Upload
others
View
1
Download
0
Embed Size (px)
Citation preview
Collated T-nut Installation Machine Model Number: HFM-COLL
Patent Pending
Operation Manual
Version 6.16
Page 1 of 2
ISO 9001 CERTIFIED `
Machine Warranty The warranty for this machine is one year on parts; effective from the date the machine was set up. We will guarantee that the mechanical or pneumatic components will operate properly provided the following caution instructions are followed by all the person(s) involved with this machine. This warranty will be considered null and void if the items listed below are not followed:
1. Do not operate without material in position on anvil pin.
2. To prevent unauthorized use of this equipment, disconnect airlines and electrical power line supply to t-nut machine when not in use.
3. DO NOT operate machine with the operator safety shield installed and set to a height of no more than ½” above your work piece.
4. Test the safety switch at the beginning of every shift. This procedure is outlined in Section 8.3 of your operation manual. Do not operate the machine if the safety is not functioning properly. This will void the warranty.
5. Follow the Mechanical Maintenance Outline, Section 8.0, in your machine manual.
6. Do not use synthetic compressor oil in a reciprocating piston type compressor that feeds compressed air to this machine. This type of oil can leak through the reciprocating piston compressor and will damage rubber parts in the pneumatic components rendering them inoperable. Any damage caused by this oil to the pneumatic components may not be covered under warranty.
7. Quality Stafast t-nuts must be used.
“The Right Connection” ®
505 Lake Shore Blvd Painesville, OH 44077 800-782-3278 Fax 440-357-7137
www.stafast.com
Page 2 of 2
ISO 9001 CERTIFIED `
We encourage you to review and stress these caution points with those involved in any way with this machine. To ensure your warranty, please fill out the information on the bottom of page 2, and email a copy to [email protected]. This will acknowledge and confirm your agreement with the preceding caution points. For machine questions please see the first page of your manual for contact information. Sincerely, STAFAST PRODUCTS, INC. Name: Date: Company: Title: . Email Address: Machine Serial #:
Sales Territory Map
Stafast Products, Inc.
Collated T-Nut Installation Manual v.6.16
TABLE OF CONTENTS
Section Shipment Damage Information 1.0 Machine Description 2.0 Safety 3.0 Machine Specifications 4.0 Installation 5.0 Set-up 6.0 Operating Instructions 7.0 Troubleshooting 8.0 Preventative Maintenance 9.0 Inbody Replacement Program 10.0 Parts Diagrams 11.0 Rivet Tool Data Sheets 12.0 Air Schematics 13.0 Machine Parts List 14.0 Machine Maintenance Schedule
Stafast Products, Inc.
Collated T-Nut Installation Manual v.6.16
SHIPMENT DAMAGE INFORMATION Stafast components are crated with the utmost consideration to minimizing damage in transit. If there is any visible damage to the component crate or machine, the shipment should not be accepted until all damage has been noted on the carrier's acceptance slip or bill of lading. All bills of lading received from a carrier should be noted "PROVISIONAL ACCEPTANCE ONLY" and are subject to electrical and mechanical testing. If a shipment appears to have been damaged when it is received, a claim for loss or damage should be placed immediately and directly with the carrier, as the responsible party. In the event of damage, document exact damage with photographs, if possible and contact Stafast as follows:
Stafast Products, Inc. 505 Lake Shore Blvd Painesville, OH 44077 (440) 357-5546 FAX (440) 357-7137 800-782-3278 Stafast of the Carolinas 2426 W. Hwy. 160 Fort Mill, SC 29708 (803) 548-4488 FAX (803) 548-1542 800-951-1159 Stafast South 1698 Hwy.15 North Pontotoc, MS 38863 (662) 489-6580 FAX (662) 489-6853 800-888-6887
Stafast Products, Inc.
