permanent fil up to 450 complete sets. Big graphic display , measuring range kN, Kg, lb, t, Mpa, N/mm2, selectable language, RS232 for PC connection, automatic linearity guided algorithm with high precision, class 0.5. Integrated printer available.

SERVOTRNIC Servo-controlled control unit C104for automatic tests throughout all phases: data acquisition, display, processing, pace rate adjustment and software for print out of results and certificate. Including motor, hydraulic unit.

Calibration and precisionAll the compression machines are calibrated with high accuracy electronic instruments and they are guaranteed in grade "A" (max. error less than ±1%). A calibration certificate is supplied along with the machine.

C109

C104

kkCompression testing machines with digital display unit

Load frameThe load frame is extremely strong and oversized to grant high rigidity and stability. The upper head holds the precision lapped ball-seating and the compression platen. They are surface hardened HRC 60 and ground. Design emphasis has been placed on simplicity both of construction and operation so that our machines are rugged, easy to use and maintain and designed for heavy continue use.

Hydraulic systemPiston has large diameter, this allows the hydraulic circuit to work at low pressure with longer life of working components and higher precision in the results. Piston is ground and lapped and a packing high quality set of three elements is utilized. Motorized models have a dial device to visualize, pre-select and control the flow allowing a uniform load rate as requested by standards. A fast approach ram action device is foreseen to avoid dead times during stroke of the ram. A movement indicator visualizes instant by instant the piston's excursion during the compression test.

Load measuring systemsC109 CYBERTRONIC digital computerized display unit For acquisition, visualization, processing and saving of the test dates. Permanent file up to 450 complete sets. Big graphic display , measuring range kN, Kg, lb, t, Mpa, N/mm2, selectable language, RS232 for PC connection, automatic linearity guided algorithm with high precision, class 0.5. Integrated printer available.

C104 SERVOTRONIC Servo-controlled display unitfor automatic tests throughout all phases: data acquisition, display, processing, pace rate adjustment and software for print out of results and certificate. Including motor, hydraulic unit.

Software UTM2 for Cybertronic unit C109 for managing and remote control of press from PCC109-10 Software, licence for compression testsC109-11 Software, licence for flexion testsC109-12 Software, licence for tensile splitting testsC123 Software Servonet for Servotronic display unit,

licence for compression and flexionC125 Software for secant compression elastic modulus on

conrete ISO 6784, DIN 1048

C127 Graphic printer on thermo paper on board

Compression testing machine with Cybertronic display unit C109

Compression testing machine with Servotronic display unit C109

Four columns frame, standard, kN 1200 1500 2000 3000 3000 5000Motorized, Cybertronic C099 C015 C040 C055 C070 C084 C086-02Motorized, Servotronic C104 C016 C041 C056 C071 C085 C086-03Four columns frame, superiorMotorized, Cybertronic C099 C089-02 C089-08 C089-17/C087 C088Motorized, Servotronic C104 089-04 C089-10 C089-19 C087-01 C088-01

Concrete 72

Digital display units for compression testing machinesC109 Cybertronic digital computerised three-channel unit for acquisition, visualisation, processing and saving of the tests datas.Big permanent file for up to 450 complete test sets, graphic display of 240x128p pixels with high resolution, test software for current standards, selectable measuring range kN, Kg, lb, t, Mpa, N/mm2, psi, lb/in2, kg/cm2, pace rate display in M’a/s, psi/s, kN/s, kg/cm2/s, kg/cm2/s, lb/s, kg/s, t/s. RS232 port for PC/printer connection, selectable languages, simplified functions for calibration by PC keyboard, automatic linearity guided algorithm with very high precision, class 0.5 staring from 10% of the maximum value. C127 On board graphic printer for thermo papier

C104 Servotronic servo-controlled unitFor managing and remote control of the test from PC. Provides fully automatic tests throughout all phases : data acquisition, display, processing, pace rate adjustment and software for the print out of results and certificates.Rapid approaching, touching on and breaking of the specimen under direct pump control, tare, checking of pace rate by device that can be pid programmed on the step actuator, continous load display, breaking load detection, elaboration of specific resistance value, graphic elaboration directly on the display. The Servotronic comprises motor, hydraulic unit, multi-channel computerised digital device C109.

Software for Cybertronic unitC109-10 Software for the managing and remote control from a

PC including license for compression test.C109-11 Software for the managing and remote control from a

PC including license for flexure test C109-12 Software for the managing and remote control from a

PC including license for tensile splitting test.C123 Software for SERVTRONIC unit for the managing

and remote control. For compression and flexure tests on concrete and mortar.

C127 Graphic printer on board for thermo paperC128 Table printer, size A4H009-01 PC , 17" display, including installation of software

C104

C109

Concrete 73

Main Features of the UTM 2 1. Automatic identification of the appliance connected. 2. Setting of the sequence of operations concerning the test to be

made, settable by the operator and realisation of a personalised testing profile.

3. Memorisation of the test in the database with the possibility to process it again.

4. By means of a PC connected by a serial port RS232 to the appli-ance foreseen (see list of application machines and fields) it allows interacting, test processing, graph and test report constructing and many other possibilities of remote control of the machine.

5. It allows visualising the instant loads, the instant deformations, the load/deformation/stroke graph, the remote control of the main functions of the machine. It can visualise the eventual alarms and/or errors, calculate and save all the parameters of the test made with the possibility to process again. It can manage the test files.

6. By means of an easy menu (Windows) the user can create or personalise test profiles following his own needs: he can set the dates of the test, the analogical measuring channels features and the setting of a test cycle personalising the speed charts.

7. The test dates can be commented by means of test titles to be reported on the certificate or on the graph desired.

8. The user can select the calculation algorithms and, using them, the software will process all the results required by the Standards

9. The colours and the graph scales of the activated windows can be freely selected by the user.

10. The test certificate can be personalised with the fol l o w i n g va r i a b l e s : nam e of the com p a n y , ki n d of tes t, da t e , ki n d of gr a p h an d num b e r of pa g e s .

11. Possibility to have a remote control of the machine calibration.

Concrete 74

Flexural testing machinesThree basic design are available

C090 Series to perform flexural tests on concrete beam specimens having max. dimensions of 150x150x750 mm conforming to the specifications EN 12390/5 -UNI 6133 -ASTM C78,C293, AASHTO T97 -BS 1881:118 -UNI 6133 -UNE 83305 NF P18-407.

C091 Series with open sided frame to perform flexural tests on concrete beam specimens having max. dimensions of 200x200x800 mm and to perform tests on: flat blocks (max. width 500 mm) conforming to the BS 6073/1, flagstones and kerbs conforming to the BS 7263, kerbs conforming to the NF P98-302. Any type of beam having max. size 550xh250 mm (lower roller max. length 1325 mm)

C093 Series to perform flexural tests on concrete beam specimens having max. dimensions 200x200x800 mm and to perform tests on any kind of other product with max. dimensions 550xh550 mm (adjustable distance between lower rollers up to max. 1325 mm).

All series are proposed in the models hand operated, motor operated, Digitronic, Cybertronic and Servotronic digital display unit . It is also possible, by using suitable accessories, to perform the following tests:-Compression test on portions of 40x40x160 mm mortar prisms broken in flexure conforming to EN 196, DIN 1164 (compression devices mod. E170, E170-01).-Compression tests on 50 mm mortar cubes conforming to ASTM C109 (Compression device mod. E171)-Compression tests on 70 mm mortar cubes conforming to BS 4550 (Compression device mod. E171-01)-Splitting tensile test on cylindrical specimens Ø100,150,160 mm conforming to EN 12390/6 -NF P18-408 -BS 1881:117, ASTM C496 -UNI 6135 (Device mod. C100)-Splitting tensile test on concrete cubes and concrete block pavers conforming to EN 12390/6,1338 (Device mod.C103)

C090-01

C090-03

C091-02+C109C093-02+C104

Concrete 75Universal groupsFor compression test on concrete specimens, blocks, flexural test on concrete beams, compression tests on mortar specimens, slitting cylinder tests.

