Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) · Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) First Published: 2016-02-22 Last Modified: 2016-11-18

Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)First Published: 2016-02-22

Last Modified: 2016-11-18

Americas HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706USAhttp://www.cisco.comTel: 408 526-4000 800 553-NETS (6387)Fax: 408 527-0883

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS,INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND,EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITEDWARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITHTHE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY,CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB's public domain versionof the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.

NOTWITHSTANDINGANYOTHERWARRANTYHEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS"WITH ALL FAULTS.CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OFMERCHANTABILITY, FITNESS FORA PARTICULAR PURPOSEANDNONINFRINGEMENTORARISING FROMACOURSEOFDEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUTLIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERSHAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, networktopology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentionaland coincidental.

This product includes cryptographic software written by Eric Young ([email protected]).

This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.openssl.org/)This product includes software written by Tim Hudson ([email protected]).

Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: http://www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnershiprelationship between Cisco and any other company. (1110R)

Please send general FSF & GNU inquiries to [email protected]. There are also other ways to contact the FSF. Please send broken links and other corrections or suggestions [email protected]. Please see the Translations README for information on coordinating and submitting translations of this article.

Copyright © 2007, 2009, 2011 Free Software Foundation, Inc. Verbatim copying and distribution of this entire article are permitted worldwide, without royalty, in any medium, providedthis notice, and the copyright notice, are preserved. Updated: Date: 2011/06/28 02:44:32

© 2016 Cisco Systems, Inc. All rights reserved.

http://www.openssl.org/

http://www.cisco.com/go/trademarks

http://www.cisco.com/go/trademarks

mailto:[email protected]