Collated T-Nut Installation Manual v.6.16
Section 1.0 MACHINE DESCRIPTION Stafast Model HFM-COLL Collated T-Nut Installation Machine is designed to automatically feed and drive collated T-Nuts into a pre-drilled hole. Coil packaged Stafast collated t-nuts are coil fed and advanced into the firing position by two pusher cylinders. The collated t-nuts are individually advanced under the insert tool, and by depressing the foot pedal, the collated t-nut is sheared from the coil strip and driven into the positioned work piece. Each machine is tooled per customer specifications. The machine is tooled to feed and drive a collated t-nut at a rate of 60 parts per minute, dependent on operator efficiency and work piece configuration. Section 2.0 SAFETY For operator safety, guards have been installed at hazardous locations. Do not remove these items which are there for your safety. 1. A safety switch is incorporated into the anvil locating pin/rivet tool. The collar
must be depressed with the component for the machine to function. 2. Do not operate without material in position on the anvil tool. 3. Disconnect the air supply line before servicing. 4. To prevent unauthorized use of this equipment, disconnect air lines to t-nut
machine when not in use. 5. Do not operate machine without plastic guard set 1/2" maximum above work
piece. 6. Do not operate machine without safety switch. 7. Use only quality Stafast collated t-nuts in this machine. 8. CAUTION: Do not place hands in the anvil area while air is hooked up to
machine.
Stafast Products, Inc.
Collated T-Nut Installation Manual v.6.16
Section 3.0 MACHINE SPECIFICATIONS Dimensions A. Width 30" B. Height 65" C. Depth 60" at full extension of reel arm Electrical Requirements No electricity required to operate machine. Air Pressure Requirements 90 PSI minimum air pressure (constant clean air) on a 3/4” diameter line. Do not exceed 150 PSI. Feed and Drive Rate 60 t-nuts per minute dependent on operator efficiency and type of work-piece used. Section 4.0 INSTALLATION 4.1 When installing the Model HFM-COLL T-Nut Collated Machine, certain preparation
should be made before use. DO NOT CONNECT THE AIR SUPPLY UNTIL YOU REACH THAT INSTRUCTION IN THE INSTALLATION SECTION.
4.2 Remove the machine and all machine parts and accessories from the shipping
crate. 4.3 Remove the machine from the pallet and carefully position the machine where it will
be used. The area where the machine is mounted must be flat and level. Anchor the machine to the floor. The foot pedal can be moved to suit the operator.
Stafast Products, Inc.
Collated T-Nut Installation Manual v.6.16
DO NOT CONTINUE THE FOLLOWING INSTRUCTIONS WITH THE AIR CONNECTED.
4.4 Adjust the front guard to the proper height for the work. This is done by loosening
the screws holding the guard. The clearance between the guard and work piece should never be more than 1/2”.
WARNING: DO NOT OPERATE WITHOUT THE GUARD!! 4.5 The safety switch sensor is attached to the bottom of the anvil plate inside the anvil
pedestal. The safety switch is operated by depressing the locator/safety switch assembly with the component.
DO NOT REMOVE THIS SAFETY SWITCH. IT IS FOR YOUR SAFETY AND
ALSO PROTECTS THE MACHINE FROM FIRING WITHOUT A WORK PIECE IN PLACE, WHICH WILL DAMAGE YOUR MACHINE.
4.6 Connect the main air supply to the rear of the machine using 3/4” ID hose. A 3/4”
NPT quick connect is recommended for connection being made to the air flow shut off valve. A constant supply of air of at least 90 PSI 20 CFM must be maintained. DO NOT EXCEED 150 PSI.
WARNING: DISCONNECT THE AIR SUPPLY BEFORE SERVICING THE
MACHINE!! Section 5.0 SET UP
CAUTION: PROTECTIVE GLOVES SHOULD BE WORN DURING ALL SET-UP AND OPERATION PROCEDURES
5.1 Pull and slowly lower the reel arm attachment at the rear of the machine. Once the
reel has reached its bottom position turn the reel plate horizontally and pull it outward to lock its position.
