Commands v1[1].6.5

8/8/2019 Commands v1[1].6.5

http://slidepdf.com/reader/full/commands-v1165 1/24

:: MDS-SERIES (CISCO) COMMANDS ::

MDS-SERIES Switch Commands

ip address 191.168.123.234 255.255.255.0

View = show running-config

show environment shows status of all in

show flogi database shows database listshow fcns database shows database list

show vsan membership shows list of VSAN m

show interface brief lists the interfaces an

MDS-SERIES Zoning Commands

config terminal Enters configuration te

zone name TestZone1 vsan 4 creates a zone

member pwwn 10:01:10:01:10:ab:cd:ef adds node to the zon

no member pwwn <colon separated wwn> deletes member from

zoneset name Zoneset1 vsan 4 creates a zoneset

member <zone name> adds zone to the Zone

no zone name <zone name> vsan <vsan Id> Deletes a zonezoneset activate name Zoneset1 vsan 4

zone copy active-zoneset full-Zoneset1 vsan 4

copy running-config start-up config copy from source to s

vsan database go into vsan configura

vsan 4 interface fc3/21 move port 21 on modu

show zoneset shows all zonesets th

show zone vsan <#> shows all zones activ

show zoneset active displays the active zo

show vsan shows the vsans on t

show zoneset active vsan <vsan Id> Shows active zoneset

:: B-SERIES (BROCADE) COMMANDS ::

B-SERIES Switch Commands

switchDisable offline

ipAddrSet set the IP address of a

switchShow display switch info

supportShow full detailed switch inf

portShow # display port info

nsShow Name server content

nsAllShow NS for full fabric

fabricShow fabric information

ad --create create a new Admin D

ad -apply enforce the new Admi

B-SERIES Zoning Commands

aliCreate "Alias", "20:00:00:e0:69:40:07:08"

zoneCreate "Zone1", "20:00:00:e0:69:40:07:08; 50:06:04:82:b8:90:c1:8d"

cfgCreate "Test_cfg", "Zone1; Zone2"

cfgSave saves zoning informa

cfgEnable "Test_cfg"

zoneShow or cfgShow shows defined and ef

8/8/2019 Commands v1[1].6.5


zoneAdd adds a member to a

zoneRemove removes a member f

zoneDelete deletes a zone

cfgAdd adds a zone to a zon

cfgRemove removes a zone from

cfgDelete deletes a zone from

cfgClear clears all zoning infor

:: M-SERIES (McDATA) COMMANDS ::

M-SERIES Switch Commands

View= config ip show

Config> ip (new IP and Subne

Show> switch

Show> switch

Show > system

Show> nameserver

Show> loginServer

Show> nameServer Show.Fabric> nodes

Maint > system > setOnlineState

M-SERIES Zoning Commands

Config.Zoning> addWwnMem: <zoneName> <wwn>

Config.Zoning> addZone add a new zone to th

Config.Zoning> activateZoneset activation of changes

Config.Zoning> showactive shows actively conne

Config.Zoning> clearZone clear WWNs in a zon

Config.Zoning> deletezone remove zone from th

Config.Zoning> showPending show pending zones

Config.Zoning> renameZone:<oldzonename><newzonename>Config.Zoning> deleteWwnMem <zonename><wwn>

Config.Zoning> renameZoneSet <zoneSetName>

::Veritas VM HOST COMMANDS ::

http://www.symantec.com/business/support/documentation.jsp?language=english&view=manuals&pid

Veritas VM Device Commands

vxdisk list List all disks under v

vxdiskadd c1t2d3 add or bring a disk u

vxdiskadmin Interactive front end t

Veritas VM Filesystem commands

vxdisk init Initialize Physical Volvxdg init mydg mydg-01=c1t11d0 Create Disk Group

vxassist -g mydg make myvol <size> Create Logical Volum

mkfs -F vxfs /dev/vx/rdsk/mydg/myvol create file system

vxvol -g mydg stopall stop a volume

vxdg deport mydg deport disk group

vxdg import mydg import disk group

vxvol -g mydg startall starting a imported vo

8/8/2019 Commands v1[1].6.5


::VMware ESX HOST COMMANDS ::