http://www.gnu.org/contact/


http://www.gnu.org/server/standards/README.translations.html

C O N T E N T S

P r e f a c e Preface xli

Audience xli

Document Conventions xli

Related Documentation xliii

Documentation Feedback xliii

C H A P T E R 1 A Commands 1

aaa authentication login console 3

aaa authentication login default 4

aaa authentication login domain 5

aaa banner 6

aaa group server ldap 7

aaa group server radius 8

aaa group server tacacsplus 9

aaa scvmm-certificate 10

aaa user default-role 11

absolute 12

access-group 13

access-list 14

account-status 15

action 16

address-family 17

address 19

admin-state-enable 20

admin 22

advertise-subnet 23

aggregate-address 24

Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) iii

allow-origin 25

allow-self-as 26

allow-writes 27

allowed-self-as-count 28

application 29

area default-cost 30

area l3out 31

area loopback 32

area nssa 33

area nssa default-information-originate 34

area nssa no-redistribute 35

area nssa translate 36

area range 37

area route-map 38

area stub 39

arp flooding 40

asn 41

attribute 42

attribute match custom 43

attribute match datacenter 44

attribute match domain 45

attribute match guest-os 46

attribute match hypervisor-id 47

attribute match ip 48

attribute match mac 49

attribute match vm-id 50

attribute match vm-name 51

attribute match vnic 52

authenticate 53

authentication-key 54

auto-cost 55

autonomous-system 56

C H A P T E R 2 B Commands 57

bandwidth 58

Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)iv

Contents

basedn 59

bash 60

bfd 61

bfd ip ipv6 authentication 62

bfd ip ipv6 inherit 64

bfd ip ipv6 tenant 65

bgp 66

binddn 67

bpdu-filter 68

bridge-domain 69

C H A P T E R 3 C Commands 71

callhome 73

catalog-version 74

cdp 75

cert-chain 78

cert 79

certificate 80

channel-group 81

channel-mode 83

ciphers 86

clear-encryption-key 87

clear-pwd-history 88

clear endpoints 89

clear snapshot file 90

clear snapshot job 91

clear techsupport controllers 92

clear techsupport switch 93

clear troubleshoot epext session report 94

clear troubleshoot eptoep session report 95

clock display-format 96

clock show-offset 97

clock timezone 98

cluster-device 99

cluster-device query-device-health 100

Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) v

Contents

cluster-device query-device-statistics 101

cluster-device query-device-validation 102

cluster-interface 103

comm-policy 104

configure-avs 105

configure-dvs 106

configure 107

connection intra service 108

connection terminal 109

connector 110

console 111

contract-id 112

contract 113

contract consumer 114

contract deny 117

contract enforce 119

contract provider 120

controller-group 123

controller 124

cost 125

country 126

crypto aes 127

crypto ca 128

crypto keyring 129

crypto webtoken 130

csr 131

customer-id 132

C H A P T E R 4 D Commands 133

data 135

dead-interval 136

debug log reset 137

debug log set 138

decommission controller 139

decommission switch 140

Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)vi

Contents

default-information 141

default-originate 142

deploy-epg tenant application epg type 143

deploy-epg tenant application epg vlan 144

deployment-mode 145

descr 146

description 147

destination-profile 160

destination 161

destination destip 163

destination interface 164

destination tenant 165

dhcp option 167

dhcp relay policy 168

dhparam 169

direction 170

disable-connected-check 173

disable-peer-as-check 174

distance 175

dns 177

dnssearchsuffix 178

dnsservers 179

dnssuffix 180

domain 181

dsr-vip 182

dsr 183

C H A P T E R 5 E Commands 185

ebgp-multihop 187

echo-address 188

echo-mode 189

echo-rx-interval 190

email-addr 191

email-contact 192

email 193

Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) vii

Contents

enable-ssl 194

encryption 195

end 196

endpoint 197

endpoint loop-detect action bd-learn-disable 198

endpoint loop-detect action port-disable 199

endpoint loop-detect enable 200

endpoint loop-detect factor 201

endpoint loop-detect interval 202

endpoint move-detection 203

endpoint retention bounce-age-interval 204

endpoint retention hold-interval 205

endpoint retention local-age-interval 206

endpoint retention move-frequency 207

endpoint retention policy 208

endpoint retention remote-age-interval 209

enforce-subnet-learning 210

epg 211

eraseconfig 212

errdisable recovery cause bpduguard 213

errdisable recovery cause ep-move 214

errdisable recovery cause mcp-loop 215

errdisable recovery interval 216

erspan-id 217

exec 219

exit 220

expiration 221

expires 222

export 223

external-l2 224

external-l3 225

external-l3 epg 226

C H A P T E R 6 F Commands 227

fabric clear 228

Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)viii

Contents

fabric show 229

fex-interface-group 230

fex-profile 231

fex 232

file 233

filter 234

filter tenant bd 236

filter tenant vrf 237

firewall-logging 238

firewall 239

firmware-version 240

firmware 241

firmware repository add 242

firmware repository delete 243

firmware upgrade controller-group 244

firmware upgrade switch-group 245

first-file 246

first-name 247

format 248

C H A P T E R 7 G Commands 249

graceful-restart-helper 250

graceful-restart 251

group 252

C H A P T E R 8 H Commands 253

hello-interval 254

http 255

https 256

C H A P T E R 9 I Commands 257

inband-mgmt 261

inband-mgmt epg 262

inherit 263

inherit bgp address-family 266

Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) ix

Contents

inherit bgp dampening 267

inherit eigrp 268

inherit ipv4 269

inherit ipv6 270

instance 272

interface 273

interface ethernet 275

interface inband-mgmt0 276

interface mgmt0 277

interface port-channel 278

interface vlan 279

interface vpc 280

ip 281

ip address-range 282

ip address 284

ip address tenant application 287

ip address tenant external-l2 289

ip address tenant external-l3 291

ip bandwidth 293

ip bfd 295

ip dhcp relay address tenant application 297

ip dhcp relay address tenant external-l2 298

ip dhcp relay address tenant external-l3 299

ip distribute-list eigrp 300

ip dscp 301

ip hello-interval 303

ip hold-interval 305

ip igmp snooping fast-leave 307

ip igmp snooping last-member-query-interval 308

ip igmp snooping optimise-multicast-flood 309

ip igmp snooping policy 310

ip igmp snooping querier 311

ip igmp snooping query-interval 312

ip igmp snooping query-max-response-time 313

ip igmp snooping startup-query-count 314

Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)x

Contents

ip igmp snooping startup-query-interval 315

ip next-hop-self 316

ip ospf authentication-key 318

ip ospf authentication 319

ip ospf bfd 320

ip ospf cost 321

ip ospf dead-interval 322

ip ospf hello-interval 323

ip ospf inherit 324

ip ospf mtu-ignore 325

ip ospf network 326

ip ospf passive-interface 327

ip ospf prefix-suppression 328

ip ospf priority 329

ip ospf retransmit-interval 330

ip ospf transmit-delay 331

ip passive-interface 332

ip prefix-list 334

ip prefix-list permit le 335

ip router eigrp 336

ip router ospf default 337

ip shared address consumer 338

ip shared address provider 339

ip split-horizon 340

ip summary-address eigrp 342

ip throughput-delay 343

ip ttl 345

iprange 347

ipv6 348

ipv6 address-range 349

ipv6 address 351

ipv6 address tenant application 354

ipv6 address tenant external-l2 356

ipv6 address tenant external-l3 358

ipv6 bandwidth 360

Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) xi

Contents

ipv6 bfd 361

ipv6 dhcp relay address tenant application 362

ipv6 dhcp relay address tenant external-l2 363

ipv6 dhcp relay address tenant external-l3 364

ipv6 distribute-list eigrp 365

ipv6 hello-interval 366

ipv6 hold-interval 367

ipv6 link-local 368

ipv6 nd hop-limit 370

ipv6 nd managed-config-flag 372

ipv6 nd mtu 374

ipv6 nd ns-interval 376

ipv6 nd ns-retries 378

ipv6 nd other-config-flag 380

ipv6 nd policy 382

ipv6 nd prefix 383

ipv6 nd ra-interval 385

ipv6 nd ra-lifetime 387

ipv6 nd reachable-time 389

ipv6 nd retrans-timer 391

ipv6 nd suppress-ra-mtu 393

ipv6 nd suppress-ra 395

ipv6 next-hop-self 397

ipv6 ospf bfd 398

ipv6 ospf cost 399

ipv6 ospf dead-interval 400

ipv6 ospf hello-interval 401

ipv6 ospf inherit 402

ipv6 ospf mtu-ignore 403

ipv6 ospf network 404

ipv6 ospf passive-interface 405

ipv6 ospf prefix-suppression 406

ipv6 ospf priority 407

ipv6 ospf retransmit-interval 408

ipv6 ospf transmit-delay 409

Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)xii

Contents

ipv6 passive-interface 410

ipv6 router eigrp 411

ipv6 router ospf default 412

ipv6 shared address consumer 413

ipv6 shared address provider 414

ipv6 split-horizon 415

ipv6 throughput-delay 416

isis 418

isolation 419

C H A P T E R 1 0 K Commands 421

key 422

C H A P T E R 1 1 L Commands 423

l2-unknown-unicast 425

l3-unknown-multicast 426

l3out 427

l4l7-peer 428

l4l7 429

l4l7 cluster import-from 430

l4l7 cluster name 431

l4l7 graph 432

label match 433

label name 434

lacp fast-select-hot-standby 435

lacp graceful-convergence 436

lacp load-defer 437

lacp max-links 438

lacp min-links 440

lacp port-priority 442

lacp port-priority interface 444

lacp rate 445

lacp rate fast normal interface 447

lacp suspend-individual 448

last-name 449

Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) xiii

Contents

ldap-server attribute 450

ldap-server basedn 451

ldap-server filter 452

ldap-server host 453

ldap-server retries 454

ldap-server timeout 455

leaf-group 456

leaf-interface-group 457

leaf-interface-profile 458

leaf-policy-group 459

leaf-profile 460

leaf 461

legacy 462

link 463

lldp 466

lldp holdtime 469

lldp reinit 470

lldp timer 471

local-as 472

locality 473

logfile 474

logging 475

logging audit 476

logging description 477

logging event 478

logging fault 479

logging server-group 480

logging session 481

logging severity 482

lsp-fast-flood 484

lsp-gen-interval 485

lsp-mtu 486

C H A P T E R 1 2 MCommands 487

mac-address 489

Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)xiv

Contents

match 491

match arp 492

match bridge-domain 493

match community 494

match icmp 495

match ip 496

match ipv6 497

match prefix-list 498

match raw 499

match tcp 500

match udp 501

max-lsa 502

max-validity-period 503

max concurrent 504

max running 505

maximum-paths 506

maximum-prefix 508

mcp 509

mcp action 511

mcp enable 512

mcp factor 513

mcp init-delay 514

mcp transmit-frequency 515

member 516

message-level 517

message-size 518

metric 519

mgmt-epg 520

microsoft-domain 521

microsoft 522

min-rx 523

min-tx 524

min 525

mode 526

modulus 527

Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) xv

Contents

monitor 528

monitor access 529

monitor fabric 530

monitor tenant 531

monitor virtual 532

mtu-ignore 533

mtu 534

multi-destination 537

multi-site-mac-address 538

multicast-address 539

multiplier 540

C H A P T E R 1 3 N Commands 541

name-lookup 542

negotiate 543

neighbor 545

network 546

next-hop-self 547

ntp 548

C H A P T E R 1 4 O Commands 549

oob-mgmt 550

oob-mgmt epg 551

optimize 552

option 553

org-name 554

org-unit-name 555

C H A P T E R 1 5 P Commands 557

passive-interface 559

passphrase 560

password 561

password change-count 563

password change-during-interval 564

password change-interval 565

Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)xvi

Contents

password history-count 566

password no-change-interval 567

password pwd-strength-check 568

path 569

peer-dead-interval 570

periodic-inventory notification 571

phone-contact 572

phone 573

pod 574

policy-group 575

policy-map 577

policy-map type data-plane 578

policy-map type qos 579

port 580

porttrack delay 583

porttrack minlinks 584

porttrack state 585

power 586

prefix-suppression 587

preview 588

priority 589

priv-type 590

priv 591

private-as-control 592

protocol 593

pwd-lifetime 594

C H A P T E R 1 6 Q Commands 595

qos parameters 596

qos preserve 597

query-cluster-health 598

query-cluster-statistics 599

query-cluster-validation 600

query-profile 601

query 602

Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) xvii

Contents

queue control 603

queue limit 604

C H A P T E R 1 7 R Commands 605

radius-server host 607

radius-server retries 608

radius-server timeout 609

rbac role 610

rbac rule 611

rbac security-domain 612

realm 613

recurring 614

redirect 615

redistribute 616

redundancy-mode 617

region 618

reload controller 619

reload switch 620

remote-as 621

remote 622

request-status-count 624

reset-to-factory 625

response-incl 626

response-subtree 627

retransmit-interval 628

retries 629

revision 630

role 631

route-map 632

route-profile 633

route-reflector 634

router-id 635

router bgp 636

router eigrp 637

router ospf 638

Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)xviii

Contents

rtr-cfg 639

run-mode 640

C H A P T E R 1 8 S Commands 641

schedule 661

scheduler 662

scheduling 663

scope 664

scvmm 665

second-file 666

security-domain 667

security 668

send-community 669

server 670

service-policy 673

service 676

session-record-flags 677

set 678

set burst 680

set cir 681

set community 682

set conform-cos-transmit 685

set conform-dscp-transmit 686

set conform 687

set dampening 688

set dscp 689

set exceed-cos-transmit 690

set exceed-dscp-transmit 691

set exceed 692

set excessive-burst 693

set local-preference 694

set metric-type 696

set metric 698

set mode 700

set pir 701

Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) xix

Contents

set qos-class 702

set tag 703

set target-dscp 705

set type 706

set violate-cos-transmit 707

set violate-dscp-transmit 708

set violate 709

set weight 710

shellinabox 712

show aaa authentication 713

show aaa groups 714

show access-list 715

show accounting log 716

show application 717

show audits 718

show audits tenant 719

show audits tenant application 720

show audits tenant application epg 721

show audits tenant bridge-domain 722

show audits tenant bridge-domain detail 723

show audits tenant interface bridge-domain 724

show audits tenant interface bridge-domain detail 725

show audits tenant vrf 726

show audits tenant vrf detail 727

show audits tenant vrf external-l3 bgp 728

