Code: Equipment: Title:

Author : Giorgio Tresoldi Cover for General Document Version:7 Revision:0 Code : IMC 0007XEDG Date : 02/10/2007 pag. 1/2

FOR INTERNAL USE ONLY – FOR INTERNAL USE ONLY

CODE: IMC6011BEDG EQUIPMENT: SRAL XD TITLE: SRAL XD - Single Board 2 DESCRIPTION: Installation Manual LANGUAGE: English VERSION: 2 REVISION: 0 STATUS: Complete DATE: 7/31/2007

Issued by CMO GS NI SE SS. Padana Superiore Km 158 20060 Cassina De Pecchi (MI)

The information in this document is subject to change without notice and describes only the product defined in the introduction of this documentation. This documentation is intended for the use of Nokia Siemens Networks customers only for the purposes of the agreement under which the document is submitted, and no part of it may be used, reproduced, modified or transmitted in any form or means without the prior written permission of Nokia Siemens Networks. The documentation has been prepared to be used by professional and properly trained personnel, and the customer assumes full responsibility when using it. Nokia Siemens Networks welcomes customer comments as part of the process of continuous development and improvement of the documentation.

The information or statements given in this documentation concerning the suitability, capacity, or performance of the mentioned hardware or software products are given “as is” and all liability arising in connection with such hardware or software products shall be defined conclusively and finally in a separate agreement between Nokia Siemens Networks and the customer. However, Nokia Siemens Networks has made all reasonable efforts to ensure that the instructions contained in the document are adequate and free of material errors and omissions. Nokia Siemens Networks will, if deemed necessary by Nokia Siemens Networks, explain issues which may not be covered by the document.

Nokia Siemens Networks will correct errors in this documentation as soon as possible. IN NO EVENT WILL NOKIA SIEMENS NETWORKS BE LIABLE FOR ERRORS IN THIS DOCUMENTATION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES,SUCH AS BUT NOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY OR DATA,THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE INFORMATION IN IT.

This documentation and the product it describes are considered protected by copyrights and other intellectual property rights according to the applicable laws.

The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademark of Nokia Corporation. Siemens is a registered trademark of Siemens AG.

Other product names mentioned in this document may be trademarks of their respective owners, and they are mentioned for identification purposes only.

Copyright © Nokia Siemens Networks 2007. All rights reserved.

AUTHOR: f.to Vergani Anna APPROVED BY: f.to Brambilla Massimo

Author : Giorgio Tresoldi Cover for General Document Version:7 Revision:0 Code : IMC 0007XEDG Date : 02/10/2007 pag. 2/2

FOR INTERNAL USE ONLY – FOR INTERNAL USE ONLY

SAFETY RULES and USE PRECAUTIONS

Mount the systems in areas with restricted access only. Only trained and qualified personnel may install, operate and maintain the systems.

EXTERNAL OPERATION • Do not install near power lines, telephone lines or guy wires. • Do not install on a wet or windy day, or when lightning or thunder is in the area and do not use metal

ladder. • For the external operations to be executed on the equipments, all the necessary safety rules against

accidental fallings of the operators must be respected, according to the force rules; for example it is necessary to use protection fences and belts. Wear shoes with rubber soles and heels, protective clothing including a long-sleeved shirt and rubber gloves.

• During installation, when the equipments are lifted, it is strictly forbidden to stay or to pass in the underlying area. Such an area must be properly restricted or signalled according to the on force rules.

• During the equipment starting up phase, the operators must not be in front of the antenna INTERNAL OPERATION • For the internal operations wear shoes with rubber soles and heels, protective clothing including a long-

sleeved shirt and rubber gloves. • In order avoid any demage while handling the modules, the user should wear an antistatic elastic

bracelet, grounded by means a spiral cord. • Before supplying the equipment, it is necessary to complete the wiring of the connections to the

protection ground, the insertion of all the units and/or modules provided fot the requested configuration and also the connection of all the necessary connectors.

• The connection to the protection ground must not be removed or damaged. • Handle carefully the optical fiber. • A broken optical fiber can cause damages to eyes and skin, do not point to the eyes a broken fiber or an

incomplete one or an optical connector not covered. • If the optical source is not surely switched off, do not directly or for reflection stare (particulary using

lenses or by means af a microscope) at a broken fiber or at an incomplete one or at an optical connector not covered and do not execute or interrupt an optical connection.

• Do not connect a fiber to an optical output without checking that the fiber terminal is ended and do not supply the optical tributary out of the sub-rack and do not change the factory settings and adjustments.

Non-observance of the safety instructions can result in personal injury or in property demage.

Dept.: CMO-GS-NI-SE Date: 31-05-2006 Ed.: 02 Var.: 06-07 Name: A. Vergani

Exec.: A. Vergani Check: M. Brambilla Ed.: 01 Emiss.: 05-06 Name: A. Vergani

IMC 6011BEDG

SRAL XD Single - Board 2

LOW CAPACITY DIGITAL RADIO SYSTEM

INDEX Sheet 1 / 8

SRAL XD Single – Board 2

7 ... 38 GHz


INSTALLATION INFORMATION MANUAL (This document do not contain information on commercial availability)

IMC 6011BEDG - Ed. 02

The information in this document is subject to change without notice and describes only the product defined in the introduction of this documentation. This documentation is intended for the use of Nokia Siemens Networks customers only for the purposes of the agreement under which the document is submitted, and no part of it may be used, reproduced, modified or transmitted in any form or means without the prior written permission of Nokia Siemens Networks. The documentation has been prepared to be used by professional and properly trained personnel, and the customer assumes full responsibility when using it. Nokia Siemens Networks welcomes customer comments as part of the process of continuous development and improvement of the documentation.

The information or statements given in this documentation concerning the suitability, capacity, or performance of the mentioned hardware or software products are given “as is” and all liability arising in connection with such hardware or software products shall be defined conclusively and finally in a separate agreement between Nokia Siemens Networks and the customer. However, Nokia Siemens Networks has made all reasonable efforts to ensure that the instructions contained in the document are adequate and free of material errors and omissions. Nokia Siemens Networks will, if deemed necessary by Nokia Siemens Networks, explain issues which may not be covered by the document.

Nokia Siemens Networks will correct errors in this documentation as soon as possible. IN NO EVENT WILL NOKIA SIEMENS NETWORKS BE LIABLE FOR ERRORS IN THIS DOCUMENTATION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES,SUCH AS BUT NOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY OR DATA,THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE INFORMATION IN IT.

This documentation and the product it describes are considered protected by copyrights and other intellectual property rights according to the applicable laws.

The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademark of Nokia Corporation. Siemens is a registered trademark of Siemens AG.

Other product names mentioned in this document may be trademarks of their respective owners, and they are mentioned for identification purposes only.

Copyright © Nokia Siemens Networks 2007. All rights reserved.

FOR INTERNAL USE ONLY - FOR INTERNAL USE ONLY




IMC 6011BEDG


LOW CAPACITY DIGITAL RADIO SYSTEM INDEX Sheet 2

INSTALLATION INFORMATION

• Name of the Radio System = SRAL XD (Single – Board 2)

• Frequency Band = 7 - 8 - 13 - 15 - 18 23 - 26 - 28 - 32 - 38 GHz

• Capacity = up to 8 or 16 x 2 Mb/s

• Configurations = 1+0 1+1 Hot-Standby





IMC 6011BEDG



INDEX

1. ODU-ANTENNA INTEGRATED SYSTEM (7 to 38 GHz) (IMC 0354BEDG - Ed. 02)

- 1+0 Configuration (Terminal) Sheet 1

- 1+1 Configuration with 2 Antennas HSBY (Terminal) Sheet 2

- Integrated Antennas for SRA L Sheet 3

- Revision List Sheet 4

2. 1+1 SUPPORTING FRAME-ANTENNA INTEGRATED SYSTEM (7 to 38 GHz) (IMC 0355BEDG - Ed. 02)

- 1+1 Configuration HSBY (Terminal) Sheet 1

- Dimensions Sheet 2 - Protection Covers and O-Rings Sheet 3

- Polarization change Sheet 4

- P/N, Attenuation and Flange Sheet 5

- Integrated Antennas for SRA L Sheet 6 - Revision List Sheet 7

3. VERTICAL 1+0 FRAME NOT INTEGRATED SYSTEM (7 to 38 GHz) (IMC 0356BEDG - Ed. 02)

- 1+0 Configuration (Terminal) Sheet 1 - 1+1 Configuration with 2 Antennas HSBY (Terminal) Sheet 2 - Dimensions Sheet 3 - Pole fixing Sheet 4 - Wall fixing Sheet 5 - Protection Cover and O-rings Sheet 6 - P/N and Flange Sheet 7 - Integrated Antennas for SRA L Sheet 8 - Revision List Sheet 9





IMC 6011BEDG



4. 1+1 FRAME NOT INTEGRATED SYSTEM (7 to 38 GHz) (IMC 0358BEDG - Ed. 02) - 1+1 Configuration HSBY (Terminal) Sheet 1

- Dimensions Sheet 2

- Pole fixing Sheet 3

- Wall fixing Sheet 4

- Protection Cover and O-rings Sheet 5 - P/N, Attenuation and Flange Sheet 6 - Integrated Antennas for SRA L Sheet 7


5. NOT INTEGRATED SYSTEM

SOLUTION WITH FLEXIBLE WAVEGUIDE (IMC 0254BEDG - Ed. 07) - Connection Sheet 1

- Connection with antennas ø >1.8 mt for 7-13 GHz Sheet 2

- P/N and Attenuation Sheet 3

- Pole overall size Sheet 4






IMC 6011BEDG



6. NOT INTEGRATED SYSTEM SOLUTION WITH ELLIPTICAL WAVEGUIDE (IMC 0255BEDG - Ed. 07)

- Connection for Single Polarization Sheet 1

- Connection with Antennas Ø > 1.8m for 7-13 GHz Sheet 2

- Pressurization with external dehydrator Sheet 3

- P/N Sheet 4


7. OUTDOOR ASSEMBLY (IMC 0256BEDG - Ed. 08) - Assembly on Support Frame Sheet 1

- Normal Density and High Density Enhanced Sheet 2

- Normal Density 2 Sheet 3

- Shifter, P/N and Flange Sheet 4

- Vertical/Horizontal Polarization Application for Normal Density and High Density Enhanced Sheet 5

- Vertical/Horizontal Polarization Application for Normal Density 2 Sheet 6

- “Rx Field Measure” Connector Sheet 7


8. BRAIDED COAXIAL CABLE (IMC 0257BEDG - Ed. 08) - Typical Connection Sheet 1

- Grounding Connections, Integrated Solution Sheet 2

- Grounding Connections, Not Integrated Solution Sheet 3

- Pole Fixing of the Grounding Plate Kit Sheet 4

- Typical fixing Sheet 5

- Fixing rules Sheet 6

- Coaxial cable and connection kit Sheet 7

- Characteristics Sheet 8






IMC 6011BEDG



9. 1/4” COAXIAL CABLE (IMC 0258BEDG - Ed. 08) - Typical Connection Sheet 1

- Connection on ODU Side Sheet 2

- Grounding Connections, Integrated Solution Sheet 3

- Grounding Connections, Not Integrated Solution Sheet 4

- Pole Fixing of the Grounding Plate Kit Sheet 5

- Typical Fixing Sheet 6

- Fixing rules Sheet 7

- Connection on IDU side Sheet 8

- Coaxial cable and connection kit Sheet 9

- Characteristics Sheet 10


10. INDOOR ASSEMBLY (IMC 0359BEDG - Ed. 02)

- Rack Assembly Sheet 1

- Grounding Connections Sheet 2

- Mounting Bracket for 19” Rack Sheet 3

- Mounting Bracket for N3 ETSI Rack Sheet 4

- Equipment Sheet 5

- Functions Sheet 6

- Power Supply; Connections and PIN-OUT Sheet 7

- 75/120 Ohm Tributary Unit; Connections and PIN-OUT Sheet 8

- Alarm; Connections and PIN-OUT Sheet 11

- USER 64 Kb/s V11; Connections and PIN-OUT Sheet 13

- LCT (Personal Computer RS-232 Interface); Connections Sheet 14

- QLAN / VLAN 10BaseT – 100BaseTx; Connections and PIN-OUT Sheet 16

- IP Phone (48Vdc/220 Vac); Connection Sheet 19






IMC 6011BEDG



11. 2 Mbit/s DIGITAL DISTRIBUTION FRAME (IMC 0360BEDG - Ed. 02) - Digital Distribution Frame (120 and 75 Ohm) Lay-Out Sheet 1 - Digital Distribution Frame (120 Ohm) Connection Sheet 2 - Digital Distribution Frame (120 Ohm) Wiring Sheet 3 - Digital Distribution Frame (75 Ohm) Connection Sheet 4 - Digital Distribution Frame (75 Ohm) Wiring Sheet 5 - Revision List Sheet 6

12. ASSEMBLING INDOOR ACCESSORIES (IMC 0260BEDG - Ed. 06)

- Power Supply Connector Sheet 1 - Power Supply Connector with 2x1,5 mm² Bipolar Shielded Power Supply Cable Sheet 2 - Sub-D 50 Contacts Connector with 75 Ohm Coaxial Cable

(only if do not use the standard solution of assembled cable) Sheet 5 - Sub-D 50 Contacts Connector with Multipairs Cable (Metallic Shell)

(only if do not use the standard solution of assembled cable) Sheet 7 - Sub-D 9-15 Contacts Connector with Multipairs Cable (Shielded Shell) Sheet 9 - Metallic Shell Sheet 11 - Shielded Shell Sheet 15 - Self Locking Coaxial Plug Sheet 19 - RJ 45 Shielded Connector with cable Sheet 21 - Revision List Sheet 24

13. INSTALLATION MATERIALS (IMC 0361BEDG - Ed. 02)

- Standard installation materials for 2 Mb/s 75 Ohm (Sub-D) Tributary Sheet 1 - Standard installation materials for 2 Mb/s 120 Ohm (Sub-D) Tributary Sheet 2 - Optional Sheet 3 - Compositions Sheet 4 - Revision List Sheet 6

14. SPECIAL TOOLS (IMC 0262BEDG - Ed. 06)

- User table Sheet 1 - Crimping Tool for Power Supply Connector Sheet 2 - Crimping Tool for Coaxial Plug Sheet 3 - Crimping Tool RJ45 Connector Sheet 4 - Cable Stripping Tool for Grounding Kit Sheet 5 - Strap Plier Sheet 6 - Wire Cut and Strip Tool for 120 Ohm wire-wrap DDF Sheet 7 - Hand wrapping Tool for 120 Ohm wire-wrap DDF Sheet 8 - Revision List Sheet 9





IMC 6011BEDG



SRAL XD Single Board 2 LOW CAPACITY DIGITAL RADIO SYSTEM

MANUAL REVISION LIST

Revisions Document 01 02 03 04 05 06 07 08 09 10

IMC 6011BEDG ¯ ¯ IMC 0354BEDG ¯ ¯ IMC 0355BEDG ¯ ¯ IMC 0356BEDG ¯ ¯ IMC 0358BEDG ¯ ¯ IMC 0254BEDG ¯ ¯ ¯ ¯ ¯ ¯ ¯ IMC 0255BEDG ¯ ¯ ¯ ¯ ¯ ¯ ¯ IMC 0256BEDG ¯ ¯ ¯ ¯ ¯ ¯ ¯ ¯ IMC 0257BEDG ¯ ¯ ¯ ¯ ¯ ¯ ¯ ¯ IMC 0258BEDG ¯ ¯ ¯ ¯ ¯ ¯ ¯ ¯ IMC 0359BEDG ¯ ¯ IMC 0360BEDG ¯ ¯ IMC 0260BEDG ¯ ¯ ¯ ¯ ¯ ¯ IMC 0361BEDG ¯ ¯ IMC 0262BEDG ¯ ¯ ¯ ¯ ¯ ¯



19" or N3 ETSI RACK

INDOOR ASSEMBLY(See IMC 0359BEDG)

(See IMC 0359BEDG)

1+0 CONFIGURATION

ODU-ANTENNA INTEGRATED SYSTEM (7 to 38 GHz)




CMO-GS-NI-SE

A. Vergani

Dept.:

Exec.:

Date:

Check:

31-05-2006

M. Brambilla

IMC 0354BEDG

Sheet 1/4

Name:

Name:

Var.:

Emiss.:

Ed.:

Ed.: 01 05-06 A. Vergani

(Terminal)

FOR LENGHT UP TO 300 mt. THE 1/4" COAX CABLE IS AVAILABLE ON REQUEST (REFER TO IMC 0258BEDG)a) = CABLE FORESEEN AS STANDARD SUPPLY (MAX LENGHT= 200 mt.)

SINGLE-BOARD

BRAIDED COAXIAL CABLE (a)(See IMC 0257BEDG)

INTEGRATED ANTENNA

(See Sheet 3)for SRA L

(See IMC 0256BEDG)OUTDOOR ASSEMBLY

INSTALLATION INFORMATION for

ALMs

s

LCTQ-LANUSER

SRAL XD

V-LAN

2 Mbit/s I/O TRIBUTARIES1-8

OD

CBLU

ODU CABLE

CH

ET

ST

C

M/NM

/

JW

-+

PS

02 06-07 A. Vergani



CMO-GS-NI-SE

A. Vergani

Dept.:

Exec.:

Date:

Check:

31-05-2006

M. Brambilla

IMC 0354BEDG

Sheet 2

Name:

Name:

Var.:

Emiss.:Ed.: 01 05-06 A. Vergani

a) = CABLE FORESEEN AS STANDARD SUPPLY (MAX LENGHT= 200 mt.)FOR LENGHT UP TO 300 mt. THE 1/4" COAX CABLE IS AVAILABLE ON REQUEST (REFER TO IMC 0258BEDG)

ODU-ANTENNA INTEGRATED SYSTEM (7 to 38 GHz)INSTALLATION INFORMATION for LOW CAPACITY DIGITAL RADIO SYSTEMSRAL XD Single - Board 2

19" or N3 ETSI RACK(See IMC 0359BEDG)

SINGLE-BOARD

(See IMC 0359BEDG)INDOOR ASSEMBLY

ODU-ANTENNA INTEGRATED SYSTEM (7 to 38 GHz)1+1 CONFIGURATION WITH 2 ANTENNAS

Hot-Stand By

for SRA L(See Sheet 3)

INTEGRATED ANTENNA

OUTDOOR ASSEMBLY(See IMC 0256BEDG)

BRAIDED COAXIAL CABLE (See IMC 0257BEDG)

(a)

(Terminal)

ALMs

sLCT

Q-LANUSER

SRAL XD

V-LAN

2 Mbit/s I/O TRIBUTARIES1-8 9-16

ODU

CB C

HL

ODU CABLEOD

CBLU

ODU CABLE

CH

ET

ST

C

M/NM

/

JW

-+

PS

02 06-07 A. VerganiEd.:





IMC 0354BEDG


LOW CAPACITY DIGITAL RADIO SYSTEM INSTALLATION INFORMATION for

ODU-ANTENNA INTEGRATED SYSTEM (7 to 38 GHz) Sheet 3

ODU-ANTENNA INTEGRATED SYSTEM (7 to 38 GHz) INTEGRATED ANTENNAS for SRA-L

ANTENNA DIAMETER (m)

P/N FREQUENCY BAND (GHz)

0,2 0,3 0,6 0,8 1,2

FEEDER FLANGE

7 - - 601-060/07 - 601-120/07 PDR 84

8 - - 601-060/07 - 601-120/07 PDR 84

13 - - 601-060/13 601-080/13 601-120/13 PBR 120

15 - 601-030/15 601-060/15 601-080/15 601-120/15 PBR 140

18 - 601-030/18 601-060/18 601-080/18 601-120/18 PBR 220

23 601-020/23 601-030/23 601-060/23 601-080/23 601-120/23 PBR 220

26 601-020/26 601-030/26 601-060/26 601-080/26 601-120/26 PBR 220

28 601-030/28 601-060/28 PBR 320

32 601-030/32 601-060/32 PBR 320

38 601-020/38 601-030/38 601-060/38 - - PBR 320





IMC 0354BEDG



ODU-ANTENNA INTEGRATED SYSTEM (7 to 38 GHz) Sheet 4


REVISION LIST

Revisions Revisions Sheet 01 02 03 04 05 06 07 08 09 10

Sheet 01 02 03 04 05 06 07 08 09 10

01 ¯ ¯ - 02 ¯ ¯ - 03 ¯ ¯ - 04 ¯ ¯ - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -



CMO-GS-NI-SE

A. Vergani

Dept.:

Exec.:

Date:

Check:

31-05-2006

M. Brambilla

IMC 0355BEDG

Sheet 1/7

Name:

Name:

Var.:


1+1 CONFIGURATION

1+1 SUPPORTING FRAME-ANTENNA INTEGRATED SYSTEM (7 to 38 GHz)

Hot-StandBy

FOR LENGHT UP TO 300 mt. THE 1/4" COAX CABLE IS AVAILABLE ON REQUEST (REFER TO IMC 0258BEDG)a) = CABLE FORESEEN AS STANDARD SUPPLY (MAX LENGHT= 200 mt.)

