706
CNC 8055 Installation manual Ref. 1110 Soft: V01.3x

CNC 8055 - Installation manual...5.2 Analog inputs and outputs ..... 132 5.3 Setup..... 133 5.4 Connection of the CHAPTER 6 MACHINE PARAMETERS 6.1 Parameters that may be modified from

  • Upload
    others

  • View
    11

  • Download
    0

Embed Size (px)

Citation preview

  • CNC 8055

    Installation manual

    Ref. 1110Soft: V01.3x

  • This product uses the following source code, subject to the terms of the GPL license. The applications busybox V0.60.2;dosfstools V2.9; linux-ftpd V0.17; ppp V2.4.0; utelnet V0.1.1. The librarygrx V2.4.4. The linux kernel V2.4.4. The linux bootppcboot V1.1.3. If you would like to have a CD copy of this source code sent to you, send 10 Euros to Fagor Automationfor shipping and handling.

    All rights reserved. No part of this documentation may be transmitted,transcribed, stored in a backup device or translated into another languagewithout Fagor Automation’s consent. Unauthorized copying or distributing of thissoftware is prohibited.

    The information described in this manual may be changed due to technicalmodifications. Fagor Automation reserves the right to make any changes to thecontents of this manual without prior notice.

    All the trade marks appearing in the manual belong to the corresponding owners.The use of these marks by third parties for their own purpose could violate therights of the owners.

    It is possible that CNC can execute more functions than those described in itsassociated documentation; however, Fagor Automation does not guarantee thevalidity of those applications. Therefore, except under the express permissionfrom Fagor Automation, any CNC application that is not described in thedocumentation must be considered as "impossible". In any case, FagorAutomation shall not be held responsible for any personal injuries or physicaldamage caused or suffered by the CNC if it is used in any way other than asexplained in the related documentation.

    The content of this manual and its validity for the product described here has beenverified. Even so, involuntary errors are possible, thus no absolute match isguaranteed. Anyway, the contents of the manual is periodically checked makingand including the necessary corrections in a future edition. We appreciate yoursuggestions for improvement.

    The examples described in this manual are for learning purposes. Before usingthem in industrial applications, they must be properly adapted making sure thatthe safety regulations are fully met.

  • Installation manual

    CNC 8055CNC 8055i

    SOFT: V01.3X

    ·3·

    I N D E X

    About the product ......................................................................................................................... 9Declaration of conformity ............................................................................................................ 11Version history ............................................................................................................................ 13Safety conditions ........................................................................................................................ 15Warranty terms ........................................................................................................................... 19Material returning terms.............................................................................................................. 21Additional remarks ...................................................................................................................... 23Fagor documentation.................................................................................................................. 25

    CHAPTER 1 8055 CNC CONFIGURATION

    1.1 CNC structure ................................................................................................................ 271.2 Central unit..................................................................................................................... 291.2.1 –CPU– Module........................................................................................................... 331.2.2 –Vpp Axes– module ................................................................................................... 431.2.3 –Vpp SB Axes– module ............................................................................................. 501.2.4 –I/O– module (inputs - outputs).................................................................................. 571.3 Monitors ......................................................................................................................... 621.3.1 11" LCD Monitor......................................................................................................... 631.3.2 11" LCD monitor + M, T, MC or TC keyboard ............................................................ 651.4 Operator panel ............................................................................................................... 671.4.1 MC, TC, MCO/TCO and alphanumeric operator panels ............................................ 681.4.2 Alphanumeric keyboard (optional) ............................................................................. 69

    CHAPTER 2 8055I CNC CONFIGURATION

    2.1 CNC structure ................................................................................................................ 732.1.1 Connectors................................................................................................................. 772.2 Operator panel ............................................................................................................. 1022.2.1 Alphanumeric keyboard (optional) ........................................................................... 104

    CHAPTER 3 HEAT DISSIPATION

    3.1 Heat dissipation by natural convection ........................................................................ 1083.2 Heat dissipation by forced convection with inside fan.................................................. 1093.3 Heat dissipation by air flow to the outside using a fan ................................................. 110

    CHAPTER 4 REMOTE MODULES (BUS CAN WITH CANOPEN PROTOCOL)

    4.1 Installation of the modules ........................................................................................... 1134.2 Power supply ............................................................................................................... 1144.3 Digital inputs and digital outputs (single module)......................................................... 1204.4 Digital inputs and digital outputs (double module) ....................................................... 1224.5 Electrical characteristics of the inputs and outputs ...................................................... 1244.6 Numbering of the digital inputs and outputs................................................................. 126

    CHAPTER 5 MACHINE AND POWER CONNECTION

    5.1 Digital inputs and outputs............................................................................................. 1315.2 Analog inputs and outputs ........................................................................................... 1325.3 Setup............................................................................................................................ 1335.4 Connection of the emergency input and output ........................................................... 137

    CHAPTER 6 MACHINE PARAMETERS

    6.1 Parameters that may be modified from the oscilloscope, OEM program or OEM subroutine145

    6.2 General machine parameters ...................................................................................... 1476.3 Axis parameters .......................................................................................................... 2056.4 Spindle parameters...................................................................................................... 2376.4.1 Machine parameters for the main and 2nd spindles ................................................ 2386.4.2 Machine parameters for auxiliary spindle................................................................. 2576.5 Drive parameters ......................................................................................................... 2596.5.1 Friction compensation .............................................................................................. 2626.6 Serial line parameters .................................................................................................. 263

  • ·4·

    Installation manual

    CNC 8055CNC 8055i

    SOFT: V01.3X

    6.7 Ethernet parameters .................................................................................................... 2666.7.1 On an 8055 CNC without Ethernet connector at the –CPU– module. ..................... 2666.7.2 On an 8055i CNC or 8055 CNC with Ethernet connector at the –CPU– module. ... 2696.8 PLC Parameters ......................................................................................................... 2736.9 Tables ......................................................................................................................... 2816.9.1 Miscellaneous (M) function table ............................................................................. 2816.9.2 Leadscrew error compensation table....................................................................... 2836.9.3 Cross compensation parameter table ...................................................................... 285

    CHAPTER 7 CONCEPTS

    7.1 Axes and coordinate systems...................................................................................... 2877.1.1 Rotary axes.............................................................................................................. 2907.1.2 Gantry axes.............................................................................................................. 2927.1.3 Slaved axes and synchronized axes........................................................................ 2937.1.4 Incline axis ............................................................................................................... 2947.1.5 Tandem axes ........................................................................................................... 2967.2 Jog ............................................................................................................................... 3027.2.1 Relationship between the axes and the JOG keys .................................................. 3027.2.2 Path-jog mode.......................................................................................................... 3037.3 Movement with an electronic handwheel .................................................................... 3057.3.1 Standard handwheel ................................................................................................ 3067.3.2 Path handwheel ....................................................................................................... 3077.3.3 Feed handwheel mode ............................................................................................ 3087.3.4 "Additive handwheel" mode ..................................................................................... 3097.4 feedback system.......................................................................................................... 3117.4.1 Counting speed limitation......................................................................................... 3127.4.2 Resolution ................................................................................................................ 3137.5 Axis adjustment ........................................................................................................... 3177.5.1 Drive setting ............................................................................................................. 3187.5.2 Gain setting.............................................................................................................. 3197.5.3 Proportional gain setting .......................................................................................... 3207.5.4 Feed-forward gain setting ........................................................................................ 3217.5.5 Derivative (AC-forward) gain setting ........................................................................ 3227.5.6 Leadscrew backlash compensation. ........................................................................ 3237.5.7 Leadscrew error compensation................................................................................ 3247.5.8 Circle geometry test ................................................................................................. 3267.6 Reference systems ...................................................................................................... 3287.6.1 Home search............................................................................................................ 3297.6.2 Setting on systems without distance-coded feedback ............................................. 3337.6.3 Setting on systems with distance-coded feedback .................................................. 3357.6.4 Axis travel limits (software limits) ............................................................................. 3367.7 Unidirectional approach ............................................................................................... 3377.8 Auxiliary M, S, T function transfer ................................................................................ 3387.8.1 Transferring M, S, T using the AUXEND signal ....................................................... 3407.8.2 Transferring the auxiliary (miscellaneous) M functions without the AUXEND signal 3417.9 Main and second spindle ............................................................................................. 3427.9.1 Spindle types ........................................................................................................... 3447.9.2 Spindle speed (S) control......................................................................................... 3457.9.3 Spindle gear change ................................................................................................ 3477.9.4 Spindle in closed loop .............................................................................................. 3497.10 Auxiliary spindle controlled by PLC ............................................................................. 3557.11 Treatment of emergency signals ................................................................................. 3567.12 Digital servo (CAN or Sercos)...................................................................................... 3597.12.1 Communications channel......................................................................................... 3607.12.2 Drive’s absolute feedback........................................................................................ 3637.13 Axes (2) controlled by a single drive........................................................................... 3647.13.1 "C" axis and spindle with a single feedback............................................................. 3677.14 Additive coupling between axes .................................................................................. 3707.15 Fagor handwheels: HBA, HBE and LGB .................................................................... 3727.16 Machine safety related functions ................................................................................. 3767.16.1 Maximum machining spindle speed......................................................................... 3767.16.2 Cycle start disabled when hardware errors occur. ................................................... 3777.17 Configuring a CNC as two and a half axes.................................................................. 3787.17.1 Machine parameter setting ...................................................................................... 3797.17.2 PLC program............................................................................................................ 3807.18 Tool magazine ............................................................................................................. 3827.18.1 Tool change via PLC................................................................................................ 3827.18.2 Tool change management ....................................................................................... 383

