Commands for O M (1)

DOCUMENTTYPE 1 (13)

TypeUnitOrDepartmentHereTypeYourNameHere TypeDateHere

MSS/MGW Commands

To check alarms

ZAHO::CLS=AL1; --To see alarm class 1.-------------MSS ZAHO::CLS=AL2;--- To see alarm class 2. ZAHO::CLS=AL3;-- To see alarm class 3. ZAH0::NR=2018;-- To see alarms by number.

ZAHO; -------- To see alarm history.

ZABO; ---- To see blocked alarms

ZAAP::CLS=AL1; -------To see alarm class 1 ---------------MGW ZAAP::CLS=AL2; ------- To see alarm class 2ZAAP::CLS=AL3; ------- To see alarm class 3ZAAP::NR=2018; ---- To see alarms by number

ZAHP; --- To see alarm history

------------------------------------------------------------------------------------------------------------------------------------

PCM Status for MSS/MGW

ZYEF:ET,257; --- To see PCM status

ZYEI:ET,257; --- To see frame alignment mode of PCM. For Inter MSC and POI it should be DBLF and for ATER it should be CRC4.

ZUSI:ET,257; ----- To check the working status of ET it should be WO-EX always-------------------------------------------------------------------------------------------------------------------------------------

To check the command calendar

ZICL; --- All the commnds should be in unblock condition.

ZICL::COM; ---- All the commnds should be in unblock condition.

If you find commnds are blocked then you can unblock by using the following command :-

ZICB:XX:UNBLOCK; --- Where XX means Task Identifier.-------------------------------------------------------------------------------------------------------------------------------------

To See VMGW state

MSS

ZJGI; ----- All the VMGWs should be in registered condition.

Also check the state of SIGU by fillowing command:-

ZUSI:SIGU; ---- All SIGUs should be in WO-EX condition except one in SP-EX.

DOCUMENTTYPE 2 (13)


MGW

ZJVI; --- All the VMGWs should be in registered condition

-----------------------------------------------------------------------------------------------------------------------------------

Fallback

Fallback in (HDD) in MSS/MGW

ZWQO:CR; ----- To see created software package.

ZWQO:RUN; -----To see running package.

One package should be in BU condition .

ZWQD:NAME=<PACKAGE NAME>:DIRE,::; ---------To delete old software package

ZWKS:MODE=FULL,NAME=FB160309,DIRE=FB160309::; --- To start fallback in HDD

ZWKI::; ---------- To see fallback progress

Fallback in MOD In MSS/MGW

ZIPS:"OMU",WDU-S,/FB160309,,:"OMU",FDU-0,,,:NAME=FB160309,DIR=INC,ISD=Y,:DCM=NEW,:;To start fallback in MOD form HDD

ZIPI:ID=4002D740; -- To see the fallback progress -----------------------------------------------------------------------------------------------------------------------------------------

Unit Checking

ZUSI; ---- To see unit state in MSS and MGW

ZUSI:COMP; --------- To see all computer units in MSS

ZUSI:<UNIT NAME>; ----- To see specific unit state in MSS and MGW

Replacing the faulty unit

ZUSI: Comp;If Unit showing SE-NH (SIGU-5)

ZUDU:SIGU,5:::; ---- To start the daigonesis of the sigu

ZUDQ; ---- To see current diagonesis test

ZUDH:SIGU,5:::; --- To see the diagonesis history

If DGN result of unit not showing OK

DOCUMENTTYPE 3 (13)


Check the Physical location of unit:

ZWTI :P:SIGU,6:;

Replace the working UNIT:

ZUSC:SIGU,6;TEZUSC:SIGU,6:SE(SE-OU)ZUSC:SIGU,6:SE(SE-NH)Now replace the Unit again do the 3(ZUDU,ZUDQ,ZUDH) Command. If ok.ZUSC:SIGU,5:SP/WO

To see subscribers in VLR in MSS

ZMVI; ---- To see total subecriber count in VLRs

ZMVF::PLMN=ALL; --- To see subecribers PLMN wise

ZMVF::LAC=<LAC NUMBER>; --- To see subecriber LAC wise

ZMVO:MSISDN=919176098909; --------- To see a subecriber in VLR

ZMVS:IMSI=405800170001139:BSERV=T11; ----To see SUPPLEMENTARY services of the subecriber in the VLR.