SRAL XD Single - Board 2LOW CAPACITY DIGITAL RADIO SYSTEM

INSTALLATION INFORMATION for 1+1 SUPPORTINGFRAME-ANTENNA INTEGRATED SYSTEM (7 to 38 GHz)

(Terminal)

(See IMC 0359BEDG)

(See IMC 0359BEDG)19" or N3 ETSI RACK

INDOOR ASSEMBLYSINGLE-BOARD

sLCT

ALMs

SRAL XD

USER Q-LAN V-LAN

+ -


ODU CABLE

LBC

UDO

HC

ODU CABLE

UDO

HC

LBC

W

MN/

TS

TE

J

/M

CPS

(See IMC 0257BEDG)BRAIDED COAXIAL CABLE (a)


1+1 INTEGRATED SUPPORTING FRAME(See Sheet 2 to 5)

(See Sheet 6)

INTEGRATED ANTENNA

(b)

for SRA L




CMO-GS-NI-SE

A. Vergani

Dept.:

Exec.:

Date:

Check:

31-05-2006

M. Brambilla

IMC 0355BEDG

Sheet 2

Name:

Name:

Var.:


DIMENSIONS



LOW CAPACITY DIGITAL RADIO SYSTEMSRAL XD Single - Board 2

a) = OVERALL DIMENSIONS INCLUDING ODUb) = FOR P/N See Sheet 5

DIMENSIONS IN MILLIMETERS (mm)


1+1 SUPPORTING FRAME(b)

550

mm

(OD

U N

D/H

De)

(a)

450

mm

(OD

U N

D2)

(a

) or

ODU(See IMC 0256BEDG)

ODU SAFETYHOOK

POLE Ø 75÷115

UPMAIN

HSBYDOWN



CMO-GS-NI-SE

A. Vergani

Dept.:

Exec.:

Date:

Check:

31-05-2006

M. Brambilla

IMC 0355BEDG

Sheet 3

Name:

Name:

Var.:




a) = THE O-RINGS ARE DELIVERED WITH THE FRAME

1+1 SUPPORTING FRAME ANTENNA INTEGRATED SYSTEM (7 to 38GHz)PROTECTION COVERS and O-RINGS

PROTECTION COVER

O-RING(a)PROTECTION COVER




CMO-GS-NI-SE

A. Vergani

Dept.:

Exec.:

Date:

Check:

31-05-2006

M. Brambilla

IMC 0355BEDG

Sheet 4

Name:

Name:

Var.:


POLARIZATION CHANGE


V

H

VERTICAL POLARIZATION

V

H

HORIZONTAL POLARIZATION

STEP TWIST

THE POLARIZATION CHANGE CAN BE EXECUTED LOOSENING THE FIXING SCREW/SCREWSOF THE STEP TWIST AND ROTATING THE DISK UNTIL TO ALIGN THE REFERENCE NOTCHESON THE DESIRED POLARIZATION.AT THE END OF THE OPERATION ONLY, TIGHTEN THE SCREW/SCREWS TAKING CAREOF THE ALIGNMENT OF THE REFERENCE NOTCHES.

POLARIZATION CHANGE



STEP TWIST






IMC 0355BEDG


LOW CAPACITY DIGITAL RADIO SYSTEM INSTALLATION INFORMATION for 1+1 SUPPORTING

FRAME-ANTENNA INTEGRATED SYSTEM (7 to 38 GHz) Sheet 5

1+1 SUPPORTING FRAME-ANTENNA INTEGRATED SYSTEM (7 to 38 GHz) P/N, ATTENUATION and FLANGE

1+1 FRAME UNBALANCED HSBY

1+1 FRAME BALANCED HSBY

COUPLING ATTENUATION

(dB)

FREQ. BAND (GHz)

P/N

MAIN ST.BY

P/N COUPLING

ATTENUATION (dB)

FRAME FLANGE

(to Antenna)

7/8 534-120/07 1.0 10±1 534-120/17 3±0.3 UBR 84

13 534-120/09 1.2 10±1 534-120/19 3±0.3 UBR 120

15 534-120/01 1.3 10±1 534-120/11 3±0.3 UBR 140

18 534-120/02 1.3 10±1 534-120/12 3±0.3 UBR 220

23 534-120/03 1.3 10±1 534-120/13 3±0.3 UBR 220

26 534-120/04 1.3 10±1 534-120/14 3±0.3 UBR 220

28 534-120/05 1.3 10±1 534-120/15 3±0.3 UBR 320

32 534-120/10 1.3 10±1 534-120/20 3±0.3 UBR 320

38 534-120/06 1.3 10±1 534-120/16 3±0.3 UBR 320





IMC 0355BEDG




1+1 SUPPORTING FRAME-ANTENNA INTEGRATED SYSTEM (7 to 38 GHz) INTEGRATED ANTENNAS for SRAL

ANTENNA DIAMETER (m) P/N FREQUENCY

BAND (GHz)

0.3 0.6 0.8 1.2

FEEDER FLANGE

7 - 601-060/07 - 601-120/07 PDR 84

8 - 601-060/08 - 601-120/08 PDR 84

13 - 601-060/13 601-080/13 601-120/13 PBR 120

15 601-030/15 601-060/15 601-080/15 601-120/15 PBR 140

18 601-030/18 601-060/18 601-080/18 601-120/18 PBR 220

23 601-030/23 601-060/23 601-080/23 601-120/23 PBR 220

26 601-030/26 601-060/26 601-080/26 601-120/26 PBR 220

28 601-030/28 601-060/28 - - PBR 320

32 601-030/32 601-060/32 - - PBR 320

38 601-030/38 601-060/38 - - PBR 320





IMC 0355BEDG





REVISION LIST


Sheet 01 02 03 04 05 06 07 08 09 10

01 ¯ ¯ - 02 ¯ ¯ - 03 ¯ ¯ - 04 ¯ ¯ - 05 ¯ ¯ - 06 ¯ ¯ - 07 ¯ ¯ - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -



(Terminal)1+0 CONFIGURATION

VERTICAL 1+0 FRAME NOT INTEGRATED SYSTEM (7 to 38 GHz)


CMO-GS-NI-SE

A. Vergani

Dept.:

Exec.:

Date:

Check:

31-05-2006

M. Brambilla

IMC 0356BEDG

Sheet 1/9

Name:

Name:

Var.:


b) = FOR ELLIPTICAL WAVEGUIDE CONNECTION see IMC 0255BEDG


NOT INTEGRATED SYSTEM (7 to 38 GHz)INSTALLATION INFORMATION for VERTICAL 1+0 FRAME


ALMs

s

Q-LANUSER

SRAL XD

V-LAN LCT

2 Mbit/s I/O TRIBUTARIES1-8

OD

CBLU

ODU CABLE

CH

ET

ST

C

M/NM

/

JW

-+

PS

19" or N3 ETSI RACK(See IMC 0359BEDG)

SINGLE-BOARD



(See Sheets 3÷7)

(a)(See IMC 0257BEDG)

BRAIDED COAXIAL CABLE

INTEGRATED ANTENNA

FLEXIBLE WAVEGUIDE(See IMC 0254BEDG)

VERTICAL 1+0 FRAME

(b)

(See Sheet 8)for SRA L




Hot-Stand By1+1 CONFIGURATION WITH 2 ANTENNAS


CMO-GS-NI-SE

A. Vergani

Dept.:

Exec.:

Date:

Check:

31-05-2006

M. Brambilla

IMC 0356BEDG

Sheet 2

Name:

Name:

Var.:


b) = FOR ELLIPTICAL WAVEGUIDE CONNECTION see IMC 0255BEDG


LOW CAPACITY DIGITAL RADIO SYSTEMINSTALLATION INFORMATION for VERTICAL 1+0 FRAME

NOT INTEGRATED SYSTEM (7 to 38 GHz)


(Terminal)

sLCT

ALMs

SRAL XD

USER Q-LAN V-LAN

(See IMC 0359BEDG)

+ -


ODU CABLE

LBC

UDO

HC

ODU CABLE

UDO

HC

LBC

W

MN/

TS

TE

J

/M

CPS




(a)(See IMC 0257BEDG)



INTEGRATED ANTENNA

(See Sheet 8)

(See Sheets 3÷7)VERTICAL 1+0 FRAME


(b)

for SRA L



DIMENSIONS


CMO-GS-NI-SE

A. Vergani

Dept.:

Exec.:

Date:

Check:

31-05-2006

M. Brambilla

IMC 0356BEDG

Sheet 3

Name:

Name:

Var.:


a) = OVERALL DIMENSIONS INCLUDING ODUb) = FOR P/N See Sheet 7





210230.5107.515 to 38

A

147.57 to 13

ND/HDeB

270.5

ND2

250


Ø75÷115mm POLE

1+0 FRAME(b)

(See IMC 0256BEDG)ODU



POLE FIXING


CMO-GS-NI-SE

A. Vergani

Dept.:

Exec.:

Date:

Check:

31-05-2006

M. Brambilla

IMC 0356BEDG

Sheet 4

Name:

Name:

Var.:





Ø75÷115mm POLE

1+0 FRAME




WALL FIXING


CMO-GS-NI-SE

A. Vergani

Dept.:

Exec.:

Date:

Check:

31-05-2006

M. Brambilla

IMC 0356BEDG

Sheet 5

Name:

Name:

Var.:


a) = THE INSERTS ARE NOT DELIVERED WITH THE FRAME, IF THIS FIXING IS REQUESTED THEY HAVE TO BE SEPARATELY PROVIDED




1+0 FRAME

INSERT(a)




PROTECTION COVER and O-RINGS


CMO-GS-NI-SE

A. Vergani

Dept.:

Exec.:

Date:

Check:

31-05-2006

M. Brambilla

IMC 0356BEDG

Sheet 6

Name:

Name:

Var.:






PROTECTION COVER

(a) O-RING

PROTECTION COVER






IMC 0356BEDG


LOW CAPACITY DIGITAL RADIO SYSTEM INSTALLATION INFORMATION for VERTICAL 1+0 FRAME

NOT INTEGRATED SYSTEM (7 to 38 GHz) Sheet 7

VERTICAL 1+0 FRAME NOT INTEGRATED SYSTEM (7 to 38 GHz) P/N and FLANGE

FREQUENCY BAND (GHz)

1+0 FRAME P/N

FRAME FLANGE (to Antenna)

7 534-108/69 UDR 84

8 534-108/69 UDR 84

13 534-108/71 UBR 120

15 534-108/72 UBR 140

18 534-108/73 UBR 220

23 534-108/73 UBR 220

26 534-108/73 UBR 220

28 534-108/74 UBR 320

32 534-108/74 UBR 320

38 534-108/74 UBR 320





IMC 0356BEDG




VERTICAL 1+0 FRAME NOT INTEGRATED SYSTEM (7 to 38 GHz) INTEGRATED ANTENNAS for SRA L



0,2 0,3 0,6 0,8 1,2

FEEDER FLANGE

7 - - 601-060/07 - 601-120/07 PDR 84

8 - - 601-060/07 - 601-120/07 PDR 84

13 - - 601-060/13 601-080/13 601-120/13 PBR 120

15 - 601-030/15 601-060/15 601-080/15 601-120/15 PBR 140

18 - 601-030/18 601-060/18 601-080/18 601-120/18 PBR 220

23 601-020/23 601-030/23 601-060/23 601-080/23 601-120/23 PBR 220

26 601-020/26 601-030/26 601-060/26 601-080/26 601-120/26 PBR 220

28 - 601-030/28 601-060/28 PBR 320

32 - 601-030/32 601-060/32 PBR 320

38 601-020/38 601-030/38 601-060/38 - - PBR 320





IMC 0356BEDG





REVISION LIST


Sheet 01 02 03 04 05 06 07 08 09 10

01 ¯ ¯ - 02 ¯ ¯ - 03 ¯ ¯ - 04 ¯ ¯ - 05 ¯ ¯ - 06 ¯ ¯ - 07 ¯ ¯ - 08 ¯ ¯ - 09 ¯ ¯ - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -




1+1 FRAME NOT INTEGRATED SYSTEM (7 to 38 GHz)


CMO-GS-NI-SE

A. Vergani

Dept.:

Exec.:

Date:

Check:

31-05-2006

M. Brambilla

IMC 0358BEDG

Sheet 1/8

Name:

Name:

Var.:


(b) = FOR ELLIPTICAL WAVEGUIDE CONNECTION see IMC 0255BEDG

(a) = CABLE FORESEEN AS STANDARD SUPPLY (MAX LENGHT= 200 mt.)FOR LENGHT UP TO 300 mt. THE 1/4" COAX CABLE IS AVAILABLE ON REQUEST (REFER TO IMC 0258BEDG)

1+1 FRAME NOT INTEGRATED SYSTEM (7 to 38GHz)1+1 CONFIGURATION

Hot-Stand By(Terminal)

INSTALLATION INFORMATION for

sLCT

ALMs

SRAL XD

USER Q-LAN V-LAN

(See IMC 0359BEDG)

+ -


ODU CABLE

LBC

UDO

HC

ODU CABLE

UDO

HC

LBC

W

MN/

TS

TE

J

/M

CPS



- NOTE -

IF YOU WANT TO PASS TOTHE 1+1 INTEGRATED SYSTEM,

ORDER THE KIT 332-056/22


BRAIDED COAXIAL CABLE (See IMC 0257BEDG)

(a)

for SRAL XD(See Sheet 7)

INTEGRATED ANTENNA


(b)

(See Sheets 2÷6)1+1 FRAME




CMO-GS-NI-SE

A. Vergani

Dept.:

Exec.:

Date:

Check:

31-05-2006

M. Brambilla

IMC 0358BEDG

Sheet 2

Name:

Name:

Var.:


1+1 FRAME NOT INTEGRATED SYSTEM (7 to 38GHz)DIMENSIONS

a) = OVERALL DIMENSIONS INCLUDING ODUb) = FOR P/N see Sheet 6


INSTALLATION INFORMATION for1+1 FRAME NOT INTEGRATED SYSTEM (7 to 38 GHz)



(b) 1+1 FRAME

(See IMC 0256BEDG)



CMO-GS-NI-SE

A. Vergani

Dept.:

Exec.:

Date:

Check:

31-05-2006

M. Brambilla

IMC 0358BEDG

Sheet 3

Name:

Name:

Var.:


1+1 FRAME NOT INTEGRATED SYSTEM (7 to 38GHz)POLE FIXING



1+1 FRAME

Ø75÷115mm POLE




CMO-GS-NI-SE

A. Vergani

Dept.:

Exec.:

Date:

Check:

31-05-2006

M. Brambilla

IMC 0358BEDG

Sheet 4

Name:

Name:

Var.:


1+1 FRAME NOT INTEGRATED SYSTEM (7 to 38GHz)WALL FIXING

a) = THE INSERTS ARE NOT DELIVERED WITH THE FRAME, IF THIS FIXING IS REQUESTED THEY HAVE TOBE SEPARATELY PROVIDED



INSERT(a)




CMO-GS-NI-SE

A. Vergani

Dept.:

Exec.:

Date:

Check:

31-05-2006

M. Brambilla

IMC 0358BEDG

Sheet 5

Name:

Name:

Var.:


1+1 FRAME NOT INTEGRATED SYSTEM (7 to 38GHz)O-RINGS




O-RING(a)

PROTECTION COVER

PROTECTION COVER






IMC 0358BEDG



1+1 FRAME NOT INTEGRATED SYSTEM (7 to 38 GHz) Sheet 6

1+1 FRAME NOT INTEGRATED SYSTEM (7 to 38 GHz) P/N, ATTENUATION and FLANGE

1+1 FRAME UNBALANCED HSBY

1+1 FRAME BALANCED HSBY

COUPLING ATTENUATION

(dB)

FREQ. BAND

(GHz) P/N

MAIN ST.BY

P/N COUPLING

ATTENUATION (dB)

FRAME FLANGE

(to Antenna)

7 534-121/07 1.1 10±1 534-121/17 3±0.3 UDR 84

8 534-121/07 1.2 10±1 534-121/17 3±0.3 UDR 84

13 534-121/09 1.2 10±1 534-121/19 3±0.3 UBR 120

15 534-121/01 1.3 10±1 534-121/11 3±0.3 UBR 140

18 534-121/02 1.3 10±1 534-121/12 3±0.3 UBR 220

23 534-121/03 1.3 10±1 534-121/13 3±0.3 UBR 220

26 534-121/04 1.3 10±1 534-121/14 3±0.3 UBR 220

28 534-121/05 1.3 10±1 534-121/15 3±0.3 UBR 320

32 534-121/10 1.3 10±1 534-121/20 3±0.3 UBR 320

38 534-121/06 1.3 10±1 534-121/16 3±0.3 UBR 320





IMC 0358BEDG




1+1 FRAME NOT INTEGRATED SYSTEM (7 to 38 GHz) INTEGRATED ANTENNAS for SRAL



0.2 0.3 0.6 0.8 1.2

FEEDER FLANGE

7 601-060/07 601-120/07 PDR 84

8 601-060/07 601-120/07 PDR 84

13 601-060/13 601-080/13 601-120/13 PBR 120

15 - 601-030/15 601-060/15 601-080/15 601-120/15 PBR 140

18 - 601-030/18 601-060/18 601-080/18 601-120/18 PBR 220

23 601-020/23 601-030/23 601-060/23 601-080/23 601-120/23 PBR 220

26 601-020/26 601-030/26 601-060/26 601-080/26 601-120/26 PBR 220

28 601-030/28 601-060/28 601-080/28 601-120/28 PBR 320

32 601-030/32 601-060/32 PBR 320

38 601-020/38 601-030/38 601-060/38 - - PBR 320





IMC 0358BEDG




1+1 FRAME NOT INTEGRATED SYSTEM (7 to 38 GHz)

REVISION LIST


Sheet 01 02 03 04 05 06 07 08 09 10

01 ¯ ¯ - 02 ¯ ¯ - 03 ¯ ¯ - 04 ¯ ¯ - 05 ¯ ¯ - 06 ¯ ¯ - 07 ¯ ¯ - 08 ¯ ¯ - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -



CMO-GS-NI-SE

A. Vergani

Dept.:

Exec.:

Date:

Check:

12-05-2003

M. Brambilla

IMC 0254BEDG

Sheet 1/5

Name:

Name:

Var.:

Emiss.:

Ed.:


SOLUTION WITH FLEXIBLE WAVEGUIDE

SRAL XD

INSTALLATION INFORMATION for NOT INTEGRATED SYSTEMLOW CAPACITY DIGITAL RADIO SYSTEM

NOT INTEGRATED SYSTEMSOLUTION WITH FLEXIBLE WAVEGUIDE

CONNECTION

POLE FIXING forFLEXIBLE WAVEGUIDE

= UNPRESSURIZABLE FLANGE

= PRESSURIZABLE FLANGE

FOR THE OVERALL SIZE see Sheet 4

a) = FOR THE P/N OF THESE ACCESSORIES see Sheet 3b) = IT IS DELIVERED IN Q.TY OF 1 WITH THE 0.6m FLEXIBLE WAVEGUIDE and 2 WITH THAT BY 1m

U

P

(a)

(b)

FLEXIBLE WAVEGUIDE

"VERTICAL" POLARIZATION

"HORIZONTAL" POLARIZATION

U

(recommended Ø 115mm)Ø 75÷115mm POLE

P

P

U

USE ONLY THE SCREWS SUPPLIED WITH

THE ANTENNA

1+0 VERTICAL FRAME

SUPPORTING FRAME WITH PASSING HOLEUSE ONLY THE SCREWS SUPPLIEDWITH THE FLEXIBLE WAVEGUIDE

or

USE ONLY THE SCREWS SUPPLIEDWITH THE SUPPORTING FRAME

SUPPORTING FRAME WITH BLIND HOLE

or

1+1 SUPPORTING FRAME

A. Vergani06-0707



A. VerganiName:

Var.