  • Installation manual

    CNC 8055CNC 8055i

    SOFT: V01.3X

    ·5·

    7.19 Gear ratio management on axes and spindle .............................................................. 3847.19.1 Example of axes: outside feedback without gear box .............................................. 3857.19.2 Example of axes: encoder at the motor ................................................................... 3897.19.3 Example of axes: outside feedback with gear box ................................................... 3907.19.4 Example of spindle: external encoder without gear box........................................... 3937.19.5 Example of spindle: encoder at the motor................................................................ 3967.19.6 Example of spindle: external encoder with gear box................................................ 3987.20 Feedback combination for SERCOS axes with external feedback to the CNC ........... 4017.21 Open communication ................................................................................................... 4027.21.1 Reception setting ..................................................................................................... 4047.21.2 Incompatibility with WINDNC via RS232.................................................................. 4047.21.3 Trace of characters sent and received..................................................................... 4057.21.4 Examples of open communication ........................................................................... 406

    CHAPTER 8 INTRODUCTION TO THE PLC

    8.1 PLC resources ............................................................................................................. 4128.2 PLC program execution ............................................................................................... 4138.3 Loop time ..................................................................................................................... 4168.4 Modular structure of the program................................................................................. 4178.4.1 First cycle module (CY1).......................................................................................... 4178.4.2 Main module (PRG) ................................................................................................. 4178.4.3 Periodic execution module (PE t)............................................................................. 4188.4.4 Priority of execution of the PLC modules ................................................................. 419

    CHAPTER 9 PLC RESOURCES

    9.1 Inputs ........................................................................................................................... 4219.2 Outputs ........................................................................................................................ 4229.3 Marks ........................................................................................................................... 4239.4 Registers...................................................................................................................... 4259.5 Timers .......................................................................................................................... 4269.5.1 Monostable mode. TG1 input................................................................................... 4299.5.2 Delayed activation mode. TG2 input ........................................................................ 4319.5.3 Delayed deactivation mode. TG3 input .................................................................... 4339.5.4 Signal limiting mode. TG4 Input ............................................................................... 4359.6 Counters ...................................................................................................................... 4379.6.1 Operating mode of a counter ................................................................................... 440

    CHAPTER 10 PLC PROGRAMMING

    10.1 Module structure .......................................................................................................... 44210.2 Directing instructions.................................................................................................... 44310.3 Consulting instructions................................................................................................. 44610.4 Operators and symbols................................................................................................ 44810.5 Action instruction.......................................................................................................... 44910.5.1 Binary assignment instructions ................................................................................ 45010.5.2 Conditional binary action instructions....................................................................... 45110.5.3 Sequence breaking action instructions .................................................................... 45210.5.4 Arithmetic action instructions ................................................................................... 45310.5.5 Logic action instructions........................................................................................... 45510.5.6 Specific action instructions....................................................................................... 457

    CHAPTER 11 CNC-PLC COMMUNICATION

    11.1 Auxiliary M, S, T functions ........................................................................................... 46011.2 Auxiliary M, S, T function transfer ................................................................................ 46311.2.1 Transferring M, S, T using the AUXEND signal ....................................................... 46411.2.2 Transferring the auxiliary (miscellaneous) M functions without the AUXEND signal 46511.3 Displaying messages, errors and screens ................................................................... 46611.4 Access to the PLC from the CNC ................................................................................ 46811.5 Access to the PLC from a PC, via DNC....................................................................... 469

  • ·6·

    Installation manual

    CNC 8055CNC 8055i

    SOFT: V01.3X

    CHAPTER 12 LOGIC CNC INPUTS AND OUTPUTS

    12.1 General logic inputs ..................................................................................................... 47212.2 Axis logic inputs. .......................................................................................................... 48112.3 Spindle logic inputs. ..................................................................................................... 48612.4 Logic inputs of the auxiliary spindle ............................................................................. 49112.5 Key inhibiting logic inputs. ........................................................................................... 49212.6 Logic inputs of the PLC channel .................................................................................. 49312.7 General logic outputs................................................................................................... 49512.8 Logic outputs of the axes............................................................................................. 50212.9 Spindle logic outputs.................................................................................................... 50412.10 Logic outputs of the auxiliary spindle........................................................................... 50612.11 Logic outputs of key status .......................................................................................... 507

    CHAPTER 13 ACCESS TO INTERNAL CNC VARIABLES

    13.1 Variables associated with tools.................................................................................... 51113.2 Variables associated with zero offsets......................................................................... 51513.3 Variables associated with function G49....................................................................... 51613.4 Variables associated with machine parameters .......................................................... 51813.5 Variables associated with work zones ......................................................................... 51913.6 Variables associated with feedrates ............................................................................ 52113.7 Variables associated with coordinates......................................................................... 52413.8 Variables associated with electronic handwheels........................................................ 52613.9 Variables associated with feedback............................................................................. 52813.10 Variables associated with the main spindle ................................................................. 52913.11 Variables associated with the second spindle ............................................................. 53213.12 Variables associated with the live tool ......................................................................... 53513.13 Variables associated with local and global parameters ............................................... 53613.14 Sercos variables .......................................................................................................... 53713.15 Software & hardware configuration variables .............................................................. 53813.16 Variables associated with telediagnosis ...................................................................... 54113.17 Operating-mode related variables ............................................................................... 54313.18 Other variables ............................................................................................................ 546

    CHAPTER 14 AXES CONTROLLED FROM THE PLC

    14.1 PLC execution channel ................................................................................................ 55814.1.1 Considerations ......................................................................................................... 55914.1.2 Blocks which can be executed from the PLC........................................................... 56114.1.3 Control of the PLC program from the CNC .............................................................. 56514.2 Action CNCEX1 ........................................................................................................... 56714.3 Synchronize a PLC axis with a CNC axis .................................................................... 568

    CHAPTER 15 CUSTOMIZABLE SCREENS

    15.1 Configuration file.......................................................................................................... 57015.2 Configuration language................................................................................................ 57215.3 Key words .................................................................................................................... 57315.4 Arithmetic operations ................................................................................................... 57715.5 Conditional instructions................................................................................................ 57915.6 Example of a configuration file..................................................................................... 58015.7 Error log file (P999500)................................................................................................ 582

    CHAPTER 16 CONFIGURABLE WORK MODE

    16.1 Axis control .................................................................................................................. 58516.2 Tool control .................................................................................................................. 58616.3 Spindle control ............................................................................................................. 58716.4 MDI .............................................................................................................................. 58816.5 Screens, subroutines and cycles ................................................................................. 58916.6 Associated keys........................................................................................................... 59016.7 OEM text in several languages.................................................................................... 59216.8 Associated programs ................................................................................................... 59516.9 Associated subroutines................................................................................................ 59616.10 Configuration file.......................................................................................................... 59716.11 Error log file (P999500)................................................................................................ 60116.12 Cycle data entry........................................................................................................... 60216.13 Example. Consult inputs and outputs .......................................................................... 60416.14 Example. Machining canned cycle .............................................................................. 605

  • Installation manual

    CNC 8055CNC 8055i

    SOFT: V01.3X

    ·7·

    CHAPTER 17 PLC PROGRAMMING EXAMPLE

    17.1 Definition of symbols (mnemonics) .............................................................................. 60817.2 First cycle module. ....................................................................................................... 61017.3 Main module. ............................................................................................................... 611

    APPENDIX

    A Technical characteristics of the 8055i CNC ................................................................. 621B Central unit of the 8055 CNC....................................................................................... 625C 11" LCD Monitor........................................................................................................... 629D Probe connection at the 8055i ..................................................................................... 631E Probe connection at the 8055 CNC ............................................................................. 633F Summary of internal CNC variables............................................................................. 635G Summary of PLC commands ....................................................................................... 643H Summary of PLC inputs and outputs ........................................................................... 647I 2-digit BCD code output conversion table.................................................................... 653J Key codes .................................................................................................................... 655K Logic outputs of key status .......................................................................................... 665L Key inhibiting codes ..................................................................................................... 675M Machine parameter setting chart ................................................................................. 685N M functions setting chart .............................................................................................. 697O Leadscrew error compensation table........................................................................... 699P Cross compensation table ........................................................................................... 701Q Maintenance ................................................................................................................ 703

  • ·8·

    Installation manual

    CNC 8055CNC 8055i

    SOFT: V01.3X

  • CNC 8055CNC 8055i

    ·9·

    ABOUT THE PRODUCT

    BASIC CHARACTERISTICS OF THE DIFFERENT MODELS.