The composition of the universal group are formed by: C092 Flexural frame 150 kN capacityWith dial gauge (see mod.C090-01 for technical specifications), fitted with a three-way hydraulic valve, used in connection with an existing compression testing machine (see mod.C013-C089-16) dial gauge reading, motorized. With pipes, connectors and accessories.

C092-01 Flexural frame 150 kN capacitySame as C092 but with pressure transducer and electronic digital display unit with microprocessor (see mod.C090-02 and C099), fitted with a three-way hydraulic valve, used in conjunction with an existing electronic digital display compression machine (see mod.C015-C089-17).

C092-02 Flexural frame 150 kN capacitySame as C092-01 but with automatic servo-controlled console and microprocessor (see mod.C090-03 and C098), used in conjunction with an existing automatic servo-controlled compression machine (see mod. C016C089-19).

Compression frames on concrete specimens and blocksThe composition of this group is obtained by:C092-05 Compression frame on mortar specimens250 kN or 500 kN capacity with pressure transducer (see mod. E159 and C099) fitted with a 3-way hydraulic valve used in conjunction with an electronic digital display concrete compression machine (see mod.C015-C089-17), with pipes and connectors.

C092-07 Compression frame on mortar specimensSame as C092-05 but used in conjunction with an automatic servo-controlled concrete compression machine (see C016-C089-19).

These groups offer the advantage to carry out compression tests on concrete cube, cylinder and block specimens and compression tests on mortar specimens. An hydraulic 3-way valve activates alternatively the concrete compression frame or the mortar compression frame by utilizing only one hydraulic pumping unit. The group is combined according to the specific requirements (technical and economic) of the customer by choosing the concrete compression frame among the different available models (mod. C015-C089-19) with max. capacity of 1200 kN to 5000 kN.

In addition to the proposed groups, it is possible to compose many other alternative testing groups with digital display measuring system (mod.C099) or with automatic servo-controlled "Servo-unit " system (mod.C098).

Our technical department is at your disposal to solve any specific demand.

C053 C092

C055 C092-01

C092-02+C104+C092-02

Concrete 76C 100 Splitting tensile test device for cylindrical specimens∅ 150x300 mm, 160x320 mm, 6x12”. Standards ASTM C496 -NF P18-408 -EN 12390/6 UNI 6135 -BS 1881:117. To perform the test, these devices have to be used with a concrete compression machine having of a low capacity measuring range.

C101 Splitting tensile test deviceSame as mod.C100 but to perform tests on cylindrical specimens ∅ 100x200 mm, 110x220 mm, (4x8"), weight 15 kg. C101-01 Splitting tensile test deviceFor cylindrical specimens from ∅ 100x200 mm (4x8") to 160x320 mm (6x12"). The base is equipped with flat springs centering and keeping in position the specimen. Two columns with adjustable height sustain the upper plate by two springs. This item is an alternative solution to mod. C100 and C101. Weight 26 kg.C102 Splitting tensile test deviceTo perform tests on cylindrical specimens ∅ 40x80 mm, 1 kg.C103 Splitting tensile test device Standards EN 12390/6, 1338To perform tests on concrete cube specimens 100 and 150 mm and on concrete block pavers. Weight 26 kg.C100-01 Packing strips, hard board made, dimensions 4x10x350 mm to be used for splitting tensile tests with mod. C100,C101, C101-01. Pack of 100.C106 Flexural deviceFor two point and center point tests on concrete beams 100x100x400 (500) and 150x150x600 (750) mm with two lower rollers, one of them articulated and two upper rollers for third point tests. It is possible to place in the center only one upper roller for center point tests.C107 Autocentering deviceFor cubes 100 and 150 mm side to be used with compression machine having platen ∅ 216 mm (1500 and 2000 kN).

Compressometer, static modulus of elasticityStandards ASTM C469 - UNI 6556To determine the strain and deformation characteristics of concrete specimens. It comprises two steel rings for clamping to the specimen, two gauge length bars, dial gauge division 0.001 mm and spherically-seated lever unit.C130 Compressometer for cylinders ∅ 150x300, 160x 320 mm and

6x12 ". Dial reading 0.001 mm.C131 Compressometer for cylinders ∅ 100x200, 110x220 mm and 4x8

". Dial reading 0.001 mm. C132 Compressometer for cubes 150x150 mm side., dial reading 0.001

mm.

C100 C101 C102

C101-01

C103

C106

C107

C132

C130

Concrete 77The load cells are suitable for the calibration of compression testing machines. They consist of a high quality steel block, named sensitive element, where some strains have been fitted. The whole is housed in a sheathing. While the load is applied, strains are transmitted to an amplifier (mod. C139), which gives a load digital reading. With calibration certificate.

C138 Electronic universal tester for load cellsThis unit for professional uses, is proposed as an alternative to mod. C139, and is recommended to Metrologic Laboratories, SIT centers etc. It has to be used with the "High performance strain load cells" mod. C142 to C142-07. The input section is realized with a chain of an analogue circuit, a frequency generator to supply the electric load cells an AID converter with resolution ±200’000, divisions. With serial output RS 232C and 24 columns printer output, 220/240 V, 50/60 Hz, dimensions 125x210x204 mm, 3 kg.

C138-01 Software "Matcal"For data acquisition and processing of calibration values with certificate printing. With CD ROM

C154-01Positioning device for footmeter test

C155 Digital measuring tester with microprocessorThis unit reads simultaneously the four values supplied by the electric strain load cell. The values are memorized, automatically elaborated, visualized and printed (by optional printer). in carrying case, 220/240 V, 50 Hz, dimensions 450x350x160 mm, weight 8 kg.

Standard load cells C140 – C140-09 kNSteel cylinder with four balanced strain gauge bridges and a fifth strain gauge for load measurement calibration test. Complete with connectors, cables, calibration certificate.Models Capacity Dimensions

kN ∅ x height mmC140 25 82x59C140-01 50 82x59 C140-02 75 82x59C140-03 100 82x59C140-04 300 135x200C140-05 600 135x200C140-06 1000 135x200C140-07 2000 135x200C140-08 3000 135x200C140-09 5000 180x200

C142-06C155

C154-01High performance load cells C142 – C142-07Standards EN 10002/3 class I - ASTM E74, class ATechnical specifications: full scale nominal output 2 mV/V hysteresis (non linearity) ±0,1%, repeatability 0.03%, nominal voltage excitation DC 12, uncertainity 0.05%.Models Capacity Dimensions

kN ∅ x height mmC142 30 100x127C142-01 100 105x164C142-02 300 140x160C142-03 600 140x170C142-04 1000 150x180C142-05 2000 135x200C142-06 3000 135x200C142-07 5000 158x258

C140

C140-02

C138-01

C154-01

C138C140-07

Concrete 78

C160 Drum type mixer, 140 l capacitySuitable for field mixes of medium strength concrete. Drum volume 140 liters, yield 90 liters of concrete. 220/240 V, 50 Hz, 0.3 Hp, dimensions 720x1320x1280 mm, weight 84 kg.

C161 Drum type mixer, 100 l capacitySame as model C160 but having drum volume 100 liters, yield 65 liters of concrete, weight 60 kg.

C162 Pan type mixer, 56 liters capacityThis multiflow mixer absorbs fewer air during mixing, requires shorter mixing time and grants a perfect homogenity in mixtures having a low water cement ratio. The pan is easily removable by means of a trolley (accessory).The blades are hardened against wear. Mixing pan Ø 640x330 mm high, 220/240 V, 50 Hz, 2 Hp, weight 250 kg.

C 162-01 TrolleyFor fast and easy removal of the mixing pan of the multiflow mixer.

C162-02 safety guards to 89/392/CEE directives.