http://www.b2v.co.uk/b2vguide2vmware.htm

http://b2v.co.uk/b2vguide2vmware3.htm

VMware ESX Device Commands

esxcfg-rescan <vmkernel adpter> scan for new disks

esxcfg-swiscsi -e enable iSCSI initiator more /proc/scsi/lpfc/X wwn of HBA

esxcfg-vswitch

VMware ESX Filesystem Commands

vmkfstools

:: Windows HOST COMMANDS ::

http://support.microsoft.com/default.aspx/ph/3198?sid=26

Windows 2003 server SP1 Device Commands

SystemInfo Displays detailed con

Shutdown /r /f forced reboot

Netstat Displays active TCP

mstsc /v: 255.255.255.255 /console launches a Remote d

net use \\ComputerName\ShareName\volume Connects a compute

FC compares two files an

ChkDsk check and repair disk

Recover Recover a damaged

fcinfo /details if fcinfo is installed ,thi

Windows 2003 server SP1 LVM Commands

Diskpart rescan Locates new disks th

Diskpart list disk Displays a list of disk

Diskpart select disk Selects the specified

Diskpart detail disk Displays the properti

Diskpart create partition primary align=64 create a properly offse

MountVol Creates, deletes, or li

Diskpart assign Assigns a drive letter

Diskpart extend Extends the volume w

Diskpart import Imports a foreign dis

Format /FS:filesystem Specifies the type of t

FSutil volume dismount:: VI COMMANDS ::

Cursor movements

h left one character

l right one character

j down one

k up one line

w right one word

b back one word

8/8/2019 Commands v1[1].6.5


Deleting, Yanking, and Pasting

d delete

x delete character curs

r replace one character

y yank (copy into tempo

Y yank line cursor is onp paste below cursor lin

Saving and Exiting

u undo last editing com

ZZ save and exit (hold do

:wq! write and quit even if i

:: FTP COMMANDS ::

open <IP address> undo last editing com

close <IP address> save and exit (hold do

bin set to transfer for bina

hash display progress durinmget mutiple get - download

mput multiple pu - upload fil

:: AIX/IBM HOST COMMANDS ::

http://publib.boulder.ibm.com/infocenter/pseries/v5r3/index.jsp?topic

AIX Software Installation

/usr/lpp Software Directory

lslpp -L all List installed softwar

lslpp -f fileset List all files

instfix -i List installed patches

cp *.lpp /usr/sys/inst.images copy lpp software to tsmit installp Install a software pac

rmdev Remove a device

AIX Device Commands

lscfg lists all comfigured co

smit or smitty system management

lscfg -v l <interface> lists all attributes (W

emc_cfgmgr configures symmetrix

mkbcv makes BCV visable t

(1) chdev -l fcsX -a init_link=pt2pt -P "To change INIT Link

(2) chdev -l fscsiX -a fc_err_recov=fast_fail -P "Fabric Event Error R

(3) cfgmgr -v cofigures devices an

AIX NFS Commands

exportfs Lists all exported files

exportfs -a Exports all fs's in /etc/

exportfs -u (filesystem) Un-exports a filesyste

mknfs Configures and starts

rmnfs Stops and un-configur

mknfsexp -d /directory Creates an NFS expor

8/8/2019 Commands v1[1].6.5


mknfsmnt Creates an NFS moun

mount hostname:/filesystem /mount-point Mount an NFS filesyst

nfso -a Display NFS Options

AIX iSCSI Commands

smit iscsi

AIX Filesystem Commands http://the-welters.com/professional/aix/jfs-lvm.html

lsdev -Cc disk Device Listing and st

mkdev configures a disk dev

chdev -l hdisk# -a pv=yes Initialize Physical Vol

lspv -l hdisk# Disk Label

mkvg -y myvg -s 16 hdisk2 groups one or more

mirrorvg Creates mirror volume

extendvg myvg hdisk3 hdisk4 Extend Volume Goup

lsvg -l vgname displays volumes, wit

mklv -y mylv myvg 16 Make logical volume

mklvcopy hd1 2 hdisk1 (2) makes a copy of l

lslv List Logical Volumechfs -a freeze writes all dirty file syst

crfs -v jfs -d mylv -m /myfs

mount mounts a filesystem

varyoffvg myvg Deactivate Volume G

exportvg myvg Export Volume Group

importvg -y myvg -f /dev/hdisk9 Import Volume Group

varyonvg myvg Activate Volume Grou

:: HP/UX HOST COMMANDS ::

