Upload
others
View
0
Download
0
Embed Size (px)
Citation preview
2-46
2-46
TRA
NSD
UC
ERS
Load Cells(Load Transducers)
Outline
Compressive
Tensile
Tensile &compressive
Component
Special
Other
Compact Tension/Compression Load Cell●Compact ●50 N to 20 kN
To Ensure Safe Usage
If impact is expected in receiving tensile loads,
select a load cell with the rated capacity higher
by one rank than the operating load.
LUX-B-ID
*For TEDS, see page 9-17.Note: For transducers providing both positive and
negative output values an average of both values are written as the rated output.
LUX-B-50N-IDLUX-B-100N-IDLUX-B-200N-IDLUX-B-500N-IDLUX-B-1KN-IDLUX-B-2KN-IDLUX-B-5KN-IDLUX-B-10KN-IDLUX-B-20KN-ID
±50 N±100 N±200 N±500 N
±1 kN±2 kN±5 kN
±10 kN±20 kN
8 kHz11 kHz14 kHz16 kHz21 kHz27 kHz18 kHz21 kHz25 kHz
3 N·m
10 N·m
80 N·m
Rated CapacityNatural Frequencies
(Approx.)Recommended
Tightening TorqueModels
Suitable for measuring and controlling loads applied to small-scale presses and press-fitting devices
Compact & lightweight design with a screw-shape load receiving portion facilitates easy installation to equipment. Furthermore, the cable is connected using a connector, therefore there are no wring problems, and cable replacement is easy. Work is also possible if the cable is replaced with one resistant to repeated bending (Flexible cable). Please attach a suffix of M1Z3K to the model name.
●High sensitivity●Waterproof connector●Stainless steel ●Easy installation
Safe Overloads 150%Natural Frequencies See table below.Material SUS (Metallic finish)Weight Approx. 260 g (5 to 20KN) Approx. 90 g (500N to 2KN) Approx. 50 g (200N or less) (Excluding cable) Degree of Protection IP67 (IEC 60529)
Rated Capacity See table below.Nonlinearity Within ±0.1% RO (2KN or less: Within ±0.15% RO)Hysteresis Within ±0.1% RO (2KN or less: Within ±0.15% RO)Repeatability 0.05% RO or lessRated Output 1.3 mV/V or more 100 N to 1 kN: 0.9 mV/V or more 50 N: 0.85 mV/V or more
Safe Temperature -20 to 80°CCompensated Temperature -10 to 70°CTemperature Effect on Zero Within ±0.005% RO/°C (50N to 200N: Within ±0.03% RO/°C)Temperature Effect on Output Within ±0.005%/°C
Safe Excitation 15 V AC or DC (50N to 200N: 10 V AC or DC)Recommended Excitation 1 to 10 V AC or DC (50N to 200N: 1 to 5 V AC or DC)Input Resistance 375 Ω ±1.5%Output Resistance 350 Ω ±1%Cable Model: TE-45 6-conductor (0.08 mm2) chloroprene shielded cable, 4.4 mm diameter by 3 m long Sensor side: Terminated with a connector plug 213FCW-8P Measuring instrument side: Bared at the tip (Shield wire is not connected to the case.)
SpecificationsPerformance
Environmental Characteristics
Electrical Characteristics
Mechanical Properties
Bared at the tip(For TEDS installation)
LUX-B-IDRecommended
products for combination
●Physical quantity indication ●Static measurement ●Dynamic measurement
→ 3-91 → 3-94 → 3-27
Data Logger UCAM-60 series
→ 3-5 → 3-63
Strain AmplifierDPM-900 series
Universal RecorderEDX-100A
Instrumentation AmplifierWGA-680A
Instrumentation AmplifierWGA-910A
→ 3-55
Universal RecorderEDX-200A
Mount base CX (Page 2-48) Ball joint TU (Page 2-75)Whirl-stop coupling TSC (Page 2-48)Whirl-stop brackets TS (Page 2-48)
Optional Accessories
2-47
TRA
NSD
UC
ERS
2-47
Load Cells(Load Transducers)
Outline
Compressive
Tensile
Tensile &compressive
Component
Special
Other
M4 SR10
(7)
16
26
9
φ26
(41)(38)
Standard cable (TE-45)
Standard cable (TE-45)
Standard cable (TE-45)
(95)Minimum mounting dimensions when bending the cable
M4 d=4
2×φ3 d=2
φ18
Thin nut SUSThin nut SUS
SR30M6
φ28(43)(38)
14.5
(10)
22
37
M6 d=7
2×φ4 d=2Minimum mounting dimensions when bending the cable
(95)
φ21
(100)Minimum mounting dimensions when bending the cable
M12×1.25SR30
Thin nut SUS
(C)
(B)
A
φ43
(58)(38)
D
M12×1.25 d=12
2×φ5 d=3
φ33
■Dimensions
■Dimensions of mount base
LUX-B-5KN to 20KN-ID
LUX-B-5KN-IDLUX-B-10KN-IDLUX-B-20KN-ID
495153
26.527.527
151616
19.51818
A B C DModels
LUX-B-50N to 200N-ID LUX-B-500N to 2KN-ID
●Mount base CX
LUX-B-50N-IDLUX-B-100N-IDLUX-B-200N-IDLUX-B-500N-IDLUX-B-1KN-IDLUX-B-2KN-IDLUX-B-5KN-IDLUX-B-10KN-IDLUX-B-20KN-ID
CX-2
CX-4
CX-6
43
48
68
26
29
44
9
13
20
35
39
57
7
12
20
2.5
5
10
4.5
7
13
4.5
7
13
5
5
7
18±0.1
21±0.1
33±0.1
3
4
5
4.5
6
6
40 g
100 g
350 g
Mount Bases φA φB φC φD E F G φH φJ L φM Weight
(Approx.)NLoad cells
Hexagon socket head bolts for connection among load cells, mount bases, and locking pins are attached to the mount base.
