Commonwealth of Australia Gazette - · PDF fileStated Use: Transfer of liquefied petroleum gas (LPG) ... Outlet for liquids held in storage tanks : ... Stated Use: Used to apply chemical

Commonwealth of Australia Gazette

No. TC 07/45, Wednesday, 7 November 2007 Published by the Commonwealth of Australia

TARIFF CONCESSIONS

CONTENTS TCO Applications ....................................................................................................... 2 TCO Applications Withdrawn.................................................................................... 9 TCOs Made ............................................................................................................... 10 Local Manufacturer Initiated - TCO Revocation Requests .................................. 13 Section 273 Determinations Made.......................................................................... 14 Cheese Quota Transfers.......................................................................................... 15 TCOs Revoked – Unused for over 2 years ............................................................ 16

The Australian Customs Service (Customs) publishes the Commonwealth of Australia Tariff Concessions Gazette (the Tariff Concessions Gazette) free of

charge on the Customs internet site at: http://www.customs.gov.au Interested parties should select “media, publications and forms”, then “tariff

concessions gazette”. The gazettes are listed in date order and may be selected from the list of Adobe Portable Document Format (PDF) files.

General Inquiries: ..............................................................(02) 6275 6404

Facsimile: ...........................................................................(02) 6275 6376

Cat. No. ISSN 0813-8389 ©Commonwealth of Australia, 2007

http://www.customs.gov.au/

2 TCO Applications Commonwealth of Australia GazetteNo TC 07/45, Wednesday, 07 Nov 2007

TCO Applications

CUSTOMS ACT 1901 - NOTICE PURSUANT TO SECTION 269K(1) - APPLICATIONS MADE FOR TARIFF CONCESSION ORDERS

Applications have been lodged for Tariff Concession Orders for the goods described in the following TABLE.

Australian manufacturers who wish to contest the granting of a Tariff Concession Order for the goods described are invited to lodge a submission in writing in an approved form. Submissions must be lodged within 50 days of the date of publication of this Notice.

The operative date (Op.) and TC reference number follow the description of goods.

To assist local manufacturers, the use(s) to which the goods can be put follow the description of goods.

Submission forms are available from Custom Houses throughout Australia or on the Customs web site www.customs.gov.au.

For guidance on the required description style, phone 02 6275 6404, fax 02 6275 6376 or email [email protected].

THE TABLE

Description of Goods including the Schedule 4 Item Number Customs Tariff Classification General Duty Rate

3824.90.90 EMULSIFIERS, FOOD, being ANY of the following: (a) polyglycerol esters; (b) polyglycerol polyricinoleates; (c) fatty acid propylene glycol mono and diesters; (d) sorbitan esters, being mixtures of the partial esters of sorbitol and its mono- and dianhydrides with edible stearic acid; (e) sodium or calcium stearoyl lactylates Op. 08.10.07 - TC 0716959 Stated Use: Used as food additives Applicant: DANISCO AUSTRALIA PTY LTD

50

5%

4009.42.90 HOSES, LIQUEFIED PETROLEUM GAS (LPG), complying with Australia/New Zealand Standard AS/NZS 1869/1996 AND having BOTH of the following: (a) chloroprene covers; (b) collared fittings Op. 16.10.07 - TC 0717568 Stated Use: Transfer of liquefied petroleum gas (LPG) Applicant: ELGAS LTD

50

5%

6004.10.00 FABRICS, WARP KNIT, having ALL of the following: (a) NOT greater than 18% elastomeric fibre; (b) NOT greater than 82% nylon fibre; (c) weight NOT less than 180 g per square metre Op. 17.10.07 - TC 0717697 Stated Use: Used for the manufacture of garments, swimsuits, etc Applicant: STRETCHTEX INTERNATIONAL PTY LTD

50

7.5%

http://www.customs.gov.au/

mailto:[email protected]


Description of Goods including the Schedule 4 Item Number Customs Tariff Classification General Rate

6903.90.00 PARTS AND/OR ACCESSORIES, REFRACTORY AND FOUNDRY, MOLTEN METAL PLANT, being ANY of the following: (a) crucibles; (b) launders; (c) sheaths; (d) tubes; (e) bowls; (f) stoppers; (g) tools; (h) transporter shapes Op. 12.10.07 - TC 0717370 Stated Use: Used as metal contact foundry parts or accessories in the manufacture of ferrous and non-ferrous cast products Applicant: REFRACTORY AND CERAMIC PTY LTD

50

5%

7419.99.00 OUTLETS, TANK, brass, self tapping Op. 21.08.07 - TC 0712976 Stated Use: Outlet for liquids held in storage tanks Applicant: BELTRAMI GROUP UNIT TRUST

50

5%

8302.10.00 HINGES, DOOR, REFRIGERATED COOL ROOM Op. 16.10.07 - TC 0717641 Stated Use: For attaching to the doors of refrigerated cool rooms Applicant: ALLAN MARKETING GROUP PTY LTD.

50

5%

8306.10.00 BELLS, DOOR Op. 11.10.07 - TC 0717321 Stated Use: To alert people that somebody is at a door Applicant: ALLAN MARKETING GROUP PTY.LTD.

50

5%

8419.81.10 FOAMERS AND/OR DISPENSERS, HOT MILK Op. 11.10.07 - TC 0717308 Stated Use: Used for the preparation of hot milk based beverages Applicant: OSWALD AGENCIES PTY LTD

50

5%

8419.89.90 KILNS AND STEAM CONDITIONERS, THERMAL TREATMENT, HULLED OATS, having a processing capacity NOT less than 5 tonnes per hour Op. 12.10.07 - TC 0717343 Stated Use: Thermal treatment of hulled oats Applicant: UNIGRAIN PTY LTD

50

5%



8421.21.90 SOLIDS RECOVERY PLANT, CERAMIC GLAZE, controlled specific gravity and rheology, comprising ALL of the following: (a) pumps; (b) ceramic filter membranes; (c) wash train; (d) controllers Op. 27.09.07 - TC 0716853 Stated Use: Processing high-density and low-density over sprayed glaze used in sanitaryware production. Applicant: CAROMA INDUSTRIES LTD

50

5%

8421.39.00 GENERATORS, NITROGEN, PNEUMATIC TYRE INFLATION Op. 08.10.07 - TC 0716958 Stated Use: Inflation of pneumatic truck, bus and earthmover tyres with nitrogen Applicant: KALHIRE PTY.LTD.

50

5%

8421.39.00 SEPARATERS, NARURAL GAS PRODUCTION, comprising ALL of the following: (a) knock out drums; (b) knock out drum washers; (c) external maintenance platforms; (d) external access ladder structures Op. 15.10.07 - TC 0717418 Stated Use: The drying of natural gas during processing Applicant: BECHTEL AUSTRALIA PROPRIETARY LIMITED

50

5%

8428.90.00 BRIDGES, LIFTING, SUCTION, GLASS SHEETS Op. 12.10.07 - TC 0717414 Stated Use: Lifting glass sheets Applicant: G JAMES AUSTRALIA PTY.LTD.

50

5%



8431.49.90 PARTS, UNDERGROUND COAL LOADER, being ANY of the following: (a) z-bars; (b) swivels; (c) data plates; (d) booms; (e) boom locks; (f) power frames; (g) protection roofs; (h) brake pedal controls; (i) cylinders; (j) dump and hoists; (k) steering; (l) load frames; (m) sound suppressors; (n) brake coolers; (o) shims; (p) axles; (q) boom stands; (r) brakes; (s) controls; (t) up boxes; (u) frames; (v) plates; (w) panels; (x) weldments; (y) brackets; (z) supports Op. 18.10.07 - TC 0717854 Stated Use: Used in the manufacture of underground coal loaders Applicant: ANDERSON INDUSTRIES (AUST) PTY LTD

50

5%

8475.29.00 FLOAT GLASS PRODUCTION LINE, comprising ALL of the following: (a) batch processors; (b) melting furnaces; (c) float glass forming chambers; (d) annealing lehrs; (e) cold glass processors; (f) glass handlers; (g) cullet modules Op. 10.10.07 - TC 0717256 Stated Use: Used to manufacture flat glass Applicant: CSR BUILDING PRODUCTS LIMITED

50

5%

8479.89.90 COATERS, GLASS, CHEMICAL VAPOUR DEPOSITION, comprising ALL of the following: (a) tin compound feeders; (b) gas precursor feeders; (c) pollution controllers and processors; (d) hydrofluoric acid feeders; (e) beam coaters; (f) oil heaters and coolers Op. 10.10.07 - TC 0717248 Stated Use: Used to apply chemical coatings to glass Applicant: PILKINGTON AUSTRALIA ENGINEERING PTY LTD

50

5%



8502.31.90 GENERATORS AND DISTRIBUTORS, WIND POWERED, electric, having ALL the following: (a) AC/DC generators; (b) blades; (c) steel towers; (d) nacelles; (e) yaws; (f) hubs; (g) rotors; (h) sub-station switch gears; (i) cables; (j) foundation support rings; (k) controller and power modules; (l) lifts; (m) transformers Op. 02.10.07 - TC 0716568 Stated Use: Generating electricity using wind power Applicant: ACCIONA ENERGY OCEANIA PTY LTD

50

5%

8514.40.00 HEATERS, INDUCTION, PIZZA DELIVERY BAG Op. 10.10.07 - TC 0717301 Stated Use: Heater of pizza delivery bags by induction Applicant: J.L.LENNARD FOOD EQUIPMENT PTY LIMITED

50

5%

8515.19.90 SOLDERING MACHINES, XENON SOFTBEAM, programmable logic controlled, comprising ALL of the following: (a) visual inspection systems; (b) position torching systems; (c) xenon lamp units; (d) wire feeds Op. 15.10.07 - TC 0717428 Stated Use: Xenon softbeam soldering of components onto printed circuit boards Applicant: AUSTRALIAN AUTOMOTIVE AIR PTY.LTD.

50

5%

8518.29.90 SETS, MOTOR VEHICLE LOUDSPEAKER, comprising ALL of the following: (a) woofers; (b) tweeters: (c) audio crossovers Op. 12.10.07 - TC 0717369 Stated Use: Loudspeaker sets for mounting in motor vehicles Applicant: EASTCOAST DISTRIBUTORS PTY LTD

50

5%



8535.90.00 SUBSTATIONS, POWER, comprising ALL of the following: (a) air conditioners; (b) circuit breakers; (c) transformers; (d) controllers; (e) disconnecters; (f) generators; (g) meters; (h) cables; (i) reactors; (j) static variance compensators; (k) arrestors; (l) insulators; (m) steel supports; (n) battery banks; (o) chargers; (p) switches; (q) protection relays; (r) switchboards; (s) power line carrier; (t) capacitor banks; (u) counters; (v) busbars; (w) security modules; (x) footings; (y) communication modules Op. 11.10.07 - TC 0717269 Stated Use: The distribution of electrical power Applicant: QUEENSLAND ELECTRICITY TRANSMISSION CORPORATION

LIMITED

50

5%

8536.10.00 FUSE LINKS, having ALL of the following: (a) current rating NOT less than 2 A and NOT greater than 1 250 A; (b) breaking capacity of NOT less than 80 KA Op. 16.10.07 - TC 0717642 Stated Use: Used as safety devices which cuts the flow of current to prevent injury or damage to equipment Applicant: FLOWLINE INDUSTRIES PTY. LTD.

50

5%

8543.90.90 PARTS, TRANSMISSION POWER LINE, comprising ANY of the following: (a) insulators; (b) programmable logic controllers; (c) optical fibres; (d) conductors; (e) stringing sheaves; (f) steel supports; (g) fittings; (h) aluminium rings; (i) spacers; (j) dampers; (k) terminators; (l) power wires; (m) footings Op. 11.10.07 - TC 0717270 Stated Use: The transmission of electrical power Applicant: QUEENSLAND ELECTRICITY TRANSMISSION CORPORATION

LIMITED

50

5%



8704.22.00 TRUCKS, COMPRESSION IGNITION ENGINE, CAB CHASSIS, having BOTH of the following: (a) 4 x 2 wheel drives; (b) gross vehicle weight NOT less than 15 t and NOT greater than 17 t Op. 16.10.07 - TC 0717597 Stated Use: Used for transportation of goods Applicant: K MACNEVIN & CO PTY LTD

50

5%

8707.90.90 PARTS, ON-ROAD TRUCKS, HAVING A GROSS VEHICLE WEIGHT NOT LESS THAN 7.5 TONNES, being EITHER of the following: (a) truck cabs and/or cabins; (b) truck bodies Op. 17.10.07 - TC 0717752 Stated Use: Trucks cabs/cabins and bodies for on road trucks Applicant: WESTERN STAR TRUCKS AUSTRALIA PTY LTD

50

5%

8708.94.49 PARTS, ON-ROAD TRUCKS, HAVING A GROSS VEHICLE WEIGHT NOT LESS THAN 7.5 TONNES, being ANY of the following: (a) steering wheels; (b) steering columns; (c) steering boxes Op. 17.10.07 - TC 0717750 Stated Use: Steering wheels, steering columns and steering boxes for on-road trucks Applicant: WESTERN STAR TRUCKS AUSTRALIA PTY LTD

50

5%

9406.00.00 CABINS, PRESSURISED, HAZARDOUS CONDITIONS, having ALL of the following: (a) air conditioners; (b) flood lamps; (c) junction boxes; (d) winch control terminals; (e) grounding cables Op. 12.10.07 - TC 0717342 Stated Use: Specialised cabins for operations in hazardous conditions Applicant: SCHLUMBERGER OILFIELD AUSTRALIA PTY LIMITED

50

5%

9 TCO Applications Withdrawn Commonwealth of Australia GazetteNo TC 07/45, Wednesday, 07 Nov 2007

TCO Applications Withdrawn

CUSTOMS ACT 1901 - NOTICE PURSUANT TO SECTION 269G(3) - WITHDRAWAL OF A TARIFF CONCESSION ORDER APPLICATION

The Tariff Concession Order application set out in the following TABLE has been withdrawn by the applicant.

The number and date shown in the second column refers to the Gazette in which the application was notified.

THE TABLE

Description of Goods including the No. and Date Date of Customs Tariff Classification of Gazette Withdrawal

8479.89.90 COATING MACHINES, METAL SHEET, having BOTH of the following: a) in feed and out feed transporters; b) stainless steel basins Op. 17.09.07 - TC 0715096

TC 07/4003.10.07

30.10.07

10 TCOs Made Commonwealth of Australia GazetteNo TC 07/45, Wednesday, 07 Nov 2007

TCOs Made

CUSTOMS ACT 1901 - NOTICE PURSUANT TO SECTION 269R(1) - TARIFF CONCESSION ORDERS MADE

Tariff Concession Orders have been made for the goods described in the following TABLE.

The operative date (Op.) and TC reference No. follow the description of goods.

Local manufacturers of substitutable goods may request the revocation of TCOs at any time.

THE TABLE

Description of Goods including the Schedule 4 Item Number Customs Tariff Classification Last Date of Effect

3917.39.90 TUBING, AIR BRAKE, conforming to Society of Automotive Engineers (SAE) J844 standard, having ALL of the following: (a) polyamide cores; (b) synthetic reinforcement fibres; (c) polyamide outer sheaths Op. 13.08.07 Dec. date 29.10.07 - TC 0712821

50

3921.11.00 FOAM, PHENOLIC, WATER ABSORBENT Op. 24.08.07 Dec. date 02.11.07 - TC 0713580

50

3926.90.90 KITS, FALSE FINGERNAIL, consisting of ALL of the following: (a) false fingernails; (b) nail glue; (c) push pin; (d) manicure stick Op. 06.08.07 Dec. date 29.10.07 - TC 0712550

50

4811.90.90 PAPER, thermal imaging, having a weight NOT greater than 70 gsm and a width NOT less than 400 mm and a length NOT less than 5 000 metres Op. 03.08.07 Dec. date 29.10.07 - TC 0712493

50

6001.21.00 FABRICS, TERRY TOWELLING, knitted, having BOTH of the following: (a) weight NOT less than 400 gsm; (b) width NOT less than 1 450 mm Op. 16.08.07 Dec. date 02.11.07 - TC 0713093

50

6902.10.00 BRICKS AND/OR SHAPES, REFRACTORY, having ALL of the following: (a) magnesia (Mg0) content NOT less than 55%; (b) chromic oxide (Cr203) content NOT less than 15%; (c) silica (Si02) content NOT greater than 3% Op. 28.08.07 Dec. date 02.11.07 - TC 0713586

50

7306.29.00 PIPES, STEEL CASING, electric resistance welded(ERW), having ALL of the following: (a) diameter NOT less than 16 cm and NOT greater than 26 cm; (b) pipe threading; (c) coupled buttress connections complying with American Petroleum Institute (API) Specification 5CT standard Op. 23.08.07 Dec. date 02.11.07 - TC 0713418

50

7408.11.00 COPPER EXTRUSION, in coil form, extruded, annealed, solid rectangular cross-section whether or not including rounded edges or corners, having BOTH of the following: (a) thickness NOT less than 2 mm; (b) width NOT less than 15.5 mm Op. 16.08.07 Dec. date 02.11.07 - TC 0713009

50

8207.60.00 TOOLS, being oil and gas well casing reaming shoes Op. 22.08.07 Dec. date 02.11.07 - TC 0713255

50



8305.10.00 FITTINGS, LOOSE-LEAF BINDERS AND/OR FILES, being ANY of the following: (a) back plate rings; (b) lever arches; (c) back plates; (d) compressor bars; (e) finger rings; (f) slots; (g) clips Op. 22.08.07 Dec. date 02.11.07 - TC 0713411

50

8414.59.90 PARTS, MOTOR VEHICLE TESTING, CLIMATIC TEST CHAMBER, being wind tunnels Op. 17.08.07 Dec. date 02.11.07 - TC 0713122

50

8417.90.00 PARTS, GAS BURNER, being ANY of the following: (a) burner blocks; (b) burner tiles; (c) gas mixers Op. 21.08.07 Dec. date 29.10.07 - TC 0712979

50

8418.69.00 FREEZERS, VERTICAL PLATE, having ALL of the following: (a) coldest temperature range capacity to minus 35 degrees C; (b) ammonia refrigerants; (c) vertical top dischargers; (d) manual lever control valves Op. 22.08.07 Dec. date 02.11.07 - TC 0713424

50

8424.30.90 LINE, WHEEL CLEANING, TRUCK AND/OR TRAILER, water spray, sensor activated, drive through, having ALL of the following: (a) NOT less than 3 pump water wash delivery; (b) water delivery flow rate capacity NOT less than 5 000 l/m; (c) maximum cleaning length NOT less than 2 wheel revolutions; (d) solids settling under tank with integrated scraper-conveyor Op. 13.08.07 Dec. date 29.10.07 - TC 0712804