http://www.docs.hp.com/en/B2355-90681/index.html

HP/UX Software Installation

sysdef analyzes current run

swlist -l bundle displays version and

swlist -l patch List installed patches

swreg -l depot /full/path/to/your/depot_file Register a depot pack

swinstall Install the Software d

HP/UX Device Commands

insf -e install special device

ioscan -fnC disk scans system hardw

sam System administratio

dd if=/dev/rdsk/c34t15d0 of=/dev/zero count=1 makes HP register winavicli -h <SP IP> register registers host with Cla

lsdev -C disk list device drivers in t

mknod makes a directory, sp

/stand/system system configuration

HP SAN Commands

fcmsutil /dev/fcd0 List HBA wwn

tdutil /dev/td0 List HBA wwn

8/8/2019 Commands v1[1].6.5


HP iSCSI Commands

http://docs.hp.com/en/T1452-90011/T1452-90011.pdf

HP NFS Commands

/etc/exports file controls which file

/exported/directory example.emc.com Exports directory to hoexportfs -a command to read /etc/

mount shadowman.emc.com:/misc/export /misc/local mount an NFS export

HP/UX Filesystem commands

pvcreate /dev/rdsk/c1t0d2 creates a physical vo

pvdisplay display info about ph

ls -l /dev/*/group list the minor number

mkdir /dev/myvg Create directory entry i

mknod /dev/myvg/group c 64 0x010000 Create a file for Volu

vgcreate -s 16 /dev/myvg /dev/dsk/c1t0d0 creates a LVM volum

vgextend /dev/myvg /dev/dsk/c1t0d1 add disk to VG

vgchange -a y myvg Avtivate VGvgscan scan physical volume

vgdisplay displays info about L

lvcreate -l 16 -n mylv /dev/myvg creates LVM logical

lvcreate -m mylv /dev/myvg creates mirrored logi

lvdisplay displays LVM logical

newfs /dev/myvg/rmylv Create file system

mount /dev/myvg/mylv /myfs Mount file system

vgchange -a n myvg Deactivate Volume G

vgexport myvg Export Volume Group

vgimport /dev/myvg /dev/dsk/c1t0d0 Import Volume Group

:: PROCEDURES ::

zone hp server to symm

symmask list hba -v to list your servers pat

symmask -wwn -dir -p add dev (use wwn, dir, p value

symmask -wwn -dir -p set heterogeneous on HP_UX use wwn from the (sy

symmask refresh

ioscan -fnC disk

insf -esymcfg dis

sympd list

8/8/2019 Commands v1[1].6.5


To get HPUX to register with Clariion if using NaviAgent

Install NaviAgent

Edit agent.config file

ioscan -fnC diskinsf -e

/sbin/init.d/agent stop

rm /etc/log/HostIdFile.txt

/sbin/init.d/agent start

dd if=/dev/rdsk/c34t15d0 of=/dev/zero count=1 makes HP register wi

navicli -h <SP IP> register registers host with Cla

# rmsf path ( The paths are showing NO_HW or not sensing).

# ioscan -fnc disk (check)

# insf -e

# symcfg discover

# powermt display ( check for any dead path)

# powermt check (checks and corrects dead path).

# powermt config

# powermt save

:: Linux HOST COMMANDS ::http://www.redhat.com/docs/manuals/enterprise/RHEL-5-manual/en-US/

Linux Software Installation

rpm -hiv

Linux Device Commands

modeinfo lpfc | grep parm Emulex hba paramete

lsmod | grep lpfc look for Emulex HBAs

modprobe -r lpfcdfc unload Emulex driver f

modprobe -r lpfc discover new disk

dmsetp ls list devices managed

/sys/class/scsi_host/host1/issue_lip discover new diskdmesg |grep scsi list scsi devices

/sys/class/scsi_host/host1/scan discover new disk

/usr/sbin/lpfc lun_scan all

Linux FC SAN Commands

hbacmd list list Emulex hba

hbacmd allnodeinfo xx:xx:xx:xx:xx:xx:xx:xx detail hba wwn info &

more /sys/class/scsi_host/hostX/port_name wwn on RHEL4

8/8/2019 Commands v1[1].6.5


more /sys/class/fc_host/hostX/port_name wwn on RHEL5

Linux iSCSI Commands

yum install iscsi-initiator-utils install iSCSI soft initiat

rpm -q srvadmin-deng iscsi-initiator-utils install iSCSI soft initiat

rpm -ql iscsi-initiator-utils confiure iSCSI soft initi

iscsi-iname discover iqniscsi-ls list adapters

iscsiadm -m discovery -t -p 192.168.1.100 discover iSCSI target

iscsiadm --mode node --targetname iqn

Linux NFS Commands

/etc/exports file controls which file

/exported/directory example.emc.com Exports directory to ho

exportfs -a command to read /etc/

mount shadowman.example.com:/misc/export /misc/local mount an NFS export

redhat-config-nfs RedHat NFS tool

Linux Filesystem commands http://linux.about.com/od/commands/l/blcmdl_8m.htmpvcreate /dev/emcpowerX initializes PhysicalVol

