Clover Notch Favored Angle Screws Extensive Implant

Clover Notch™ Favored Angle Screws

Extensive Implant Selection

Streamlined Instrumentation

Certex Spinal Fixation System LogoPMS 2592 Purple & Black


Fixed and variable Cross Connectors available

Clover Notch™ cup provides 4 x 40° favored angle

7.4mm Run-On-Rod

Same Cap is used for Screws, Hooks, and Rod Connectors allowing for a more streamlined technique

3mm above the rod profile for minimal tissue disruption

Screws are self tapping and self drilling

A variety of Laminar Hooks available

Occipital Fixation

Offset Connectors: assist to reduce rod contouring

Rod-to-Rod Connectors: for intraoperative adjustablilty

Wide range of screw diameters and lengths allows for anatomical variation

Surgeon can attain favored angle at four positions due to Clover Notch™ cup

Low locking torque at 35 inch-pounds

Conical shape cap provides multiple point fixation to rod

4 x 40° favored angle provides up to 80° of polyaxial motion

Non-favored angle provides up to 62° of polyaxial motion

Recessed marker gives visual identifier of lead-in thread to minimize cross threading


Lateral Mass Screws

3.5mm 4.0mm 4.5mm

10.4mm

Full Thread Screws

3.5mm 4.0mm

Ratio of smooth shank is the same

for all sizes

Smooth Shank Screws

10.4mm

Occipital Plates

Small (24mm) Medium (30mm) Large (36mm)

Occipital Screws

Screw Diameters 4.5 and 5.5mm6-16mm Lengths

Cervical Hooks Inline Offset Right Offset Left

30º angle

Rods Lengths Available: 30-50mm (5mm increments)

60-100mm (10mm increments)

200mm3.5/5.5mm Transitional Rod 400mm length

Cross Connectors

Variable

Fixed

Sizing variability

3.5mm Rod

Final lock at 35 inch-pounds

Hooks available in 4.5mm and 6.0mm widths

Final lock at 35 inch-pounds

3.5mm Rod

Pre-Bent Rods Lengths 100-500mm

Offset and Rod ConnectorsLateral Offset

ConnectorLeft and Right

Offset Connectors Cable ConnectorParallel

ConnectorAxial/Parallel

Connector

Certex® Screws and Cap

Item# DescriptionX067-0020 3.5mm x 10mm Screw

X067-0021 3.5mm x 12mm Screw

X067-0022 3.5mm x 14mm Screw

X067-0023 3.5mm x 16mm Screw

X067-0024 3.5mm x 18mm Screw

X067-0025 3.5mm x 20mm Screw

X067-0026 3.5mm x 22mm Screw

X067-0250 3.5mm x 16mm Threaded x 8mm Smooth x 24mm Overall Screw






X067-1500 4.0mm x 10mm Screw

X067-1501 4.0mm x 12mm Screw

X067-1502 4.0mm x 14mm Screw

X067-1503 4.0mm x 16mm Screw

X067-1504 4.0mm x 18mm Screw

X067-1505 4.0mm x 20mm Screw

X067-1506 4.0mm x 22mm Screw

X067-1507 4.0mm x 24mm Screw

X067-1508 4.0mm x 26mm Screw

X067-1509 4.0mm x 28mm Screw







X067-0045 4.5mm x 20mm Screw

X067-0047 4.5mm x 24mm Screw

X067-0049 4.5mm x 28mm Screw

X067-0051 4.5mm x 32mm Screw

X067-0053 4.5mm x 36mm Screw

X067-0055 4.5mm x 40mm Screw

X067-0105 Certex Cap

Certex® Rods

Item# DescriptionX067-0370 3.5mm Rod, 30mm

X067-0371 3.5mm Rod, 35mm

X067-0372 3.5mm Rod, 40mm

X067-0373 3.5mm Rod, 45mm

X067-0374 3.5mm Rod, 50mm

X067-0376 3.5mm Rod, 60mm

X067-0378 3.5mm Rod, 70mm

X067-0380 3.5mm Rod, 80mm

X067-0382 3.5mm Rod, 90mm

X067-0384 3.5mm Rod, 100mm

X067-0404 3.5mm Rod, 200mm

X067-0368 3.5mm - 5.5mm Transitional Rod, 400mm

Certex® Cross Connectors

Item# DescriptionX067-0130 Cross Connector, 28-33mm

X067-0131 Cross Connector, 33-42mm

X067-0132 Cross Connector, 42-58mm

X067-0150 Fixed Cross Connector, 22mm



Certex® Hooks

Item# DescriptionX067-1700 Lamina Hook, Inline, 4.5mm

X067-1701 Lamina Hook, Inline, 6.0mm

X067-1710 Lamina Hook, Offset Right, 4.5mm

X067-1711 Lamina Hook, Offset Right, 6.0mm

X067-1720 Lamina Hook, Offset Left, 4.5mm

X067-1721 Lamina Hook, Offset Left, 6.0mm

F-1000.23 Rev C 11/15

X-spine Systems, Inc.452 Alexandersville Rd., Miamisburg, OH 45342

Phone: 800-903-0640 • Direct: 937-847-8400 • Fax: 937-847-8410www.x-spine.com

INDICATIONS: See Package Insert for a more complete listing of indications, contraindications, warnings, precautions, and other important information.

LIMITED WARRANTY and DISCLAIMER: X-spine products have a limited warranty against defects and workmanship and materials. Any other express or implied warranties, including warranties of merchantability or fitness, are disclaimed.

WARNING: In the USA, this product has labeling limitations. See package insert for complete information. CAUTION: USA Law restricts these devices to sale by or on the order of a physician.

X-spineSM, the X-spine logo, CERTEX® and Clover Notch™ are trademarks or servicemarks of X-spine Systems, Inc.Patents Pending.© 2015 X-spine Systems, Inc., All rights reserved.

Certex® System Occipital Set

Item# DescriptionX067-0212 Small Occipital Plate, 24mm

X067-0213 Medium Occipital Plate, 30mm

X067-0214 Large Occipital Plate, 36mm

X067-0220 Occipital, 4.5mm X 6mm screw






















X067-0128 3.5mm Pre-Bent Rod, 300mm x 67º

X067-1680 3.5mm Pre-Bent Rod, 300mm x 90º

Certex® System Connector Set*

Item# DescriptionX067-0170 Straight Lateral Offset Connector, 12mm

X067-0171 Straight Lateral Offset Connector, 17mm

X067-0175 Lateral Offset Connector, Right, 7mm

X067-0177 Lateral Offset Connector, Right, 11mm

X067-0180 Lateral Offset Connector, Left, 7mm

X067-0182 Lateral Offset Connector, Left, 11mm

X067-0185 90° Cable Connector

X067-0201 Axial/Parallel Rod Connector, 3.5mm to 3.5mm

X067-0203 Open Parallel Rod Connector, 3.5mm to 3.5mm


X067-0275 Axial/Parallel Rod Connector, 5.5mm to 5.5mm


X067-1600 3.5mm Continuous Radius Rod, 30mm






*Connectors use Certex® Cap X067-0105

Clover Notch™

cup provides 4 x 40° favored angle

Documents

Clover Notch Favored Angle Screws Extensive Implant