READY Bender®

Concept Sketches

READY

READY

READY Bender®

CB1 Concept Sketch

A READY Bender® is a CB1 tool when PT, PR and PH are within the proper parameters touse standard tooling.

PT

PA90°

PRPH

PL

CB1Square Bend

CB = Classified Bend #PT = Part Material ThicknessPL = Part Length (bent leg)PA = Part Angle (degrees of bend)PH = Part Height (bent leg)PR = Part RadiusPC = Part Channel (inside)K = see catalogIncl. Angle = Included Angle

2

READY

READY Bender®

CB2 Concept Sketch

A READY Bender® is a CB2 tool when the PH dimension is too short to utilize a standard tool.(Call READY for minimum dimensions)

3

CB2Short Leg

PT

PAPR

PH

PL

CB = Classified Bend #PT = Part Material ThicknessPL = Part Length (bent leg)PA = Part Angle (degrees of bend)PH = Part Height (bent leg)PR = Part RadiusPC = Part Channel (inside)K = see catalogIncl. Angle = Included Angle

A READY Bender® CB3 bends where the bend angle is over 90° (120° max.).

A READY Bender® CB3 Extreme (over 110°) will most likely need to run off of a pad. This is to keepthe tool from sticking on the part.

READY Bender®

CB3 Concept Sketch

CB3Over Square

4

PT

PAPRPH

PL

CB = Classified Bend #PT = Part Material ThicknessPL = Part Length (bent leg)PA = Part Angle (degrees of bend)PH = Part Height (bent leg)PR = Part RadiusPC = Part Channel (inside)K = see catalogIncl. Angle = Included Angle

CB3 Extreme Concept Sketch

READY

A READY Bender® CB4 (on centerline) - the maximum angle remaining on centerline is105° included.

READY Bender®

CB4 Concept Sketch (on centerline)

CB4Under Square

5

PT

PAPRPH

PL

CB = Classified Bend #PT = Part Material ThicknessPL = Part Length (bent leg)PA = Part Angle (degrees of bend)PH = Part Height (bent leg)PR = Part RadiusPC = Part Channel (inside)K = see catalogIncl. Angle = Included Angle

READY

A READY Bender® CB4 (above centerline) includes angles over 105° will be abovecenterline.

READY Bender®

CB4 Concept Sketch (above centerline)

6

CB4Under Square

PT

PAPRPH

PL

CB = Classified Bend #PT = Part Material ThicknessPL = Part Length (bent leg)PA = Part Angle (degrees of bend)PH = Part Height (bent leg)PR = Part RadiusPC = Part Channel (inside)K = see catalogIncl. Angle = Included Angle

READY

READY Bender® CB5 bends will most likely need to run off of a pad. This is to maintainrocker retention in the saddle.

READY Bender®

CB5 Concept Sketch

CB5Zee Bend

7

PT

PAPR1PH

PLPR2

CB = Classified Bend #PT = Part Material ThicknessPL = Part Length (bent leg)PA = Part Angle (degrees of bend)PH = Part Height (bent leg)PR = Part RadiusPC = Part Channel (inside)K = see catalogIncl. Angle = Included Angle

READY

READY Bender® CB6 bends will most likely need to run off of a pad. This is to maintainrocker retention in the saddle.

READY Bender®

CB6 Concept Sketch

8

CB6Open Zee

PT

PAPR1PH

PLPR2

CB = Classified Bend #PT = Part Material ThicknessPL = Part Length (bent leg)PA = Part Angle (degrees of bend)PH = Part Height (bent leg)PR = Part RadiusPC = Part Channel (inside)K = see catalogIncl. Angle = Included Angle

READY

9

CB = Classified Bend #PT = Part Material ThicknessPL = Part Length (bent leg)PA = Part Angle (degrees of bend)PH = Part Height (bent leg)PR = Part RadiusPC = Part Channel (inside)K = see catalogIncl. Angle = Included Angle

READY Bender® CB7 bends a channel where the front of the saddle must be smaller thanstandard. Tooling can also be interlaced.

READY Bender® CB7 bends a channel where the front of the saddle must be smaller thanstandard.