Emiss.:01

Ed.

Ed.: 05-03

Date:

Check:A. Vergani M.Brambilla

12-05-2003Dept.:

Exec.:

CMO-GS-NI-SE

Sheet 2

IMC 0254BEDGLOW CAPACITY DIGITAL RADIO SYSTEM

INSTALLATION INFORMATION for NOT INTEGRATED SYSTEM

SRAL XD


Name:Var.:Ed.:

NOT INTEGRATED SYSTEMSOLUTION WITH FLEXIBLE WAVE GUIDE

CONNECTION WITH ANTENNAS Ø >1,8m FOR 7 - 13 GHz

A. Vergani06-0707

(b)

FLEXIBLE WAVEGUIDE (L=1000mm)(a)

PU P

U

P UP

"HORIZONTAL" POLARIZATION"VERTICAL" POLARIZATION



P

U

(c) STRAIGHT SECTION STRAIGHT SECTION (c)

Ø 115mm POLE

POLE FIXING for

(13 GHz)

(7 GHz)

PDR 120

PDR 70

U

FLEXIBLE WAVEGUIDE

b) = IT IS DELIVERED IN Q.TY OF 2 WITH THE 1m FLEXIBLE WAVEGUIDEa) = FOR THE P/N OF THESE ACCESSORIES see Sheet 3





IMC 0254BEDG

SRAL XD

LOW CAPACITY DIGITAL RADIO SYSTEM INSTALLATION INFORMATION for NOT INTEGRATED SYSTEM

SOLUTION WITH FLEXIBLE WAVEGUIDE Sheet 3

NOT INTEGRATED SYSTEM

SOLUTION WITH FLEXIBLE WAVEGUIDE P/N and ATTENUATION

FLEXIBLE WAVEGUIDE KIT (L. = 600 mm) (a)

FLEXIBLE WAVEGUIDE KIT (L. = 1000 mm) (b)

FREQUENCY BAND (GHz)

P/N ATTENUATION (dB) P/N ATTENUATION

(dB)

STRAIGHT SECTION (c)

7 597-524/83 (UDR-PDR 84) 0,18

597-523/95 (UDR-PDR 84) 0,39

504-216/01 (UDR70-PDR84)

8 597-524/83 (UDR-PDR 84) 0,18

597-523/95 (UDR-PDR 84) 0,39 -

13 597-524/85

(UBR-PBR 120) (d)

0,3 597-523/97

(UBR-PBR 120) (d)

0,5 504-216/24

(UDR-PBR120)

15 597-524/86

(UBR-PBR 140) (d)

0,396 597-523/98

(UBR-PBR 140) (d)

0,66

18 597-524/87 (UBR-PBR 220) 0,72

597-523/99 (UBR-PBR 220) 1,2

23 597-524/87 (UBR-PBR 220) 0,72

597-523/99 (UBR-PBR 220) 1,2

26 597-524/87 (UBR-PBR 220) 0,72

597-523/99 (UBR-PBR 220) 1,2

28 597-525/79 (UBR-PBR 320) 1,2

597-525/80 (UBR-PBR 320) 2

32 597-526/72 (UBR-PBR 320) 1,76

597-526/73 (UBR-PBR 320) 3,28

38 597-524/88 (UBR-PBR 320) 1,2

597-524/20 (UBR-PBR 320)

2

a) = THIS FLEXIBLE WAVEGUIDE IS USED WITH ANTENNAS DIAMETERS UP TO 0.80 mt (2.5 ft.)

b) = THIS FLEXIBLE WAVEGUIDE IS USED WITH ANTENNAS DIAMETERS FROM 1.2 mt (4 ft.)

c) = THIS STRAIGHT SECTION IS USED WITH ANTENNAS DIAMETERS FROM 1.8 mt (6 ft.) d) = SPECIAL (UBR) FLANGE



CMO-GS-NI-SE

A. Vergani

Dept.:

Exec.:

Date:

Check:

12-05-2003

M. Brambilla

IMC 0254BEDG

Sheet 4

Name:Emiss.:Ed.: 01 05-03 A. Vergani


SRAL XD

INSTALLATION INFORMATION for NOT INTEGRATED SYSTEMLOW CAPACITY DIGITAL RADIO SYSTEM

NOT INTEGRATED SYSTEMSOLUTION WITH FLEXIBLE WAVEGUIDE

POLE OVERALL SIZE


ANTENNAS UP TO Ø80 cm

800

800

1000

1000

1+0 7÷38 GHz WITH 1+1 7÷38 GHz WITHANTENNAS UP TO Ø80 cm

ANTENNAS Ø 1,2 m1+0 7÷38 GHz WITH 1+1 7÷38 GHz WITH

ANTENNAS Ø 1,2 m

Name:Var.:Ed.: 07 06-07 A. Vergani





IMC 0254BEDG

SRAL XD

LOW CAPACITY DIGITAL RADIO SYSTEM INSTALLATION INFORMATION for NOT INTEGRATED SYSTEM

SOLUTION WITH FLEXIBLE WAVEGUIDE Sheet 5

NOT INTEGRATED SYSTEM SOLUTION WITH FLEXIBLE WAVEGUIDE

REVISIONS LIST


Sheet 01 02 03 04 05 06 07 08 09 10

01 ¯ ¯ ¯ ¯ ¯ ¯ ¯ - 02 ¯ ¯ ¯ ¯ ¯ ¯ - 03 ¯ ¯ ¯ ¯ ¯ - 04 ¯ ¯ ¯ ¯ ¯ ¯ ¯ - 05 ¯ ¯ ¯ - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -



iTWIST(NB1)

g"E" BEND 90°(NB1)

aWAVEGUIDE

(NB1)CONNECTOR

dNB1

WAVEGUIDE SUPPORT

(NB1)fe and RUBBER BUSHUNIVERSAL CLAMP

P

CONNECTION for SINGLE POLARIZATION

"VERTICAL" POLARIZATION

"HORIZONTAL" POLARIZATION

A. Vergani

Name:

Name:

Var.:

Emiss.:01

Ed.:

Ed.: 05-03

Date:


12-05-2003Dept.:

Exec.:

CMO-GS-NI-SE

Ø 75÷115mm POLE(recommended Ø 115mm)

NB1 = FOR THE P/N see Sheets 4...6FOR THE WAVEGUIDE PRESSURIZATION see Sheet 3

SOLUTION WITH ELLIPTICAL WAVEGUIDENOT INTEGRATED SYSTEM

Sheet 1/9

P

U





SRAL XD

SOLUTION WITH ELLIPTICAL WAVEGUIDE

PU

P

U

U

P

P

U

U

P

Name:Var.:Ed.:

WHEN THE ODUs MUST BE INSTALLED INSIDE A SHELTER OR EQUIPMENT ROOM, THE WAVEGUIDE MUST BECONNECTED TO GROUND BEFORE ENTERING INSIDE THE SHELTER OR EQUIPMENT ROOM.

1+0 VERTICAL FRAMEor

SUPPORTING FRAME WITH PASSING HOLEUSE ONLY THE SCREWS SUPPLIEDWITH THE WAVEGUIDE CONNECTOR

or

USE ONLY THE SCREWS SUPPLIEDWITH THE SUPPORTING FRAME

SUPPORTING FRAME WITH BLIND HOLE

1+1 SUPPORTING FRAME

"E" BEND 90°(NB1)

g

06-0707 A. Vergani

U



A. Vergani

Name:

Name:

Var.:

Emiss.:01

Ed.:

Ed.: 05-03

Date:


12-05-2003Dept.:

Exec.:

CMO-GS-NI-SE

Sheet 2



SRAL XD


Name:Var.:Ed.:

NOT INTEGRATED SYSTEMSOLUTION WITH ELLIPTICAL WAVE GUIDE

CONNECTION WITH ANTENNAS Ø >1,8m FOR 7 - 13 GHz

A. Vergani06-0707

(a)d

e f (a)

ELLIPTICAL WAVEGUIDE1

(a)

PU U

P

P UU

P

U

P

"HORIZONTAL" POLARIZATION"VERTICAL" POLARIZATION

a) = FOR THE P/N OF THESE ACCESSORIES SEE SHEETS 4...7FOR THE WAVEGUIDE PRESSURIZATION SEE SHEET 3



P

U

TWIST(a)

C

(a)STRAIGHT SECTION m STRAIGHT SECTION

(a)m

Ø 115mm POLE

WAVEGUIDE SUPPORTUNIVERSAL CLAMPand RUBBER BUSH

(13 GHz)

(7 GHz)

PDR 120

PDR 70



A. Vergani

Name:

Name:

Var.:

Emiss.:01

Ed.:

Ed.: 05-03

Date:


12-05-2003Dept.:

Exec.:

CMO-GS-NI-SE

Sheet 3



SRAL XD


Name:Var.:Ed.:

633-051/68EXTERNAL DEHYDRATOR

DEHYDRATOR PIPE

NOT INTEGRATED SYSTEMSOLUTION WITH ELLIPTICAL WAVE GUIDE

PRESSURIZATION WITH EXTERNAL DEHYDRATOR

WAVEGUIDE CONNECTORODU SIDE

IT IS RECOMMENDED FOR WAVEGUIDE RUN OVER:NOTE

5m (7 GHz), 6m (8 GHz), 11m (13 GHz), 16m (15 GHz), 25m (18 GHz), 38m (23 GHz) and 45m (26-28-32-38 GHz)

(a)

(a)

a) = IS NOT INCLUDED IN THE INSTALLATION MATERIALS, IF REQUIRED MUST BE SEPARATELY PROVIDED

A. Vergani06-0707

90° GAS INLET (a)





IMC 0255BEDG

SRAL XD


NOT INTEGRATED SYSTEM SOLUTION WITH ELLIPTICAL WAVEGUIDE Sheet 4

NOT INTEGRATED SYSTEM SOLUTION WITH ELLIPTICAL WAVEGUIDE

P/N • 7 GHz

ELLIPTICAL WAVEGUIDE (31263-750) ITEM DESCRIPTION P/N Unit Q.ty

1a ELLIPTICAL WAVEGUIDE (EWP 64-71) 127-042/05 Mt. NOTE 1-3

1b ELLIPTICAL WAVEGUIDE (EWP 77-71W) 127-042/14 Mt. NOTE 1-4

2 ADAPTER FOR ANGULAR (10pz) 165-005/84 N° NOTE 1

3a WAVEGUIDE CLAMP (10pz) 165-005/69 N° NOTE 1-3

3b WAVEGUIDE CLAMP (10pz) 165-005/70 N° NOTE 1-4

CONNECTORS AND ACCESSORIES (31263-778SR) ITEM DESCRIPTION P/N Unit Q.ty

a1 WAVEGUIDE CONNECTOR EWP 64-71 (PDR 84) 504-237/99 N° 2 NOTE 3

a2 WAVEGUIDE CONNECTOR EWP 77-71W (PDR 84) 504-237/87 N° 2 NOTE 4

d WAVEGUIDE SUPPORT 332-055/21 N° 3

e UNIVERSAL CLAMP(∅ 62) 165-005/19 N° 3

f1 RUBBER BUSH (∅ 62) 332-202/90 N° 3 NOTE 3

f2 RUBBER BUSH (∅ 62) 332-202/87 N° 2 NOTE 4

g 90° “E” BEND (UDR-UDR 84) 504-393/36 N° 1 NOTE 5

i TWIST (UDR-PDR 84) 504-631/21 N° 1 NOTE 2

m TRANSITION 504-216/21 N° 1 NOTE 6

• 8 GHz ELLIPTICAL WAVEGUIDE (31263-758)

ITEM DESCRIPTION P/N Unit Q.ty

1 ELLIPTICAL WAVEGUIDE (EWP 77-77) 127-042/06 Mt. NOTE 1


3 WAVEGUIDE CLAMP (10pz) 165-005/70 N° NOTE 1

CONNECTORS AND ACCESSORIES (31263-779SR) ITEM DESCRIPTION P/N Unit Q.ty

a WAVEGUIDE CONNECTOR (PDR 84) 504-237/87 N° 2


e UNIVERSAL CLAMP(∅62) 165-005/19 N° 3

f RUBBER BUSH (∅ 62) 332-202/87 N° 3

g 90° “E” BEND (UDR-UDR 84) 504-393/36 N° 1 NOTE 5

i TWIST (UDR-PDR 84) 504-631/21 N° 1 NOTE 2

NOTE 1 = QUANTITY TO BE DEFINED AS PER PLANT REQUIREMENTS NOTE 2 = OPTIONAL, USE FOR HORIZONTAL POLARIZATION ONLY NOTE 3 = FOR 7.1-7.4 GHz and 7.4-7.7 GHz CHANNELINGS NOTE 4 = FOR 7.4-7.9 GHz CHANNELING NOTE 5 = ORDER FOR Ø <1,2 m ANTENNAS NOTE 6 = ORDER FOR Ø >1,8 m ANTENNAS





IMC 0255BEDG

SRAL XD




P/N • 13 GHz

ELLIPTICAL WAVE GUIDE (31263-766)


1 ELLIPTICAL WAVE GUIDE (EWP 127) 127-042/08 Mt. NOTE 1


3 WAVE GUIDE CLAMP (10pz) 165-005/72 N° NOTE 1

CONNECTORS AND ACCESSORIES (31263-781SR)


a WAVE GUIDE CONNECTOR (PBR 120) 504-237/97 N° 2

d WAVE GUIDE SUPPORT 332-055/21 N° 3


f RUBBER BUSH (∅ 38) 332-202/83 N° 3

g 90° “E” BEND (UBR-UBR120) 504-446/68K N° 1 NOTE 5

i TWIST (UBR-PBR 120) 504-656/52K N° 1 NOTE 2

m TRANSITION 504-216/23 N° 1 NOTE 6





3 WAVE GUIDE CLAMP (10pz) 165-005/72 N° NOTE 1



a WAVE GUIDE CONNECTOR (PBR 140) 504-237/96 N° 2



f RUBBER BUSH (∅ 38) 332-202/82 N° 3

g 90° “E” BEND (UBR-UBR140) 504-446/69K N° 1


NOTE 1 = QUANTITY TO BE DEFINED AS PER PLANT REQUIREMENTS NOTE 2 = OPTIONAL, USE FOR HORIZONTAL POLARIZATION ONLY NOTE 5 = ORDER FOR Ø <1,2 m ANTENNAS NOTE 6 = ORDER FOR Ø >1,8 m ANTENNAS





IMC 0255BEDG

SRAL XD




P/N



1 ELLIPTICAL WAVEGUIDE (EWP 180) 127-042/10 Mt. NOTE 1





a WAVEGUIDE CONNECTOR (PBR 220) 504-237/94 N° 2



f RUBBER BUSH (∅ 38) 332-202/84 N° 3

g 90° “E” BEND (UBR-UBR 220) 504-446/70K N° 1

i TWIST (UBR-PBR 220) 504-656/54K N° 1 NOTA 2











f RUBBER BUSH (∅ 38) 332-202/85 N° 3

g 90° “E” BEND (UBR-UBR 220) 504-446/70K N° 1


NOTE 1 = QUANTITY TO BE DEFINED AS PER PLANT REQUIREMENTS NOTE 2 = OPTIONAL, USE FOR HORIZONTAL POLARIZATION ONLY





IMC 0255BEDG

SRAL XD




P/N











f RUBBER BUSH (∅ 38) 332-202/89 N° 3

g 90° “E” BEND (UBR-UBR 220) 504-446/70K N° 1





e UNIVERSAL CLAMP(∅ 38) 165-005/17 N° NOTE 1

f RUBBER BUSH FOR E 300 332-202/60 N° NOTE 1



a E 300 WAVEGUIDE CONNECTOR (PBR 320) 504-237/17 N° 2

a1 SILICONE SEALING FOR W/G CONNECTOR 104-104/04 N° 1


g 90° “E” BEND (UBR-UBR 320) 504-446/71K N° 1





g UNIVERSAL CLAMP(∅ 38) 165-005/17 N° NOTE 1

h RUBBER BUSH FOR E 300 332-202/60 N° NOTE 1



b E 300 WAVEGUIDE CONNECTOR (PBR 320) 504-237/17 N° 2


e WAVEGUIDE SUPPORT 332-055/21 N° 3

h 90° “E” BEND (UBR-UBR 320) 504-446/71K N° 1


NOTE 1 = QUANTITY TO BE DEFINED AS PER PLANT REQUIREMENTS NOTE 2 = OPTIONAL, USE FOR HORIZONTAL POLARIZATION ONLY





IMC 0255BEDG

SRAL XD




P/N

• 38 GHz ELLIPTICAL WAVE GUIDE (31262-772)

ITEM DESCRIPTION P/N Unit Q. ty


e UNIVERSAL CLAMP (ø 38) 165-005/17 N° NOTE 1

f RUBBER BUSH FOR E 380 332-202/93 N° NOTE 1


ITEM DESCRIPTION P/N Unit Q. ty

a E 380 WAVE GUIDE CONNECTOR (PBR 320) 504-237/09 N° 2



g 90° E BEND (UBR-UBR 320) 504-446/71K N° 1


NOTE 1 = QUANTITY TO BE DEFINE ACCORDING TO THE INSTALLATION REQUIREMENTS NOTE 2 = OPTION, TO BE USED FOR THE HORIZONTAL POLARIZATION ONLY





IMC 0255BEDG

SRAL XD



NOT INTEGRATED SYSTEM

SOLUTION WITH ELLIPTICAL WAVEGUIDE REVISION LIST

Revisions Revisions Sheet 01 02 03 04 05 06 07 08 09 10 Sheet 01 02 03 04 05 06 07 08 09 10 01 ¯ ¯ ¯ ¯ ¯ ¯ ¯ - 02 ¯ ¯ ¯ ¯ - 03 ¯ ¯ ¯ ¯ ¯ ¯ - 04 ¯ ¯ ¯ ¯ - 05 ¯ ¯ ¯ ¯ - 06 ¯ ¯ ¯ ¯ - 07 ¯ ¯ ¯ ¯ ¯ - 08 ¯ ¯ ¯ - 09 ¯ ¯ ¯ ¯ - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -




INSTALLATION INFORMATION for OUTDOOR ASSEMBLY

SRAL XD

CMO-GS-NI-SE

A. Vergani

Dept.:

Exec.:

Date:

Check:

12-05-2003

M. Brambilla

IMC 0256BEDG

Sheet 1/8

Name:

Name:

Var.:

Emiss.:

Ed.:


(See Sheets 2-3) OUTDOOR ASSEMBLY

OUTDOOR ASSEMBLYASSEMBLY ON SUPPORT FRAME

A. Vergani06-0708





SRAL XD

CMO-GS-NI-SE

A.Vergani

Dept.:

Exec.:

Date:

Check:

12-05-2003

M.Brambilla

IMC 0256BEDG

Sheet 2

Name:

Name:

Var.:

Emiss.:

Ed.:

Ed.: 01 05-03 A.Vergani

OUTDOOR ASSEMBLYNORMAL DENSITY

(DOWN VIEW)

WEIGHT OF THE OUTDOOR ASSEMBLY = 4.3 Kg

(See IMC 0257BEDG)GROUNDING SCREW

(SIDE VIEW)

(FRONT VIEW)

FOR FEEDER FLANGESee Sheet 4

RX FIELD MEASURE

(See Sheet 7)CONNECTOR IN/OUT CABLE

(See IMC 0257BEDG)CONNECTOR

267

238

281

123

and HIGH DENSITY ENHANCED

08 06-07 A. Vergani





SRAL XD

CMO-GS-NI-SE

A.Vergani

Dept.:

Exec.:

Date:

Check:

12-05-2003

M.Brambilla

IMC 0256BEDG

Sheet 3

Name:

Name:

Var.:

Emiss.:

Ed.:

Ed.: 01 05-03 A.Vergani

OUTDOOR ASSEMBLYNORMAL DENSITY 2

(TO USE FOR THE TRANSPORT)HANDLE

08 06-07 A.Vergani

WEIGHT OF THE OUTDOOR ASSEMBLY = 3.250 Kg

CONNECTORRX FIELD MEASURE

GROUNDING SCREW

CONNECTORIN/OUT CABLE

23527

5

(FRONT VIEW)

(DOWN VIEW)

235262

(REAR VIEW)

102

(See IMC 0257BEDG) FOR FEEDER FLANGESee Sheet 4

(See IMC 0257BEDG) (See Sheet 7)





IMC 0256BEDG

SRAL XD


INSTALLATION INFORMATION for OUTDOOR ASSEMBLY Sheet 4

OUTDOOR ASSEMBLY SHIFTER, P/N and FLANGE


FREQUENCY SHIFTER

(MHz) NORMAL DENSITY

HIGH DENSITY ENHANCED (a)

NORMAL DENSITY 2

FEEDER FLANGE

7 (7.1 ÷ 7.9)

148.5 / 154 / 161 168 / 245 / 196 732-251/07 732-241/07E - UDR 84

8 (7.7 ÷ 8.5)

119 / 126 266 / 311.25 732-251/08 732-241/08E - UDR 84

13 (12.75 ÷ 13.25) 266 732-251/13 732-241/13E - UBR 120

15 (14.5 ÷ 15.35)

315 / 322 / 336 420 / 490 644 / 728

732-251/15 732-241/15E 732-251/15E UBR 140

18 (17.7 ÷ 19.7)

120 / 340 / 1008 1010 / 1560 732-251/18 732-241/18E 732-251/18E UBR 220

23 (21.2 ÷ 23.6) 1008 / 1200 / 1232 732-251/23 732-241/23E 732-251/23E UBR 220

26 (24.5 ÷ 26.5) 1008 732-251/26 732-241/26E - UBR 220

28 (27.5 ÷ 29.5) 1008 732-251/28 732-241/28E - UBR 320

32 (31.8 – 33.4) 812 - 732-241/32E - UBR 320

38 (37.0 ÷ 39.5) 1260 732-251/38 732-241/38E, F (b) 732-251/38E UBR 320

Temperature Range : -33° to +55° C (a) = The IDU 32 x 2Mbit/s needs ODU type HDe or ND2 (b) = 732-241/38E: Standard; 732-241/38F: Short Haul (including a 15 dB fixed attenuator in trasmission).