5.2 Remove the cotter pin and clear polycarbonate cover. Carefully lift one sheet of
collated t-nuts and place them over the center hub of the reel plate. Place the clear polycarbonate cover over the collated t-nuts and replace the cotter pin.
Stafast Products, Inc.
Collated T-Nut Installation Manual v.6.16
5.3 Push the reel arm towards the machine to unlock its position. Turn the reel plate vertically and slowly lift the arm until vertical and the clip has securely grabbed the frame plate.
5.4 Make sure the pusher cylinders are retracted. If they are not, push them back into
the retracted position. 5.5 Grab the first t-nut of the collated strip and feed it into the escapement opening.
Push it all the way forward until it is in the firing position. You will be able to see this is in position by looking at the escapement from underneath.
Section 6.0 OPERATING INSTRUCTIONS 6.1 Before operating the machine, make sure all the installation and set up procedures
have been completed. 6.2 Connect main air supply to the air flow shut off valve. 6.3 Place the work piece over the anvil tool and press down to depress the safety
switch. Keep your hands outside of the machine. Depress the foot pedal. A collated T-Nut will be sheared and inserted into the work piece. The insertion tool will remain in the down position as long as the foot pedal is depressed.
6.4 The force with which the T-Nut is inserted is controlled by the regulator. DO NOT EXCEED 150 PSI UNDER ANY CIRCUMSTANCES!! 6.5 Each time the tool retracts another T-Nut will feed into position for insertion.
Stafast Products, Inc.
Collated T-Nut Installation Manual v.6.16
Section 7.0 Troubleshooting
Problem Potential Cause(s) Remedy Drive cylinder does not fire
Safety switch not engaged or not functioning
Check air lines for kinks in tubing and hoses
Foot pedal not engaged or functioning
Make sure safety switch is performing properly
Switch arm has slipped off the shield
Move switch arm back on the shield
Switch needs to be adjusted because it is no longer being tripped when shield moves up and down.
Adjust by loosening the nut that is holding the arm to the switch, then move the arm to where it needs to be and re-tighten.
Switch has come loose from machine
Tighten switch
Machine is leaking air
Tubing has split or connection with fitting is loose
Locate leak and disconnect air supply to machine
T-nut not seating flush in component
Air pressure setting too low
Increase air pressure until T-nut seats flush with component surface
Pusher has come out of the escapement channels
Escapement channel is bumped or has trash in it or possibly the spring has become weak or is broken
Replace spring to provide tension and keep pusher in escapement channel
T-nuts not feeding properly
Object obstructing T-nuts as they unspool from the coil
Look for slack in the coil that may be catching on something (cardboard, bolt head, etc.)
Debris build-up on pushers or broken pushers
Evaluate pushers and either clean or replace
Stafast Products, Inc.
Collated T-Nut Installation Manual v.6.16
Problem Potential Cause(s) Remedy T-nuts not shearing and driving properly
Broken inbody spring or broken drive pin
Evaluate inbody to determine if spring or drive pin are broken
Dull or broken cutting blade and/or inbody cutting edge
Evaluate blade and inbody to determine if they both have sharp edges
Too much separation between inbody and cutting blade
With air disconnected, pull inbody down. There should be less than 0.020" gap between
If gap is larger loosen cylinder bolts and tap cylinder toward the back of machine to reduce the gap. Retighten bolts after gap is 0.020” or less.
Floating shield not working properly
Pivot pins are loose or out Fit pivot pins back into holes
Washer and snap ring are needed
Replace washer and snap ring
Stafast Products, Inc.
Collated T-Nut Installation Manual v.6.16
Section 8.0 PREVENTATIVE MAINTENANCE WARNING: DISCONNECT THE MAIN AIR SUPPLY BEFORE SERVICING THE
MACHINE!! Preventative Maintenance Program Daily Items:
1) Blow off sawdust and debris from the machine at the end of EVERY shift.
a. Particular attention must be the speed bumps on the left and right side of the escapement.
b. Speed bumps must swivel up and down freely.
2) Depress safety switch with a component and make sure machine fires correctly.
