Installing Cisco TelePresence System Profile 52” Dual

Page 178-19776-01revB Profile 52 Dual Installation Sheet | April 2012 | © 2010-2012 Cisco Systems, Inc. All rights reserved.

PRECAUTIONS

Please follow the steps in this installation guide when unpacking and assembling Profile 52” Dual.

MANPOWER

A minimum of two (2) persons are required when installing Profile 52” Dual.

UNPACKING THE SYSTEM AT THE DESTINATION

It is highly recommend to start the unpacking and assembling of Profile 52” Dual at the place where it is to be used.

If it is not possible to bring the complete delivery to the room where Profile 52” Dual is to be used, then unpack and bring the smaller units to the destination.

• The monitor box requires two (2) persons to lift 55 kg / 121 lb).

• The bottom module column requires two (2) persons to lift (40 kg / 88 lb).

• The foot module requires two (2) persons to lift (stand-alone: 35 kg / 77 lb; wall-mounting: 20 kg / 44 lb).

INSTALLATION NEAR A SOCKET-OUTLET

The equipment must be installed near a socket-outlet. The socket-outlet shall be easily accessible after installation.

ROOM GUIDELINES

NOTE: The floor must be in level.

The recommended distance between the Profile 52” Dual and the meeting room table should be minimum 1.5 m / 59 in.

Read more about room guidelines in the Video conferencing room primer.

USER DOCUMENTATION

The user documentation for this product, including compliance and safety information, is available on the Cisco web site. Go to: http://www.cisco.com/go/telepresence/docs.

DIMENSIONS OF THE PROFILE 52” DUAL

• Height: 63.8” / 162 cm

• Width: 94.9” / 241 cm

• Depth (wall mounting): 10.2” / 26 cm

• Depth (stand-alone): 17.7” / 45 cm

• Weight: 518 lb / 235 kg

The Profile 52” Dual delivery contains:

Monitor box:

• Two monitors and speaker grilles

Bottom module column

Camera

Touch Screen CS

Foot module box:

• Foot module (stand-alone or wall mounting)

• Four M8×45 screws

• Two wall mounting brackets and four M6×10 screws (for wall mounting only)

• Wrench

• Level adjustment tool (orange)

Monitor back cover box:

• Monitor back cover

• Monitor brackets

• M4×25 and M4×8 screws for the monitor brackets

• Camera bracket

• Wing nuts for the camera bracket

Accessories box:

• Cables

• Microphones, 4 pcs

• Remote control and 4 AAA batteries

• Gloves, 2 pairs

• Cleaning cloth

• Allen key, screwdriver

• Four M8×16 screws

1 Content overview

Remove the outer cover and locate the different boxes as illustrated below.

2 Lift the column out of the package. Mount the column to the foot module to complete the bottom module

Left monitor

Right monitor

Column

Stand-alone foot module

CAUTION

HEAVY

3 WHEN YOU HAVE A WALL MOUNTING FOOT MODULE: Mount the column to the foot module and fasten it to the wall WARNING

Due to the size and weight of this equipment, it is very important that the wall mount unit is safely installed according to the installation instructions and that the wall is able to safely support the product. It is highly recommended that the wall mounted system is installed by trained personnel.

1. Mount the column to the wall mounting foot module, similar to step 2.

2. Fasten the wall brackets to the bottom module with the four M6×10 screws. Use the Allen key.

3. Place the bottom module by the wall, mark where to fasten the bracket and move the bottom module away.

4. Add the suitable fixing device for the screws in the wall, and fasten the bottom module.

FASTEN THE COLUMN TO THE FOOT MODULE

1. Make sure the foot module has been placed at its permanent location.

2. Place the column on the foot module, open the rear door, and remove the door stop bracket.

3. Carefully open the rear door completely.

4. Use four M8×45 screws and fasten the column to the foot module.

5. Mount the door stop bracket back in place.

LEVELLING ADJUSTMENT

Make sure the unit is stable.

Place the orange level adjustment tool on the foot wheel under the foot module for height adjustment.

Seen from above, turn clockwise to adjust the height up. Use the opposite side of the tool and turn counterclockwise to adjust down.

Grab here when lifting the column.

CAUTION

HEAVY

CAUTION

HEAVY

Rev. Date Prep. Checked Change

---

Telecom AS ---------

---------Part weight:

Sheet size:Scale:

Surface treatmentSpecification: MaterialTolerances

Unit:

Europeanprojection

Sheet 1 of 1

All materials, finishes, and proccessesmust comply with the RoHS directives

Dimensions without paint or finish

Flame class requirement: -

ProcessesType:Manufacturer:Type number:Thickness:Color:Surface:Glossiness:Flame class:UL reference:3D CAD model file 120601 rev. 03 is master

Packaging Kit Profile 52" Dual120601 rev.

71743g

A3mm

1:8

Monitor back cover and monitor brackets

Right and left monitor

Bottom module column

Camera

Foot module

Accessories box4 * M8×45

Allen key

Touch screen

Use the wrench to remove the door stop bracket on the rear door before fastening the column to the foot module.

Rear side

Door stop bracket

Fasten the column to the foot module.

Fasten the column to the foot module.