50

8438.10.90 LABORATORIES, TESTING BAKING, BISCUIT, comprising ALL of the following: (a) output capacity NOT greater than 10 kilos per hour; (b) rotary moulders; (c) four roller sheeters; (d) rotary cutters; (e) continuous band ovens having a belt width NOT greater than 120 mm Op. 17.08.07 Dec. date 29.10.07 - TC 0713094

50

8464.90.00 LINES, LAMINATED SAFETY GLASS PRODUCTION, having ALL of the following: (a) loaders; (b) washing and/or drying rooms; (c) film storage rooms; (d) heating zones; (e) offloaders Op. 16.08.07 Dec. date 29.10.07 - TC 0713090

50

8474.10.00 PLANT, WASHING, SAPPHIRES AND/OR TIN AND/OR GOLD, comprising ALL of the following: (a) hopper feeders; (b) trommels; (c) deslimers; (d) vibrating screen deck fine separators; (e) sapphire and/or gold and/or tin recoverers; (f) slurry handlers; (g) sapphire and/or gold cleaners; (h) generators Op. 21.08.07 Dec. date 29.10.07 - TC 0713236

50



8474.32.00 PLANT, ASPHALT, programmable logic controlled, comprising ALL of the following: (a) bins; (b) conveyor belts; (c) dryers; (d) batch towers; (e) hot elevators; (f) vibrating screens; (g) weigh hoppers; (h) plug mills; (i) electrically heated bitumen kettles; (j) baghouses; (k) baghouse dust silos; (l) dust elevators; (m) dust weigh hoppers; (n) lime or filler silos; (o) docket printers Op. 22.08.07 Dec. date 02.11.07 - TC 0713410

50

8479.89.90 LINE, ASSEMBLY, AUTOMOBILE AIRBAG, comprising ALL of the following: (a) cushion folders and sock inserters; (b) inflator brackets and gas guide crimpers; (c) cushions; (d) ramps; (e) washers; (f) bolt assemblers Op. 20.08.07 Dec. date 02.11.07 - TC 0713225

50

8503.00.00 PARTS, POWER GENERATOR, having a minimum capacity of NOT less than 200 MW, being ANY of the following: (a) air gap search coil probes; (b) coil end connection water boxes; (c) coil supports; (d) core laminates; (e) cover plates; (f) end winding bracings; (g) lock plates; (h) manifold clamps; (i) manifolds; (j) packing blocks; (k) phase ring blocks; (l) phase ring droppers; (m) phase rings; (n) rotor coils; (o) rotors; (p) search coils; (q) separators; (r) stator coils; (s) stators; (t) support rings; (u) taper slides; (v) wedges and fillers; (w) winding supports; (x) slot insulations Op. 28.08.07 Dec. date 02.11.07 - TC 0713613

50

8518.40.90 AMPLIFIERS, STEREO, ADDRESSABLE, HOME AUDIO ENTERTAINMENT SYSTEM Op. 27.08.07 Dec. date 02.11.07 - TC 0713588

50

8526.92.00 CONTROLLERS, REMOTE, RADIO FREQUENCY, MULTI-FUNCTION, HOME SOUND ENTERTAINMENT SYSTEM, incorporating an LCD current status display screen Op. 27.08.07 Dec. date 02.11.07 - TC 0713581

50

8537.10.90 PANELS, FASCIA CONTROL, MOTOR VEHICLE Op. 21.08.07 Dec. date 29.10.07 - TC 0712978

50

13 TCOs Made and Local Manufacturer Initiated - TCO Revocation Requests

Commonwealth of Australia GazetteNo TC 07/45, Wednesday, 07 Nov 2007


9001.90.30 LENSES, SAFETY GOGGLES, complying with Australian/New Zealand Standard 1337:1992 (AS/NZS 1337:1992) Op. 21.08.07 Dec. date 29.10.07 - TC 0712977

50

Local Manufacturer Initiated - TCO Revocation Requests

NOTIFICATION OF AN AUSTRALIAN INDUSTRY REVOCATION REQUEST - SECTION 269SC(1A) CUSTOMS ACT

Applications have been lodged for revocation of the Tariff Concession Orders set out in the following TABLE.

The Lodgement Request Date shown in the table below is the intended revocation date for the Tariff Concession Order which will take effect should the application for revocation be successful.

Importations not covered by in-transit provisions may be subject to post action as any decision to revoke an order is backdated to the date of request for revocation.

THE TABLE

Description of Goods including the Schedule 4 Item Number Customs Tariff Classification Lodgement Request Date

8705.90.00 SWEEPERS, STREET, SUCTION, having a minimum hopper capacity of NOT less than 3.6 m3 Op. 07.08.07 Dec. date 12.10.07 - TC 0712626

50 29.10.07

8705.90.00 SWEEPERS, STREET, SUCTION, having ALL of the following: (a) channel brushes; (b) nozzles; (c) sweep brushes; (d) minimum hopper capacity NOT less than 4 tonne; (e) dual sweep modules Op. 07.08.07 Dec. date 12.10.07 - TC 0712627

50 29.10.07

8705.90.00 SWEEPERS, PEDESTRIAN MALL AND STREET, SUCTION, having a minimum hopper capacity of NOT less than 1.5 m3 Op. 07.08.07 Dec. date 12.10.07 - TC 0712628

50 29.10.07

8707.90.90 ASSEMBLIES, SUCTION STREET SWEEPER, having ALL of the following: (a) ancillary engines; (b) channel brushes; (c) nozzles; (d) sweep brushes Op. 07.08.07 Dec. date 19.10.07 - TC 0712625

50 29.10.07

14 Section 273 Determinations Made Commonwealth of Australia GazetteNo TC 07/45, Wednesday, 07 Nov 2007

Section 273 Determinations Made

NOTICE OF DETERMINATIONS MADE UNDER PART XVI OF THE CUSTOMS ACT 1901

Under subsection 273B(2) of the Customs Act 1901, notice is hereby given of the making of determinations applying to goods of a kind specified in the table below.

In the table:

(i) the first column specifies the kind of goods to which the determination applies, any conditions specified in the determination, the commencement and cessation dates of the determination and the Determination reference number;

(ii) the second column specifies the item in Schedule 4 to the Customs Tariff Act 1995 that applies to the specified goods.

THE TABLE

Description of Goods Dates of Effect

Schedule 4 Item Number

Electric Motors for use in a water supply project 01.04.07 to 01.04.09 - AD 01001317

71

Tunnel Backfill Grouting System (Automatic Mixing Plant and Automatic Injection System) for use in a water supply project 01.04.07 to 01.04.09 - AD 01001318

71

Reverse Osmosis (RO) Seawater and Brackish Water Membranes for use in a water supply project 01.04.07 to 31.03.09 - AD 01001320

71

Submersible mixers for use in a water supply project 01.04.07 to 31.03.09 - AD 01001321

71

Pretreatment Gravity Filter Underdrain System inlcuding 18 filters for use in a water supply project 01.04.07 to 31.03.09 - AD 01001322

71

Seawater Intake Pumps for use in a water supply project 01.04.07 to 31.03.09 - AD 01001323

71

Tunnel Segment Gaskets (TSG) including glueing system for use in a water supply project 01.04.07 to 31.03.09 - AD 01001324

71

Stainless steel bar including stainless steel tube, stainless steel wire and strip stainless steel for use in a water project. 01.05.07 to 30.04.09 - AD 01001327

71

Components of heat exchangers for a smelter project 15.06.06 to 14.06.08 - AD 01001390

71

Ethylene glycol for use in PET resin. 11.10.07 to 10.10.09 - AD 01001401

57

15 Cheese Quota Transfers Commonwealth of Australia GazetteNo TC 07/43, Wednesday, 7 Nov 2007

Cheese Quota Transfers

AUSTRALIAN CUSTOMS SERVICE

TARIFF QUOTAS - QUOTA TRANSACTIONS PROCESSED IN THE PERIOD 29 Oct 2007 to 05 Nov 2007.

GENERAL INFORMATION

This Gazette contains details of quota transactions processed in the period 29 Oct 2007 to 05 Nov 2007 inclusive.

Part 1 contains a Table specifying quota category details.

Part 2 lists all adjustments to previous allocations which have been caused by transfer transactions.

NB.- In Part 2, transactions represent changes to individual tariff quotas and do not necessarily represent the entire holdings in that category for the quota holder.

- The "AS WAS" and "AS IS" columns indicate the quota levels for that particular tariff quota only at the time of that transaction.

- The amount of the transaction can be deduced by subtracting the "AS WAS" column from the "AS IS" column.

Inquiries concerning any information published within this Gazette should be directed to the Trade Branch, Australian Customs Service, Customs House, 5 Constitution Avenue, Canberra City, ACT, 2601.

PART 1

In pursuance of Section 273B of the Customs Act 1901, notice is hereby given that a Determination specified in Part 2 amended a previous Determination by deleting the figures in the column headed “QUANTITY AS WAS" and inserting the figures in the column headed "QUANTITY AS IS".

THE TABLE

CATEGORY CODE

UNIT QUANTITY

QUOTA ITEM NUMBER

QUOTA DESCRIPTION

311 Kilograms 61A Cheese & Curd

PART 2

AMENDED ALLOCATIONS

CAT CODE

QUOTA HOLDERS LEGAL NAME POST CODE

QUANTITY (KG) AS WAS

QUANTITY (KG) AS IS

DETERMINATION NUMBER

311 PERCIVIAL D HARRISON & MARIE L PACKER 3078 37,883.00 0.00 000186

311 MENORA GOURMET PRODUCTS UNIT TRUST 3171 0.00 37,883.00 000186

16 TCOs Revoked - Unused for over 2 years Commonwealth of Australia GazetteNo TC 07/43, Wednesday, 7 Nov 2007

TCOs Revoked – Unused for over 2 years CUSTOMS ACT 1901

NOTICE PURSUANT TO SECTION 269SE(2) - TARIFF CONCESSION ORDER REVOCATION AT THE INITIATIVE OF CUSTOMS

The Tariff Concession Orders listed in THE TABLE below have not been used for at least 2 years and have been revoked under Section 269SD(1A). In transit provisions apply.

THE TABLE


2915.90 VINYL ESTERS, being synthetic saturated monocarboxylic acid mixtures of highly branched C 10 isomers Op. 08.04.88 Dec. date 09.06.88 - TC 8803582 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

2917.39 DIBASIC LEAD PHTHALATE Op. 15.08.89 Dec. date 20.02.90 - TC 8906737 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

2917.39 METHYL TETRAHYDROPHTHALIC ANHYDRIDE Op. 11.01.90 Dec. date 12.04.90 - TC 9001402 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

2921.11.00 MONOMETHYLAMINE NITRATE IN AQUEOUS SOLUTION Op. 07.07.94 Dec. date 07.10.94 - TC 9406016 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

3005.90.90 WOUND DRESSINGS, non-adhesive, having ALL of the following: (a) transparent film backing; (b) polyurethane membrane matrix; (c) moisture activated wound cleanser; (d) glycerin moisturiser; (e) absorbent starch co-polymer Op. 11.01.00 Dec. date 24.03.00 - TC 0000598 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

3204.17.00 PIGMENT RED 5, C.I. No. 12490, Bon Arylamide Carmine FB, but NOT including preparations based thereon Op. 05.03.93 Dec. date 18.06.93 - TC 9308665 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

3204.17.00 PIGMENT RED 184, C.I. No. 12487, Monoazo Red, but NOT including preparations based thereon Op. 05.03.93 Dec. date 18.06.93 - TC 9308668 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

3207.20 ENAMELS, vitreous, jewellers" grade Op. 08.11.83 Dec. date 08.11.83 - TC 8340030 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

3208.90.00 METHYL SILOXANE POLYMER SOLUTION Op. 14.08.01 Dec. date 26.10.01 - TC 0107096 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



3405.90.00 METAL POLISH IMPREGNATED WADDING, containing surface active substances, capable of polishing oxidised aluminium surfaces Op. 24.03.94 Dec. date 01.07.94 - TC 9403795 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

3506.91.00 LOCKING COMPOUND, ANAEROBIC, METHACRYLATE Op. 14.12.99 Dec. date 03.03.00 - TC 9910037 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

3603.00.00 DETONATORS, electric, having BOTH of the following: (a) a nominated pyrotechnic delay within the range 0 MS to 480 MS; (b) a maximum deviation of firing time from nominated delay of +/- 3% Op. 02.02.96 Dec. date 24.05.96 - TC 9602669 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

3703.10 PAPER, photosensitive, silver halide, colour reversal, positive to positive colour printing, in sheets or rolls, emulsion coated on a resin coated base Op. 15.06.89 Dec. date 19.10.89 - TC 8904735 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

3812.30.00 OCTYLATED DIPHENYLAMINE, BUTYLATED Op. 07.08.98 Dec. date 07.08.98 - TC 9806757 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

3816.00.00 MORTAR, refractory, heat-setting bonded containing by weight ALL of the following: (a) alumina not less than 56%; (b) zirconia not less than 25%; (c) silica not less than 12% Op. 03.06.93 Dec. date 10.09.93 - TC 9305155 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

3816.00.00 GUNNING MIX, REFRACTORY, consisting of ALL of the following: (a) silicon carbide NOT less than 20% and NOT greater than 50%; (b) graphite NOT less than 20% and NOT greater than 50%; (c) barium sulphate NOT less than 10% and NOT greater than 20%; (d) magnesium oxide NOT less than 2.5% and NOT greater than 5%; (e) quartz (Si02) NOT greater than 3% Op. 27.10.04 Dec. date 11.03.05 - TC 0411190 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

3824.90 MIXTURES of toluene substituted with monobenzyle and dibenzyl groups stabilised with an antioxidant having ALL of the following electrical properties: PROPERTY MEAN VALUE UNIT TEST METHOD dielectric constant 2.66 - IEC 247 at 25 degrees C dielectric losses < 0.004 - IEC 247 50 Hz-100 degrees C volume resistivity > 900 G.Ohms Ohm x cm IEC 247 100 degrees C breakdown voltage > 70 kV 25 degrees C VDE electrodes - 2 mm gap H2 absorption 2.3 cu cm/h PIRELLI Op. 01.07.96 Dec. date 11.07.96 - TC 9603474 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



3824.90 ALKYLKETENE DIMER Op. 01.07.96 Dec. date 18.06.96 - TC 9603514 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

3824.90 THICKENING AND BINDING AGENTS, composed of bio-degradable binder, thickening agent and surfacants, being glazing additives for ceramics and sanitary ware Op. 01.07.96 Dec. date 17.06.96 - TC 9603521 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

3824.90 CURING AGENTS, epoxy resin, having a basis of dicyandiamide Op. 01.07.96 Dec. date 18.06.96 - TC 9603594 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

3824.90 VULCANISING AGENTS, being 80% sulphur bound in a polymer blend of ethylene propylene diene monomer (EPDM) and ethylene vinyl acetate (EVA) Op. 01.07.96 Dec. date 17.06.96 - TC 9603602 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

3824.90.90 ANTI CORROSIVE ADDITIVE, having ALL of the following: (a) phosphoric acid mono ester; (b) benzotriabole; (c) diethanol amine; (d) acetylene based surfactant (non-ionic) Op. 01.07.96 Dec. date 09.07.96 - TC 9604048 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

3824.90.90 PROTECTIVE COATING MIXTURE, containing ALL of the following: (a) dipropylene glycol; (b) carbon; (c) non-ionic surface active agent; (d) zinc flake; (e) zinc potassium chromate; (f) mica; (g) aluminium phosphate Op. 01.07.96 Dec. date 09.07.96 - TC 9604052 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

3824.90.90 TERTIARY - BUTYL PEROXYACETATE, as a 50% W/W solution in mineral spirits with an active oxygen content (percent by weight) of 5.93 - 6.18 Op. 01.07.96 Dec. date 12.06.96 - TC 9605938 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

3824.90.90 CROSSLINKING AGENTS, polyolefins and elastomers, containing NOT less than 35% organo silanes Op. 01.07.96 Dec. date 23.08.96 - TC 9609998 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

3824.90.90 AZODICARBONAMIDE, MODIFIED Op. 04.06.98 Dec. date 07.08.98 - TC 9804834 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

3824.90.90 TETRAETHYLAMMONIUM TETRAFLUOROBORATE SALT (CAS #429-06-1), dissolved and/or dispersed in acetonitrile (CAS #75-05-8), (<30% TEABF4) Op. 06.03.03 Dec. date 02.06.03 - TC 0302438 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



3904.10.00 POLYVINYL CHLORIDE RESIN, partially cross-linked, containing between 20% and 26% tetrahydrofuran-insoluble material Op. 02.03.93 Dec. date 04.06.93 - TC 9308621 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

3906.90 OCTYLACRYLAMIDE-ACRYLATES-BUTYLAMINOETHYL METHACRYLATES OR OCTYL ACRYLAMIDE-ACRYLATES-POLYMERS, being ethanol or propanol soluble when partially or fully neutralised with 2-amino-2-methyl-1- propanol, NOT being water dispersible or soluble in the form as imported Op. 05.03.90 Dec. date 07.06.90 - TC 9002872 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

3906.90.00 ACRYLIC OLIGOMER, diluted with 37% by weight of isobornyl acrylate monomer Op. 18.01.95 Dec. date 21.04.95 - TC 9500993 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

3907.20 POLYETHYLENE OXIDE in granular form, containing NOT less than 30% + or - 5% by weight of fluorocarbon elastomer Op. 16.01.91 Dec. date 10.04.91 - TC 9101469 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

3909.50.10 POLYURETHANE FOAM, single component, moisture-curing, in aerosol cans of less than one litre, and using a non-flammable propellant mixture Op. 12.02.93 Dec. date 21.05.93 - TC 9308275 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

3910.00.00 COPOLYMER, of polydimethylsiloxane and poly-methyl-alkyl/aryl siloxane, containing less than 50 mole % of dimethylsiloxane and having alkyl/aryl groups of C6 or higher carbon number - 95% or more Op. 26.04.93 Dec. date 30.07.93 - TC 9305375 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

3917.39.90 PLASTIC TUBING, waste water samplers Op. 06.09.94 Dec. date 01.02.95 - TC 9407365 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

3918.10.00 PANEL, PVC, crosslinked, stabilised and flexible, thickness less than 0.15 mm, with rigid PVC extrusions welded to full perimeter Op. 13.02.95 Dec. date 13.07.95 - TC 9501674 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