R1
3×φJ through holeat equal distance
φH through hole
2×φM
φD
L
φCφA
G
N
E
F
φB
30°
0.200.06
0.20.1
0.20.1
2-48
2-48
TRA
NSD
UC
ERS
Load Cells(Load Transducers)
Outline
Compressive
Tensile
Tensile &compressive
Component
Special
Other
■Dimensions in combination with special accessories
●In combination with mount base (CX)
●In combination with ball joint (TU), whirl-stop coupling (TSC) and whirl-stop bracket (TS)
LUX-B-50N-IDLUX-B-100N-IDLUX-B-200N-IDLUX-B-500N-IDLUX-B-1KN-IDLUX-B-2KN-IDLUX-B-5KN-IDLUX-B-10KN-IDLUX-B-20KN-ID
LUX-B-50N-IDLUX-B-100N-IDLUX-B-200N-IDLUX-B-500N-IDLUX-B-1KN-IDLUX-B-2KN-IDLUX-B-5KN-IDLUX-B-10KN-IDLUX-B-20KN-ID
CX-2
CX-4
CX-6
TSC-2MTSC-2F
TSC-4MBTSC-4FB
TSC-6MBTSC-6FB
TS-2
TS-4B
TS-6B
TU-6B
TU-12B
TU-18B
43
48
68
44.7
50.5
67
18
30
42
6
12
18
9
16
23
33
49
697173
102
165
237239241
120
195
279281283
Mount Bases
Whirl-stop Couplings Whirl-stop Brackets Ball Joints
φA
φEC(A)
B
FD(B)
Load Cells
Load Cells
(The patch should be prepared by user or CA-2F or the equivalent should be used.)(This combination does not apply to tensile load measurement.)
(This combination does not apply to compressive load measurement.)
*Note that the Whirl-stop Bracket TS is not a safety device to be used when a load exceeding the safe overload is applied. If exceeding safe overload is applied, install a safety device on customer side before use.
To Ensure Safe Usage● For tensile load measurement, take care never
to exceed the safe overload rating.● Pay attention to strength of fastened parts which is screwed into
the LUX-B. When using the LUX-B with rated capacity more than 2 kN or more, use the fastened parts made of a material with tension strength more than 800 N/mm2
Typical recommended material: SUS630 (H900) HRC40 to 47 SCM435 HRC30 to 38
B
φA
Patch
Load cell
Locking pin(Mount baseaccessory)
Mount base
Hex. socket head bolt(Mount base accessory)
F
(B)
(A)
D
C
φE
Ball joint (TU)
Split pin
Whirl-stop coupling M (TSC-M)*
Hex. socket head bolt
Whirl-stop bracket (TS)*
Ball joint (TU)
Split pin
Stripper bolt
Whirl-stop coupling F (TSC-F)
Load cell
Thin nut(Load cell accessory)
2-49
TRA
NSD
UC
ERS
2-49
Load Cells(Load Transducers)
Outline
Compressive
Tensile
Tensile &compressive
Component
Special
Other
30000
40000
20000
10000
00 20 40 60 80 100
40000
30000
20000
10000
00 20 40 60 80 100
40000
50000
30000
20000
10000
00 20 40 60 80 100
Load in Sensitivity Direction (% RO)Load in Sensitivity Direction (% RO)
Load in Sensitivity Direction (% RO)
Safe
Ben
din
g M
omen
ts(N
·mm
)
Safe
Ben
din
g M
omen
ts(N
·mm
)Sa
fe B
end
ing
Mom
ents
(N·m
m)
1715
f
F: 500N (50%RO)
4000
3000
2000
1000
0 0 20 40 60 80 100Load in sensitivity direction (% RO)
Safe
Ben
din
g M
omen
ts (N
·mm
)
2500
2000
1500
1000
500
00 20 40 60 80 100
4000
3000
2000
1000
00 20 40 60 80 100
4000
3000
2000
1000
00 20 40 60 80 100
Load in Sensitivity Direction (% RO)Load in Sensitivity Direction (% RO)
Load in Sensitivity Direction (% RO)
Safe
Ben
din
g M
omen
ts(N
·mm
)
Safe
Ben
din
g M
omen
ts(N
·mm
)Sa
fe B
end
ing
Mom
ents
(N·m
m)
800
600
400
200
00 20 40 60 80 100
400
300
200
100
00 20 40 60 80 100
800
600
400
200
00 20 40 60 80 100