ZMVR:IMSI=405800170001139:; ----- To see OPERATOR DETERMINED BARRING DATA in VLR.

ZMVG:IMSI=405800170001139:BSERV=T11; --- To see CAMEL data in VLR.

ZMVD:IMSI=405800170001139::; --- To delete a subscriber from VLR.-------------------------------------------------------------------------------------------------------------------------------------

Signalling Route in MSS/MGW

ZNRI:NA1,D’1234; --- To see signaling route set date where 1234 is the SPC in NA1 where D means value in Decimal

ZNRI:NA0,D’1234; ---- To see signaling route set date where 1234 is the SPC in NA0 where D means value in Decimal

All the routes should be in AV-EX state.

ZNVA:NA0,D’1234; ----- To Allow activation of Route Set

ZNVD:NA0,D’1234; ----- To Deny activation of Route Set

ZNVC:NA0,D’1234::INA; ---------- To inactive Route

ZNVC:NA0,D’1234::INA; ---------- To activate route

DOCUMENTTYPE 4 (13)


----------------------------------------------------------------------------------------------------------------------------------

Link Status in MSS/MGW

ZNEL; --- To see all signaling links

ZNEL:: STATE=UA; --- To see unavailable signaling links

ZOLT; ---- To see link load

ZNCC:LINK NO:PCM-TSL,BIT RATE,NO OF TSL,1:UNIT,INDEX:0:; --- To create a signaling link For example if we give the below mention command link number 1 will be created with bitrate 64 Kbps and PCM no-124 and TSL-16 in CCSU unit 2.

ZNCC: 1:124-16, 64, 1, 1: CCSU, 2:0:;

ZNEL: 1; --- To see signaling link

ZNSC:NA1,D'1234,TEST:1,0:; ---- To create link SET

ZNSI:NA1,D'1234:; --- To see link set data

ZNSA:NA1,D'1234,TEST:2,1:; --- To add link to a link set -------------------------------------------------------------------------------------------------------------------------------------------

Clock SYNCHRONIZATION

ZDRI; ----------- To see external clock synchronization STATE should be connected in MSS

ZUSI:CLS; --- To see internal clock one should bw WO-EX and another should be in SP-EX in MSS

ZUSI:TBU; -- To see internal clock one should bw WO-EX and another should be in SP-EX in MGW

ZDYI; -- To see external clock synchronization STATE should be connected in MGW

ZDCD; --- To see the real time of MSS/MGW----------------------------------------------------------------------------------------------------------------------------------------

I/O Device Interogation

ZISI:,<UNIT>:<I/O DEVICE>,; ----- To see i/o devices state(ZISI:,OMU:WDU,;) in MSS

ZIHI:,<UNIT>:<I/O DEVICE>,; ----- To see i/o devices state(ZIHI:,OMU:WDU,;) in MGW

ZIFI:CHU,0:GSMCHA:; -------------- To see status of the storage data

ZUSI:CHU; ---- To see CHU unit state in MSS

ZIFO:CHU,0:GSMCHA:,OPEN,; ---- To see open file in CHU in MSS

ZIFO:CHU,0:GSMCHA:,FULL; --- To see full file in CHU in MSS

DOCUMENTTYPE 5 (13)


ZIFO:CHU,0:GSMCHA::; ------ To see all file status in CHU in MSS-------------------------------------------------------------------------------------------------------------------------------------------

To see LICENCE and FEATURE in MSS/MGW

ZW7I:LIC,FULL; ---- To see licence capacity

ZW7I: FEA, FULL:FSTATE=ON; ---- To see features in on state-------------------------------------------------------------------------------------------------------------------------------------------

SCTP Configuration Command in MSS/MGW

ZOYI; -- To see SCTP Configuration date

ZOYI:NBR=0:A:; ---- To see SCTP Configuration with all details

-------------------------------------------------------------------------------------------------------------------------------------------GT Analysis and Result Record in MSS

ZNBI::TT=0,NP=1,NAI=4,:9197169; ---- To see GT analysis for SMS (NP=1)

ZNBI::TT=0,NP=7,NAI=4,:9197169; ----- To see GT analysis for Location Update(NP=7)From the output we will get a RESULT Record for example as below RES is 6.