    HARDWARE OPTIONS OF THE 8055I CNC

    8055 FL8055i FL

    8055i FL EN

    8055 Power8055i Power

    Built-in 8055i FL8055i FL EN

    8055i Power

    Enclosure 8055 FL 8055 Power

    USB Standard Standard

    Block processing time 3,5 ms 0,9 ms

    RAM memory 1Mb 1 Mb

    Software for 7 axes ----- Option

    TCP transformation ----- Option

    C axis (Lathe) ----- Option

    Y axis (Lathe) ----- Option

    Look-ahead 100 blocks 200 blocks

    512Mb / 2Gb flash memory Option512Mb on the EN model

    Option

    Analog Digital Engraving

    Ethernet Option Option Option

    RS-232 serial line Standard Standard Standard

    16 digital inputs and 8 outputs (I1 to I16 and O1 to O8) Standard Standard Standard

    Another 40 digital inputs and 24 outputs (I65 to I104 and O33 to O56) Option Option Option

    Probe inputs Standard Standard Standard

    Spindle (feedback input and analog output) Standard Standard Standard

    Electronic handwheels Standard Standard Standard

    4 axes (feedback and velocity command) Option Option - - -

    Remote CAN modules, for digital I/O expansion (RIO). Option Option - - -

    Sercos servo drive system for Fagor servo drive connection. - - - Option - - -

    CAN servo drive system for Fagor servo drive connection. - - - Option - - -

    Before start-up, verify that the machine that integrates this CNC meets the 89/392/CEE Directive.

  • ·10·

    CNC 8055CNC 8055i

    Abo

    ut th

    e pr

    oduc

    t

    SOFTWARE OPTIONS OF THE 8055 CNC AND 8055I CNC

    Model

    GP M MC MCO EN T TC TCO

    Number of axes with standard software 4 4 4 4 3 2 2 2

    Number of axes with optional software 7 7 7 7 ----- 4 or 7 4 or 7 4 or 7

    Electronic threading ----- Stand Stand Stand Stand Stand Stand Stand

    Tool magazine management: ----- Stand Stand Stand ----- Stand Stand Stand

    Machining canned cycles ----- Stand Stand ----- Stand Stand Stand -----

    Multiple machining ----- Stand Stand ----- Stand ----- ----- -----

    Solid graphics ----- Stand Stand Stand ----- Stand Stand Stand

    Rigid tapping ----- Stand Stand Stand Stand Stand Stand Stand

    Tool live monitoring ----- Opt Opt Opt Stand Opt Opt Opt

    Probing canned cycles ----- Opt Opt Opt Stand Opt Opt Opt

    DNC Stand Stand Stand Stand Stand Stand Stand Stand

    COCOM version Opt Opt Opt Opt ----- Opt Opt Opt

    Profile editor Stand Stand Stand Stand ----- Stand Stand Stand

    Tool radius compensation Stand Stand Stand Stand Stand Stand Stand Stand

    Tangential control Opt Opt Opt Opt ----- Opt Opt Opt

    Retracing ----- Opt Opt Opt Stand Opt Opt Opt

    Setup assistance Stand Stand Stand Stand Stand Stand Stand Stand

    Irregular pockets with islands ----- Stand Stand Stand ----- ----- ----- -----

    TCP transformation ----- Opt Opt Opt ----- ----- ----- -----

    C axis (on Lathe) ----- ----- ----- ----- ----- Opt Opt Opt

    Y axis (on Lathe) ----- ----- ----- ----- ----- Opt Opt Opt

    Telediagnosis Opt Opt Opt Opt Stand Opt Opt Opt

  • CNC 8055CNC 8055i

    ·11·

    DECLARATION OF CONFORMITY

    The manufacturer:

    Fagor Automation S. Coop.

    Barrio de San Andrés Nº 19, C.P. 20500, Mondragón -Guipúzcoa- (SPAIN).

    Declares:

    Under their responsibility that the product:

    NUMERICAL CONTROL 8055 / 8055i

    Consisting of the following modules and accessories:

    MONITOR-8055, MONITOR-55-11-USBOP-8055KS 50/55, KB-40/55-ALFA, DVD AMPLI 8055PSB-8055CPU-KEY CF 8055 FL LARGE, CPU-KEY CF 8055 Power LARGEAXES 8055 VPPI/O 8055, COVER 8055, SERCOS 8055Remote modules RIOCNC 8055i FL, CNC 8055i PowerANALOG 8055i-B, 40I/24O-8055i-B, ANALOG+40I/24O-B, COVER ANA+I/O-8055i-BETHERNET-CAN-SERCOS, ETHERNET-CAN-CAN AXES, ETHERNET-CAN AXES

    Note. Some additional characters may follow the references mentioned above. They all comply with the directiveslisted. However, check that that's the case by checking the label of the unit itself.

    Referred to by this declaration with following directives:

    As instructed by the European Community Directives 2006/95/EEC on Low Voltage and2004/108/EC on Electromagnetic Compatibility and its updates.

    In Mondragón, July 27th, 2010

    Low voltage regulations.

    EN 60204-1: 2006 Electrical equipment on machines — Part 1. General requirements.

    Regulation on electromagnetic compatibility.

    EN 61131-2: 2007 Programmable PLC's — Part 2. Unit requirements and tests.

  • CNC 8055CNC 8055i

    ·13·

    VERSION HISTORY

    Here is a list of the features added in each software version and the manuals that describe them.

    The version history uses the following abbreviations:

    INST Installation manual

    PRG Programming manual

    OPT Operating manual

    OPT-MC Operating manual for the MC option.

    OPT-TC Operating manual for the TC option.

    OPT-CO Manual of the CO manual

    Software V01.00 October 2010

    First version.

    Software V01.20 April 2011

    Software V01.08 August 2011

    Software V01.30 September 2011

    List of features Manual

    Open communication. INSTImprovements to Look Ahead machining. INST

    Blocks with helical interpolation in G51. PRG

    G84. Tapping with relief. PRG

    List of features Manual

    S.m.p. OPLDECTI (P86). INST

    List of features Manual

    Gear ratio management on Sercos spindles INSTImproved feedrate limit management (FLIMIT). INST

    New type of penetration in lathe type threading cycles. PRG

    Improved lathe type thread repair. Partial repair. PRG

    MC option: Rigid tapping with relief. OPT-MC

    TC option: New type of penetration in threading cycles. OPT-TC

    TC option: Improved thread repair. Partial and multi-entry (start) thread repair. OPT-TC

    TC option: Zig-zag entry to the groove at the starting point of the groove. OPT-TC

  • ·14·

    CNC 8055CNC 8055i

    Ver

    sion

    his

    tory

    Software V01.31 October 2011

    List of features Manual

    CNC 8055 FL Engraving model INST / OPT/ PRG

  • CNC 8055CNC 8055i

    ·15·

    SAFETY CONDITIONS

    Read the following safety measures in order to prevent harming people or damage to this product and thoseproducts connected to it.

    This unit may only be repaired by authorized personnel at Fagor Automation.

    Fagor Automation shall not be held responsible of any physical damage or defective unit resulting from notcomplying with these basic safety regulations.

    PRECAUTIONS AGAINST PERSONAL DAMAGE

    • Interconnection of modules.

    Use the connection cables provided with the unit.

    • Use proper Mains AC power cables

    To avoid risks, use only the Mains AC cables recommended for this unit.

    • Avoid electrical overloads.

    In order to avoid electrical discharges and fire hazards, do not apply electrical voltage outside the rangeselected on the rear panel of the central unit.

    • Ground connection.

    In order to avoid electrical discharges, connect the ground terminals of all the modules to the mainground terminal. Before connecting the inputs and outputs of this unit, make sure that all the groundingconnections are properly made.

    • Before powering the unit up, make sure that it is connected to ground.

    In order to avoid electrical discharges, make sure that all the grounding connections are properly made.

    • Do not work in humid environments.

    In order to avoid electrical discharges, always work under 90% of relative humidity (non-condensing)and 45 ºC (113º F).

    • Do not work in explosive environments.

    In order to avoid risks or damages, do no work in explosive environments.

  • ·16·

    CNC 8055CNC 8055i

    Saf

    ety

    cond

    ition

    s

    PRECAUTIONS AGAINST PRODUCT DAMAGE

    • Working environment.

    This unit is ready to be used in industrial environments complying with the directives and regulationseffective in the European Community.

    Fagor Automation shall not be held responsible for any damage suffered or caused when installed inother environments (residential or homes).

    • Install this unit in the proper place.

    It is recommended, whenever possible, to install the CNC away from coolants, chemical product, blows,etc. that could damage it.

    This unit complies with the European directives on electromagnetic compatibility. Nevertheless, it isrecommended to keep it away from sources of electromagnetic disturbance such as:

    Powerful loads connected to the same AC power line as this equipment.

    Nearby portable transmitters (Radio-telephones, Ham radio transmitters).

    Nearby radio/TV transmitters.

    Nearby arc welding machines.

    Nearby High Voltage power lines.

    Etc.

    • Enclosures.