Load in Sensitivity Direction (% RO)Load in Sensitivity Direction (% RO)
Load in Sensitivity Direction (% RO)
Safe
Ben
din
g M
omen
ts(N
·mm
)
Safe
Ben
din
g M
omen
ts(N
·mm
)Sa
fe B
end
ing
Mom
ents
(N·m
m)
■LUX-B safe bending moments (N·mm)
●Figures below show the safe bending moments against lateral loads with a load applied in sensitivity direction (Vertical direction)
How to obtain safe lateral loads
Graph-1
Fig. 1
LUX-B-50N to 200N
LUX-B-500N to 2KN
LUX-B-5KN to 20KN
Rated Capacity: 50 N
Rated Capacity: 500 N
Rated Capacity: 5 kN
Rated Capacity: 100 N
Rated Capacity: 1 kN
Rated Capacity: 1 kN
Rated Capacity: 10 kN
Rated Capacity: 200 N
Rated Capacity: 2 kN
Rated Capacity: 20 kN
Shown here is an example calculating the safe lateral load when the LUX-B-1KN-ID receives a load in sensitivity direction (Vertical direction). (See Fig. 1.)
The safe lateral load f (N) which is applied to the screw at the distance of 17 mm from the center of the moment when a load of 500 N (50% the rated capacity) is applied in sensitivity direction and is obtained as follows:
According to Graph-1, safe bending moment, M, is approximately 2500 N・m when a load of 50% the rated capacity is applied in sensitivity direction. Since the relation between safe lateral load f, and safe bending moment M is M = f・L,
Therefore, the safe lateral load f is 147.1 N.
M=f・L
15L
M: Safe bending moments (N・mm)
F: Load in sensitivity axis (N)
f: Safe lateral load (N)Center of moment
15L
M=f・L
M: Safe bending moments (N・mm)
F: Load in sensitivity axis (N)
f: Safe lateral load (N)
Center of moment
M=f・L
20L
M: Safe bending moments (N・mm)
F: Load in sensitivity axis (N)
f: Safe lateral load (N)
Center of moment
f = =ML
250017
=147.1N
2-50
2-50
TRA
NSD
UC
ERS
Load Cells(Load Transducers)
Outline
Compressive
Tensile
Tensile &compressive
Component
Special
Other
LUR-A-SA1Compact Tension/Compression Load Cell
Compact & lightweightTension/Compression load cellsCompact & lightweight LUR-A-S1 series are easy to use tension/compression load cells. They are used in various fields ranging from production lines to experiments. Standard Accessories
Optional Accessories
Hexagon socket head setscrew M3, L=4
Ball joint TU (Page 2-75)
LUR-A-50NSA1LUR-A-100NSA1LUR-A-200NSA1LUR-A-500NSA1LUR-A-1KNSA1LUR-A-2KNSA1
±50 N±100 N±200 N±500 N
±1 kN±2 kN
2 kHz4 kHz5 kHz9 kHz
14 kHz20 kHz
Rated CapacityNatural Frequencies
(Approx.)Models
■Dimensions
Connector plugPRC03-12A10-7M
Safe Overloads 150%Natural Frequencies See table below.Weight Approx. 70 g (Excluding cable)
Rated Capacity See table below.Nonlinearity Within ±0.5% ROHysteresis Within ±0.5% RORated Output 0.5 mV/V or more 50NSA1: Approx. 0.4 mV/V
Safe Temperature -10 to 70°CCompensated Temperature 0 to 70°CTemperature Effect on Zero Within ±0.05% RO/°C (50NSA1: Within ±0.1% RO/°C)Temperature Effect on Output Within ±0.05%/°C (50NSA1: Within ±0.1%/°C)
Safe Excitation 7 V AC or DCRecommended Excitation 1 to 2 V AC or DCInput Resistance 350 Ω ±2%Output Resistance 350 Ω ±2%Cable 4-conductor (0.05 mm2) chloroprene shielded cable, 3 mm diameter by 5 m long, terminated with a connector plug PRC03-12A10-7M (Shield wire is connected to the case.)
