Upload
others
View
0
Download
0
Embed Size (px)
Citation preview
COMPANY AND PRODUCTS PRESENTATION
August, 2013
BENFER SCHOMBURG International is a company owned by Mr. Giorgio Cocchi and the German
group SCHOMBURG GmbH & Co. KG.
Since 1965 Benfer produces adhesives for laying porcelain, ceramic tiles and natural stones, grouts for tile joints, waterproofing for screeds and walls.
These products are sold in Italy, in Europe and in the main international markets.
Benfer Schomburg works in a new, modern plant
located in Castelnuovo Rangone,
Close to the city of Modena.
Thanks to its and Schomburg group know how, Benfer can
offer both innovative and traditional building materials
at very competitive prices.
Crystalline waterproofings, foundation waterproofings, Construction joint sealants, epoxy and polyurethane based coatings for industrial floors, concrete repair mortars, moist
walls restoration systems,adhesives and grouts for ceramic tiles and natural stone
application, waterproofing for screeds ecc.
Permanent waterproofing of concrete from within
Control mix Concrete produced with 2% of Betocrete C-16 / C-17 after 28
days
BETOCRETE C-16 and C-17
Innovative admixtures for concrete structures protection against damages caused by water
BETOCRETE C-16 and C-17
BETOCRETE C-16 and C-17
Self Healing of static cracks up to 0,4 mm
BETOCRETE C-16 and C-17Typical applications:• Potable water tanks• Waste water treatment
facilities• Tunnels• Parking structures• Elevator pits• Precast elements• Foundations, etc.
Everywhere concrete must be waterproof
Example of application
Concrete floating Pontons, Hamburg, Germany
Betocrete-C17 in 5000 m³ of waterproof concrete for pontons.
WATERPROOFINGS FOR CEMENT BASED SUBSTRATESFOR SURFACE APPLICATION
ElastomericsAQUAFIN-2K/M
Cementitious
FlexiblesAQUAFIN-1K-Flex
RigidsAQUAFIN-1KAQUAFIN-IC
AQUAFIN-IC
• Crystalline waterproofing• Extraordinary adhesion• It resist to extreme hydrostatic pressure• For cement based substrates• It works against positive and negative
pressure• Approved for potable water tanks (NSF,
DVGW)• Self healing effect
Crystalline waterproofing for surface applicationCrystalline waterproofing for surface application
AQUAFIN-IC
Crystalline waterproofing for surface application
AQUAFIN-ICApplications:• Potable water tanks
• Waste water treatment plants
• Tunnels• Elevator pits• Manholes• Below grade
waterproofingCrystalline waterproofing for surface application
AQUAFIN-IC
Brush
Application methods
Dry shake Spray
Aquafin-IC application example
Waste water treatment plant in Palestine, USA
4000 m² positive side
Aquafin-IC application example
Car park in Guernsey, Great Britain
AQUAFIN-2K/M
• Resist to hydrostatic pressure up to 7 bars
• Excellent crack bridging up to 2.59 mm• Potable water approval according to
DVGW W347 & NSF61• Elongation > 115% (ASTM D412)• Freeze-thaw cycles resistant• It is a good substrate for tile laying• UV resistant• Bonds well to damp substrates
Elastomeric, cementations waterproofing
Cementitious - Elastomeric
AQUAFIN-2K/MApplications:• Water tanks• Swimming pools• Balconies• Below grade foundations• Water treatment plants• Marine structures and parks• Underneath tiles
waterproofing• Weather resistant
waterproofing
Cementious - Elastomeric
AQUAFIN-1K-flex
• Good bond to most substrates• Low crack bridging ability• Resistant to hydrostatic pressure• Elongation > 8% (ASTM D412)• Water vapour permeable• Resistant to freeze-thaw cycles
Flexible cementations waterproofing
Cementitious - Flexible
AQUAFIN-1K-flexApplications:• Terracies and balconies• Bathroom and showers • Every where underneath
tiles
Cementitious - Flexible
Consumption:• 2.3 kg/m2 at 2.0 mm dry
film thickness
AQUAFIN-1K
• Rigid waterproofing• Polymer modified• Good adhesion to most substrates• Withstand hydrostatic pressure• For mineral substrates• Resistant to positive and negative side