    The manufacturer is responsible of assuring that the enclosure involving the equipment meets all thecurrently effective directives of the European Community.

    • Avoid disturbances coming from the machine tool.

    The machine-tool must have all the interference generating elements (relay coils, contactors, motors,etc.) uncoupled.

    DC relay coils. Diode type 1N4000.

    AC relay coils. RC connected as close to the coils as possible with approximate values of R=220 1 W and C=0,2 µF / 600 V.

    AC motors. RC connected between phases, with values of R=300 / 6 W and C=0,47 µF / 600 V.

    • Use the proper power supply.

    Use an external regulated 24 Vdc power supply for the inputs and outputs.

    • Grounding of the power supply.

    The zero volt point of the external power supply must be connected to the main ground point of themachine.

    • Analog inputs and outputs connection.

    It is recommended to connect them using shielded cables and connecting their shields (mesh) to thecorresponding pin.

    • Ambient conditions.

    The working temperature must be between +5 ºC and +40 ºC (41ºF and 104º F)

    The storage temperature must be between -25 ºC and +70 ºC. (-13 ºF and 158 ºF)

    • Monitor enclosure (8055) or central unit (8055i).

    Guarantee the required gaps between the monitor or the central unit and each wall of the enclosure.Use a DC fan to improve enclosure ventilation.

    • Power switch.

    This power switch must be mounted in such a way that it is easily accessed and at a distance between0.7 meters (27.5 inches) and 1.7 meters (5.5ft) off the floor.

  • CNC 8055CNC 8055i

    ·17·

    Saf

    ety

    cond

    ition

    s

    PROTECTIONS OF THE UNIT ITSELF (8055)

    • "Axes" and "Inputs/Outputs" modules.

    All the digital inputs and outputs have galvanic isolation via optocouplers between the CNC circuitryand the outside.

    They are protected by an external fast fuse (F) of 3.15 A 250V against overvoltage of the external powersupply (over 33 Vdc) and against reverse connection of the power supply.

    • Monitor.

    The type of protection fuse depends on the type of monitor. See identification label of the unit itself.

    PROTECTIONS OF THE UNIT ITSELF (8055I)

    • Central Unit.

    It has a 4 A 250V external fast fuse (F).

    • Inputs-Outputs.

    All the digital inputs and outputs have galvanic isolation via optocouplers between the CNC circuitryand the outside.

    OUT IN

    X7

    X1

    X8

    X9

    X2

    X10

    X3

    X11

    X4

    X12

    X5

    X13

    X6

    +24V0V

    FUSIBLEFUSE

  • ·18·

    CNC 8055CNC 8055i

    Saf

    ety

    cond

    ition

    s

    PRECAUTIONS DURING REPAIR

    SAFETY SYMBOLS

    • Symbols which may appear on the manual.

    Do not open this unit. Only personnel authorized by Fagor Automation may open this unit. Do not handle the connectors with the unit connected to mains. Before manipulating the connectors(inputs/outputs, feedback, etc.) make sure that the unit is not connected to AC power.

    Symbol for danger or prohibition.It indicates actions or operations that may cause damage to people or to units.

    Warning symbol.It indicates situations that may be caused by certain operations and the actions to be taken to preventthem.

    Obligation symbol.It indicates actions and operations that must be carried out.

    Information symbol.It indicates notes, warnings and advises.i

  • CNC 8055CNC 8055i

    ·19·

    WARRANTY TERMS

    INITIAL WARRANTY

    All products manufactured or marketed by FAGOR carry a 12-month warranty for the end user which couldbe controlled by the our service network by means of the warranty control system established by FAGORfor this purpose.

    In order to prevent the possibility of having the time period from the time a product leaves our warehouseuntil the end user actually receives it run against this 12-month warranty, FAGOR has set up a warrantycontrol system based on having the manufacturer or agent inform FAGOR of the destination, identificationand on-machine installation date, by filling out the document accompanying each FAGOR product in thewarranty envelope. This system, besides assuring a full year of warranty to the end user, enables our servicenetwork to know about FAGOR equipment coming from other countries into their area of responsibility.

    The warranty starting date will be the one appearing as the installation date on the above mentioneddocument. FAGOR offers the manufacturer or agent 12 months to sell and install the product. This meansthat the warranty starting date may be up to one year after the product has left our warehouse so long asthe warranty control sheet has been sent back to us. This translates into the extension of warranty periodto two years since the product left our warehouse. If this sheet has not been sent to us, the warranty periodends 15 months from when the product left our warehouse.

    This warranty covers all costs of material and labour involved in repairs at FAGOR carried out to correctmalfunctions in the equipment. FAGOR undertakes to repair or replace their products within the period fromthe moment manufacture begins until 8 years after the date on which it disappears from the catalogue.

    FAGOR has exclusive competence in deciding whether the repair enters within the term defined as thewarranty period.

    EXCLUDING CLAUSES

    Repairs will be carried out on our premises. Therefore, all expenses incurred as a result of trips made bytechnical personnel to carry out equipment repairs, despite these being within the above-mentioned periodof warranty, are not covered by the warranty.

    Said warranty will be applied whenever the equipment has been installed in accordance with instructions,has not be mistreated, has not been damaged by accident or by negligence and has not been tamperedwith by personnel not authorised by FAGOR. If, once servicing or repairs have been made, the cause ofthe malfunction cannot be attributed to said elements, the customer is obliged to cover the expensesincurred, in accordance with the tariffs in force.

    Other warranties, implicit or explicit, are not covered and FAGOR AUTOMATION cannot be held responsiblefor other damages which may occur.

  • ·20·

    CNC 8055CNC 8055i

    War

    rant

    y te

    rms

    WARRANTY ON REPAIRS

    In a similar way to the initial warranty, FAGOR offers a warranty on standard repairs according to thefollowing conditions:

    When the customer does not choose the standard repair and just the faulty material has been replaced,the warranty will cover just the replaced parts or components within 12 months.

    For sold parts the warranty is 12 moths length.

    MAINTENANCE CONTRACTS

    The SERVICE CONTRACT is available for the distributor or manufacturer who buys and installs our CNCsystems.

    PERIOD 12 months.

    CONCEPT Covers parts and labor for repairs (or replacements) at the network's ownfacilities.

    EXCLUDING CLAUSES The same as those applied regarding the chapter on initial warranty.If the repair is carried out within the warranty period, the warranty extensionhas no effect.

  • CNC 8055CNC 8055i

    ·21·

    MATERIAL RETURNING TERMS

    When sending the central nit or the remote modules, pack them in its original package and packagingmaterial. If the original packaging material is not available, pack it as follows:

    1. Get a cardboard box whose three inside dimensions are at least 15 cm (6 inches) larger than thoseof the unit. The cardboard being used to make the box must have a resistance of 170 kg. (375 pounds).

    2. Attach a label indicating the owner of the unit, person to contact, type of unit and serial number.

    3. In case of failure, also indicate the symptom and a short description.

    4. Wrap the unit in a polyethylene roll or similar material to protect it.

    5. When sending the central unit, protect especially the screen.

    6. Pad the unit inside the cardboard box with polyurethane foam on all sides.

    7. Seal the cardboard box with packing tape or industrial staples.

  • ·22·

    CNC 8055CNC 8055i

    Mat

    eria

    l ret

    urni

    ng te

    rms

  • CNC 8055CNC 8055i

    ·23·

    ADDITIONAL REMARKS

    Mount the CNC away from coolants, chemical products, blows, etc. which could damage it. Before turningthe unit on, verify that the ground connections have been properly made.

    To prevent electrical shock at the central unit of the 8055 CNC, use the proper mains AC connector at thepower supply module. Use 3-wire power cables (one for ground connection).

    To prevent electrical shock at the monitor of the 8055 CNC, use the proper mains AC connector (A) with3-wire power cables (one of them for ground connection).

    Before turning on the monitor of the 8055 CNC and verifying that the external AC line (B) fuse of each unitis the right one. See identification label of the unit itself.

    In case of a malfunction or failure, disconnect it and call the technical service. Do not get into the insideof the unit.

    FAGOR

    I/O

    X1

    X2

    X3

    AXES

    X1 X2

    X3 X4

    X5 X6

    X7 X8

    X9 X10

    CPU

    X1 X2

    CMPCTFLASH

    ETH

    COM1

    X3

    CDEF 0

    BA98 17 26 354

    IN

    OUT

    NODE

    USB

    (A)

    (B)

    X1

    W1

  • ·24·

    CNC 8055CNC 8055i

    Add

    ition

    al r

    emar

    ks

  • CNC 8055CNC 8055i

    ·25·

    FAGOR DOCUMENTATION

    OEM manual

    It is directed to the machine builder or person in charge of installing and starting-up the CNC.

    USER-M manual

    Directed to the end user.

    It describes how to operate and program in M mode.

    USER-T manual

    Directed to the end user.

    It describes how to operate and program in T mode.

    MC Manual

    Directed to the end user.

    It describes how to operate and program in MC mode.

    It contains a self-teaching manual.

    TC Manual

    Directed to the end user.