C166 Concrete mixers, pan typeEN 12390-2Used to prepare concrete specimens or mixtures, these pan type mixers ensure a uniform efficient fast mixture action. They are of easy and practical utilisation, suitable for laboratory and field purposes. The mixers are equipped with a manually controlled discharge opening situated on the bottom part of the pan, for direct unloading of the mixture into a suitable container.The mixing lades and paddle can be adjusted in height. They are manufactured of special quality hardened steel to resist wear. The pan and the mixing gears have big thickness ration, the gears are from hardened and rectified steel, the motor reducer is in oil-bath with gleason conical coupling. Controls through magneto-thermo switch and release automatic coil contained in IP67 box.

C166 Pan type mixer, mixing capacity 200 lPan diameter 960 mm, pan volume 350 l, mixing capacity 200 l of concrete, power supply 400 V, 3 ph, 50 Hz, 7.5 Hp, dimensions 1400x100x1500 mm, weight 350 kg

C166-01 Pan type mixer, mixing capacity 110 lPan diameter 800 mm, pan volume 200 l, mixing capacity 110 l of concrete, power supply 400 V, 3 ph, 50 Hz, 4 Hp, dimensions 1200x100x1300 mm, weight 260 kg

C166-02 Pan type mixer capacity 100 lPan diameter 790 mm, pan volume 200 l, mixing capacity 100 l of concrete, with wheels and handling bar, power supply 400 V, 3 ph, 50 Hz, 4 Hp, dimensions 1200x100x1300 mm, weight 260 kg.

C160

C162

C162-01

C166 C166-01

C166-02

Concrete 79Slump cone testStandards EN 1235012 - BS 1881:102 - AASHTO T 119 ASTM C 143 - NF P 18-305, P 18-451 UNI 7163, 9418 - UNE 7103, 83313.For the determination of the consistency, the medium and high workability of fresh concrete.C180 Slump cone complete set including: C180-01 Slump cone only, stainless steel C180-02 Tamping rod, galvanized ∅ 16x600 mm C180-03 Cone funnel, galvanizedC180-04 Base plate for C182 set V176-02 Steel rule 500 mm long V183 Aluminum scoop. Total weight 10 kg.

C181 Slump cone only, galvanized steelV185-03 Scoop, stainless steel for sampling fresh concrete, dimensions ∅ 125x250 mm. Capacity 5 kg.C182 Slump cone setIncluding galvanized slump cone, base plate, tamping rod, aluminum scoop, steel rule 500 mm long.

C183 Vebe's consistometerStandards EN 1235013 - BS 1881:104 - UNI 9419The Vebe consistometer method is based on the same principle of the simple slump cone test method for the determination of the workability of concrete, but it has the advantage of a mechanized action. After removing the slump cone, the concrete undergoes a vibration to determine its slump. A spacer disk set in contact with the upper surface of the wet concrete gives the operator the opportunity to determine when the compaction is complete. 220/240 V, 50 Hz, 250 W, dimensions 26x38x70 cm.

C185 Compacting factor apparatusBS 1881:103 BS 5075To undertake a more precise and sensitive test procedure than the simple slump test. The apparatus consists of two conical hoppers mounted on a cylinder. Each hopper has a hinged flange with quick release mechanism and all is mounted on a rigid steel stand. With tamping rod Ø 16x600 mm long, dimensions 50x40xl5I cm, weight 55kg.

C 186 Kelly ball apparatus, ASTM C360Consisting of a hemispherically ended cylinder with guiding frame and a handle graduated in inch and mm, it is used to determine the workability of fresh concrete. The ball is lowered into the concrete and the penetration measured. Cadmium plated for rust protection, weight 15 kg.

C187 K-slump tester, ASTM C 1362To determine the degree of compaction and the workability of fresh concrete. Used for in-situ measurements or inside test moulds. Test result can be correlated against the slump values, weight 500 g.C188 Walz consistometerStandards EN 12350/4 - DIN 1048 - UNI 9420To measure the consistency of fresh concrete. It consists of a metal box with handles 200x200 mm, height 400 mm, painted for rust protection, weight 6 kg.

C180

C182

C183

V185-03

C186

C185

C187

C188

Concrete 80

C189 Concrete workability meter Standard NFP18-452The concrete workability meter (also known as plastometer) is designed to test concrete for dynamic workability. It is suitable for field and laboratory tests to check:- concrete mix for consistency, especially water content- optimum proportioning of concrete constituents (sand, gravel, water, cement)- possible improvement when adding a plastifier - comparing two concrete types.The unit consists of a prismatic receiver divided into two unequal volumes by a removable partition and an electric vibrator. The fresh concrete is poured into the large volume space, the separating partition is removed and the vibrator starts automatically. The test consists in measuring the time required for the concrete to reach an uniform distribution in the receivers. 220/240 V, 50 Hz, 300 W, dimensions 820x420x410 mm, weight 80 kg.

C190 Plasticity meterUsed for quick and easy measurements of the plasticity of mixtures, especially concrete and so to detect rapidly any excess of water. The measuring system is related to the shear strength applied by a three blade head to the mixture under test. It is possible to measure the plasticity at several different points and directly in the mixture, with multiple checking. Obtained values can be easily compared with the values got by the Abrams slump cone test, dimensions ∅130x180 mm.

C192 Flow tableEN 12350/5 - BS 188 1: 105 - DIN 1048 - UNI 8020The apparatus comprises a galvanized steel conical mould, ∅ 130/200xh200 mm, double wooden flow table with galvanized steel top plane, guide device, wooden tamper, used to determine the workability of concrete. The top table has a square surface of 700x700 mm, hinged on one side. C192-01 Conical mouldGalvanized steel made, ∅ 130/200x200 mm height. C192-02 Wooden tamper

C194 Concrete pocket penetrometerStandards UNI 7123 - ASTM C403 - AASHTOT 197 Used for the evaluation of the initial set of the concrete mortar. The penetration plunger has a tip area of 32 mm2. It is plunged into the mortar to a depth of 25.4 mm indicated on the plunger. The resistance expressed in Kpa and Lbf/sq. inch, is shown on the marked reading scale, dimensions ∅ 25x210 mm, weight 400 g.

C213 Concrete penetrometerStandards ASTM C 403 - AASHTOT 197 - UNI 7123,7927 Used to determine the setting time of the mortar fraction in concrete mixes with slump greater than zero, by testing mortar sieved from mix. The apparatus consist of a spring penetrometer (capacity 100 Kgf, precision 1 Kgf) and six interchangeable stainless steel needle pointers of 16, 32, 65, 160, 32 and 650 mm2. A sliding ring indicates the reached load on the handle of the penetrometer, in case, dimensions 450x160x70 mm, weight 5 kg.

C189

C190

C192

C194

C213

Concrete 81C195 Air entrainment meter 5 liters capacityStandards EN 1235017 - BS 1881:106 - UNI 6395 ASTM C231 - NF P 18-353 - UNE 7141Made of cast aluminium alloy. It records directly the percentage of air enclosed in freshly mixed concrete by operating according to the air pressure principle. It is supplied with pressure gauge tamping rod and hand pump. Air content range 0-8 %, division 0.1%, dimensions Ø 250x700 mm, weight 13 kg.

C195-01 Calibration cylinderTo check and calibrate the air meter model C195.C195-02 Carrying case with handles for C195.

C 196 Air entrainment meter 8 liters capacityStandard DIN 1048It consists of an aluminium vessel with bulk in hand operated pressure pump connected to the measuring gauge showing directly the air content in percentage. Air content range 0-10 % division 0.1% up to 8% and 0.5% over, dimensions Ø 250x450 mm, weight 12 kg.

C197 Air entrainment meter 8 liters capacityStandard DIN 1048Identical to mod. C196 but with built in automatic electric air compressor giving air pressure and keeping it constant all along the test, 220/240 V, 50 Hz, dimensions Ø 250x450 mm, weight 14 kg.C 197-01 Filling hopper for mod. C196 and C197

C199 Unit weight measure, 10 liters capacityStandards EN 12350/6 BS 1881:107 - EN 109713Used to determine the weight per cubic meter of freshly mixed and compacted concrete. Steel protected against corrosion, with inside radius between wall and base of 20 mm, with rim and base, height 320 mm, weight 9 kg.