●φ28 mm ●50 N to 2 kN
SpecificationsPerformance
Environmental Characteristics
Electrical Characteristics
Mechanical Properties
1212
(15)
5
8
35
φ28
φ14
(φ7)
(25)
2xM3 (For setscrew)
2×M8, P=1.25, d=8
LUR-A-SA1Recommended
products for combination
To Ensure Safe Usage●Consult with our sales engineer when using in
combination with special accessories.●Special accessories for tensile loads should be
mounted to the load cell at our factory.●When using for tensile loads, be sure to fix the
load cell with accessory hexagon socket head setscrews (M3, L=4).
*The connector plug at the cable tip may be replaced with R05-PB5M, when ordering, suffix "-R " to the model number.
●Physical quantity indication
●Static measurement ●Dynamic measurement
→ 3-91 → 3-27
Data Logger UCAM-60 series
→ 3-5 → 3-63
Strain AmplifierDPM-900 series
Universal RecorderEDX-100A
Instrumentation AmplifierWGA-910A
→ 3-55
Universal RecorderEDX-200A
→ 3-78
Sensor InterfacePCD-400A/430A
* The models for high-temperature up to 150°C are available. Inquiries are welcome.
2-51
TRA
NSD
UC
ERS
2-51
Load Cells(Load Transducers)
Outline
Compressive
Tensile
Tensile &compressive
Component
Special
Other
LU-ETension/Compression Load Cell
Hermetically-sealed structure with inert gas filled in.Tension/Compression load cellsThe detection portion is hermetically sealed with inert gas filled in to prevent aging deterioration and to ensure reliability and stability for a long period of time.
●500 N to 200 kN
Rated Capacity See table below.Nonlinearity Within ±0.2% ROHysteresis Within ±0.1% RORepeatability 0.1% RO or lessRated Output 2 mV/V ±0.2%
Safe Overloads 150%Natural Frequencies See table below.Weight See table below.
Safe Excitation 20 V AC or DCRecommended Excitation 1 to 10 V AC or DCInput Resistance 350 Ω ±0.5%Output Resistance 350 Ω ±0.5%Cable 4-conductor (0.3 mm2) chloroprene shielded cable, 7.6 mm diameter by 5 m long, terminated with a connector plug PRC03-12A10-7M (Shield wire is connected to the case.)
Safe Temperature -30 to 85°CCompensated Temperature -10 to 70°CTemperature Effect on Zero Within ±0.005% RO/°CTemperature Effect on Output Within ±0.005%/°C
SpecificationsPerformance
Environmental Characteristics
Electrical Characteristics
Mechanical Properties
Optional Accessories
Saddle CA-B (Page 2-72)Mount base CF (Page 2-72)Rotating attachment RJ (Page 2-74)Ball joint TU (Page 2-75)Hook THC (Page 2-75)Shackle TRC (Page 2-76)
LU-50KELU-100KELU-200KELU-500KELU-1TELU-2TELU-5TELU-10TELU-20TE
±500 N±1 kN±2 kN±5 kN
±10 kN±20 kN±50 kN
±100 kN±200 kN
1.54 kHz2.16 kHz3.28 kHz2.66 kHz
4.2 kHz4.97 kHz
3.5 kHz3.14 kHz
2.5 kHz
2.8 kg
5.0 kg9.5 kg
22.0 kg
CA-1B
−
CF-50
CF-80
−
Rated CapacityNatural
Frequencies(Approx.)
Weight*(Approx.) Saddles Mount BasesModels
*Excluding cable
* TEDS-installed models are available. Inquiries are welcome.
2-52
2-52
TRA
NSD
UC
ERS
Load Cells(Load Transducers)
Outline
Compressive
Tensile
Tensile &compressive
Component
Special
Other
H B(8)
4×E
F
12
12
2.3
SR
M3
3(4)
4
O
(40)
(40)
22 N
A
PatchBefore tensile measurements, remove the patch.
(K)
(C)
(C)
φD
φD
(L)
(L)
φ12
.5±1
JJ
B
A
(70)
(70)
H
R1/2
R1/2
(90°)
Cable
(45°)
M3, M
2×M5, M
4×E
G
G
(K)
SR
G
G
2×M5(90° position)
PatchBefore tensile measurements, remove the patch.
Cable
Flexible tubeApprox. 300 mm
Flexible tubeApprox. 300 mm
F
*Rotation attachment RJ is not applicable for compressive load measurement.*Special accessories for tensile loads should be mounted at our factory.*Dimensions A and B are approximate, since the ball joint is screw-in type.
●In combination with rotating attachment (RJ) and ball joint (TU)
A (A
pp
rox.
)B
(Ap
pro
x.)
