CLX-3170 Series trainingCLX-3170 Series training

AgendaAgenda

I. General Specification

I. Product Overview

II. Product General Specification

III. Review

II. Feature Details

I. UI (Control Panel / Menu Structure)

II. F/W Upgrade

III. Reports

IV. Messages

V. Special Operation

VI. Tech Mode

Part. Part. Ⅰ General Specification General Specification

I. Specificationa) Speed - 16ppm B&W, 4ppm colorb) Consumables - Black toner (1.5K sheet), CMY toner (1K sheet)a) Paper - 1sheet Manual slot, 150 sheet Semi-cassetted) Device interface - USB 2.0, Ethernet 10/100 Base TX, USB host (PictBridge)

II. Concepta) The World Smallest Color MFP (A4 Color laser MFP:4 In 1)b) Target users - Small office & businessc) Base Engine : CLP-310 Seriesd) Network Support(CLX-3170FN / CLX-3170FW)e) USB host function - PictBridge, Scan to USB memory, Direct printing

Product Overview

Product General Specification

• CPU– Type : CHORUS3 (ARM 920T core)– Speed : 360MHz– Bus speed : 120MHz– One chip solution (HPVC, I/O, JBIG, network …)

• Real-Time OS – pSOS (V2.5)

• Driver– SPLC

Product Series

Items CLX-3170 Series

Model Name 　 CLX-3170 CLX-3170N

Print

　 Printer Language

SPL-C (Samsung Printer Language

Color)

SPL-C (Samsung Printer Language

Color)

Fonts N/A N/A

OP UI 2 x 16 LCD, AUI 2 x 16 LCD, AUI

Scan

Resolution600 x 1200dpi (Optical)

4800dpi x 4800dpi (Enhanced)600 x 1200dpi (Optical)

4800dpi x 4800dpi (Enhanced)

DepthColor(24bits),

Mono(1bit), Gray(8bits)Color(24bits),

Mono(1bit), Gray(8bits)

Scan To Application, USBApplication,

Network scan, USB

Copy

Multi Copy 1~99 1~99

Darkness Control 3 level 3 level

Zoom RangePlaten: 25 ~ 400%ADF: 25 ~ 100%

Platen: 25 ~ 400%ADF: 25 ~ 100%

Special CopyID, Auto Fit, Clone, Poster,

2-up, 4-upID, Auto Fit, Clone, Poster

2-up, 4-up, Network Print N/A Wire

USBDirect Print Yes( JPG, TIFF, BMP) Yes( JPG, TIFF, BMP)

PictBridge Yes Yes

FaxCompression N/A N/A

Color Fax N/A N/ASound Control N/A N/A

Product General Specification

Items CLX-3170 Series

Model Name 　 CLX-3170FN CLX-3170FW

Print　 Printer Language

SPL-C (Samsung Printer Language

Color)

SPL-C (Samsung Printer Language

Color)Fonts N/A N/A

OP UI 2 x 16 LCD, AUI 2 x 16 LCD, AUI

Scan

Resolution600 x 1200dpi (Optical)

4800dpi x 4800dpi (Enhanced)600 x 1200dpi (Optical)

4800dpi x 4800dpi (Enhanced)

DepthColor(24bits),

Mono(1bit), Gray(8bits)Color(24bits),

Mono(1bit), Gray(8bits)

Scan ToApplication,

Network scan, USBApplication,

Network scan, USB

Copy

Multi Copy 1~99 1~99Darkness Control 3 level 3 level

Zoom RangePlaten: 25 ~ 400%ADF: 25 ~ 100%

Platen: 25 ~ 400%ADF: 25 ~ 100%

Special CopyID, Auto Fit, Clone, Poster,

2-up, 4-upID, Auto Fit, Clone, Poster

2-up, 4-up, Network Print Wire Wire & Wireless( 무선랜 )

USBDirect Print Yes( JPG, TIFF, BMP) Yes( JPG, TIFF, BMP)

PictBridge Yes Yes

Fax

Compression MH/MR/MMR/JBIG/JPEG MH/MR/MMR/JBIG/JPEG

Color FaxDefault (Memory TX & Any

Reserved Transmission are not supported)

Default (Memory TX & Any Reserved Transmission are not

supported)Sound Control Ring, Key, Speaker, Alarm Ring, Key, Speaker, Alarm

Product General Specification

Part. Part. Ⅱ Feature Details Feature Details

UI(1) – Control Panel Overview

STATUS DESCRIPTION

Off • The machine is powered off-line. • The machine is in power save mode. When data is received, or any button is pressed, it switches to on-line automatically. • Wireless function can not be used.