C200 - C205-01 Unit weight measuresStandards ASTM C29, C 138 - AASHTOT 19 - UNI 6394 UNE 7286 - BS 812,1881 - EN 109713Made of heavy steel sheet protected against corrosion, they are used to determine the weight per cubic meter of freshly mixed and compacted concrete. It is used also for the determination of loose bulk density and voids of aggregates.

Model Capacity Inside ∅ WeightC200 1 108.3 2 kgC201 2 108.3 3 kgC201-01 3 160 3.5 kgC201 5 187.7 4 kgC202-01 7 187.7 5 kgC203 10 265 7 kgC204 14 265 9 kgC204-01 15 265 12 kgC205 28 345.6 14 kg205-01 30 345.6 15 kg

V084 Specific gravity frameFor density of hardened concrete.

C195

C195-01

C196

C200 – C205-01

V084

C199

Concrete 82Concrete flow tablesAASHTOT 120 - ASTM C124 - UNI 8020/A - UNE 7102Used to determine the flow of concrete. The apparatus consists of a flow table, stainless steel flow mould, tamping bar.

C208 Manual flow table according to ASTM, AASHTO, UNEOperated by crack handle. Table Ø 762 mm, weight 100 kg.C209 Motorized flow table according to ASTM, AASHTOWith automatic digital drop counter, table Ø 762 mm, 220/240 V, 50 Hz, 750 W, weight 115 kg.C210 Manual flow table according to UNI 8020Operated by crack handle, table Ø 750 mm, weight 100 kg.C210-01 Motorized flow table according to UNI 8020With automatic digital drop counter. Table Ø 750 mm. 220-240 V, 50 Hz, 750 W, 115 kg. C210-02 Flow mould, cast bronze made to UNI 8020.

C211 Joisel apparatusFrench LCPC method.Ø 140x220 mm high. Used to separate the various elements of the fresh concrete such as cement, sand, aggregates. All made from stainless steel, weight 2 kg.

C215 RAM - Rapid analysis machineStandard BS 1881:128Used for the determination of cement content in fresh concrete, coarse and fine aggregate, fly ash and GGBF slag content can also be determined. Fully automatic procedure with quick and accurate test results (max. errors within 5 kg/m3). The complete test takes approx. 10 minutes. The connection to water net for approx. 80 liters each test is required. The weight of the test sample is 8 kg, supplied complete, 220/240 V, 50 Hz, dim. 780x660x 1500 mm, weight 150 kg.

C220 Water test set for concrete mixing Standards DIN 4030 - EN 206, 1008This kit, utilized to test the water mixing concrete, is composed of different dropping bottles, water-proof color scales, test strips. It is suitable, to carry out more than 50 analysis of e.g. total or momentaneous pH, magnesium, ammonium, chloride, odour, sulphate, lime dissolving CO2, carbonate hardness, total hardness etc, in case. Weight 2 kg.

C208

C211

C215

C220

C209

Concrete 83

Plastic cube and cylindrical mouldsThese one-piece moulds, made of hard plastic, strong, light, undeformable, resistant to vibration shocks and wear do not require mounting and dismounting operations, thus saving time and labour. The specimen is expelled from the mould by compressed air or water. They just require a simple clean and demould oiling before being ready for use again for many times. Nominal moulds dimensions meet to EN 12390/1 standard requirements.

C228 Cylinder mould Ø 150x300 mm, weight 2560 g.C229 Cylinder mould Ø 160x320 mm, weight 2560 g.C232 Cube mould 100 mm side, two gangs, weight 1040 g. C234 Cube mould 150 mm side, standard model, 1300 g.C230 Cube mould 150 mm side with reinforced corners, weight 1500 g.C233 Cube mould 150 mm side, "high density" similar to mod. C230, but made of more dense and compact plastic

material, and therefore more resistant to blows and to abrasion. Weight 2 kg.C230-01 Funnel (filling hopper) for an easier filling of fresh concrete into mod. C230.C230-02 Plastic cover for mod. C230, C233 cube mould, useful for transportation. Pack of 10 pieces.C230-03 Grasping pliers for mod. C230, C233, C234 to get easier the carriage.C230-04 Plastic stopper to plug the hole of the mould. Pack of 10 pieces.

Polystyrene cube mouldsThis cube mould, polystyrene made, is "one way" utilized, only for one single test since it must be broken when the specimen is demoulded. It offers different advantages:- it is provided with a top cover keeping inside heat and humidity constant and acting as a curing room- it protects the specimen as a packing during transport of the same- it is extremely light- any trouble concerning the cleaning demoulding and maintenance of the mould are eliminated.

C231 Polystyrene cube mould, 150 mm side, one gang, pack of 40 pieces.C231-01 Polystyrene cube mould, 200 mm side, one gang, pack of 20 pieces. C231-02 Polystyrene cube mould, 100 mm side, four gang, pack of 52 pieces.

C230-01

C234

C230-03C228

C229

C232

C230-02

C230-04

C231

Concrete 84

Steel cube, cylindrical and beam mouldStandards EN - 1239011 - BS 1881:108,109, 110 - ASTM C 192, C31 - AASHTO T23 - NF P 8 - 400 - DIN 51229 - UNI 6130 - UNE 7240These moulds are extremely sturdy and the inside surfaces are grounted and accurately machined. C247 Cube mould 100 mm side, one compartment, weight 6 kgC247-01 Cube mould 150 mm side, one compartment weight 13 kgC247-02 Cube mould 200 mm side, one compartment weight 25 kgC247-03 Cube mould 300 mm side, one compartment weight 90 kgC248 Cube mould 100 mm side, two compartment weight 11 kgC248-01 Cube mould 150 mm side, two compartment weight 30 kgC248-02 Cube mould 200 mm side, two compartment weight 53 kgC248-03 Cube mould 100 mm side, three compartment weight 17 kgC248-04 Cube mould 140 mm side, three compartment weight 30 kgC249 Cube mould 100 mm side, four compartment weight 20 kgC249-01 Cube mould 150 mm side, four compartment weight 45 kgC254 Beam mould 100x100x400 mm, weight 20 kgC254.01 Beam mould 100x100x500 mm, weight 23 kgC254-02 Beam mould 150x150x600 mm, weight 44 kgC254-03 Beam mould 150x150x750 mm, weight 47 kgC254-04 Beam mould 200x200x800 mm, weight 86 kgC254-05 Beam mould 140x140x560 mm, weight 38 kg

C255 Cast iron 150 mm side cube mould, one gangStandards EN 12390 -1 - BS 1881:108 - DIN 51229 - UNI 6127 Four part design plus base plate, weight 17 kg.C256 Cast iron 150 mm side cube mould, one gang, with certificate of conformity.Four part design plus base plate, this mould has been checked in shape, dimensions and tolerances with SIT (NAMAS or equivalent) certified measuring instruments. Each mould is numbered for identification, weight 17 kg.C230-01 Filling hopper for an easier filling of fresh concrete into the cube moulds.

Steel cylinder moulds with baseModels Dimensions Weight

Øx height kgC258 100x200 mm 8 C180-02 Tamping rod Ø 16x610 mm longC258-01 112.8x220 mm 8 C261 Tamping bar 25 mm2 tamping area, 380 mm longC258-02 150x300 mm 15 C262 Straight edge, 460 mm long.C258-03 6"x12" 15 V178-01 Wire brush used to clean mouldsC258-04 160x320 mm 17 C265 Demoulding oil, can of 30 kgC258-05 250x500 mm 80C258-06 150x150 mm 10

C258-04

C254-04C248

C249-01

C255

C258C258-01

C247-02

Concrete 85Poker vibratorsSuitable for the internal compaction of concrete specimens both in laboratory and in site. The Ø of the needle must not exceed 25% of the smallest dimension of the specimen.