F
G φD
φE
C
2
1
3
3
■Dimensions in combination with special accessories
LU-50KELU-100KELU-200KELU-500KELU-1TELU-2TELU-5TELU-10TELU-20TE
RJ-02
RJ-05RJ-1RJ-2RJ-5RJ-10RJ-20
TU-8
TU-12TU-14TU-18TU-26
217
262283304463678842
195
232246262393573706
125
140160160235315414
22
30374270
105136
11
161723376075
8
121418254050
M8, P=1.25
M12, P=1.75M14, P=2M18, P=1.5M26, P=2M36, P=2M50, P=3
1.4 kN2.9 kN5.8 kN
14.7 kN29.4 kN58.8 kN
136.3 kN
②RotatingAttachments ③Ball Joints A
(Approx.)B
(Approx.) C φD φE F GStatic Breaking Loads (Approx.)①Load Cells
LU-ERecommended
products for combination
●Physical quantity indication
●Static measurement ●Dynamic measurement
→ 3-91 → 3-27
Data Logger UCAM-60 series
→ 3-5 → 3-63
Strain AmplifierDPM-900 series
Universal RecorderEDX-100A
Instrumentation AmplifierWGA-910A
→ 3-55
Universal RecorderEDX-200A
→ 3-78
Sensor InterfacePCD-400A/430A
■Dimensions
LU-50KELU-100KELU-200KELU-500KELU-1TELU-2TELU-5TELU-10TELU-20TE
91.5
105108108167220277
77.5
909090
140190235
74
134130130144
172.5221
80
100100100112138186
50
80808095
120160
M5×8
M8×8M8×12M8×12M8×15M8×15M8×15
M8×1.25
M12×1.75M14×2M18×1.5M26×2M36×2M50×3
10
101010172027
12
192626365064
30
3050707070
100
3
766
101015
52
6254.554.562.5
78102.5
3.2 d=30
3.5 d=386 d=366 d=369 d=379 d=439 d=58
32.5
406060
100145190
A B (C) φD E F G H (K) SRφM O(L)φJModels
Connector plugPRC03-12A10-7M
LU-50 to 200KE
LU-500KE to 20TE
2-53
TRA
NSD
UC
ERS
2-53
Load Cells(Load Transducers)
Outline
Compressive
Tensile
Tensile &compressive
Component
Special
Other
LUH-FHigh-accuracy Tension/Compression Load Cell
Standard Accessories 4 hexagon socket head bolts M5, L=10 mm (30 mm with LUH-10TF and 20TF)1 hexagon bar (Opposite side 2.5 mm)
ZERO FLOAT
Zero float means such a phenomenon that a cycle of continuously applied tensile & compressive loads causes the zero to float. The value is expressed in percentage of the rated output. It is also called cyclic zero shift.
LUH-50KFLUH-100KFLUH-200KFLUH-500KFLUH-1TFLUH-2TFLUH-5TFLUH-10TFLUH-20TF
±500 N±1 kN±2 kN±5 kN
±10 kN±20 kN±50 kN
±100 kN±200 kN
1.4 kHz2.2 kHz3.1 kHz4.6 kHz4.2 kHz
6 kHz5.2 kHz4.5 kHz3.7 kHz
2.1 kg
4 kg
9 kg18 kg38 kg
Rated Capacity Natural Frequencies(Approx.)
Weight*(Approx.)Models
Excellent zero float characteristics Tension/Compression load cells
LUH-F series are tension/compression load cells featuring within ±0.02% RO nonlinearity. The hermetically-sealed structure with inert gas filled in ensures stable performance.
●Remote sensing available* (See page 9-14.)
da
×100 (% RO)
d
a
Zero Float=
OutputRated output
Rated capacity
Note: Arrow direction may be reverse.
Compressive load Tensile load
Safe Overloads 150%Natural Frequencies See table below.Weight See table below.Others Drop prevention stopper mountable *Customers have to prepare anti-dropping stoppers by themselves.Compliance Directive 2011/65/EU (RoHS)
Rated Capacity See table below.Nonlinearity Within ±0.02% ROHysteresis Within ±0.02% RORepeatability 0.02% RO or lessZero Float 0.02% RO or less (LUF-50KF to 500KF)Rated Output 2 mV/V ±0.1%
Safe Temperature -35 to 80°CCompensated Temperature -10 to 60°CTemperature Effect on Zero Within ±0.0015% RO/°CTemperature Effect on Output Within ±0.001%/°C
Safe Excitation 20 V AC or DC Recommended Excitation 1 to 10 V AC or DCInput Resistance 350 Ω ±0.5%Output Resistance 350 Ω ±0.5%Cable 6-conductor (0.5 mm2) chloroprene shielded cable, 9.5 mm diameter by 5 m long, bared at the tip (Shield wire is not connected to the case.)
●Nonlinearity: Within ±0.02% RO ●500 N to 200 kN
SpecificationsPerformance
Environmental Characteristics
Electrical Characteristics
Mechanical Properties
*Excluding cable* Customers have to prepare anti-dropping stoppers by themselves.
Saddle CA-B (Page 2-72)Mount base CF (Page 2-72)Movable saddle ER-B (Page 2-73)Ball joint TU (Page 2-75)
Optional Accessories
*Ball joint is required for tensile load measurement.