show audits tenant vrf external-l3 bgp node 729

show audits tenant vrf external-l3 eigrp 730

show audits tenant vrf external-l3 eigrp detail 731

show audits tenant vrf external-l3 epg 732

show audits tenant vrf external-l3 epg detail 733

show audits tenant vrf external-l3 epg name 734

show audits tenant vrf external-l3 epg name detail 735

show audits tenant vrf external-l3 interfaces 736

show audits tenant vrf external-l3 interfaces detail 737

show audits tenant vrf external-l3 ospf 738

Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)xx

Contents

show audits tenant vrf external-l3 ospf detail 739

show audits tenant vrf external-l3 static-route 740

show audits tenant vrf external-l3 static-route detail 741

show audits tenant vrf external-l3 static-route node 742

show audits tenant vrf external-l3 static-route node detail 743

show bridge-domain 744

show bridge-domain detail 745

show callhome 746

show callhome common destination-profile 747

show callhome common query-profile 748

show callhome common transport-email 749

show catalog 750

show cli command 751

show cli internal audit 752

show cli internal transaction 753

show cli list 754

show cli manpage 755

show cli path 756

show clock 757

show communication ciphers 758

show communication http 759

show communication https 760

show communication shellinabox 761

show communication ssh-service 762

show communication telnet 763

show communication web-requests 764

show contract-type 765

show contract 766

show controller 767

show controller detail 768

show cores 769

show debug counter 770

show debug log 771

show dns-address 772

show dns-domain 773

Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) xxi

Contents

show endpoints 774

show endpoints leaf interface ethernet 775

show endpoints leaf interface port-channel 776

show endpoints vpc 777

show epg 778

show epg detail 779

show events 780

show events controller 781

show events controller detail 782

show events leaf 783

show events leaf fex 784

show events leaf fex module 785

show events leaf interface ethernet 786

show events leaf interface l3instance 787

show events leaf interface mgmt 788

show events leaf interface portchannel 789

show events leaf interface tunnel 790

show events leaf inventory chassis 791

show events leaf inventory fans 792

show events leaf inventory module 793

show events leaf inventory module fabricport 794

show events leaf inventory module leafport 795

show events leaf inventory powersupply 796

show events leaf inventory supervisor 797

show events leaf protocol 798

show events leaf vpc 799

show events leaf vrf 800

show events spine 801

show events spine interface ethernet 802

show events spine interface l3instance 803

show events spine interface mgmt 804

show events spine interface tunnel 805

show events spine inventory chassis 806

show events spine inventory fabric 807

show events spine inventory fans 808

Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)xxii

Contents

show events spine inventory module 809

show events spine inventory module fabricport 810

show events spine inventory powersupply 811

show events spine inventory supervisor 812

show events spine inventory system 813

show events spine protocol 814

show events spine vrf 815

show events tenant 816

show events tenant application 817

show events tenant application epg 818

show events tenant bridge-domain 819

show events tenant bridge-domain detail 820

show events tenant endpoints 821

show events tenant endpoints leaf interface ethernet 822

show events tenant endpoints leaf interface port-channel 823

show events tenant endpoints vpc 824

show events tenant interface bridge-domain 826

show events tenant interface bridge-domain detail 827

show events tenant vrf 828

show events tenant vrf detail 829

show events tenant vrf external-l3 bgp 830

show events tenant vrf external-l3 bgp node 831

show events tenant vrf external-l3 eigrp 832

show events tenant vrf external-l3 eigrp detail 833

show events tenant vrf external-l3 epg 834

show events tenant vrf external-l3 epg detail 835

show events tenant vrf external-l3 epg name 836

show events tenant vrf external-l3 epg name detail 837

show events tenant vrf external-l3 interfaces 838

show events tenant vrf external-l3 interfaces detail 839

show events tenant vrf external-l3 ospf 840

show events tenant vrf external-l3 ospf detail 841

show events tenant vrf external-l3 route-map 842

show events tenant vrf external-l3 route-map detail 843

show events tenant vrf external-l3 static-route 844

Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) xxiii

Contents

show events tenant vrf external-l3 static-route detail 845

show events tenant vrf external-l3 static-route node 846

show events tenant vrf external-l3 static-route node detail 847

show external-l2 epg 848

show external-l2 epg name 849

show external-l2 epg tenant 850

show external-l3 bgp 851

show external-l3 bgp tenant 852

show external-l3 bgp tenant vrf 853

show external-l3 bgp tenant vrf node 854

show external-l3 eigrp 855

show external-l3 eigrp detail 856

show external-l3 eigrp node 857

show external-l3 eigrp node detail 858

show external-l3 eigrp tenant 859

show external-l3 eigrp tenant detail 860

show external-l3 eigrp tenant vrf 861

show external-l3 eigrp tenant vrf detail 862

show external-l3 eigrp tenant vrf node 863

show external-l3 eigrp tenant vrf node detail 864

show external-l3 epg 865

show external-l3 epg detail 866

show external-l3 epg name 867

show external-l3 epg name detail 868

show external-l3 epg tenant 869

show external-l3 epg tenant detail 870

show external-l3 epg tenant vrf 871

show external-l3 epg tenant vrf detail 872

show external-l3 interfaces 873

show external-l3 interfaces detail 874

show external-l3 interfaces node 875

show external-l3 interfaces node detail 876

show external-l3 interfaces tenant 877

show external-l3 interfaces tenant detail 878

show external-l3 interfaces tenant vrf 879

Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)xxiv

Contents

show external-l3 interfaces tenant vrf detail 880

show external-l3 interfaces tenant vrf node 881

show external-l3 interfaces tenant vrf node detail 882

show external-l3 ospf 883

show external-l3 ospf detail 884

show external-l3 ospf node 885

show external-l3 ospf node detail 886

show external-l3 ospf tenant 887

show external-l3 ospf tenant detail 888

show external-l3 ospf tenant vrf 889

show external-l3 ospf tenant vrf detail 890

show external-l3 ospf tenant vrf node 891

show external-l3 ospf tenant vrf node detail 892

show external-l3 route-map 893

show external-l3 route-map detail 894

show external-l3 route-map name 895

show external-l3 route-map name detail 896

show external-l3 route-map tenant 897

show external-l3 route-map tenant detail 898

show external-l3 route-map tenant vrf 899

show external-l3 route-map tenant vrf detail 900

show external-l3 route-map tenant vrf node 901

show external-l3 route-map tenant vrf node detail 902

show external-l3 static-route 903

show external-l3 static-route detail 904

show external-l3 static-route node 905

show external-l3 static-route node detail 906

show external-l3 static-route tenant 907

show external-l3 static-route tenant detail 908

show external-l3 static-route tenant vrf 909

show external-l3 static-route tenant vrf detail 910

show external-l3 static-route tenant vrf node 911

show external-l3 static-route tenant vrf node detail 912

show fabric-recovery status 913

show faults 914

Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) xxv

Contents

show faults controller 916

show faults controller detail 917

show faults l4l7-cluster 918

show faults l4l7-graph 919

show faults leaf 920

show faults leaf fex 921

show faults leaf fex module 922

show faults leaf interface ethernet 923

show faults leaf interface l3instance 924

show faults leaf interface mgmt 925

show faults leaf interface portchannel 926

show faults leaf interface tunnel 927

show faults leaf inventory chassis 928

show faults leaf inventory fans 929

show faults leaf inventory module 930

show faults leaf inventory module fabricport 931

show faults leaf inventory module leafport 932

show faults leaf inventory powersupply 933

show faults leaf inventory supervisor 934

show faults leaf protocol 935

show faults leaf vpc 936

show faults leaf vrf 937

show faults microsoft domain 938

show faults microsoft domain name 939

show faults microsoft domain name hyperv 940

show faults microsoft domain name port-group 941

show faults microsoft domain name scvmm 942

show faults microsoft domain name vm 943

show faults microsoft domain name vm name 944

show faults spine 945

show faults spine interface ethernet 946

show faults spine interface l3instance 947

show faults spine interface mgmt 948

show faults spine interface tunnel 949

show faults spine inventory chassis 950

Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)xxvi

Contents

show faults spine inventory fabric 951

show faults spine inventory fans 952

show faults spine inventory module 953

show faults spine inventory module fabricport 954

show faults spine inventory powersupply 955

show faults spine inventory supervisor 956

show faults spine inventory system 957

show faults spine protocol 958

show faults spine vrf 959

show faults tenant 960

show faults tenant application 961

show faults tenant application epg 962

show faults tenant bridge-domain 963

show faults tenant bridge-domain detail 964

show faults tenant interface bridge-domain 965

show faults tenant interface bridge-domain detail 966

show faults tenant vrf 967

show faults tenant vrf detail 968

show faults tenant vrf external-l3 bgp 969

show faults tenant vrf external-l3 bgp node 970

show faults tenant vrf external-l3 eigrp 971

show faults tenant vrf external-l3 eigrp detail 972

show faults tenant vrf external-l3 epg 973

show faults tenant vrf external-l3 epg detail 974

show faults tenant vrf external-l3 epg name 975

show faults tenant vrf external-l3 epg name detail 976

show faults tenant vrf external-l3 interfaces 977

show faults tenant vrf external-l3 interfaces detail 978

show faults tenant vrf external-l3 ospf 979

show faults tenant vrf external-l3 ospf detail 980

show faults tenant vrf external-l3 static-route 981

show faults tenant vrf external-l3 static-route detail 982

show faults tenant vrf external-l3 static-route node 983

show faults tenant vrf external-l3 static-route node detail 984

show faults vmware domain 985

Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) xxvii

Contents

show faults vmware domain name 986

show faults vmware domain name epg 987

show faults vmware domain name esx 988

show faults vmware domain name port-group 989

show faults vmware domain name vcenter 990

show faults vmware domain name vm 991

show faults vmware domain name vm name 992

show firmware repository 993

show firmware repository detail 994

show firmware upgrade status 995

show firmware upgrade status controller-group 996

show firmware upgrade status controller-group detail 997

show firmware upgrade status detail 998

show firmware upgrade status switch-group 999

show firmware upgrade status switch-group detail 1000

show health 1001

show health l4l7-cluster 1002

show health l4l7-graph 1003

show health leaf 1004

show health leaf fex 1005

show health leaf fex module 1006

show health leaf interface ethernet 1007

show health leaf interface l3instance 1008

show health leaf interface mgmt 1009

show health leaf interface portchannel 1010

show health leaf interface tunnel 1011

show health leaf inventory chassis 1012

show health leaf inventory fans 1013

show health leaf inventory module 1014

show health leaf inventory module fabricport 1015

show health leaf inventory module leafport 1016

show health leaf inventory powersupply 1017

show health leaf inventory supervisor 1018

show health leaf protocol 1019

show health leaf vpc 1020

Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)xxviii

Contents

show health leaf vrf 1021

show health spine 1022

show health spine interface ethernet 1023

show health spine interface l3instance 1024

show health spine interface mgmt 1025

show health spine interface tunnel 1026

show health spine inventory chassis 1027

show health spine inventory fabric 1028

show health spine inventory fans 1029

show health spine inventory module 1030

show health spine inventory module fabricport 1031

show health spine inventory powersupply 1032

show health spine inventory supervisor 1033

show health spine inventory system 1034

show health spine protocol 1035

show health spine vrf 1036

show health tenant 1037

show health tenant application 1038

show health tenant application epg 1039

show health tenant bridge-domain 1040

show health tenant bridge-domain detail 1041

show health tenant interface bridge-domain 1042

show health tenant interface bridge-domain detail 1043

show health tenant vrf 1044

show health tenant vrf detail 1045

show health tenant vrf external-l3 bgp 1046

show health tenant vrf external-l3 bgp node 1047

show health tenant vrf external-l3 eigrp 1048

show health tenant vrf external-l3 eigrp detail 1049

show health tenant vrf external-l3 epg 1050

show health tenant vrf external-l3 epg detail 1051

show health tenant vrf external-l3 epg name 1052

show health tenant vrf external-l3 epg name detail 1053

show health tenant vrf external-l3 interfaces 1054

show health tenant vrf external-l3 interfaces detail 1055

Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) xxix

Contents

show health tenant vrf external-l3 ospf 1056

show health tenant vrf external-l3 ospf detail 1057

show health tenant vrf external-l3 static-route 1058

show health tenant vrf external-l3 static-route detail 1059

show health tenant vrf external-l3 static-route node 1060

show health tenant vrf external-l3 static-route node detail 1061

show inband-mgmt 1062

show inband-mgmt controller 1063

show inband-mgmt switch 1064

show interface bridge-domain 1065

show interface bridge-domain detail 1066

show ip interface bridge-domain 1067

show ipv6 interface bridge-domain 1068

show l4l7-cluster 1069

show l4l7-graph 1070

show l4l7-package 1071

show ldap-server 1072

show locator-led 1073

show locator-led status leaf 1074