Green Blinking • When the green LED slowly blinks, the machine is receiving data from the computer. • When the green LED rapidly brinks, the machine is printing data.

On • The machine is powered on and can be used. • Wireless function can be used.

Red Blinking • A minor error has occurred and the machine is waiting for the error to be cleared. Check the display message, and solve the problem referring to "Understanding display messages" on page 71. • The toner cartridge is low. Order a new toner cartridge, see "Ordering supplies" on page 82. You can temporarily improve print quality by redistributing the toner. (See "Replacing the toner cartridge" on page 63.)

On • A problem has occurred such as a paper jam, cover is open or no paper in the tray, so that the machine cannot continue the job. Check the message on the display, and refer to "Understanding display messages" on page 71 to solve the problem. • The toner cartridge is empty, exhausted, or needs to be changed. (See "Understanding display messages" on page 71.)

UI(2) – Basic Menu Structure

F/W Upgrade

It is possible to update F/W via USB and Network port

Support updating F/W using Network applications software (SWAS, SWS)

Normal UpdateSend ROM image file to MFP in Ready (Idle) state via

USB or Network port

Special Mode Update1. Power ON with pressing Stop Key2. MFP Set enter the status of Download Mode3. Download F/W to MFP Set via ONLY USB3. After download F/W, MFP Set will conduct Rom

update and also reboot system by itself

Reports (Configuration Report)

The added Items in Tech.Mode-. Send Level-. Dial Mode-. Modem Speed-. Error Rate

Reports (Supplier Info.)

The addes items in Tech.Mode-.Some items in Toner Information

Messages (Printer & Engine)

Service call error

Etc.Invalid Yellow(M/C/K) Toner , Install Yellow(M/C/K) TonerDoor Open , Replace/Install Waste Toner Unit

Paper

Low Heat Error. Cycle Power , Overheat Error. Cycle Power, LSU Motor Error. Cycle Power, LSU Hsync Error. Cycle Power, Open Heat Error. Cycle Power, Main Motor Locked, Fuser Fan Locked

Paper Jam 0. Open/Close Door, Paper Jam 1. Open/Close Door, Paper Jam 2. Check Inside, Paper Mismatch in the Tray 1, Tray 1 Paper Empty

Special Operation

Toner Supply Mode

Altitude

Auto continue

In case of paper mismatch, different paper size between installed paper in tray and user set paper, Printing start after 30 sec if the Auto Continue option is ON state.

To set different printing density as Altitude

When the new toner kit is installed in MFP set, the main motor is running to supply toner - Max. 20sec for each toner - Just One time (new toner)

Tech ModeInstruction

Method of entering service modeMenu->#->1->9->3->4Check F/W versionMenu->#->1->9->3->#

Data Setup

Clear All Mem. Clear Count : Total Page / FLT Scan / Imaging Unit / Transfer Belt /Fuser / TransferRoller / Tray Roller

Report

Machine Test

Switch Test / Dram Test / Rom Test / Shading Test

Configuration / Error Info / Usage Page / Component Check Service Support

Method of checking Error ???• Check ‘Error message’ displayed in Smart Panel (or

LCD) !!!!• Check ‘Error Log’ page to check error history

happened in set !!!• Review ‘Supplies Information Report’ for supplies

problem !!!• Can not send color documents ?• 1. Check supporting color image the other fax machine (Receiving fax)• 2. Check sending fax by On-Hook dial ?

• Check list for communication error in fax ?• 1. Check ‘System Data Report’ ( setup value )• 2. Check Protocol Dump List

• Copy image is poor ??? 1. At first, print Demo Page to check printing quality (If the demo page print out is normal, Printing function is also normal) 2. Print using shading & print and check other strange image in printed data 3. Check pattern (Dirty material , CIS level,….) 4. Check copy setup values

Prob 1) Which one is the best way to send color fax documents ? 1 1. On-Hook dial + Color Start 2. One-Touch dial 3. Speed Dial 4. Digit Dial + Start

Prob 2) Which one is wrong way to check communication error ? 4 1. Check setup values related with FAX in System Data List 2. Check Fax status as reviewing protocol Dump List 3. Check the other Fax (Receive or Send) support communication type 4. Print Demo Page Prob 3) Which one is wrong way to check Copy Quality ? 4 1. At first, print Demo Page to check printing quality (If the demo page print out is normal, Printing function is also normal) 2. Print using shading & print and check other strange image in printed data 3. Check copy setup values 4. Check Fax setup values reviewing system data list