3918.90.00 PLANKS AND TILES, 6.5 mm thick, wooden fibre core, covered with high pressure laminates, incorporating tongue and groove system, but NOT including vinyl sheets OR tiles Op. 27.05.94 Dec. date 17.10.94 - TC 9404903 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



3919.10 TAPE, leader splicing, translucent polyester, having ALL of the following: (a) pressure sensitive silicone adhesive coated on one side; (b) total tape thickness of 3.5 mils (0.0889 mm); (c) width NOT less than 12.00 mm but NOT exceeding 50.80 mm; (d) non permanent adhesion ability; (e) leaves no residue upon separation Op. 22.11.91 Dec. date 25.03.92 - TC 9110178 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

3919.90 PLATES, SHEETS, FILM, FOIL OR STRIP, cellulose acetate or cellulose nitrate graphic arts Op. 21.12.87 Dec. date 25.10.88 - TC 8736079 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

3919.90.00 POLYVINYL FLUORIDE, having ALL of the following: (a) coated with a pressure sensitive adhesive; (b) laminated to a release liner; (c) a transmission of less than 25% of UV light to 380 nanometers measured by UV visible spectrometer on film Op. 26.05.93 Dec. date 27.08.93 - TC 9305019 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

3919.90.00 TAPE, cast, polyvinyl chloride foam, self adhesive, self wound, manufactured with a silicon coated paper release liner on the non adhesive side of the foam, having ALL of the following: (a) width 1000 mm or greater; (b) UV, ozone, oxidation and fungi resistant; (c) backing material, polyvinyl chloride closed cell foam; (d) adhesive type; acrylic; (e) adhesive power; 7N/25mm; (f) nominal density (ASTM D-1667), 100kgs/m3; (g) hardness - shore 00 (ASTM D-2240), 20; (h) force to compress 25% (ASTM D-1667), 0.155kgs/cm2; (i) compression set 30% (% loss from original height - ASTM D 1667), 5%; (j) water tightness: 100% at 50% compression; (k) water absorption (vol % - MTP), 1.2%; (l) tensile strength (ASTM D-412), 1.54kgs/cm2; (m) elongation at break (ASTM D-412), 140%; (n) thermal conductivity (sq.ft(hr) DEG F - ASTM C-518), 0.26btu/in; (o) temperature resistance, 40 to 80 (DEG C) service temp; (p) standard tape thickness, from 3.2mm to 12.7mm both inclusive but not including any goods which are manufactured with a release liner on the adhesive side Op. 10.02.95 Dec. date 12.05.95 - TC 9501559 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

3920.20.00 POLYPROPYLENE FILM, cast, having ALL of the following features: (a) width range of 10mm to 20mm inclusive; (b) cast thickness 19.05 microns (+ or - 2.03 microns); (c) embossed thickness 44.45 microns (+ or - 10.16 microns); (d) step wound onto a 152.40 mm core Op. 16.06.95 Dec. date 22.09.95 - TC 9508305 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



3920.30 POLYSTYRENE FILM, having BOTH of the following: (a) nominal thickness of 23, 25, 30 or 50 microns; (b) on reels having a nominal ID of 203 mm Op. 07.03.88 Dec. date 14.08.89 - TC 8903768 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

3920.59 SHEETING, radiation shielding, transparent, of an acrylic/lead material manufactured by the chemical introduction of lead into the resin by co-polymerisation Op. 19.09.86 Dec. date 19.09.86 - TC 8635897 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

3921.14.00 REGENERATED CELLULOSE VEGETAL MATERIAL, absorbent, in planar forms Op. 06.05.94 Dec. date 12.08.94 - TC 9404580 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

3921.90 GLASS FIBRE FABRIC, woven, coated with polyester resin, having ALL of the following: (a) a thermal rating of 180 degrees C or greater based on ASTM D-1830 Curved Electrode Test; (b) a dielectric strength exceeding 850 V/mil based on ASTM D-902 Test Method; (c) a width exceeding 102 mm Op. 13.05.86 Dec. date 19.06.87 - TC 8633730 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

3921.90.90 MASTERING FILM, in rolls for computerised, digital copier/printers Op. 11.02.93 Dec. date 28.05.93 - TC 9308270 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

3923.40.00 DYE TUBES, axially flexible, having ALL of the following: (a) protected transfer tail; (b) compression greater than 10%; (c) compatible with 50 mm outside diameter dye spindles Op. 22.04.94 Dec. date 29.07.94 - TC 9404319 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

3923.50.00 CAPS, fitment, having ALL of the following: (a) rectangle rim; (b) lid assembly, reclosable; (c) length 47 mm (+ or - 10%); (d) width 25 mm (+ or - 10%); (e) applied by hot melt to package Op. 09.10.95 Dec. date 12.01.96 - TC 9511144 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

3926.90 INLETS, filling, water bed bladder, incorporating a plug and safety cap Op. 07.02.84 Dec. date 07.02.84 - TC 8340127 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

3926.90 SPRINGS, connecting rod, shaker conveyor, epoxy fibreglass Op. 08.11.83 Dec. date 08.11.83 - TC 8341214 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

3926.90 TAXIDERMISTS" SUPPLIES, being artificial antlers, ear liners, heads or body forms Op. 03.10.85 Dec. date 30.12.85 - TC 8534553 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



3926.90 WIRE, pintle, polyester with stainless steel path finder Op. 21.02.86 Dec. date 23.04.86 - TC 8632384 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

3926.90 LIGHT TRAPS, capable of restricting the passage of light whilst allowing full ventilation flow when installed in front of ventilation fans Op. 24.11.86 Dec. date 01.05.87 - TC 8636258 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

3926.90.90 CONNNECTION BOX, polystyrene, quick connect cable distribution system Op. 25.06.93 Dec. date 01.10.93 - TC 9304675 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

3926.90.90 SPRING ENERGISED SEALS, made from polytetrafluoroethylene (PTFE) compounds,including rod seals, shaft seals and static face seals Op. 02.02.94 Dec. date 06.05.94 - TC 9402131 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

3926.90.90 HANDLES, switch rotary cam, incorporating a steel fixing screw Op. 14.11.94 Dec. date 03.03.95 - TC 9408903 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

3926.90.90 YARN, FIBREGLASS, multifilament, PVC coated Op. 26.02.02 Dec. date 13.07.04 - TC 0406971 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

4002.19 SYNTHETIC RUBBER OF POLYBUTADIENE-STYRENE COPOLYMER, produced by the hot polymerisation method, with a nominal bound styrene content in the range of 42% to 50% (both inclusive), determined by the use of the Test Method specified in ASTM D1416 Op. 01.09.83 Dec. date 01.09.83 - TC 8333808 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

4002.99 TAPE, printing plate mounting, styrene-butadiene foam, having ALL of the following: (a) width NOT less than 300 mm; (b) thickness 0.38 mm or greater but NOT exceeding 0.55 mm; (c) coated on one side with synthetic rubber adhesive, and the other side with synthetic rubber or acrylic adhesive Op. 26.08.91 Dec. date 11.11.91 - TC 9107730 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

4008.21 RUBBER, in coil form, complying to ASTM Specifications D2000-2CH, 615, A25, B14, E15, E35, F17, Z1 and having ALL of the following: (a) length 10 m or greater; (b) width 74 mm or greater but NOT exceeding 76 mm; (c) thickness 1.27 mm or greater but NOT exceeding 1.52 mm For the purposes of TC 8534961 Z1 = coolant immersion for 168 h at 100 degrees C Op. 11.11.85 Dec. date 05.02.86 - TC 8534961 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



4009.21.90 HOSE, seamless, elastomeric rubber tube and elastomeric rubber cover, having ALL of the following specifications: (a) working pressure of 17.2 MPa or greater but NOT exceeding 19.0 MPa; (b) burst pressure of 68.9 MPa or greater but NOT exceeding 75.8 MPa; (c) able to withstand water operating temperatures NOT exceeding 107 degrees C Op. 01.01.02 Dec. date 03.01.02 - TC 0105454 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

4009.42.90 HOSES, OIL, complying with Oil Companies International Marine Forum (OCIMF) Standard, having ALL the following: (a) length NOT less than 6 metres; (b) flexible steel wire reinforcement; (c) pressure rating NOT less than 15 bar; (d) bore NOT less than 40 mm; (e) polyurethane outer carcass; (f) galvanised end fittings Op. 26.03.03 Dec. date 20.06.03 - TC 0303228 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

4011.94.00 TYRES, pneumatic as follows: (a) TRA code E2 or L2 size 17.5 in x 25 in (44.5 cm x 63.5 cm); OR (b) TRA code E3 or L3 size 17.5 in x 25 in (44.5 cm x 63.5 cm) Op. 01.01.02 Dec. date 09.01.02 - TC 0107631 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

4014.90 ENEMAS OR DOUBLE BELLOWS OR POWDER BLOWERS Op. 25.10.83 Dec. date 25.10.83 - TC 8340569 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

4016.10.00 TYRE LINERS, having ANY of the following specifications: TYRE SIZE RIM SIZE (a) 4.00/4.80-8 2.50 (b) 4.00/4.80-8 3.00 (c) 4.00/4.80-8 3.50 (d) 4.00/4.80-8 3.75 (e) 5.00/5.80-8 3.00 (f) 5.00/5.80-8 3.25 (g) 5.00/5.80-8 3.75 (h) 6.00/6.90-9 4.00 (i) 6.50-10 5.00 (j) 7.00-12 5.00 (k) 7.00-15 5.50 (l) 7.00-15 6.00 (m) 7.50-15 5.00 (n) 7.50-15 5.50 (o) 7.50-15 6.00 (p) 7.50-15 6.50 (q) 815-15/28x9-15 7.00 (r) 825-15 6.50 (s) 825-15 7.00 (t) 28x12.5-15 9.75 (u) 32x12.1-15 9.75 (v) 35x15 11.00 (w) 36x11-15 6.50 (x) 36x11-15 7.00 (y) 38x16-15 11.50 (z) 10.00-15 6.50 (aa) 10.00-15 7.00 (ab) 10.00-15 7.50 (ac) 14.50-15 10.00 (ad) 14.50-15 11.00 (Continued on next page)

50 31.10.07



(Continued from previous page) (ae) 8.25-20 6.00 (af) 8.25-20 6.50 (ag) 9.00-20 6.50 (ah) 9.00-20 7.00 (ai) 9.00-20 7.50 (aj) 10.00-20 7.33 (ak) 10.00-20 7.50 (al) 10.00-20 8.00 (am) 12.00-20 7.00/7.50 (an) 12.00-20 7.33/7.50 (ao) 12.00-20 7.33 (ap) 12.00-20 7.50 (aq) 12.00-20 8.00 (ar) 12.00-20 8.00/8.50 (as) 12.00-20 8.50 (at) 14.00-20 10.00 (au) 11.00-22 7.50 (av) 44x18-20 15.00 (aw) 12.00-24 8.50 (ax) 14.00-24 10.00 (ay) 14.00-25 11.25 (az) 16.00-25 11.25 (ba) 16x6-8 4.33 (bb) 18x7-8 4.33 (bc) 180/70-8 4.33 (bd) 225/75-10 6.50 (be) 225/75-15 7.00 (bf) 250/60-12 8.00 (bg) 250/75-12 8.00 (bh) 250-15 7.00 (bi) 250-15 7.50 (bj) 250-15 8.00 (bk) 250/70-15 7.00/7.50 (bl) 300-15 8.00 (bm) 315/70-15 8.00 (bn) 315/70-15 9.75 (bo) 10-16.5 8.25 (bp) 12-16.5 9.75 (bq) 125/70-8 3.25 (br) 125/75-8 3.00 (bs) 150/75-8 4.33 (bt) 200/75-9 6.00 (bu) 205/75-15 6.50 (bv) 215/85-16 6.50 (bw) 10-15 8.25 (bx) 12-15 9.75 (by) 37x12.50-16.5 8.25 (bz) 355/65-15 9.75 (ca) 13/70-18 8.00 (cb) 9.00-10 7.00 (cc) 44-18Lx20 13.25 (cd) 7.50-16 5.50 (ce) 18.00-25 13.25 (cf) 17.5-25 14.00 (cg) 27x8.50-15 6.00 (ch) 18x9.50-8 7.00 (ci) 23x8.50-12 7.00 (cj) 21x8-9 6.00 (ck) 20.5-25 17.00 (cl) 49x17-20 14.00 (cm) 15.5x25 12.00 (cn) 18.5x8.5-8 7.00 (co) 50x20-20 15.00 (cp) 570-12 5.00 (cq) 570-12 7.00 (cr) 570x8/6 3.75 (cs) 6.50-10 5.50 Op. 21.10.97 Dec. date 09.01.98 - TC 9709297 Revoked 2 years non-use. In transit provisions apply



4016.99 BANDS, rubber, length 80 mm or greater but NOT exceeding 100 mm and width 1.9 mm or greater but NOT exceeding 2.9 mm Op. 27.09.83 Dec. date 27.09.83 - TC 8334543 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

4016.99 PROTECTORS, tyre, unhardened rubber, fabric reinforced Op. 17.02.86 Dec. date 16.05.86 - TC 8632565 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

4016.99 BAND ASSEMBLIES, rubber stamp type, bearing numerals and characters, having internal "loop" diameters of 35.5 mm, 40.35 mm, 71.5 mm, 107.5 mm, 111.5 mm and 121.5 mm Op. 23.05.91 Dec. date 07.08.91 - TC 9104849 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

4016.99.00 SPRINGS, AIR, having ALL of the following: (a) load range NOT less than 1 000 kg but NOT exceeding 5 500 kg; (b) operating pressure NOT less than 100 kPa but NOT exceeding 690 kPa; (c) height range NOT less than 20 cm but NOT exceeding 90 cm; (d) non detachable top plate with fittings for attachment of suspension and air supply; (e) rubber flex member (bellows) permanently attached to the top plate; (f) non detachable assembly attached to bottom of flex member with or without a piston assembly Op. 30.07.97 Dec. date 10.10.97 - TC 9706649 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

4421.90.00 BOARDS OF AMERICAN OAK, oblong sections approximately 1.00 m x 10 cm x 12 mm with 2 holes drilled approximately 800 mm centre, toasted over oakwood fire Op. 19.01.96 Dec. date 30.04.96 - TC 9601974 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

4811.51.00 PAPERBOARD, bleached, in rolls, having ALL the following: (a) polyester coating on one side with a weight NOT greater than 48 gsm; (b) total weight 300 gsm to 500 gsm (inclusive); (c) caliper 0.18 mm to 0.70 mm (inclusive); (d) GE brightness level NOT less than 77%; (e) stiffness: machine direction (MD) greater than 160, cross direction (CD) greater than 80 using the Taber V-5 test method Op. 01.01.02 Dec. date 09.01.02 - TC 0107595 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

4811.90.90 PAPER, BONDED FELT, impregnated with synthetic rubber Op. 23.01.98 Dec. date 24.04.98 - TC 9800695 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



4823.90 PAPERBOARD, embossing, consisting of layers of ALL of the following: (a) polyethylene; (b) rubber coated fabric; (c) cardboard; (d) adhesive coated polyvinyl chloride; (e) polyvinyl chloride Op. 28.01.87 Dec. date 05.06.87 - TC 8732310 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

4907.00.90 TRAVELLERS CHEQUES issued in ANY of the following currencies: (a) Dutch Guilder; (b) Spanish Peseta; (c) European Currency Unit Op. 07.02.94 Dec. date 25.05.94 - TC 9402177 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

4907.00.90 TRAVELLERS CHEQUES, issued in Australian currency Op. 24.05.96 Dec. date 23.08.96 - TC 9607875 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

4911.99.00 COLLECTOR CARDS, being stickers, for retail sale Op. 03.06.94 Dec. date 21.09.94 - TC 9405010 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

4911.99.00 COLLECTOR DISCS OR TAGS, depicting cartoon characters, printed both sides, diameter NOT exceeding 5 cm, with OR without stickers and/or collector cards Op. 14.06.02 Dec. date 30.08.02 - TC 0205136 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

5205.44.00 SEWING THREAD, cotton, multiple ply, single "s" fold with final "z" twist Op. 14.06.95 Dec. date 29.09.95 - TC 9508195 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

5402.32.00 YARN, multifilament, manufactured from high tenacity synthetic polyamide filament yarns, air textured (bulked), having ALL of the following characteristics: (a) a tenacity of NOT less than 32 cN/tex; and, (b) in ANY of the following count ranges: (i) 1 000 decitex to 1 200 decitex (inclusive)/ 140 filaments, each with a count range of 7.1 decitex to 8.6 decitex (inclusive); (ii) 1 000 decitex to 1 200 decitex (inclusive)/ 280 filaments, each with a count range of 3.5 decitex to 4.3 decitex (inclusive); (iii) 500 decitex to 600 decitex (inclusive)/ 140 filaments, each with a count range of 3.5 decitex to 4.3 decitex (inclusive) Op. 20.03.96 Dec. date 11.07.96 - TC 9604837 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



5402.33.00 YARN, polyester, comprised of polyester filament core yarn, polyester filament knot textured yarn, polyester filament pressing yarn and having the following number of twists per metre: (a) 1 029 first twist; (b) 470 reverse twist Op. 08.12.95 Dec. date 25.03.96 - TC 9600091 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

5402.33.00 YARN, 100% continuous filament semi dull polyester, flame retardent, having ALL of the following: (a) 2/167 decitex (150 denier) filament; (b) filament count 48 to 50; (c) raw white Op. 19.03.01 Dec. date 01.06.01 - TC 0102373 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

5402.59.00 YARN, polypropylene, continuous multi-filament, UV stability greater than 250 KLY (Kilo Langley or KCAL/sq cm), tangled OR twisted, having a decitex between 990 and 1100 (inclusive) Op. 29.01.96 Dec. date 17.05.96 - TC 9602254 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

5407.42.00 FABRIC, nylon woven, plain or ripstop, having ALL of the following: (a) composition 100% polyamide; (b) width NOT less than 154 cm; (c) weight NOT less than 41 gsm and NOT greater than 57 gsm; (d) air permeability NOT exceeding 15 ml/sq cm/s at 0.98 mbar; (e) abrasion resistance of at least 40 000 rubs at 12 kPa, Martindale abrasion method; (f) warp yarn count NOT exceeding 45 denier and AT LEAST 60 threads per cm; (g) weft yarn count NOT exceeding 45 denier and AT LEAST 40 threads per cm Op. 07.08.97 Dec. date 10.10.97 - TC 9706942 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

