Upload
others
View
6
Download
2
Embed Size (px)
Citation preview
Sep 19, 2014
Interns:
Khaled
ElmekawyComputer Aided DesignLecture 1
Dr./ Ahmed Nagib Elmekawy Sep 19, 20181
Finite Element Analysis Overview
2
Research and Development
3
Mathematical Model
4
5
Mathematical Model
6
Mathematical Model
7
Finite Element Analysis
The linear equation of motion for vibration is
𝑴 ሷ𝒙 + 𝑪 ሶ𝒙 + 𝑲 𝒙 = 𝑭
• 𝒙 , which is the displacement vector• ሷ𝒙 , which is the acceleration vector• 𝑴 , which is the Mass matrix• 𝑲 , which is the stiffness matrix• 𝑪 , which is the damping matrix• 𝑭 , which is the load vector
8
Finite Element Softwares
9
Finite Element Analysis
10
Finite Element Analysis
11
Finite Element Analysis
12
Static Analysis
For a linear static structural analysis, the global displacement vector 𝒙 is solved for in the matrix equation below:
𝑲 𝒙 = 𝑭
Assumptions made for linear static structural analysis are: • 𝑲 , which is the global stiffness matrix, is constant – Linear elastic material behavior is assumed – Small deflection theory is used • 𝑭 , which is the global load vector, is statically applied – No time-varying forces are considered – No damping effects
13
Axial Stress
14
Beam under the action of two tensile forces
15
Beam under the action of two tensile forces
16
Torsion Stress
17
Torsion Stress
18
Torsion Stress
19
Angle of Twist
20
Torsion of a Shaft with Circular Cross-Section
21
Torsion of a Shaft with Circular Cross-Section
22
Torsion of a Beam with the Square Cross-Section
23
Torsion of a Beam with the Square Cross-Section
24
Bending Stress
25
Bending Stress
26
Bending a Cantilever Beam under a Concentrated Load
27
Bending a Cantilever Beam under a Concentrated Load
28
Bending Stress
29
Bending Stress
30
Bending Stress
31
Bending Stress
32
Bending Stress
33
Bending Stress
34
Bending Stress
35
Bending of Curved beam
36
Displacement Stress in x direction
Finite Element Analysis
37
Finite Element Analysis
38
Static Analysis
39
Static Analysis
40
Static Analysis
41
Static Analysis
42
Static Analysis
43
Static Analysis
Linear vs Non Linear solveIn a linear analysis, the matrix equation [K]{x}={F} is solved in one iteration. That means the model stiffness does not change during solve : [K] is constant. A non linear solve allow stiffness changes and uses an iterative process to solve the problem. In a static structural analysis, ANSYS runs a non linear solve automatically when the model contains : - Non linear material laws : Plasticity, Creep, Gasket, Viscoelasticity … - Non linear contact : Frictionless, Rough, Frictional - Large deflection turned - Joints - Bolt pretension
44
Modal AnalysisThe linear equation of motion for free, un-damped vibration is
𝑴 ሷ𝒙 + 𝑲 𝒙 = 𝟎Assume harmonic motion:
𝒙 = 𝝓 𝒊 sin 𝜔𝑖𝑡 + 𝜃𝑖ሷ𝒙 = −𝜔𝒊
𝟐 𝝓 𝒊 sin 𝜔𝑖𝑡 + 𝜃𝑖
Substituting 𝒙 and ሷ𝒙 𝐢n the governing equation gives an eigenvalue equation:
−𝜔𝒊𝟐 𝑴 + 𝑲 𝝓 𝒊 = 𝟎
where𝜔𝑖: Natural Frequencies𝝓 𝒊 : Mode Shapes
45
Modal Analysis
46
Modal Analysis
47
Modal Analysis
48
Modal Analysis
Assumptions for Modal Analysis• [K] and [M] are constant: – Linear elastic material behavior is assumed – Small deflection theory is used, and no nonlinearities included – [C] is not present, so damping is not included – {F} is not present, so no excitation of the structure is assumed – Mode shapes 𝝓 𝒊 are relative values, not absolute
49
Modal AnalysisModal Results: • Because there is no excitation applied to the structure the mode shapes are relative values not actual ones. –Because a modal result is based on the model’s properties and not a particular input, we can interpret where the maximum or minimum results will occur for a particular mode shape but not the actual value.
