Clarion Co., Ltd. · Power does not turn on. Is power cable connected properly? Check the wiring. Is a fuse blown out? Replace with a fuse of the same amperage (3A). Color is washed-out

Clarion Co., Ltd.All Rights Reserved. Copyright 2012: Clarion Co., Ltd.

Printed in Korea / Gedruckt in Korea / Stampato in Corea / Imprimé en Corée / Impreso en Corea CJ-7100E2012/11

2

En

glish

1. Before Use................................................... 3

2. Features ...................................................... 4

3. Names of the Monitor Buttons ..................... 4

4. Operations of Monitor .................................. 4

5. Names of the Remote Controller Buttons.... 8

6. Operations of Remote Controller................. 8

7. Connections............................................... 12

8. Installation ................................................. 13

9. Troubleshooting......................................... 14

10. Specifications .......................................... 14

Contents

This unit has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation.This unit generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular

installation.If this unit does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to consult the dealer or an experienced radio/TV technician for help.

INFORMATION FOR USERS:CHANGES OR MODIFICATIONS TO THIS PRODUCT NOT APPROVED BY THE MANUFACTURER WILL VOID THE WARRANTY AND WILL VIOLATE FCC APPROVAL.

CJ-7100E-A.book 2 ページ２０１２年９月１８日　火曜日　午後１時５５分

3

En

glish

Warning

Do Not Back Up Vehicle While Relying Only on the Monitor Image Use Slow Speeds When Backing Up The rear-view monitor image has the same right-left inversion as your vehicle’s

rearview mirrors. Depending on the vehicle, the field and angle of view may differ.

Precautions (when you use the monitor) Do not touch the LCD panel. Use the product at the temperature range of -10°C ~ 60°C. Screen may be a little dark when the product is operated in low temperature areas.

Screen will show normal luminosity after a few minutes. Do not disassemble and modify the product in any way.

This may cause fire and/or electric shock.When you install the product in a car and watch monitor, the car engine should be

running as there might occur excessive discharge of the car battery. Any liquid leaking into product may cause malfunction. If alternator noise from the speaker becomes objectionable when listening in AV

MODE, install a ground loop isolator between the AUDIO INPUT and the connected AV component.

Precautions (when you use the product in a car) The driver should not use the product while he/she is driving. Be cautious of humidity and shock when you use the product in a car. Cover the product when exposed to direct rays of the sun for a long period of

time.(You should keep the product at a temperature range of -20°C ~ 70°C.)

1. Before Use


4

En

glish

Application of 7.0" WIDE TFT LCD with high resolution and low reflection All functions are displayed on screen (OSD function) 7 Language Display Selection

(ENGLISH-DEUTSCH-ITALIANO-FRANÇAIS-ESPAñON- - )

Picture quality control (PWM control) Free voltage (From DC12V to DC24V) Dimmer selection function Camera input (2 system) /Work together with back gear/turn signal Video input jack (video/mono audio)Wireless remote controller is included

POWER

2. Features

3. Names of the Monitor Buttons

4. Operations of Monitor

[DIMMER]

[MODE]

[MENU]

STAND BY LED

SENSOR

[UP]

[DOWN]

[POWER]

1

ON OFF (1) Press [POWER] button to on the power.(STAND BY state is OFF)

(2) Press [POWER] button again to off the power.(STAND BY state is ON)


5

En

glish

MODE (Camera/AV Selection)

It is a function to change CAMERA (CAM1/CAM2/AV).

MENU

It is a function to select MAIN MENU (SETUP, PICTURE, CAMERA)(1) Press [MENU] button to select MAIN MENU, changed color in red when it is selected.

• Every time the button is pressed, the setting changes.

(2) Press [MODE] button to select SUB MENU, changed color in red when it is selected. • Every time the button is pressed, the setting changes.

2

CAM1 CAM2 AV

(1) Press [MODE] button.• The characters of CAM1, CAM2 or AV

appear on the screen and they disappear after 5 seconds.

CAM1

Note: In the mirror mode, the character is inverted.

3

SETUP PICTURE CAMERA

DIMMERLANGUAGEDIRECTIONDISPLAYRESET

ENGLISH

WIDE0

CONTRASTBRIGHTNESSCOLORTINT

50

5050

70

SUB MENU

CAM1CAM2 NORMAL

NORMAL

SETUP PICTURE

CAMERA


6

En

glish

SET UP (SUB MENU)

(3) Press [UP]/[DOWN] button to change Settings.

DIMMER

–

• This setting can also be changed by pressing [DIMMER] ( ) button.

LANGUAGE

– – – – –

–

DIRECTION (Inverted upside down)

DISPLAY (Screen size)

RESET A factory default reset will clear all of OSD information

ENGLISH DEUTSCH ITALIANO FRANÇAIS ESPAñON


ENGLISH

WIDE0


ENGLISH

WIDE180

FULL WIDE NORMAL CINEMA


7

En

glish

PICTURE (SUB MENU)


CAMERA (SUB MENU)


In the mirror mode, the screen is inverted laterally.


70

4040

40


40

4070

40


40

7040

40

CONTRAST BRIGHTNESS COLOR


40

4040

50

TINT

CAM1CAM2 NORMAL

NORMAL


8

En

glishPOWER

5. Names of the Remote Controller Buttons

6. Operations of Remote Controller

[POWER]

[DIM]

[DISP]

[MUTE]

[MODE]

[MENU]

[VOL+-]

[ ]

1

(1) Press [POWER] button to on the power.(STAND BY state is OFF)

(2) Press [POWER] button again to off the power.(STAND BY state is ON)

ON OFF


9

En

glish

MODE (Camera/AV Selection)

It is a function to change CAMERA (CAM1/CAM2/AV).