vgcreate VG_Name /dev/emcpowerX creates a new volume

lvcreate --size 2000m --name LV_Name /dev/VG_Name creates 2000MB logic

mkfs -t ext2 /dev/VG_Name/LV_Name Make a file system on

mount -t ext2 /dev/VG_Name/LV_Name /mnt/FS_MountPoint mount File system

df -a display filesystems

Fdisk /dev/sda partition table manipul

pvdisplay allows you to see the

pvscan scans all supported L

vgdisplay display attributes of vo

vgextend allows you to add one

vgscan scan physical volumevgexport make volume groups

vgimport make volume groups

lvdisplay display attributes of a l

lvextend Extend logigal volume

fsck Command used to che

:: SUN/SOLARIS HOST COMMANDS ::

http://developers.sun.com/openstorage/articles/opensolaris_storage_server.html

SOLARIS Software Installation

ptree -a Shows all running proshowrev -p Displays currently inst

prtconf prints system configu

pkginfo lists installed softwar

pkgadd install software pack

pkgrm removes installed sof

Solaris Device Commands

cfgadm -a list all

8/8/2019 Commands v1[1].6.5


cfgadm -c configure c4 configure StorEdge L

devfsadm -vC searches for devices

update_drv -f sd -d -I searches for devices

drvconfig generates special de

reboot -- -r reboots system to dis

/etc/system system files

/kernel/drv/sd.conf lists of available targ/kernel/drc/lpfc.conf used for persistent bi

/var/adm/messages system messages

Solaris iSCSI Commands

iscsiadm add static-config iqn.1999-08.com.array:sn.01234567,192.168.1.3:32 map target

iscsiadm add discovery-address 192.168.1.13:3260

iscsiadm modify discovery --isns enable

iscsiadm list target -vS Target: iqn.1986-03.com

devfsadm -Cv -i iscsi

Solaris FC SAN Commands

fcinfo hba-port Lists information andfcinfo remote-port -p 10000000c937694f -ls Lists the remote-port i

fcadm create-fcoe-port -t nxge0 Creates a FCoE target

Solaris NFS Commands

share -F nfs -d "Cartman dir" / share2

mount -F nfs cartman:/share2 /cartman

share -F nfs -o ro=sun.ucs.indiana.edu,rw=teak.uwsg.indiana.edu /reports export (share) /report

/etc/dfs/dfstab file to edit to make a s

shareall -F nfs command to excute t

SOLARIS Filesystem Commands

*** Format and lable all devices before using zpool ***zpool create spoon c3t6d9 create & mounts stora

zpool create spoon mirror emcpower3c emcpower4c create a RAID1 storag

zpool destroy -f spoon destroy a zpool

zfs create spoon/fs creates ZFS file syste

zpool list list pools

format Disk partitioning and

sysdef Device Listing

prtvtoc Disk Label

metadevadm Checks device ID con

metainit Configures volumes.

metastat Displays the status of

metaset Administers disk sets.newfs -v makes a UFS filesyst

:: SOLUTIONS ENABLER COMMANDS ::