    It describes how to operate and program in TC mode.

    It contains a self-teaching manual.

    MCO/TCO model

    Directed to the end user.

    It describes how to operate and program in MCO and TCO mode.

    Examples-M manual

    Directed to the end user.

    It contains programming examples for the M mode.

    Examples-T manual

    Directed to the end user.

    It contains programming examples for the T mode.

    WINDNC Manual

    It is directed to people using the optional DNC communications software.

    It is supplied in a floppy disk with the application.

    WINDRAW55 manual

    Directed to people who use the WINDRAW55 to create screens.

    It is supplied in a floppy disk with the application.

  • ·26·

    CNC 8055CNC 8055i

    Fag

    or d

    ocum

    enta

    tion

  • CNC 8055CNC 8055i

    SOFT: V01.3X

    1

    ·27·

    8055 CNC CONFIGURATION

    The CNC is prepared to be used in industrial environments, especially on milling machines, lathes,etc.

    The CNC can control machine movements and devices.

    1.1 CNC structure

    The CNC consists of the following elements:

    • Central Unit.

    • Monitor.

    • Keyboard.

    The central unit (CPU) has a modular structure. There are 2 models: for 3 and 6 modules.

    Either separate keyboard and monitor or keyboards with an incorporated monitor are available.

    The monitors are 11" LCD.

    The keyboards are specific for each model and work mode.

    FAGOR

    I/O

    X1

    X2

    X3

    AXES

    X1 X2

    X3 X4

    X5 X6

    X7 X8

    X9 X10

    CPU

    X1 X2

    CMPCTFLASH

    ETH

    COM1

    X3

    CDEF 0

    BA98 17 26 354

    IN

    OUT

    NODE

    USB

    FAGOR

    I/O

    X1

    X2

    X3

    I/O

    X1

    X2

    X3

    I/O

    X1

    X2

    X3

    I/O

    X1

    X2

    X3

    AXES

    X1 X2

    X3 X4

    X5 X6

    X7 X8

    X9 X10

    CPU

    X1 X2

    CMPCTFLASH

    ETH

    COM1

    X3

    CDEF 0

    BA98 17 26 354

    IN

    OUT

    NODE

    USB

  • ·28·

    Installation manual

    CNC 8055CNC 8055i

    1.

    8055

    CN

    C C

    ON

    FIG

    UR

    AT

    ION

    SOFT: V01.3X

    CN

    C s

    truc

    ture

    The following illustration shows the possible combinations. Each configuration shows the value ofmachine parameter CUSTOMTY (P92).

    Use the video signal cable (up to 40 m) to connect the monitor with the central unit and the keyboardsignal cable (up to 25 m) to connect the keyboard with the central unit.

    Keyboard auto-identification

    Certain keyboard models have a auto-identification system. With this type of keyboards, parameterCUSTOMTY is updated automatically; for the rest of the keyboards, this parameter must be setmanually.

    If the keyboard does not match the CNC model, it shows the relevant error message and it loadsthe key codes that correspond to the CNC model. For example, if a mill model keyboard is connectedto a lathe CNC, the keyboard is set for a lathe and the CNC shows the error message.

    F AGOR

    I/O

    X1

    X2

    X3

    AXES

    X1 X2

    X3 X4

    X5 X6

    X7 X8

    X9 X10

    CPU

    X1 X2

    CMPCTFLASH

    ETH

    COM1

    X3

    CDE F0

    BA

    98 1

    7 26 35 4

    I N

    O UT

    N ODE

    USB

    F AGOR

    I/O

    X1

    X2

    X3

    I/O

    X1

    X2

    X3

    I/O

    X1

    X2

    X3

    I/O

    X1

    X2

    X3

    AXES

    X1 X2

    X3 X4

    X5 X6

    X7 X8

    X9 X10

    CPU

    X1 X2

    CMPCTFLASH

    ETH

    COM 1

    X3

    CDE F0

    BA9

    8

    17

    26

    35 4

    I N

    O UT

    N OD E

    USB

    FAGOR

    02410

    2030 40

    50 60 7080

    90100110120

    FEED %SPINDLEJOG

    10010

    11 10 100

    100010000

    8055-M11" LCD

    FAGOR

    02410

    2030

    40 50 60 7080

    90100110

    120

    FEED %SPINDLEJOG

    10010

    1 110 100

    100010000

    8055-MC11" LCD

    FAGOR

    02410

    2030 40

    50 60 7080

    90100110

    120

    FEED %SPINDLEJOG

    10010

    11 10 100

    100010000

    8055-T11" LCD

    FAGOR

    02410

    2030 40

    50 60 7080

    90100110

    120

    FEED %SPINDLEJOG

    10010

    11 10 100

    100010000

    8055-TC11" LCD

    MONITOR-55M-11-USB (CUSTOMTY=254)

    MONITOR-55MC-11-USB (CUSTOMTY=254)

    MONITOR-55T-11-USB (CUSTOMTY=254)

    MONITOR-55TC-11-USB (CUSTOMTY=254)

    FAGOR

    JOG

    10010

    1 110 1001000

    10000

    02410

    2030 40

    50 60 7080

    90100110120

    FEED %

    8055-MC

    FAGOR

    JOG

    10010

    1 110 100

    100010000

    02410

    2030 40

    50 6070

    8090100110

    120

    FEED %

    8055-M/T

    FAGOR

    JOG

    10010

    1 110 1001000

    10000

    02410

    2030 40

    50 60 7080

    90100110

    120

    FEED %

    8055-TC

    FAGOR

    JOG

    10010

    11 10 100

    100010000

    02410

    2030 40

    50 60 7080

    90100110

    120

    FEED %

    8055-MCO/TCO

    OP.8040/55.ALFA(CUSTOMTY=252)

    OP.8040/55MC(CUSTOMTY=0)

    OP.8040/55TC(CUSTOMTY=0)

    OP.8040/55MCO/TCO (CUSTOMTY=0)

    +

    + +FAGOR

    11" LCD

    MONITOR-8055 KB.40/55.ALFA

    + KS 50/55

    Option

  • Installation manual

    CNC 8055CNC 8055i

    8055

    CN

    C C

    ON

    FIG

    UR

    AT

    ION

    1.

    SOFT: V01.3X

    ·29·

    Cen

    tral

    uni

    t

    1.2 Central unit

    The central unit is usually located in the electrical cabinet, is modular and it comes in two models:There are 2 models: for 3 and 6 modules.

    The modules are mounted using the screws located at their top and bottom.

    Available modules

    CPU

    It contains the system software and carries out the CNC functions (editing, execution, simulation,display, etc.), process the information of the rest of the modules and generate the video signals forthe monitor.

    Optionally, it communicates with the drives via Sercos interface.

    It must be part of all the configurations and mounted as the first module from the left.

    Axes:

    Besides controlling the spindle and the axes of the machine, it governs the first 40 digital PLC inputsand 24 digital PLC outputs.

    It must be present in all configurations. Together with the –CPU– module makes up the basic systemconfiguration.

    I/Os

    It is optional. It offers another 64 digital PLC inputs and 32 digital PLC outputs.

    FAGOR

    I/O

    X1

    X2

    X3

    I/O

    X1

    X2

    X3

    I/O

    X2

    X3

    I/O

    X1

    X2

    X3

    AXES

    X1 X2

    X3 X4

    X5 X6

    X7 X8

    X9X10

    CPU

    X1 X2

    CMPCTFLASH

    ETH

    COM1

    X3

    CDEF 0

    BA98 17 26 35 4

    IN

    OUT

    NODE

    USB

  • ·30·

    Installation manual

    CNC 8055CNC 8055i

    1.

    8055

    CN

    C C

    ON

    FIG

    UR

    AT

    ION

    SOFT: V01.3X

    Cen

    tral

    uni

    t

    Central Unit (CPU) configuration

    The configuration of the central unit depends on each application. The –CPU– and –AXES– modulesmust be part of all configurations.

    The –CPU– module must be the first one from the left. The rest of the modules do not have to followa particular order and may be interchanged according to personal preferences and connectionpossibilities of the machine.

    The CNC has a PLUG&PLAY system that recognizes the configuration of the central unit. To do that,regardless of their physical location, each module has a logic address or device select code whichidentifies it within the internal configuration of the CNC. The logic address (device select code) foreach module is factory set as follows:

    –Axes– module Logic address 2.

    –I/O– module (1) Logic address 3.

    –I/O– module (2) Logic address 4.

    –I/O– module (3) Logic address 5.

    Nevertheless, except in the axes module, these logic addresses may be modified at will. To do that,use the microswitches located in one of the corners of the printed circuit board.

    The logic address is set in binary code between 1 and 14. Logic address "0" and "15" are reserved.Logic addresses 0 and 15 are reserved.

    When using several –I/O– modules, the CNC assumes the one with the lowest address as the firstexpansion module, as –I/O– (2) module the next address and as –I/O– (3) the one with the highestaddress number.