Access the innermost screws from these holes.

The bottom module is viewed from the rear side.

Add the suitable fixing device for the screws in the wall.

The wall

4 * M6×10

Allen key

The monitors come in a separate box. The monitor box contains monitors and speaker grilles for the monitors. Remove the lid and locate the left and right monitor and the speaker grilles.

Unpacking and assembling Profile 52” Dual

CAUTION

HEAVY

EMC A Class declaration

Installing Cisco TelePresence System Profile 52” Dual

Page 278-19776-01revB Profile 52 Dual Installation Sheet | April 2012 | © 2010-2012 Cisco Systems, Inc. All rights reserved.

6 Mounting the camera cables and the camera

MOUNTING THE CAMERA CABLES

1. Locate the camera cables in the bottom module (the two long cables).

2. Locate the hole in the monitor where the cables can be pushed through. Push the cables through the hole in the right monitor.

3. On the rear side, place the cables in the foam rails that are going on the rear side of the monitor.

CAMERA CABLE CONFIGURATION PrecisionHD 1080p

HDMIRJ45

For countries with 60 Hz current frequency you must set the PrecisionHD 1080p camera DIP switch to: 00100.

MOUNTING THE CAMERA

1. Connect the RJ45 and HDMI cables to the camera, see illustration.

2. Loosen the wing nuts on the camera bracket and move the bracket to the rear position.

3. Place the camera on the bracket and slide the bracket with the camera towards the front and tighten the wing nuts.

4. Place the camera cables in the foam rails.

Upper monitor bracket

Camera bracket

Lower monitor bracket*

MOUNTING THE CAMERA BRACKET

1. Fasten the camera bracket using two wing nuts.

* The lower monitor bracket is not used on a wall mounted system. Instead, make sure the monitors are aligned at the front.

8 Connect the system

Ethernet cable

PC cable

Microphone cablePower cable

1. Open the rear door and route the cables out through the opening at the lower part of the door.

2. Close the rear door carefully.

3. Place the microphones on the table, connect the microphone cables and place the PC cable on the table.

4. Connect the Ethernet cable.

5. Connect the power cable, use the country specific power cable that came with the system.

6. Open the front door and turn on the monitor.

7. Follow the instructions in the accompanying Touch Screen CS installation guide to connect and initialize the touch screen.

8. The system should be up and running in a few minutes.

The rear door

5 Connect the monitor cables to the left and right monitor

Connect the left monitor:

1. HDMI cable

2. Speaker in (15 pin DSUB from DNAM)

3. Power cable

Left monitor connectorsB

B

Right monitor connectors

Connect the right monitor:

1. HDMI cable

2. Speaker in (15 pin DSUB from DNAM)

3. Power cable

CONNECTING MONITOR CABLES

Open the front door and locate the monitor connectors and cables.

4 Unpack the monitor box and lift out the monitors. Fasten the monitors to the bottom module and mount the camera bracket

LIFTING HANDLES. Locate the orange lifting handles in the front and rear side of the monitor.

MOUNTING THE MONITORS

1. Carefully lift the right monitor out of the packaging as illustrated.

2. See the two triangle holes in the monitor base. Use these holes to help steering the monitor to enter the poles on the column.

3. Repeat the above procedure for the left monitor.

Right monitor

Left monitor

See the two triangular holes in the base. Use the holes to help steering the monitor to enter the poles on the column.

4 * M8×16

Allen key

Unpack the monitor box.

Speaker grille box

Lift out to open the snap lockers.

CAUTION

HEAVY

7 Finishing up

MOUNTING THE BACK COVER

1. Enter the back cover on top and snap it on place with the magnets.

2. Remove the plastic cover in front of the monitor.

3. Remove the plastic foil on the monitor frame.

4. Snap on the speaker grille to the front.

5. Use the supplied cloth to clean the system.

The magnets are strong. Make sure your fingers are not trapped.

Power HDMI 1 Speaker in

PowerHDMI 1 Speaker in

MOUNTING THE MONITORS, continued

4. Align the monitors at the top and fasten the two monitors together using the upper monitor bracket and the M4×25 screws.

5. Fasten the two monitors together at the bottom using the lower monitor bracket and the M4×8 screws.

6. Fasten the monitor to the column poles using four M8×16 screws, two screws at each monitor.

7. Tighten the monitor gently to the bottom module until the monitor cannot be moved anymore.

EMC Class A declaration

WARNING: This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

A级声明 (A Class product declaration)

本产品为 A级 ITE，在其使用说明，铭牌等显著位置中已包含如下内容的声明

(We declare here that the subject product is A class ITE product, and the

following statement is clearly marked in the user manual or nameplate):

声明所在位置 (Position of the Declaration): 使用说明 User Manual

铭牌 Nameplate

申请号 (Application No.)：

申请人 (Applicant):

型号 (Model Number)：

签字/盖章 Signature/Stamp:

日期 Date:

警告

此为 A级产品。在生活环境中，该产品可能会造成无线电干扰。在这种

情况下，可能需要用户对干扰采取切实可行的措施。

WARNING:

This is a class A product. In a domestic environment this

product may cause radio interference in which case the user may be

required to take adequate measures.

B

B