RESULT ANALYSISSS7 GTI TT NP NAI DIGITS RECORD TYPE---- --- --- --- --- ------------------------ ------ --------ITU 4 0 1 4 9197169 6 BASIC

ZNAI:RES=6; ---- To see the SPC for Result Record

To create Result Record we have to create Signalling Route with MML Command as below:-ZNRC:NA1,D'1234,TEST,0,A,N:NA1,D'1234,TEST,7::::;

ZNRI: NA1, D’1234:; --- To see route set data

ZNVA:NA1,D'1234:NA1,D'1234:;

ZNVC:NA1,D'1234:NA1,D'1234:ACT;

Then we have to define SCCP with following command:-

ZNFD:NA1,D'1234,0:6,MAPH,0,:7,MAPV,0,:8,MAPM,0,:92,CAP,0,::;

ZNHI: NA1, D’1234; --- To see SCCP data

ZNHI: NA1, D’1234; --- To see SCCP data

DOCUMENTTYPE 6 (13)


ZNGC:NA1,D'1234:ACT;

ZNHC:NA1,D'1234:6:ACT;




Then use following command to create Result Record

ZNAC:NET=NA0,DPC=D'1234,RI=GT,:::; --- To create Result Record

ZNAI:RES=<RESULT RECORD NUMBER>; ---- To see the output

For example

ZNAI:RES=6;

INQUIRING GLOBAL TITLE TRANSLATION RESULT

RESULT LS SP ENTITY LSRECORD STA IND NET SP CODE H/D NAME RI STATE PR WGHT------ --- --- --- ------------------ ----- --- ------ -- ---- 00006 ACT NO NA1 13C4/05060 HLR01 SSN AV-EX - -

For example RES 6 is routed to SPC- 5060(HLR01).

Then we will check with the following command –

ZNRI:NA1,D’5060;

INTERROGATING SIGNALLING POINT DATA

NET SP CODE H/D NAME RS STATE PAR SET--- ------------------ ----- -------- -------NA1 13C4/05060 HLR01 AV 6 LOAD SHARING BETWEEN SIGNALLING ROUTES ALLOWED

ROUTES: SP CODE H/D NAME STATE PRIO ------------------ ----- ------ ---- 13C4/05060 HLR01 AV-EX 7

CGR Commands

ZRCI; --- To see all the CGRs in MSS/MGW

DOCUMENTTYPE 7 (13)


ZCEL:CGR=404; --- To see calls in a CGR in MSS

ZCII:CGR=555; --- To see calls in a CGR in MGW

ZRCI:SEA=3:CGR=404:PRINT=2; ---- To see Circuit Group parameters

ZRCI:SEA=3:CGR=404:PRINT=5; --- To see all CGR parameters

ZRCI:SEA=3:CGR=404:PRINT=4; --- To see all circuits in CGR

If you want to know a PCM is connected to which CGR then give the below mentioned command:-

ZRCI:SEA=4:CRCT=264-1&&-31; -- Where 264 is the PCM number

To change the state of the circuits in a CGR first give the below mentioned command

ZRCI:SEA=3:CGR=404:PRINT=4;

Kindly note down the PCM numbers and then the below command

ZRCI:SEA=3:CGR=404:PRINT=2;

MAIN LEVEL COMMAND <___>< RCI:SEA=3:CGR=404:PRINT=2;

LOADING PROGRAM VERSION 12.52-0

CIRCUIT GROUP(S)

CGR : 404 NCGR : BSCVIK1E

TYPE : ECCS STATE : WO-EX HUNTED : YES FORMAT : TERMID HM1 : LF HM2 : LF NBCRCT : 1392 TREE : - DIR : OUT LSI : AIF02 INR : - NCCP : - METHOD : - NET : NA1 SPC(H/D) : 1C8B/07307 ASI : - UPART : BSSAP MGW : MSS01MGW0103

FQDN : -

AUTOMATIC CONGESTION CONTROL

REJ11 : - REJ12 : - REJ21 : - REJ22 : - ACT11 : NO ACTION ACT12 : NO ACTION ACT21 : NO ACTION ACT22 : NO ACTION

SELECTIVE CIRCUIT RESERVATION

TRES1 : - TRES2 : - DR1A : - DR2A : - ART1A : - ART2A : - ACTA : NO ACTION DR1B : - DR2B : - ART1B : - ART2B : - ACTB : NO ACTION DR1C : - DR2C : - ART1C : - ART2C : - ACTC : NO ACTION

DOCUMENTTYPE 8 (13)


COMMAND EXECUTED

Then copy the VMGW name (MSS01MGW0103) and then give the below command in MSS only