* To use the remote sensing function, use the recommended products for combination.
LUH-1 to 20TF
LUH-50 to 500KF
Bared at the tip(For remote sensing)
2-54
2-54
TRA
NSD
UC
ERS
Load Cells(Load Transducers)
Outline
Compressive
Tensile
Tensile &compressive
Component
Special
Other
①
②
③
④
φ38φ53
φ80φ100φ124φ148
154
4019
①
②
③
④
φ90φ108
φ80φ100φ124φ148
169
4035
4×φ7 at equal distance
4×φ13at equal distance
4×M8 at equal distance
4×φ13at equal distance
①
②
②
F
DC
B (A
pp
rox.
)A
(Ap
pro
x.)
G
φE
■Dimensions in combination with mount base
●In combination with saddle (CA) and mount base (CF) (LUH-50KF to 500KF)
●In combination with movable saddle (ER) and mount base (CF) (LUH-50KF to 2TF)
●In combination with ball joint (TU)
Note: Special accessories for tensile load measurement should be assembled at our factory.
① Load cell LUH-F② Saddle CA-2B③ Mount base CF-80④ Hexagon socket head bolt 4xM8, L=25 (Standard accessories of mount base)
① Load cell LUH-F② Movable saddle ER-2B③ Mount base CF-80 (1T, 2T)④ Hexagon socket head bolt 4xM8, L=25 (Standard accessories of mount base)
*From the viewpoint of guaranteed accuracy, allows neither a hook nor a shackle to be combined.
When using in combination with special accessories, consult with our sales engineer.
LUH-FRecommended
products for combination
●Dynamic measurement
→ 3-97
Instrumentation AmplifierWGA-710C
●Physical quantity indication
→ 3-9
Signal ConditionerCDV-900A
4×M8, d=15 φ80
(For mounting an anti-dropping stopper)
2×M5(90°position)
φ24SR40
A
44.5
φ98A
2×M5, 6 drilled, d=36 (90°position)
94B
B10
(8)
77
95
4×M8 d=15φ80 (89)
R3/4
U
φD
φV
φE2×M5(90°position) SR
J
□40
φC
J
GF
2×M5(P)
LH
BA
(N)
H K
M
4×Q
φV
R3/4
S
4×M8 T
■Dimensions
LUH-50KF to 500KF
LUH-1TF to 20TF
LUH-50KFLUH-100KFLUH-200KFLUH-500KF
LUH-1TFLUH-2TFLUH-5TFLUH-10TFLUH-20TF
M12, P=1.75
M18, P=1.5
M14, P=2 M18, P=1.5 M26, P=2 M36, P=2 M50, P=3
17
22
9595
127170228
7777
100135175
100100130160200
2424365068
2424365064
2020304050
3535506080
2222304565
4458
12
99
131723
1010172028
88
101525
6 drilled, d=36 6 drilled, d=36 9 drilled, d=42 9 drilled, d=54 9 drilled, d=65
M8, d=10 M10, d=10 M16, d=16 M20, d=15 M24, d=20
40406070
100
84.584.599.5
115.5135.5
d=12d=12d=15d=15d=15
24.524.5406080
808095
120160
A
A
B
B φC φD φE F G H J K L M (N) (P) Q SR S T U φV
Models
Models
LUH-50KFLUH-100KFLUH-200KFLUH-500KFLUH-1TFLUH-2TFLUH-5TF
TU-12
TU-18TU-14TU-18TU-26
M12 P=1.75
M18 P=1.5M14 P=2M18 P=1.5M26 P=2
207
231210231350
177
189173189280
85
110
16
23172337
12
18141825
30
42374270
②Ball Joints A B C D FφE G①Load Cells
2-55
TRA
NSD
UC
ERS
2-55
Load Cells(Load Transducers)
Outline
Compressive
Tensile
Tensile &compressive
Component
Special
Other
LUK-ATension/Compression Load Cell
Compact & lightweightTension/Compression load cells The thin structure is suitable for installation where the height is limited. The service life will be extended by using with one-half the rated capacity if repetitive loads are applied continuously.
To Ensure Safe UsageBe sure to prevent the shaft from turning
when using for hanging load measurement.
*When used for tension, make sure not to use special accessories such as ball-joint and rotating attachment.
The LUK-A is not applicable to setscrews.
Safe Overloads 150%Natural Frequencies See table.Weight See table.Safe Lateral Force Component See table.Safe Moments See table.Degree of Protection IP64 (IEC 60529)Compliance Directive 2011/65/EU (RoHS)
Safe Excitation 15 V AC or DC Recommended Excitation 1 to 10 V AC or DCInput Resistance 350 Ω ±1%Output Resistance 350 Ω ±1%Cable 4-conductor (0.3 mm2) chloroprene shielded cable, 7.6 mm diameter by 5 m long, terminated with a connector plug PRC03-12A10-7M (Shield wire is not connected to the case.)