show microsoft domain 1075

show microsoft domain name 1076

show microsoft domain name hyperv 1077

show microsoft domain name port-group 1078

show microsoft domain name scvmm 1079

show microsoft domain name vm 1080

show microsoft domain name vm name 1081

show microsoft vm 1082

show monitor access 1083

show monitor fabric 1084

show monitor tenant 1085

show monitor virtual 1086

show ntpq 1087

show oob-mgmt 1088

show oob-mgmt controller 1089

show oob-mgmt switch 1090

Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)xxx

Contents

show policy-map 1091

show policy-map type data-plane 1092

show policy-map type qos 1093

show port-channel leaf 1094

show port-channel map 1095

show port-channel map leaf 1096

show radius-server 1097

show resource 1098

show resource conflict encap-vlan epg 1099

show resource conflict encap-vlan epg node 1100

show role 1101

show running-config 1102

show sessions 1103

show sessions controller 1104

show sessions controller detail 1105

show sessions leaf 1106

show sessions spine 1107

show snapshot active 1108

show snapshot files 1109

show snapshot jobs 1110

show snmp 1111

show snmp clientgroups 1112

show snmp community 1113

show snmp engineid 1114

show snmp hosts 1115

show snmp users 1116

show stats 1117

show stats granularity leaf 1118

show stats granularity leaf fex 1119

show stats granularity leaf fex module 1120

show stats granularity leaf interface ethernet 1121

show stats granularity leaf interface mgmt 1122

show stats granularity leaf interface portchannel 1123

show stats granularity leaf inventory fans 1124

show stats granularity leaf inventory powersupply 1125

Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) xxxi

Contents

show stats granularity leaf inventory supervisor 1126

show stats granularity spine 1127

show stats granularity spine interface ethernet 1128

show stats granularity spine interface mgmt 1129

show stats granularity spine inventory chassis 1130

show stats granularity spine inventory fabric 1131

show stats granularity spine inventory fans 1132

show stats granularity spine inventory module 1133

show stats granularity spine inventory powersupply 1134

show stats granularity spine inventory supervisor 1135

show stats granularity spine inventory system 1136

show stats granularity tenant 1137

show stats granularity tenant application 1138

show stats granularity tenant application epg 1139

show switch 1140

show switch detail 1141

show tacacs-server 1142

show techsupport all 1143

show techsupport controllers 1144

show techsupport host 1145

show techsupport switch 1146

show tenant 1147

show tenant access-list 1148

show tenant application 1149

show tenant application endpoints 1150

show tenant application endpoints leaf interface ethernet 1151

show tenant application endpoints leaf interface port-channel 1152

show tenant application endpoints vpc 1153

show tenant application epg 1154

show tenant application epg detail 1155

show tenant application epg endpoints 1156

show tenant application epg endpoints leaf interface ethernet 1157

show tenant application epg endpoints leaf interface port-channel 1158

show tenant application epg endpoints vpc 1159

show tenant bridge-domain 1161

Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)xxxii

Contents

show tenant bridge-domain detail 1162

show tenant contract-type 1163

show tenant contract 1164

show tenant detail 1165

show tenant endpoints 1166

show tenant endpoints leaf interface ethernet 1167

show tenant endpoints leaf interface port-channel 1168

show tenant endpoints vpc 1169

show tenant epg 1170

show tenant epg detail 1171

show tenant external-l2 epg 1172

show tenant interface bridge-domain 1173

show tenant interface bridge-domain detail 1174

show tenant ip interface bridge-domain 1175

show tenant ipv6 interface bridge-domain 1176

show tenant policy-map 1177

show tenant policy-map type data-plane 1178

show tenant policy-map type qos 1179

show tenant vrf 1180

show tenant vrf detail 1181

show tenant vrf external-l3 bgp 1182

show tenant vrf external-l3 bgp node 1183

show tenant vrf external-l3 eigrp 1184

show tenant vrf external-l3 eigrp detail 1185

show tenant vrf external-l3 epg 1186

show tenant vrf external-l3 epg detail 1187

show tenant vrf external-l3 epg name 1188

show tenant vrf external-l3 epg name detail 1189

show tenant vrf external-l3 interfaces 1190

show tenant vrf external-l3 interfaces detail 1191

show tenant vrf external-l3 ospf 1192

show tenant vrf external-l3 ospf detail 1193

show tenant vrf external-l3 route-map 1194

show tenant vrf external-l3 route-map detail 1195

show tenant vrf external-l3 static-route 1196

Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) xxxiii

Contents

show tenant vrf external-l3 static-route detail 1197

show tenant vrf external-l3 static-route node 1198

show tenant vrf external-l3 static-route node detail 1199

show troubleshoot epext session 1200

show troubleshoot epext session atomiccounter 1201

show troubleshoot epext session audit 1202

show troubleshoot epext session contracts 1203

show troubleshoot epext session deployments 1204

show troubleshoot epext session events 1205

show troubleshoot epext session faults 1206

show troubleshoot epext session monitor 1207

show troubleshoot epext session reports 1208

show troubleshoot epext session statistics 1209

show troubleshoot epext session topology 1210

show troubleshoot epext session traceroute 1211

show troubleshoot epext sessions 1212

show troubleshoot eptoep session 1213

show troubleshoot eptoep session atomiccounter 1214

show troubleshoot eptoep session audit 1215

show troubleshoot eptoep session contracts 1216

show troubleshoot eptoep session deployments 1217

show troubleshoot eptoep session events 1218

show troubleshoot eptoep session faults 1219

show troubleshoot eptoep session monitor 1220

show troubleshoot eptoep session reports 1221

show troubleshoot eptoep session statistics 1222

show troubleshoot eptoep session topology 1223

show troubleshoot eptoep session traceroute 1224

show troubleshoot eptoep sessions 1225

show username 1226

show username detail 1227

show version 1228

show vlan-domain 1229

show vmware domain 1230

show vmware domain name 1231

Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)xxxiv

Contents

show vmware domain name epg 1232

show vmware domain name esx 1233

show vmware domain name port-group 1234

show vmware domain name vcenter 1235

show vmware domain name vm 1236

show vmware domain name vm name 1237

show vmware vm 1238

show vpc 1239

show vpc map leaf 1240

show vrf 1241

show vrf detail 1242

shut 1243

shutdown 1244

site-id 1246

slow-timer 1247

snapshot download 1248

snapshot export 1249

snapshot import 1250

snapshot rollback 1251

snapshot upload 1252

snmp-server clientgroup 1253

snmp-server community 1254

snmp-server contact 1255

snmp-server host 1256

snmp-server location 1257

snmp-server protocol 1258

snmp-server user 1259

source 1260

source application 1261

source interface ethernet 1262

source interface port-channel 1263

source interface vpc 1264

spanning-tree 1265

spanning-tree bpdu-filter 1268

spanning-tree bpdu-guard 1269

Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) xxxv

Contents

speed 1270

spf-interval 1272

ssh-key 1273

ssh-service 1274

ssl-protocols 1275

ssl-validation-level 1276

state 1277

static-endpoint 1278

static-tep 1281

statistics 1283

storm-control level 1284

storm-control pps 1286

street-address 1289

subject 1290

summary-address 1291

switch-group 1292

switch 1293

switching 1294

switchport 1295

switchport access vlan tenant application 1297

switchport access vlan tenant external-svi 1299

switchport trunk allowed vlan inband-mgmt 1301

switchport trunk allowed vlan tenant application 1302

switchport trunk allowed vlan tenant external-l2 1304

switchport trunk allowed vlan tenant external-svi 1306

switchport trunk allowed vlan tenant legacy-forwarding 1308

switchport trunk native vlan tenant application 1310

switchport trunk native vlan tenant external-svi 1312

switchport vlan 1314

syslog 1316

system cluster-size 1317

system controller-id 1318

system dynamic-load-balance 1319

system fabric-security-mode 1320

system jumbomtu 1321

Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)xxxvi

Contents

system switch-id 1322

C H A P T E R 1 9 T Commands 1323

tacacs-server host 1327

tacacs-server retries 1328

tacacs-server timeout 1329

tag 1330

target 1332

telnet 1333

template bfd 1334

template bgp address-family 1335

template bgp timers 1336

template community-list expanded 1337

template community-list standard 1338

template dhcp option 1339

template dhcp relay 1340

template eigrp interface-policy 1341

template eigrp vrf-policy 1342

template endpoint retention policy 1343

template extcommunity-list expanded 1344

template extcommunity-list standard 1345

template ip igmp snooping policy 1346

template ipv6 nd policy 1347

template ipv6 nd prefix 1348

template leaf-policy-group 1349

template ospf interface-policy 1350

template ospf vrf-policy 1351

template policy-group 1352

template port-channel 1353

template route-profile 1354

template route tag 1355

tenant 1356

terminal 1357

time 1358

time start daily 1359

Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) xxxvii

Contents

time start weekly 1360

timeout 1361

timers 1362

timers lsa-arrival 1364

timers lsa-group-pacing 1365

timers throttle lsa 1366

timers throttle spf 1367

tp 1368

transmit-delay 1369

transport email from 1370

transport email mail-server 1371

transport email reply-to 1372

trigger fabric-recovery 1373

trigger shutdown 1374

trigger snapshot download 1375

trigger snapshot export 1376

trigger snapshot import 1377

trigger snapshot rollback 1378

trigger snapshot upload 1379

trigger techsupport all 1380

trigger techsupport controllers 1381

trigger techsupport host 1382

trigger techsupport local 1383

trigger techsupport switch 1384

trigger troubleshoot epext session report 1385

trigger troubleshoot eptoep session report 1386

trigger vmware 1387

troubleshoot epext session atomiccounter 1388

troubleshoot epext session description 1389

troubleshoot epext session latestminutes 1390

troubleshoot epext session monitor destination apic 1391

troubleshoot epext session monitor destination prefdestgroup 1392

troubleshoot epext session monitor destination tenant 1393

troubleshoot epext session scheduler 1395

troubleshoot epext session srcextip destip tenant application 1396

Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)xxxviii

Contents

troubleshoot epext session srcextip destip tenant vrf 1397

troubleshoot epext session srcip tenant application epg destextip 1398

troubleshoot epext session srcip tenant vrf destextip 1399

troubleshoot epext session starttime 1400

troubleshoot epext session traceroute 1401

troubleshoot epext session traceroute protocol icmp 1402

troubleshoot epext session traceroute protocol tcp 1403

troubleshoot epext session traceroute protocol udp 1404

troubleshoot eptoep session atomiccounter 1405

troubleshoot eptoep session description 1406

troubleshoot eptoep session latestminutes 1407

troubleshoot eptoep session monitor destination apic 1408

troubleshoot eptoep session monitor destination prefdestgroup 1409

troubleshoot eptoep session monitor destination tenant 1410

troubleshoot eptoep session scheduler 1412

troubleshoot eptoep session srcip tenant application epg destip tenant application 1413

troubleshoot eptoep session srcip tenant application epg destip tenant vrf 1414

troubleshoot eptoep session srcip tenant vrf destip tenant application 1415

troubleshoot eptoep session srcip tenant vrf destip tenant vrf 1416

troubleshoot eptoep session srcmac tenant application epg destmac tenant application 1417

troubleshoot eptoep session srcmac tenant application epg destmac tenant vrf 1419

troubleshoot eptoep session srcmac tenant vrf destmac tenant application 1420

troubleshoot eptoep session srcmac tenant vrf destmac tenant vrf 1421

troubleshoot eptoep session starttime 1422

troubleshoot eptoep session traceroute 1423

troubleshoot eptoep session traceroute protocol icmp 1424

troubleshoot eptoep session traceroute protocol tcp 1425

troubleshoot eptoep session traceroute protocol udp 1426

trusted-key 1427

C H A P T E R 2 0 U Commands 1429

ui-idle-timeout-seconds 1430

unicast 1431

update-source ethernet 1432

update-source loopback 1433

Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) xxxix

Contents

update-source vlan 1434

use-keyring 1435

use-vrf 1436

user 1437

username 1438

C H A P T E R 2 1 V Commands 1441

vcenter 1442

vlan-domain 1443

vlan-pool 1447

vlan 1448

vmware-domain 1450

vnic 1451

vpc context 1452

vpc domain consecutive 1453

vpc domain explicit 1454

vpc domain reciprocal 1455

vrf 1456

vshield 1461

vxlan 1462

vxlan multicast-pool 1463

vxlan pool 1464

C H A P T E R 2 2 WCommands 1465

webtoken-timeout-seconds 1466

weight 1467

where 1468

where detail 1469

winservers 1470

C H A P T E R 2 3 Z Commands 1471

zone 1472

zones 1473

Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)xl

Contents

Preface

• Audience, page xli

• Document Conventions, page xli

• Related Documentation, page xliii

• Documentation Feedback, page xliii

AudienceThis guide is intended for network and systems administrators who configure and maintain the ApplicationCentric Infrastructure fabric.

Document ConventionsCommand descriptions use the following conventions:

DescriptionConvention

Bold text indicates the commands and keywords that you enter literallyas shown.

bold

Italic text indicates arguments for which the user supplies the values.Italic

Square brackets enclose an optional element (keyword or argument).[x]

Square brackets enclosing keywords or arguments separated by a verticalbar indicate an optional choice.

[x | y]

Braces enclosing keywords or arguments separated by a vertical barindicate a required choice.

{x | y}

Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) xli


Nested set of square brackets or braces indicate optional or requiredchoices within optional or required elements. Braces and a vertical barwithin square brackets indicate a required choice within an optionalelement.