ZCEC:MGW=MSS01MGW0103,TERMID=10274-1&&-31,:BA; --- To bar the circuits where 10274 is the PCM number

ZCEC:MGW=MSS01MGW0103,TERMID=10274-1&&-31,:NU; --- To not use the circuits in MSS

ZCIM:CRCT=1234-1&&-31:WO; -- To change the state of the circuit in MGW

ZRCC:TYPE=ECCS,CGR=329,NCGR=BSC34SUR:DIR=OUT,NET=NA1,SPC=D'7034,LSI=AIF02,UPART=5:MGW=ASMGW202:; --- To create CGR 329, with Name- BSC34SUR, SPC-7034, and VMGW- ASMGW202

ZRCC:TYPE=SPE,CGR=329,NCGR= BSC34SUR:USE=VMGW:; -- To create CGR in MGW

ZCRM:CGR=329:WO; ---- To change the STATE of the CGR in MSS

ZCIM:CGR=329:WO; ---- To change the STATE of the CGR in MGW

ZRRC:EXT:ROU=329,OUTR=OMCG0,NCCP=MAS,STP=1,TON=UNK,NCGR=BSC34SUR; --- To create Traffic ROUTE in MSS only

ZRCA:CGR=404:TERMID=10234-1&&-31,:CCSPCM=0::UNIT=BSU,INDEX=8:; --- To add circuits in a CGR in MSS only

ZRCA:CGR=329:CRCT=1234-1&&-31; To add circuits in a CGR in MGW only

-------------------------------------------------------------------------------------------------------------------------------------------

IMSI Analysis for Inroaming in MSS

ZCFC:IMSI= 72431,IMSIINDIC=2,PLMN=PCS_BRAZIL,TOA=GT,:NP=E214,TON=INT,SRD=1,NRD=5,SAD=1,DIA=55031,:; --- To create IMSI analysis

ZCFI:TYPE=IMSI:DIG=72431:ALL; ---- To see the o/p of the analysis

ZMXP:NAME= PCS_BRAZIL; --- To see PLMN parameters and check the Supported CAMEL Phaze

IMSI NUMBER ANALYSES

IMSI IMSI PLMN GT NP TON NI SPCNBR. IND.

72431 2 PCS_BRAZIL 55031 E.214 INT - -

NUMBER MODIFICATION RULES: START POINT OF REMOVED DIGITS : 1 NUMBER OF DIGITS REMOVED : 5 START POINT OF ADDED DIGITS : 1 ADDED DIGITS : 55031

DOCUMENTTYPE 9 (13)


ZCFD:TYPE=IMSI:DIG=72431; ---- To delete imsi analysis

From the IMSI analysis o/p check the GT analysis properly with command ZNBI:::55031;

Tracing command in MSS

ZMWC:MSISDN=919716098909:REF=122,:; - To activate trace of a number in MSS

Then give command ZQNS; - to see in which VTP you have logged in. This command shows the command you fired last.

< ZQNS;

LOADING PROGRAM VERSION 12.4-0

MSCi MSS01_GGN 2009-03-16 14:15:35 PAGE 1

SYSTEM USERNAME USER USER MML SESSION SYSTEM I/O-DEVICE NUMBER

220366 MSS01_GGN SYSTEM 220366 MSS01_GGN OMU-VTP20 RI 01244 SYSOP1 220366 MSS01_GGN OMU-VTP15 QN 01237

COMMAND EXECUTED

From above o/p the logged VTP would be VTP-15 , because in its right side it is showing QN command which you fired last.

Then give the command - ZIIS::GSMME1PR::DEV=VTP-15;

LOGICAL FILE MODIFIED:

SYSTEM = MSS01_GGN UNIT = OMU

PAGE 1LOG LOG SPARE PHYSICAL OBJ SYSTEM UNIT DEVICE/FILE FILE FILE FILE IND NAME NAME LOGICALNBR NAME & CLASS MODE NAME FILE

93 GSMME1PR P /TRACE/ 1 MSS01_GGN OMU WDU-SB GSMME1PR.TXT,0 2 MSS01_GGN OMU VTP-23 (** RING FILE **) 3 MSS01_GGN OMU VTP-15

COMMAND EXECUTED

Please note! In device list WDU-SB should be always connected to OMU. At a time max 4 devices can be connected one is WDU-SB of OMU and three are different VTP or LPT.

If you find that 4 devices are already connected and you want to connect another device then you have to give the followind command:-

DOCUMENTTYPE 10 (13)


ZIIS::GSMME1PR:IND=3:DEV=VTP-15;

In this case IND=3 position VTP would be disconnected and new VTP would be added.You can also give IND=2 or IND=4 according to the situation. Please do not disconnect the WDU-SB from OMU.

We can also take trace using the below mentioned command at the time of call test

ZMCJ:IMSI=<IMSI NUMBER>::TYPE=D;

DIAGNOSTIC in MSS/MGW

To do diagonesis of an unit it should be in test mode. For example if we want to diagonose a ET no 258 then we have to change its working state with to TE with command as below:-

ZUSC:ET,258:BL; ---- To block the ET

ZUSC:ET,258:TE; --- To change in to test mode

ZUDU:ET,258:::; ---- To start the daigonesis of the ET

ZUDQ; ---- To see current diagonesis test

ZUDH:ET,258:::; --- To see the diagonesis history

Switchover of Units in MSS/MGW

If we want to switchover the state of an unit we have to use the procedures as below:-

ZUSI:OMU; --- To see the present state of an unit (OMU)

WORKING STATE OF UNITS UNIT PHYS STATE LOCATION INFO OMU-0 0000 WO-EX - OMU-1 0001 SP-EX -

TOTAL OF 2 UNITS

COMMAND EXECUTEDNow if we want to change the state of OMU to WO-EX from SP-EX then we have to give the following command:-

ZUSC:OMU,0:SP,:; --- To switchover the OMU 1 from SP-EX to Wo-EX.

After the command execution the O/P will be as follows:-

WORKING STATE OF UNITS UNIT PHYS STATE LOCATION INFO



OMU-0 0000 SP-EX - OMU-1 0001 WO-EX -

TOTAL OF 2 UNITS

COMMAND EXECUTED

Directed Call Test in MSS

Trunk to trunk test call

For trunk to trunk call e.g POI and Inter MSC call test we have to take a B party test number first.

Then we have to define test case by following command :-

ZYCN:<TEST CASE NAME>:OUTROUT=Y,DIG=9716098909,CON=NAT,CONT=N,:;

Where DIG= B party number

If a testcase is already active deactivate it using the command ----- ZYCE:4:;

Now activate the newly created testcase with the command

ZYCS: <TEST CASE NAME>,4;

Make the A party number in TP in HLR (from where you initiate the calls) with command

ZMIM:IMSI=<IMSI NUMBER>:CAT=TP;

Now make the desired circuits in TE-ID mode with command

ZCEC:MGW=MSS01MGW0103,TERMID=10274-1&&-31,:TE;

Now do test call and check the circuit with command ZMCJ:IMSI=<IMSI NUMBER>;

Call Testing for MOC (In case of ATER call test)

In this case we can do test calls for ATER where A party has to initiate a call provided A party would be under the same BSC for which call test is being done.


ZYCG:<TEST CASE NAME>:OUTROUT=Y,DIG=9716098909,CON=LOC,CONT=N,:;

Where DIG= B party number






Make the A party number in TP in HLR (from where you initiate the calls) with command





Call Testing for MTC (In case of ATER call test)

In this case we can do test calls for ATER where B party has to initiate a call provided B party would be under the same BSC for which call test is being done.


ZYCM:4:INROUT=Y,CONT=N,:




Make the B party number in TP in HLR (from where you initiate the calls) with command





Creation of Directory and files in MSS/MGW

ZIWL::WSB,NODEF::TEST,FF,,AA:; ---- To create the TEST directory

ZIWX::WS,NODEF:TEST,:%,%,; ----- To see the containts of the TEST directory

ZIWC::WSB,NODEF:TEST,:TEST,TXT,20000000,AA:; --- to create TEXT.TXT under the directory TEST

Measurement Commands in MSS



ZTMI:<NAME OF MEASUREMENT>;

ZTGI:CGR,1; --- To see object list

If we create a new CGR then we have to add the CGR in object lis for measurementThe commands are as follows:-

ZTGC:CGR,1:CGR=400:; ---- CGR 400 would be added in object list 1

General Commands in MSS

ZTUT:CLR; ---- To see clear codes generated in MSS

ZTUL:CLR; ----- To see clear code generated in last hour

ZMCJ:ALL=N; ----- To see number of call records in MSS

Documents

Commands for O M (1)