Safe Temperature -35 to 80°CCompensated Temperature -10 to 70°CTemperature Effect on Zero Within ±0.005% RO/°CTemperature Effect on Output Within ±0.005%/°C
Rated Capacity See table below.Nonlinearity Within ±0.1% RO (500KN or larger: Within ±0.2% RO) Hysteresis Within ±0.1% RO (500KN or larger: Within ±0.2% RO) Repeatability 0.05% RO or less (500KN or larger: 0.1% RO or less) Rated Output 2 mV/V ±1% 5 to 20KN: 2.4 mV/V ±10%
●Thin ●5 kN to 2 MN
SpecificationsPerformance
Environmental Characteristics
Electrical Characteristics
Mechanical Properties
LUK-A-5KN to 20KN
LUK-A-50KN to 500KN
*TEDS-installed models are available. Inquiries are welcome.*Custom-made models with rated capacity over 2 MN are available. Inquiries are welcome.
2-56
2-56
TRA
NSD
UC
ERS
Load Cells(Load Transducers)
Outline
Compressive
Tensile
Tensile &compressive
Component
Special
Other
■Installation Example
Connector plugPRC03-12A10-7M
Shaft
Link
Screw
Smoothing hole
Load cell
Piston
φA
φB
φC
D
φ21
G
φC
φB
R1/2
8×φF (J )
φE
HH
φAφB
φC
HH
40G
φC
φB
D
8×φF (J )
R1/2
7025
φE
G
40
φA
φB
φC
HH
φC
φB
D
(J )16×φF
7025
R1/2
φE
LUK-A-5KN to 20KN LUK-A-50KN to 500KN LUK-A-1MN to 2MN
■Dimensions
LUK-ARecommended
products for combination
●Physical quantity indication
●Static measurement ●Dynamic measurement
→ 3-91 → 3-27
Data Logger UCAM-60 series
→ 3-5 → 3-63
Strain AmplifierDPM-900 series
Universal RecorderEDX-100A
Instrumentation AmplifierWGA-910A
→ 3-55
Universal RecorderEDX-200A
→ 3-78
Sensor InterfacePCD-400A/430A
*Excluding cable
LUK-A-5KNLUK-A-10KNLUK-A-20KNLUK-A-50KNLUK-A-100KNLUK-A-200KNLUK-A-500KNLUK-A-1MNLUK-A-2MN
±5 kN±10 kN±20 kN±50 kN
±100 kN±200 kN±500 kN
±1 MN±2 MN
15 N·m30 N·m60 N·m
150 N·m500 N·m
1 kN·m2.5 kN·m
5 kN·m10 kN·m
250 N500 N
1 kN2.5 kN
5 kN10 kN25 kN50 kN
100 kN
77
107127157227307375560
52
7077
100136200254410
20
34406090
138180260
62
8595
125180256314485
7
9131722262636
30
40506070
105150200
M12, P=1.75
M18, P=1.5M24, P=1.5M36, P=2M50, P=2M76, P=3M100, P=3M150, P=4
1
1222333
82
97102119157198233326
900 g
2 kg4 kg7 kg
18 kg50 kg90 kg
245 kg
Rated Capacity Safe Moments Safe Lateral Force
Component φA φB φC D φE φF G H (J) Weight*(Approx.)
Models
7.4 kHz10.8 kHz
8.5 kHz11 kHz
9 kHz7.5 kHz5.2 kHz
5 kHz3.9 kHz
NaturalFrequencies
(Approx.)
2-57
TRA
NSD
UC
ERS
2-57
Load Cells(Load Transducers)
Outline
Compressive
Tensile
Tensile &compressive
Component
Special
Other
LU-ASmall-capacity Tension/Compression Load Cell
*TEDS-installed models are available. Inquiries are welcome.
Small capacityHigh sensitivity Tension/Compression load cellsA straight beam is used as the diaphragm to enable highly accurate measurement of small loads.
LU-5KALU-10KALU-20KA
±50 N±100 N±200 N
200 Hz330 Hz500 Hz
Rated Capacity Natural Frequencies(Approx.)Models
■Dimensions ■Dimensions in combination with mount base
●In combination with mount base (CF-60)
Connector plugPRC03-12A10-7M
Safe Overloads 120%Natural Frequencies See table below.Weight Approx. 2.3 kg (Excluding cable)
Rated Capacity See table below.Nonlinearity Within ±0.3% RO Hysteresis Within ±0.2% RORepeatability 0.2% RO or lessRated Output 1.5 mV/V ±0.5%
Safe Temperature -20 to 75°CCompensated Temperature -10 to 65°CTemperature Effect on Zero Within ±0.01% RO/°CTemperature Effect on Output Within ±0.01%/°C
Safe Excitation 15 V AC or DCRecommended Excitation 1 to 10 V AC or DCInput Resistance 350 Ω ±0.5%Output Resistance 350 Ω ±0.5%Cable 4-conductor (0.3 mm2) chloroprene shielded cable, 7.6 mm diameter by 5 m long, terminated with a connector plug PRC03-12A10-7M (Shield wire is connected to the case.)