    Logic address

    Micro switch position Logic address

    Micro switch position

    1 2 3 4 1 2 3 4

    0 off off off off 8 on off off off

    1 off off off on 9 on off off on

    2 off off on off 10 on off on off

    3 off off on on 11 on off on on

    4 off on off off 12 on on off off

    5 off on off on 13 on on off on

    6 off on on off 14 on on on off

    7 off on on on 15 on on on on

    I/O

    X1

    X2

    X3

    1 2

    3 4

    ON

    OFF

  • Installation manual

    CNC 8055CNC 8055i

    8055

    CN

    C C

    ON

    FIG

    UR

    AT

    ION

    1.

    SOFT: V01.3X

    ·31·

    Cen

    tral

    uni

    t

    Dimensions and installation

    The central unit is supplied with the requested configuration and its mounted on to the electricalcabinet by means of the holes located on its back for that purpose. Care must be taken to positionthe power supply at the bottom.

    FAGOR

    I/O

    X1

    X2

    X3

    AXES

    X1 X2

    X3 X4

    X5 X6

    X7 X8

    X9X10

    CPU

    X1 X2

    CMPCTFLASH

    ETH

    COM1

    X3

    CDE

    F0

    BA98 17 26 354

    IN

    OUT

    NODE

    USB

    FAGOR

    I/O

    X1

    X2

    X3

    I/O

    X1

    X2

    X3

    I/O

    X1

    X2

    X3

    I/O

    X1

    X2

    X3

    AXES

    X1 X2

    X3 X4

    X5 X6

    X7 X8

    X9X10

    CPU

    X1 X2

    CMPCTFLASH

    ETH

    COM1

    X3

    CDE

    F0

    BA98 17 26 354

    IN

    OUT

    NODE

    USB

    125 (4.92)

    77 (3.03)24 (0.94)

    347

    (13.

    66)

    365

    (14.

    37)

    389

    (15.

    31)

    20 (0

    .79)

    15,5

    (0.6

    1)

    274,5 (10.8

    1)253 (

    9.96)

    10 (0.39)8 (0.31)

    6 (0.24)

    6 (0.24)

    245 (9.65)

    98,5 (3.88)

    347

    (13.

    66)

    365

    (14.

    37)

    389

    (15.

    31)

    20 (0

    .79)

    15,5

    (0.6

    1)

    274,5 (10.8

    1)253 (

    9.96)

    98,5 (3.88)24 (0.94)

  • ·32·

    Installation manual

    CNC 8055CNC 8055i

    1.

    8055

    CN

    C C

    ON

    FIG

    UR

    AT

    ION

    SOFT: V01.3X

    Cen

    tral

    uni

    t

    Central Unit (CPU) voltage supply

    Power the central unit through a separate 110VA transformer with an output voltage between 84Vacand 264Vac and 50-60 Hz.

    1. Indicator led. When ON, it indicates that the central unit is under power.

    2. Lithium battery. Maintains the RAM memory data when the system is powered off.

    3. Mains plug. Is used to power the central unit by connecting it to the transformer and to ground.

    4. Ground terminal. All ground terminals of the machine must be connected to this terminal. Metric6mm.

    When detecting a voltage peak, wait for 3 minutes before turning it on again.

    For further technical information, refer to the appendix at the end of this manual. See "Central unitof the 8055 CNC" on page 625.

    Do not get into the inside of the unit.• Only authorized personnel from Fagor Automation may do it.

    Do not handle the connectors with the unit connected to main AC power.• Before manipulating these connectors, make sure that the unit is not connected to main AC power.

    FAGOR

    I/O

    X1

    X2

    X3

    AXES

    X1 X2

    X3 X4

    X5 X6

    X7 X8

    X9 X10

    CPU

    X1 X2

    CMPCTFLASH

    ETH

    COM1

    X3

    CDEF0

    BA98 17 26 354

    IN

    OUT

    NODE

    USB

    FAGOR

    1 2 3

    4

  • Installation manual

    CNC 8055CNC 8055i

    8055

    CN

    C C

    ON

    FIG

    UR

    AT

    ION

    1.

    SOFT: V01.3X

    ·33·

    Cen

    tral

    uni

    t

    1.2.1 –CPU– Module

    Besides containing the system software, this module performs all the functions of the CNC (edit,execute, display, etc.) as well as processing the information from the rest of the modules andgenerating video signals for the monitor.

    The connectors that permit connecting the central unit with the monitor and the keyboard are locatedin this module.

    Elements

    When replacing the–CPU– module, the contents of the internal RAM memory are kept for about 24hours as long as it has been previously on for more than 1 minute; but the date and the time will belost and will have to be set again.Do not get into the inside of the unit.

    • Only personnel authorized by Fagor Automation may manipulate the inside of this unit.Do not handle the connectors with the unit connected to main AC power.

    • Before manipulating these connectors, make sure that the unit is not connected to main AC power.Peripheral connection and disconnection.

    • The CNC must be powered off when connecting or disconnecting any peripheral throughconnector X3 (RS232C).

    • When the mains connection of the PC or peripheral device is not referenced to ground, it isrecommended to connect the cable shield to the connector hood only at the CNC end.

    CPU

    X1 X2

    CMPCTFLASH

    ETH

    COM1

    X3

    C DE F0

    BA98 17 26 354

    IN

    OUT

    NODE

    USB

    Connector ·X2·Connector for connecting it with the monitor(digital video output for Fagor monitors).25-pin SUB-D type male connector.

    Connector ·X1·Connector for the Keyboard connection.25-pin SUB-D type female connector.

    Slot KeyCFCompartment of the compact flash memorywith the CNC configuration (KeyCF).

    USBType A USB 1.1 connector.It admits connecting a "Pen Drive" typememory device.

    EthernetEthernet connector to configure the CNCwithin a local network.

    COM1Connector for the digital servo system(CAN or Sercos).

    Connector ·X3·Connector for the serial communication lineRS232.9-pin SUB-D type male connector.

  • ·34·

    Installation manual

    CNC 8055CNC 8055i

    1.

    8055

    CN

    C C

    ON

    FIG

    UR

    AT

    ION

    SOFT: V01.3X

    Cen

    tral

    uni

    t

    Connectors and connection

    Connector X1 - for the Keyboard connection

    SUB-D type 25-pin female connector to connect the central unit with the keyboard.

    FAGOR AUTOMATION provides the cable necessary for this connection. This cable has two 25-pin male connectors of the SUB-D type.

    Both connectors have a latching system by means of two screws UNC4.40.

    It is a straight connection, 1 to 1, 2 to 2, 3 to 3 and so on. The cable hose shield is soldered to themetal hoods covering both connectors.

    Connector X2 - for Fagor monitors

    25-pin male connector of the SUB-D type to connect the central unit with the monitor.

    Fagor Automation provides the cable necessary for this connection. This cable has two 25-pinfemale connectors of the SUB-D type.

    Both connectors have a latching system by means of two screws UNC4.40.

    It is a straight connection, 1 to 1, 2 to 2, 3 to 3 and so on. The cable hose shield is soldered to themetal hoods covering both connectors.

    Connector X3 - RS232

    It is a 9-pin SUB-D type male connector to connect the RS 232 C serial port.

    The cable shield must be connected to the metallic hood at each end.

    All the pins of this connector are opto-isolated.

    Cable length.

    EIA RS232C standards specify that the capacitance of the cable must not exceed 2500pF; therefore,since average cables have a capacitance between 130pF and 170pF per meter, the maximum lengthof the cable should not be greater than 15m (49ft).

    Shielded cables with twisted-pair wires should be used to avoid communication interference whenusing long cables.

    Use shielded 7 conductor cable of 0.14 mm2 section.

    Transmission speed.

    The CNC can operate at up to 115,200 Baud.

    It is recommended to ground the unused pins in order to avoid erroneous control and data signalinterpretations.

    Ground connection.

    It is suggested to reference all control and data signals to the same ground cable (pin -GND-) thus,avoiding reference points at different voltages especially in long cables.

    Pin Signal

    123456789

    DCDRxDTxDDTR

    GND ISODSRRTSCTS- - -

    1

    5

    6

    9

  • Installation manual

    CNC 8055CNC 8055i

    8055

    CN

    C C

    ON

    FIG

    UR

    AT

    ION

    1.

    SOFT: V01.3X

    ·35·

    Cen

    tral

    uni

    t

    Recommended RS232C interface connection.

    Slot "KEYCF" - Compartment of the KeyCF (CNC configuration card)

    It has a compact flash type hard disk to store user programs and for updating software versions.The hard disk may be accessed from the outside.

    The KeyCF supplied by Fagor with each CNC has an identification code corresponding to:

    • The card id (all the cards are different).

    • The software features that have been purchased for that unit

    The id code only needs very little memory space. The rest of memory space of the KeyCF may beused to store data on machine customizing (user screens, PLC program backup and/or machineparameters, etc.) as well as user part-programs.

    The CNC will recognize the KeyCF as .

    When having the Ethernet option, it is possible to use a PC directory as a remote hard disk.

    Simplified connection Full connection.

