Complete Guide to Sim Card Cloning

7/23/2019 Complete Guide to Sim Card Cloning

1/9

ITEMS NEEDED

1. Plain Wafer Card2. Sim card reader3. Software to extract Ki & IMSI4. Wafer Card Programmer5. Software to program the wafer card

INTRODUCTION

This is a simple and complete guide to sim cloning. With the help of this guide, you will be able to getyour sim cloned. This guide is applicable for cloning COMP128V1 version simcards. Eventhough the neweralgorithms cant be cloned now, almost 75% of us are using the cards with the COMP128V1 algorithm.Here comes the relevance of this guide. The working on new algorithms COMP128V2 & COMP128V3 aregoing on and lets hope to get this new algorithms cracked soon. Please dont use this guide for cheatingor harming others. Use this at your own risk and the author will not be responsible for any further is-

sues.

TIPS

Always search internet to find the items, softwares and news. Use search engines. They are free andespecially for our needs. You may not get these items from your local electronic shops. The main reasonis that only a few people know about this. A major group of electronic shops dont know what a silverwafer card is and what a wafer card programmer is.

Wafer Cards

The sim cards we get from the operator are not programmable. So we need to find some plain wafercards for the purpose.There are mainly three types of wafer cards suitable for GSM cloning. Gold Card,Silver Card and Green Card. Out of these Silver Wafer Cards are used most. So we will take a closer lookat Silver wafer Card. Silver wafer card consists of a PIC 16F876 and an EEPROM 24C64. These twoelectronic components are wired as shown in the below circuit.

You can buy plain silver cards from http://www.pulsat.com and if you dont find one there just searchfor silver wafer card at http://www.yahoo.com or http://www.google.com. If you cant find a plainwafer card in your place or if you cant get one from the internet, you can try the alternate method ofmanufacturing a silver wafer card by wiring the above circuit. It works fine with almost all the handsets.The only drawback is that, it wont fit inside the handset. We need to place it outside the handset.

Sim Card Reader

You can construct your own sim card reader economically with the following schematic. It uses minimumcomponents and works with almost all the scanning softwares. If you need to increase the speed of thescanning you can replace the 3.57Mhz crystal with a 6.12MHz or 7.14Mhz. The simcards will not supporta speed of more than 10Mhz. Also you can try other simcard readers from various providers. It can beUSB too. But make sure about the compatibility with the software you are using.

- - - - - - - - -A COMPLETE GUIDE TO SIM CLONING - - - - - - - - -- - - - - - - - - [email protected] - - - - - - - - -

- - - - - - - - -A COMPLETE GUIDE TO SIM CLONING - - - - - - - - -

- - - - - - - - - [email protected] - - - - - - - - -

WARNING:DONTUSETHISGUIDEFORANYILLEGALP

URPOSES.USETHISFOREDUCATIONALPURPOSEONLY


2/9


3/9


4/9- - - - - - - - -A COMPLETE GUIDE TO SIM CLONING - - - - - - - - -

- - - - - - - - - [email protected] - - - - - - - - -


WARNING:DONTUSETHI

SGUIDEFORANYILLEGALP

URPOSES.USETHISFORED

UCATIONALPURPOSEONLY


5/9- - - - - - - - -A COMPLETE GUIDE TO SIM CLONING - - - - - - - - -

- - - - - - - - - [email protected] - - - - - - - - -


WARNING:DONTUSETHI





6/9

- - - - - - - - - A COMPLETE GUIDE TO SIM CLONING - - - - - - - - -- - - - - - - - - [email protected] - - - - - - - - -


WARNING:DONTUSETHI





7/9

- - - - - - - - -A COMPLETE GUIDE TO SIM CLONING - - - - - - - - -- - - - - - - - - [email protected] - - - - - - - - -


WARNING:DONTUSETHI




Software to program the wafer card

Before checking the software to program the wafer card, we need to choose what to be programmed onthe plain wafer card. Anyway we need one file for PIC and one for the EEPROM. We can make the plainwafer card in to a 10 in 1 simcard, a 16 in 1 simcard or even a simcard with only two numbers. But if wehave the provision, i suggest to utilise the maximum from it. So i suggest a 16 in 1. Inorder to make thisdream come true, we need some additional softwares too. I suggest SimEmu 6.01 from http://www.simemu.cjb.net or pic-ador from http://borodza.com/pic-ador . With these softwares you cancreate the hex files for PIC and EEPROM.