5509.41.00 YARN, 100% polypropylene, having ALL of the following characteristics: (a) yarn weight 59 tex; (b) yarn twists 410Z turns per metre; (c) tenacity 1800 cN; (d) 28% elongation at breaking point Op. 14.07.95 Dec. date 09.11.95 - TC 9508949 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

5509.42.00 SEWING THREAD, spun polypropylene, multiple ply, having a decitex between 200 and 290 (inclusive) per ply, 6 ply Op. 29.06.95 Dec. date 11.10.95 - TC 9508609 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

5509.61.00 YARN, boucle, 1/11 mm, 37% wool, 26% nylon, 37% acrylic Op. 01.09.95 Dec. date 04.12.95 - TC 9510263 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

5509.69.00 YARN, fancy twisted or plied, with boucle or loop effect, comprising a minimum of 60% by weight of acrylic spun yarn, remaining ply or plies of polyester and/or nylon, waxed Op. 09.08.95 Dec. date 01.12.95 - TC 9509541 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



5510.12.00 YARN, spun, viscose rayon, 2 ply, measuring NOT less than 140 decitex and NOT greater than 155 decitex Op. 15.11.04 Dec. date 01.02.05 - TC 0412268 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

5512.19.00 FABRIC, PRIMARY CARPET BACKING, 100% woven polyester, having ALL of the following: (a) weight NOT greater than 260 gsm; (b) width NOT greater than 515 cm; (c) warp and weft NOT greater than 70 ends per 10 cm Op. 30.04.03 Dec. date 21.07.03 - TC 0304935 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

5602.90 FELTS, pressed, under collar, textile backed Op. 01.07.88 Dec. date 05.12.88 - TC 8807014 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

5603.11.00 FABRIC, non-woven or not knitted, being spun bonded polyester,single, cellular,honeycomb construction,having ALL of the following:- (a) width NOT less than 440 cm with no seams or joints; (b) pleat size 10 mm or 20 mm; (c) solar heat rejection > 70%; (d) R values between 0.359 and 0.546; (e) one side coloured, other side white or off-white; (f) on a scale of 0.00 to 1.00, a shading co-efficient NOT greater than 0.34; (g) inherently resistant to bacterial growth; (h) insulating properties to control heat flow. Op. 01.07.96 Dec. date 04.07.96 - TC 9607506 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

5603.13.00 REINFORCING MATERIAL, FOOTWEAR, man-made filaments, coated with adhesive on one side and a paper backing Op. 02.09.98 Dec. date 27.11.98 - TC 9807798 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

5603.13.00 FABRIC, nonwoven, laminated, consisting of three components as follows: (a) three layer laminate with core of elastic film and facing layers of spunbond polypropylene; (b) polypropylene spunbond/meltblown/spunbond laminate; (c) extruded non cellular polypropylene microhook film Op. 18.11.98 Dec. date 29.01.99 - TC 9810190 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

5603.94 MICROWAVE ABSORBER MATERIAL, being bonded rubberised textile fabric enmeshed with coconut hair fibres and impregnated with a conductive carbon solution Op. 01.07.96 Dec. date 01.07.96 - TC 9607310 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

5607.29 ROPES, individually assembled, finished length less than 12 m, manufactured from ropes having a dia of less than 12 mm Op. 01.11.83 Dec. date 01.11.83 - TC 8340902 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

5607.50.00 CORD, PARACHUTE, nylon, 16 strand Op. 23.10.97 Dec. date 05.01.98 - TC 9610299 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



5801.35.10 FABRIC, velvet, woven on velvet looms, having All of the following: (a) a weight of 225 g/sq m or greater but NOT exceeding 295 g/sq m; (b) a backing of continuous filament viscose rayon with a viscose rayon pile; (c) a coating of heat sensitive adhesive Op. 04.02.93 Dec. date 17.05.93 - TC 9308191 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

5806.32.00 RIBBONS, polyamide, incorporating a metallised yarn, having ALL of the following characteristics: (a) three yarn colours; (b) tartan pattern; (c) width NOT less than 23 mm and NOT greater than 51 mm; (d) NOT printed Op. 23.10.97 Dec. date 06.01.98 - TC 9610417 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

5903.20.10 TAPE, MARKING, with heat activated adhesive Op. 08.01.98 Dec. date 03.04.98 - TC 9800217 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

5903.20.90 FABRIC, plain weave, having ALL of the following: (a) Backing: cotton, a weight of 80 g/sq m or greater but NOT exceeding 370 g/sq m; (b) Top Layer: pigmented polyurethane, with not less than 50 g/sq m dry process with embossed decorative pattern, able to be thermo-bonded at temperatures over 140 degrees C; (c) a width not exceeding 140 cm Op. 23.10.97 Dec. date 06.01.98 - TC 9610426 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

5903.90.90 FABRIC, FUSIBLE INTERLINING, of man-made fibre, weft inserted or warp knitted construction with dot type or powder point form of coating of polyamide copolymer resins with a bond strength of 5 newtons per 5 cm of fabric Op. 30.07.97 Dec. date 08.12.97 - TC 9706692 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

5903.90.90 FABRIC, FILM MAGAZINE LIGHT LOCK, having ALL of the following: (a) ground warp: 40 filament, 120 denier, 2.1 turns per inch (25.4 mm), viscose rayon yarn, with number of ends per inch (25.4 mm) in the range 180 to 190; (b) filling: made of same yarn as in (a) above, with number of picks per inch (25.4 mm) in the range 94 to 104; (c) pile warp: 52 filament, 100 denier nylon yarn, with number of ends per inch (25.4 mm) in the range 87 to 98; (d) heat activated adhesive backing; (e) widths in range 6 mm to 12 mm; (f) black colour only Op. 24.09.97 Dec. date 12.12.97 - TC 9708478 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

5907.00 FABRIC, WOVEN COTTON, flock coated on one side and on the reverse side to a thickness of 0.2 mm with a heat activated adhesive reactivable at temperatures of LESS than 60 degrees C Op. 07.03.90 Dec. date 11.04.91 - TC 9003017 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



5911.10.00 FABRIC, woven cotton/polyester blend coated with black butadiene/ polysulphide blend rubber, thickness NOT less than 0.39 mm but NOT exceeding 0.47 mm, uncured, formulated for conversion into convoluted diaphragms for domestic gas meters Op. 25.06.93 Dec. date 01.10.93 - TC 9304678 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

5911.90.90 FABRIC COVERS, DAMPNER ROLLER, woven, water absorbing, having a maximum diameter NOT exceeding 300 mm, in lengths NOT less than 20 m and NOT exceeding 30 m Op. 02.06.98 Dec. date 11.09.98 - TC 9804737 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

6001.91.00 FABRIC COVERS, DAMPNER ROLLER, tubular knitted, water absorbing, having a maximum diameter NOT exceeding 300 mm, in lengths NOT less than 20 m and NOT exceeding 30 m Op. 02.06.98 Dec. date 14.08.98 - TC 9804768 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

6001.99.00 FABRIC COVERS, DAMPNER ROLLER, tubular knitted, water absorbing, having a maximum diameter NOT exceeding 300 mm, in lengths NOT less than 20 m and NOT exceeding 30 m Op. 02.06.98 Dec. date 14.08.98 - TC 9804735 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

6004.10.00 FABRIC, PATTERNED LACE, cotton or man made fibre other than polyester, having ALL of the following characteristics: (a) produced on a multibar pattern Raschel machine; (b) 36 gauge or finer; (c) NOT less than 5% elastomeric yarn; (d) width exceeding 30 cm Op. 01.01.02 Dec. date 09.01.02 - TC 0108340 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

6005.31.00 NETTING, WARP KNIT RASCHEL, having ALL of the following: (a) made from polyethylene strip of a width NOT less than 0.5 mm and NOT greater than 1.5 mm; (b) mesh size greater than 400 sq mm; (c) weight of netting NOT greater than 12 g per square metre Op. 18.02.03 Dec. date 02.05.03 - TC 0301552 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

6005.31.00 NETTING, KNOTLESS, of polyamide multifilament yarn, 210 denier, ply rating NOT greater than 400 ply Op. 19.07.04 Dec. date 11.10.04 - TC 0407343 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

6006.32.00 FABRIC, NON-TEXTURED POLYESTER, knitted and dyed, flame retardant to DIN Standard 4102 B1, in widths NOT less than 195 cm and NOT greater than 300 cm Op. 29.08.03 Dec. date 07.11.03 - TC 0310741 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

6302.93.00 CLOTHS, SKIN EXFOLIATION, open knitted nylon fabric, double layer, weight NOT less than 130 gsm and NOT exceeding 150 gsm Op. 19.07.99 Dec. date 01.10.99 - TC 9905373 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



6305.32.00 CONTAINERS, FLEXIBLE INTERMEDIATE BULK, compliant with AS 3668 1989 AND/OR United Nations Dangerous Goods Standard (packaging group II and III), comprising ALL of the following: (a) single point lift with a double sewn protective sleeve; (b) container body U.V. treated circular woven polypropylene; (c) open top; (d) container having star sewn closed bottom OR flat square sewn closed bottom; (e) liners, LDPE bottleneck suspended OR pillow type; (f) safe working load NOT less than 500 kg and NOT greater than 2 000 kg Op. 05.02.04 Dec. date 27.05.04 - TC 0401447 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

6305.32.00 CONTAINERS, FLEXIBLE INTERMEDIATE BULK, compliant with Australian Standard 3668-1989, and the Australian Code for the Transport Of Dangerous Goods by Road and Rail, having ALL of the following: (a) width greater than 1 metre; (b) U.V. treated, flat woven polypropylene body, top fitted filling spout and closed bottom, all assembled using polypropylene sewing threads; (c) safe working load NOT less than 1 100 kg Op. 31.05.04 Dec. date 13.08.04 - TC 0405193 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

6307.90 CHUTES, escape, tubular, having an inner layer of kevlar and a protective elastic fabric layer, with or without a third layer of fibreglass fabric for heat insulation Op. 06.06.85 Dec. date 29.11.85 - TC 8532349 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

6307.90.10 MAGNETIC PRODUCTS, incorporating magnets, NOT having a composition of long pile fabric, being EITHER of the following; (a) neck and head wrap; (b) wrist supports Op. 08.11.00 Dec. date 15.02.01 - TC 0009292 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

6307.90.99 INSERTS, LID, PADDED EFFECT, JEWELLERY PRESENTATION BOX, comprising woven satin fabric cut roughly to shape and glued on the reverse or the face of the four inward folding sides of the insert to a paperboard reinforcement which has been cut to shape and size and creased to permit insertion Op. 23.10.97 Dec. date 09.01.98 - TC 9610642 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

6307.90.99 MATTING, woven polyester monofilament, with OR without the following: (a) fibreglass or carbon composite re-inforcing rods; (b) selvage or other edge finishing; (c) stainless steel eyelets Op. 11.02.02 Dec. date 26.04.02 - TC 0201276 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

6402.19.00 BASEBALL SHOES, without heel, having moulded rubber cleats and moulded rubber conical stops Op. 15.08.96 Dec. date 01.11.96 - TC 9609805 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

6403.19.00 SOCCER BOOTS, having BOTH of the following: (a) moulded cleats OR studs on the sole; (b) sole insert Op. 09.01.01 Dec. date 23.04.01 - TC 0100213 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



6902.90.00 REFRACTORY BRICKS, having ALL of the following: (a) magnesium oxide (MgO) NOT less than 84%; (b) aluminium oxide (Al203) NOT less than 15%; (c) silicon dioxide (SiO2) NOT less than 0.3%; (d) bulk density NOT less than 2 970 kg/sq m Op. 22.04.04 Dec. date 09.07.04 - TC 0404037 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

6902.90.00 REFRACTORY BRICKS, having ALL of the following: (a) magnesium oxide (MgO) NOT less than 82%; (b) aluminium oxide (Al203) NOT less than 16%; (c) bulk density NOT less than 2 940 kg/sq cm Op. 22.04.04 Dec. date 09.07.04 - TC 0404038 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

6903.20 NOZZLES, welding gun Op. 01.11.83 Dec. date 01.11.83 - TC 8341157 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7019.12 ROVINGS OR YARNS, glass fibre, air textured, 68 tex OR greater Op. 01.07.96 Dec. date 01.07.96 - TC 9606686 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7019.19 YARNS, being EITHER of the following: (a) glass fibre, made up from individual yarns of 22 tex or less, with a total combination of 22 tex or less; (b) glass fibre and thermoplastic fibre combination, made up from individual strands or yarns of 11 tex or less, with a total combination less than 33 tex Op. 01.07.96 Dec. date 06.06.96 - TC 9605790 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7019.19 YARNS, glass fibre, coated with polytetrafluoroethylene Op. 01.07.96 Dec. date 06.06.96 - TC 9606563 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7019.90 WICKS, glass fibre, kerosene heater Op. 15.11.83 Dec. date 15.11.83 - TC 8341081 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7211.14.00 STEEL, 100 mm x 100 mm square, complying with SAE 4140 OR SAE K1045 Op. 15.07.02 Dec. date 04.10.02 - TC 0206220 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



7211.29 STRIP, steel annealed, cold rolled, in coil form having ALL of the following: (a) chemical composition by weight of ALL of the following: (i) carbon - 0.45% to 0.50% (both inclusive); (ii) manganese - 0.65% to 0.90% (both inclusive); (b) DIN standards 17 200 and 1 544; (c) in ANY of the following sizes: WIDTH THICKNESS 65 mm x 1.3 mm; 47.6 mm x 2.0 mm; 73.0 mm x 2.0 mm; 75.0 mm x 2.5 mm; 90.0 mm x 2.5 mm; 97.0 mm x 2.5 mm; 42.0 mm x 3.0 mm; 78.0 mm x 3.0 mm; 89.0 mm x 3.0 mm; 97.0 mm x 3.0 mm; 30.1 mm x 3.2 mm; 42.0 mm x 3.2 mm; 59.0 mm x 3.2 mm; 76.2 mm x 3.2 mm; 92.0 mm x 3.2 mm; 236.0 mm x 3.2 mm; (d) width tolerance + or - 1.00 mm; (e) thickness tolerance + or - 0.09 mm Op. 01.07.96 Dec. date 12.06.96 - TC 9606949 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7212.40 STRIP, steel, in coil form, cold rolled, high tensile, width 38.1 mm x thickness 0.79 mm, minimum tensile strength 950 MPa, minimum elongation 7%, hardness RC 29-30 Op. 16.10.84 Dec. date 16.10.84 - TC 8434681 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7219.21.00 FLAT ROLLED PRODUCTS, STAINLESS STEEL, grade Werkstoff No 1 4003 Op. 19.06.95 Dec. date 15.09.95 - TC 9508311 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7219.31 FLAT ROLLED PRODUCTS, having a nickel content exceeding 22.5% by weight Op. 01.01.88 Dec. date 01.01.88 - TC 8800532 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7219.33 FLAT ROLLED PRODUCTS, having a nickel content exceeding 22.5% by weight Op. 01.01.88 Dec. date 01.01.88 - TC 8800546 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7219.33.00 FLAT ROLLED PRODUCTS, stainless steel, Grade UNS 31803, having a chemical composition, by weight, of ALL the following: (a) carbon 0.03% maximum; (b) chromium 21.0-23.0% inclusive; (c) nickel 4.5-6.5% inclusive; (d) molybdenum 2.5-3.5% inclusive; (e) nitrogen 0.08-0.20% inclusive; (f) silicon 1.0% maximum; (g) manganese 2.0% maximum; (h) phosphorus 0.03% maximum; (i) sulphur 0.02% maximum Op. 10.12.92 Dec. date 12.03.93 - TC 9300333 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



7219.33.00 FLAT ROLLED PRODUCTS, stainless steel, Grade UNS S30815, having a chemical composition by weight of ALL of the following: (a) carbon 0.1% maximum; (b) silicon 1.40% to 2.00% (both inclusive); (c) manganese 0.8% maximum; (d) phosphorous 0.040% maximum; (e) sulphur 0.030% maximum; (f) chromium 20% to 22% (both inclusive); (g) nickel 10% to 12% (both inclusive); (h) cerium 0.03% to 0.08% (both inclusive); (i) nitrogen 0.14% to 0.20% (both inclusive) Op. 21.01.94 Dec. date 29.04.94 - TC 9401448 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7220.90.00 HOSE CLAMP COMPONENTS, WORM DRIVE, being pressed stainless steel hose clamp bands in continuous and/or cut and curled form, meeting ALL of the specifications in EITHER "TABLE A" or "TABLE B" as follows: TABLE A (a) width within the range of 12.57 mm to 12.83 mm inclusive; (b) material thickness within the range of 0.60 mm to 0.67 mm inclusive; (c) multiple screw slots at an angle of 6 degrees to the band width, being within the range of 3.09 mm to 3.31 mm inclusive of one side of the band, having ALL of the following: (i) a slot width within the range of 1.06 mm to 1.10 mm inclusive; (ii) a slot length within the range of 6.49 mm to 6.69 mm inclusive; (iii) a slot pitch within the range of 2.53 mm to 2.55 mm inclusive; (d) having a hose clamp housing attachment slot within the band’s longitudinal length; TABLE B (a) width within the range of 7.80 mm to 10.42 mm inclusive; (b) material thickness within the range of 0.55 mm to 0.61 mm inclusive; (c) multiple screw slots at an angle of 7 degrees to the band width, being within the range of 1.52 mm to 1.78 mm of one side of the band, having ALL of the following: (i) a slot width within the range of 0.88 mm to 0.92 mm inclusive; (ii) a slot length within the range of 4.89 mm to 4.99 mm inclusive; (iii) a slot pitch within the range of 2.02 mm to 2.04 mm inclusive; (d) having a hose clamp housing attachment notch, on either side of the band within the band’s longitudinal length, with the following dimensions: (i) length within the range of 5.33 mm to 5.57 mm inclusive; (ii) width within the range of 0.88 mm to 1.15 mm inclusive; (e) having a screw recess within the band’s longitudinal length Op. 22.12.95 Dec. date 03.05.96 - TC 9600750 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7223.00 WIRE to AISI Specifications 302 or 304, resin or nickel coated, dia 0.46 mm or greater but NOT exceeding 1.04 mm Op. 21.02.84 Dec. date 21.02.84 - TC 8341713 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