    CNC PC (9pin)Hold Hold

    FG

    RxDTxD

    DSR

    DTR

    CTS

    RTS

    GND

    DCD

    RxDTxD

    DTR

    DSR

    RTS

    CTS

    GND

    1

    2

    3

    4

    6

    7

    8

    5

    1

    2

    3

    6

    4

    8

    7

    5

    CNC PC (25pin)Hold Hold

    FG

    TxD

    RxD

    DSR

    DTR

    CTS

    RTSGND

    DCD

    RxD

    TxD

    DTR

    DSR

    RTS

    CTSGND

    1

    2

    3

    4

    6

    7

    8

    5

    1

    23

    620

    5

    4

    7

    CNC PC (9pin)Hold Hold

    FG

    RxDTxD

    DSR

    DTR

    CTS

    RTSGND

    DCD

    RxDTxD

    DTR

    DSR

    RTS

    CTSGND

    1

    2

    3

    4

    6

    7

    8

    5

    1

    2

    3

    64

    8

    7

    5

    CNC PC (25pin)Hold Hold

    FG

    TxD

    RxD

    DSR

    DTR

    CTS

    RTSGND

    DCD

    RxD

    TxD

    DTR

    DSR

    RTS

    CTSGND

    1

    2

    3

    4

    6

    7

    8

    5

    1

    2

    3

    6

    20

    5

    4

    7

  • ·36·

    Installation manual

    CNC 8055CNC 8055i

    1.

    8055

    CN

    C C

    ON

    FIG

    UR

    AT

    ION

    SOFT: V01.3X

    Cen

    tral

    uni

    t

    "USB" port - USB hard disk (Pen Drive) connection.

    The USB 1.1 port with type A connector admits connecting a "Pendrive" type memory device. Thesememory devices are commercially available (off-the-shelf) and they're all valid regardless of theirsize, brand name or model.

    When using a USB extension cable, it must be an "A" - "B" type cable and must not be longer than3 m. Also, we recommend using a double-shielded cable.

    The CNC recognizes the connected device as USB Hard Disk. When it is connected, it will be shownas on the left panel of the . To see its contents, press the (refresh) softkey.

    Within the USB device, the CNC will only recognize files with extensions *.f55 (software version),*fhw (Firmware updating files), part-programs parameters, tables, screens and symbols. The CNCwill not recognize any other type of file. Part-programs cannot be edited or executed from the USBhard disk.

    Independent monitors (without keyboard)

    Connecting the USB extension set supplied by Fagor:

    1. Connect the cable and the USB adaptor. Check that the seal and the nut of the USB adaptorare secured as shown in the figure.

    2. While the CNC is off, connect the extension cable to the USB connector of the CNC.

    3. Once the extension set has been properly connected, you may connect the USB devices throughan adapter.

    Do not connect a multi-hub USB adapter to connect several devices at the same time. It will onlyrecognize the first Pen Drive that is connected. Nor will it recognize other types of devices such askeyboards, mice, recorders, etc.

    USB extension cable.

    USB adapter.

    Securing nut.

    Seal.

    FAGOR

    F1 F2 F3 F4 F5 F6 F7

    CPU

    X1 X2

    CMPCTFLASH

    ETH

    COM1

    X3

    C DEF0

    BA98 1

    7 26 354

    IN

    OUT

    NODE

    USB USB extension cable.

    USB adapter.To connect USB devices.

  • Installation manual

    CNC 8055CNC 8055i

    8055

    CN

    C C

    ON

    FIG

    UR

    AT

    ION

    1.

    SOFT: V01.3X

    ·37·

    Cen

    tral

    uni

    t

    Monitors with keyboard

    Connection of the USB extension cable supplied by Fagor

    1. While the CNC is off, connect the extension cable to the CPU and to the keyboard.

    2. Once the extension cable has been properly connected, you may use the USB connector of thekeyboard.

    Ethernet - CNC configuration in a local network

    The Ethernet option permits configuring the CNC as another node within the local area network.This makes it possible to communicate with other PC's to transfer files or carrying out telediagnostictasks.

    The Ethernet option does not require having the DNC option available.

    The Ethernet card has an RJ-45 connector and two LED's that inform on the status of the connection.

    Red LED Blinks while transmitting data.

    Green LED On while connected to the network.

    Use a standard shielded 10BASE-T cable for this connection. It must not be longer than 100 meters.

    Once the connection to Ethernet has been configured, the following types of connections arepossible:

    • PC connection through WinDNC (it requires WinDNC version 4.0 or higher).

    • Connection from a PC through an FTP client.

    • Connection to a remote hard disk.

    CPU

    X1 X2

    CMPCTFLASH

    ETH

    COM1

    X3

    CDEF0

    BA98 1

    7 26 354

    IN

    OUT

    NODE

    USB

    FAGOR

    0

    2

    4

    1020

    3040 50 60

    7080

    90

    10 0

    11 0

    12 0

    FEED %SPINDLEJOG

    10 0

    101

    1 10 10 010 00

    10 00 0

    Type AUSB

    Type BUSB

    The type B USB connectoris connected in the back ofthe keyboard.

    Network connection

    Transmitting data

  • ·38·

    Installation manual

    CNC 8055CNC 8055i

    1.

    8055

    CN

    C C

    ON

    FIG

    UR

    AT

    ION

    SOFT: V01.3X

    Cen

    tral

    uni

    t

    Remote hard disk.

    The Ethernet connection may be used to use a PC directory (server) as a hard disk. This memoryspace may be shared by several CNC's or each may have its own memory space.

    The interface and the softkeys of the CNC will the same as if it were a local hard disk. When accessingthe CNC through WinDNC or FTP, the remote hard disk behaves like a local hard disk.

    The remote hard disk is configured by machine parameters. The PC that makes its hard disk (server)public must be connected to the local network.

    COM1 - Digital servo (CAN or Sercos)

    The digital servo system (CAN or Sercos) is connected to COM1. This servo system is enabledthrough its corresponding software option.

    Two types of digital servo system may be used to communicate with Fagor servo drives:

    • Sercos interface IEC1491.

    • CAN field bus and standard CanOpen communication protocol. In general, their characteristicsare similar to those of the Sercos ring with lower transmission speed.

    The same system may have digital axes (CAN or Sercos) and analog axes. On the other hand, itis not possible to have digital axes with Sercos interface and CAN interface at the same time.

    Digital CAN servo

    Module identification at the bus.

    Each one of the elements integrated into the CAN bus is identified by the 16-position rotary switch(0-15) "Address" (also referred to as "Node_Select"). This rotary switch selects the address (node)occupied by each element integrated in the bus.

    Although the switch has 16 positions, only positions 1 through 8 are valid. The CNC does not havea switch, The drives occupy consecutive positions (recommended) starting from ·1·.

    The corresponding drive must be turned off and back on (or press the Reset button) for the addresschange to be assumed.

    The NFS protocol is used to communicate with the remote hard disk. This protocol must be availableat the PC that is used as server.i

    Error

    Status

  • Installation manual

    CNC 8055CNC 8055i

    8055

    CN

    C C

    ON

    FIG

    UR

    AT

    ION

    1.

    SOFT: V01.3X

    ·39·

    Cen

    tral

    uni

    t

    The "Line_Term" switch.

    The "Line_Term" switch identifies which are the elements that occupy the ends of the CAN bus; i.e.the first and last physical element in the connection.

    The central unit must always be at one end of the line. The other end will be the last one of the remotemodule groups.

    The switch position of the terminating elements must be "1" and that of the rest of the elements "0".The CNC does not have a switch and always has the terminating resistor activated.

    Characteristics of the CAN cable.

    Use a specific CAN cable. The ends of all the wires and the shield must be protected by thecorresponding pin. Also use the pins to secure the cable to the connector.

    Type: Shielded. Twisted pairs (1 x 2 x 0,22 mm2).

    Flexibility: Superflexible. Minimum static bending radius of 50 mm and a dynamicradius of 95 mm.

    Cover: PUR

    Impedance: Cat.5 (100 - 120 )

    CAN connector pinout

    5-pin male Phoenix minicombicon connector (3.5 mm pitch).

    The connector has two shield pins. Both pins are equivalent; the CAN shield may be connected toeither one.

    Signal Description

    ISO GND Ground / 0 V.

    CAN L Bus signal (LOW).

    SHIELD CAN shield.

    CAN H Bus signal (HIGH).

    SHIELD CAN shield.

    ISO GND

    CAN L

    SHIELD

    CAN H

    SHIELD

    1

    2

    3

    4

    5

    1

    2

    3

    4

    5

    Pin Pin

  • ·40·

    Installation manual

    CNC 8055CNC 8055i

    1.

    8055

    CN

    C C

    ON

    FIG

    UR

    AT

    ION

    SOFT: V01.3X

    Cen

    tral

    uni

    t

    Interconnection of modules.

    It is connected in series. The figure shows the CAN connection between the central unit and 2 drives.

    Sercos digital servo system

    Module identification at the bus.

    Each element integrated into the Sercos bus is identified with the 16-position rotary switch (0-15)"Address" (also known as Node_Select). This rotary switch selects the address (node) occupiedby each element integrated in the bus.