pressure• White or grey• Potable water approved ( DVGW W347
& NSF61)
Waterproofing slurry
Cementitious - Rigid
Waterproofing slurry
AQUAFIN-1KApplications:• Water tanks• Marine structures• Negative side water pressure• As base coat for AQUAFIN-2K/M
(against negative pressure)• Wall / floor junction
Cementitious - Rigid
Consumption:• 3.5 kg/m2 at 2.0 mm thickness • 4.5 kg/m2 at 2.5 mm thickness
SURFACE WATERPROOFING (surface applied)
High flexibilityCOMBIFLEX-C2
Bituminous
High flexibilityCOMBIFLEX-EL
COMBIFLEX-C2
• Seamless, flexible waterproofing• Rapid curing. Immediately rain-proof• Building pits can be closed after 24
hours• Easy to mix (2-components)• Trowel, roller or spray application• Bonds without Primer on dry or matt
damp substrates
2-comp.bituminous thick layer waterproofing
Bituminosi
COMBIFLEX-C2
Bituminous
• Crack briding >60 mm (ASTM C 863)• Tensile strength 1 N/mm2 (ASTM D 412)• Tensile elongation 169% (ASTM D 412)• Rapid chloride permeability : 66% (ASTM
C 1202)• Resistant to pressure up to 7 bars (DIN
1048)
Consumption:• 2.4 l/m2/2.0 mm• 6.3 l/m2/4.0 mm
COMBIFLEX-EL
• High build• Rapid curing. Immediately rain-proof• Crack bridging >2.0 mm• Easy to mix (2-components)• Trowel application • Bonds to dry and matt damp
substrates• The Primer is not necessary
Bituminous high build waterproof coating
Bituminous
COMBIFLEX-ELApplications:• Below grade• Foundations
Bituminous
Consumption:
• 3.75 l/m2 at 3.0 mm thickness
• 5.0 l/m2 at 4.0 mm thickness
ASO-JOINT-TAPE-2000 (2000-S)
Schomburg products selection
How to apply:
Sealing tapesApplication areas:• Construction / dilatation joints • Difficult / recurrent dynamics
cracks• Wall / floor joints
• Application on the positive side only• Application within AQUAFIN-2K/M• High flexibility: > 600% elongation• Size up to1.0 m wide available
Application on the positive side only
AQUAFIN-P4
Poliurethane resin, elastic,
injectable
AQUAFIN-CJ-SetConstruction joints
waterproofing: White tank
AQUAFIN-CJ4
• Generally approved for use in construction • Quick and strong swelling after the rain
protection has dissolved • Installation independent from weather
conditions as the patented specialized coating avoids early swelling efficiently
• Self-injecting effect by penetration into cracks and cavities.
• Reswellable• Extremely high form stability, will not become
sticky in summer at high temperatures • High anorganic content, therefore no material
fatigue
Bentonite waterstop with patented rain protection coating••
•
•
protection coating
INDU-FLEX CJ13
• Generally approved for use in construction• Swells upon in contact with water• No requirement for imperfect edging• Cause of defects will be reduced• Swelling process is reversible• Extremely high, form stability, will not become sticky at high temperatures• Non-absorbent
Hydrophlic joining strip
INDUFLOOR-IB1240
• Low solvent, moisture compatible, two component epoxy resin
• It blocks the oil – it works as a barrier against the capillary rising oil
• Bonds very well on wet concrete substrates
• Moist and vapour barrier
Oil and vapour barrier
INDUFLOOR-IB1240
Application areas:
It is used as a special primer for oil contaminated, but previously cleaned concrete substrates. It is used as primer for still damp concrete / bonded screed substrates that are to be treated with INDUFLOOR coating system or covered with conventional, classic floor finishes such as PVC, linoleum, carpet, parquet, tiles etc.
INDUFLOOR-IB2360
• Water emulsified, pigmented, two component epoxy resin
• Low odour• Resistant to diluted alkalis
and acids, heating oils and petrol
• Can be diluted up to 8% with water (use as a primer)
• Water vapour permeable • Excellent bond to many
substrates • Satin finish
Concrete sealer - aqueous
INDUFLOOR-IB2360
Areas of application:
It is used for sealing cement-based floor and wall surfaces , magnesium screeds, anhydrite screeds, and well compacted rolled or poured asphalt.