7223.00 WIRE, stainless steel, to Specification AISI 302/304, having ALL of the following: (a) dia 1.4 mm or greater but NOT exceeding 2.5 mm; (b) surface finish within 0.25 microns; (c) tensile strength NOT less than 1 550 MPa Op. 08.07.85 Dec. date 08.07.85 - TC 8532943 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7223.00.00 WIRE, stainless steel, cold rolled and annealed with round edges, to specification A1S1201, in ANY of the following sizes: width (+ or - 0.064mm) thickness (+ or – 0.019mm) (a) 2.540 mm (0.100") x .381 mm (0.015") (b) 3.048 mm (0.120") x .381 mm (0.015") (c) 2.540 mm (0.100") x .406 mm (0.016") (d) 3.048 mm (0.120") x .406 mm (0.016") (e) 2.540 mm (0.100") x .457 mm (0.018") (f) 3.048 mm (0.120") x .457 mm (0.018") (g) 3.048 mm (0.120") x .508 mm (0.020") (h) 3.302 mm (0.130") x .508 mm (0.020") (i) 3.302 mm (0.130") x .558 mm (0.022") (j) 2.540 mm (0.100") x .508 mm (0.020") Op. 01.09.94 Dec. date 13.12.94 - TC 9407311 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7225.19.00 SHEET OR STRIP, electrical steel, cold rolled, non-oriented as defined in IEC 404-8 Section 4, having a core loss of less than 2.3 W/kg at a flux density of 1.0 tesla and frequency of 50 Hz as determined by test methods to IEC 404-2 Op. 01.07.96 Dec. date 12.06.96 - TC 9607091 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7225.40.00 PLATE OR SHEET, STEEL, 9% nickel alloy, complying with ASTM A353 and ASTM A553 type 1 Op. 16.06.04 Dec. date 27.08.04 - TC 0405889 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7226.91.00 BARS, flat, to specification AISI-01, having a thickness NOT exceeding 100 mm or a width NOT exceeding 300 mm Op. 11.03.93 Dec. date 18.06.93 - TC 9308738 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7226.91.00 PLATES, SHEETS AND FLATS, low alloy, to specification DIN 62SiMnCr4 Op. 14.02.95 Dec. date 31.05.95 - TC 9504062 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7226.91.00 PLATES, SHEETS OR FLATS, high alloy steel, having a chemical composition by weight of ALL of the following: (a) carbon - 1.10%; (b) silicon - 0.90%; (c) manganese - 0.40%; (d) chromium - 8.30%; (e) molybdenum - 2.10%; (f) vanadium - 0.50%; (g) + aluminium; (h) + niobium Op. 04.04.96 Dec. date 05.07.96 - TC 9605299 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



7228.10.00 BARS, high speed steel, manufactured by the powder metallurgy process, containing NOT less than 6% vanadium by weight Op. 12.08.94 Dec. date 11.11.94 - TC 9406815 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7228.10.00 MACHINE KNIFE BLANKS, high speed steel, hardened and tempered to specification A1S1-M2 and A1S1-T1, having ALL of the following: (a) ground square or bevelled edge; (b) minimum length 600 mm; (c) minimum width 12.5 mm; (d) minimum thickness 3 mm Op. 16.11.95 Dec. date 01.03.96 - TC 9512632 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7228.30.10 BARS AND RODS, high alloy steel, to specification DIN X40CrMoV51, BS BH13 or AISI H13, in either of the following sizes: (a) Less than 200 mm diameter; (b) Greater than 710 mm diameter Op. 14.02.95 Dec. date 05.06.95 - TC 9504071 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7228.30.10 BARS AND RODS, high alloy, to specification DIN 60WCrV7 Op. 14.02.95 Dec. date 31.05.95 - TC 9504082 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7228.30.10 BARS AND RODS, high alloy steel, to specification DIN 40CrMnMoS8 6, hardened and tempered within the range of 950-1100 N per square millimetre (both inclusive) Op. 14.02.95 Dec. date 31.07.95 - TC 9508564 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7228.40 BARS, flat, alloy steel, having ALL of the following: (a) width less than 150.0 mm; (b) thickness exceeding 3.25 mm but less than 50.00 mm; (c) length NOT exceeding 10.0 m Op. 13.07.94 Dec. date 13.07.94 - TC 8736256 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7228.40 BARS, flat, to Specification AISI-D2, having a width NOT exceeding 200.0 mm and a thickness NOT exceeding 60.0 mm Op. 14.04.88 Dec. date 30.06.88 - TC 8804309 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7228.50.00 BARS, flat, having a thickness NOT exceeding 200 mm and a width NOT exceeding 520 mm, to ANY of the following specifications: (a) AISI-01; (b) BS 4659: 1989, in ANY of the following grades: (i) BA 6; (ii) BD 2; (iii) BD 2A; (iv) BD 6; (v) BO 1; (c) DIN 1.2101 Op. 01.07.95 Dec. date 03.07.95 - TC 9505815 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



7228.60.10 BARS AND RODS, high alloy steel, having a chemical composition by weight of ALL of the following: (a) carbon 2.30% (b) silicon 0.40% (c) manganese 0.40% (d) chromium 12.50% (e) molybdenum 1.10% (f) vanadium 4.00% annealed to maximum 280HB Op. 14.02.95 Dec. date 31.05.95 - TC 9504079 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7228.70.00 DISCS, forged P20 steel, having BOTH of the following: (a) outside diameter NOT less than 245.0 cm and NOT greater than 248.0 cm; (b) Brinell Surface Hardness: 285/285/285 HBW Op. 22.12.04 Dec. date 18.03.05 - TC 0413763 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7229.90 WIRE, steel, aluminised Op. 28.02.84 Dec. date 28.02.84 - TC 8341678 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7229.90 WELDING WIRE, metal inert gas, dia 1.2 mm (+ or - 0.02 mm) or 1.6 mm (+ or - 0.05 mm), having a chemical composition by weight of ALL of the following: (a) carbon - 0.10% maximum; (b) manganese - 1.5% to 1.7% (both inclusive); (c) silicon - 0.4% to 0.6% (both inclusive); (d) sulphur - 0.015% maximum; (e) phosphorus - 0.015% maximum; (f) chromium - 0.2% to 0.4% (both inclusive); (g) molybdenum - 0.2% to 0.3% (both inclusive); (h) vanadium - 0.05% to 0.10% (both inclusive); (i) nickel - 1.2% to 1.6% (both inclusive) Op. 21.02.84 Dec. date 05.08.86 - TC 8633469 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7304.31 TUBES OR HOLLOW BARS (NOT being honed tubes), in straight lengths, ends plain, bevelled or threaded in accordance with ANY of the following tube, hollow bar or Pipe Material Specification options: (a) AS; (b) ASME; (c) ASTM; (d) BS; (e) DIN, but without further rework, having a length NOT less than four times the OD, as listed in THE TABLE: THE TABLE Outside Dia Wall Thickness (a) NOT exceeding 219.08 mm 13.00 mm or greater but NOT exceeding 25.00 mm; (b) 219.08 mm or greater but 12.70 mm or greater but NOT exceeding 254.00 mm NOT exceeding 50.80 mm; (c) 254.00 mm or greater but 19.05 mm or greater but NOT exceeding 323.85 mm NOT exceeding 41.00 mm; (d) 323.85 mm or greater but 25.40 mm or greater but NOT exceeding 720.73 mm NOT exceeding 75.00 mm Op. 01.01.88 Dec. date 01.01.88 - TC 8735570 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



7304.31.00 TUBES, seamless, carbon steel, cold drawn, stress relieved to specification SAE 1541, having ALL the following: (a) having a length of 3 m to 6 m inclusive; (b) O.D. 40 mm or greater but NOT exceeding 127 mm; (c) having a tolerance in straightness of 1 mm in 6 000 mm Op. 30.12.96 Dec. date 25.03.97 - TC 9613284 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7304.39 TUBES, seamless, carbon steel, hot finished, in straight lengths, ends plain, bevelled or threaded, but without further rework, to specification BS6258, grade 600 Op. 20.08.92 Dec. date 17.12.92 - TC 9207673 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7304.59 TUBES (OTHER THAN honed tubes), alloy steel, in straight lengths, ends plain, bevelled or threaded in accordance with ANY of the following Pipe Material Specification options: (a) AS; (b) ASME; (c) ASTM; (d) BS; (e) DIN, but without further rework, being EITHER of the following: (a) containing chromium but containing less than 10% chromium, having EITHER of the following: (i) OD NOT exceeding 203 mm and a WT 13 mm or greater but NOT exceeding 25 mm; (ii) OD 203 mm or greater but NOT exceeding 406 mm and a WT NOT exceeding 25 mm; (b) containing NOT less than 12% of chromium, annealed, having a length NOT less than four times the OD and having ANY of the following: (i) OD NOT less than 406 mm and a WT NOT exceeding 40 mm; (ii) OD NOT less than 610 mm and a WT NOT exceeding 75 mm; (iii) OD NOT less than 1 250 mm Op. 03.07.87 Dec. date 04.09.87 - TC 8734522 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7304.59 TUBES OR HOLLOW BARS (NOT being honed tubes), in straight lengths, ends plain, bevelled or threaded in accordance with ANY of the following tube, hollow bar or Pipe Material Specification options: (a) AS; (b) ASME; (c) ASTM; (d) BS; (e) DIN, but without further rework, having a length NOT less than four times the OD, as listed in THE TABLE: THE TABLE Outside Dia Wall Thickness (a) NOT exceeding 219.08 mm 13.00 mm or greater but NOT exceeding 25.00 mm; (b) 219.08 mm or greater but 12.70 mm or greater but NOT exceeding 254.00 mm NOT exceeding 50.80 mm; (c) 254.00 mm or greater but 19.05 mm or greater but NOT exceeding 323.85 mm NOT exceeding 41.00 mm; (d) 323.85 mm or greater but 25.40 mm or greater but NOT exceeding 720.73 mm NOT exceeding 75.00 mm Op. 01.01.88 Dec. date 01.01.88 - TC 8735575 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



7305.11.00 LINE PIPE, submerged arc welded, to API 5L grade X65, having BOTH of the following: (a) diameter NOT less than 1 000 mm; (b) wall thickness NOT less than 20 mm Op. 06.12.02 Dec. date 07.03.03 - TC 0211589 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7305.11.00 LINE PIPE, submerged arc welded, API 5L grade X65, having BOTH of the following: (a) outside diameter NOT less than 660 mm and NOT greater than 675 mm; (b) wall thickness NOT less than 20 mm and NOT greater than 27 mm Op. 01.12.03 Dec. date 08.03.04 - TC 0315202 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7305.11.00 LINE PIPE, submerged arc welded, to API 5L grade X65, having BOTH of the following: (a) outside diameter greater than 720 mm and NOT greater than 760 mm; (b) wall thickness greater than 20 mm and NOT greater than 30 mm Op. 23.09.04 Dec. date 10.12.04 - TC 0409751 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7305.39.00 CHUTE PIPES, LOADING AND UNLOADING, BARLEY GERMINATOR, stainless steel, welded, circular cross section diameter NOT less than 600 mm Op. 06.04.05 Dec. date 10.06.05 - TC 0503785 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7306.30 TUBES, ERW steel, aluminium killed, having BOTH of the following: (a) OD greater than 103 mm; (b) WT 2 mm or less Op. 01.01.88 Dec. date 01.01.88 - TC 8802581 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7308.90.00 ANCHOR FRAMES, BOILER, structural steel Op. 07.01.05 Dec. date 18.03.05 - TC 0500220 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7311.00.00 CYLINDERS, GAS, CARBON DIOXIDE FIREFIGHTING, high pressure, seamless, having ALL of the following: (a) gas capacity 45 kg; (b) water capacity 67.5 kg; (c) test pressure of NOT less than 7 MPa Op. 25.02.97 Dec. date 23.04.97 - TC 9701651 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7312.10.00 STEEL STRAND, 7 wire, 18.5 mm OR greater compacted strand, to BS 5896/3, breaking load 445 kN or greater, unoiled Op. 08.05.01 Dec. date 03.08.01 - TC 0103883 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7315.11 CHAIN, transmission, precision roller, single strand, conforming to Australian Standard AS 1532-1974 incorporating BS 228 and B 29.1 having a pitch of 76.2 mm, without attachments Op. 01.12.87 Dec. date 14.02.91 - TC 9009093 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



7315.11.00 CHAIN, GILLING MACHINE, having ALL of the following: (a) 9.525 mm pitch; (b) interconnected carriers; (c) transportation of fallers by an extension of the fallers into the chain; (d) overall width of 28 mm between outer plates Op. 28.06.93 Dec. date 01.10.93 - TC 9304707 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7315.82.00 CHAINS, alloy steel, round link, having ALL of the following: (a) compliance with ANY of the following standards: (i) DIN6523; (ii) DIN5310; (iii) DIN4878; (iv) DIN4713; (v) DIN4724; (vi) DIN4742; (vii) DIN4301; (viii) DIN4828; (ix) DIN4821; (x) DIN4762; (xi) DIN4841; (xii) AISI321 (b) nominal chemical analysis complying with ANY single line of the following table: TABLE Cr% Ni% Ti% Al% (i) 0.4-0.6 0.4-0.7 (ii) less than or equal to 0.5 (iii) 17.0-19.0 9.0-12.0 less than or equal to 0.8 (iv) 6.0-8.0 0.5-1.0 (v) 12.0-14.0 0.7-1.2 (vi) 17.0-19.0 0.7-1.2 (vii) 17.0-20.0 8.0-10.0 (viii) 19.0-21.0 11.0-13.0 (ix) 24.0-27.0 3.5-5.5 (x) 23.0-26.0 1.2-1.7 (xi) 24.0-26.0 19.0-22.0 (xii) 19.0 12.0 0.4 (c) material diameter of 21 mm or greater; (d) internal link diameter (pitch) of 76 mm or greater; But NOT including steel chain complying with EITHER DIN 17100 OR DIN 17115 Op. 21.08.95 Dec. date 04.09.95 - TC 9509458 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7318.15.00 FRAME FIXERS, preassembled, non expanded, capable of being hammered like a nail without predrilling into G2 and G4 AAC concrete, having ALL of the following: (a) helicoidal interlocking segments; (b) a ribbed sleeve mounted onto a plug unable to rotate relative to each other; (c) through fixing for flush mounted items; (d) removable and adjustable neck so that the object being fixed can be removed or adjusted by a maximum of 10 mm while the plug remains in position Op. 10.01.95 Dec. date 20.04.95 - TC 9500755 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



7318.15.00 SCREWS, COMPUTER, ARMATURE STOP, having ALL of the following: (a) zinc coated steel composition; (b) hexagonal head width 6.35 mm with linear tolerance of 0.15 mm; (c) maximum shaft length 4.83 mm with 1.3 mm unthreaded; (d) minimum failure torque of 149.14 Newtons per centimetre Op. 16.12.97 Dec. date 27.02.98 - TC 9711088 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7318.22 WASHERS, thrust (races), having a minimum hardness of 655 Victor Paterson Nickels Test or 58 Hardness Rockwell Count and a surface finish radius of 0.5 microns across or 20 micro in. sectionalised Op. 21.03.85 Dec. date 21.03.85 - TC 8531112 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7326.20 CLIPS, calyx, carnation Op. 04.11.85 Dec. date 27.02.86 - TC 8534893 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7326.90.90 LINKS, METALLIC CARTRIDGE BELT Op. 18.02.99 Dec. date 30.04.99 - TC 9901208 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7409.21 BRASS COIL, any width exceeding 100 mm, with a thickness greater than 2.2 mm Op. 03.05.91 Dec. date 24.07.91 - TC 9104330 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7409.21.00 BRASS COIL, thickness exceeding 1.5 mm, width exceeding 599 mm Op. 11.11.93 Dec. date 04.03.94 - TC 9313156 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7419.99.00 CLAMP HOLDER, being a clamp dispenser head (platform), drop forged bronze Op. 06.04.93 Dec. date 12.07.93 - TC 9309108 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7605.29 WIRE, aluminium alloy, conforming to the following specifications sizes: (a) Flat profile (i) 3.00 mm + or - 0.020 mm x 0.77 mm + or - 0.020 mm (ii) 4.20 mm + or - 0.020 mm x 0.90 mm + or - 0.020 mm (b) "Y" profile (i) 3.567 mm + 0.100 mm or - 0.050 mm x 2.608 mm + 0.020 mm or - 0.040 mm x 1.210 mm + 0.010 mm or - 0.030 mm Op. 31.10.90 Dec. date 11.07.91 - TC 9009371 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



7607.20.00 FOIL, aluminium, laminated by wax to paper, lacquered, having ALL of the following: (a) foil layer NOT exceeding 24 gsm; (b) laminating wax layer NOT exceeding 9 gsm; (c) paper layer NOT exceeding 34 gsm; (d) paraffin wax layer NOT exceeding 7 gsm; (e) microperforations having a diameter of 0.2 mm (+ OR - 0.1 mm) no more than 7 mm apart Op. 08.09.97 Dec. date 14.11.97 - TC 9707916 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7612.90.00 CONTAINERS, CYLINDRICAL, STORAGE AND TRANSPORT, 127 MM (5") 54 CALIBRE PROPELLING CHARGE Op. 11.08.98 Dec. date 30.10.98 - TC 9807094 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7612.90.00 CONTAINERS, ALUMINIUM, FOOD, having ALL of the following: (a) polypropylene lining; (b) aluminium lids; (c) depth NOT less than 28.30 mm but NOT exceeding 39.20 mm; (d) volume NOT less than 248.40 ml but NOT exceeding 338.70 ml Op. 03.07.03 Dec. date 26.09.03 - TC 0308129 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7615.19 STOVE SETS, portable, being all weather outdoor spirit burner types, comprising ALL of the following: (a) frying pan; (b) saucepans; (c) wind shield upper; (d) wind shield lower; (e) spirit burner with screw cap; (f) handle Op. 01.07.96 Dec. date 14.03.96 - TC 9602736 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7616.99 ROLLER FRAMES, adjustable, fabric tensioning, screen-printing Op. 01.07.96 Dec. date 25.03.96 - TC 9602829 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

7616.99.00 WINGBANDS, CHICKEN, aluminium, bearing an identifying serial number and bar code imprint Op. 03.05.99 Dec. date 16.07.99 - TC 9903003 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8204.20.00 WRENCH SETS, insulated, complying with IEC 900 standard, tested to 10 000 V Op. 25.01.94 Dec. date 06.05.94 - TC 9402006 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8205.70 CRAMP, flooring, for attachment to joists for closing floorboards before nailing Op. 27.06.91 Dec. date 20.12.91 - TC 9106182 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8207.50 DRILL HEADS, metal working, disposable type, being components of a twin tube drilling system capable of drilling holes over 18 mm in dia and to a hole depth of 3 500 mm, in blank form where the tungsten carbide tips and wear pads on the drill head have not been ground to their final size Op. 05.12.86 Dec. date 23.06.89 - TC 8636123 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