[x {y | z}]

Indicates a variable for which you supply values, in context where italicscannot be used.

variable

A nonquoted set of characters. Do not use quotation marks around thestring or the string will include the quotation marks.

string

Examples use the following conventions:


Terminal sessions and information the switch displays are in screen font.screen font

Information you must enter is in boldface screen font.boldface screen font

Arguments for which you supply values are in italic screen font.italic screen font

Nonprinting characters, such as passwords, are in angle brackets.< >

Default responses to system prompts are in square brackets.[ ]

An exclamation point (!) or a pound sign (#) at the beginning of a lineof code indicates a comment line.

!, #

This document uses the following conventions:

Means reader take note. Notes contain helpful suggestions or references to material not covered in themanual.

Note

Means reader be careful. In this situation, you might do something that could result in equipment damageor loss of data.

Caution

Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)xlii

PrefaceDocument Conventions

IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before youwork on any equipment, be aware of the hazards involved with electrical circuitry and be familiar withstandard practices for preventing accidents. Use the statement number provided at the end of each warningto locate its translation in the translated safety warnings that accompanied this device.

SAVE THESE INSTRUCTIONS

Warning

Related DocumentationCisco Application Centric Infrastructure (ACI) Documentation

The ACI documentation is available at the following URL: http://www.cisco.com/c/en/us/support/cloud-systems-management/application-policy-infrastructure-controller-apic/tsd-products-support-series-home.html.

Cisco Application Centric Infrastructure (ACI) Simulator Documentation

The Cisco ACI Simulator documentation is available at http://www.cisco.com/c/en/us/support/cloud-systems-management/application-centric-infrastructure-simulator/tsd-products-support-series-home.html.

Cisco Nexus 9000 Series Switches Documentation

The Cisco Nexus 9000 Series Switches documentation is available at http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/tsd-products-support-series-home.html.

Cisco Application Virtual Switch Documentation

The Cisco Application Virtual Switch (AVS) documentation is available at http://www.cisco.com/c/en/us/support/switches/application-virtual-switch/tsd-products-support-series-home.html.

Cisco Application Centric Infrastructure (ACI) Integration with OpenStack Documentation

Cisco ACI integration with OpenStack documentation is available at http://www.cisco.com/c/en/us/support/cloud-systems-management/application-policy-infrastructure-controller-apic/tsd-products-support-series-home.html.

Documentation FeedbackTo provide technical feedback on this document, or to report an error or omission, please send your commentsto [email protected]. We appreciate your feedback.

Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) xliii

PrefaceRelated Documentation

http://www.cisco.com/c/en/us/support/cloud-systems-management/application-policy-infrastructure-controller-apic/tsd-products-support-series-home.html



http://www.cisco.com/c/en/us/support/cloud-systems-management/application-centric-infrastructure-simulator/tsd-products-support-series-home.html

http://www.cisco.com/c/en/us/support/cloud-systems-management/application-centric-infrastructure-simulator/tsd-products-support-series-home.html

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/tsd-products-support-series-home.html

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/tsd-products-support-series-home.html

http://www.cisco.com/c/en/us/support/switches/application-virtual-switch/tsd-products-support-series-home.html

http://www.cisco.com/c/en/us/support/switches/application-virtual-switch/tsd-products-support-series-home.html





Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)xliv

PrefaceDocumentation Feedback

A Commands

• aaa authentication login console, page 3

• aaa authentication login default, page 4

• aaa authentication login domain, page 5

• aaa banner, page 6

• aaa group server ldap, page 7

• aaa group server radius, page 8

• aaa group server tacacsplus, page 9

• aaa scvmm-certificate, page 10

• aaa user default-role, page 11

• absolute, page 12

• access-group, page 13

• access-list, page 14

• account-status, page 15

• action, page 16

• address-family, page 17

• address, page 19

• admin-state-enable, page 20

• admin, page 22

• advertise-subnet, page 23

• aggregate-address, page 24

• allow-origin, page 25

• allow-self-as, page 26

• allow-writes, page 27

• allowed-self-as-count, page 28

Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1

• application, page 29

• area default-cost, page 30

• area l3out, page 31

• area loopback, page 32

• area nssa, page 33

• area nssa default-information-originate, page 34

• area nssa no-redistribute, page 35

• area nssa translate, page 36

• area range, page 37

• area route-map, page 38

• area stub, page 39

• arp flooding, page 40

• asn, page 41

• attribute, page 42

• attribute match custom, page 43

• attribute match datacenter, page 44

• attribute match domain, page 45

• attribute match guest-os, page 46

• attribute match hypervisor-id, page 47

• attribute match ip, page 48

• attribute match mac, page 49

• attribute match vm-id, page 50

• attribute match vm-name, page 51

• attribute match vnic, page 52

• authenticate, page 53

• authentication-key, page 54

• auto-cost, page 55

• autonomous-system, page 56

Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)2

A Commands

aaa authentication login consoleaaa authentication login console

Description: Configure console methods

Command Mode: configure : Configuration Mode

Command Path:

# configure [['terminal', 't']](config)# aaa authentication login console


A Commandsaaa authentication login console

aaa authentication login defaultaaa authentication login default

Description: Configure default methods


Command Path:

# configure [['terminal', 't']](config)# aaa authentication login default


A Commandsaaa authentication login default

aaa authentication login domainaaa authentication login domain <WORD>

Description: Configure domain methods

Syntax:

Login domain nameWORD


Command Path:

# configure [['terminal', 't']](config)# aaa authentication login domain <WORD>


A Commandsaaa authentication login domain

aaa banneraaa banner <LINE>

Description: CLI informational banner to be displayed before user login (wrap with single quotes)

Syntax:

CLI informational banner to be displayed before user login (wrap withsingle quotes) (Max Size None)

LINE


Command Path:

# configure [['terminal', 't']](config)# aaa banner <LINE>


A Commandsaaa banner

aaa group server ldapaaa group server ldap <WORD>

Description: LDAP server group name.

Syntax:

LDAP server group nameWORD


Command Path:

# configure [['terminal', 't']](config)# aaa group server ldap <WORD>


A Commandsaaa group server ldap

aaa group server radiusaaa group server radius <WORD>

Description: RADIUS server group name.

Syntax:

RADIUS server group nameWORD


Command Path:

# configure [['terminal', 't']](config)# aaa group server radius <WORD>


A Commandsaaa group server radius

aaa group server tacacsplusaaa group server tacacsplus <WORD>

Description: TACACS+ server group name.

Syntax:

TACACS+ server group nameWORD


Command Path:

# configure [['terminal', 't']](config)# aaa group server tacacsplus <WORD>


A Commandsaaa group server tacacsplus

aaa scvmm-certificateaaa scvmm-certificate <WORD>

Description: AAACertRule

Syntax:

Certificate nameWORD


Command Path:

# configure [['terminal', 't']](config)# aaa scvmm-certificate <WORD>


A Commandsaaa scvmm-certificate

aaa user default-roleaaa user default-role <default-role-policy>

Description: Default role assigned by aaa-admin for remote authentication

Syntax:

<default-role-policy><default-role-policy>


Command Path:

# configure [['terminal', 't']](config)# aaa user default-role <default-role-policy>


A Commandsaaa user default-role

absoluteabsolute window <WORD>

Description: Absolute window configuration mode

Syntax:

Configure scheduler windowwindow

Window name (Max size 31)WORD

Command Mode: scheduler : Scheduler configuration mode

Command Path:

# configure [['terminal', 't']](config)# scheduler fabric|controller schedule <WORD>(config-scheduler)# absolute window <WORD>


A Commandsabsolute

access-groupaccess-group <WORD> <WORD>

Description: Apply an access-list on this subject

Syntax:

Name of the access-list to apply (Max Size 64)WORD

DirectionsWORD

Command Mode: subject : Configuration a subject on the contract

Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# contract <WORD> [type <type>](config-tenant-contract)# subject <WORD>(config-tenant-contract-subj)# access-group <WORD> <WORD>


A Commandsaccess-group

access-listaccess-list <WORD>

Description: Create access-list

Syntax:

Access-list Name (Max Size 64)WORD

Command Mode: tenant : tenant configuration mode

Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# access-list <WORD>


A Commandsaccess-list

account-statusaccount-status <WORD>

Description: Set The status of the locally-authenticated user account.

Syntax:

status of the locally-authenticated user accountWORD

Command Mode: username : Create a locally-authenticated user account

Command Path:

# configure [['terminal', 't']](config)# username <WORD>(config-username)# account-status <WORD>


A Commandsaccount-status

actionaction merge|replace

Description: Snapshot import action merge|replace

Syntax:

Merge with existing configurationmerge

Replace existing configurationreplace

Command Mode: snapshot import : Configuration import setup mode

Command Path:

# configure [['terminal', 't']](config)# snapshot import <WORD>(config-import)# action merge|replace


A Commandsaction

address-familyaddress-family ipv4|ipv6 unicast

Description: EIGRP Policy Address Family

Syntax:

Address Family IPv4ipv4


Unicastunicast

Command Mode: vrf : Configure VRF information

Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router eigrp default(config-eigrp)# vrf member tenant <WORD> vrf <WORD>(config-eigrp-vrf)# address-family ipv4|ipv6 unicast

address-family ipv4|ipv6 unicast

Description: Configure an address-family for peer

Syntax:

Configure IPv4 address-familyipv4


Configure Unicast sub-address-familyunicast

Command Mode: neighbor : Configure a BGP neighbor

Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [l3out <WORD>](config-leaf-bgp-vrf-neighbor)# address-family ipv4|ipv6 unicast

address-family ipv4|ipv6 unicast

Description: Configure an address-family

Syntax:


A Commandsaddress-family



Configure unicast address-familyunicast

Command Mode: vrf : Virtual Router Context

Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# address-family ipv4|ipv6 unicast


A Commandsaddress-family

addressaddress <A.B.C.D> [preferred]

Description: Configure the ip address for dns servers

Syntax:

IP address in format i.i.i.iA.B.C.D

(Optional) Configure the address to be preferredpreferred

Command Mode: dns : Configure default dns policy

Command Path:

# configure [['terminal', 't']](config)# dns(config-dns)# address <A.B.C.D> [preferred]


A Commandsaddress

admin-state-enableadmin-state-enable

Description: Enable the state of the SSH communication service

Command Mode: ssh-service : SSH communication policy group

Command Path:

# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# ssh-service(config-ssh-service)# admin-state-enable

admin-state-enable

Description: Enable the state of the TELNET communication service

Command Mode: telnet : TELNET communication policy group

Command Path:

# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# telnet(config-telnet)# admin-state-enable

admin-state-enable

Description: Enable the state of the shellinabox communication service

Command Mode: shellinabox : SHELLINABOX communication policy group

Command Path:

# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# shellinabox(config-shellinabox)# admin-state-enable

admin-state-enable

Description: Enable the state of the HTTP communication service

Command Mode: http : HTTP communication policy group

Command Path:

# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# http(config-http)# admin-state-enable

admin-state-enable

Description: Enable the state of the HTTPS communication service


A Commandsadmin-state-enable

Command Mode: https : HTTPS communication policy group

Command Path:

# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# https(config-https)# admin-state-enable


A Commandsadmin-state-enable

adminadmin enable

Description: Set admin state of syslog group

Syntax:

Enableenable

Command Mode: logging : Logging server group configuration mode

Command Path:

# configure [['terminal', 't']](config)# logging server-group <WORD>(config-logging)# admin enable


A Commandsadmin

advertise-subnetadvertise-subnet

Description: Set OSPF Interface Policy Controls

Command Mode: template ospf interface-policy : Configure OSPF Interface Policy Templates

Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf interface-policy <WORD> tenant <WORD>(config-interface-policy)# advertise-subnet


A Commandsadvertise-subnet

aggregate-addressaggregate-address <IP-PREFIX/LEN> [as-set]

Description: Route summarization

Syntax:

Aggregate IPv4 address and mask lengthIP-PREFIX/LEN

(Optional) Autonomous system set path information and communityinformation

as-set


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# aggregate-address <IP-PREFIX/LEN> [as-set]


A Commandsaggregate-address

allow-originallow-origin <WORD>

Description: The URL to return in the Access-Control-Allow-Origin HTTP header

Syntax:

The URL to return in the Access-Control-Allow-Origin HTTP header(Max Size 256)

WORD


Command Path:

# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# http(config-http)# allow-origin <WORD>


A Commandsallow-origin

allow-self-asallow-self-as

Description: Accept as-path with my AS present in it


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [l3out <WORD>](config-leaf-bgp-vrf-neighbor)# allow-self-as


A Commandsallow-self-as

allow-writesallow-writes

Description: Allow writes for the RBAC rule

Command Mode: rbac rule : Create RBAC rule, security domain users can read subtree starting at specificobject

Command Path:

# configure [['terminal', 't']](config)# rbac rule <DN> <WORD>(config-rule)# allow-writes


A Commandsallow-writes

allowed-self-as-countallowed-self-as-count <NUMBER>

Description: The number of occurrences of a local access service network

Syntax:

Number of occurrences of AS number, default is 3. Number rangefrom=1 to=10

<1-10>


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [l3out <WORD>](config-leaf-bgp-vrf-neighbor)# allowed-self-as-count <NUMBER>


A Commandsallowed-self-as-count

applicationapplication <WORD>

Description: application configuration mode

Syntax:

Application name (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>


A Commandsapplication

area default-costarea <A.B.C.D|NUMBER> default-cost <0-16777215>

Description: Set OSPF default area cost

Syntax:

OSPF area ID<A.B.C.D|NUMBER>

Cost value<0-16777215>

Command Mode: vrf : Associate Router OSPF Policy with Tenant/VRF

Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# area <A.B.C.D|NUMBER> default-cost <0-16777215>


A Commandsarea default-cost

area l3outarea <A.B.C.D|NUMBER> l3out <l3out name>

Description: Enable OSPF in the l3Out

Syntax:


Configure ASN on an API configured L3Out<l3out name>


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# area <A.B.C.D|NUMBER> l3out <l3out name>


A Commandsarea l3out

area loopbackarea <A.B.C.D|NUMBER> loopback <Loopback Ip Address>

Description: Configure OSPF on Loopback

Syntax:


Loopback Ip<Loopback Ip Address>


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# area <A.B.C.D|NUMBER> loopback <Loopback Ip Address>


A Commandsarea loopback

area nssaarea <A.B.C.D|NUMBER> nssa

Description: Configure area as nssa

Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# area <A.B.C.D|NUMBER> nssa


A Commandsarea nssa

area nssa default-information-originatearea <A.B.C.D|NUMBER> nssa default-information-originate [no-redistribute]

Description: Originate a default route

Syntax:


(Optional) No Redistribute area optionno-redistribute


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# area <A.B.C.D|NUMBER> nssa default-information-originate[no-redistribute]


A Commandsarea nssa default-information-originate

area nssa no-redistributearea <A.B.C.D|NUMBER> nssa no-redistribute [default-information-originate]

Description: Configure area as no-redistribute

Syntax:


(Optional) Originate a default routedefault-information-originate


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# area <A.B.C.D|NUMBER> nssa no-redistribute[default-information-originate]


A Commandsarea nssa no-redistribute

area nssa translatearea <A.B.C.D|NUMBER> nssa translate type7 suppress-fa

Description: Translate LSAs

Syntax:


From Type 7 to Type 5type7

Suppress forwarding address in translated LSAssuppress-fa


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# area <A.B.C.D|NUMBER> nssa translate type7 suppress-fa


A Commandsarea nssa translate

area rangearea <A.B.C.D|NUMBER> range <IP-PREFIX/LENGTH> [cost <cost>]

Description: range

Syntax:


Summarized IPIP-PREFIX/LENGTH

(Optional) Route costcost


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# area <A.B.C.D|NUMBER> range <IP-PREFIX/LENGTH> [cost <cost>]


A Commandsarea range

area route-maparea <A.B.C.D|NUMBER> route-map <WORD> out

Description: Set Route Map

Syntax:


Route Map Name (Max Size 63)WORD

Apply policy to outgoing routesout


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# area <A.B.C.D|NUMBER> route-map <WORD> out


A Commandsarea route-map

area stubarea <A.B.C.D|NUMBER> stub

Description: Configure area as a stub

Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# area <A.B.C.D|NUMBER> stub


A Commandsarea stub

arp floodingarp flooding

Description: Enable ARP flooding

Command Mode: bridge-domain : Configuration for bridge-domain

Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>(config-tenant-bd)# arp flooding


A Commandsarp flooding

asnasn <NUMBER>

Description: Configure BGP Autonomous System number

Syntax:

Number that uniquely identifies an autonomous system. Number rangefrom=1 to=4294967295

<1-4294967295>

Command Mode: bgp : Border Gateway Protocol (BGP)

Command Path:

# configure [['terminal', 't']](config)# pod 1(config-pod)# bgp fabric(config-pod-bgp)# asn <NUMBER>


A Commandsasn

attributeattribute <WORD>

Description: An LDAP endpoint attribute to be used as the CiscoAVPair

Syntax:

LDAP endpoint attribute (Max Size 63)<WORD>

Command Mode: ldap-server host : LDAP server DNS name or IP address

Command Path:

# configure [['terminal', 't']](config)# ldap-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# attribute <WORD>


A Commandsattribute

attribute match customattribute <WORD> match custom <WORD> <arg> <WORD>

Description: Configure a Custom attribute

Syntax:

uSeg attribute nameWORD

Match criteriamatch

custom label nameWORD

arg

string to be matchedWORD

Command Mode: epg : AEPg configuration mode

Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# attribute <WORD> match custom <WORD> <> <WORD>


A Commandsattribute match custom

attribute match datacenterattribute <WORD> match datacenter <arg> <WORD>

Description: Configure a Datacenter name attribute

Syntax:


Match criteriamatch

arg

ValueWORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# attribute <WORD> match datacenter <> <WORD>


A Commandsattribute match datacenter

attribute match domainattribute <WORD> match domain <arg> <WORD>

Description: Configure a Domain name attribute

Syntax:


Match criteriamatch

arg

ValueWORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# attribute <WORD> match domain <> <WORD>


A Commandsattribute match domain

attribute match guest-osattribute <WORD> match guest-os <arg> <WORD>

Description: Configure a Guest-OS attribute

Syntax:


Match criteriamatch

arg

ValueWORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# attribute <WORD> match guest-os <> <WORD>


A Commandsattribute match guest-os

attribute match hypervisor-idattribute <WORD> match hypervisor-id <arg> <WORD>

Description: Configure a Hypervisor ID attribute

Syntax:


Match criteriamatch

arg

ValueWORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# attribute <WORD> match hypervisor-id <> <WORD>


A Commandsattribute match hypervisor-id

attribute match ipattribute <WORD> match ip <ip-addr/mask>

Description: Configure a IP address attribute

Syntax:


Match criteriamatch

Full IP Address and mask<ip-addr/mask>


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# attribute <WORD> match ip <ip-addr/mask>


A Commandsattribute match ip

attribute match macattribute <WORD> match mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE

Description: Configure a MAC address attribute

Syntax:


Match criteriamatch

MAC address (Option 1)E.E.E

MAC address (Option 2)EE-EE-EE-EE-EE-EE

MAC address (Option 3)EE:EE:EE:EE:EE:EE

MAC address (Option 4)EEEE.EEEE.EEEE


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# attribute <WORD> match macE.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE


A Commandsattribute match mac

attribute match vm-idattribute <WORD> match vm-id <arg> <WORD>

Description: Configure a VM identifier attribute

Syntax:


Match criteriamatch

arg

ValueWORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# attribute <WORD> match vm-id <> <WORD>


A Commandsattribute match vm-id

attribute match vm-nameattribute <WORD> match vm-name <arg> <WORD>

Description: Configure a VM name attribute

Syntax:


Match criteriamatch

arg

ValueWORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# attribute <WORD> match vm-name <> <WORD>


A Commandsattribute match vm-name

attribute match vnicattribute <WORD> match vnic <arg> <WORD>

Description: Configure a Vnic name attribute

Syntax:


Match criteriamatch

arg

ValueWORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# attribute <WORD> match vnic <> <WORD>


A Commandsattribute match vnic

authenticateauthenticate

Description: Configure authentication for the default ntp policy

Command Mode: ntp : Configure the default ntp policy

Command Path:

# configure [['terminal', 't']](config)# pod 1(config-pod)# ntp(config-ntp)# authenticate


A Commandsauthenticate

authentication-keyauthentication-key <id> [md5 <md5>]

Description: Configure ntp authentication keys for the default ntp policy

Syntax:

Id for the authentication key. Number range from=1 to=65535id

(Optional) Configure the authentication key (Max Size 510)md5


Command Path:

# configure [['terminal', 't']](config)# pod 1(config-pod)# ntp(config-ntp)# authentication-key <id> [md5 <md5>]


A Commandsauthentication-key

auto-costauto-cost reference-bandwidth <NUMBER>

Description: Set OSPF Policy Bandwidth Reference

Syntax:

