COMMERCIAL MICRO MANUFACTURINGINTERNATIONAL

THE MAGAZINEFOR MICRO,

HIGH-PRECISION ANDMEMS MANUFACTURERS

1018

in this issuePRODUCTS INSPIRED BY NATURECO LASERSCARRIER WAFERS COMS 2018 REVIEW

articlea

CARSTEN WESSELKAMP, SALES MANAGER, AND MARKUS WAGNER, MARKETING MANAGER, PLAN OPTIK

The carrier wafer— a useful and necessary tool for

MEMS and sensor packaging

MEMS and sensor packaging processes can require the handling and processing of ultra-thin semiconductor wafers. Various thin wafer handling systems that require a special handling tool such as a carrier wafer (or support wafer) are already established in the market. By temporarily bonding a device wafer to a carrier wafer, it can be safely handled and processed. Depending on the temporary bonding and de-bonding techniques, there are di� erent requirements for carrier wafers. This article details the requirements for carrier wafers as a necessary handling tool for 3D wafer level packaging technologies.

Introduction

There is ongoing wafer thickness reduction in the MEMS and semiconductor industry. This is because of market demand for smaller devices that a� ord an increased number of functionalities at reduced cost; and for this, smaller package sizes need to be realised. It is mainly consumer applications that are responsible for this trend, but the demand for smaller package sizes is also attributable to technical advantages, for example better electrical performance or improved thermal management.

Smaller package sizes require extremely thin substrates to build up devices. Those thin and ultra-thin substrates also enable 3D packaging of sensors such as complementary

metal-oxide-semiconductor (CMOS) image sensors and others. Producing thin wafers in high quantities puts challenging requirements on handling and processing tools.

Due to their low thickness, thin wafers are vulnerable to stress and breakage. Warping of the wafers during handling and processing causes a high yield loss or can even make it impossible to handle the wafers any more. This means that a thin wafer handling technology with a high degree of fl exibility on wafer and substrate sizes is needed. Carrier wafers need to have certain properties, such as: mechanical robustness; chemical and high-temperature resistance; incredibly low tolerances (down to 1 μm thickness variation); and thermal expansion adjusted to the used material, for example, gallium arsenide (GaAs), Indium phosphide (InP), silicon (Si) or silicon carbide (SiC). Furthermore, handling tools sometimes need to be suitable for materials such as GaAs and Si, or even CMOS compatible.

High-end carrier wafers made of glass, quartz or silicon can meet the aforementioned requirements. Glass and quartz are excellent materials for carrier wafers because of their thermal stability and resistance against acids and other chemicals. Bonding to and de-bonding from glass and quartz carrier wafers can be monitored since they are transparent. Furthermore, glass carrier wafers can be cleaned

34

commercial micro manufacturing international Vol 11 No. 6 35

article a

Photo-etching delivers metal parts other manufacturers can’t Where our competitors fail, we excel; developing new production methodologies in partnership with our global customer base to ease manufacturing and ultimately reduce their cost.

...and we do it to exacting tolerances, often not achievable with conventional machining.

To create even smaller, even finer components, we combine photo-etching with laser direct imaging, additive layer techniques and fine-wire EDM.

This means ultra-light and complex, burr and stress-free components to 10µm accuracy — from virtually any metal.

Using digital tooling, design iterations are possible in days, not weeks, without incurring excessive cost.

Once the perfect prototype has been developed, we have the capacity to move seamlessly from development to true high volume production - and all from the very same tooling.

Think big with Precision Micro.+44 121 380 0100info@precisionmicro.com

and re-used, thus contributing to cost reduction and environmental protection.

Thin wafer handling

In thin wafer handling processes, the device wafer is temporarily bonded to a rigid carrier wafer of high accuracy using a polymer-based adhesive. The general process fl ow for temporary bonding is shown in fi gure 1. After handling and processing the device wafer using standard semiconductor process tools, the release (debonding) is carried out by way of various

techniques, namely chemicals dissolving the adhesive, heat decreasing the viscosity of the adhesive or laser reducing the adhesive force.

Debonding methods—suitable carriers for di� erent applications

In temporary wafer bonding processes, the carrier wafer needs to be removed from the device wafer at the end of processing. Depending on the device characteristics and the process used, there are di� erent specifi cation requirements for carrier

⊲ Figure 1:General process flow of temporary wafer bonding. ⊲

mailto:info@precisionmicro.com

36

articlea

⊲ Figure 2:Laser release debonding. ⊲

⊲ Figure 3:Chemical release

debonding. ⊲

⊲ Figure 4:Thermal debonding.⊲

Carrier wafer with through holes for chemical debonding.

commercial micro manufacturing international Vol 11 No. 6 37

article a

n Ceramic Injection Molding n Net Shape Process n Micro Tolerances n High Strength n Bio-Compatible n Chemically Inert

Small Precision Tools Inc.Petaluma, CA 94954, USAT +1 707 765 4545cim-usa@spt.net

SPT Roth Ltd3250 Lyss, SwitzerlandT +41 32 387 80 80cim-ch@spt.net

>> www.spt.net/cim

Customized fine ceramic solutions for medical, dental, industrial and electronic markets.