SRAL XD

CMO-GS-NI-SE

A. Vergani

Dept.:

Exec.:

Date:

Check:

12-05-2003

M. Brambilla

IMC 0256BEDG

Sheet 5

Name:

Name:

Var.:

Emiss.:

Ed.:


OUTDOOR ASSEMBLY"VERTICAL" POLARIZATION APPLICATION

NOTE = FOR "HORIZONTAL" POLARISED APPLICATION, THE IN/OUT CABLE CONNECTOR IS ON RIGHT HAND SIDE

"HORIZONTAL" POLARIZATION APPLICATIONOUTDOOR ASSEMBLY

NOTE = FOR "VERTICAL" POLARISED APPLICATION, THE IN/OUT CABLE CONNECTOR IS AT BOTTOM

(REAR VIEW)


IN/OUT CABLECONNECTOR

GROUND

NORMAL DENSITY

NORMAL DENSITY

RX FIELD MEASURE

(REAR VIEW)

CONNECTOR

CONNECTORIN/OUT CABLE

GROUND



08 06-07 A. Vergani





SRAL XD

CMO-GS-NI-SE

A. Vergani

Dept.:

Exec.:

Date:

Check:

12-05-2003

M. Brambilla

IMC 0256BEDG

Sheet 6

Name:

Name:

Var.:

Emiss.:

Ed.:


08 06-07 A. Vergani


NORMAL DENSITY 2

NORMAL DENSITY 2

NOTE = FOR "VERTICAL" POLARISED APPLICATION, THE IN/OUT CABLE CONNECTOR IS AT BOTTOM

OUTDOOR ASSEMBLY"HORIZONTAL" POLARIZATION APPLICATION

NOTE = FOR "HORIZONTAL" POLARISED APPLICATION, THE IN/OUT CABLE CONNECTOR IS ON RIGHT HAND SIDE

"VERTICAL" POLARIZATION APPLICATION

OUTDOOR ASSEMBLY

(REAR VIEW)


(REAR VIEW)



GROUND

GROUND





SRAL XD

CMO-GS-NI-SE

A. Vergani

Dept.:

Exec.:

Date:

Check:

12-05-2003

M. Brambilla

IMC 0256BEDG

Sheet 7

Name:

Name:

Var.:

Emiss.:

Ed.:


OUTDOOR ASSEMBLY"RX FIELD MEASURE"

a) = THIS "RX FIELD MEASURE" CONNECTOR IS THE TEST POINT FOR THE CONNECTION OF A VOLT METER DURING THEANTENNA ALIGNMENT PROCEDURE

RX FIELD MEASURECONNECTOR

"BNC" SOCKET (a)

CONNECTOR

08 06-07 A. Vergani





IMC 0256BEDG

SRAL XD


INSTALLATION INFORMATION for OUTDOOR ASSEMBLY Sheet 8

OUTDOOR ASSEMBLY

REVISION LIST


Sheet 01 02 03 04 05 06 07 08 09 10

01 ¯ ¯ ¯ ¯ ¯ ¯ ¯ ¯ - 02 ¯ ¯ ¯ - 03 ¯ ¯ ¯ ¯ - 04 ¯ ¯ ¯ ¯ ¯ ¯ ¯ ¯ - 05 ¯ ¯ ¯ - 06 ¯ ¯ ¯ ¯ - 07 ¯ ¯ - 08 ¯ ¯ ¯ ¯ ¯ ¯ ¯ ¯ - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -



LOW CAPACITY DIGITAL RADIO SYSTEMINSTALLATION INFORMATION for BRAIDED COAXIAL CABLE

SRAL XD

CMO-GS-NI-SE

A. Vergani

Dept.:

Exec.:

Date:

Check:

12-05-2003

M. Brambilla

IMC 0257BEDG

Sheet 1/10

Name:

Name:

Var.:

Emiss.:

Ed.:


NOTE = THE MAX LENGHT OF ONE IDU/ODU CONNECTION IS 200 mt (140 mt FOR IDU 32xE1)

BRAIDED COAXIAL CABLETYPICAL CONNECTION

a) = For P/N see sheet 7

COAXIAL CONNECTOR(a)90° "N" type

COAXIAL CABLEIN/OUT BRAIDED

(a)

COAXIAL CONNECTOR(a)90° "SMA" type IDU ASSEMBLY

A. Vergani06-0708




SRAL XD

CMO-GS-NI-SE

A. Vergani

Dept.:

Exec.:

Date:

Check:

12-05-2003

M. Brambilla

IMC 0257BEDG

Sheet 2

Name:

Name:

Var.:

Emiss.:

Ed.:


BRAIDED COAXIAL CABLEGROUNDING CONNECTIONS, INTEGRATED SOLUTION

b) = FOR THE FIXING OF THE BRAIDED COAXIAL CABLE see Sheet 5c) = N°1 GROUNDING KIT IS A STANDARD SOLUTION FOR A BRAIDED COAXIAL CABLE TYPICAL PATH <50m,

d) = THIS CABLE IS SUPPLIED WITH THE INSTALLATION MATERIALS

(d)



GROUNDING SYSTEM

TO CONNECTTO THE STATION

GROUNDING POINTGENERAL

BRAIDED COAXIAL CABLE (a) (b)

(a)(b)

(a)(b)

INDOOR

GROUNDING KIT

1x16mm² PVC YE-GRGROUND CABLE

(103-037/50)

(c)(a)

e) = OPTIONAL ITEM, IF REQUIRED MUST BE SEPARATELY PROVIDED

BENDING RADIUSsee Sheet 8

a) = FOR P/N see Sheet 7

THE USE OF ADDITIONAL GROUNDING KITS HAS TO BE EVALUTED ACCORDING TO THE PATH TYPE

333-047/07GROUNDING PLATE(e)

A. Vergani06-0708

USE THE CABLE STRIPPING TOOL 236-100/89




SRAL XD

CMO-GS-NI-SE

A. Vergani

Dept.:

Exec.:

Date:

Check:

12-05-2003

M. Brambilla

IMC 0257BEDG

Sheet 3

Name:

Name:

Var.:

Emiss.:

Ed.:


BRAIDED COAXIAL CABLEGROUNDING CONNECTIONS, NOT INTEGRATED SOLUTION

c) = N°1 GROUNDING KITS ARE A STANDARD SOLUTION FOR A BRAIDED COAXIAL CABLE TYPICAL PATH <50m,



b) = FOR THE FIXING OF THE BRAIDED COAXIAL CABLE see Sheet 5

(f) = FOR THE FIXING OF THE GROUND PLATE see Sheet 4



USE THE CABLE STRIPPING TOOL 236-100/39

(e)

(a)



TO THE GROUNDINGSTATION SYSTEM

see Sheet 8BENDING RADIUS


GROUNDINGGENERAL

POINT

TO CONNECT

(a)(b)

(332-309/91)


GROUNDING PLATE

(103-037/50)

(a)(b)

(b)

(f)

INDOOR

(c)

GROUNDING PLATE

(a)

(d)

333-047/07(e)

GROUNDING KIT

08 06-07 A. Vergani




SRAL XD

CMO-GS-NI-SE

A. Vergani

Dept.:

Exec.:

Date:

Check:

12-05-2003

M. Brambilla

IMC 0257BEDG

Sheet 4

Name:

Name:

Var.:

Emiss.:

Ed.:


BRAIDED COAXIAL CABLEPOLE FIXING OF THE GROUNDING PLATE KIT

223-002/86

Ø79 ÷ 127

TIE

332-004/92

257-41/507GROUNDING PLATE

PLATE

50

32 25

SCREW

TERMINAL TUBE

PLAIN WASHER

SPRING WASHER

HEX NUT

GROUNDING CABLE1x16 mm² or 1x25 mm² YE-GR

(a)

(a)(a)

(a)

(a)

(a)

(a)

(a)

(b)

a) = THESE MATERIALS ARE INCLUDED IN 332-309/91b) = IF REQUIRERD MUST BE SEPARATELY PROVIDED

Ø16 mm² or Ø25 mm²

(332-309/91)

A. Vergani06-0708




SRAL XD

CMO-GS-NI-SE

A. Vergani

Dept.:

Exec.:

Date:

Check:

12-05-2003

M. Brambilla

IMC 0257BEDG

Sheet 5

Name:

Name:

Var.:

Emiss.:

Ed.:


BRAIDED COAXIAL CABLETYPICAL FIXING

b) = MATERIAL TO BE ADOPTED ACCORDING TO THE INSTALLATION REQUIREMENTS,IS NOT INCLUDED IN THE INSTALLATION MATERIALS, IF REQUIRED MUST BE SEPARATELY PROVIDED,REFER TO SHEET 6 FOR THE RECOMMENDED SPACING

a) = N° 5 EXTERNAL BLACK TIE, FOR THE FIXING OF THE CABLE RUNNING ON THE POLE, ARE INCLUDED IN THE INSTALLATION KIT

UNIVERSAL CABLE CLAMP (b)

for 4 3/10" Cables

3838

71

Max

22

for 2 3/10" Cables

52,5

D = 74 ÷ 140 mm 223-009/27 (a)

D

332-202/95 332-202/96


CABLE TIEUNIVERSAL

D = 26 ÷ 62 mm 332-004/93 10 pieces (b)

(223-009/27)(a)

CABLE TIE(223-009/25)(b)

or

CABLE CLAMP(332-202/95)(332-202/96)

Max

22

(b)

CABLE TIE (a) (b)

INDOOR

(223-009/25)

A. Vergani06-0708

236-100/50USE THE STRAP PLIER

WARNING





IMC 0257BEDG

SRAL XD


INSTALLATION INFORMATION for BRAIDED COAXIAL CABLE Sheet 6

BRAIDED COAXIAL CABLE FIXING RULES

RECOMMENDED CLAMP SPACING FOR BRAIDED COAXIAL CABLE

Clamp spacing recommendation is based on the guidelines stated in EIA Standard RS-222 (Structural Standards for Steel Antenna Towers and Antenna Supporting Structures) and BSI CP3 (Code of Basic Data for the Design of Buildings, Wind Loading).

Geographical location, as well as height of tower/must, to which the clamps are attached, may have a significant impact on installation conditions.

Therefore, unless otherwise specified, the assumptions made to define the maximum clamp spacing are the following:

• Tower height 45m • 1/2” radial ice • Clamps properly installed and tightened

Based on the above conditions, the recommended MAXIMUM CLAMP SPACING for BRAIDED COAXIAL CABLE type CNT 300FR (Andrew) and ICN48 (INTERCOND) is 0,5m





IMC 0257BEDG

SRAL XD


INSTALLATION INFORMATION for BRAIDED COAXIAL CABLE

Sheet 7

BRAIDED COAXIAL CABLE COAXIAL CABLE and CONNECTION KIT

ANDREW SET (a)

P / N DESCRIPTION UNIT Q.TY

104-009/50 314-331/88 (b)

CNT300 - 50 Ohm BRAIDED COAXIAL CABLE Mt. (b)

597-525/59A 597-525/59 (b)

BRAIDED COAX CABLE ACCESSORIES Nr. (c)

421-025/30 90° COAX SMA-PLUG 1

421-008/35 90° COAX N-PLUG 1

333-031/21 GROUNDING KIT 1

FOR THE ASSEMBLING INSTRUCTIONS SEE THE INFORMATION PROVIDED WITH THE CONNECTOR

OR

INTERCOND SET (a)


104-009/51 314-331/88 (b)

INC48 - 50 Ohm BRAIDED COAXIAL CABLE Mt. (c)

597-525/59B 597-525/59 (b)

BRAIDED COAXIAL CABLE ACCESSORIES Nr. (d)

421-025/31 90° COAX SMA-PLUG 1

421-008/36 90° COAX N-PLUG 1



a) = The ANDREW and INTERCOND material sets are alternative to each other

b) = Commercial reference code

c) = The max length of one IDU/ODU connection is 200 mt (140 mt for IDU 32xE1)

d) = Q.ty 1 for each IDU/ODU connection





IMC 0257BEDG

SRAL XD




Characteristics 1. Construction Characteristics ANDREW INTERCOND Inner Conductor Diameter (mm) 1.78 1.78 Dielectric Diameter (mm) 4.83 4.90 Outer Conductor Diameter (mm) 4.98 6.00 Standard Jacket Diameter (mm) 7.62 7.60 2. Mechanical Characteristics ANDREW INTERCOND Weight (kg/m) 0.08 0.095 Min. Bending Radius single bend (mm) > 22.2 > 25 Tensile Strength (kg) 120 50 Bending Moment (N • m) 0.52 - Crash Strength (kg/mm) 0.54 - Max. Standard Hanger Spacing (m) 1 - 3. Range of Temperature ANDREW INTERCOND Recommended Temperature for Installation (°C) - 40 / + 85 - 40 / + 85 Recommended Storage for Installation (°C) - 70 / + 85 - 40 / + 85 Operating Temperature (°C) - 40 / + 85 - 40 / + 85 4. Electrical Characteristics ANDREW INTERCOND Characteristics Impedance (Ω) 50 50 Relative Propagation Velocity (%) 85 - Capacitance (pF/m) 79.10 - Maximun Operating Frequency (Mhz) 2450 - Peak Power Rating (kW) 10 10 DC Resistance : Inner Conductor (Ω/km) 6.9 7.20 DC Resistance : Outer Conductor (Ω/km) 7.25 5.32 DC Breakdown (V) 2000 - Inductance (µH/m) 0.20 0.20 (Continue)





IMC 0257BEDG

SRAL XD



5. Attenuation, (dB/100m) Standard conditions : VSWR 1.0 ; ambient temperature 24°C

ANDREW INTERCOND 30 MHz 3.50 - 50 MHz 4.50 -

150 MHz 7.80 7.80 450 MHz 13.70 13.70 900 MHz 19.7 -

1500 MHz 25.70 - 1700 MHz - 27.50 2000 MHz 30.0 - 2200 MHz - 31.30 2300 MHz 33.9 23.1

6. Average Power Rating, kW Standard conditions : VSWR 1.0 ; ambient temperature 40°C ; inner conductor temperature 100°C ;

ANDREW INTERCOND 30 MHz 2.10 - 50 MHz 1.60 -

150 MHz 0.92 - 450 MHz 0.52 - 900 MHz 0.36 -

1500 MHz 0.28 - 2000 MHz 0.24 - 2300 MHz 0.22 -





IMC 0257BEDG

SRAL XD




REVISION LIST


Sheet 01 02 03 04 05 06 07 08 09 10

01 ¯ ¯ ¯ ¯ ¯ ¯ ¯ ¯ - 02 ¯ ¯ ¯ ¯ ¯ ¯ - 03 ¯ ¯ ¯ ¯ ¯ ¯ ¯ - 04 ¯ ¯ ¯ - 05 ¯ ¯ ¯ ¯ ¯ ¯ - 06 ¯ ¯ ¯ - 07 ¯ ¯ ¯ ¯ ¯ ¯ - 08 ¯ ¯ ¯ - 09 ¯ ¯ ¯ - 10 ¯ ¯ ¯ ¯ ¯ ¯ ¯ ¯ - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -



TYPICAL CONNECTION

1/4" COAXIAL CABLE

LOW CAPACITY DIGITAL RADIO SYSTEMSRAL XD

CMO-GS-NI-SE

A. Vergani

Dept.:

Exec.:

Date:

Check:

12-05-2003

M. Brambilla

IMC 0258BEDG

Sheet 1/12

Name:

Name:

Var.:

Emiss.:

Ed.:


NOTE = The max lenght of one IDU/ODU connection is 300 mt (220 mt for IDU 32xE1)

1/4" IN/OUTCOAXIAL CABLE

INSTALLATION INFORMATION for 1/4" COAXIAL CABLE

IDU ASSEMBLY

A. Vergani06-0708



CONNECTION ON ODU SIDE

1/4" COAXIAL CABLE


CMO-GS-NI-SE

A. Vergani

Dept.:

Exec.:

Date:

Check:

12-05-2003

M. Brambilla

IMC 0258BEDG

Sheet 2

Name:

Name:

Var.:

Emiss.:

Ed.:



(a)1/4" COAXIAL CABLE

a) = FOR THE P/N OF THESE ACCESSORIES see Sheet 9

90° COAX N-PLUG(a)

(FRONT VIEW)

SECTIONTO IDU

08 06-07 A. Vergani



GROUNDING CONNECTIONS, INTEGRATED SOLUTION1/4" COAXIAL CABLE


CMO-GS-NI-SE

A. Vergani

Dept.:

Exec.:

Date:

Check:

12-05-2003

M. Brambilla

IMC 0258BEDG

Sheet 3

Name:

Name:

Var.:

Emiss.:

Ed.:



b) = FOR THE FIXING OF THE 1/4" COAXIAL CABLE see Sheet 6c) = N°1 GROUNDING KIT IS A STANDARD SOLUTION FOR A 1/4" COAXIAL CABLE TYPICAL PATH <50m,


(d)

1/4" COAXIAL CABLE

1/4" COAXIAL CABLE

GROUNDING SYSTEM

TO CONNECTTO THE STATION

(a)(b)

(a)(b)

INDOOR

GROUNDING KIT


(103-037/50)

(c)(a)


BENDING RADIUSsee Sheet 10



333-047/07GROUNDING PLATE(e)

08 06-07 A. Vergani

1/4" COAXIAL CABLE

GENERAL GROUNDING POINT

(a) (b)



GROUNDING CONNECTIONS, NOT INTEGRATED SOLUTION1/4" COAXIAL CABLE


CMO-GS-NI-SE

A. Vergani

Dept.:

Exec.:

Date:

Check:

12-05-2003

M. Brambilla

IMC 0258BEDG

Sheet 4

Name:

Name:

Var.:

Emiss.:

Ed.:



1/4" COAXIAL CABLE

1/4" COAXIAL CABLE

b) = FOR THE FIXING OF THE 1/4" COAXIAL CABLE see Sheet 6

THE USE OF ADDITIONAL GROUNDING KITS HAS TO BE EVALUTED ACCORDING TO THE PATH TYPEd) = THIS CABLE IS SUPPLIED WITH THE INSTALLATION MATERIALS

c) = N°1 GROUNDING KITS ARE A STANDARD SOLUTION FOR A 1/4" COAXIAL CABLE TYPICAL PATH <50m,


TO THE GROUNDINGSTATION SYSTEM

BENDING RADIUS

TO CONNECT

see Sheet 10

1/4" COAXIAL CABLE

(b) (a)

(b)(a)

(b)(a)

INDOOR


(a)GROUNDING KIT

(e)

(c)

e) = OPTIONAL ITEM, IF REQUIRED MUST BE SEPARATELY PROVIDEDf) = FOR THE FIXING OF THE GROUND PLATE see Sheet 5

A. Vergani06-0708


(e)

GROUNDINGPOINT

GENERAL

GROUNDING PLATE(332-309/91)

(103-037/50)

(f)

(d)



1/4" COAXIAL CABLE


CMO-GS-NI-SE

A. Vergani

Dept.:

Exec.:

Date:

Check:

12-05-2003

M. Brambilla

IMC 0258BEDG

Sheet 5

Name:

Name:

Var.:

Emiss.:

Ed.:



POLE FIXING OF THE GROUNDING PLATE KIT

223-002/86

Ø79 ÷ 127

TIE

332-004/92


PLATE

50

32 25

SCREW

TERMINAL TUBE

PLAIN WASHER

SPRING WASHER

HEX NUT

GROUNDING CABLE1x16 mm² or 1x25 mm² YE-GR

(a)

(a)(a)

(a)

(a)

(a)

(a)

(a)

(b)

a) = THESE MATERIALS ARE INCLUDED IN 332-309/91b) = IF REQUIRED MUST BE SEPARATELY PROVIDED

Ø16 mm² or Ø25 mm²

(332-309/91)

08 06-07 A. Vergani



1/4" COAXIAL CABLE


CMO-GS-NI-SE

A. Vergani

Dept.:

Exec.:

Date:

Check:

12-05-2003

M. Brambilla

IMC 0258BEDG

Sheet 6

Name:

Name:

Var.:

Emiss.:

Ed.:



TYPICAL FIXING

b) = IS NOT INCLUDED IN THE INSTALLATION MATERIALS IF REQUIRED MUST BE SEPARATELY PROVIDEDREFER TO SHEET 7 FOR THE RECOMMENDED SPACING

a) = N° 5 EXTERNAL BLACK TIE, FOR THE FIXING OF THE CABLE RUNNING ON THE POLE, ARE INCLUDED IN THE INSTALLATION KIT

UNIVERSAL CABLE CLAMP (b)

for 4 1/4" Cables

3838

71

Max

22

for 2 1/4" Cables

52,5

D = 74 ÷ 140 mm 223-009/27

D

332-202/65 332-202/66

1/4" COAXIAL CABLE

CABLE TIEUNIVERSAL

(223-009/27)(a)

CABLE CLAMP(332-202/65)(332-202/66)

Max

22

(b)

CABLE TIE (a)

INDOOR

c) = USE ONLY THE CLAMPS FOR FIXING THE 1/4" COAXIAL CABLE ON THE CABLE LADDER

(c)

06-0708 A. Vergani





IMC 0258BEDG

SRAL XD


INSTALLATION INFORMATION for 1/4” COAXIAL CABLE Sheet 7

1/4” COAXIAL CABLE FIXING RULES

RECOMMENDED CLAMP SPACING FOR 1/4” COAXIAL CABLE

Clamp spacing recommendation is based on the guidelines stated in EIA Standard RS-222 (Structural Standards for Steel Antenna Towers and Antenna Supporting Structures) and BSI CP3 (Code of Basic Data for the Design of Buildings, Wind Loading).