C271 Poker vibrator, portable, petrol operated 0.75 hp, tip Ø 25 x250 mm long, flexible shaft 2 m, frequency 12000 vibrations/ min, dimensions 30x30x40 cm, weight 9 kg.C273 Poker vibrator, portable, electricTip Ø 25x250 mm, flexible shaft 2 m, frequency 12000 vibrations/min, 220/240 V, 50 Hz, 300 W, weight 7 kg.C274 Poker vibrator, portable, 12 V DC battery operated with connector for car lighter, tip Ø 25 mm x 250 mm , flexible shaft 2 m, frequency 12000 vibrations/min, weight 10 kg C275 Poker vibrator, portable, electricTip directly connected to the motor shaft, tip Ø 25x250 mm long, frequency 18 000 vibrations/min, 220/240 V, 50 Hz, weight 4 kg.C276 Poker vibrator pneumatic, to be connected to an air compressor having minimum feeding of 25 liter air/min at 6 atm, tip Ø 25x250 mm, frequency 3000 vibrations/min.

Vibrating tablesStandards EN 12390/1 - BS 1881:108 - UNI 6127For compaction of concrete specimens in laboratory they are manufactured from rugged steel sheet. With motor-vibrator having 3000 vibrations/min. It is possible to vary the vibration intensity by acting on the excentric masses. The height of the table is 410 mm, 220/240 V, 50 Hz. Models Table dimensions Weight kgC278 600x400 mm 60C278-01 800x400 mm 85C278-02 800x800 mm 115C279 1100x550 mm 145C279-02 Separate control panelC279-03 Clamping device to fix the moulds

C280 Vibrating table for plastic mouldsWith On/Off switch, 220/240 V, 50 Hz, 300 W, dimensions 320x320x300 mm, weight 20 kg.

Cylinder capping equipment, sulphur methodThe above mentioned specifications require that the two faces of the concrete core or cylinder specimen must be made perfectly flat and parallel, by using sulphur capping equipment.C290 Capping set for cylinders ∅ 15x30 cm

6x12" including:C290-01 Vertical cylinder capper for 15x30 cmC290-02 Cylinder carrier for 15x30 cmC290-05 Capping compound, pack of 25 kg.C290-03 Electric melting pot 3 liters, 1200 W.V186-01 Stainless steel ladle

C291 Capping set for cylinders ∅ 16x32 cmAll elements also available individually.

C296 Steel capping plate 50x30x2 cm for concrete blocks

C271 C273

C275

C280

C278

C279-03C279-02

C279

Concrete 86

Curing tank for concrete specimensEN 12390/2 - BS 188 1:111 - UNI 6129 - ASTM C3 1, C 192, C51 1 - AASHTO T23, NF P 18 - 404 - UNE 7240

C302 Curing tank, capacity 1000 lMade from heavy stable and robust polyethylene, base rack, cock for an easier water discharge. inside dimensions 104x104x60.5 cm, weight 60 kg. Without thermostat

C304 Curing tank capacity 1000 lMade of zinc coated steel sheet to prevent it from corrosion., inside dimensions 150x75x75 cm. The tank can accommodate up to 64 cubes 150 mm side or up to 48 cubes 200 mm side, 220/240 V, 50/60 Hz, 2000 W, weight 120 kg.

C304-01 With analogical thermostat with heating systemC304-02 With digital thermostat with heating systemC305-01 Plastic cover for C302C306-01 Rack to form the upper shelf for 150 mm cubes, max.

8 racks per tankC306-02 Submersible pump for water circulation, 220-240 V C306-04 Steel cover, zinc coatedC306-05 Analogical thermostat with heating element. It is used

with thermostat in all tank types from 300 to 1000 liters capacity, 220 V, 50/60 Hz, 2000 W.

C307 Accelerated concrete curing tankStandards ASTM C684 - BS 1881This tank has been designed for accelerated concrete strength curing. It comprises a fully insulated double wall tank with cover, inside all of stainless steel, outside from steel painted sheet with an intermediate layer of insulating mineral wool. This tank can hold up to 16 cubes 150 mm side specimens or 16 cylindrical Ø 150 mm specimens or 8 cubes 200 mm side specimens. The test consists essentially in curing the concrete specimens with water heated by 3 electric elements of 1500 W each, temperature range from ambient to 100°C. The separate control panel is provided with a thermo-regulator timer, pilot lights, main switch. Inside dimensions 91x66x68 cm. Overall dimensions 97x72x90 cm, 220/240V, 50/60 Hz, 4500 W, weight 130 kg.

C308 Accelerated concrete curing tank with automatic curing cyclesThe tank is identical to mod. C307, but equipped with digital control panel with microprocessor with following program: heating time, heating temperature, curing time, cooling time, cooling temperature by automatic calling of cold water, ideal for concrete precast industries, cement factories, research laboratories.

C308-01 Strip printerTo record the numeric values of time and temperature on paper with programmable printing time intervals.

C306-02

C306-05

C307

C302+C304-01

C304+C304-02

C304-02

Concrete 87C311 Curing room vaporizerTo humidify curing rooms for concrete and mortar specimen. With humidistat controller, range 30-100% max. room capacity 150 m3, 220 V, 50 Hz, dimensions ∅ 360x230 mm, weight 3.5 kg.

C312 Curing room vaporizerSame to mod. C311, but for rooms up to 500 m3

C312-01 Level regulatorIt allows the direct connection to the water net, for a continuous use of the vaporizers C311 and C312.

C313 Curing room vaporizerFor rooms over 500 m3, capacity 9 l/ h, air circulating capacity 800 m3/h, with humidistat controller, range 30-100%. The unit is directly connected to the water net, 220 V, 50 Hz.

C310 Recording thermometer at six channelsTo measure and record on graphics the temperature inside a concrete mass under relevant curing to know its reactions during the heat of hydration development. The thermometer is suitable to record simultaneously up to six readings in different points or masses, through relevant thermocouples range -10 to +110°C, with 50 meters of thermocouple cable, 4 rolls of graphic paper.

C310-01 50 meters of thermocouple cableC310-02 Roll of graphic paper, pack of 10 piecesC310-03 Writing ink tape, pack of 6 pieces

C314 Climatic chamber, capacity 520 lEN 196 - EN 1367/1 ASTIM C671 - BS 812:124 - CNR no 80 - UNI 8520This thermostatic climatic chamber is designed for all the research and control laboratories where known cold and/or hot temperatures with controlled humidity values are required for any type for freeze/thaw tests, acce-lerated curing tests, hot and cold tests in general. Used also to check the behaviour of aggregates during freeze and thaw cycle tests.Temperature range -20°C +60°C accuracy ±0.5°C, humidity range 10-90%, dew point limits +2°C. Inside and outside frame totally in stainless steel. Digital display of actual and preset temperature, internal venti-lation, forced circulation, inside dimensions 62x63x139 cm, overall dimensions 73x86x209 cm, with 3 adjustable shelves, 220/240 V, 50 Hz, 1000 W, weight 150 kg.

C315 Climatic chamber, capacity 1200 lSame as model C314 but having capacity 1200 1. Double entrance door, inside dimensions 124x73x139 cm, overall dimensions 1460 x 860 x 2090 mm, with 4 adjustable shelves, weight 230 kg.C315-01 Two curves graphic recorderC315-02 Microprocessor temperature programmer

C311 C313

C312C310

C314 – C315

Concrete 88

Core drilling machines "lightweight portable"These drilling machines are extremely practical, lightweight easy to use. The base is from aluminium alloy, the steel column can be angled, the motor support is fixed on rollers and ball bearings. The motor incorporates a water swivel to cool the diamond bit. The machine is supplied complete except diamond bit, expander coupling and spanner which have to be ordered separately.

C318 Core drilling machine with electric motorWith 3 speeds 670, 1140, 1580 rpm, with speed reducer, provided with friction device. The machine accepts bits ∅ 50 to 150 mm, 220/240 V, 50 Hz, 2200 W, dimensions 45x29x86 cm, weight 35 kg. C318-01 Core drilling machine, petrol drivenPetrol engine power 2500 W, speed 390 to 920 rpm. The machine accepts bits ∅ 50 to 200 mm, dimensions 45x29x106 cm, weight 40 kg.