Inorder to program these files to the wafer card, we need the software compatible with the programmer.If you are using a Millenium 2000VX Programmer you can use CardMaster with it. If using a DynamiteProgrammer, the programming software usually comes bundled with the programmer. You can use ICProgalso.

PROCESS

STEP1 : Insert the simcard in the simcard reader and use the software to extract the Ki, IMSIand ICCID of your simcard. Here i used Woron scan 1.09

STEP2 : Make the files for PIC and EEPROM with SimEmu Configurator or 16 in 1 SimEmuConfigurator by Pic-ador. If you are using the SimEmu Configurator by Pic-ador uncheck the A3A8checkbox under security. Please dont enable this even from the sim services menu. If enabled, it countsback to zero and when it reaches zero, all bad things can happen to your simcard. In the configuratoryou can set the number of ADN, FDN and SMS. You can use the formulae 16448 = (ADN - 51 ) x 32 +SMS x 176 + FDN x 32 must be less than 6480 for silver wafer cards. Then generate the Hex files for

PIC and EEPROM by clicking the Generate Hex file. With this configurator, in addition to the 16 numberslots, you can make the simcard a Motorola Test card too. In 16 in 1 configurator the positions are from0-9 and from A-F. Each position can be customised by induvidual PIN an PUK codes.


8/9


9/9

dream. Browse through the menu and find the Sim Tool Kit. Now it should be named as Sim-Emu 6.01.Open it and you can see the menus Configure, Select Phone and Information. Select Configure and goto config postion. It asks for the position. You can select any position from 0-9 and A-F. After selectingthe position it asks for a PIN and PUK. Always provide different PIN and PUK for each positions. It helpsus to switch to a number directly when the handset is switched on. After PIN and PUK it asks for KI,IMSI and ICCID. You can now recall the extracted values from STEP1 and enter it to appropriate fileds.Now you are done. You have a cloned simcard and moreover you are going to have a simcard with 16cloned mobile numbers.

A WORD FROM THE AUTHOR

I am a Computer hardware Engineer and I started this as a project for my Diploma in 1998. I managed toimpress the invigilator by showing the basic things that can do with a simcard reader. I was able toextract the ki in the beginning itself, but due to lack of information or a proper guide i was not able todo the rest of the things. The main issue was with the wafer cards. At first i thought that, with asimcard reader and a used sim card i was able to program the card. But continuous searching providedme the basic knowledge. The next major issue was the availability of wafer cards. I searched almostevery corner of india and nobody knows what a Silver Wafer card is. Atlast after 4 years, one of myfriends brought me some Silver wafer cards from UK. I searched many forums about sim cloning and icant find one succeeded from India. But i got some guides from some forums. But those were outdatedand use only two simcards in 1 and were bit confusing too. So after experiencing these difficulties, iplanned to make a guide for sim cloning. DONT USE THIS GUIDE FOR ANY ILLEGAL PURPOSES. USETHIS FOR EDUCATIONAL PURPOSE ONLY. I think i tried to explain each and everything in detail and if

you have any questions or suggestions, please let me know. [email protected]

DISTRIBUTION

You can freely make copies of the archive and distribute them as long as no alterations are made to thecontents.

DISCLAIMER

IN NO EVENT SHALL I BE LIABLE FOR ANY DAMAGES WHATSOEVER (INCLUDING WITHOUTLIMITATION, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION,LOSS OF BUSINESS INFORMATION, OR ANY OTHER PECUNIARY LOSS) ARISING OUT OFTHE USE OR INABILITY TO USE THIS PRODUCT.ALL THE SCHEMATICS & TRADEMARKS PROVIDED HEREIN ARE PROPERTY OF THEIR RESPECTIVE OWNERSOR COMPANIES

THANKS

Mr. KrishnaRaj & Mr. Binu for purchasing the programmer & wafer cards for me

Mr. Dejan Kaljevic for his circuits and software

SimEmu for his sim emulation oftware

Pic-ador for his sim emulation software

pulsat.com for the wafer cards

volny.cz/id2 for circuits

promosatuk.com for the programmer

forum.gsmhosting.com for the information



WARNING:DONTUSETHI


URPOSES.USETHISFOREDUCATIONALPURPOSEONLY

Documents

Complete Guide to Sim Card Cloning