8207.70.00 CUTTER, METAL MILLING, diameter 210 mm Op. 14.05.96 Dec. date 16.08.96 - TC 9607144 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8207.90 MORTISE CUTTING CHAINS, LINKS OR PINS, having ANY of the following nominal pitches: (a) 22.6 mm; (b) 15.7 mm; (c) 13.7 mm Op. 13.04.88 Dec. date 07.07.89 - TC 8803699 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8207.90 CUTTER, multifunction round hole, with adjustable radius blade arm, single point cutting blad and depth control, with self contained dust collection hood, having a cutting dia of between 40 mm to 163 mm (both inclusive) Op. 29.08.90 Dec. date 25.01.91 - TC 9007536 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8208.20 FLAKER KNIVES, having a discontinuous cutting edge on the major face and having a stepped surface, with overall dimensions as follows: (a) length 569.3 mm; (b) width 57 mm; (c) thickness 5 mm Op. 17.04.92 Dec. date 21.08.92 - TC 9204168 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8208.90 KNIVES, toothed carpet tufting machine Op. 07.02.84 Dec. date 07.02.84 - TC 8341972 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8208.90 BLADES, cutting, being replaceable tools for printed circuit board component inserting machines Op. 21.06.85 Dec. date 14.10.85 - TC 8532579 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8208.90 BLADES, electric poultry debeaker Op. 25.07.86 Dec. date 28.10.86 - TC 8634351 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



8209.00.00 CONVERSION AND MODIFICATION EQUIPMENT, AUTOMOTIVE ENGINE COMPONENT MANUFACTURING AND/OR ASSEMBLY MACHINES, being double over-head cam engine head machining centre interchangeable tool tips, bites OR inserts Op. 25.09.95 Dec. date 07.01.96 - TC 9510833 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8302.10.00 HINGES, c-clip spring, metal cased jewellery presentation box Op. 28.01.93 Dec. date 10.05.93 - TC 9308109 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8302.49.00 FASTENER AND CATCHPLATE, stainless steel, having a length between 50mm and 90mm (inclusive) and a width between 10mm and 30mm (inclusive) Op. 20.01.95 Dec. date 09.05.95 - TC 9501021 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8308.10.00 LACE HOOKS, footwear Op. 01.12.94 Dec. date 24.03.95 - TC 9409447 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8402.19.00 POWER AND STEAM GENERATORS, comprising ALL of the following: (a) gas turbine generator; (b) switch gear; (c) transformers; (d) standby diesel generator; (e) boilers; (f) heat exchanger; (g) water purifier; (h) distributor; (i) controllers Op. 25.10.04 Dec. date 03.03.05 - TC 0411084 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8412.21.00 ACTUATORS, MIXED GAS SHUT-OFF VALVE Op. 07.02.05 Dec. date 22.04.05 - TC 0501479 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8412.29 ACTUATORS, log and pulp loading crane grapple Op. 10.01.86 Dec. date 29.04.86 - TC 8632070 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8413.50.10 PUMPS, positive displacement, hydraulic, reciprocating horizontal quintuplex plunger Op. 06.10.04 Dec. date 10.12.04 - TC 0410544 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8413.50.90 PUMPS, DOUBLE ACTING PISTON, complete with all internal air valving, incorporating an air motor having a diameter of 107.95 mm OR greater Op. 31.05.95 Dec. date 22.09.95 - TC 9505861 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



8413.50.90 PUMPS, positive displacement, valveless, modular, single OR multi-head, having ALL of the following: (a) capacity to pump both liquids and gases; (b) flow rate of 0.3 ml/min OR greater, but NOT exceeding 1.5 l/ min; (c) operating pressure up to 700 kPa; (d) flow rate accuracy of + or - 1% of rated flow Op. 10.12.97 Dec. date 27.02.98 - TC 9710912 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8413.70.90 PUMPS, submersible, centrifugal, multistage, having ALL of the following features: (a) petrol cooled thermal protected electric motor NOT exceeding 1.12 kW; (b) head exceeding 30 m when measured at 0 L/min and nominal 2 800 r/min; (c) pump and motor outside diameter NOT exceeding 103 mm; (d) integral thermal relief and check valve; (e) complying with SAA Approval No. AUS Ex3028X for Zone 1Exs11AT4 hazardous area Op. 27.04.94 Dec. date 31.08.94 - TC 9404371 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8413.70.90 PUMPS, CENTRIFUGAL, multi speed operation, having ALL of the following: (a) multi stage within the range from 2 to 8 (both inclusive); (b) water temperature within the range of 80 degrees C and 220 degrees C (both inclusive); (c) pump input power within the range of 300 kW and 7 000 kW (both inclusive); (d) operating differential head 3 500 metres OR less; (e) flow capacity 350 kg/second OR less Op. 13.11.97 Dec. date 23.01.98 - TC 9710077 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8413.91.90 INLET BODIES, AUTOMOTIVE FUEL IMPELLER PUMP Op. 05.01.04 Dec. date 31.03.04 - TC 0400085 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8414.10.00 DUST CYCLONE BLOWERS, SINTER EMISSION PLANT, comprising ALL of the following: (a) cast iron three lobe rotors; (b) carbonised, quenched and ground chrome molybdenum timing gear; (c) timing splash gear lubricated with oil bath; (d) weighing NOT less than 700 kg Op. 19.08.03 Dec. date 17.11.03 - TC 0310248 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8414.80.19 COMPRESSORS, AIR BRAKE UNIT, reciprocating piston, having a delivery NOT less than 600 litres per minute at a speed of 970 r/min and NOT greater than 980 litres per minute at a speed of 1 450 r/min Op. 30.06.03 Dec. date 26.09.03 - TC 0307823 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8414.90.90 PARTS, HOT GAS RECIRCULATOR IMPELLOR, being a backward curved vane type turbo fan and main shaft Op. 18.08.03 Dec. date 17.11.03 - TC 0310245 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



8414.90.90 IMPELLORS, HOT GAS, SINTER EMISSION PLANT, with shaft and hub Op. 10.06.04 Dec. date 27.08.04 - TC 0405757 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8414.90.90 FAN BLADES, aluminium, having a length greater than 2 metres Op. 23.09.04 Dec. date 07.12.04 - TC 0409899 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8416.20.00 BURNERS, WASTE GAS, comprising ALL of the following: (a) burner; (b) nozzles; (c) thermowell; (d) thermocouple; (e) junction box Op. 23.04.99 Dec. date 09.07.99 - TC 9902832 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8416.20.00 BURNERS, PULVERISED COAL Op. 29.10.03 Dec. date 23.01.04 - TC 0313786 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8417.90.00 TUBES AND FITTINGS, ETHYLENE STEAM CRACKING FURNACE, having BOTH of the following: (a) chromium content NOT less than 24% and NOT greater than 28%; (b) nickel content NOT less than 33% and NOT greater than 37% Op. 28.05.03 Dec. date 15.08.03 - TC 0306409 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8417.90.00 SKID BUTTONS, HOT STRIP MILL RE-HEAT FURNACE Op. 17.12.04 Dec. date 21.02.05 - TC 0413841 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8417.90.00 LONGITUDINAL OR CROSS BEAMS, TRANSFER FRAME, WALKING BEAM FURNACE Op. 07.04.05 Dec. date 17.06.05 - TC 0504198 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8418.69 FREEZERS, ice-cream or flavoured ice bars, capable of ALL the following: (a) filling moulds with liquid product; (b) inserting sticks; (c) automatic removal of the frozen product Op. 03.07.85 Dec. date 01.01.88 - TC 8532898 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8419.39.90 TUNNEL DRIERS, SANITARYWARE Op. 06.10.04 Dec. date 10.12.04 - TC 0410523 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



8419.40.00 STILLS, WATER FOR INJECTION, PLC, five effect, having ALL of the following: (a) gravitational purifier; (b) baffle free contamination chamber; (c) process validator Op. 08.09.04 Dec. date 15.11.04 - TC 0409190 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8419.50.90 HEAT EXCHANGERS, MALTING KILN, having a horizontal glass tube Op. 25.02.05 Dec. date 06.05.05 - TC 0502574 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8419.81 BAKING MACHINES, doughnut Op. 27.02.89 Dec. date 15.10.92 - TC 9207038 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8419.81.90 GRILLERS, CONVEYOR BELT, CONTINUOUS, computer controlled, comprising ALL of the following: (a) thermal oil heater; (b) platens; (c) belt height adjuster; (d) steam cleaner Op. 30.08.02 Dec. date 22.11.02 - TC 0208025 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8419.81.90 BREAD ROLL TOASTED SANDWICH MAKERS, comprising ALL of the following: (a) bread roll toaster; (b) refrigerated preparation cabinet; (c) meat steamer with stand Op. 28.07.04 Dec. date 18.10.04 - TC 0407730 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8419.89 HEATERS, plate coil, drum, internal or external type Op. 16.03.84 Dec. date 16.03.84 - TC 8437449 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8419.89 HEATERS, liquid, in line, being a pipeline insert, using steam as the heating medium Op. 19.08.85 Dec. date 06.01.86 - TC 8534290 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8419.89.90 TEMPERING FURNACES, FLOAT GLASS, computer controlled, comprising ALL of the following: (a) horizontal oscillating roller hearth; (b) electric radiation and convection heating chamber; (c) two air quenches Op. 21.08.01 Dec. date 02.11.01 - TC 0107300 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8419.89.90 OXIDISERS, REGENERATIVE, thermal, having BOTH of the following: (a) electric pre heater; (b) flow greater than 12 000 Nm3/h Op. 19.08.04 Dec. date 29.10.04 - TC 0408549 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



8419.89.90 CALCINATION PLANTS, ALUMINA HYDRATE, comprising ALL of the following: (a) pan filters; (b) calciners; (c) baghouse OR electrostatic precipitators Op. 20.08.04 Dec. date 29.10.04 - TC 0408598 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8419.89.90 DIGESTION PLANTS, BAUXITE SLURRY, comprising ALL of the following: (a) holding tanks; (b) digestor vessels; (c) flash tanks; (d) heat exchangers Op. 20.08.04 Dec. date 29.10.04 - TC 0408607 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8419.89.90 POLYCONDENSATORS, solid state, comprising all of the following: (a) crystalliser; (b) vacuum transporter; (c) preheater; (d) solid state reactor Op. 30.11.04 Dec. date 25.02.05 - TC 0412876 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8419.89.90 CURING CHAMBERS, LEAD ACID BATTERY POSITIVE AND NEGATIVE PLATES Op. 26.11.04 Dec. date 04.02.05 - TC 0412997 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8420.91.00 ROLLS, PAPER MAKING MACHINE, centre press, ceramic covered Op. 12.04.99 Dec. date 25.06.99 - TC 9902504 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8420.91.00 ROLL SHELLS, SUCTION, PAPER OR PAPERBOARD MAKING MACHINE Op. 18.10.02 Dec. date 10.01.03 - TC 0209790 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8421.21.90 FILTERS, plastic, having ALL of the following: (a) inlet/outlet NOT exceeding 3.81 cm; (b) flow rate 0.1 cu m/h - 15 cu m/h; (c) Y shaped body; (d) screen constructed of stainless steel 316 AND single plain weave woven nylon moulded into a polypropylene support cage; (e) screen retention range from 10 microns - 800 microns; (f) inline installation with male threaded connectors Op. 30.03.98 Dec. date 19.06.98 - TC 9802721 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8421.22.00 STABILISERS, BEER Op. 23.02.05 Dec. date 06.05.05 - TC 0502566 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8421.29.00 CLARIFICATION PLANTS, BAUXITE SLURRY, comprising ALL of the following: (a) mud thickeners; (b) counter current washing train; (c) scrubbers; (d) flash tanks Op. 02.09.04 Dec. date 15.11.04 - TC 0409008 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



8421.39.00 AIR STRIPPER, comprising ALL of the following: (a) feed tank; (b) feed tank jet mix nozzle; (c) feed tank vent absorber; (d) air stripper; (e) pumps; (f) air stripper blower; (g) auxilliary air filter; (h) blower acoustic enclosure Op. 24.01.05 Dec. date 08.04.05 - TC 0501204 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8421.39.00 PLANT, OXIDISATION, GAS, comprising ALL of the following: (a) off gas oxidiser; (b) flash drum; (c) waste heat boiler; (d) offgas preheater; (e) quencher; (f) scrubber; (g) absorber; (h) offgas steam heater; (i) pumps; (j) blowers; (k) heat exchangers; (l) tanks; (m) condensate receiver Op. 24.01.05 Dec. date 08.04.05 - TC 0501205 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8422.30 PACKING MACHINES, flat bed, having integral indexed feed conveyors, which transport pre-formed trays filled with food to an automatic controlled atmosphere packaging and sealing station, having ALL of the following: (a) air evacuation of trays; (b) gas flushing of trays; (c) heat sealing of trays Op. 30.06.89 Dec. date 22.05.90 - TC 8905160 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8422.30.90 APPLICATORS, WAX CAP Op. 01.01.02 Dec. date 09.01.02 - TC 0108770 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8422.30.90 FILLING, CRIMPING, GASSING AND TESTING EQUIPMENT, AEROSOL CONTAINER, capacity greater than 70 cans/min Op. 01.01.02 Dec. date 09.01.02 - TC 0108953 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8422.30.90 LABELLERS, having ALL the following: (a) dual conveying belts; (b) hydraulic label feed with pump and manifold; (c) glue pot and temperature control; (d) pressurised paste applicators; (e) variable speed drive with motor Op. 01.01.02 Dec. date 12.03.02 - TC 0202111 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



8422.30.90 DIAPER BAGGING MACHINES, having ALL of the following: (a) bagging capacity of 49 000 diapers per hour OR greater; (b) bag heat sealer; (c) trim cutter; (d) bag feeder Op. 27.05.02 Dec. date 16.08.02 - TC 0204561 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8422.30.90 TRAY LOADERS, BISCUITS, PLC controlled, having a tray de-nester Op. 30.03.04 Dec. date 09.07.04 - TC 0403301 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8422.30.90 SEALER, COMPOSITE CAN Op. 10.11.04 Dec. date 14.01.05 - TC 0411938 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8422.90.00 PARTS, ROTARY HEAD BOTTLE RINSING MACHINE, the machine having ALL of the following features: (a) ability to rinse internally by nozzle entry in order to remove dust and debris from new containers; (b) rinsing function confined to internal container surfaces only, keeping external surfaces completely dry; (c) containers inverted through 180 degrees by gripping neck and body of glass or plastic bottles with inclined containers transported through a rotary horizontal plane; (d) computer controlled rinsing cycles incorporating air, water or steam or any combination of all three; (e) an effective output greater than 54 000 bottles/h, being ANY of the following: (a) infeed worm; (b) set of bottle handling components, comprising ALL of the following: (i) infeed starwheel; (ii) centre guide; (iii) outfeed starwheel; (c) neck clamps; (d) body clamps Op. 23.10.95 Dec. date 02.02.96 - TC 9511457 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8424.20.00 EDGE TRIMMERS, WATER JET, PAPER AND/OR PAPERBOARD Op. 23.03.05 Dec. date 30.05.05 - TC 0503523 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8424.30.90 PROJECTORS, refractory powder and oxygen mixture Op. 10.12.04 Dec. date 11.02.05 - TC 0413472 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8424.81.00 SPRINKLERS, TURF, POP-UP, having ALL of the following: (a) multiple matrix nozzle configuration of 7 self cleaning port heads; (b) water flow adjustable from 4 L/min to 42.2 L/min; (c) one key adjustment, wet or dry, of arc (where not full circle), trajectory and flow; (d) nozzle stream maintained after any alteration to arc (where not full circle), trajectory and radius Op. 18.10.95 Dec. date 29.01.96 - TC 9511354 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8424.89.90 WASHERS, POULTRY DEFEATHERER, track and shackle Op. 25.10.04 Dec. date 04.01.05 - TC 0411069 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



8424.89.90 CLEANERS, MALT GERMINATOR Op. 04.04.05 Dec. date 10.06.05 - TC 0503932 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8424.89.90 SPRAY ATOMISERS, WATER, MALTING GERMINATOR Op. 06.04.05 Dec. date 17.06.05 - TC 0503968 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8424.90 EXTINGUISHER CYLINDERS, low pressure, thin wall, aluminium, 1 L, 2 L or 3 L capacity, with a minimum burst pressure of 7 MPa Op. 07.01.92 Dec. date 15.04.92 - TC 9200918 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8425.11.00 LONGLINE FISHING MACHINES, having ALL of the following: (a) baiter; (b) line hauler; (c) hook separator; (d) hook cleaner; (e) line retriever; (f) hook storage magazine; (g) bait cutter; (h) line controller Op. 07.05.02 Dec. date 26.07.02 - TC 0203836 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8426.49 CRANES, crawler mounted, 200 t or greater carrying capacity, but NOT including cranes when fitted with the following: (a) luffing jibs; (b) tower crane attachments, which when fitted to a crane do not increase the crane’s lifting capacity Op. 30.08.89 Dec. date 22.01.90 - TC 8906242 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8427.10.00 WORK ASSIST VEHICLES, battery powered, rider stand-on, comprising a mobile load deck with an elevating operator’s platform and loading tray, having ALL of the following: (a) vehicle weight including battery less than 500 kg; (b) max load tray capacity 100 kg; (c) turning radius less than 1 300 mm; (d) load tray lift height of 2.5 m to 3.1 m Op. 11.12.00 Dec. date 09.03.01 - TC 0010048 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8427.10.00 SHUTTLES, MATERIALS HANDLING, unmanned and not pedestrian operated, remote or radio controlled, programmable logic control, lift height NOT exceeding 1.3 m Op. 06.10.04 Dec. date 07.03.05 - TC 0410525 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