    The CNC must always occupy the "0" position and the rest will occupy the consecutive positionsstarting from "1". The corresponding drive must be turned off and back on (or press the Reset button)for the address change to be assumed.

    The fact that the drive identified with number 1 (for example) corresponds to the X axis, to Y or toanother one is irrelevant. However, it is a good idea, for the sake of clarity, that the machine axesX, Y, Z, U, V, W, A, B and C are numbered sequentially in that order.

    Sercos connector pinout.

    Signal Description

    IN Sercos connection input.

    OUT Sercos connection output.

    CDEF0

    BA

    98 17 26 35 4

    ADDRESS=1

    LINE TERM=0

    0 1

    ISO GNDCAN L

    SHIELDCAN H

    SHIELD

    DRIVE MODULE 1

    C DEF0

    BA98 17 26 35 4

    ADDRESS=2

    LINE TERM=1

    0 1

    ISO GNDCAN LSHIELDCAN HSHIELD

    DRIVE MODULE 2

    ISO GNDCAN L

    SHIELDCAN H

    SHIELD

    CNC

    CDEF0

    BA98 17 26 35 4

    IN

    OUT

    NODE

    IN

    OUT

    IN

    OUT

    IN

    OUT

  • Installation manual

    CNC 8055CNC 8055i

    8055

    CN

    C C

    ON

    FIG

    UR

    AT

    ION

    1.

    SOFT: V01.3X

    ·41·

    Cen

    tral

    uni

    t

    Sercos cable characteristics.

    Fagor Automation provides the fiber optic cables needed for Sercos communication. There aredifferent types of cables depending on length and dynamic and static installation characteristics.

    • Fiber optic cable with polymer core (SFO, SFO-FLEX) for up to 40 meters If the cable will besubject to dynamic conditions (it will be moving), the SFO-FLEX cable must always be used.If the cable will be subject to static conditions (it will not be moving), the SFO cable will be enough.

    • Fiber optic cable with glass core (SFO-V-FLEX) for more than 40 meters.

    Mechanical characteristics of the cables.

    Cable handling.

    Fagor supplies the cable with the terminals protected by a cap. Remove the protection cap beforeconnecting the cable.

    To remove the terminal protecting cap or to connect or disconnect the cable, hold the cable by itsterminal; never pull the cable by holding its plastic part because it could render it useless.

    SFO cable

    Flexibility. Normal. Minimum bending radius: 30 mm.Only to be used when the cable will not be moving (static conditions).

    Covering. PUR. Polyurethane resistant to chemical used on machines.

    Temperature. Work: -20 ºC / 80 ºC (-4 ºF / 176 ºF).Storage: -35 ºC / 85 ºC (-31 ºF / 158 ºF).

    SFO-V-FLEX cable

    Flexibility. Minimum bending radius: 16 mm.Special cables to be used in cable carrying chains.

    Temperature. Work: -65 ºC / 125 ºC (-85 ºF / 257 ºF).

    SFO-FLEX cable

    Flexibility. High. Minimum static bending radius of 50 mm and a dynamic radius of 70 mm.Special cables to be used in cable carrying chains.

    Covering. PUR. Polyurethane resistant to chemical used on machines.

    Temperature. Work: -20 ºC / 70 ºC (-4 ºF / 158 ºF).Storage: -40 ºC / 80 ºC (-40 ºF / 176 ºF).

  • ·42·

    Installation manual

    CNC 8055CNC 8055i

    1.

    8055

    CN

    C C

    ON

    FIG

    UR

    AT

    ION

    SOFT: V01.3X

    Cen

    tral

    uni

    t

    Interconnection of modules.

    It is connected in a ring through optic fiber, by joining an OUT terminal with an IN terminal. The figureshows the Sercos connection of the CNC with Fagor spindle drives and axes X and Y.

    CDE F0

    BA98 17 26 35 4

    IN

    OUT

    NODE

    IN

    OUT

    CDE F0

    BA98 17 26 35 4

    NODE

    IN

    OUT

    C DEF0

    BA98 17 26 35 4

    NODE

    IN

    OUT

    CDEF0

    BA98 17 26 35 4

    NODE

    CDEF0

    BA98 17 26 35 4

    CNC SPINDLE X AXIS Y AXIS

    Node=2Node=1Node=3Node=0

    C DEF0

    BA98 17 26 35 4

    C DEF0

    BA98 17 26 35 4

    CDEF0

    BA98 17 26 35 4

  • Installation manual

    CNC 8055CNC 8055i

    8055

    CN

    C C

    ON

    FIG

    UR

    AT

    ION

    1.

    SOFT: V01.3X

    ·43·

    Cen

    tral

    uni

    t

    1.2.2 –Vpp Axes– module

    This module will appear in / / with the nameof "Axis module 2".

    Besides controlling the spindle and the axes of the machine, it governs the first 40 digital PLC inputsand 24 digital PLC outputs. This module offers the following to communicate with the outside world:

    4 Feedback inputs admitting single-ended and double-ended (differential) TTL signals as well assingle-ended 1Vpp sinusoidal signals.

    4 Feedback inputs admitting single and double-ended (differential) TTL signals.

    8 Analog command outputs for the servo drives.

    4 Free differential analog inputs for controlling, monitoring or supervising systems.

    2 Digital probe inputs.

    24 Digital outputs ,optocoupled, commanded by the PLC.

    40 Digital inputs ,optocoupled, read by the PLC.

    Elements

    AXES

    X1 X2

    X3 X4

    X5 X6

    X7 X8

    X9X10

    Connectors ·X1·, ·X2·, ·X3· and ·X4·SUB-D HD type 15-pin female connectorsfor feedback systems of each axis. Theyaccept sinewave signals.

    Connectors ·X5· and ·X6·SUB-D type 15-pin male connectors forfeedback system of the axes. Up to 2 axesmay be connected per connector. They donot accept sinewave signals.

    Connector ·X8·SUB-D type 15-pin female connector toconnect up to 8 analog outputs (range±10V).

    Connector ·X7·SUB-D type 15-pin male connector toconnect up to 4 differential analog inputs(range ±10 V) and two probe inputs (TTL or24 V).

    Connector ·X10·SUB-D type 37-pin female connector for the8 digital inputs of the PLC and its 24 digitaloutputs.Connector ·X9·

    37-pin male connector of the SUB-D typefor 32 digital inputs of the PLC.

    Do not open this unit. Only personnel authorized by Fagor Automation may open this unit. Do not handle the connectors with the unit connected to mains. Before doing it, make sure that theunit is disconnected.The machine manufacturer must comply with the "EN 60204-1 (IEC-204-1)", standard regardingprotection against electrical shock due to I/O contact failures with external power supply when nothooking up this connector before turning the power supply on.

  • ·44·

    Installation manual

    CNC 8055CNC 8055i

    1.

    8055

    CN

    C C

    ON

    FIG

    UR

    AT

    ION

    SOFT: V01.3X

    Cen

    tral

    uni

    t

    Signal adapters

    The following signal adapters are available to be used with the –Vpp axes– module.

    SA-TTL-TTLD Adapter for "Non-differential TTL" to "differential TTL" signals

    SA-FS-P Adapter for Fagor sinusoidal signals to Vpp signals

    Technical characteristics of the feedback inputs

    Power supply consumption of +5 V 1 A (250 mA per axis).

    Work levels for differential square signal.

    Work levels for non-differential square signal.

    Work levels for sinusoidal signal.

    Maximum frequency: 500 kHz

    A and B signals Amplitude: 0.6 ÷ 1.2 Vpp

    Centered: |V1-V2| / 2 Vpp =< 6.5%

    Relationship: VApp / VBpp = 0.8 ÷ 1.25

    Phase shift: 90º ± 10º

    Reference mark (I0) signalAmplitude: 0.2 ÷ 0.85 V

    Width: T-90º =< I0 =< T+180º

    Maximum frequency: 1000 kHz.

    Maximum gap between flanks: 460 ns.

    Phase shift: 90º ± 20º.

    Vmax in common mode: ± 7 V.

    Vmax in differential mode: ± 6 V.

    Hysteresis: 0,2 V.

    Maximum differential input current: 3 mA.

    Maximum frequency: 400 kHz.

    Maximum gap between flanks: 460 ns.

    Phase shift: 90º ± 20º.

    High threshold (logic level "1") VIH: 1.25 V < VIH < 7 V.

    Low threshold (logic level "0") VIL: -7 V < VIL < 1 V.

    Vmax: ± 7 V.

    Hysteresis: 0,25 V.

    Maximum differential input current: 3 mA.

    A

    B

    Io

    V1 VAPP

    V2

    VBPP

    VIOPP

  • Installation manual

    CNC 8055CNC 8055i

    8055

    CN

    C C

    ON

    FIG

    UR

    AT

    ION

    1.

    SOFT: V01.3X

    ·45·

    Cen

    tral

    uni

    t

    Connectors and connection

    Connectors X1, X2, X3, X4 - Differential TTL and 1Vpp sinusoidal feedback signals

    They are 15-pin female connectors of the SUB-D HD type and they are used for