Email: [email protected] Website: www.cmsdanskin.co.uk
Scotland Office: 1 Netherton Road Wishaw ML2 OEQ
Central Office: Unit 2 Lyncastle Road Warrington Cheshire WA4
4SN
Southern Office: Unit 8 Harding Way St Ives Cambridge PE27
3WR
t: 01698 356000 f: 01698 372222
t: 01925 577711 f: 01925 577733
t: 01480 463750 f: 01480 495180
Installation Guidelines
TECHNICAL INFORMATION SHEET
Guarantee
Description
Physical information
Installation
Technical information
Storage
CMS BOND 100
*Please contact CMS Danskin for further information.
CMS Bond 100 is distributed in the UK by CMS Danskin. The
adhesive manufacturer will guarantee the performance and quality of
products against manufacturing defects provided they are used in
accordance with our relevant Technical Data Sheets at the time of
installation and the appropriate sub floor preparation has been
undertaken in accordance with the relevant British Standards.
Floor covering manufacturers are constantly introducing new
backings and improving their current products. Certain backings may
have unique characteristics, which may influence the choice of
adhesive used. Whilst every effort has been made to ensure the
information is correct at the time of publication it is the
responsibility of the user to ensure that the product is suitable
for the particular installation.
If there is any doubt as to the use of our adhesives the
installer should contact CMS Danskin for advice or carry out their
own tests to ensure compatibility.
CMS Bond 100 is a solvent free, low VOC, high performance, water
based acrylicdispersion with very good bond strength.
It is suitable for plasticized vinyl floor coverings (including
PVC Tiles) togetherwith high density foam backed carpets.
Colour Off White Consistency Trowelable MasticOpen time 15
minutes plus depending on site conditions: Temp, humid &
surfaces to be treatedSpecific Gravity 1.2Shelf life 12 months if
stored between 5-30C in a cool dry area, in original unopened
containers. Protect from frost.
Surface preparation
1. Suitable sub-flooring substrates include concrete, flooring
grade hardboard, plywood, chipboard, sand/cement screed,
proprietary good quality self-smoothing underlayments. Asphalt and
surface membranes should be treated with at least a 3mm coating of
the latter before applying adhesive.
2. Site conditions should comply with the latest British
Standards editions: BS 8102 (Code of Practice for protection
against moisture from the ground), BS 8203 (Code of Practice for
installation of resilient floor coverings), BS 5325
(Code of Practice for installation of textile floor coverings),
BS 8204 part 1 (Code of Practice for installation of self levelling
screeding compounds), and supplementary specifications.
3. Surfaces must be level, firm and clean, free of loose
material, mould, oil, grease, organic growth and surface
moisture.
4. Uneven, dusty or friable surfaces should be treated with the
appropriate universal primer and screed.*
5. It is essential that suitable damp proof membranes be in
place to prevent rising damp.*
6. Under floor heating should be turned off for at least 48 hrs
prior to and after application.
7. Particular attention must be paid to the floor covering
manufacturers instructions. i.e. any pre storage conditions prior
to fitting.
Curing High humidity, a low temperature and poor ventilation
will retard the drying speed.Coverage 3m/kg depending on the
porosity of the substrate and thickness of the adhesive film.
CMS Bond 100 must be kept in an airtight container and stored at
a moderatetemperature.
Email: [email protected] Website: www.cmsdanskin.co.uk
Scotland Office: 1 Netherton Road Wishaw ML2 OEQ
Central Office: Unit 2 Lyncastle Road Warrington Cheshire WA4
4SN
Southern Office: Unit 8 Harding Way St Ives Cambridge PE27
3WR
t: 01698 356000 f: 01698 372222
t: 01925 577711 f: 01925 577733
t: 01480 463750 f: 01480 495180
Installation Guidelines
IMPORTANT: Directions for use are given for guidance only and
are not intended to form part of any contract. They should be
varied or adapted to suit your particular materials or conditions
of use. Goods suppliedby the company are made to approved standards
from the highest quality raw materials but no warranty or guarantee
is given as to their suitability for any particular purpose or
application, and no liability is accepted for any loss or damage
arising directly or indirectly from the use of the Companys
products irrespective of any information given to us as to intended
use of such products. It is therefore recommended that prospective
users should test a sample of this product under their own
conditions to satisfy themselves that the product is suitable for
the purpose intended.
CADS 4004 1 0904 CMS Danskin Acoustics Ltd
Installation Cont.
Drying Times
Health and Safety
The floor temperature should be above 10C and remain assuch
throughout the application and drying of the adhesive. If these
conditions are met then the adhesive must be left for a minimum of
24 hours to fully cure. If the temperature is below 10C or
significantly higher the overall drying/curing time will vary and
is then at the discretion of the responsible flooring
contractor.
If the floor has underfloor heating we would recommend that this
be turned off at least 48 hours prior to work commencing.
Important Note
The information contained in this datasheet is based on
testsbelieved to be reliable, practical experience and is published
ingood faith. However because we have no control over the
application conditions we do not guarantee the results
obtained.Responsibility for establishing suitability of the product
rests with the purchaser. No liability or claim for damage or
consequential loss is accepted from the use of this product.
Do not ingest. Keep away from children and pets. Do not empty
into drains. Wear rubber gloves. Avoid contact with eyes. Allow any
unused product to dry before disposing of the container. In the
event of contamination, rinse thoroughly with cold water. Seek
medical assistance if irritation or discomfort persists. H & S
Data Sheet available on request.
CMSD2 11/12/RS
Mixing
CMS Bond 100 is a ready to use versatile product and should not
be diluted or adulterated in any way.
Application
1. Use a notched trowel of dimensions 1.5mm x 5mm or as CFA
guidelines.
2. Heavy textured floor coverings may require a larger
trowel.
3. Apply adhesive evenly to the substrate and depending on the
substrates lay the floor covering while still wet. It is best
to
allow the freshly applied adhesive to stand for 15-45 minutes
depending on the ambient conditions, to build tack before embedding
the floor covering.
4. Press firmly into place and roll using a 60/70Kg roller or
glider depending on material used. Roll again approximately 1 hr
after application.
5. Wait at least 24 hrs before welding vinyl seams.
Removal of adhesive from tools
Clean tools with water if adhesive is still wet or use white
spirits if it has dried.