OSPF Policy Bandwidth Referencereference-bandwidth

BandwidthReferenceValue inMbps. Number range from=1 to=4000000<1-4000000>

Command Mode: template ospf vrf-policy : Configure Router OSPF Timer Policy Templates

Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf vrf-policy <WORD> tenant <WORD>(config-vrf-policy)# auto-cost reference-bandwidth <NUMBER>


A Commandsauto-cost

autonomous-systemautonomous-system <NUMBER> [l3out <l3out>]

Description: Autonomous System Configuration for EIGRP

Syntax:

The autonomous system number. Number range from=1 to=65535<1-65535>

(Optional) Configure ASN on an API configured L3Outl3out


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router eigrp default(config-eigrp)# vrf member tenant <WORD> vrf <WORD>(config-eigrp-vrf)# autonomous-system <NUMBER> [l3out <l3out>]


A Commandsautonomous-system

B Commands

• bandwidth, page 58

• basedn, page 59

• bash, page 60

• bfd, page 61

• bfd ip ipv6 authentication, page 62

• bfd ip ipv6 inherit, page 64

• bfd ip ipv6 tenant, page 65

• bgp, page 66

• binddn, page 67

• bpdu-filter, page 68

• bridge-domain, page 69


bandwidthbandwidth <NUMBER>

Description: Set the desired bandwidth to police to

Syntax:

Bandwidth percentage guaranteed as %. Number range from=0 to=100<0-100>

Command Mode: qos parameters : Configure the global QOS policies

Command Path:

# configure [['terminal', 't']](config)# qos parameters level1|level2|level3(config-qos)# bandwidth <NUMBER>


B Commandsbandwidth

basednbasedn <WORD>

Description: The LDAP base DN for user lookup in the LDAP directory tree

Syntax:

user lookup in LDAP directory tree (Max Size 127)<WORD>


Command Path:

# configure [['terminal', 't']](config)# ldap-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# basedn <WORD>


B Commandsbasedn

bashbash

Description: bash shell for unix commands

Command Mode: exec : Exec Mode

Command Path:

# bash


B Commandsbash

bfdbfd enable

Description: Enable Bidirectional Forwarding Detection

Syntax:

Enable BFDenable


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf interface-policy <WORD> tenant <WORD>(config-interface-policy)# bfd enable

bfd enable


Syntax:

Enable BFDenable


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [l3out <WORD>](config-leaf-bgp-vrf-neighbor)# bfd enable


B Commandsbfd

bfd ip ipv6 authenticationbfd ip|ipv6 authentication keyed-sha1 keyid <NUMBER> key <WORD>

Description: Configure BFD authentication

Syntax:

IPv4ip

IPv6ipv6

Configure Keyed SHA1 authenticationkeyed-sha1

Configure authentication key IDkeyid

Authentication key ID. Number range from=1 to=255<keyid>

Configure shared authentication keykey

Shared authentication key (Max Size 20)WORD

Command Mode: interface vlan : Vlan interface

Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# bfd ip|ipv6 authentication keyed-sha1 keyid <NUMBER> key <WORD>

bfd ip|ipv6 authentication keyed-sha1 keyid <NUMBER> key <WORD>

Description: Configure BFD authentication

Syntax:

IPv4ip

IPv6ipv6

Configure Keyed SHA1 authenticationkeyed-sha1

Configure authentication key IDkeyid

Authentication key ID. Number range from=1 to=255<keyid>

Configure shared authentication keykey

Shared authentication key (Max Size 20)WORD


B Commandsbfd ip ipv6 authentication

Command Mode: interface ethernet : Ethernet IEEE 802.3z

Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# bfd ip|ipv6 authentication keyed-sha1 keyid <NUMBER> key <WORD>


B Commandsbfd ip ipv6 authentication

bfd ip ipv6 inheritbfd ip|ipv6 inherit interface-policy <WORD>

Description: Inherit BFD interface template policy

Syntax:

IPv4ip

IPv6ipv6

Associate the interface with a BFD interface policyinterface-policy

Policy nameWORD


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# bfd ip|ipv6 inherit interface-policy <WORD>

bfd ip|ipv6 inherit interface-policy <WORD>

Description: Inherit BFD interface template policy

Syntax:

IPv4ip

IPv6ipv6

Associate the interface with a BFD interface policyinterface-policy

Policy nameWORD


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# bfd ip|ipv6 inherit interface-policy <WORD>


B Commandsbfd ip ipv6 inherit

bfd ip ipv6 tenantbfd ip|ipv6 tenant mode

Description: Enable BFD Tenant Mode

Syntax:

IPv4ip

IPv6ipv6

Modemode


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# bfd ip|ipv6 tenant mode

bfd ip|ipv6 tenant mode

Description: Enable BFD Tenant Mode

Syntax:

IPv4ip

IPv6ipv6

Modemode


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# bfd ip|ipv6 tenant mode


B Commandsbfd ip ipv6 tenant

bgpbgp fabric

Description: Border Gateway Protocol (BGP)

Syntax:

Fabric BGP configurationfabric

Command Mode: pod : Pod configuration mode

Command Path:

# configure [['terminal', 't']](config)# pod 1(config-pod)# bgp fabric


B Commandsbgp

binddnbinddn <WORD>

Description: The LDAP bind DN for user lookup in the LDAP directory tree

Syntax:



Command Path:

# configure [['terminal', 't']](config)# ldap-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# binddn <WORD>


B Commandsbinddn

bpdu-filterbpdu-filter

Description: Enable BPDU filter for extended chassis ports

Command Mode: spanning-tree : STP MST configuration mode

Command Path:

# configure [['terminal', 't']](config)# spanning-tree mst configuration(config-stp)# bpdu-filter


B Commandsbpdu-filter

bridge-domainbridge-domain <WORD>

Description: Configuration for bridge-domain

Syntax:

Name of the bridge-domain (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>

bridge-domain member <WORD>

Description: Bind the EPG to a bridge-domain

Syntax:

Bind the EPG to a bridge-domainmember

bridge-domain to associate (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# bridge-domain member <WORD>

bridge-domain <WORD>


Syntax:

bridge domain associated with epg suggestion use "inb"WORD

Command Mode: inband-mgmt : Enter Inside In-band management mode to modify inband properties orcreate new inband


B Commandsbridge-domain

Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# inband-mgmt epg <WORD>(config-inb-epg)# bridge-domain <WORD>

bridge-domain member <WORD>


Syntax:

Bind the EPG to a bridge-domainmember

bridge-domain to associate (Max Size 64)WORD

Command Mode: external-l2 : L2 external EPG creation/configuration

Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l2 epg <WORD>(config-tenant-l2ext-epg)# bridge-domain member <WORD>

bridge-domain tenant <tenant> name <name>

Description: Configure Bridge Domain For a L4-L7 Graph Connector.

Syntax:

Tenant in which the bridge domain is availabletenant

Tenant in which the bridge domain is available<tenant>

Bridge domain namename

Name of bd<name>

Command Mode: connector : Configure Connector for a Service Node

Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 graph <WORD> [contract <contract-option>](config-graph)# service <WORD> [device-cluster-tenant <WORD>] [device-cluster <WORD>] [mode<Available Modes>](config-service)# connector <WORD> [cluster-interface <WORD>](config-connector)# bridge-domain tenant <tenant> name <name>


B Commandsbridge-domain

C Commands

• callhome, page 73

• catalog-version, page 74

• cdp, page 75

• cert-chain, page 78

• cert, page 79

• certificate, page 80

• channel-group, page 81

• channel-mode, page 83

• ciphers, page 86

• clear-encryption-key, page 87

• clear-pwd-history, page 88

• clear endpoints, page 89

• clear snapshot file, page 90

• clear snapshot job, page 91

• clear techsupport controllers, page 92

• clear techsupport switch, page 93

• clear troubleshoot epext session report, page 94

• clear troubleshoot eptoep session report, page 95

• clock display-format, page 96

• clock show-offset, page 97

• clock timezone, page 98

• cluster-device, page 99

• cluster-device query-device-health, page 100

• cluster-device query-device-statistics, page 101


• cluster-device query-device-validation, page 102

• cluster-interface, page 103

• comm-policy, page 104

• configure-avs, page 105

• configure-dvs, page 106

• configure, page 107

• connection intra service, page 108

• connection terminal, page 109

• connector, page 110

• console, page 111

• contract-id, page 112

• contract, page 113

• contract consumer, page 114

• contract deny, page 117

• contract enforce, page 119

• contract provider, page 120

• controller-group, page 123

• controller, page 124

• cost, page 125

• country, page 126

• crypto aes, page 127

• crypto ca, page 128

• crypto keyring, page 129

• crypto webtoken, page 130

• csr, page 131

• customer-id, page 132


C Commands

callhomecallhome common

Description: Callhome common policy configuration mode

Syntax:

Callhome common policy configuration modecommon


Command Path:

# configure [['terminal', 't']](config)# callhome common


C Commandscallhome

catalog-versioncatalog-version <version>

Description: Change catalog version

Syntax:

firmware version<version>

Command Mode: firmware : Firmware upgrade configuration Mode

Command Path:

# configure [['terminal', 't']](config)# firmware(config-firmware)# catalog-version <version>


C Commandscatalog-version

cdpcdp enable|default

Description: Configure CDP parameters on DVS uplink ports

Syntax:

Enable CDPenable

Remove CDP override policydefault

Command Mode: configure-dvs : Configure a VMware Domain as DVS type

Command Path:

# configure [['terminal', 't']](config)# vmware-domain <WORD>(config-vmware)# configure-dvs(config-vmware-dvs)# cdp enable|default

cdp enable|default

Description: Configure CDP parameters on AVS uplink ports

Syntax:

Enable CDPenable

Remove CDP override policydefault

Command Mode: configure-avs : Configure a VMware Domain as AVS (N1K) type

Command Path:

# configure [['terminal', 't']](config)# vmware-domain <WORD>(config-vmware)# configure-avs(config-vmware-avs)# cdp enable|default

cdp enable

Description: Configure CDP interface parameters

Syntax:

Configure CDP parametersenable

Command Mode: template policy-group : Configure Policy Group Parameters


C Commandscdp

Command Path:

# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# cdp enable

cdp enable


Syntax:


Command Mode: template port-channel : Configure Port-Channel Parameters

Command Path:

# configure [['terminal', 't']](config)# template port-channel <WORD>(config-if)# cdp enable

cdp enable


Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# cdp enable

cdp enable


Syntax:


Command Mode: interface port-channel : Port Channel interface

Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>


C Commandscdp

(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# cdp enable

cdp enable


Syntax:


Command Mode: interface : Provide VPC Name

Command Path:

# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# cdp enable


C Commandscdp

cert-chaincert-chain <WORD>

Description: Set The PEM-encoded chain of trust from the trustpoint to a trusted root authority.