Geographical location, as well as height of tower/must, to which the clamps are attached, may have a significant impact on installation conditions.

Therefore, unless otherwise specified, the assumptions made to define the maximum clamp spacing are the following:

• Tower height 45m • 1/2” radial ice • Clamps properly installed and tightened

Based on the above conditions, the recommended MAXIMUM CLAMP SPACING for 1/4” COAXIAL CABLE type LDF1RN-50 (Andrew) is: 0,8m (Wind Load 200 Km/h) or 0,5m (Wind Load 240 Km/h).



1/4" COAXIAL CABLE


CMO-GS-NI-SE

A. Vergani

Dept.:

Exec.:

Date:

Check:

12-05-2003

M. Brambilla

IMC 0258BEDG

Sheet 8

Name:

Name:

Var.:

Emiss.:

Ed.:



CONNECTION ON IDU SIDE

TOIDU ASSEMBLY

(314-327/91)

(232-124/20)FIXING BRACKETCOAXIAL CABLE

"OSM/N" COAXIAL TAIL(L.=1 Mt.)

COAXIAL N-PLUG (a)

a) = FOR THE P/N see Sheet 9

1/4" COAXIAL CABLE(a)ODU SECTION

TO

THE FIGURE SHOWS AN EQUIPMENT WITH 2 BASE BAND; IN CASE OF ONE BASE BAND ONLY ONE IN/OUT CONNECTION IS PRESENT

STRAIGHT "N" type

(314-304/51)YE-GR PVC 1x16 mm²

GROUND CABLE

IDU ASSEMBLY

A. Vergani06-0708

b) = THESE MATERIALS ARE INCLUDED IN THE KIT 332-011/35 SUPPLIED WITH THE EQUIPMENTc) = THIS MATERIAL IS SUPPLIED WITH THE EQUIPMENT

(b)

(b)

(c)

MINIDU Plug-In / Single Board

1/4" COAXIAL(a)

ODU SECTIONTO

CABLE

(314-327/91)(c)

IDU ASSEMBLYTO

BUSH 6x3.5

SCREW 6x16

CAGE NUT M6

TO GROUNDING BARN3 ETSI/19" RACK

(b)

(b)

(b)"OSM/N" COAXIAL TAIL

(L.=1 Mt.)

M4 NUT + 4x8 SCREW(b)





IMC 0258BEDG

SRAL XD



1/4” COAXIAL CABLE COAXIAL CABLE and CONNECTION KIT

ANDREW SET


104-009/42 314-327/79 (a)

1/4” LDF1RN - 50 Ω COAXIAL CABLE Mt. (b)

597-523/94A 597-523/94 (a)

1/4” COAX CABLE ACCESSORIES Nr. (c)

421-008/88 COAX N-PLUG 1

421-008/84 90° COAX N-PLUG 1



a) = Commercial reference

b) = The length of one IDU/ODU connection is 300 mt Max (220 mt for IDU 32xE1)

c) = Q.ty 1 for each IDU/ODU connection





IMC 0258BEDG

SRAL XD



1/4” COAXIAL CABLE

Characteristics 1. Construction Characteristics

ANDREW Inner Conductor Diameter (mm) 2.6 Dielectric Diameter (mm) 6.7 Outer Conductor Diameter (mm) 7.7 Standard Jacket Diameter (mm) 9

2. Mechanical Characteristics

ANDREW Weight (kg/m) 0.09 Min. Bending Radius single bend (mm) 38 Min. Bending Radius repeated bends (mm) 76 Number of Bends Min. (typical) 15 (30) Tensile Strength (kg) 91 Bending Moment (N • m) 1.33 Max. Tensile Force (N) - Crush Strength (kg/mm) 1.4 Max. Standard Hanger Spacing (m) 0.5

3. Range of Temperature

ANDREW Recommended Temperature for Installation (°C) - 25 / + 60 Recommended Storage for Installation (°C) - 30 / + 80 Operating Temperature (°C) - 30 / + 80

4. Electrical Characteristics

ANDREW Characteristics Impedance (Ω) 50 Relative Propagation Velocity (%) 87 Capacitance (pF/m) 76.8 Maximun Operating Frequency (Mhz) 15800 Cut-off Frequency (Mhz) - Peak RF Voltage Rating (kV) 1.1 Peak Power Rating (kW) 12.1 DC Resistance : Inner Conductor (Ω/km) 5.15 DC Resistance : Outer Conductor (Ω/km) 3.33 DC Breakdown (V) 2200 Inductance (µH/m) 0.19

(Continue)





IMC 0258BEDG

SRAL XD



5. Attenuation, (dB/100m) Standard conditions : VSWR 1.0 ; ambient temperature 24°C

ANDREW 10 MHz - 30 MHz 2.20

100 MHz 4.08 150 MHz 5.03 200 MHz - 300 MHz 7.22 450 MHz 8.94 600 MHz 10.42 824 MHz 12.36 894 MHz 12.92 900 MHz - 960 MHz 13.43

1000 MHz 13.73 1500 MHz 17.15 1700 MHz 18.38 1800 MHz - 2000 MHz 20.13 2300 MHz 21.77 3000 MHz - 4000 MHz 29.89 6000 MHz 37.94

10000 MHz 51.72 6. Average Power Rating, kW Standard conditions : VSWR 1.0 ; ambient temperature 40°C ; inner conductor temperature 100°C ;

ANDREW 10 MHz - 30 MHz 3.38 100 MHz 1.85 150 MHz 1.51 200 MHz - 300 MHz 1.07 450 MHz 0.871 600 MHz 0.756 824 MHz 0.644 894 MHz 0.618 900 MHz - 960 MHz 0.579

1000 MHz 0.585 1500 MHz 0.477 1700 MHz 0.448 1800 MHz - 2000 MHz 0.413 2300 MHz 0.385 3000 MHz - 4000 MHz 0.292 6000 MHz 0.239 10000 MHz 0.185





IMC 0258BEDG

SRAL XD



1/4” COAXIAL CABLE

REVISION LIST

Revisions Revisions Sheet 01 02 03 04 05 06 07 08 09 10 Sheet 01 02 03 04 05 06 07 08 09 10 01 ¯ ¯ ¯ ¯ ¯ ¯ ¯ ¯ - 02 ¯ ¯ ¯ - 03 ¯ ¯ ¯ ¯ ¯ - 04 ¯ ¯ ¯ ¯ ¯ ¯ - 05 ¯ ¯ - 06 ¯ ¯ ¯ ¯ ¯ - 07 ¯ ¯ - 08 ¯ ¯ ¯ ¯ ¯ - 09 ¯ ¯ ¯ ¯ ¯ ¯ - 10 ¯ ¯ ¯ - 11 ¯ ¯ ¯ - 12 ¯ ¯ ¯ ¯ ¯ ¯ ¯ ¯ - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -



RACK ASSEMBLY

INDOOR ASSEMBLY


CMO-GS-NI-SE

A. Vergani

Dept.:

Exec.:

Date

Check:

31-05-2006

M. Brambilla

IMC 0359BEDG

Sheet 1/20

Name:

Name:

Var.:


MAX 22 IDUs CAN BE EQUIPPED IN THE N3 ETSI RACKMAX 18 IDUs CAN BE EQUIPPED IN THE 19" RACK

SINGLE - BOARD 2

INDOOR ASSEMBLY732-102/71A,B,D

301-011/92 (301-021/02)19" (N3 ETSI) RACK

SINGLE - BOARD 2




GROUNDING CONNECTIONS

INDOOR ASSEMBLY

LOW CAPACITY DIGITAL RADIO SYSTEMSRAL XD Single - Board 2 IMC 0359BEDG

Sheet 2

SINGLE - BOARD 2

b) = THIS CABLE IS INCLUDED IN THE IDU CONNECTION KIT-Basic (597-525/16); see IMC 0361BEDGa) = THIS CABLE IS INCLUDED IN THE 19" (N3 ETSI) RACK

(6mm² L.= 400)GROUNDING CABLE

(b)

GROUNDING BAR

(314-303/56)

EARTHING SYSTEMSTATION

TO

YE-GR PVC 1x25mm²GROUNDING CABLE

(a)

(203-341/08D)M4x10 CYLINDRICAL HEAD SCREW

(c)

c) = THESE ACCESSORIES ARE INCLUDING IN THE IDU SUBRACK

A. Vergani

CMO-GS-NI-SE

Exec.:

Dept.:

Check:

Date 31-05-2006

M. Brambilla

Name:

Name:

Var.:


SPACING ROD(211-483/79)

(c)




MOUNTING BRACKET

INDOOR ASSEMBLY


Sheet 3

SINGLE-BOARD 2

a) = THESE ACCESSORIES ARE CONTAINED IN THE FIXING KIT (332-310/65)

BRACKET for 19"(224-174/77)

(a)

FLAT HEAD SCREW 4x8(201-402/07D) (a)

for19" RACK

A. Vergani

CMO-GS-NI-SE

Exec.:

Dept.:

Check:

Date

M. Brambilla

31-05-2006

Name:

Name:

Emiss.:

Var.:





MOUNTING BRACKET

INDOOR ASSEMBLY


Sheet 4

SINGLE-BOARD 2

a) = THESE ACCESSORIES ARE CONTAINED IN THE FIXING KIT (332-310/65)

forN3 ETSI RACK

(224-174/76)BRACKET for N3 ETSI

FLAT HEAD SCREW 4x8 (a)

(a)

(201-402/07D)

A. Vergani

CMO-GS-NI-SE

Exec.:

Dept.:

Check:

Date 31-05-2006

M. Brambilla Name:

Name:Var.:





EQUIPMENTINDOOR ASSEMBLY


Sheet 5

SINGLE-BOARD 2

1+0

ENVIRONMENTAL TEMPERATURE RANGE: -5° to +55° C WEIGHT OF THE INDOOR UNIT = 3 Kg

1+1

CAPACITY

CO

NFI

GU

RA

TIO

N

8xE1 75/120 OHM

- 732-102/71D

732-102/71A 732-102/71B

16xE1 75/120 OHM

Present only for 1+1 Configuration

A. Vergani

CMO-GS-NI-SE

Exec.:

Dept.:

Check:

Date

M. Brambilla

31-05-2006

Name:

Name:

Emiss.:

Var.:


IDU 16xE1 (1+0 or 1+1)

IDU 8xE1 (only 1+0)

LCT

ALMs

ALMs

USER/Dext Q-LAN

USER/Dext Q-LAN

1÷8V-LAN

V-LAN LCT

2 Mbit/s I/O TRIBUTARIES

SRAL XDs

9÷16

2 Mbit/s I/O TRIBUTARIES 1÷8

ODU CABLE 1

UDO

LB

HC

C

UD

LB

O C

LBC

DU

O ODU CABLE

ODU CABLE 2

HC

M

/W

NST

TE

MJ

C/

M/SWT J

MN

TE

C/

I O

I O

PS

PS


I

CAUTIONVbattery!

s SRAL XD

I

CAUTIONVbattery!

CAUTION! Vbattery



FUNCTIONS

INDOOR ASSEMBLY


Sheet 6

SINGLE - BOARD 2

POWER SUPPLYA I/O POWER ON - OFF

01 PS POWER SUPPLY Sheet 7

2nd IDU/ODU CONNECTION

1st IDU/ODU CONNECTION02

03 (NB1)ODU CABLE

ODU CABLE IMC 0257BEDG

IMC 0257BEDG

2Mb/s 75/120 Ohm

04a

04b (NB2)Sheet 8

Sheet 11ALARMS05 ALMS

64 Kb/s V11 DATA CHANNEL06 USER/Dext Sheet 13

BACK-UP MEMORY KEY

"F" INTERFACE EXPANSION FOR PCLCT

B

07 Sheet 15

10 Base T/100 Base Tx

10 Base T/100 Base Tx or

Q-LAN

V-LAN

08

09

Sheet 16

SeeFunctionsDescriptionRef.

IF

TRIBUTARY2Mb/s I/O TRIB.s 1÷8

2Mb/s I/O TRIB.s 9÷16

ALARM

SERVICE

SETTING

MANAGEMENT SYSTEM

-

-

NB1 = Present only for 1+1 ConfigurationNB2 = Present only for 16xE1 Capacity

07 LCT F INTERWORKING - S CHANNEL Sheet 15

A. Vergani

CMO-GS-NI-SE

Exec.:

Dept.:

Check:

Date

M. Brambilla

31-05-2006

Name:

Name:

Emiss.:

Var.:


VoIP Phone Sheet 19

07 01A0204a090805 06

07 0605 08 09 04a 04b 0302 A 01




IDU 8xE1 (only 1+0)

IDU 16xE1 (1+0 or 1+1)

V-LAN

sLCT

ALMs

SRAL XD

USER/Dext Q-LAN

sALMs

SRAL XD

USER/Dext Q-LAN

1÷8

V-LAN LCT

9÷16

CAUTION

ODU CABLE 1

!

O

UD

CBL

CH

Vbattery

ODU

CBL

CAUTIONVbattery!

CBL

O

UD

ODU CABLE

VbatteryCAUTION

!

ODU CABLE 2CH

N

W

MET

TS

/C

JM/

I O

I

PS

OI

C

JM

NM

W

ET

TS

//

I

PS



POWER SUPPLY

INDOOR ASSEMBLY


Sheet 7

SINGLE - BOARD 2

b) = THIS CABLE IS SUPPLIED WITH THE INSTALLATION MATERIALS, see IMC 0361BEDGIDU CONNECTION KIT-BASIC (597-525/16) see IMC 0361BEDG; FOR MOUNTING see IMC 0260BEDG

a) = THESE ACCESSORIES ARE CONTAINED IN THE POWER SUPPLY ACCESSORIES (332-055/28), PROVIDED WITH THE

RECOMMENDED WIRING

BREAKER

CABLE FOR POWER SUPPLY(105-013/02)

2x1.5 mm² BIPOLAR SHIELDED

(b)

(a)

PS (pin A3)

SRAL XD

METALLIC SHELL

(422-030/82)FOR 15C CONN.

= NEGATIVE

= POSITIVE

SIDE VIEW

POWER SUPPLYMAIN NEGATIVE

STATION

4A

-48 Vdc± 20%

NOMINALVOLTAGE

A3

A1

(a)

(a)

(422-060/16)

FEMALE CONTACT(422-027/31)

FEMALE CONNECTOR

CRIMPING

A3

A1

01

CONNECTIONS and PIN-OUT

(-38.4 to -57 Vdc)

PS

ND2

1+0 = 30W1+1 = 50W

ND 7...38GHz

1+0 = 35W1+1 = 70W

POWER CONSUMPTIONMAXIMUM

Pin A1

A. Vergani

CMO-GS-NI-SE

Exec.:

Dept.:

Check:

Date

M. Brambilla

31-05-2006

Name:

Name:

Emiss.:

Var.:


1+1 = 70W1+0 = 40W

HDe 7...38GHz

01

01




IDU 8xE1 (only 1+0)

IDU 16xE1 (1+0 or 1+1)

V-LAN

sLCT

ALMs

SRAL XD

USER/Dext Q-LAN

sALMs

SRAL XD

USER/Dext Q-LAN

1÷8

V-LAN LCT

9÷16

CAUTION

ODU CABLE 1

!

O

UD

CBL

CH

Vbattery

ODU

CBL

CAUTIONVbattery!

CBL

O

UD

ODU CABLE

VbatteryCAUTION

!

ODU CABLE 2CH

N

W

MET

TS

/C

JM/

I O

I

PS

OI

C

JM

NM

W

ET

TS

//

I

PS



INDOOR ASSEMBLY


Sheet 8

SINGLE - BOARD 2

04a 04b

CONNECTIONS

FOR 75 Ohm PIN-OUT SEE SHEET 9

b) = THIS MATERIAL IS SUPPLIED WITH THE INSTALLATION MATERIALS, see IMC 0361BEDG

2 Mbit/s I/O TRIBUTARIES 1÷8 (9÷16)

c) = THE LENGHT FOR THIS CABLE IS 300m MAX

75/120 Ohm TRIBUTARY INTERFACE

d) = THE LENGHT FOR THIS CABLE IS 200m MAX

FOR 120 Ohm PIN-OUT SEE SHEET 10

8xE1 120 Ohm (L=5/10/20/30 m)(314-331/79..82)

TRIBUTARY CABLE(a) (b)

8xE1 75 Ohm (L=5/10/20/30 m)TRIBUTARY CABLE

(314-331/35..38) (a) (b)

or

a) = THIS ASSEMBLED CABLE IS A PREFERRED SOLUTION; ON REQUEST IS POSSIBLE TO ORDER THE SINGLE MATERIALS AND TO MAKE THE CABLE IN FIELD (for P/N see IMC 0361BEDG andfor MOUNTING see IMC 0260BEDG) OR FOR SOLUTION WITH DIGITAL DISTRIBUTION FRAME (75 or 120 OHM) see IMC 0360BEDG

(d)

(c)

Pin 1

A. Vergani

CMO-GS-NI-SE

Exec.:

Dept.:

Check:

Date

M. Brambilla

31-05-2006

Name:

Name:

Emiss.:

Var.:


04a

04a 04b




IDU 8xE1 (only 1+0)

IDU 16xE1 (1+0 or 1+1)

V-LAN

sLCT

ALMs

SRAL XD

USER/Dext Q-LAN

sALMs

SRAL XD

USER/Dext Q-LAN

1÷8

V-LAN LCT

9÷16

CAUTION

ODU CABLE 1

!

O

UD

CBL

CH

Vbattery

ODU

CBL

CAUTIONVbattery!