Micro SizeUltra Precision

wafers. Di� erent types of carrier wafers with special properties for common debonding processes are explained below.

Carrier wafers for laser release

In laser debonding, the adhesive strength is reduced by exposing it to laser light (fi gure 2). Debonding methods can be carried out at room temperature.

For laser debonding processes, highly transparent carrier wafers that transmit the relevant laser wavelength are needed. Double-side polished glass or quartz carrier wafers have excellent surface quality and thus meet the requirements of a laser debonding process. After laser exposure, the device wafer can be detached from the carrier wafer. Finally, the carrier wafer needs to be cleaned and can then be re-used several times. The laser debonding method is mainly used in the fan-out wafer-level packaging and advanced packaging processes.

Carrier wafers for chemical release

Here, the de-bonding is caused by chemicals that dissolve the adhesive after processing (including thinning) of the device wafer (fi gure 3). The carrier wafer is perforated to enable the solvent to pass through it and come into contact with the adhesive. Such carrier wafers can be produced by combining a blank glass carrier with the latest patterning technologies and tight tolerances. To be able to distribute the chemistry as fast as possible, extremely small holes with a high density are needed. More than 150,000 through holes of equal size can be created, which a� ords smooth and safe debonding whilst the carrier wafer withstands mechanical infl uences.

Carrier wafers for chemical release are available at a total thickness variation (TTV) as low as 1 micron and in many coe� cient of linear thermal expansion (CTE) adapted materials. These carrier wafers can be re-used up to 50 times.

Carrier wafers for thermal release

Thermoplastic adhesives are used for bonding the device wafer or single chips to the carrier wafer. These adhesives decrease in viscosity at higher temperatures (i.e. from 100˚C), so that having undergone a heating process, the device wafer can be sheared from the carrier wafer (fi gure 4). For this, imperforated carrier wafers or carrier wafers with recessed pockets are needed.

mailto:cim-usa@spt.netmailto:cim-ch@spt.nethttp://www.spt.net/cim

38

articlea

⊲ Reiter and a mechanical engineering company have co-developed an

assembly robot that can detect and precisely place contact pins despite

their minute dimensions. ⊲

Adapter carrier wafers for exceptional fl exibility

The semiconductor and MEMS industry is producing wafers with an increasing variety of diameters. However, the processing equipment required for di� erent wafer diameters or substrate dimensions is not a� ordable for all companies. Adapter carrier wafers feature pockets to hold wafers with smaller diameters or substrates of smaller dimensions and carry them through the process (fi gure 5). This allows

for the handling and processing of a variety of di� erent wafer and substrate sizes on existing equipment.

Adapter carrier wafers are either surface processed glass or silicon wafers with patterned pocket(s) or silicon wafers permanently bonded to borosilicate glass rings that have been patterned according to the dimensions of the substrate. The so-formed pockets on the wafer with required outer diameter enable processing of smaller wafers and

Adapter carrier wafers are either surface processed glass or silicon wafers with patterned pocket(s) or silicon wafers permanently bonded to borosilicate glass rings that have been patterned according to the dimensions of the substrate.

⊲ Figure 5:Adapter debonding. ⊲

Adapter carrier wafer.

Silicon wafer on an imperforated glass carrier wafer.

commercial micro manufacturing international Vol 11 No. 6 39

article a

substrates, for example, 150 mm wafers on 200 mm equipment. Even multiple small substrates can be handled, for example, four 76 mm wafers on a 200 mm carrier wafer.

Options are:

• glass carrier wafers with patterned pockets;

• silicon carrier wafers with patterned pockets; and

• silicon carrier wafers permanently bonded to glass rings.

Due to the materials used, these carrier wafers can be used in operating temperatures up to 500˚C. In addition, holes or grooves can be added to enable the use of adapter carrier wafers with vacuum chucking. Unique marking by quick response (QR) codes can be applied for easy tracking.

Conclusion

Carrier wafers made of glass, quartz or silicon are fundamental tools for 3D wafer-level packaging of MEMS and sensors. Plan Optik manufactures high-end glass, quartz and silicon carrier wafers for many MEMS- and semiconductor-related processes. They can provide, as outlined above, chemical and high-temperature resistance, exceptionally low tolerances and thermal expansion adjusted to silicon or other substrate materials. Furthermore, non-sticking or sticking surface properties can be incorporated, and excellent surface quality is achievable through double-sided polishing. ●

Plan Optik www.planoptik.com

http://www.planoptik.comhttp://www.sensofar.com