INDUFLOOR-IB3365
• Two component epoxy – polyurethane resin, solvent free, pigmented
• With Crack-bridging ability• Resistant to de-icing salts,
fuels, weak acid and alkalis, as well as to cleaning products at standard concentration
• Resistant to weather influences
Parking deck coating
INDUFLOOR-IB3365
Areas of application :
It is used as a crack bridging coating, which is impervious to liquids, on concrete and cement based screeds, on parking and access areas, in car parks and garages, on industrial floor areas and bridge parapets.
INDUFLOOR-IB3350-VC2
• Solvent free, pigmented, two component, conductive, epoxy resin
• Permanently conductive regardless of coating thickness and relative humidity
• Elastic • Resistant to mechanical and
chemical loads • High compressive and flexural
strenght
Volume conductive coating for EPA areas
INDUFLOOR-IB3350-VC2
Areas of application:
It is used for coating cement based surfaces that have to be equipped according to the ESD regulations. E.g.: electronics industry, PCB production, automotive industry, technical and research rooms, hospitals, computer rooms.
INDUFLOOR-IB-GWS 3
• High chemical resistance• Solvent free • Crack bridging • Mechanical resistance • Weather resistant • Conductive• Fullfils technical requirements
for coatings in the painting/lacquer industry, e.g. the automobile industry.
INDUFLOOR-IB-GWS 3
Areas of application:
Used in chemical companies, and storage/filling/handling plants as secondary containment to protect ground water from contact with harmful chemicals.
ESCO-FLUAT
• Transforms water soluble salts (chlorides and sulphates), into insoluble
• Avoids the invasion of lightly soluble salts into the wet, not yet hydrophobic restoration plaster
Impregnating solution for the trasformation of building damaging salts
THERMOPAL-GP11
• Interior or exterior • For uneven surfaces with excess moisture
or salt contained in natural-stone or brick-stone masonry
Air-entraining ground plaster according to WTA-Leaflet 2-2-91
THERMOPAL-SP
• Pre-blended dry mortar • Conforms to requirements in
accordance with WTA 2-9-04D
• Hydraulic cure • Very good bond to mineral
based substrates • Very good bond for the
following plaster / render coats
Mineral-based restoration splatterdash mortar
••
••
•
THERMOPAL-SR24
• Mineral-based pre-blended mortar
• High volume of entrained air • Vapor permeable • High salt storage capacity • Low consumption per surface
area • Ready for rubbing down at an
early stage • Hand or mechanical
application
Mineral-based restoration render - WTA
THERMOPAL-SR44
• Restoration plaster tested by WTA • Dry, premixed restoration plaster • Permeability to vapour diffusion • High salt storage • Manual or mechanical application • Easy and economical application • Low consumption
Mineralic restoration plaster
THERMOPAL-ASP45
• Mineral-based pre-blended mortar
• High volume entrained air • Vapor permeable • High capillary storage • High water absorption capability • Low consumption • Manual or mechanical
application • Can be applied in a single layer
from 20-30 mm • For interior use
Mould restoration plaster system
••••••
•
•
BENFERCURE PLUS
• Repair of concrete columns • Repair of under-surfaces of concrete
balconies • Repair and finishing of concrete walls with
defects such as ballast nests and holes caused by spacers
• Repairs of concrete deterioreted by weather and by corrosion of steel reinforcement bars
• Repairs of concrete industrial ramps and floors
• Shaving of cement based screeds before tiles application
• Conforms to EN 1504-3 R3 class •
Anti-shrinkage, fibre-reinforced, thixotropic cement mortar
BENFERCURE FERRI
• Anti-corrosion protection for concrete reinforcing rods
• Promoted adhesion during concrete pouring between old and fresh coats and between concrete and repair mortars
•
•
INDUFLOOR-IB4015
• INDUFLOOR-IB4015 is a two component, filled epoxy resin mortar with the following properties:
- Solvent free
- high compressive and flexural strenght
- withstands high mechanical loading
- No primer / bonding agent necessary
•
Epoxy mortar
•
ASODUR-K900
• ASODUR-K900 is a two component low viscosity, solvent free epoxy resin with an exceptional bond to concrete, screed, stone, etc.