READY Bender®

CB7 Concept Sketch (interlaced)

CB7 Concept Sketch (not interlaced)

PT

PAPH

PL

PR

PC

CB7Channel Bend

READY

READY Bender® CB8 has two CB5 bends where the front of the saddle is shorter thanstandard. Note: CB8 bends will most likely need to run off of a pad. This is to maintainrocker retention in the saddle. CB8 benders can also be interlaced.

READY Bender®

CB8 Concept Sketch

CB8Hat Bend

10

PR1 PR2

PA

PH

PLPT

PC

CB = Classified Bend #PT = Part Material ThicknessPL = Part Length (bent leg)PA = Part Angle (degrees of bend)PH = Part Height (bent leg)PR = Part RadiusPC = Part Channel (inside)K = see catalogIncl. Angle = Included Angle

READY

READY Bender®

CB13 Concept Sketch (large radius)

READY Bender® CB13 - the bend is a CB13 Large radius bend when the insidebend radius becomes too large to use the rocker diameter designated by the materialthickness.Extra overbend will be needed to end up with the proper bend angle.

11

CB13Large Radius Bend

PT

PRPA

PH

PL

CB = Classified Bend #PT = Part Material ThicknessPL = Part Length (bent leg)PA = Part Angle (degrees of bend)PH = Part Height (bent leg)PR = Part RadiusPC = Part Channel (inside)K = see catalogIncl. Angle = Included Angle

READY

READY

READY TECHNOLOGY, INC.333 Progress Rd. • Dayton, OH 45449 • 937-866-7200 • 800-0543-4355

Fax 937-866-7226

READY Benders® are covered by USA and international patents, and patents pending.©2004 READY TECHNOLOGY, INC., Catalog No. 504

Classified Bends (CB)

Square BendCB1

Short LegCB2

Over SquareCB3

prehem

Square Bend, RodCB21

Large Radius BendCB13

Return BendCB12

Two hits required

Gutted BendCB11

Hat BendCB8

Channel BendCB7

Open ZeeCB6

Zee BendCB5

Under SquareCB4

Full HemCB22

Selecting the right Bender is as easy as 1 . . . 2 . . . 3Fax this worksheet for FAST QUOTES

Fax: 937-866-7226 - send part prints

Company:

Contact Name: Title:

Address:

City, State, Zip:

Telephone: Fax:

Other Contacts:

Please describe your applicationThis will be formed in (please check)

❏ Stamping Die ❏ Automated Machine ❏ Press Brake, tonnage of press brake

Here are some of the most popular applications:

Annual production

Type of material formed

Tensile strength

CB = Classified Bend #

PT = Part Material Thickness

PL = Part Length (bent leg)

PA = Part Angle (degrees of bend)

PH = Part Height (bent leg)

PR = Part Radius

PC = Part Channel (inside)

Are tool marks* on part acceptable?*We specialize in forming even prepaint without tool marks.

Please Quote:Stamping Dies❏ Ready makes determination

❏ The Hard Inch Bender

❏ READY-2000

❏ The Hard Metric Bender

❏ READY-MET

❏ Compact Benders

Press Brake Tooling❏ Rotary Bender Press Brake Tools

❏ Conventional Vee Die Brake Tools

❏ Special Brake Tooling per print

Notes

Square Bend CB1

90° Bend

Over Square CB3

Form 120° In One Hit

Channel Bend CB7

Even Narrow Channels

Zee Bend CB5

Form Offsets In One Hit

Quote Reference #

Date

Distributor

1

PT

PA90°

PRPH

PL

PT

PAPR

PH

PL

PT

PAPRPH

PL

PT

PAPRPH

PL

PT

PAPR1PH

PLPR2

PT

PAPH

PL

PR

PC

PR1 PR2

PA

PH

PLPT

PC

PR, PAalsorequired

PH

PL

PT

PG

PR1

PR2

PA90°

PF

PH

PLPT

PT

PRPA

PH

PL

PR

PA

PH

PD

P-HEM

PL

PT

PT

PA90°

PRPH

PL PT

PAPRPH

PL

PT

PAPH

PL

PR

PC

Two hits required

2

3

PT

PAPR1PH

PLPR2

PT

PAPR1PH

PLPR2