MENU/

It is a function to select MAIN MENU (SETUP, PICTURE, CAMERA)

(2) Press [ ] button to select SUB MENU, changed color in red when it is selected. • Every time the button is pressed, the setting changes.

SET UP (SUB MENU)

(3) Press [ ] button to change Settings.

DIMMER

–

LANGUAGE

– – – – –

–

2

CAM1 CAM2 AV

Note: In the mirror mode, the character is inverted.

(1) Press [MODE] button.• The characters of CAM1, CAM2 or AV

appear on the screen and they disappear after 5 seconds.

CAM1

3 4

SETUP PICTURE CAMERA

(1) Press [MENU] button to select MAIN MENU, changed color in red when it is selected.• Every time the button is pressed, the

setting changes.

ENGLISH DEUTSCH ITALIANO FRANÇAIS ESPAñON


10

En

glish

DIRECTION (Inverted upside down)

DISPLAY (Screen size)

RESET A factory default reset will clear all of OSD information

PICTURE (SUB MENU)


CAMERA (SUB MENU)


In the mirror mode, the screen is inverted laterally.


ENGLISH

WIDE0


ENGLISH

WIDE180



70

4040

40


40

4070

40


40

7040

40

CONTRAST BRIGHTNESS COLOR


40

4040

50

TINT

CAM1CAM2 NORMAL

NORMAL


11

En

glish

VOL +-

DISP

MUTE

DIM

5(1) Press [VOL+] button to turn up the volume.

(2) Press [VOL-] button to turn down the volume.

VOLUME70

VOLUME30

6(1) Press [DISP] button to select the screen

size.


7(1) Press [MUTE] button to mute the sound.

(2) Press [MUTE] button again to cancel.

8(1) Press [DIM] button to change setting.

–


12

En

glish

7. Connections

*3 *3

*2

*2

*1

*1

GREEN (CAMERA2)

ORANGE (CAMERA1)

BLACKGROUND

REDACCESSORY(ACC)DC12V/24V

CAMERA1

CAMERA1(Sold Separately)

CAMERA2(Sold Separately)

*1 Use a Clarion camera.*2 A relay cable, sold separately, is required

for connecting the camera.*3 Use tape to keep the connection between

the monitor cable and the camera relay cable secure.

MONITOR CABLE

CAMERA2

RELAY CABLEYELLOWVIDEO INPUT

WHITEAUDIO INPUT

Please be sure to connect when you connect the camera.ORANGE (CAMERA-1, priority) Standby + (for rear-view)

Connect this cable to “+” of back gear lamp.GREEN (CAMERA-2) Standby + (for side-view)

Connect this cable to “+” of turn signal lamp.


13

En

glish

1. Choose a location where you install the Monitor. Clean the place for the Stand with cleanser

and remove the Protective Tape. And then attach it exactly where you want.

2. Fasten the Monitor with Tapping Screw.

3. Adjust angle of Stand and install Monitor.

4. Connect each connecting cable as in the product installation reference.

8. Installation

Fix Knob (Bracket)

Safeguard tape

Control Knob (Angle)

Stand Base


14

En

glish

Caution: The design and specifications of this product in order to improve its quality may be changed without notice.

9. Troubleshooting

Problem Cause Measure

No image is displayed.Is camera connected properly?

Check the wiring to the camera and the camera connection.

Power does not turn on.

Is power cable connected properly?

Check the wiring.

Is a fuse blown out? Replace with a fuse of the same amperage (3A).

Color is washed-out.Operating environment is inappropriate.

Temperature in the car is below 0°C or over 60°C. Check to see that the temperature in the car is appropriate (around 25°C).

10. Specifications

ITEMSPECIFICATION

NTSC PAL

LCD PANEL

SCREEN SIZE 7 INCH (178.8 mm)

NUMBER OF PIXELS 800(W) x 3(RGB) x 480(H)

DOT PITCH 0.0642(W) x 0.1790(H) mm

BRIGHTNESS 400 cd/m2

DISPLAY AREA 154.08(W) x 85.92(H) mm

CONTRAST RATIO 1:500

VIEW ANGLE (L/R/U/D) 70°/70°/50°/70°

POWER SUPPLY VOLTAGE DC 12V - 24V

CURRENT 450mA (DC 12V, MONITOR SET ONLY)

INPUT SYSTEM AUTO (NTSC/PAL)

FREQUENCY HORIZONTAL 15.734 KHz 15.625 KHz

VERTICAL 60Hz 50Hz

INPUT SIGNALVIDEO SIGNAL COMPOSITE VIDEO SIGNAL

AUDIO SIGNAL MONO SIGNAL 400mVrms

SPEAKER 0.5W MAX

LANGUAGE DISPLAY SELECTION 7 LANGUAGE

USER CONTROLS POWER, MODE, MENU, UP, DOWN, DIMMER

OPERATING TEMPERATURE -10°C ~ + 60°C

STORAGE TEMPERATURE -20°C ~ + 70°C

DIMENSION (W x H x D) 187(W) x 113.5(H) x 26.5(D)

WEIGHT 461g

ACCESSORIES

MONITOR CABLE ASS’Y·······························1

STAND ASS’Y ·············································1

REMOTE CONTROLLER (included with battery)·····1


15

En

glish

MEMO


Clarion Co., Ltd.All Rights Reserved. Copyright 2012: Clarion Co., Ltd.

Printed in Korea / Gedruckt in Korea / Stampato in Corea / Imprimé en Corée / Impreso en Corea CJ-7100E2012/11

Documents

Clarion Co., Ltd. · Power does not turn on. Is power cable connected properly? Check the wiring. Is a fuse blown out? Replace with a fuse of the same amperage (3A). Color is washed-out