• Very good penetration • High adhesion strenght • Rapid hardening • Resistant to chemicals • Water and frost resistant
Casting and adhesive resin
STARPRIM
• For absorbent and non-absorbent substrates
• For interior and exterior use
• Ready to use • Solvent free • Rapid drying • Low emissions
Primer for absorbent and non-absorbent substrates
ASODUR-SG3
• Solvent free • Low viscosity • Moisture blocking • Low water vapour emission • Very low WDD volue = 0.2 gr/m² x d,
to DIN EN ISO 7783-1 • Water and frost resistant• Resistant to dilute alkalis, acids water-
based salts solutions and lubrificants
Moisture blocking, two component epoxy Primer
BENFERFLEX C2
• High flexibility • No vertical sliding • Ideal for exterior • Ideal for heavy mosaic application • Ideal for porcelain• Ideal for large sizes • Application up to 15 mm thickness •
BENFERFLEX C2
• Higly flexible fibre-reinforced adhesive with high special polymer content , thixotropic, frost resistant, with no vertical sliding.
• For wall and floor application of porcelain and ceramic tiles even on smooth and non absorbent substrates.
• Ideal for overlapping and large sizes even on heated screeds.
• CSTB certified with Avis Technique n° 151 MC 157. Classified C2-TE S1 to EN12004
LIGHTFLEX
• Easy and smooth application • High initial grab • Good sag resistance • Variable, use also as a flow-bed
adhesive • For interior and exterior use • Fullfils the required criteria for a
flexible adhesive • Classified C2 TE S1 to DIN EN 12004• Dust reduced •
Universal flexible adhesiveespecially light with high yeld
••••
••
•••
LIGHTFLEX
• It is used as a thin bed adhesive and flow bed adhesive with a high yeld for fixing vetrified and earthenware tiles, ceramic tiles with low water absorption < 0,5%, clincker, mosaic and natural stone not translucent or sensitive to decoloration.
• Uneven wall or floor substrates can be levelled out with LIGHTFLEX up to a thickness of 15 mm before start tiling.
• Due to the low weight transportation to the site is considerably easier.
Universal flexible adhesiveespecially light with high yeld
BENFERGRIP+
• Extra-white • High resistant to vertical sliding • Application without the need for
spacers • Perfect for glass and ceramic
mosaic • Perfect for klinker and thick tiles • Its smooth consistency reduces
fatigue • Long open time •
STEPBOARD SILENT
• Effective acustic insulation and stress barrier under tiles, natural stone and parquet
• Can be applied on screeds, old floors and wooden substrates
• Sound barrier protection up to 21db • Low thickness, just 12 mm • Suitable for underfloor heating systems• Ecologic• Simple to handle • Tile’s size from 200 to 2400 cm²
Stress barrier and highly sound dampening layer
STEPBOARD SILENT• STEPBOARD SILENT consist of a 9 mm thick Polyester-fibre
board with an optimal density for the best insulation, and a Poyester-fibre fleece 3 mm thick.
• This sandwich board is very rigid and resistant to compression.
• Using a flexible adhesive it can be covered with all kind of top layers, with the exception of parquet.
ADF-Balkonfolie
• Waterproofing membrane for balconies and terraces and for bonded waterproofing in combination with tiling in wet areas
• As a decoupling membrane for difficult substrates which are at risk of cracking
Waterproofing and decoupling membrane
ADF-Systemkleber
• Tested to EN 12004, C1TE • Water repellent • Easy to use • Good slump resistance • Plymer modified • For interior and exterior•
Hydrophobic special adhesive
DEKOGROUTAntibacterial, flexible, smooth cement-based grout
• Antibacterial and mould resistant • Water repellent • Resistant to freeze/thaw cycles• Free from hazardous siliceous fine quartz dust• Good application and wash off properties • Smooth surface and wide color range• For interior, exterior and under water • Fulfils the requirements of EN 13888, CG2WA • For joints 1-6 mm wide • Vapour permeable • Suitable for floor and wall heating • EC1: very low emissions • Colours matched to the ESCOSIL-2000 silicone
system
• DEKOGROUT is suitable for grouting glass mosaic, vitrified and fully vitrified clay tiles, brick tiles, tile slips, floor clinkers in bathrooms, showers and living rooms, on terraces, balconies and loggia, as well as in facades, swimming pools, commercial areas, and on heated and flow screeds.
• Furthermore DEKOGROUT is suitable for jointing of natural stones, if the product specific properties of the natural stone material permit this and discoloration can be excluded. We recommend CRISTALLFUGE for the jointing of natural stones.