CBL

O

UD

ODU CABLE

VbatteryCAUTION

!

ODU CABLE 2CH

N

W

MET

TS

/C

JM/

I O

I

PS

OI

C

JM

NM

W

ET

TS

//

I

PS




Sheet 9

( ) = CHANNEL NUMBERS ASSOCIATED TO "04b" CONNECTOR

75 Ohm TRIBUTARY INTERFACEPIN-OUT

SINGLE - BOARD 2INDOOR ASSEMBLY

04a 04b

= CABLE COAXIAL NUMBER

2

6

5

7

8

4

1

3

14

13

16

15

10

9

12

11

A. Vergani

CMO-GS-NI-SE

Exec.:

Dept.:

Check:

Date

M. Brambilla

31-05-2006

Name:

Name:

Emiss.:

Var.:






Sheet 10

( ) = CHANNEL NUMBERS ASSOCIATED TO "04b" CONNECTOR

SIDE VIEWSOLDERING

10

12

13

29

28

11

9

27

26

25

24

8

CHANNEL no. 6 ( 14 )Tx DATA Wire a

Tx DATA Wire b

Rx DATA Wire a

Rx DATA Wire b

23

7

6

22

5

21

4

3

20

19

18

2

1

14

16

17

15

33

32

31

30

50

49

48

47

46

45

44

42

43

41

40

38

39

37

36

34

35

Rx DATA Wire b

Rx DATA Wire a

Tx DATA Wire b

Tx DATA Wire aCHANNEL no. 5 ( 13 )

Tx DATA Wire a

Tx DATA Wire b

Rx DATA Wire a

Rx DATA Wire b

CHANNEL no. 8 ( 16 )

Rx DATA Wire b

Rx DATA Wire a

Tx DATA Wire b


Tx DATA Wire a

Tx DATA Wire b

Rx DATA Wire a

Rx DATA Wire b


Rx DATA Wire b

Rx DATA Wire a

Tx DATA Wire b


Tx DATA Wire a

Tx DATA Wire b

Rx DATA Wire a

Rx DATA Wire b


Tx DATA Wire a

Tx DATA Wire b

Rx DATA Wire a

Rx DATA Wire b


*

(connect the cable grounding wire to shell cable-clamp)

*

*

*

*

*

*

*

*

*

*

*

*

*

*

*

120 Ohm TRIBUTARY INTERFACEPIN-OUT

SINGLE- BOARD 2INDOOR ASSEMBLY

04a 04b

= CABLE COLOUR PAIRS* = TO THE CABLE CLAMP OF THE METALLIC SHELL

WH

RD

BU

GY

WH

OR

RD

GN

RD

WH

OR

WH

BU

BN

WH

GN

BK

BU

BN

GN

YE

BK

GY

RD

GY

BK

RD

BN

OR

BK

BU

BK

A. Vergani

CMO-GS-NI-SE

Exec.:

Dept.:

Check:

Date

M. Brambilla

31-05-2006

Name:

Name:

Emiss.:

Var.:





ALARMSINDOOR ASSEMBLY


CMO-GS-NI-SE

A. Vergani

Dept.:

Exec.:

Date:

Check:

14-07-2003

M. Brambilla

IMC 0359BEDG

Sheet 11

Name:

Name:

Var.:


SINGLE - BOARD 205

CONNECTION

a) = IF THIS CONNECTION IS REQUESTED IT HAS TO BE SEPARATELY PROVIDED; see IMC 0361BEDGFOR MOUNTING SEE IMC 0260BEDG

FOR PIN-OUT SEE SHEET 12

05

Pin 1

ALMs

05

(422-053/63)RJ45 CONNECTOR

4 PAIRS DOUBLE SHIELD CABLE(106-041/12)

(a)

(a)




IDU 8xE1 (only 1+0)

IDU 16xE1 (1+0 or 1+1)

V-LAN

sLCT

ALMs

SRAL XD

USER/Dext Q-LAN

sALMs

SRAL XD

USER/Dext Q-LAN

1÷8

V-LAN LCT

9÷16

CAUTION

ODU CABLE 1

!

O

UD

CBL

CH

Vbattery

ODU

CBL

CAUTIONVbattery!

CBL

O

UD

ODU CABLE

VbatteryCAUTION

!

ODU CABLE 2CH

N

W

MET

TS

/C

JM/

I O

I

PS

OI

C

JM

NM

W

ET

TS

//

I

PS




Sheet 12

ELECTRICAL DEFINITION

Output lines OPEN / CLOSED criteria

OPEN / normal criterion

Potential negative/positive to ground (from external souce)72VMax. voltage< 0,1 mAMax. sinking current

CLOSED / alarm criterion

Max. voltageMax. continuous current

Potential72V50 mA

negative/positive to ground (from external souce)

< 2VResidual voltage (on the contact)

PIN-OUT

SINGLE - BOARD 2

ALARMSINDOOR ASSEMBLY

05

A. Vergani

CMO-GS-NI-SE

Exec.:

Dept.:

Check:

Date

M. Brambilla

31-05-2006

Name:

Name:

Emiss.:

Var.:


1

2

3

4

5

6

7

8

TEST

GND

reserved

reserved

MINOR/WARNING

MAJOR

CRITICAL

POWER OFF output

output

output

output

output

-

-

-

SIGNAL NAMEPIN DIRECTION




USERINDOOR ASSEMBLY


CMO-GS-NI-SE

A. Vergani

Dept.:

Exec.:

Date:

Check:

14-07-2003

M. Brambilla

IMC 0359BEDG

Sheet 13

Name:

Name:

Var.:


SINGLE - BOARD 206

64 Kb/s V11

a) = IF THIS CONNECTION IS REQUESTED IT HAS TO BE SEPARATELY PROVIDED; see IMC 0361BEDGFOR MOUNTING SEE IMC 0260BEDG

FOR PIN-OUT SEE SHEET 14

06

Pin 1

USER/Dext

06

(422-053/63)RJ45 CONNECTOR

4 PAIRS DOUBLE SHIELD CABLE(106-041/12)

(a)

(a)

CONNECTION




IDU 8xE1 (only 1+0)

IDU 16xE1 (1+0 or 1+1)

V-LAN

sLCT

ALMs

SRAL XD

USER/Dext Q-LAN

sALMs

SRAL XD

USER/Dext Q-LAN

1÷8

V-LAN LCT

9÷16

CAUTION

ODU CABLE 1

!

O

UD

CBL

CH

Vbattery

ODU

CBL

CAUTIONVbattery!

CBL

O

UD

ODU CABLE

VbatteryCAUTION

!

ODU CABLE 2CH

N

W

MET

TS

/C

JM/

I O

I

PS

OI

C

JM

NM

W

ET

TS

//

I

PS




Sheet 14

USER/Dext64 Kb/s V11

PIN-OUT

SINGLE - BOARD 2INDOOR ASSEMBLY

06

a) = CONFIGURATION OF USER (CO/CONTRA-DIRECTIONAL CLOCK) or Dext/Dext SRA L Compatible channels

USER (a)

Dext (a)Contra-Directional

2

Dext-Dext SRA L Compatible (SubD 9 - RJ45)CONNECTION BETWEEN CHANNELS

17 21 5

36

36

8

94

4

87

IS A SOFTWARE CONTROLLED OPERATION

WIRING CABLE for

314-333/02 (L=3000mm)

SIGNAL NAME

DATA Rx wire a

3

2

5

7

8

4

PIN

6

1

Co-Directional (a)

output

output

input

output

output

A. Vergani

CMO-GS-NI-SE

Exec.:

Dept.:

Check:

Date

M. Brambilla

31-05-2006

Name:

Name:

Emiss.:

Var.:


DATA Rx wire b

CLOCK Rx wire a

CLOCK Rx wire b

DATA Tx wire a

DATA Tx wire b

CLOCK Tx wire a

CLOCK Tx wire b

input

input

input input

input

input

input

output

output

output

output

Contra-Directional (a)

DIRECTION

Dext (a)

DATA Rx wire a

DATA Rx wire b

CLOCK Rx wire a

CLOCK Rx wire b

DATA Tx wire a

DATA Tx wire b

CLOCK Tx wire a

CLOCK Tx wire b

SIGNAL NAME

4

8

6

7

5

2

3

1

PINDIRECTION

Dext SRAL Compatible (a)

input

output

output

input

input

input

input

output

output

input

input

input

input

input

output

output





Sheet 15

(PERSONAL COMPUTER RS-232 INTERFACE)

SINGLE - BOARD 2

LCTINDOOR ASSEMBLY

07

CONNECTION

A. Vergani

CMO-GS-NI-SE

Exec.:

Dept.:

Check:

Date

M. Brambilla

31-05-2006

Name:

Name:

Emiss.:

Var.:


The following equipment configuration is required :

PERSONAL COMPUTER SYSTEM REQUIREMENTS

CD-ROM driveRS-232C serial port

CPU 1,6 GHz

Pin-to-pin not-modem serial cable (necessary in case of connection on Finterface only)

40 GB hard disk

Mouse

256 Mbyte RAM (512 Mbyte suggested)

Video card with minimum resolution of 1024x768 and Color monitor

COMPUTERPERSONAL

RS-232 INTERFACEPERSONAL COMPUTER

LCT

INTERCONNECTION CABLE (L=1000mm)

The IP addresses of the network element SRAL XD must be the wich one of the network element SRA L +1; this connection can support MAX 3 LINK

a) = This material has to be separately provided; see IMC 0361BEDG

(314-332/48)(a)

F Interworking - S Channel(Prefer the V-Bus connection)

Pin 1

to existing SRA L(D01 Connector)

Ethernet network card

Software requirements :Microsoft Windows 2000 Professional (Service Pack 4) or Microsoft Windows XP (Service Pack 2)Microsoft Internet Explorer 6 or higherMicrosoft Excel 2000 SR-1 or higher (optional)TCP/IP communication protocol installed

07

07




IDU 8xE1 (only 1+0)

IDU 16xE1 (1+0 or 1+1)

V-LAN

sLCT

ALMs

SRAL XD

USER/Dext Q-LAN

sALMs

SRAL XD

USER/Dext Q-LAN

1÷8

V-LAN LCT

9÷16

CAUTION

ODU CABLE 1

!

O

UD

CBL

CH

Vbattery

ODU

CBL

CAUTIONVbattery!

CBL

O

UD

ODU CABLE

VbatteryCAUTION

!

ODU CABLE 2CH

N

W

MET

TS

/C

JM/

I O

I

PS

OI

C

JM

NM

W

ET

TS

//

I

PS




Sheet 16

10 Base T - 100 Base Tx

SINGLE - BOARD 2

QLAN / VLANINDOOR ASSEMBLY

09

V-LANQ-LAN

(10 Base T / 100 Base Tx)QLAN / VLAN

PIN-OUT

08

Pin 1

SEE SHEET 18 for SWITCHFOR TYPICAL CONNECTION: SEE SHEET 17 for Q/VLAN

A. Vergani

CMO-GS-NI-SE

Exec.:

Dept.:

Check:

Date

M. Brambilla

31-05-2006

Name:

Name:

Emiss.:

Var.:


SIGNAL NAME

DATA Tx wire b

3

2

5

7

8

4

PIN

6

1

DIRECTION

-

-

-

-

output

output

input

DATA Tx wire a

DATA Rx wire b

DATA Rx wire a

not used

not used

not used

not used

input

0908

08 09




IDU 8xE1 (only 1+0)

IDU 16xE1 (1+0 or 1+1)

V-LAN

sLCT

ALMs

SRAL XD

USER/Dext Q-LAN

sALMs

SRAL XD

USER/Dext Q-LAN

1÷8

V-LAN LCT

9÷16

CAUTION

ODU CABLE 1

!

O

UD

CBL

CH

Vbattery

ODU

CBL

CAUTIONVbattery!

CBL

O

UD

ODU CABLE

VbatteryCAUTION

!

ODU CABLE 2CH

N

W

MET

TS

/C

JM/

I O

I

PS

OI

C

JM

NM

W

ET

TS

//

I

PS




Sheet 17

SINGLE - BOARD 2

IDU-1

ODU

CONTROLLER

ODU

IDU-2

CONTROLLER

- Use IP address 10.10.X.Y, where X identifies the station (0 < X < 255) and Y identifies the network element

If it has not been defined a network plan, insert the IP addresses as pointed out here below:If there is a network plan for the management system, insert the IP addresses as it has been foreseen

a) = IF THIS CONNECTION IS REQUESTED THE MATERIALS HAS TO BE SEPARATELY PROVIDED; see IMC 0361BEDG

TNMSSERVER

NETVIEWERSERVER

INDOOR ASSEMBLYQLAN / VLAN

Q/VLAN CONNECTIONS

(314-324/54)

- Use NETMASK 255.255.255.0 into every radio

The controller must have an IP network address.

into the station (1 < Y < 254 only even values).For Example:

ST. A IDU-1 10.10.8.1 255.255.255.0

ST. B IDU-1 10.10.9.1 255.255.255.0ST. C IDU-1 10.10.10.1 255.255.255.0

b) = MAX 64 NETWORK ELEMENTS

Q (100BASET) ETHERNET

GATEWAY N.E.

08IDU SRAL XD

IDU-3 10.10.8.5 IDU-2 10.10.8.3

IP ADDRESS NETMASK

SWITCH

(b)

ST. A

(100BASET)

(100BASET)

INTERCONNECTION CABLE (L=1000mm)

CONTROLLER

(a)

SRAL XD

0908

IDU-3

ODU

CONTROLLER

ST. D

SRAL XD

0908

ODU

IDU-1

L max = 100m

SRAL XD

08 09

ST. C

SRAL XD

08 09

08 09

CLIENTSWITCH

(100BASET)

(100BASET)

TNMS/NETVIEWER

(100BASET)

SRAL XD

SRAL XD

ST. B

CONTROLLER08 09

IDU-1

ODU

CONTROLLER08 09

IDU-1

ODU

A. Vergani

CMO-GS-NI-SE

Exec.:

Dept.:

Check:

Date

M. Brambilla

31-05-2006

Name:

Name:

Emiss.:

Var.:






Sheet 18

SINGLE - BOARD 2

(106-041/76)4 Pairs Shielded CABLE

RJ45 Shielded CONNECTOR

- Use IP address 10.10.X.Y, where X identifies the station (0 < X < 255) and Y identifies the network element

If it has not been defined a network plan, insert the IP addresses as pointed out here below:If there is a network plan for the management system, insert the IP addresses as it has been foreseen

a) = IF THIS CONNECTION IS REQUESTED THE MATERIALS HAS TO BE SEPARATELY PROVIDED; see IMC 0361BEDG

SERVER

NETVIEWERSERVER

INDOOR ASSEMBLYQLAN / VLAN

SWITCH CONNECTIONS

(to be made in field)

ST. D IDU-1 10.10.11.1 255.255.255.0

FOR MOUNTING see IMC 0260BEDG

- Use NETMASK 255.255.255.0 into every radio

The controller must have an IP network address.

into the station (1 < Y < 254 only even values).For Example:

ST. A IDU-1 10.10.8.1 255.255.255.0

ST. B IDU-1 10.10.9.1 255.255.255.0ST. C IDU-1 10.10.10.1 255.255.255.0

b) = MAX 64 NETWORK ELEMENTS

ST. A

IP ADDRESS NETMASK

IDU-3 10.10.8.5 IDU-2 10.10.8.3

SWITCH

(100BASET)

(422-053/63)

(100BASET)TNMS

INTERCONNECTION CABLE (STRAIGHT THRU Cable)

SRAL XD

SRAL XD

(a)

08

ST. D

08

IDU-3

ODU

CONTROLLER09

ODU

IDU-1

CONTROLLER09

SRAL XD

CONTROLLER

L max = 100m

08 09

IDU-2

ODU

SRAL XD

CONTROLLER

ST. C

08 09

IDU-1

ODU

08 09

CLIENTSWITCH

(100BASET)

(100BASET)

TNMS/NETVIEWER

(a)

(a)

(100BASET)

SWITCH

ODU

IDU-1

ODU

CONTROLLER

IDU-1

CONTROLLER

08

SRAL XD

09

ST. B

08

SRAL XD

09

A. Vergani

CMO-GS-NI-SE

Exec.:

Dept.:

Check:

Date

M. Brambilla

31-05-2006

Name:

Name:

Emiss.:

Var.:






Sheet 19

A. Vergani

CMO-GS-NI-SE

Exec.:

Dept.:

Check:

Date

M. Brambilla

31-05-2006

Name:

Name:

Emiss.:

Var.:


(314-329/59)RJ45 cross cable L.5m

(ON SPECIFIC REQUEST ONLY)

INDOOR ASSEMBLYIP PHONE (48Vdc / 220Vac)

SINGLE - BOARD 2

Connection

RJ45 CONNECTOR

09

09

IP PHONE (48Vac / 220Vdc)(634-901/15)

09

09




IDU 8xE1 (only 1+0)

IDU 16xE1 (1+0 or 1+1)

V-LAN

sLCT

ALMs

SRAL XD

USER/Dext Q-LAN

sALMs

SRAL XD

USER/Dext Q-LAN

1÷8

V-LAN LCT

9÷16

CAUTION

ODU CABLE 1

!

O

UD

CBL

CH

Vbattery

ODU

CBL

CAUTIONVbattery!

CBL

O

UD

ODU CABLE

VbatteryCAUTION

!

ODU CABLE 2CH

N

W

MET

TS

/C

JM/

I O

I

PS

OI

C

JM

NM

W

ET

TS

//

I

PS





IMC 0359BEDG



INSTALL. INFORMATION for SINGLE-BOARD 2 INDOOR ASSEMBLY Sheet 20

SINGLE – BOARD 2 INDOOR ASSEMBLY

REVISION LIST

Revisions Revisions Sheet 01 02 03 04 05 06 07 08 09 10 Sheet 01 02 03 04 05 06 07 08 09 10 01 ¯ ¯ - 02 ¯ ¯ - 03 ¯ ¯ - 04 ¯ ¯ - 05 ¯ ¯ - 06 ¯ ¯ - 07 ¯ ¯ - 08 ¯ ¯ - 09 ¯ ¯ - 10 ¯ ¯ - 11 ¯ ¯ - 12 ¯ ¯ - 13 ¯ ¯ - 14 ¯ ¯ - 15 ¯ ¯ - 16 ¯ ¯ - 17 ¯ ¯ - 18 ¯ ¯ - 19 ¯ ¯ - 20 ¯ ¯ - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -



LOW CAPACITY DIGITAL RADIO SYSTEMINSTALLATION INFORMATION for SOLUTION with 2Mb/s D.D.F.


CMO-GS-NI-SE

A. Vergani

Dept.:

Exec.:

Date:

Check:

31-05-2006

M. Brambilla

IMC 0360BEDG

Sheet 1/6

Name:

Name:

Var.:


Lay-Out

2Mb/s Digital Distribution Frame

IN

OUT1 RADIO LINK

cd

ab

2 RADIO LINK 3 RADIO LINK 4 RADIO LINK / SERVICE

2Mb/s Digital Distribution Frame (120 Ohm)


SINGLE-BOARD

(See IMC 0359BEDG)


19" or N3 ETSI RACK

D.D.F. (120 Ohm)(232-334/92)

(up to 8 8xE1 or 4 16xE1)

see Sheets 2...3

SINGLE-BOARD


19" or N3 ETSI RACK(See IMC 0359BEDG)see Sheets 4...5

D.D.F. (75 Ohm)(232-334/86)

(up to 6 8xE1 or 3 16xE1)

4444

4444

4410

0




V-LAN

sLCT

ALMs

SRAL XD

USER/Dext Q-LAN

sALMs

SRAL XD

USER/Dext Q-LAN

1÷8

V-LAN LCT

9÷16

CAUTION

ODU CABLE 1

!

O

UD

CBL

CH

Vbattery

ODU

CBL

CAUTIONVbattery!

CBL

O

UD

ODU CABLE

VbatteryCAUTION

!

ODU CABLE 2CH

N

W

MET

TS

/C

JM/

I O

I

PS

OI

C

JM

NM

W

ET

TS

//

I

PS


Q-LAN

LCT

sALMs USER/Dext

SRAL XD

USER/Dext

sALMs

SRAL XD

LCTQ-LAN V-LAN

V-LAN


1÷8

ODU CABLE 2

9÷16

CAUTION CAUTION

Vbattery

ODU CABLE

CAUTION

DU

O

LBC

!