3) Making sure that all hands are clear of the T-nut firing area, step on the pedal and make sure the machine does not fire.
a. If the machine can fire without depressing the safety switch there is an error with the safety system.
b. Machine should not be used until Maintenance fixes the issue.
4) Remove stabands from trap door and blow out inside of escapement
a. Blow off trap door and thoroughly clean out the cutout that catches the T-nut barrel
Bi-Weekly Items:
1) With air to the machine disconnected, remove the speed bumps and pivot pin. Thoroughly cleaned them with a degreaser before reassembling.
2) With air to the machine disconnected, extend & retract both pusher cylinders by hand. Make sure there is no resistance and pusher is attached securely.
Stafast Products, Inc.
Collated T-Nut Installation Manual v.6.16
Section 9.0 Inbody Replacement Program
Blad
e
Check sharpness of cutting blade every 2 weeks. If cutting blade is dull, remove bolts and rotate the blade to utilize an unused edge, and then
re-install bolts. When all cutting blade edges have become dull or visibly damaged, discard blade, and replace with a new blade.
Inbo
dy Check sharpness of inbody every 2 weeks.
If inbody cutting edge becomes dull, remove cylinder, rotate inbody 180 degees, and replace cylinder.
When both edges of inbody become dull replace with spare inbody and return dull inbody to:
Stafast Products (Collated Inbody Sharpening)
Attn: Bill Hornick
505 Lakeshore Blvd.
Painesville, OH 44077
Log:
Date Status
Date Status
Date Status
Date Status
Date Status
Date Status
Date Status
Date Status
Date Status
Date Status
Date Status
Date Status
Date Status
Date Status
Date Status
Date Status
Date Status
Date Status
Date Status
Date Status
Date Status
Date Status
Date Status
Date Status
Stafast Products, Inc.
Collated T-Nut Installation Manual v.6.16
CO
LLA
TED
MA
CH
INE
PAR
TS D
IAG
RA
M
Stafast Products, Inc.
Collated T-Nut Installation Manual v.6.16
MO
DU
LAR
AIR
ASS
EMB
LY
Stafast Products, Inc.
Collated T-Nut Installation Manual v.6.16
PIVO
T SH
IELD
Stafast Products, Inc.
Collated T-Nut Installation Manual v.6.16
REA
R A
RM
ASS
EMB
LY
Stafast Products, Inc.
Collated T-Nut Installation Manual v.6.16
Section 11.0 RIVET TOOL DATA SHEET
Stafast Products, Inc.
Collated T-Nut Installation Manual v.6.16
Section 12.0 AIR SCHEMATICS
AIR
SC
HEM
ATI
C –
CO
LLA
TED
MA
CH
INE
Stafast Products, Inc.
Collated T-Nut Installation Manual v.6.16
Section 13.0 MACHINE PARTS LIST
Item Part Number
Qty Per Machine
Collated Head
Escapement Body COLESCBODY 1 Inbody Guide - Left COLGUIDEL 1 Indody Guide - Right COLGUIDER 1 Speed Bump - Left COLSTOPL 1 Speed Bump - Right COLSTOPR 1 Speed Bump Pivot Pin SBPVTPIN 1 Pushers COLPUSH 2 Pusher Dowel Pin COLPUSHPIN 2 Trap Door COLTRAPDOOR 1 Trap Door Pivot Pin TDPVTPIN 1 Trap Door Stop Bar COLTDSTOP 1 Shearing Blade COLCUTH2 1 Cylinder Mount Plate COLCYLPLT 1 Vertical Post COLCYLPLTV 2 Escapement Mount Plate COLESCPLT 1 Cylinder Cage Top Plate CYLCAGETOP 1 Cylinder Cage Bottom Plate CYLCAGEBOT 1 Cylinder Cage T-nut Guide CYLCAGEGUIDE 1 Cylinder Cage Spacer PUSHCYLSPC 2 Pusher Cylinder Swivel Post PUSHCYLPOST 2 Pusher Cylinder Swivel Post Arm PUSHCYLARM 2
Rear Arm Assembly
Horizontal Arm CLARM 1 Center Hub CLHUB 1 Bearing Mount Disc CFCABSPLH13 1 Table Bearing TBLBEAR 6 Base / Cover Disc CFCABSPL2 2
Inbody Inbody CFINBODYCOLM614 1 Tapered Drive Pin DRPN14T 1 Inbody/Cyl Hex Adapter INBODYADPTR 1
Miscellaneous
Pusher Spring Pin (5/64" X 1/2" Steel Spring Pin) 2 Shoulder Screw (#10-24 Shoulder Screw) 4 Dowel Pin (1/4 X 2-1/2" Steel Dowel Pin) Set Screw (1/4-20 X 1/4 Cone Point Set Screw) 2 E-Style Retaining Clip (3/16 E-Style Clip) 4
Stafast Products, Inc.