●Straight beam system ●50 to 200 N
SpecificationsPerformance
Environmental Characteristics
Electrical Characteristics
Mechanical Properties
M12×1.5 d=152×M3L=5 setscrew
SR11φ20
25
50 62
(77
.5)
φ60
φ90
(113)M12×1.5d=15
4×M6 d=7
φ90
LU-A
φ60
φ90
φ106
φ122
107.
5
Mount base CF-60
4×M6 L=20
Hexagon sockethead bolt
4×φ9at equaldistance
LU-ARecommended
products for combination
Hexagon socket head bolts for connection between load cells andmount bases are standard accessories of mount bases.
Mount base CF (Page 2-72)Optional Accessories
●Physical quantity indication
●Static measurement ●Dynamic measurement
→ 3-91 → 3-27
Data Logger UCAM-60 series
→ 3-5 → 3-63
Strain AmplifierDPM-900 series
Universal RecorderEDX-100A
Instrumentation AmplifierWGA-910A
→ 3-55
Universal RecorderEDX-200A
→ 3-78
Sensor InterfacePCD-400A/430A
2-66
2-66
TRA
NSD
UC
ERS
Load Cells(Load Transducers)
Outline
Compressive
Tensile
Tensile &compressive
Component
Special
Other
LUR-B-SA1 ●10 kN to 2 MN
Jack Load Cell
Special design for jacksModerate price Variety of capacity rangeLUR-B-SA1 series load cells are designed to measure loads applied to jacks when lifting up or moving a large machinery or structure in civil engineering and construction fields. These load cells enable the operators to prevent overloads, unbalanced loads, or movement of the center of gravity.
(Note) If the capacity is more than 200 kN, the calibration is performed for compressive load only.
■Dimensions
LUR-B-10KNSA1LUR-B-20KNSA1LUR-B-30KNSA1LUR-B-50KNSA1LUR-B-100KNSA1LUR-B-200KNSA1LUR-B-300KNSA1LUR-B-500KNSA1LUR-B-1MNSA1LUR-B-1.5MNSA1LUR-B-2MNSA1
±10 kN±20 kN±30 kN±50 kN
±100 kN±200 kN±300 kN±500 kN
±1 MN±1.5 MN
±2 MN
100110
125
175255255330430530590
7070
85
105125125170210250270
1520
20
35656580
110140160
2550
50
557090
120158200228
5560
60
6580
100130188220260
2046
46
5065-----
M12 P=1.75 d=15M18 P=1.5 d=20
M24 P=2 d=30
M39 P=2 d=45M50 P=2 d=65M65 P=3 d=65M85 P=3 d=85M110 P=3 d=118M140 P=4 d=140M160 P=4 d=170
1015
15
2540-----
1.4 kg2.1 kg
2.2 kg
2.5 kg5.2 kg
8 kg15 kg55 kg85 kg
100 kg
Rated Capacity A B (C) φD φE F G HWeight
(Approx.)Models
A
φD
HF F
(C)(C) B
H
G
φE
φE
Connector plugPRC03-12A10-7M
Safe Overloads 200%Weight See table below. (Excluding cable)
Rated Capacity See table below.Nonlinearity Within ±0.2% RO (300KNSA1 or larger: Within ±0.5% RO)Hysteresis Within ±0.1% RO (300KNSA1 or larger: Within ±0.5% RO)Rated Output 1 mV/V ±1%
Safe Temperature -10 to 60°CCompensated Temperature 0 to 60°CTemperature Effect on Zero Within ±0.01% RO/°CTemperature Effect on Output Within ±0.01%/°C
Safe Excitation 15 V AC or DCRecommended Excitation 1 to 12 V AC or DCInput Resistance 350 Ω ±2%Output Resistance 350 Ω ±2%Cable 4-conductor (0.3 mm2) chloroprene shielded cable, 7.6 mm diameter by 10 m long Sensor side: 1108-12A-10-7M Measuring instrument side: PRC03-12A10-7M
SpecificationsPerformance
Environmental Characteristics
Electrical Characteristics
Mechanical Properties
LUR-B-SA1Recommended
products for combination
●Physical quantity indication
●Static measurement ●Dynamic measurement
→ 3-91 → 3-27
Data Logger UCAM-60 series
→ 3-5 → 3-63
Strain AmplifierDPM-900 series
Universal RecorderEDX-100A
Instrumentation AmplifierWGA-910A
→ 3-55
Universal RecorderEDX-200A
→ 3-78
Sensor InterfacePCD-400A/430A