! Vbattery

ST

TE

! Vbattery

ODU CABLE 1CB

CDO

HLUCH

DO

BC

LU

/W

MN /

MJ

C

I

I O

OI

M

C/

JS

TE

/

MN

T W I

PS

PS





CMO-GS-NI-SE

A. Vergani

Dept.:

Exec.:

Date:

Check:

31-05-2006

M. Brambilla

IMC 0360BEDG

Sheet 2

Name:

Name:

Var.:


CONNECTION


IN

OUT1 RADIO LINK

cd

ab

2 RADIO LINK 3 RADIO LINK 4 RADIO LINK / SERVICE

SINGLE-BOARD 2


19" or N3 ETSI RACK

D.D.F. (120 Ohm)

1÷8 TRIBUTARY INTERFACE 120 Ohm

FRONT VIEW120 Ohm W.W. D.D.F. (a)

Assembled TRIBUTARY CABLE(a) ( 314-332/54 )

Wire-Wrap MODULE

COVER

04a

EXAMPLE2Mb/s 120 Ohm STREAMS CONNECTIONS

(supplied with the D.D.F.)

(assembled on the TRIBUTARY CABLE)

(232-334/92)

9÷16 TRIBUTARY INTERFACE 120 Ohm 04b

a) = THIS MATERIAL IS SUPPLIED WITH THE INSTALLATION MATERIALS, see IMC 0361BEDG; FOR WIRING see SHEET 3

8xE1 120 Ohm

Wire-Wrap MODULE

8

REAR VIEW

13d

16 1415 12 11 10 9

c

b

a

37 6 5 4 2 1

HOOK

hook positioned in the bottomMount the WW Module with the

WARNING

ODU CABLEV-LAN

LCTs

ALMs USER/Dext

SRAL XD

Q-LAN 1-8


9-16

D CBD CBU HL U HL

ODU CABLEO C O C

/ MST W J

TE

M CN /

+ -

PS

4 RADIO LINK / SERVICE

IN

OUT ba

dc

1 RADIO LINK 2 RADIO LINK 3 RADIO LINK

2 Mbit/s I/O TRIBUTARIES 1-8

s

ALMs USER/Dext

SRAL XD

Q-LAN V-LAN LCTODU CABLE

C

LB

O

UD

HC

MTE N

T WS /

/C

JM

PS

+ -

1÷8 TRIBUTARY INTERFACE 120 Ohm04a


CAUTIONVbattery!

CBL

O

UD

ODU CABLE

OI

C

JM

NM

W

ET

TS

//

I

+ -

PS

sLCT

ALMs Q-LANUSER/Dext

SRAL XD

V-LAN

UDO

LBC

VbatteryCAUTION

!

ODU CABLE 1

HC

CAUTIONVbattery

ODU CABLE 2

!

UDO

LBC

HC

T

TSE

/

M

W

NC

JM/

I O

I

+

PS

-

sALMs USER/Dext

SRAL XD

V-LANQ-LAN LCT


1-8 9-16

2 Mbit/s I/O TRIBUTARIES 1-8





CMO-GS-NI-SE

A. Vergani

Dept.:

Exec.:

Date:

Check:

31-05-2006

M. Brambilla

IMC 0360BEDG

Sheet 3

Name:

Name:

Var.:


2Mb/s Digital Distribution Frame (120 Ohm)Wiring for Sub-D Tributary

wire a16

TX8wire a6DATA In

22 wire b

3

25

248

723

182

9

19

DATA Out

DATA In

DATA Out

DATA In

DATA Out

30

420

521

14

3115

32

DATA Out

DATA In

DATA In

DATA Out

DATA In

RX6wire a

wire b

wire b

wire a

wire a

wire b

wire a

wire bwire a

wire b

RX8

TX7

TX6

RX7

wire b

wire b

wire a

wire a

wire b

wire awire b

wire awire b

TX5

RX5

RX4

TX4

TX3

1÷8/9÷16Pin on Sub-D

Description

13

27

10

1733

26

1228

11

29

DATA Out

DATA In

DATA Out

DATA Out

DATA In

wire a

wire b

wire b

wire a

wire a

wire b

wire b

wire a

wire a

wire b

RX3

TX2

TX1

RX2

RX1

11c3cwhite

16c8cblack

Channel on Connector

grey

1÷8 9÷16

8d 16d

black

brown

yellow

blue

green

black

blue

black

black

orange

Ch.7

Ch.8

Ch.6

orange

brown

red

grey

red

green

red

grey

red

Ch.5

Ch.4

14a6a

Ch.15

Ch.16

Ch.14

7b

8a8b

7d7c

6d

7a

6c

6b

15b

16a16b

15d15c

14d

15a

14c

14b

Ch.12

Ch.13

4d

5c5d

5b5a

4b

4c

4a

3d

12d

13c13d

13b13a

12b

12c

12a

11d

Pin on Wire-Wrap module

white

brown

blue

red

green

white

blue

white

white

orange

Ch.2

Ch.3

Ch.1

CableColours

Pairs

9a1a

Ch.10

Ch.9

Ch.11

2b

3b3a

2d2c

2a

1d

1b1c

10b

11b11a

10d10c

10a

9d

9b9c

1st1÷8

2nd9÷16






CMO-GS-NI-SE

A. Vergani

Dept.:

Exec.:

Date:

Check:

31-05-2006

M. Brambilla

IMC 0360BEDG

Sheet 4

Name:

Name:

Var.:


CONNECTION


SINGLE-BOARD


19" or N3 ETSI RACK

D.D.F. (75 Ohm)

(a)

c) = THIS MATERIAL IS SUPPLIED WITH THE INSTALLATION MATERIALS, see IMC 0361BEDG

1÷8 75 Ohm Assembled TRIBUTARY CABLE ( 314-330/99 )

(c)

4 8 12 16 4 8

2

3

1

OUTIN

6

7

5

OUTIN

10

11

9

OUTIN ININ

14

15

13

OUTIN

2

3

1

OUT

6

7

5

OUT

b) = THESE MATERIALS and 8 Coaxial Plug 1.0/2.3 (421-015/60) ARE INCLUDED IN THE 8xE1 75 Ohm Tributary Cable KIT(332-055/41)a) = THESE MATERIALS and 16 Coaxial Plug 1.0/2.3 (421-015/60) ARE INCLUDED IN THE 16xE1 75 Ohm Tributary Cable KIT(332-055/42)

EXAMPLE2Mb/s 75 Ohm STREAMS CONNECTIONS



(b)(c)

(a)(c)

1-8


ALMs

sLCT

SRAL XD

USER/Dext Q-LAN V-LAN

9÷16 TRIBUTARY INTERFACE 75 Ohm 04b


9-16

CO

LUBD

ODU CABLE

HC

CO

LUBD

ODU CABLE

HC

NM

ET

WTS /

/C

JM

PS

+ -

(232-334/86)75 Ohm Coax D.D.F. (c)

FRONT VIEW(b)

(assembled on the TRIBUTARY CABLES)1÷16 Coaxial MODULE

(a)(c)

4

2

3

IN

1

OUT

(c)1÷8 Coaxial MODULE

(assembled on the TRIBUTARY CABLE)

13

14

16

15

OUT

8

6

7

IN

5

IN

12

10

11

OUT

9

IN OUTOUT

4

2

3

IN

1

IN

8

6

7

OUT

5

s

ALMs

SRAL XD

USER/Dext Q-LAN V-LAN LCT 1-82 Mbit/s I/O TRIBUTARIES

D BLU

O CCH

ODU CABLE

MS /T W J

ET

NM C

/

+

PS

-





V-LAN

sLCT

ALMs

SRAL XD

USER/Dext Q-LAN

sALMs

SRAL XD

USER/Dext Q-LAN

1÷8

V-LAN LCT

9÷16

CAUTION

ODU CABLE 1

!

O

UD

CBL

CH

Vbattery

ODU

CBL

CAUTIONVbattery!

CBL

O

UD

ODU CABLE

VbatteryCAUTION

!

ODU CABLE 2CH

N

W

MET

TS

/C

JM/

I O

I

PS

OI

C

JM

NM

W

ET

TS

//

I

PS





CMO-GS-NI-SE

A. Vergani

Dept.:

Exec.:

Date:

Check:

31-05-2006

M. Brambilla

IMC 0360BEDG

Sheet 5

Name:

Name:

Var.:


Coax CableNo.

OUT1

OUT2

OUT3

OUT4

OUT5

OUT7

OUT6

OUT8

2Mb/s Digital Distribution Frame (75 Ohm)Wiring for Sub-D Tributary

Rx5DATA Out21

25

23

22

24

19

18

20

DATA Out

DATA Out

DATA In

DATA In

DATA Out

DATA In

DATA In

Rx7

Rx8

Tx8

Tx7

Rx6

Tx6

Tx5

IN8

IN7

IN6

IN5

1÷8/9÷16Pin on Sub-D Description

30

32

31

26

33

28

27

DATA Out

DATA In

DATA In

DATA Out

DATA Out

DATA In

DATA In

29 DATA Out

Tx4

Rx4

Tx3

Rx3

Tx2

Tx1

Rx2

IN4

IN3

IN2

IN1

Rx1

Ch.13OUT13OUT5

Ch.5IN13

IN14

OUT14

IN15

IN16

OUT16

OUT15

Channel on Connector

IN5

IN6

IN7

OUT7

OUT6

IN8

OUT8

1÷8

Ch.7

Ch.6

Ch.8

9÷16

Ch.14

Ch.16

Ch.15

2nd9÷16

OUT9

IN10

OUT11

OUT10

IN11

IN12

OUT12

1st1÷8

Coaxial Module

IN1

OUT2

OUT1

IN2

IN3

OUT4

OUT3

IN4

Ch.3

Ch.2

Ch.4

Ch.1

Ch.10

Ch.12

Ch.11

IN9Ch.9






IMC 0360BEDG



INSTALL. INFORMATION for SOLUTION with 2Mb/s D.D.F. Sheet 6

2Mb/s Digital Distribution Frame

REVISION LIST

Revisions Revisions Sheet 01 02 03 04 05 06 07 08 09 10 Sheet 01 02 03 04 05 06 07 08 09 10 01 ¯ ¯ - 02 ¯ ¯ - 03 ¯ ¯ - 04 ¯ ¯ - 05 ¯ ¯ - 06 ¯ ¯ - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -



( )CRIMPINGSIDE VIEW

IMC 0260BEDG

Sheet 1/24

FEMALE CONTACT(422-027/31)

A3

FEMALE CONNECTOR(422-060/16)

A1

(FRONT VIEW)

(422-060/16, 422-027/31)Power Supply Connector

Name:

Name:

A. VerganiEmiss.:

Var.:

05-0301Ed.:

Ed.:

A. Vergani

CMO-GS-NI-SE

M. Brambilla

12-05-2003

Check:

Date:

Exec.:

Dept.:

ASSEMBLING INDOOR ACCESSORIES

INSTALLATION INFORMATION for ASSEMBLING INDOOR ACCESSORIESLOW CAPACITY DIGITAL RADIO SYSTEM

SRAL XD

06 06-07 A. Vergani



IMC 0260BEDG

Sheet 2

with 2x1,5 sq.mm Bipolar Shielded Power Supply Cable (105-013/02)Power Supply Connector (422-060/16, 422-027/31)

Name: A. VerganiEmiss.: 05-0301Ed.:A. Vergani

CMO-GS-NI-SE

M. Brambilla

12-05-2003

Check:

Date:

Exec.:

Dept.:


6.5

4 - Place the CONTACT RING against the contact bush

3 - Position the CABLE-RING at the distance shown in the figure.

SHEATH

CABLE-RING

SHEATH

CABLE-RING

RINGCONTACT

RING

BRAID

CONTACT

RING

BRAID

CONTACT

2 - Insert the cable through the CABLE-RING and through the CONTACT RING.

1 - Remove the sheath to a length suitable for the dimensions of the ferrule.

SHEATH

SHEATH

BRAID

BRAID


SRAL XD




SRAL XDLOW CAPACITY DIGITAL RADIO SYSTEM

IMC 0260BEDG

Sheet 3

with 2x1,5 sqmm Bipolar Shielded Power Supply Cable (105-013/02)Power Supply Connector (422-060/16, 422-027/31)


CMO-GS-NI-SE

M. Brambilla

12-05-2003

Check:

Date:

Exec.:

Dept.:

INSTALLATION INFORMATION for ASSEMBLING INDOOR ACCESSORIES


and crimp them with the CRIMP TOOL 323-003/19 (See IMC 0262BEDG)

7 - Insert the two unsheathed wires into the FEMALE CONTACTS (422-027/31) as shown on the drawing.

(422-027/31)FEMALE CONTACTS

6 - Unsheath the two wires as shown on the drawing.

4mm

5 - Cut the METAL BRAID to a length of 9-10 mm and bend it back to cover the CONTACT RING

BRAID

CONTACTRING

SHEATH




IMC 0260BEDG

Sheet 4


CMO-GS-NI-SE

M. Brambilla

12-05-2003

Check:

Date:

Exec.:

Dept.:



SRAL XD

2

9- Insert the whole (i.e. cable and connector) into the METALLIC SHELL as stated at pages 11...14

1ascertain that the contacts are securely snap-fastened into position.

Power supply Connector (422-060/16, 422-027/31)with 2x1,5 sqmm Bipolar Shielded Power Supply Cable (105-013/02)

8 - Insert the contact with the 1-brand cable set to pos. "A1" and the contact with the 2-brand cable set to pos."A3",

A1

A3




IMC 0260BEDG

Sheet 5

Name:

Name:

A. VerganiEmiss.:

Var.:

05-0301Ed.:A. Vergani

CMO-GS-NI-SE

M. Brambilla

12-05-2003

Check:

Date:

Exec.:

Dept.:



SRAL XD

A. Vergani06-0706Ed.:

Sub-D 50 Contacts Connector (422-062/89)with 75 Ohm Coaxial Cable (104-102/23)

1. Insert the HEATSHRINK SLEEVE with length 40 mm on the cable and trim the OUTER SHEATH according to the measures pointed out here below.

2. Trim the SHEATH, the BRAID, the DIELECTRIC and the CENTRAL CONDUCTOR of all the eight single cables according to the measures pointed out here below.

3. Position the HEATSHRINK SLEEVE on the OUTER SHEATH and on the INNER

Heat the heatshrink sleeve ensuring that it adheres well on the inner and outer sheaths.

ones, as pointed out here below.

HEATSHRINK SLEEVE

HEATSHRINK SLEEVE

OUTER SHEATH

SHEATH

OUTER SHEATH

HEATSHRINK SLEEVE

CONDUCTOR

50

INNER SHEATH

30

BRAID

10

DIELECTRIC

3

CENTRAL

95 mm

ONLY IF DO NOT USE THE PREFERRED SOLUTION OF ASSEMBLED CABLE



IMC 0260BEDG

Sheet 6

Name:

Name:

A. VerganiEmiss.:

Var.:


CMO-GS-NI-SE

M. Brambilla

12-05-2003

Check:

Date:

Exec.:

Dept.:



SRAL XD


To SHELL CABLE

Sub-D 50 Contacts Connector (422-062/89)with 75 Ohm Coaxial Cable (104-102/23)

4. Connect the cable to the connector. Use a piece of the central conductor to execute the ground

5. Insert the cable and the connector into the METALLIC SHELL, as stated at pages 11 - 12 - 13 - 14. Pay maximum attention to connect all the BRAIDS of the single cables to the cable clamp of the shell itself.

inner connections.

CLAMPPIN 1



IMC 0260BEDG

Sheet 7

Name:

Name:

A. VerganiEmiss.:

Var.:


CMO-GS-NI-SE

M. Brambilla

12-05-2003

Check:

Date:

Exec.:

Dept.:



SRAL XD

10RUBBER

CABLE-RING

SHEATHBRAID

SHEATHBRAID

3 - Position the rubber CABLE-RING at the distance shown in the figure.

2 - Insert the cable through the rubber CABLE-RING.


SHEATHBRAID

RUBBER

CABLE-RING

Sub-D 50 Contacts Connector (422-062/89)with Multipairs Cable (Metallic Shell)


ONLY IF DO NOT USE THE PREFERRED SOLUTION OF ASSEMBLED CABLE



IMC 0260BEDG

Sheet 8


CMO-GS-NI-SE

M. Brambilla

12-05-2003

Check:

Date:

Exec.:

Dept.:



SRAL XD

Sub-D 50 Contacts Connector (422-062/89)with Multipairs Cable (Metallic Shell)

SHEATH

RIBBONMETAL

CABLE GROUNDWIRE

BRAID

BRAIDSHEATH

WIRECABLE GROUND

CABLE-RINGRUBBER

CABLE-RINGRUBBER

4 - Cut the METAL BRAID and the ground wire to a lenght of 10 mm to cover the sheath.

5 - Cut the METAL RIBBON to completely free the twisted pairs.

CABLE GROUNDWIRE

SHEATH

CABLE-RING

RUBBER

BRAID

7 - Connect the cable to the connector.

CONNECTOR

8 - Fit both (cable and connector) into the METALLIC SHELL as stated at pages 15..18.

6 - Locate the pair ground wires like the cable ground wire.

BRAID

PAIR GROUNDWIRE

SHEATH

CABLE-RINGRUBBER

Do not made this operation if the pair ground wires are connected to the grounding point on the DDF.

1st Sh.

16th Sh.

1a

1b

16b

16a




IMC 0260BEDG

Sheet 9


CMO-GS-NI-SE

M. Brambilla

12-05-2003

Check:

Date:

Exec.:

Dept.:



SRAL XD

6.5

4 - Place the CONTACT RING against the contact bush

3 - Position the CABLE-RING at the distance shown in the figure.

SHEATH

CABLE-RING

SHEATH

CABLE-RING

RINGCONTACT

RING

BRAID

CONTACT

RING

BRAID

CONTACT

2 - Insert the cable through the CABLE-RING and through the CONTACT RING.


with Multipairs Cable (Shielded Shell)Sub-D 9-15 Contacts Connector (422-062/60, 86)

SHEATH

SHEATH

BRAID

BRAID




IMC 0260BEDG

Sheet 10


CMO-GS-NI-SE

M. Brambilla

12-05-2003

Check:

Date:

Exec.:

Dept.:



SRAL XD

with Multipairs Cable (Shielded Shell)Sub-D 9-15 Contacts Connector (422-062/60, 86)

5 - Cut the METAL BRAID and the ground wire to a lenght of 9-10 mm and bend them back over the contact ring.

RINGCONTACT

Cut the METAL RIBBON to completely free the twisted pairs.

BRAID

BRAID

RINGCONTACT

SHEATH

SHEATH

WIREGROUND

WIRE

METALRIBBON

GROUND

GROUNDWIRE

6 - Connect the cable to the connector.

CONNECTOR

SHEATHBRAID

7 - Fit both (cable and connector) into the shielded shell as stated at pages 15..18.




IMC 0260BEDG

Sheet 11


CMO-GS-NI-SE

M. Brambilla

12-05-2003

Check:

Date:

Exec.:

Dept.:



SRAL XD

A

B±0.3

33,3 1115.4

FMax

E±0.3

4140,3

D±0.3

C±0.3

E

No.

1615

±0.3ACONTACTS

422-030/82

P/N

C

B

4-40UNC-2A

Metallic Shell (422-030/82 and 422-058/81)

F

Rubber Cable-Ring

Fixing Screws

45°

D49.4

18.5422-058/81 4250 4867.861.1 15




IMC 0260BEDG

Sheet 12


CMO-GS-NI-SE

M. Brambilla

12-05-2003

Check:

Date:

Exec.:

Dept.:



SRAL XD


1 - Fit both (cable and connector) into the shell and position the cable ring in its appropriate seat.

METALLIC SHELL

CONNECTOR

RUBBER

CABLE-RING

CABLE

CABLE CLAMP

2 - Fix the CABLE CLAMP with the two screws supplied.

SCREW

CABLE




IMC 0260BEDG

Sheet 13


CMO-GS-NI-SE

M. Brambilla

12-05-2003

Check:

Date:

Exec.:

Dept.:



SRAL XD


4 - Close the two HALVES OF THE SHELL by pressing them together with a hand press

3 - Fit the two FIXING SCREWS in the appropriate seats of the shell.

FIXINGSCREW

FIXINGSCREW

CABLE




IMC 0260BEDG

Sheet 14


CMO-GS-NI-SE

M. Brambilla

12-05-2003

Check:

Date:

Exec.:

Dept.:



SRAL XD


5 - Fix the two halves of the shell inserting and screwing a screw on both sides into the proper available seats




IMC 0260BEDG

Sheet 15


CMO-GS-NI-SE

M. Brambilla

12-05-2003

Check:

Date:

Exec.:

Dept.:



SRAL XD

4 m

ax.