Collated T-Nut Installation Manual v.6.16
Item Part Number
Qty Per Machine
Collated Specific
Pneumatic Cylinder (5/8" X 2" Stroke Double Acting Cyl) COLPUSHCYL 2 Extension Spring (3/8" OD X 2-1/2" Music Wire) SPUSHCYL 2 Valve VDRILLCYL2 1 Regulator REG14MAX40 1 5/32 Tube Union F532YUNION 4 1/8 NPT 5/32 Tube Grip F18532TUBE 1 1/4 NPT Vent F14VENT 2 #10-32 5/32 Tube Grip 90 Elbow F1032532TUBE90 4
Core Machine Components
3/4ID Goodyear Hose 34GOODHOSE 3 Drive Cylinder Black CFDRIVEC 1 C-frame CFRAME 1 1/4 NPT 5/32 Tube F14532TUBE90 1 Filter CFF34 1 3/4 Hose Barb Fitting F34HOSEBARB 4 3/4 NPT Brass Muffler F34MUFF 1 3/4 NPT Nipple Fitting F34NIPPLE 2 3/4NPT Silver Muffler F34SMUFF 1 3/4 Street Elbo FTG. F34STELBOW 2 Foot Pedal Cover CFFPCOVER 1 1/8NPT 5/32 Tube Banjo F18532BANJO 2 C-Frame Lexon Safety Shield CFOSHASHIELD 1 Quick Exhaust QEXH 1 3/4 Filter Regulator CFREG34 1 10&1/4 Insert TL. Spring 4 Inch SINTOOL1014 1 Band For Escapement Jaw STABAND 6 3/4 Lockout Valve V34LOCKOUT 1 Foot Pedal Valve CFFPVALVE 1 Poppet Valve VPOPPET 1 Button Pos. Sensor Valve VCSS 1 Angled Anvil Plate ANPLF 1 Locator Tool ANVSS14NC 1 Anvil Pin ANPIN14 2 Anvil Tool Spring SANTOOL 2 Anvil Tool Plug PLUGE 1 Safety Switch Bracket CFSSBRAC 1 Safety Switch Spring SSAFESW 1 1/8 Muffler F18MUFF 1
Stafast Products, Inc.
Collated T-Nut Installation Manual v.6.16
Item Part Number
Qty Per Machine
Core Machine Components
1/4 NPT 5/32 Tube Grip F14532TUBE 6 3 inch 3/4 NPT Nipple F34NIPPLE3 1 Stainless Cotter Pin CFPINCOTTER 1 Pedestal Cap CFPEDCAP 2 1/2 NPT 1/2 Hose Barb F1212HOSEBARB 2 1/2 Goodyear Black 12GOODHOSE 3
Stafast Products, Inc.
Collated T-Nut Installation Manual v.6.16
Section 14.0 MACHINE MAINTENANCE SCHEDULE
Log date and initial when completed.
Date Blow off track, escapement,
and anvil assembly Clean bowl with a quality degreaser
Disassemble, clean anvil & rivet/locating tool
Tighten all bolts