50
Modal Analysis
51
Modal Analysis
52
Modal Analysis
53
Modal Analysis
54
Modal Analysis
55
Modal Analysis
56
Modal Analysis
57
Dynamic Analysis
58
Dynamic Analysis
59
Dynamic Analysis
60
Dynamic Analysis
61
Dynamic Analysis
62
Dynamic Analysis
63
Dynamic Analysis
64
Dynamic Analysis
65
Dynamic Analysis
66
Dynamic Analysis
67
Dynamic Analysis
68
Dynamic Analysis
69
Dynamic Analysis
70
Dynamic Analysis
71
Dynamic Analysis
72
Dynamic Analysis
73
Dynamic Analysis
74
Dynamic Analysis
75
Dynamic Analysis
76
Dynamic Analysis
77
Dynamic Analysis
78
Dynamic Analysis
79
80
Fluid-Structure Interaction
Solid Mechanics-Structural Analysis Fluid Dynamics
Solved by Finite Element Analysis Computational Fluid Dynamics (CFD)
81
Recent Computational Methodology
Finite Element Analysis Computational Fluid Dynamics (CFD)
CommercialSoftware
Ansys Mechanical, Abaqus Ansys Fluent, Ansys CFX, Open-foam
82
Recent Computational Methodology
83
Recent Computational Methodology
Fluid-Structure Interaction
84
85
Recent Computational Methodology
1 way FSI vs Two way FSI
Fluid-Structure Interaction
86
Fluid Structure Interaction
87
CFD Analysis Overview
88
Lecture Theme:
All CFD simulations follow the same key stages. This lecture will explain how togo from the original planning stage to analyzing the end results
Learning Aims:
You will learn:• The basics of what CFD is and how it works• The different steps involved in a successful CFD project
Learning Objectives:
When you begin your own CFD project, you will know what each of the stepsrequires and be able to plan accordingly
Introduction
89
Introduction CFD Approach Pre-Processing Solution Post-Processing Summary
What is CFD?
90
Computational Fluid Dynamics (CFD) is the science of predicting fluid flow, heat andmass transfer, chemical reactions, and related phenomena.
To predict these phenomena, CFD solves equations for conservation of mass,momentum, energy etc..
CFD can provide detailed information onthe fluid flow behavior:• Distribution of pressure, velocity, temperature,
etc.
• Forces like Lift, Drag.. (external flows, Aero, Auto..)• Distribution of multiple phases (gas-liquid, gas-
solid..)• Species composition (reactions, combustion,
• Much morepollutants..)
CFD is used in all stages of theengineering process:
• Conceptual studies of new designs
• Detailed product development
• Optimization
• Troubleshooting
• Redesign
CFD analysis complements testing and experimentation by reducingtotal effort and cost required for experimentation and data acquisition
Introduction CFD Approach Pre-Processing Solution Post-Processing Summary
CFD Applications
91
Introduction CFD Approach Pre-Processing Solution Post-Processing Summary
CFD Applications
92
Introduction CFD Approach Pre-Processing Solution Post-Processing Summary
CFD Applications
93
Introduction CFD Approach Pre-Processing Solution Post-Processing Summary
CFD Applications
94
Introduction CFD Approach Pre-Processing Solution Post-Processing Summary
How Does CFD Work?
95
ANSYS CFD solvers are based on the finite volume method• Domain is discretized into a finite set of control volumes
• General conservation (transport) equations for mass, momentum, energy,species, etc. are solved on this set of control volumes
Unsteady Convection Diffusion Generation
• Partial differential equations are discretized into a system of algebraic equations
• All algebraic equations are then solved numerically to render the solution field
ControlVolume*
EquationContinuity
X momentumY momentumZ momentum
Energy
1
uvwh
Introduction CFD Approach Pre-Processing Solution Post-Processing Summary
Step 1. Define Your Modeling Goals
96
• What results are you looking for (i.e. pressure drop, mass flow rate),and how will they be used?
• What are your modeling options?• What simplifying assumptions can you make (i.e. symmetry, periodicity)?
• What simplifying assumptions do you have to make?
• What physical models will need to be included in your analysis
• What degree of accuracy is required?
• How quickly do you need the results?
• Is CFD an appropriate tool?
Introduction CFD Approach Pre-Processing Solution Post-Processing Summary
Step 2. Identify the Domain You Will Model
97
• How will you isolate a piece ofthe complete physical system?
• Where will the computational domainbegin and end?
− Do you have boundary condition information atthese boundaries?
− Can the boundary condition types accommodatethat information?
− Can you extend the domain to a point wherereasonable data exists?
• Can it be simplified or approximated asa 2D or axi-symmetric problem?
Domain of Interest asPart of a LargerSystem (not modeled)
Domain of interestisolated and meshedfor CFD simulation.
SummaryIntroduction CFD Approach Pre-Processing Solution Post-Processing
Step 3. Create a Solid Model of the Domain
98
• How will you obtain a model of the fluid region?− Make use of existing CAD models?− Extract the fluid region from a solid part?− Create from scratch?
• Can you simplify the geometry?− Remove unnecessary features that would complicate meshing;fillets, bolts…Ϳ?