Commands to see devices

syminq list all devides seen b

syminq -cids list Clariion devices

8/8/2019 Commands v1[1].6.5


syminq hba -fibre list HBA

syminq -pdevfile List the location of dev

sympd list lists the Symmetrix d

sympd list -vcm lists all the physical d

symdev list pd lists the Symmetrix de

symdisk

Symdev Commands

symdev list list all devices on sym

symdev -sa -p list list devices maped to

symdev list -noport list devices not mapp

symdev list -clariion

symdev show 0123 -v vebose listing of one

symdev list -RANGE 0001:0123 -v vebose listing of a rag

Symcfg Commands

symcfg discover discover the storage

symcfg list list local and remote s

symcfg list -clariion list clariionssymcfg list -v lists whether the Sym

symcfg list -FA all list lists all fibre directors

symcfg list -dir all -address -sid 6196 identify the address i

symcfg list -dir all -address -available sid 6196 returns the

symcfg list -lockn all list of visible Symm e

symcfg -sid 098712341357 -lockn 15 release release a lock on a S

Symconfigure Commands

symconfigure -sid <sid> -f <filename> preview checks file to make s

symconfigure -sid <sid> -f <filename> commit makes the changes f

symconfigure -sid <sid> -f <filename> prepare

Symmaskdb Commands

symmaskdb list devs lists all devices acces

symmaskdb remove removes the meta m

symmaskdb restore restores a database f

symmaskdb backup backs up a database

symmaskdb init deletes and creates

symmaskdb list assignment lists deives already as

symmaskdb list no_assignment lists deives not yet ass

Symmask Commands

symmask add devs adds a device to the l

symmask remove devs removes a device frosymmask delete deletes all access rig

symmask replace allows one HBA to re

symmask refresh refresh vcmdb to all

symmask login lists for each Fibre di

symmask list HBA's lists the WWN of the

symmask -sid 381 -wwn 50060B000024F9F6 -dir 16C -p 1 set heterogeneous on HP_UX

symmask -sid SymmID set lunoffset on offset base \ -awwn awwn -dir # -p # offset high lun numbe

symmask -wwn add devs -lun xxx allows HVE to be see

8/8/2019 Commands v1[1].6.5


symmask -wwn add devs -dynamic_lun allows HVE to be see

Other SYMCLI Commands

symsan list ports and LUN W

symdg creates/deletes/renam

symld addes & removes desymbcv associates/disassocia

symmir performs (split/establi

symclone performs (split/establi

symsnap performs (restore/acti

symrdf performs (split/establi

symcg Performs operations

symrslv Displays logical-to-ph

symstat Displays statistics inf

symioctl sends I/O control co

:: NAVICLI COMMANDS ::

navicli -h <SP IP> getsp verify connectivity

navicli -h <SP IP> register registers host with Cla

navicli -h <SP IP> storagegroup list all info about existi

navicli -h <SP IP> getrg -lunlist list all existing raid gro

navicli -h <SP IP> getdisk shows numbers of dis

navicli -h <SP IP> getrg <rg id> shows the number of

navicli -h <SP IP> get lun <lun id> lists all the disks

navicli -h <SP IP> storagegroup -list displays storage grou

navicli -h <SP IP> getcache shows the cache

navicli -h <SP IP> storagegroup -create -gname <name> creates a new storag

navicli -h <SP IP> storagegroup -addhlu -gname <name> -hlu <#> -alu <#> assigns LUNs to stor

navicli -h <SP IP> storagegroup -connecthost -host <hname> -gname <gname assigns host to stora

:: POWERPATH COMMANDS ::

powermt manage powerpath e

powercf configure powerpath

powermt display dev=all display PowerPath co

powermt checkpowermt config

emcpreg manage powerpath li

emcpupgrade convert powerpath c

:: INQ ::

ftp://ftp.lss.emc.com/pub/symm3000/inquiry/

8/8/2019 Commands v1[1].6.5


Inq -h list options and synta

Inq -hba list hba wwn

Inq -btl display Bus Target an

Inq -show_vol display Symmetrix Vol

Inq -winvol show Windows filesys

Inq -clariion display CLARiiON de

inq -dev \\.\physicaldrive1 -page0 Raw unformatted dat

8/8/2019 Commands v1[1].6.5


stalled hardware components

f all FLOGI eventsf all N-ports logged in

embers

d status

rminal

above

one

Set above

tartup configuration

tion mode

le 3 to vsan 4

at are active

e in vsan

neset

he switch

Brocade switch

o

s

omain.

Domain configuration.

tion across reboots

fective zones and configurations

8/8/2019 Commands v1[1].6.5


one

om a zone

e configuration

a zone configuration

zone configuration

mation/ must disable the effective configuration

t mask)

e working area

cted running zoneset

e

running config

=15273

lume manager control and give there status.

der volume manager control

o the vxdisk program

me

e

lume

8/8/2019 Commands v1[1].6.5


figuration information about a computer and its operating system

connections, ports on which the computer is listening

sktop Connection

to a computer shared resource

d displays the differences

problems

file from a defective disk.

is will list the HBA's wwns

at may have been added to the computer

s and information about them,

isk and shifts the focus to it.

s of the selected disk and the volumes on that disk.

t partition

ists a volume mount point.

or mount point to the volume with focus.

ith focus into next contiguous unallocated space

group into the local computer's disk group

he file system (FAT, FAT32, or NTFS).