DEKOGROUTAntibacterial, flexible, smooth cement-based grout
DEKOGROUTAntibacterial, flexible, smooth cement-based grout
Colour range:
DEKOGROUT 2/12Antibacterial, flexible, cement-based grout
• Antibacterial and mould resistant • Water repellent • Resistant to freeze/thaw cycles• Free from hazardous siliceous fine quartz dust• Good application and wash off properties • Smooth surface and wide color range• For interior, exterior and under water • Fulfils the requirements of EN 13888, CG2WA • For joints 2-12 mm wide • Vapour permeable • Suitable for floor and wall heating • EC1: very low emissions • Colours matched to the ESCOSIL-2000 silicone
system
• Special flexible grout, fast setting, for joint from 2 to 12 mm wide. • Dekogrout 2-12 is composed of special cements, aggregates, and additives
and is designed to provide high mechanical resistance , good flexibility and low water absorption with an attractive aesthetic appearance.
• They are available in various colors, for joints from 2 to 12 mm wide.
DEKOGROUT 2/12Antibacterial, flexible, cement-based grout
DEKOGROUT 2/12Antibacterial, flexible, cement-based grout
Colour range:
HF05-BrillantfugeHigh strenght, flexible cement based grout
• High strenght cement based grout • Increased abrasion resistance • Water repellent• Resistant to freeze/thaw cycles • Mould resistant • Resistant to high pressure cleaning • Free from hazardous siliceous fine quartz dust• For interior, exterior and under water • Fulfils the requirements of EN 13888, CG2WA • For joints from 3 to 20 mm wide • Vapour permeable • Good application and wash off properties• Suitable for floor and wall heating • Colours matched to the ESCOSIL-2000 silicone system
• Due to its high mechanical performance and abrasion resistance, HF05-Brillantfuge is especially suitable for grouting tiles in swimming pools, washing plants, commercial kitchens, sales rooms, commercial areas, industrial areas and workshops.
• Furthermore HF05-Brillantfuge can be used on heated and flow screeds in bathrooms, showers and living rooms, on terraces, balconies and loggia as well as facades. HF05-Brillantfuge can be used in heavy duty areas e.g. where cleaning equipment, high pressure steam cleaning or scouring vacuums are present.
• Furthermore the dense grout joints give increased resistance to cleaning chemicals. Neutral or alkaline cleaners can be used unrestricted.
HF05-BrillantfugeSigillante per fughe a base di cemento ad alta resistenza, flessibile
DEKOGROUT-2KTwo part waterproof adhesive-grouting mixture. Hygienic, acid, stain, bacteria and mould resistant. Beautiful finish, ease of application.
• Antibacterial and mould resistant • Water repellent• Resistant to freeze/thaw cycles • Good application and wash-off properties• Smooth surface and wide colour range (24 colours)• Resistant to chemical and mechanical loads • For interior, exterior and under water• Fulfils the requirements of EN 13888, CG2 and EN12004 R2T• For joints from 2 -10 mm wide • Suitable for floor and wall heating• Colours matched to the ESCOSIL silicone system
• DEKOGROUT-2K is a special two part product with an epoxy resin base, selected quartzes and special additives suitable for sticking and grouting all types of ceramic floorings and coverings onto a wide variety of bases, waterproof and resistant to chemical and mechanical loads.
• Designed to harden rapidly and without shrinking, easily cleaned with water, DEKOGROUT-2K is waterproof, hygienic, acid, stain, bacteria and mould resistant. It guarantee an aspect and a resistance to ageing and a cleanness of the joint that can not be obtained with traditional grouts.
DEKOGROUT-2KTwo part waterproof adhesive-grouting mixture. Hygienic, acid, stain, bacteria and mould resistant. Beautiful finish, ease of application.
DEKOGROUT-2K KITGrouting kit for 2 m of glass mosaic 20x20 mm
CONTAINS: • DEKOGROUT-2K, coloured two
components epoxy grout 2,5 kg
• DEKOGROUT-2K CLEANER (box10 pcs) for an easy cleaning after grouting
• sigillante 0,500 ml • DEKOFELT (box 10 pcs) special felt to
remove the grout excess• DEKOSPONGE (box 10 pcs) special
sponge designed for a perfect finish
2
THANK YOU FOR YOUR ATTENTION!
Tel. +39 059 [email protected]@benfer.itwww.benfer.it