8427.20.00 MOVERS, UNIT LOAD, having ALL of the following: (a) self loading and unloading; (b) six OR more independently suspended axles, three OR more per side, each axle having a minimum of two tyres; (c) lifting and carrying capacity in excess of 120 t/unit; (d) self propelled Op. 10.05.01 Dec. date 20.07.01 - TC 0104003 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8428.60.00 ROPEWAYS, PASSENGER MOVING AND/OR CARRYING, complying with the National Standard of Canada, Z98, with or without rope or cable supports, having ALL of the following: (a) cabins or chairs or tee bars; (b) ropes or cables; (c) drive and return terminals Op. 09.08.04 Dec. date 05.11.04 - TC 0408103 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8428.90 FEEDER ASSEMBLIES, dual wire Op. 12.06.84 Dec. date 12.06.84 - TC 8439544 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8428.90.00 ELEVATING WORK PLATFORMS, hydraulically actuated scissor lift, extendable deck, 24V DC electro-hydraulic drive system incorporating solenoid operated positive traction (limited slip) hydraulic drive system, platform control of all functions, capable of travelling with elevated platform and having ALL the following: (a) maximum lifting capacity NOT less than 200 kg; (b) maximum platform height NOT greater than 6.10 m; (c) ability to transverse when elevated and at a maximum speed no greater than 5km/h when collapsed; (d) maximum collapsed height NOT greater than 2.3 m; (e) overall width NOT greater than 1.6 m; (f) maximum gross weight NOT exceeding 2 400 kg; (g) foam filled or solid rubber tyres but NOT including scissor lifts with electrically insulated platforms Op. 06.06.94 Dec. date 28.10.94 - TC 9405026 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8428.90.00 AERIAL WORK PLATFORMS, AC or DC power source, portable, incorporating adjustable outriggers and levelling screw jacks, having ALL of the following: (a) a maximum working height of 7.7 m or greater; (b) a lifting capacity of 110 kg or greater; (c) platform size of 66 cm x 66 cm (d) outrigger footprint length of 166 cm or greater; (e) outrigger footprint width of 150 cm or greater Op. 18.08.95 Dec. date 22.02.96 - TC 9509832 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8428.90.00 UNSCRAMBLERS, LOG HANDLING AND CONVEYING, step feed, self propelled, having BOTH of the following: (a) log length handling capability of NOT greater than 6.5 metres; (b) log diameter handling capability of NOT greater than 905 mm Op. 01.10.03 Dec. date 30.12.03 - TC 0312465 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



8428.90.00 PICKING LINE, PRINT MEDIA, comprising NOT less than ANY three of the following: (a) conveyor belt and buffered roller conveyor (buffered picking line); (b) online delivery note printer; (c) led display; (d) programmable logic controller Op. 21.05.04 Dec. date 30.07.04 - TC 0404923 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8428.90.00 DISTRIBUTOR, ASEPTIC PLASTIC BOTTLES, having ALL of the following: (a) delivery on demand to 8 lanes at 220 bottles per minute; (b) PLC Controlled; (c) bottle in feed conveyor Op. 10.06.04 Dec. date 20.08.04 - TC 0405591 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8428.90.00 UNSCRAMBLER AND ORIENTATOR, ASEPTIC PLASTIC BOTTLES, having of ALL of the following: (a) process aseptic plastic bottles up to and NOT greater than 1 litre; (b) operating capacity greater than 13 150 bottles per hour; (c) photoelectric cell bottle detector Op. 10.06.04 Dec. date 20.08.04 - TC 0405592 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8428.90.00 TRANSFER LINE, PORK BONING, PLC, comprising ALL of the following: (a) transfer trays with transponders; (b) conveyors; (c) tray lifters; (d) inspection and packing tables; (e) tray washer Op. 09.07.04 Dec. date 01.10.04 - TC 0406939 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8428.90.00 COUNTER STACKER, tortilla OR pizza base Op. 29.09.04 Dec. date 10.12.04 - TC 0410261 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8428.90.00 HANDLERS, comprising ALL of the following: (a) tanks; (b) pumps; (c) loading arms; (d) valves Op. 25.10.04 Dec. date 07.01.05 - TC 0411086 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8428.90.00 SHIPPING CASE UNLOADERS, PAPERBOARD CARTON BLANKS, PLC, comprising ALL of the following: (a) rotary turret carton blank extractor; (b) carton stack rotator AND/OR lifter; (c) pressure controlled feeder Op. 11.11.04 Dec. date 21.01.05 - TC 0412029 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8428.90.00 TURRETS, TOOL, ALUMINIUM POT LINE CELL TENDING CRANE Op. 23.11.04 Dec. date 01.02.05 - TC 0412848 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8428.90.00 DRIVE REELS, marine Op. 29.11.04 Dec. date 04.02.05 - TC 0413051 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



8428.90.00 HANDLER AND/OR SORTER, TIMBER, comprising ALL of the following: (a) sorter; (b) board sorter; (c) plc Op. 24.02.05 Dec. date 06.05.05 - TC 0502569 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8428.90.00 LOADERS AND UNLOADERS, KILN Op. 06.04.05 Dec. date 10.06.05 - TC 0503782 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8428.90.00 UNLOADING ARMS, MARINE, LIQUIDS TRANSFER, self-supporting Op. 08.04.05 Dec. date 17.06.05 - TC 0503992 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8429.40 ROLLERS, multi-tyred, having ALL of the following: (a) gross weight NOT exceeding 3 000 kg; (b) maximum overall width NOT exceeding 1 300 mm; (c) tyre size of 9.5/65-15 Op. 03.09.92 Dec. date 14.01.93 - TC 9208062 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8429.40.00 ROLLERS, vibratory compaction, single drum, self propelled, having ALL of the following: (a) operating weight between 2 000 kg and 9 000 kg inclusive; (b) 4 rear pneumatic tyres and single front vibratory drum; (c) hydrostatic travel and vibration drive; (d) dual frequency amplitude and vibration; (e) a working width of between 1 000 and 1 700 mm inclusive; (f) an air cooled diesel engine with a performance of 20-76 kW (SAE) inclusive Op. 24.01.94 Dec. date 05.05.94 - TC 9401482 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8429.51.90 CLEANERS, ANODE CAVITY Op. 11.09.02 Dec. date 06.12.02 - TC 0208416 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8431.39.00 PARTS, PUSH BAR STACKER, Lehr loader, being componentry under the following descriptions: (a) frame; (b) connecting link stabilizer; (c) overarm; (d) push bar support; (e) stabilizer bar; (f) stacker frame (1.8m or 3.04m nominal width); (g) tripper; (h) cam follower support; (i) machine guard; (j) vertical positioner; (k) independent base; (l) tubing conveyor (12.7cm or 15.24cm chain) Op. 08.11.93 Dec. date 04.03.94 - TC 9313112 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



8431.39.00 PARTS, STEEL COIL CONVEYOR, being ANY of the following: (a) conveyor wheels; (b) axles; (c) link bushes Op. 10.06.04 Dec. date 27.08.04 - TC 0405658 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8431.39.00 PARTS, CONTINUOUS ACTION CONVEYOR, being ANY of the following: (a) straight running thermoplastic plate top chain platforms; (b) side flexing thermoplastic plate top chain platforms Op. 14.07.04 Dec. date 20.09.04 - TC 0407066 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8433.59 HARVESTERS, tomato Op. 01.07.83 Dec. date 01.07.83 - TC 8333351 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8433.59.90 ALMOND HARVESTER Op. 27.12.94 Dec. date 07.04.95 - TC 9500450 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8433.90.90 PARTS, ALMOND HARVESTER, being ANY of the following: (a) dirt chain; (b) pickup belt; (c) wearstrips; (d) stickbreakers; (e) pickup fan blades; (f) fan liners Op. 28.02.96 Dec. date 21.06.96 - TC 9603923 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8434.20.00 COOKING AND STRETCHING MACHINES, MOZZARELLA CHEESE Op. 19.12.03 Dec. date 31.03.04 - TC 0315746 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8436.80 COMPOST TURNERS, mushroom, having a turning capacity of 80 t/h or greater Op. 18.11.83 Dec. date 23.02.84 - TC 8334899 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8436.80.90 MOBILE GULLIES, GREENHOUSE, PLC, comprising ALL of the following: (a) growing gullies; (b) ratchet conveyor; (c) motor Op. 18.10.04 Dec. date 07.01.05 - TC 0410875 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8438.10 MIXERS, dough, having ALL of the following: (a) planetary action; (b) spiral action; (c) dough capacity/batch exceeding 599 kg; (d) dough discharge from power operated door opening at end of mixer Op. 28.10.85 Dec. date 24.02.86 - TC 8534821 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8438.10.90 PROCESSING LINES, PIZZA TOPPING Op. 27.08.01 Dec. date 09.11.01 - TC 0107578 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



8438.10.90 MIXING AND PROOFING LINES, DOUGH, computer controlled, having a capacity exceeding 1 750 kg per hour and comprising ALL of the following: (a) mixer; (b) dough feeder; (c) metal detector; (d) proofer Op. 12.10.01 Dec. date 28.12.01 - TC 0109279 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8438.20.00 MOULD FILLERS, ICE CONFECTIONERY Op. 08.09.04 Dec. date 15.11.04 - TC 0409164 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8438.40.00 TURNER AND/OR LOADER AND/OR UNLOADER, MALT GERMINATOR AND/OR KILN Op. 01.04.05 Dec. date 10.06.05 - TC 0503927 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8438.50.00 SEPARATING MACHINES, SAUSAGE Op. 12.08.98 Dec. date 23.10.98 - TC 9807121 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8438.60.00 PECAN NUT PROCESSING LINES, comprising All of the following: (a) sizer elevator; (b) inshell sizer; (c) cracker; (d) bucket elevator; (e) sheller; (f) vacuum separator; (g) packaging table Op. 21.08.03 Dec. date 17.11.03 - TC 0310383 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8438.60.00 HALVERS, PUMPKIN, with rotating screen Op. 14.09.04 Dec. date 22.11.04 - TC 0409373 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8438.80.00 EXTRUSION COOKERS, SOLID PELLETISED DOG FOOD PRODUCTION, having variable speed feeding Op. 08.05.00 Dec. date 28.07.00 - TC 0004594 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8438.80.00 BAKING LINE, ICE CREAM SUGAR CONE, capacity NOT less than 5 000 units/h, having BOTH of the following: (a) baking oven incorporating individual cast iron baking tongs; (b) revolving roller Op. 28.06.00 Dec. date 01.09.00 - TC 0005806 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8438.80.00 MIXERS, FOOD, VACUUM, pneumatic lid opening, having a capacity of 590 litres OR greater Op. 25.05.01 Dec. date 10.08.01 - TC 0104332 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



8438.80.00 FOOD PREPARATION, FILLING, SEALING AND PACKAGING LINE, comprising ALL of the following: (a) starch bag hanger; (b) cooker; (c) conveyors; (d) denestor; (e) bowl inspector; (f) food depositors; (g) sauce dispenser; (h) multi-head weigher; (i) bowl sealer; (j) check weigher; (k) bowl merging combiner; (l) case packer Op. 29.06.04 Dec. date 03.09.04 - TC 0406498 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8438.90.10 PARTS, TURNER AND LOADER AND UNLOADER, being turning screws Op. 06.04.05 Dec. date 10.06.05 - TC 0503781 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8439.99 HEADBOXES, step diffusor, hydraulic Op. 12.04.84 Dec. date 09.07.84 - TC 8431551 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8439.99.00 PARTS, HEAD BOX, width NOT less than 6 m, being EITHER of the following: (a) apron lips; (b) tapered inlet header Op. 09.08.04 Dec. date 29.10.04 - TC 0408106 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8441.10.10 SLITTING MACHINE, surface wind, having ALL of the following: (a) maximum web width 1 450 mm; (b) maximum unwind diameter 1 525 mm; (c) maximum speed 700 m/min; (d) shaftless dual turret unwind, roll weight 3 100 kg maximum; (e) rewind core loading and tapeless cinch start; (f) square web cut off; (g) finished roll removal; (h) finished roll closure; (i) cycle time of less than 45 s for a 176 m roll Op. 18.03.96 Dec. date 28.06.96 - TC 9604765 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8451.80.00 TEXTILE FINISHING MACHINERY, being EITHER of the following: (a) blade over roll, blade over air coating head; (b) double dosing head flocker with conveyor belt Op. 08.11.02 Dec. date 31.01.03 - TC 0210641 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8451.80.00 SUEDERS, TEXTILE FABRIC Op. 30.06.04 Dec. date 24.09.04 - TC 0406606 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8451.80.00 TEXTILE FABRIC ADHESIVE COATER AND LAMINATOR, with drum melter Op. 08.10.04 Dec. date 20.12.04 - TC 0410597 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



8451.90 WIRE, angled brushing, backed with felt, canvas or rubber Op. 02.08.89 Dec. date 23.04.90 - TC 8905501 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8454.90.00 LAMELLA SUSPENSION, STEEL MAKING PLANT, BASIC OXYGEN STEEL CONVERTOR VESSEL Op. 09.09.04 Dec. date 22.11.04 - TC 0409192 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8462.29 MITRING MACHINES, steel rule, hand operated Op. 04.09.84 Dec. date 04.09.84 - TC 8434493 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8465.10.00 TIMBER PROCESSING PLANT, comprising ALL of the following: (a) log bucker; (b) reducer twin; (c) horizontal resaw; (d) twin band resaw; (e) gang edger; (f) optimised board edger; (g) trimmer line; (h) saw fling; (i) chipper; (j) conveyor Op. 24.02.05 Dec. date 06.05.05 - TC 0502570 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8465.91.00 SAWING MACHINES, TRIMMING, OPTIMISING, having ALL of the following: (a) infra red laser solid state surface scanner; (b) programmable logic control; (c) operator workstation Op. 13.12.99 Dec. date 03.03.00 - TC 9910008 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8465.99 LATHES, woodworking, rotary knife, interchangeable cutter head Op. 20.11.85 Dec. date 20.11.85 - TC 8535160 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8466.92.00 PARTS, LOG SAWMILLING LINE, being ANY of the following: (a) bladeless band saws; (b) bladeless circular saw end trimmers; (c) bladeless edgers; (d) PLC transfer Op. 20.08.04 Dec. date 29.10.04 - TC 0408577 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8474.20.00 SEMI-AUTOGENOUS GRINDING LINE, comprising ALL of the following: (a) storage and discharge tanks; (b) apron feeder and drive; (c) mill feed conveyor; (d) semi-autogenous grinding mill; (e) hoppers; (f) pumps; (g) sumps Op. 07.07.04 Dec. date 24.09.04 - TC 0406872 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



8474.80.00 PRESSURE CASTING PLANT, SANITARY WARE, slip, comprising caster benches and demoulders, having ANY of the following: (a) process control cabinet; (b) electrical distribution cabinet; (c) pneumatic switch cabinet; (d) work piece lifters; (e) work piece racks; (f) work piece handlers and work piece finishers; (g) finishing tables; (h) conveyors; (i) tool racks; (j) pressure vessels; (k) slip manifolds; (l) water tanks; (m) water filters; (n) electro-mechanical safety barriers; (o) robot pedestals; (p) gripper racks; (q) date stamper; (r) electrical trunking; (s) pumps; (t) air compressors; (u) hydraulic power unit; (v) hydraulic rams; (w) valves; (x) mould frames Op. 27.09.04 Dec. date 04.01.05 - TC 0410179 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8474.90.00 DIES, TILE PUNCH, having a moulded urethane surface Op. 09.10.98 Dec. date 18.12.98 - TC 9809100 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8477.59.00 HYDRAULIC PRESS, PLASTIC, having BOTH of the following: (a) conveyor oven; (b) press closure rate of NOT less than 800 mm per second at NOT less than 2 500 tonnes Op. 15.11.04 Dec. date 01.02.05 - TC 0412267 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8477.80 CUTTING MACHINES, synchronised precision type, with combined haul off and dual cutters, capable of on demand and rotary cutting of plastic tubes and sections Op. 24.09.84 Dec. date 28.06.85 - TC 8433095 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8477.80.00 PELLETISING LINES, comprising BOTH of the following: (a) crystallisator; (b) solid state polycondensator Op. 12.10.04 Dec. date 20.12.04 - TC 0410703 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8477.80.00 EXTRUSION LINES, thermoplastic, plc, single screw, comprising ALL of the following: (a) feeder and volumetric doser with mixer; (b) extruder with thermo-regulator; (c) continuous flow hydraulic filters; (d) single outlet metering pumps; (e) die heads; (f) formers Op. 01.12.04 Dec. date 11.02.05 - TC 0412880 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



8477.80.00 PELLETISING MACHINES, underwater die face cutter type but NOT including such pelletising machines when imported with single screw extruders Op. 06.12.04 Dec. date 07.12.04 - TC 0413136 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8477.80.00 EXTRUSION LINE, PLASTIC PIPE, comprising ALL of the following: (a) extruder; (b) pipe head; (c) vacuum calibration tank; (d) cooling tank; (e) haul off; (f) cut off saw; (g) outside diameter NOT less than 250 mm Op. 18.02.05 Dec. date 06.05.05 - TC 0502230 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8479.82 SKIVERS, belt Op. 05.06.84 Dec. date 05.06.84 - TC 8439135 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8479.82.00 MILLS, BALL, COLLOIDAL Op. 23.01.02 Dec. date 12.04.02 - TC 0200773 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8479.82.00 MIXERS, PHARMACEUTICAL, computer controlled Op. 08.02.02 Dec. date 26.04.02 - TC 0201212 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8479.82.00 GRINDERS, HORIZONTAL, ROTARY, having ALL of the following: (a) two OR three axle trailer; (b) direct drive grinder having drum diameter NOT less than 75 cm and NOT greater than 80 cm; (c) grinder input throat NOT less than 65 cm and NOT greater than 70 cm; (d) motor rating NOT less than 90 kW and NOT greater than 100 kW; (e) screen sizes NOT less than 2.5cm and NOT greater than 10.2 cm Op. 25.08.04 Dec. date 05.11.04 - TC 0408736 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8479.89 SYNTHESIZERS, biomolecule sample, laboratory type Op. 09.05.85 Dec. date 07.11.85 - TC 8534854 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8479.89 PRESSES, attaching, footwear sole Op. 10.03.88 Dec. date 14.07.88 - TC 8802599 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8479.89 HARVESTERS, biological culture Op. 13.12.88 Dec. date 06.07.89 - TC 8900070 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8479.89 ACTUATORS, linear, powered by an oscillating electrohydraulic pump NOT exceeding 30 watts Op. 31.10.88 Dec. date 03.06.93 - TC 9300345 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