8/8/2019 Commands v1[1].6.5


r is on

rary buffer)

e (deleted or copied text)

and

wn shift and press "z" twice)

t is read-only

and

wn shift and press "z" twice)

y and text files

g getfiles in to current directory

s from current directory

e install directoryage

mponents

utility

N's) for a device

devices

o AIX to avoid locking during boot

flags parameter"

COVERY Policy"

optionally installs device software

stems

xports file

NFS services

es NFS services

t directory

8/8/2019 Commands v1[1].6.5


8/8/2019 Commands v1[1].6.5


ystems are exported to remote hosts and specify options

st example.emc.com (found in /etc/exports)export and export filesystem

rom shadowman.emc.com to the dir /misc/local

lume within a LVM volume group

sical volumes within an LVM volume group

f each vg in 6th field (all not listed are available)

in /dev for Volume Group

e Group

e group

s for LVM volume groups

M volume groups

olumes

al volumes

volumes

oup

hs to the symm

s from above command) run command for each hba to FA zone

mask list hba -v )

8/8/2019 Commands v1[1].6.5


ith a Clariion thru LUNZ device

riion and tests agent install

rs

ollow by "modprobe -r lpfc"

y MPIO

evice list

8/8/2019 Commands v1[1].6.5


or

or

iator

ystems are exported to remote hosts and specify options

st example.emc.com (found in /etc/exports)

export and export filesystem

ume for later use by the Logical Volume Manager

group

l volume

a logical volume

lation

attributes of one or more physical volumes

M block devices in the system for physical volumes

lume groups

or more initialized physical volumes

s for LVM volume groupsnknown to the system

nown to the system

ogical volume

ck and repair a Linux filesystem

cesses in a tree formatalled Solaris patches

rations

packages

ges

tware packages

8/8/2019 Commands v1[1].6.5


adville driver.(Search for new devices)

nd also cleans up old

ice files

cover configuration changes, and rebuild special files

t ids and lunsnding on Emulex (qla22xx.conf for Qlogic)

WNsnformation

port

s

hare permanent

at will read /etc/dfs/dfstab and share to the network

ge pool named spoon and mounts it at /spoon (no slice #)

e pool mounted at /spoon

spoon/fs, automatically mounted at /spoon/fs.

aintenance program

figuration.

volumes or hot spare pools.

em on disk drive or partition within a diskdrive

host OS

8/8/2019 Commands v1[1].6.5


ices

evices that the host OS can see

evice name in the device masking database

vices that the host OS can see

m

that one FA

ed to any FE ports

device

e of devices

environment

ymmetrixes

metrix director has device masking turned on

in a Symmetrix system

formation for devices

next available LUN address

xclusive locks

ymmetrix array.

ure it is ok to exe

rom file

sible to an HBA on a specified Symmetrix system

mber devices

rom a specified file

to a specified file

new VCMDB

signed

igned

list of devices that a WWN can access in the database

m the list of devices that a WWN can access in the databasehts for a WWN in the database

place another

A ports

rector which hosts and HBA's are logged in to a Symmetrix system

Fibre HBAs on this host

rs

n by an HBA using different LUN # than in BIN file

8/8/2019 Commands v1[1].6.5


n by an HBA using different LUN 0+

Ns seen from a specific Symmetrix director and port

es device groups

ices to a deivce groupte BCV with device groups

sh/restore) BCV mirror commands against device groups

sh/restore/activate/terminate/recreate)

ate/terminate/recreate)

sh/restore/failover/update/failback/suspend/resume) against RDF device groups

on a Symmetrix RDF composite group

ysical mapping information about a logical object that is stored on a disk.

ormation about a Symmetrix, any or all directors, a device group, a disk, or a device.

mands to application

riion and tests agent install

ing groups

ups and LUNS

ks in storage array

raid groups

ps

e group

age group

e group

nvironment

devices

trolled devices

cense registration

nfiguration files

8/8/2019 Commands v1[1].6.5


d Lun

lume Number.

tems

ice information

on a single device

Documents

Commands v1[1].6.5