− Make use of symmetry or periodicity?• Are both the flow and boundary conditions symmetric /
periodic?
• Do you need to split the model so that boundaryconditions or domains can be created?
Original CAD Part
ExtractedFluid Region
Introduction CFD Approach Pre-Processing Solution Post-Processing Summary
Step 4. Design and Create the Mesh
99
• What degree of mesh resolution is required in each region ofthe domain?
− Can you predict regions of high gradients?• The mesh must resolve geometric features of interest and capture gradients
of concern, e.g. velocity, pressure, temperature gradients
− Will you use adaption to add resolution?
• What type of mesh is most appropriate?− How complex is the geometry?− Can you use a quad/hex mesh or is a tri/tet or hybrid mesh suitable?− Are non-conformal interfaces needed?
• Do you have sufficient computer resources?− How many cells/nodes are required?− How many physical models will be used?
Introduction CFD Approach Pre-Processing Solution Post-Processing Summary
Step 5. Set Up the Solver
100
• For a given problem, you will need to:
− Define material properties• Fluid
• Solid
• Mixture
− Select appropriate physical models• Turbulence, combustion, multiphase, etc.
− Prescribe operating conditions
− Prescribe boundary conditions at all boundary zones
− Provide initial values or a previous solution
− Set up solver controls
− Set up convergence monitors
Introduction CFD Approach Pre-Processing Solution
For complex problems solving a simplifiedor 2D problem will provide valuableexperience with the models and solversettings for your problem in a shortamount of time
Post-Processing Summary
Step 6. Compute the Solution• The discretized conservation equations are solved
iteratively until convergence• Convergence is reached when:− Changes in solution variables from one iteration to the
next are negligible
• Residuals provide a mechanism to helpmonitor this trend
− Overall property conservation is achieved•Imbalances measure global conservation
− Quantities of interest (e.g. drag, pressure drop) have reachedsteady values•Monitor points track quantities of interest
• The accuracy of a converged solution is dependentupon:
− Appropriateness and accuracy of physical models− Assumptions made− Mesh resolution and independence− Numerical errors
A converged and mesh-independentsolution on a well-posed problemwill provide useful engineeringresults!
Introduction CFD Approach Pre-Processing Solution Post-Processing Summary
10
101
Step 7. Examine the Results
102
• Examine the results to review solution andextract useful data
− Visualization Tools can be used to answer suchquestions as:
• What is the overall flow pattern?
• Is there separation?
• Where do shocks, shear layers, etc. form?
• Are key flow features being resolved?
− Numerical Reporting Tools can be used to calculatequantitative results:
• Forces and Moments
• Average heat transfer coefficients
• Surface and Volume integrated quantities
• Flux Balances
Examine results to ensure correct physical behavior andconservation of mass energy and other conservedquantities. High residuals may be caused by just a fewpoor quality cells.
Post-Processing SummaryIntroduction CFD Approach Pre-Processing Solution
Step 8. Consider Revisions to the Model
103
• Are the physical models appropriate?− Is the flow turbulent?− Is the flow unsteady?− Are there compressibility effects?− Are there 3D effects?
• Are the boundary conditions correct?− Is the computational domain large enough?− Are boundary conditions appropriate?− Are boundary values reasonable?
• Is the mesh adequate?− Does the solution change significantly with a refined mesh, or
is the solution mesh independent?− Does the mesh resolution of the geometry need to beimproved?− Does the model contain poor quality cells?
High residuals may be caused by justa few poor quality cells
Introduction CFD Approach Pre-Processing Solution Post-Processing Summary
Use CFD with Other Tools to Maximize its Effect
Prototype Testing Manufacturing
9.U
pd
ate
Mo
del
1. Define goals2. Identify domain
Pre-Processing
Problem Identification
3.4.5.6.
GeometryMesh PhysicsSolver Settings
7. Compute solution
Solve
8. Examine results
Post Processing
MeshCAD Geometry
Thermal Profile on Windshield
Final Optimized Design
Automated Optimization ofWindshield Defroster withANSYS DesignXplorer
104
Summary and Conclusions
105
• Summary:− All CFD simulations (in all mainstream CFD software products) areapproached using the steps just described
− Remember to first think about what the aims of the simulation areprior to creating the geometry and mesh
− Make sure the appropriate physical models are applied in the solver,and that the simulation is fully converged (more in a later lecture)
− Scrutinize the results, you may need to rework some of the earliersteps in light of the flow field obtained
1. Define Your ModelingGoals
2. Identify the Domain YouWill Model
3. Create a GeometricModel of the Domain
4. Design and Create theMesh
5. Set Up the Solver Settings6. Compute the Solution7. Examine the Results8. Consider Revisions to the
Model
Introduction CFD Approach Pre-Processing Solution Post-Processing Summary