8479.89.90 CLEANERS, duct auger, flexible rotating shaft cleaning head, capable of loosening debris in ducting up to 30 metres from access point Op. 01.07.93 Dec. date 08.11.93 - TC 9304752 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8479.89.90 DISPENSERS, QUEUING TICKETS, having an integral cutting blade Op. 03.08.98 Dec. date 16.10.98 - TC 9806847 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8479.89.90 BRAKES, DISC, with OR without integrated power unit, having ALL of the following: (a) spring applied hydraulic release OR pressure applied; (b) braking force of 9 500 N OR greater per caliper; (c) disc size exceeding 600 mm in diameter and 20 mm in thickness Op. 20.11.98 Dec. date 05.02.99 - TC 9810217 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8479.89.90 POSTFORMING MACHINES, comprising ALL of the following: (a) sizer; (b) glue applicator; (c) glue activator; (d) bender; (e) finish processor; (f) contactless temperature measurer Op. 26.10.99 Dec. date 05.01.00 - TC 9908100 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8479.89.90 DISPLAYS, SHELF, advertising, changing image Op. 05.09.00 Dec. date 17.11.00 - TC 0007651 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8479.89.90 SKIVING MACHINES, ABRASIVE BELT Op. 10.11.00 Dec. date 19.01.01 - TC 0009333 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8479.89.90 BONDING MACHINES, DVD (DIGITAL VERSATILE DISC), having ALL of the following: (a) ultra violet glue dispensers; (b) sandwich spinners; (c) ultra violet curing light Op. 11.09.01 Dec. date 30.11.01 - TC 0108048 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8479.89.90 TAMPON MAKING MACHINE Op. 29.10.02 Dec. date 21.01.03 - TC 0210189 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8479.89.90 FALL PROTECTION SYSTEMS, having ANY of the following: (a) anodised aluminium safety climbing frames; (b) hot dipped galvanised steel safety climbing frames; (c) pickled stainless steel safety climbing frames; and ALL of the following: (i) travelling fall arrestors; (ii) end stops; (iii) mounting brackets Op. 14.02.03 Dec. date 16.05.03 - TC 0301539 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



8479.89.90 GLAZE LINES, CERAMIC TILE, comprising ALL of the following: (a) glazing application pump; (b) dust tractor; (c) electrical controls Op. 26.09.03 Dec. date 19.12.03 - TC 0312276 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8479.89.90 CLEANING, SKIMMING, CHARGING AND STIRRING MACHINES, HOLDING OR BATCH FURNACE, mobile, comprising ALL of the following: (a) slewing upper frame; (b) telescopic boom; (c) interchangeable blades; (d) multi function joy stick control Op. 30.09.03 Dec. date 30.12.03 - TC 0312448 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8479.89.90 INSULATED GLASS SHEET PRODUCTION LINE, comprising ALL of the following: (a) edge deletion machine; (b) washing and drying machine; (c) frame mounter; (d) assembler and presser; (e) sealing robot; (f) butyl coating machine Op. 10.10.03 Dec. date 02.01.04 - TC 0312810 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8479.89.90 PORT CLEANING SYSTEM, CHEMICAL RECOVERY BOILER, comprising ALL of the following: (a) cleaning rods; (b) air cylinder drive; (c) indexing clutches; (d) PLC controlled Op. 18.03.04 Dec. date 15.06.04 - TC 0402845 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8479.89.90 FINISHERS, ZIP FASTENER, being ANY of the following: (a) chain spacers; (b) tape attachers; (c) zipper piercers and cutters; (d) stop and open section injectors; (e) box attachers; (f) tape cutters Op. 22.04.04 Dec. date 23.07.04 - TC 0403998 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8479.89.90 PANT LINER MACHINES Op. 10.06.04 Dec. date 27.08.04 - TC 0405596 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8479.89.90 LOADERS, articulated, four wheel drive, having ALL of the following: (a) net SAE engine power of EITHER 27 kW or 35 kW; (b) maximum operating weight of EITHER 3 580 kg or 4 460 kg; (c) 100% differential locks in both axles but NOT including loaders imported with buckets, backhoe loader sections or other attachments Op. 28.06.04 Dec. date 07.07.04 - TC 0406692 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



8479.89.90 LOADERS, articulated, four wheel drive, having ALL the following: (a) maximum operating weight 2 050 kg; (b) gross engine power 22 kW; (c) 100% differential locks in both axles but NOT including loaders imported with buckets, backhoe loader sections or other attachments Op. 28.06.04 Dec. date 07.07.04 - TC 0406693 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8479.89.90 SORTING, SEPARATING AND PROCESSING PLANT, MIXED COLOURED GLASS, comprising ALL of the following: (a) glass colour sorters and separators; (b) resonance vibratory screens; (c) roller crushers; (d) linear screening vibratory feeders; (e) infeed vibratory feeders Op. 09.07.04 Dec. date 24.09.04 - TC 0406938 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8479.89.90 PRECIPITATION PLANTS, BAUXITE SLURRY, comprising ALL of the following: (a) gravity separators; (b) seed filters; (c) heat exchangers Op. 02.09.04 Dec. date 15.11.04 - TC 0409023 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8479.89.90 PLANTS, BAUXITE REMOVAL, bauxite processing, comprising ALL of the following: (a) cyclones; (b) counter-current wash towers; (c) thickeners Op. 30.09.04 Dec. date 10.12.04 - TC 0410405 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8479.89.90 WASTE GLASS SEPARATING AND SORTING LINE, comprising ALL of the following: (a) non-glass rejectors; (b) glass colour sorters; (c) resonance vibratory screens; (d) grading feeder and glass transportation conveyors Op. 01.11.04 Dec. date 07.01.05 - TC 0411310 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8479.89.90 COATING AND/OR DRYING LINE, plc, comprising ALL of the following: (a) centrifugal dryers; (b) transfer hoists; (c) steel baskets; (d) hoist tracks; (e) basket unloaders Op. 10.01.05 Dec. date 29.03.05 - TC 0500568 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8479.90 PLATES, hardboard press Op. 15.07.87 Dec. date 12.10.87 - TC 8734041 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8480.60.00 DIE MOULDS AND PUNCHES, having ANY of the following: (a) heating electrical resistance; (b) hardened steel lining plates; (c) upper punches Op. 26.09.03 Dec. date 12.12.03 - TC 0312277 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



8481.10 REGULATORS, gas, pilot operated, sizes 25 mm OR 50 mm, maximum inlet pressure 9.6 MPa, outlet pressure range 69.0 kPa or greater but NOT exceeding 4.1 MPa Op. 12.06.84 Dec. date 12.06.84 - TC 8438628 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8481.80 VALVES, GAS, obturating poppet, temperature modulating self-contained non-electrical type, capable of maintaining a preset temperature constant within the range 16 degrees C to 116 degrees C (both inclusive) and having BOTH of the following characteristics: (a) capacity of 7.1 cu m/h or greater but NOT exceeding 13.7 cu m/h; (b) a maximum pressure rating of 3.5 kPa Op. 30.12.85 Dec. date 01.04.86 - TC 8435115 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8481.80.90 VALVE CORE, AIRCONDITIONING CHARGING VALVE, having ALL of the following: (a) return spring; (b) bridge; (c) plug; (d) plug washer; (e) plunger washer; (f) pincup Op. 26.07.95 Dec. date 17.11.95 - TC 9509215 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8481.80.90 VALVES, FIRE EXTINGUISHING, gas, having ALL of the following: (a) actuated electrically, pneumatically and/or manually; (b) self slaving; (c) complying with AS4214.2 Op. 09.02.96 Dec. date 31.05.96 - TC 9603077 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8481.80.90 CONTROL VALVES, having ALL of the following: (a) PTFE based thermo plastic composite internal housing, size range 15 mm to 40 mm (both inclusive); (b) ported inlet and outlet; (c) adjustable to at least 50 different flow settings; (d) stainless steel upper and lower springs; (e) hydrogenated acrylonitrile butadeine rubber rolling diaphragm; (f) dezincification resistant brass valve body; (g) 1/8" pressure/temperature test plugs; (h) operating temperature range from -30 degrees C to 120 degrees C (both inclusive); (i) balancing accuracy of + or - 5% Op. 10.10.96 Dec. date 20.12.96 - TC 9611360 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8481.80.90 VALVES, MIXING, THERMOSTATIC AND PRESSURE BALANCING CONTROL, conforming to AS 1357.2 having ALL of the following: (a) free floating piston; (b) single cartridge; (c) wax filled thermostat Op. 28.01.97 Dec. date 28.04.97 - TC 9700757 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8481.80.90 VALVES, HOT BLAST STOVE SHUT-OFF Op. 07.02.05 Dec. date 18.04.05 - TC 0501480 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



8481.90.90 PARTS, DIRECT SOLENOID OR EXTERNALLY CONTROLLED POSITIVE SEAL OBTURATING ELEMENT VALVE, being ANY of the following: (a) seats; (b) seals; (c) magnets Op. 10.12.97 Dec. date 27.02.98 - TC 9710921 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8481.90.90 VALVE CHAMBERS, BLAST FURNACE VALVE Op. 25.08.04 Dec. date 29.10.04 - TC 0408737 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8481.90.90 SHAFT, BLAST FURNACE EQUALISING AND RELIEF VALVE Op. 01.02.05 Dec. date 08.04.05 - TC 0501344 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8483.10.99 CRANK DISCS, electro pneumatic hammer Op. 01.07.93 Dec. date 24.02.94 - TC 9330379 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8483.40.19 GEAR TRAIN ASSEMBIES, TURBINE OIL PUMP, consisting of ALL of the following: (a) torsion rod; (b) gear wheel; (c) pinion shaft; (d) bearings; (e) shim Op. 03.08.04 Dec. date 25.10.04 - TC 0407956 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8483.40.90 TRANSAXLES, differential automotive bevel gears, having ALL of the following: (a) torque output of 203.37Nm (150 ft lbs); (b) die cast aluminium housings; (c) oil impregnated bushings; (d) needle bearings on input shaft; (e) 5 forward gears and 1 reverse gear Op. 07.07.94 Dec. date 14.10.94 - TC 9406003 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8483.40.90 DRIVES, CONVEYOR, comprising ALL the following: (a) gears; (b) couplings; (c) brakes; but NOT including: (a) chains; (b) sprockets Op. 16.12.02 Dec. date 14.03.03 - TC 0211886 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8483.40.90 HELICAL GEARS, PRIMARY, comprising BOTH of the following: (a) crown gear, with a gear center NOT greater than 165 mm; (b) pinion Op. 28.04.03 Dec. date 21.07.03 - TC 0304750 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



8483.60.90 COUPLING SYSTEM, single and double-acting, having ALL of the following: (a) maximum operating pressure of 500 bar; (b) double check valve; (c) radial misalignment adjustment of + or - 0.5 mm; (d) axial misalignment adjustment of + or - 1 mm Op. 05.04.96 Dec. date 29.07.96 - TC 9605448 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8483.90.00 ADAPTORS, ELECTRIC MOTOR TO GEARBOX, having BOTH of the following: (a) internal half moon shaped bushing on one side; (b) carbon fibre mounting Op. 04.04.03 Dec. date 20.06.03 - TC 0303714 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8501.10 MOTORS, DC, oscillating, voltage rating NOT exceeding 3 V DC Op. 16.12.86 Dec. date 26.05.87 - TC 8636234 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8501.33.00 MOTORS, DC, totally enclosed fan cooled (TEFC) mill type, constant drive speed, but NOT including replacement coils or bars therefor Op. 28.06.94 Dec. date 18.01.95 - TC 9500337 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8501.34.00 MOTORS, DC, armoured, 779 kW continuous rating, 475 V, 1 760 A, 740 rpm Op. 18.06.99 Dec. date 03.09.99 - TC 9904516 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8501.34.00 MOTORS, DC, water and/OR air cooled, having ALL of the following: (a) output 650 kW OR greater; (b) speed within the range 675 rpm - 1 250 rpm; (c) armature voltage within the range 550 volts - 650 volts Op. 26.02.02 Dec. date 17.05.02 - TC 0201741 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8501.34.00 DC MOTORS, having BOTH of the following: (a) power greater than 900 kW; (b) rated current greater than 2 300 amps Op. 11.02.05 Dec. date 22.04.05 - TC 0501737 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8502.20.00 GENERATORS, AC/DC, portable, brushless 2 pole, powered by a 4 stroke air cooled 93 cc spark ignition internal combustion piston engine, having ALL of the following: (a) AC rated output at 240 V 50 Hz of 600 W continuous, maximum 700 W; (b) DC rated output 12 V, 8 A (8.3 A maximum), 100 W; (c) weight NOT exceeding 21 kg Op. 18.11.94 Dec. date 03.03.95 - TC 9409088 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



8503.00.00 POLES, ROTATING ELEMENT, AC GENERATOR, NOT less than 20 MW Op. 14.01.05 Dec. date 29.03.05 - TC 0500569 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8504.22.00 TRANSFORMERS, MAIN, comprising ALL of the following: (a) single phase; (b) oil cooled; (c) voltage NOT less than 4.5 MVA; (d) frequency NOT less than 25 kVA; (e) power output NOT less than 50 Hz; (f) windings; (g) circulating pumps; (h) piping with valves; (i) monitors Op. 26.10.04 Dec. date 30.11.04 - TC 0412963 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8504.40.90 VIDEO CAMERA KITS, comprising ALL of the following: (a) accumulators, lithium ion, with permanently sealed cases; (b) chargers or adapters, battery, input voltage 240 V AC + or - 10%, output voltage 8 V DC + or - 2 V; (c) battery pouch Op. 03.09.98 Dec. date 03.12.99 - TC 9907823 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8507.20.00 ACCUMULATORS, LEAD ACID, having ALL of the following: (a) output voltage of 48 V DC; (b) capacity of 17 AH; (c) maximum dimensions of 250 mm x 200 mm x 500 mm; (d) maximum weight of 35 kg Op. 21.12.98 Dec. date 19.03.99 - TC 9810975 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8516.79.00 STEAM FACIAL MASKS, MOISTURISING, contoured to fit the face Op. 10.07.98 Dec. date 13.10.98 - TC 9806043 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8516.79.00 LABORATORY HEATERS AND BLOWERS, having an electronically controlled temperature Op. 16.01.04 Dec. date 13.04.04 - TC 0400760 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8518.29.90 TWEETERS, 25 mm diameter voice coil, having BOTH of the following features: (a) polyamide dome; (b) ferro-fluid Op. 01.07.97 Dec. date 01.07.97 - TC 9703733 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



8529.90 DELAY LINES, PAL Op. 10.04.84 Dec. date 10.04.84 - TC 8438028 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8529.90 TUNER PARTS, being electronic modules as follows: (a) AM varactor modules; (b) FM varactor modules Op. 31.05.89 Dec. date 12.09.90 - TC 8904196 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8531.10 SECURITY EQUIPMENT, electronic fence Op. 08.05.84 Dec. date 08.05.84 - TC 8438283 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8531.90 SECURITY EQUIPMENT, fence protection, incorporating dual channel signal processor combined with 4 conductor magnetic sensor cable Op. 21.05.92 Dec. date 05.11.92 - TC 9205061 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8535.90.00 POWER CABLE TERMINATIONS, GAS FILLED Op. 03.04.01 Dec. date 08.06.01 - TC 0102861 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8536.20.00 CIRCUIT BREAKERS, moulded case, electronically operated, rated current between 250 A and 2 500 A (both inclusive) 3 or 4 pole, having at least three of the following: (a) adjustable long time delay trip; (b) adjustable short time delay trip; (c) adjustable instantaneous trip; (d) adjustable ground fault trip; (e) adjustable pre-trip alarm; (f) adjustable rated current from 50-100% of the nominated rated current, adjustable in 6 or more steps Op. 16.12.94 Dec. date 06.04.95 - TC 9500297 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8536.50.99 REVERSERS, DC TRACTION CIRCUIT, being electrically controlled pneumatic switches Op. 21.11.97 Dec. date 06.02.98 - TC 9710257 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8536.61 LAMP HOLDERS, ceramic, Edison screw, having a minor (inner) thread dia NOT exceeding 13 mm Op. 24.10.86 Dec. date 08.05.87 - TC 8635922 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8536.69.90 CONNECTORS, electrical springwire, multiple free floating springwires at each contact point, mating cycles in excess of 1 000 000 Op. 01.07.97 Dec. date 01.07.97 - TC 9703872 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8705.90.00 SWEEPERS, SUCTION COLLECTION, ride on, diesel powered, comprising ALL of the following: (a) hopper capacity 0.24 cubic metres (240 litres); (b) sweeping width between 120 cm and 160 cm; (c) maximum speed 16 km/h Op. 08.07.04 Dec. date 13.07.04 - TC 0406972 Revoked 2 years non-use. In transit provisions apply

50 31.10.07



8705.90.00 BROADCAST TRANSMISSION VEHICLES, gross vehicle weight NOT greater than 4.5 tonnes, having ALL of the following: (a) roof mounted motorised antennas; (b) radio frequency amplifiers; (c) video AND/OR audio modulators; (d) vehicle stabilising jacks Op. 11.03.05 Dec. date 20.05.05 - TC 0503077 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8716.90.00 UNMACHINED SEMI-TRAILER AXLE SPINDLE FORGINGS, having a hollow centre and being heat treated Op. 13.09.93 Dec. date 04.03.94 - TC 9310174 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

8716.90.00 HITCHES, WEIGHT DISTRIBUTION, having a minimum ball weight capacity of 150 kg, incorporating dual cam or friction sway control devices Op. 23.12.97 Dec. date 13.03.98 - TC 9711263 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

9004.90.00 SWIM SETS, comprising goggles, latex cap, ear AND/OR nose plugs Op. 02.03.94 Dec. date 17.06.94 - TC 9403513 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

9010.60 TRANSFER UNITS, film to video Op. 01.07.96 Dec. date 25.03.96 - TC 9602632 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

9029.10 ODOMETERS, capable of being switched to forward or reverse counting irrespective of vehicle"s direction of travel, incorporating counters reading to 2 decimal places Op. 02.07.85 Dec. date 08.10.85 - TC 8533060 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

9306.30 CARTRIDGE CASES, empty, primed rimfire minimum maximum calibre case length case length metric (imperial) metric (imperial) .22 10.54 mm (.415) 21.11 mm (.831) .25 22.098 mm (.870) 22.22 mm (.875) 6.3 10.54 mm (.415) 16 mm (.630) Op. 11.07.91 Dec. date 26.09.91 - TC 9106420 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

9402.90.00 TROLLEY, medical, having ALL the features listed in table A, whether or not having ANY of those features listed in table B: Table A (a) lightweight polymer construction (b) brake and directional controlled steering; (c) protective buffer system; (d) dedicated storage system comprising interchangeable drawers and bins; (e) individual section central locking system; (f) interchangeable colour coding system; (g) integrated wall locking system Table B (a) cup dispenser, waste disposal system and sharps disposal unit; (b) electronic locking and alarm system; (c) signal dot patient distribution acquittal system; (d) varied dispensing (packaging) system Op. 22.07.94 Dec. date 04.11.94 - TC 9406281 Revoked 2 years non-use. In transit provisions apply

50 31.10.07

Customs Review of TCO Applications Notification

Documents

Commonwealth of Australia Gazette - · PDF fileStated Use: Transfer of liquefied petroleum gas (LPG) ... Outlet for liquids held in storage tanks : ... Stated Use: Used to apply chemical