C318-02 Core drilling machine, air drivenAir motor with consumption of 50 liter/air, 3300 W, speeds 250-390-580-830 rpm. The machine accepts bits ∅ 50 to 200 mm, dimensions 52x33x135 cm, weight 68 kg.

C318

C318-01

C318-02

C319 Core drilling machine, petrol drivenIs used for pavement core sampling where it is not easy to get electrical power. Wit vertical screw feed. Drilling excursion 640 mm. Petrol engine 8.5 Hp power, 4-cycle Briggs & Stratton model, dimensions 85x58x123 cm, weight 135 kg.

C319

Concrete 89Core drilling machines "High performance"These drilling machines are extremely robust, compact and reliable. The sliding group is rectified so as to assure a very soft and accurate drilling movement. The drilling excursion is 550 mm and the machine can drill cores up to ∅ 200 mm. The motor is advanced by a rack system with built in water swivel to cool the diamond bit. The robust steel base is equipped with wheels for easy site displacements with 4 leveling and stabilizing feet. All working and moving parts are cadmium plated for rust protection. Diamond bits, expander, coupling and spanner (see accessories) have to be ordered separately.

C321 Universal core drilling machine, petrol drivenCoring angle 0 to 360°, petrol engine, 6 Hp, two speeds 300 and 600 rpm with speed reducer, with friction device dimensions 75x44x30 cm, weight 90 kg.C322 Universal electric core drilling machineCoring angle 0 to 360°C, 3 speeds 670, 1140, 1580 rpm with speed reducer. The height of the vertical column is 100 cm and is pre-built for extension column connection. 220/240 V 50 Hz, 2200 W, dimensions 44x75x130 cm, weight 85 kg.C324 Electric core drilling machine, with vacuum facility Same as C322 but with vacuum attachment suitable under the condition that the surface is sufficiently flat.

C332 Portable electric generator, 4000 W C322-01 Extension column, 1000 mm

Diamond bits and accessoriesDiamond core drill bits are designed for making holes and to get cores from hard materials like concrete, reinforced concrete, rock, stones, bituminous. The diamond utilized for these bits is quality impregnated sinterized type. All bits are 500 mm long. The coupling between the bit and the drilling machine requires a suitable expander coupling. Two basic models are available:- to core concrete, rock, stones, hard materials- to core bituminous materials.

Bits to core Bits to core Outside Inside BitumenConcrete ∅ mm ∅ mm C340-05 C341-05 57 50

C340-06 C341-06 83 75C340-07 C341-07 108 100C340-08 C341-08 160 150C340-09 C341-09 210 200

Expander Core Insidecoupling extractor ∅ mmC343 C346 50C343-01 C346-01 75C343-02 C346-02 100C343-03 C346-03 152C343-04 C346-04 200

C344 Strap wrench useful for unblocking the bitsC345 Extension rod 300 mm for deep holes

C321

C322

C340-05 – C341-09

C343 – C343-04

C345C344

C346 – C346-04

Concrete 90C348 Specimen cutting machineWith sliding support. The machine accepts blades up to ∅ 350 mm, useful cutting height 110 mm. The blade can be oriented for cuts at 45º, dimensions of the sliding table 500x450 m, blade rotation speed 2800 rpm, power supply 220/240 V, 50 Hz, 3 Hp, dimensions 700x1100x680 mm, weight 80 kg.

C350 Specimen cutting machineUsed to cut concrete specimens and any type of construction material like blocks, tiles, pipes, rock cores etc. The machine is equipped with an electro-pump for water cooling pedal guide for vertical cutting safety device against breakage of blade. The machine accept blades up to Ø 450 mm, 400 V 3 phase, 50 Hz,3 Hp, dimensions 1220xx136 mm, weight 125 kg.

C349 Specimen cutting machineBasically same as mod. C350, but it can accept blade having max. ∅ 500 mm, 400 V 3 ph, 50 Hz, 4 Hp.

C350-01 Specimen cutting machineIdentical to mod. C350, but with 220 V, 50 Hz, 3 Hp.

C351 Specimen cutting machine, bench typeThe machine accepts blades up to Ø 355 mm. Shear capacity 120 mm blade rotation speed 3900 rpm, 220 V, 50 Hz 2000 W, dimensions 56x46x39 cm, weight 20 kg.

C350-11 Abrasive blade Ø 400mmC350-12 Diamond blade Ø 450 mmC350-13 Diamond blade Ø 350 mmC350-15 Diamond blade Ø 500 mm

C352 Device for cylinders and coresTo clamp and cut cylinders and cores. The device is fixed to the table of the cutting machines mod. C348, C350, C350-01, C349, weight 10 kg.

C353 Device for irregular shapesTo clamp and to cut irregular shaped specimens, like rocks, stones etc. The device is fixed to the table of the cutting machine model C348, C350, C350-01, C349. weight 5 kg.

C350

C352

C348

C351 C353

Concrete 91Mechanical strain gauges, ASTM C426 - BS 1881:206Used to determine the strain in concrete specimens and structures, rock strata etc. in remote areas and under adverse conditions using a single instrument. It consists of an extensometer with dial analogical gauge, precision 0.001 mm, calibration bar, 50 datum disks, special adhesive, in case.C360 Strain gauge, 100 mm measuring lengthC360-01 Strain gauge, 200 mm measuring length C361 Strain gauge, 300 mm measuring length

Digital strain gaugesIdentical to above but with a digital gauge, battery operated, with reading values 0.001 mm/ 0.0001", battery and RS 232. C363 Strain gauge 300 mm measuring lengthC363-01 Strain gauge 100 mm measuring length C363-02 Strain gauge 200 mm measuring length C362-01 Datum disc, pack of 50 piecesC362-02 Special adhesive tube

Hydraulic shrinkage determination Standards UNI 6555 - ASTM C426This test covers the determination of the hydraulic axial shrinkage of concrete specimens having l00x100x500 mm (or l00x100x400) mm, with aggregates up to ∅ 30 mm. The specimen is prepared with a special mould and after housed in the measuring apparatus that determines the axial shrinkage. The equipment consists of:C365 Shrinkage mould 100x100x500 mmC365-01 Shrinkage mould l00x100x400 mmC366 Measuring apparatus for specimens 100x100x500 mm,

with reference bar and dial gauge, reading 0.01 mm. C366-01 Measuring apparatus for specimens 100x100x400 mm

with reference bar and dial gauge 0.01 mm C366-11 Steel inserts, pack of 10 pieces

C367 Hydraulic shrinkage measuring apparatusFor concrete made over 30 mm size aggregates. The specimen sized 200x200x800 mm is prepared with a standard mould(see C254-04) and measured by the apparatus on six points. With 6 dial gauges, reading 0.01 m and reference bar, weight 35 kg.

C374 Moisture meter “Surveymaster”For measurements in concrete and other materials, both on surface and at depth. Measurement range 0-100 % ±0.1 1%, digital reading, audible alarm, with 2x1.5 V batteries, weight 200 g.C375 Hygrometer for moisture testsThe hammer electrode is inserted into the material to be tested. With hammer probe, cable, casing and a numerical scale for comparative tests, dimensions 200x200x100 mm, weight 2 kg.

C376 Pull-out test apparatusASTM C900 - BS 1881 part 207 - Uni 9535Used to evaluate the concrete resistance as per the strength applied to extract an insert embedded in concrete. Standard equipment comprises hydraulic extraction unit 50 kN with pump, manometer, bearing ring, 10 steel inserts Ø 30 mm, carrying case, weight 18 kg.C376-01 Pull-out inserts Ø 30 mm, pack of 25 pieces.

C361

C363C360

C362-01

C365

C366

C367

C375

C376

C374

Concrete 92

C373 Ultrasonic pulse velocity tester type PalmerGraphic display, measuring range 0-1999.9 μs, amplitude 800 peak volt, extractable memory SDcard, RS232, RS485, 2 probes 55 kHz, 2 cables, 2 outlets for oscilloscope, low battery alarm, ON/OFF switch, calibrating cylinder, grease, with batteries, in carrying case.