C

39.62

31.30

max B

923,3

max F

823,3

E

16.533.3

D I M E N S I O N S

-

D

25

C

B

No.

1515

15

max ACONTACTS

9

422-030/92

422-030/91

P/N

A

Shielded Shell (422-030/91...92)

1833

F

D

8

E

39.1

5 m

ax

42.1

5 m

ax

37.5




IMC 0260BEDG

Sheet 16


CMO-GS-NI-SE

M. Brambilla

12-05-2003

Check:

Date:

Exec.:

Dept.:



SRAL XD


1 - Fit both (cable and connector) into the shielded shell and position the cable ring in its appropriate seat.

CONNECTOR

SHIELDED SHELLCABLE-RING

CABLE




IMC 0260BEDG

Sheet 17


CMO-GS-NI-SE

M. Brambilla

12-05-2003

Check:

Date:

Exec.:

Dept.:



SRAL XD


CABLE CLAMP

SCREW

Choose the more suitable for the size of the cable and discard the other one in accordance with the table below.

B = LARGE

* A = SMALLDIAM.

4 - 66 - 8

CABLE

8 - 105 - 8

B

BA

CABLE CLAMP

A

*

2 - Fix the CABLE CLAMP with the three screws supplied. Each shell is equipped with two different cable clamps.

P/N

422-030/91

422-030/92

9

15

No.CONTACTSSHELL




IMC 0260BEDG

Sheet 18


CMO-GS-NI-SE

M. Brambilla

12-05-2003

Check:

Date:

Exec.:

Dept.:



SRAL XD


4 - Close the two HALVES OF THE SHELL by pressing them together with a hand press

3 - Fit the two FIXING SCREWS in the appropriate seats of the shell.

SCREWFIXING

FIXINGSCREW




IMC 0260BEDG

Sheet 19

Name:

Name:

A. VerganiEmiss.:

Var.:


CMO-GS-NI-SE

M. Brambilla

12-05-2003

Check:

Date:

Exec.:

Dept.:



SRAL XD

Self Locking Coaxial Plug (421-015/60)for

75 Ohm Coaxial Cable (104-102/21)

SELF-LOCKING COAXIAL PLUGSERIES 1.0/2.3 - 75 Ohm

(421-015/60)


(104-102/21)TCE 2HH2 1(0.4-1.9)/M

75 Ohm COAXIAL CABLE



IMC 0260BEDG

Sheet 20

Name:

Name:

A. VerganiEmiss.:

Var.:


CMO-GS-NI-SE

M. Brambilla

12-05-2003

Check:

Date:

Exec.:

Dept.:



SRAL XD

Self Locking Coaxial Plug (421-015/60)for

75 Ohm Coaxial Cable (104-102/21)

1 - Insert the ferrule over the cable and cut the sheath, the braid, the dielectric and central conductoraccording to the measurements indicated here below

2 - Introduce the central conductor until resting on the dielectric, crimp by crimp tool

3 - Introduce the central conductor in the coaxial plug until the central conductor blocksarrange the braid on plug body and push the ferrule until it rests against the plugcrimp by crimp tool 236-100/40 (See IMC 0262BEDG)

(236-100/40)

3.8 x 8

0.7

inspection hole

-0.2

-0.512.5

8 -0.5 4.9




IMC 0260BEDG

Sheet 21

Name:

Name:

A. VerganiEmiss.:

Var.:


CMO-GS-NI-SE

M. Brambilla

12-05-2003

Check:

Date:

Exec.:

Dept.:



SRAL XD

with Cable (106-041/12 or 106-041/76)RJ45 Shielded Connector (422-053/63)

1 - Put the protection plastic shell of the connector over the cable

2 - Unsheath the cable as shown in the figure

25mm

3 - Bend back the braided shield over the cable sheath and remove the tinfoil shield.

4 - Separate the pairs and make the wires as parallel as possible




IMC 0260BEDG

Sheet 22

Name:

Name:

A. VerganiEmiss.:

Var.:


CMO-GS-NI-SE

M. Brambilla

12-05-2003

Check:

Date:

Exec.:

Dept.:



SRAL XD


7 - Insert the connector in the crimping matrix of the tool and crimp the connector executing the proper pressure until the limit

5 - Cut the wires with accuracy as shown in figure by means of the provided tool 236-100/17 (See IMC 0262BEDG)

6 - Insert the cable into the connector taking care each single wire is properly placed.Push the wires in position The connector transparency allows to verify the correctness of the operation

15mm

RJ45




IMC 0260BEDG

Sheet 23

Name:

Name:

A. VerganiEmiss.:

Var.:


CMO-GS-NI-SE

M. Brambilla

12-09-2003

Check:

Date:

Exec.:

Dept.:



SRAL XD


8 - Remove the exceeding shield

9 - Put the plastic shell over the connector

SHIELD TO BE REMOVED






IMC 0260BEDG

SRAL XD

LOW CAPACITY DIGITAL RADIO SYSTEM INSTALLATION INFORMATION for ASSEMBLING INDOOR ACCESSORIES Sheet 24


REVISION LIST


Sheet 01 02 03 04 05 06 07 08 09 10

01 ¯ ¯ ¯ ¯ ¯ ¯ - 02 ¯ ¯ - 03 ¯ ¯ - 04 ¯ ¯ - 05 ¯ ¯ ¯ - 06 ¯ ¯ ¯ - 07 ¯ ¯ ¯ - 08 ¯ ¯ - 09 ¯ ¯ - 10 ¯ ¯ - 11 ¯ ¯ - 12 ¯ ¯ - 13 ¯ ¯ - 14 ¯ ¯ - 15 ¯ ¯ - 16 ¯ ¯ - 17 ¯ ¯ - 18 ¯ ¯ - 19 ¯ ¯ ¯ ¯ ¯ - 20 ¯ ¯ ¯ ¯ ¯ - 21 ¯ ¯ ¯ ¯ - 22 ¯ ¯ ¯ ¯ - 23 ¯ ¯ ¯ - 24 ¯ ¯ ¯ ¯ ¯ - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -





IMC 0361BEDG



INSTALLATION MATERIALS Sheet 1/6

INSTALLATION MATERIALS Standard for 2Mbit/s 75 Ohm (Sub-D) Tributary

8xE1 16xE1 P/N Description See Sheet 1+0 1+0 1+1

Note

Connection Kits

597-525/16 IDU Connection Kit-Basic 4 1 1 1

Cable

103-037/50 YE-GR PVC 1x16mm² Grounding Cable - 5m 5m 10m b

105-013/02 2x1,5mm² Bipolar Shielded Cable - 5m 5m 5m b

Tributary Assembled Cable (Preferred) a

314-331/35 or

8xE1 75 Ohm Tributary Cable L=5m

314-331/36 or


314-331/37 or


314-331/38 8xE1 75 Ohm Tributary Cable L=30m

- 1 2 2

Tributary NO-Assembled Cable (On Request) a

332-055/57 Tributary Connection Kit 4 1 2 2

104-102/23 16 Coaxial Cable - 5m 10m 10m b

Tributary with D.D.F. and Assembled Cable (On Request) a

232-334/86 Mechanical Support Frame – 75 Ohm (up to 6 8xE1 or 3 16xE1) - 1 1 1

332-055/41 8xE1 (75 Ohm)Tributary Cable Kit - 1 - -

332-055/42 16xE1 (75 Ohm) Tributary Cable Kit - - 1 1

IN/OUT Connections

104-009/5.. Braided 50 Ohm Coaxial Cable 5 20m 20m 40m b

597-525/59 Braided Coaxial Cable Accessories 5 1 1 2 a) = In alternative one each other b) = Unless otherwise specified, the reported values are suggested lengths; the cables are supplied on reels.





IMC 0361BEDG



INSTALLATION MATERIALS Sheet 2

INSTALLATION MATERIALS Standard for 2Mbit/s 120 Ohm (Sub-D) Tributary

8xE1 16xE1 P/N Description See Sheet 1+0 1+0 1+1

Note

Connection Kits

597-525/16 IDU Connection Kit-Basic 4 1 1 1

Cable

103-037/50 YE-GR PVC 1x16mm² Grounding Cable - 5m 5m 10m b

105-013/02 2x1,5mm² Bipolar Shielded Cable - 5m 5m 5m b

Tributary Assembled Cable (Preferred) a

314-331/79 or 8xE1 120 Ohm Tributary Cable L=5m



314-331/82 8xE1 120 Ohm Tributary Cable L=30m

- 1 2 2

Tributary NO-Assembled Cable (On Request) a

332-055/57 Tributary Connection Kit 4 1 2 2

106-041/25 16 Pairs Double Shield Cable - 5m 10m 10m b

Tributary with D.D.F. and Assembled Cable (On Request) a

232-334/92 Mechanical Support Frame – 120 Ohm (up to 8 8xE1 or 4 16xE1) - 1 1 1

314-332/54 8xE1 (120 Ohm) Tributary Cable - 1 2 2

IN/OUT Connections

104-009/5.. Braided 50 Ohm Coaxial Cable 5 20m 20m 40m b

597-525/59 Braided Coaxial Cable Accessories 5 1 1 2 a) = In alternative one each other b) = Unless otherwise specified, the reported values are suggested lengths; the cables are supplied on reels.





IMC 0361BEDG




INSTALLATION MATERIALS Optional

Alarm Connection

P/N Description Q.ty Note 422-053/63 Alarms Connector 1 106-041/12 4 Pairs Double Shield Cable 5m

if Alarms connection is required

Data Channels Connections

P/N Description Q.ty Note 422-053/63 User/Dext Connector 2 106-041/12 4 Pairs Double Shield Cable 5m

if User/Dext connection is required

Interconnection Cable 1 Dext-Dext SRAL Compatible Connection

LAN Connection

P/N Description Q.ty / Note

314-324/54 Cable of Cross Screened q.ty n-1 (n=IDU equipment of daisy chain) 422-053/63 LAN Connector 106-041/76 LAN Cable (cat. 5)

for each LAN connection q.ty to be define

F Interworking – S Channel Connection

P/N Description Q.ty Note

314-332/48 Interconnection Cable 1 F Interworking – S Channel Connection





IMC 0361BEDG




INSTALLATION MATERIALS Compositions

IDU Connection Kit-Basic 597-525/16

ITEM P/N DESCRIPTION Q.ty

1 332-055/28 Power Supply Accessories 1 1.1 422-060/16 DM Connector 3s AP 1 1.2 422-027/31 HP Female Contact 2 1.3 422-030/82 45° Metallic Shell for Sub-D 15c 1

2 314-303/56 Ground Cable 1 3 314-205/76 Installation Kit 1

3.1 223-009/16 Cable tie for internal L=280mm (1.7÷77) 20 3.2 215-031/70 Uninsulated tube term. Ø6.4 for 16mm² cable 5 3.3 203-343/15D Stainless steel screw M6x22 3 3.4 207-510/11D Stainless steel washer Ø6 3 3.5 207-501/11D Stainless steel spring washer Ø6 3 3.6 206-702/14D Stainless steel hex nut Ø6 3 3.7 223-009/27 Cable tie for external L=508mm (74÷140) 5

4 216-42/102 Metal Label 2 5 216-42/103 Metal Label 2

Tributary Connection Kit 332-055/57


1 422-062/89 Sub-D Connector 50c S 1 2 422-058/81 50° Metallic Shell for Sub-D 50c 1 3 422-059/16 Locking screw 2





IMC 0361BEDG




INSTALLATION MATERIALS Compositions

IN/OUT 50 Ohm BRAIDED COAXIAL CABLE and ACCESSORIES ANDREW set (a)


1 104-009/50 314-331/88 (b) CNT300 - 50 Ohm BRAIDED COAXIAL CABLE (c)

2 597-525/59A 597-525/59 (b) BRAIDED COAXIAL CABLE ACCESSORIES (d)

2.1 421-025/30 90° COAXIAL SMA-PLUG 1

2.2 421-008/35 90° COAXIAL N-PLUG 1

2.3 333-031/21 GROUNDING KIT 1

IN/OUT 50 Ohm BRAIDED COAXIAL CABLE and ACCESSORIES INTERCOND set (a)


1 104-009/51 314-331/88 (b) INC48 - 50 Ohm BRAIDED COAXIAL CABLE (c)

2 597-525/59B 597-525/59 (b) BRAIDED COAX CABLE ACCESSORIES (d)

2.1 421-025/31 90° COAXIAL SMA-PLUG 1

2.2 421-008/36 90° COAXIAL N-PLUG 1

2.3 333-031/22 GROUNDING KIT 1

a = The ANDREW and INTERCOND material sets are alternative to each other

b = Commercial reference

c = The length of one IDU/ODU connection is 200 Mt. Max. for length up to 300m the 1/4" Coax Cable is available on request (refer to IMC 0258BEDG)

d = Q.ty 1 for each IDU/ODU connection





IMC 0361BEDG




INSTALLATION MATERIALS

REVISION LIST

Revisions Revisions Sheet

01 02 03 04 05 06 07 08 09 10 Sheet

01 02 03 04 05 06 07 08 09 10

01 ¯ ¯ - 02 ¯ ¯ - 03 ¯ ¯ - 04 ¯ ¯ - 05 ¯ ¯ - 06 ¯ ¯ - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -





IMC 0262BEDG

SRAL XD


INSTALLATION INFORMATION for SPECIAL TOOL Sheet 1 / 9

SPECIAL TOOLS USER TABLE

USE FOR CONNECTORS

Item Code Description

Power Supply Connector

(422-060/16, 422-027/31)

Coaxial Plug (421-015/60)

RJ45 Connector

(422-053/63)

Braided coaxial cable

(104-009/50-51)

DDF W-W 120 Ohm

(232-334/92, 314-332/32)

See Sheet

1. 323-003/19 Crimping tool

P.I./S.B./ S.B.2 - - - - 2

2. 236-100/40 Crimping tool - P.I./M.I. - - - 3

3. 236-100/17 Crimping tool - - P.I./S.B./

S.B.2 - - 4

4. 236-100/39 Cable

stripping tool

- - - P.I./S.B./ S.B.2/M.I. - 5

5. 236-100/50 Strap Plier - - - P.I./S.B./ S.B.2/M.I. - 6

6. 236-100/54 Wire cut and strip

tool - - - - P.I./S.B./

S.B.2 7

7. 236-100/55 Hand

wrapping tool

- - - - P.I./S.B./ S.B.2 8

P.I. = SRAL XD PLUG-IN S.B. = SRAL XD SINGLE BOARD S.B.2 = SRAL XD SINGLE BOARD 2 M.I. = SRAL XD MINIDU



LOW CAPACITY DIGITAL RADIO SYSTEMINSTALLATION INFORMATION for SPECIAL TOOL

SRAL XD

CMO-GS-NI-SE

A. Vergani

Dept.:

Exec.:

Date:

Check:

12-05-2003

M. Brambilla

IMC 0262BEDG

Sheet 2

Name:

Name:

Var.:

Emiss.:

Ed.:


SHIELDED CABLE (105-013/02).

* WARNING * = ONE TOOL FOR EACH INSTALLATION TEAM HAS TO BE SUPPLIED

The CRIMP TOOL is used for crimping the POWER SUPPLY CONNECTOR to the 2x1.5 mm² BIPOLAR

forCRIMPING TOOL (323-003/19)

SPECIAL TOOL

POWER SUPPLY CONNECTOR(422-060/16, 422-027/31)

THE SPECIAL TOOL CONSISTS OF ONE CRIMP TOOL AND TWO MATRIX

CRIMP TOOL (M309)

(422-027/35)for MALE CONTACTMATRIX (TP1075)

(422-027/31)for FEMALE CONTACT

MATRIX (TP1073)

06 06-07 A. Vergani




SRAL XD

CMO-GS-NI-SE

A. Vergani

Dept.:

Exec.:

Date:

Check:

12-05-2003

M. Brambilla

IMC 0262BEDG

Sheet 3

Name:

Name:

Var.:

Emiss.:

Ed.:


SPECIAL TOOLCRIMPING TOOL (236-100/40)

for COAXIAL PLUG (421-015/60)

to the COAXIAL CABLE (104-102/22-23)

The CRIMP TOOL is used for crimping the COAXIAL PLUG (421-015/60),

CRIMP TOOL (DCC CM 194)236-100/40

* WARNING * = ONE CRIMPING TOOL HAS TO BE SUPPLIED FOR EACH INSTALLATION TEAM

06 06-07 A. Vergani




SRAL XD

CMO-GS-NI-SE

A. Vergani

Dept.:

Exec.:

Date:

Check:

12-05-2003

M. Brambilla

IMC 0262BEDG

Sheet 4


forCRIMPING TOOL (236-100/17)

SPECIAL TOOL

RJ45 CONNECTOR(422-053/63)

CRIMPING TOOL

for

The CRIMPING TOOL is used for crimping the RJ45 SHIELDED CONNECTOR ON THE

* WARNING * = ONE TOOL HAS TO BE SUPPLIED IF THE LAN CONNECTION IS REQUIRED

Lan Cable (106-041/76)

(Cod. MISCO A1287)





SRAL XD

CMO-GS-NI-SE

A. Vergani

Dept.:

Exec.:

Date:

Check:

12-05-2003

M. Brambilla

IMC 0262BEDG

Sheet 5

Name:

Name:

Var.:

Emiss.:

Ed.:


(333-031/21-22)

(Cod. BETA UTENSILI 1144)

* WARNING * = ONE TOOL HAS TO BE SUPPLIED FOR EACH INSTALLATION TEAM

forCABLE STRIPPING TOOL (236-100/39)

SPECIAL TOOLS

GROUNDING KIT

CABLE STRIPPING TOOL

06 06-07 A. Vergani




SRAL XD

CMO-GS-NI-SE

A. Vergani

Dept.:

Exec.:

Date:

Check:

29-03-2004

M. Brambilla

IMC 0262BEDG

Sheet 6


STRAP PLIER (236-100/50)

SPECIAL TOOL

STRAP PLIER (236-100/50)

* WARNING * = ONE TOOL HAS TO BE SUPPLIED IF THE LAN CONNECTION IS REQUIRED

Model for nylon straps up to 9 mm wide- Blade to cut projecting lengths- Body in pressed sheet steel- Enamelled finish





SRAL XD

CMO-GS-NI-SE

A. Vergani

Dept.:

Exec.:

Date:

Check:

29-03-2004

M. Brambilla

IMC 0262BEDG

Sheet 7

Name:

Name:

Var.:

Emiss.:

Ed.:


WIRE CUT and STRIP TOOL (236-100/54)

SPECIAL TOOL

WIRE CUT and STRIP TOOL (ST-100-24)


06 06-07 A. Vergani

(232-334/92, 314-332/32)120 Ohm Wire-Wrap D.D.F.

for

on the 120 Ohm Wire-Wrap D.D.F. (232-334/92, 314-332/32)The TOOL is used for CUT and STRIP the 120 Ohm MULTIPAIRS DOUBLE SHIELDED CABLE Ø 0.5 mm

236-100/54




SRAL XD

CMO-GS-NI-SE

A. Vergani

Dept.:

Exec.:

Date:

Check:

4-10-2004

M. Brambilla

IMC 0262BEDG

Sheet 8


HAND WRAPPING TOOL (236-100/55)

SPECIAL TOOL

HAND WRAPPING and UNWRAPPING TOOL (HW-UW-2426)


(232-334/92, 314-332/32)120 Ohm Wire-Wrap D.D.F.

for

SHIELDED CABLE on the 120 Ohm Wire-Wrap D.D.F. (232-334/92, 314-332/32)The HAND TOOL is used for WRAPPING and UNWRAPPING the 120 Ohm MULTIPAIRS DOUBLE

236-100/55






IMC 0262BEDG

SRAL XD


INSTALLATION INFORMATION for SPECIAL TOOL Sheet 9

SPECIAL TOOL

REVISION LIST


Sheet 01 02 03 04 05 06 07 08 09 10

01 ¯ ¯ ¯ ¯ ¯ ¯ - 02 ¯ ¯ - 03 ¯ ¯ ¯ ¯ - 04 ¯ ¯ - 05 ¯ ¯ ¯ ¯ - 06 ¯ ¯ - 07 ¯ ¯ ¯ - 08 ¯ ¯ - 09 ¯ ¯ ¯ - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -



Documents

Code: Equipment: Title: