8/14/2019 Colt 1911 pistol slide blue prints
1/6
D
C
B
A
345678
2345678
DWG NO. SH REV
PART NO.
DISTRIBUTION STATEMENT A.
APPROVED FOR PUBLIC RELEASE;
DISTRIBUTION IS UNLIMITED.
07005F0001UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ON:
CONTRACTOR:
NSWC DAHLGREN DIVISION
G32 MINOR CALIBER GROUP
18106 PHALANX DR SUITE 106
DAHLGREN VA 22448-5123FRACTION XX DECIMALXXX DECIMAL ANGLE
-- -- .010 --DEPT NAME DATE(YY-MM-DD)DRAWN BY
PCTDATE (YY-MM-DD)
MINOR CALIBER GROUP 07/05/02
DEPT LEAD
REVIEWED BY
ENGINEER
DESIGN ACTIVITY APPROVAL
ENVIRONMENTAL
APPROVED
THIRD ANGLE PROJECTION
DEPARTMENT OF THE NA
UNITED STATES MARINE C
ALBANY, GA 31 704
TITLE
SLIDE
S IZ E C A GE CO DE D RA WI NG NO .
D 01365 0700SCALE: 2/1 CALC WT -
07005F0002
PISTOL,
SEMI-
AUTOMATIC,
.45 CAL, M45
NEXT ASSY USED ON
APPLICATION
REV
STATUS
REV SH
- 1
- 2
- 3
- 4
- 5
- 6
REVISION
ZONE REV DESCRIPTION DATE
- Issued for Request For Proposal use 08/3
07005F0001 1 -
DATUM LOCATION
DATUM SHEET ZONE
B 2 D-6
C 5 A-6
D 5 D-6
E 4 C-4
F 2 B-2
G 6 A-5
H 4 B-1
J 6 D-1
CAD MAINTAINED. CHAN
SHALL BE INCORPORATE
THE DESIGN ACTIVIT
MARCORSYSCOM
2200 LESTER STREE
QUANTICO, VA 2213
NOTES:
1. THIS DRAWING ESTABLISHES REQUIREMENTS FOR A SLIDE; PART OF
THE
M45 .45 CALIBER SEMI-AUTOMATIC PISTOL.
2. UNLESS OTHERWISE SPECIFIED:
2.1 REMOVE BURRS AND BREAK SHARP EDGES .005 MAX.
2.2 INSIDE CORNERS R .005 MAX.
2.3 SURFACE ROUGHNESS 125
3. MATERIAL: STEEL, CARBON, GRADE 8650 OR 4140, AUSTENITIC GRAIN
SIZE NO. 5 OR FINER, PER ASTM A108
OR A322. MACROSTRUCTU RAL QUALITY SHALL BE S2, R2, C2 OR BETTER
AS PER ASTM E381.
4. HEAT TREATMENT: HEAT TREAT TO RC 38-42. MICROSTRUCTURE SHALL
BE A MINIMUM OF 90 MARTENSITE.
5. THE SLIDE SHALL SHOW NO EVIDENCE OF CRACKS, SEAMS, OR OTHER
INJURIOUS DEFECTS AS
DETERMINED BY MAGNETIC PARTICLE INSPECTION IN ACCORDANCE WITH
ASTM E1444. USE
AC OR DC TYPE MAGNETIZATI ON, 700-800 AMPERES, WET METHOD OF
PARTICLE APPLICATION,
AND EITHER WET VISIBLE OR WET FLUORESCENT TYPE OF PARTICLE.
6. INTERPRET DRAWING IN ACCORDANCE WITH ASME Y14.100 AND
INTERPRET DIMENSIONING
AND TOLERANCING IN ACCORDANCE WITH ASME Y14.5M-1994.
7. QUALITY ASSURANCE PROVISIONS:
7.1 RESPONSIBILITY FOR INSPECTION: UNLESS OTHERWISE SPECIFIED IN
THE CONTRACT OR PURCHASE
ORDER, THE CONTRACTOR IS RESPONSIBLE FOR THE PERFORMANCE OF THE
INSPECTION REQUIREMENT S.
THE GOVERNMENT RESERVES THE RIGHT TO PERFORM ANY OF THE
INSPECTIONS SET FORTH IN THE DRAWING
WHERE SUCH INSPECTIONS ARE DEEMED NECESSARY TO ASSURE THAT THE
SUPPLIES CONFORM TO THE
PRESCRIBED REQUIREMENTS.
7.2 QUALITY CONFORMANCES: UNLESS OTHERWISE SPECIFIED AND WHEN
APPLICABLE, THE QUALITY CONFORMANCE
TEST USED IN DETERMINING THE ACCEPTABILITY OF PRODUCTS SHALL BE
IN ACCORDANCE WITH THE
CONTRACTORS INSPECTION PLAN. INSPECTION OF EACH LOT OF MATERIAL
SUBMITTED FOR ACCEPTANCE SHALL
BE PERFORMED BY THE CONTRACTOR. CERTIFIED TEST DATA WITH
ACCOMPANYING TEST RESULTS ARE ACCEPTABLE.
8. THIS DRAWING IS TO BE USED FOR REQUEST FOR PROPOSALS
ONLY.
SUGGESTED SOURCE(S) OF SUPPLY
VENDOR VENDOR ITEM NUMBER
TO BE DETERMINED N/A
SOURCE CONTROL DRAWING
8/14/2019 Colt 1911 pistol slide blue prints
4/6
D
C
B
A
345678
2345678
DWG NO. SH REV
T
T
VV
.378 .003
.014 H
.51+.01
-.00X 60 1
.449+.004
-.000.499
1.55+.01
-.00
2X MAX.250
3.109+.000
-.015
.375
(TAN TO .375 DIA)
7
R1.818
2X R.18+.00
-.01 .767+.008
-.000
.006 G E B
.473+.008
-.000
.161+.009
-.000
R.375+.000-.031
S IZ E C A GE CO DE D RA WI NG NO .
D 01365 0700SCALE: 2/1
07005F0001 4 -
DISTRIBUTION STATEMENT A.
APPROVED FOR PUBLIC RELEASE;
DISTRIBUTION IS UNLIMITED.
SECTION E-ESH 2, ZONE D-7
SEE DETAIL RSEE DETAIL USH 5, ZONE C-6
SEE DETAIL AJSH 6, ZONE A-7
BREAK SHARP EDGE R.010+.005
-.000
OR .010+.005
-.000X 45 5
DETAIL RSCALE 4/1
SECTION T-T
SECTION V-VSCALE 3/1
VIEW W-W
SEE DETAIL USH 5, ZONE C-6
W
W
SEE DETAIL AJSH 6, ZONE A-7
B
E
E
E
( )2.178
( ).753
68