C372-01 Ultrasonic pulse velocity instrument TICODisplay unit with nonvolatile memory for up to 250 measured objects, 2 transducers 54 kHz, 2 cables 1.5 m, calibration rod, coupling paste 150 ml, integrated software for transmission to PC, measuring range 15-6553.5 µs, resolution 0.1 µs, voltage 600 V, pulse rate 3/s, battery operated. In carrying case. Weight 3 kg.

C371 OscilloscopeIt visualizes the pulses when passing the material under test offering the advantage to verify on a monitor the correctness of the value in microseconds read on the digital display of the ultrasonic tester, i.e. that no disturbed pulse transmission like reflexion, deviation etc. has altered it, with connections and accessories, dimensions 350x170x420 mm, weight 12 kg.

C371

C372-01

C372

Ø Concrete 93

Rebound concrete test hammersStandards EN 12504/2 - ASTM C805 - UNI 9189 - DIN 1048 - BS 1881: 202 - NF P 18-417 - UNE 83 307 ISO - DIN 8045. Designed for non-destructive tests on concrete structures. It gives an immediate indication of the compressive strength of the concrete using the calibration curve supplied with.

C380 Concrete test hammerClassic model, spring impact energy 0.225 mkg (2.207 joule)suitable for finished concrete structures and buildings having strength resistance from 10 to 70 N/mm2. The hammer has aluminum frame and a very accurate manufacture processing and selected components which ensure high precision test results. Dimensions ∅ 8x34 cm, weight 3 kg.

C381 Concrete test hammerSimilar to C380 but with impact energy of 0.735 joule. Ideal to test small sized, sensitive and thin walled materials, also suitable for rock core samples.

Original "Schmidt" test hammersThe top quality test hammers available on the market with calibration curve chart, abrasive stone, carrying case. C382 Standard model "N" for normal concrete. Impact energy

2.207 joule/0.225 mkgC383 "NR" model, same as C382 model, but having an

automatic incorporated device for recording the impact values on diagram

C383-01 Spare roll recording paper for C383 ( pack of 5 ) C384"L" model similar in shape to the "N" model, but having an impact energy of 0,735 joule and ideal for testing small and impact-sensitive materials. and rock samples. Compressive strength 10-70 N/mm2

C384-01Pendulum hammer PFor compressive strength of 5-25 N/mm2, impact energy 0.883 Nm, readings of measured values on a scale.

C385 Digital concrete test hammer DIGI-SCHMIDT 2000 Impact energy 2.2 Nm, compressive strength 10-70 N/mm2, accuracy ± 0.2R, display unit with non-volatile memory for max. 500o measurement values, display on 128x128 graphic LCD. RS 232 C interface, battery operated, in carrying case weight 3 kg.

C390 Anvil for verification of calibration of concrete test hammers, dimensions ∅ 150x230 mm, weight 16 kg.

All other models of original Schmidt test hammers (LP, LB, PT, M etc.) are available on request.

C380

C382

C383

C385

C390

C384-01

Concrete 94Rebar locatorsFor locating rebars, measuring concrete cover, storing of single cover values and statistical evaluation, determination of rebar diameters. Standards BS 1881: 204 - DIN 1045.

Rebar locator, Profometer 5The lightest instrument in its class. Displays reinforcing bars and concrete covers on a LCD monitor with an X/Y meter scale, even with close rebar interspacing. An user-guiding menu technique and just 9 keys for all function ensure the simplest possible operation. The easily readable display shows up to 240 concrete covers in grey shades. Measures bar Ø to an accuracy of ±1 mm.

C396 Rebar locator Profometer 5SDisplay unit with non-volatile memory for 100’000 measured values that can be spread over 63 objects. Display on 128x128 graphic LCD, interface RS 232. Software for printing statistical values and downloading to PC, battery operated. With universal probe for locating rebars, measuring concrete cover and determining rebar diameters, probe cable 1.5 m, transfer cable 1.5 m. In carrying case. Weight 2 kg.

C397 Rebar locator Profometer 5 ScanlogSame features as model S plus: "CyberScan" function for displaying the reinforcement "Measurement with grid" function for grey-scale display of concrete cover. Probe carriage ScanCar with path measuring device and transfer cable. In carrying case. Weight 2.9 kg.

C400-01 Diameter probe with integrated electronicsC400-02 Dept probe for concrete covers up to 240 mm

C399 Crack detection microscopeTo measure crack width in concrete structures, by operating via an adjustable light source, high definition unit provided by power batteries, carrying case, measuring range 4 mm, division 0.02 mm, magnification 35x, weight 600 g.

C404 Rebar locator CovermeterStandards BS 1881: 2G4 - DIN 1045On-screen menu driven operation, pulse induction technique for stability and performance, automatic zeroing, embedded instrumentation computer, automatic sizing of single bars, steeable low cover audible alarm to enable rapid scanning, large graphic LCD display, measuring range 5 – 150 mm depending on bar size. With batteries, size 220x110x175 mm, 2 kg.

C396

C399

C404

Concrete 95DeflectometersUsed to determine the deflection on bridges, ceilings or any suspended structure, possibility to use the deflecto-meter with pressure or with traction. Reading is direct with a precision of 0.01 mm. One set is composed of articulated support dial gauge reading 0.01 mm with arm, 20 m invar coil, lead, carrying case. C405 One set dial gauge stroke 10 mmC405-01 One set dial gauge stroke 25 mmC406 Three sets, dial gauges stroke 10 mm C407 Three sets 2 dial gauges stroke 10 mm,

one stroke 25 mmC407-01 Three sets, dial gauges stroke 25 mm C407-02 Inextensible invar coil 20 m long

Cracking width gaugesFor monitoring measuring and recording the crack width of a building structure, in vandal resistant polycarbonate, with crack record card each gauge to simplify monitoring, they are suitable for vertical and horizontal movement measurements.C408 Crack width gauge for wallsTo monitor vertical and horizontal movements, also simultaneous, on a plane surface, pack of 5 pieces.C408-01 Crack width gauge for cornersTo monitor comer cracks with two directional and simultaneous movements, pack of 5 pieces.C408-02 Crack width gauge for floors to monitor floor settlements to a wall, column etc., pack of 5 pieces. C408-03 Crack width gauge for difference in levels to monitor the loss of level of any cracked surface, pack of 5 pieces.

C410 Windsor HP probe digital systemStandards ASTM C803 - BS 1881: 207 - ACI 347To evaluate the compressive strength of concrete in place with the penetration method. Non destructive test. It is fast, accurate and simple to perform. The five-minute test does not weaken the structure. Comparison between test results using this method and destructive tests shows a deviation normally situated within 3 % from each other. The method requires a pistol-like device which is loaded with a small explosive charge and metal probe. The charge is precisely measured to give a consistent firing force. By pulling the trigger, the probe is fired into the concrete. Standard equipment consist of driven unit, digital measuring unit with memory for data storage to PC unloading, in carrying case. Probes and power charges are not included and must be ordered separately, dimensions 500x400x200 mm, weight 16 kg.

C410-01 Probe kit silver, colored for natural aggregates with probes and power loads. The kit lasts for 75 tests. C410-02 Probe kit gold colored for lightweight aggregates, with probes and power loads. The kit lasts for 75 tests.

C406

C408 –C408-03

C408

C410

Concrete 96C411 Half-cell corrosion analyzing instrument CANINStandards UNI 9535 - ASTM C876 - BS 1881: 201 For the non-destructive detection of corrosion in reinforce-ment bars of concrete building elements. Display unit with nonvolatile 1 M bit memory for 120’000 measurements, which can be divided into 72 objects. Impedance 10 MΩ, measuring range ± 999 mV, resolution 1 mV, display on 128x128 graphic LCD. Measurement with up to 8 rod or 8 wheel electrodes. Equipped for path measuring, resolution 3 mm, interface RS 232, battery operated. With rod electrode, cable 1.5 m, transfer cable 1.5 m, cable coil 25 m, copper sulphate CuSO4, 250 g. In carrying case. Weight 3.7 kgAccessoriesC411-01 4 bar electrodes system with divisions of 150 mm, for bottom view and vertical operation, with accessories. C411-02 4 wheel electrodes system, for measurement on horizontal surfaces, with accessories.

C412 Half cell digital corrosion meterStandards UNI 9535 - ASTM C876 - BS 1881: 201The digital half-cell enables rapid location of corroding reinforcement without disrupting the concrete cover. The unit is a hand set with an integral (removable) Ag/AgCI/Sat KCI mapping electrode for maintenance free long term stability. The instrument automatically converts and displays the measurements as Cu/Cu S04 equivalent potentials. With battery and low battery indicator. The nylon carrying case contains a 10 m reference lead, sponge head, protective nylon cover and an extension kit with fold-up extension rod to enable remote surveying and fatigue, free testing of bridge, decks etc. Detachable silver/silver chloride mapping electrode. Range/resolution +1999 mV ±1 mV, dimensions 350x300x200 mm, weight 7 kg.

C413 Digital resistivity 2-probe array meterFor assessing the probable rate of corrosion in reinforcing bars with the electric resistivity measurement method. The test is simple to perform and requires only two 6.5 mm Ø holes drilled to a depth of 8 mm. Inject a small amount of conductive gel into each hole and insert the probes. The resistivity is immediately displayed. Low frequency alternating current technique used. 3 digit LCD display. With battery, dimensions 41x 26x14 cm, weight 3 kg.C413-01 Digital resistivity 4-probe Wenner meterSimilar to model C413 except for probe used by surface contact. No hole is required.

C415 Scribe multi role data-loggerA unique multipurpose surveying system for measurements of reinforced concrete structures: half cell potential, concrete resistivity, cover and estimated size of reinforcement, electrical continuity of reinforcement. The multi role data-logger is at the heart of the system for which a number of add-on "heads" have been developed which convert it to an instrument for the measurement and assessment of related characteristics. Select the role required on the data-logger, connect interface and appropriate "head" and start survey.Please ask for detailed leaflet.

C411

C411-01C411-01

C412 C413-01

C413

C415

Concrete 97C414 Resistivity meter RESIFor measuring the electrical resistance of reinforced concrete components for assessing the risk of corrosion.Display unit with non-volatile memory for 7200 measured values, 128x128 graphic LCD, RS232 interface, battery operated. Resistance probe Wenner r with integrated electronics for resistivity measurement by four-point method, rated current 180µA, frequency 72 Hz, impedance 10MΩ, measuring range 0-99 kΩcm, accuracy ± 1 kΩcm. With cable, control plate for resistance probe, in carrying case. Weight 2.5 kg

Pull-off testerLight and precise portable instrument for determining the adhesive force and the tensile strength of concrete, mortar, coatings, paints and lacquers.

C416-01 Pull-of tester DYNA Z16 with pressure gaugetensile force 16 kN, accuracy better than <± 2%, digital display in N/mm2, test disc Ø 50 mm, battery operated, in carrying case. Weight 6 kg

Same model but with 6, 25, 50 or 100 kN available.

C417-01 Pull-of tester DYNA Z16E, electronic typeSame as C416-01 but with pressure sensor, accuracy better than <± 0.5%.tensile force 16 kN. With Dynameter display unit.Same model but with 6, 25, 50 or 100 kN available.

Extraction test DYNAFor measuring the extraction force on anchored bolts and dowels.C418-01 Extraction tester DYNA 16Swith pressure gaugeTensile force 16 kN, accuracy better than <± 2%, digital, tensile bolt, in carrying case. Weight 8 kg

Same model but with 6, 25, 50 or 100 kN available.

C419-01 Extraxtion tester DYNA 16FSEelectronical type, with pressure sensor, accuracy than <± 0.5% on force 0.01 mm on displacement, tensile force 16 kN, indicating unit WIGAmeter for force/displacement, display on 128x128 graphic LCD, RS 232 interface, battery operated, in carrying case. Weight 16 kg

C417-10 Printer DPU 201 GSERechargeable, with mains adapter, battery charger 220 V AC. Weight 0.4 kg

C414

C416-01

C417-01

C418-01

C419-01

6Concrete 98

C436 Permeability test TORRENTAllows the evaluation of the durability of concrete structures especially of high compressive strength concrete.During the measuring procedure, the measuring instrument and the upper concrete layer are placed in a vacuum under a vacuum cell. The pressure increase inside of the chamber cell given by the permeability of the conrete is measured. An important characteristiqc is the outer chamber of the cell. It protects from lateral air streams, which vives an important measuring accuracy.

Basic equipment consists of non-volatile memory for 200 measured objects, display 128x128 LCD, interface 232C, integrated software for printing out, batteries 9V, control unit with membrane pressure regulator and pressure sensor, vacuum connection: small flange 16 KF, carrying case. Total weight 6.3 kg.

AccessoriesC436-01 Wenner probe for the determinati9on of concrete resistance p according to Wenner. The values are stored in the display unit.

Porositester according to Karsten systemFor measuring the water ingress on façade surfacesC437 Vertical porositesterWith plate with vacuum pump for connection 12 V DC, 3 test tubes for vertical surfaces, 2 seals for vacuum plate (reserve) 6 seals for test tubes (reserve). Weight 0.9 kg.

C437-01 Horizontal porositesterWith plate with vacuum pump for connection 12 V DC, 3 test tubes for horizontal surfaces, 2 seals for vacuum plate (reserve) 6 seals for test tubes (reserve). Weight 0.9 kg.

C436

C436-01

Drawing of the air flow to the two chambers of the vacuum cell

C437

Concrete 99C430 Automatic concrete water permeability apparatus with four cellsThis fully automatic apparatus is designed to carry out water permeability tests on cubic concrete specimens max. 150 mm side and cylinder specimens max. Ø 160 mm. The specimens are submitted to hydrostatic stress for a pre-set period. The water filtering through the test specimen is directly collected and measured into a graduated cylinder. It is therefore possible to determine the permeability coefficient in cm/sec. (Darcy coefficient) by the following formula:

cc x hK = ---------

A x t x Pwhere: cc = permeated water in cm3

h = height of the specimen (cm)A = surface area of the specimen (cm2)t = time to permeate (sec.)P = hydrostatic pressure in cm of water column

The equipment consists of a strong metallic frame holding four cells which are hot galvanized for anticorrosion protection. Each cell includes a pressure control manometer. A rechargeable compensation plenum chamber is included as part of the test. The pressure is adjustable from 0 to 30 bar (0-20 bar for model C431) and it is supplied by an automatic pump of variable supply to achieve the most suitable installation for the specimen under test. Water feed is direct from water inlet. Seal pressure obtained through special and practical seal devices which maintain and simplify the use of the machine. It is possible to use one or more cells together. The specimen's sealing system is achieved with a practical and speedy, user-friendly device. Sealing devices are not included in the standard package and must be ordered separately. 220/240 V, 50 Hz, dimensions 250x 50x130 cm, weight 240 kg.

Acessories for model C430 and C431:Sealing device with rubber latex packing, which is between the two hot-galvanized steel collars, with bolts.C432-01 Sealing device for cubes 100 mm sideC432-02 Sealing device for cubes 150 mm side C432-04 Sealing device for cylinders Ø 100 mmC432-05 Sealing device for cylinders Ø 150 mmC432-06 Sealing device for cylinders Ø 160 mmC433 Epoxy resin to isolate the lateral surfaces of the

concrete specimen, can of 5 kg.

C431 Automatic concrete water permeabilitySimilar to model C430, but with two cells, suitable for carrying out tests on concrete cube specimens max. side 200 mm and cylinder specimens max. ∅ 300 mm.

C435 Water impermeability tester for 3 cellsApparatus to determine the depth of penetration of the water into the concrete (impermeability) under known time and pressure. For up to 3 concrete cubic, cylindrical or prismatic specimens having max. dimensions of 20x20x20 cm.V206 Laboratory air compressor.

C430

C432

C431

C435