Syntax:

The PEM-encoded chain of trust from the trustpoint to a trusted rootauthority

<WORD>

Command Mode: crypto ca : Configure certificate authority related information

Command Path:

# configure [['terminal', 't']](config)# crypto ca <WORD>(config-ca)# cert-chain <WORD>


C Commandscert-chain

certcert <CERTIFICATE>

Description: Provide a certificate, that contains public key and signed information.

Syntax:

Provide a certificate in quotes, that contains public key and signedinformation

<CERTIFICATE>

Command Mode: crypto keyring : A keyring mode to create and hold an SSL certificate

Command Path:

# configure [['terminal', 't']](config)# crypto keyring <WORD>(config-keyring)# cert <CERTIFICATE>


C Commandscert

certificatecertificate <WORD>

Description: Create AAA user certificate in X.509 format.

Syntax:

Name for the user certificateWORD


Command Path:

# configure [['terminal', 't']](config)# username <WORD>(config-username)# certificate <WORD>


C Commandscertificate

channel-groupchannel-group <WORD> [vpc]

Description: Create Port Channel

Syntax:

Port-Channel/VPC Name (Max Size 64)WORD

(Optional) Configure channel-group as VPCvpc

Command Mode: leaf-interface-group : Configure Leaf Interface Group

Command Path:

# configure [['terminal', 't']](config)# leaf-interface-profile <WORD>(config-leaf-if-profile)# leaf-interface-group <WORD>(config-leaf-if-group)# channel-group <WORD> [vpc]

channel-group <WORD> [vpc]

Description: Configure Port Channel on Fex

Syntax:


(Optional) Create the channel-group as a VPCvpc

Command Mode: fex-interface-group : Configure Fex Interface Group

Command Path:

# configure [['terminal', 't']](config)# fex-profile <WORD>(config-fex-profile)# fex-interface-group <WORD>(config-fex-if-group)# channel-group <WORD> [vpc]

channel-group <WORD> [vpc]

Description: Associate a Channel Group to this Interface

Syntax:


(Optional) Create the channel-group as a VPCvpc


C Commandschannel-group


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# channel-group <WORD> [vpc]


C Commandschannel-group

channel-modechannel-mode on|active|passive|mac-pinning

Description: Configure LACP mode override on DVS uplink ports

Syntax:

Set channeling mode to ON (static)on

Set channeling mode to ACTIVEactive

Set channeling mode to PASSIVEpassive

Set channeling mode to MAC-PINNINGmac-pinning


Command Path:

# configure [['terminal', 't']](config)# vmware-domain <WORD>(config-vmware)# configure-dvs(config-vmware-dvs)# channel-mode on|active|passive|mac-pinning

channel-mode on|active|passive|mac-pinning

Description: Configure LACP mode override on AVS uplink ports

Syntax:






Command Path:

# configure [['terminal', 't']](config)# vmware-domain <WORD>(config-vmware)# configure-avs(config-vmware-avs)# channel-mode on|active|passive|mac-pinning


C Commandschannel-mode


Description: Configure channeling mode

Syntax:






Command Path:

# configure [['terminal', 't']](config)# template port-channel <WORD>(config-if)# channel-mode on|active|passive|mac-pinning



Syntax:






Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# channel-mode on|active|passive|mac-pinning



Syntax:








Command Path:

# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# channel-mode on|active|passive|mac-pinning



ciphersciphers <WORD>

Description: HTTPS cipher suite

Syntax:

Provide a valid cipher nameWORD


Command Path:

# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# https(config-https)# ciphers <WORD>


C Commandsciphers

clear-encryption-keyclear-encryption-key

Description: Clears AES encryption key

Command Mode: crypto aes : AES encryption configuration

Command Path:

# configure [['terminal', 't']](config)# crypto aes(config-aes)# clear-encryption-key


C Commandsclear-encryption-key

clear-pwd-historyclear-pwd-history

Description: Clears the password history of a locally-authenticated user


Command Path:

# configure [['terminal', 't']](config)# username <WORD>(config-username)# clear-pwd-history


C Commandsclear-pwd-history

clear endpointsclear endpoints leaf <node-id> tenant <tenant-name> bridge-domain <bd-name> vlan <NUMBER>

Description: Clear endpoints

Syntax:

Leaf Numberleaf

Leaf Number (Max Size 4000). Number range from=0to=9223372036854775807

node-id

Tenant Hosting the endpointstenant

Tenant Hosting the endpoints (Max Size 63)tenant-name

Bridge-Domain Hosting the endpointsbridge-domain

Bridge-Domain Hosting the endpoints (Max Size 64)bd-name

The encapsulation VLAN Hosting the endpointsvlan

The number of the encapsulation VLAN, from 1 to 4094. For example,for vlan-23 you enter 23 in this field.

<1-4094>


Command Path:

# clear endpoints leaf <WORD> tenant <WORD> bridge-domain <WORD> vlan <NUMBER>


C Commandsclear endpoints

clear snapshot fileclear snapshot file <WORD>

Description: Remove snapshot file

Syntax:

Snapshot file nameWORD


Command Path:

# clear snapshot file <WORD>


C Commandsclear snapshot file

clear snapshot jobclear snapshot job <WORD>

Description: Remove snapshot job

Syntax:

Snapshot job nameWORD


Command Path:

# clear snapshot job <WORD>


C Commandsclear snapshot job

clear techsupport controllersclear techsupport controllers <NUMBER> <WORD>

Description: Clear techsupport status for controllers

Syntax:

Controller id. Number range from=1 to=32<1-32>

Techsupport collection timeWORD


Command Path:

# clear techsupport controllers <NUMBER> <WORD>


C Commandsclear techsupport controllers

clear techsupport switchclear techsupport switch <NUMBER> <WORD>

Description: Clear techsupport status for switch

Syntax:

Switch id. Number range from=101 to=4000<101-4000>

Techsupport collection timeWORD


Command Path:

# clear techsupport switch <NUMBER> <WORD>


C Commandsclear techsupport switch

clear troubleshoot epext session reportclear troubleshoot epext session <ession_name> report

Description: Remove all non-pending reports of a troubleshoot session

Syntax:

sessionsession

Session nameession_name


Command Path:

# clear troubleshoot epext session <ession_name> report


C Commandsclear troubleshoot epext session report

clear troubleshoot eptoep session reportclear troubleshoot eptoep session <session_name> report

Description: Remove all non-pending reports of a troubleshoot session

Syntax:

sessionsession

Session namesession_name


Command Path:

# clear troubleshoot eptoep session <session_name> report


C Commandsclear troubleshoot eptoep session report

clock display-formatclock display-format local|utc

Description: Configure Clock Display Format

Syntax:

Local display formatlocal

UTC display formatutc


Command Path:

# configure [['terminal', 't']](config)# clock display-format local|utc


C Commandsclock display-format

clock show-offsetclock show-offset enable

Description: Enable/Disable Display of the Offset

Syntax:

Enable/Disable Display of the Offset from UTCenable


Command Path:

# configure [['terminal', 't']](config)# clock show-offset enable


C Commandsclock show-offset

clock timezoneclock timezone <timeZone>

Description: Configure clock timezone

Syntax:

The Timezone SelectiontimeZone


Command Path:

# configure [['terminal', 't']](config)# clock timezone <timeZone>


C Commandsclock timezone

cluster-devicecluster-device <WORD> [vcenter <WORD>] [vm <WORD>]

Description: Configure L4-L7 Cluster Device

Syntax:

device name (Max Size 64)WORD

(Optional) vcenter name (Max Size 64)WORD

(Optional) vm name (Max Size 128)WORD

Command Mode: l4l7 cluster name : Add a L4-L7 Service Device Cluster

Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 cluster name <WORD> type <type> vlan-domain <domain-name> [service<service>] [function <function>](config-cluster)# cluster-device <WORD> [vcenter <WORD>] [vm <WORD>]


C Commandscluster-device

cluster-device query-device-healthcluster-device <WORD> [vcenter <WORD>] [vm <WORD>] query-device-health

Description: Re-query for Device Health

Syntax:





Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 cluster name <WORD> type <type> vlan-domain <domain-name> [service<service>] [function <function>](config-cluster)# cluster-device <WORD> [vcenter <WORD>] [vm <WORD>] query-device-health


C Commandscluster-device query-device-health

cluster-device query-device-statisticscluster-device <WORD> [vcenter <WORD>] [vm <WORD>] query-device-statistics

Description: Re-query for Device Statistics

Syntax:





Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 cluster name <WORD> type <type> vlan-domain <domain-name> [service<service>] [function <function>](config-cluster)# cluster-device <WORD> [vcenter <WORD>] [vm <WORD>] query-device-statistics


C Commandscluster-device query-device-statistics

cluster-device query-device-validationcluster-device <WORD> [vcenter <WORD>] [vm <WORD>] query-device-validation

Description: Re-query for Device Validation

Syntax:





Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 cluster name <WORD> type <type> vlan-domain <domain-name> [service<service>] [function <function>](config-cluster)# cluster-device <WORD> [vcenter <WORD>] [vm <WORD>] query-device-validation


C Commandscluster-device query-device-validation

cluster-interfacecluster-interface <WORD> [vlan <NUMBER>]

Description: Configure L4-L7 Cluster Interface

Syntax:

Cluster interface name (Max Size 16)WORD

(Optional) Static Encap/VLAN to user for this cluster interface. Numberrange from=1 to=4094

<vlan>


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 cluster name <WORD> type <type> vlan-domain <domain-name> [service<service>] [function <function>](config-cluster)# cluster-interface <WORD> [vlan <NUMBER>]


C Commandscluster-interface

comm-policycomm-policy <WORD>

Description: Configure any communication policy, ssh/telnet/shellinabox/http/https

Syntax:

Provide a communication policy nameWORD


Command Path:

# configure [['terminal', 't']](config)# comm-policy <WORD>


C Commandscomm-policy

configure-avsconfigure-avs

Description: Configure a VMware Domain as AVS (N1K) type

Command Mode: vmware-domain : Create a VMM VMware Domain

Command Path:

# configure [['terminal', 't']](config)# vmware-domain <WORD>(config-vmware)# configure-avs


C Commandsconfigure-avs

configure-dvsconfigure-dvs

Description: Configure a VMware Domain as DVS type


Command Path:

# configure [['terminal', 't']](config)# vmware-domain <WORD>(config-vmware)# configure-dvs


C Commandsconfigure-dvs

configureconfigure [['terminal', 't']]

Description: Configuration Mode

Syntax:

(Optional) configure using terminalterminal

(Optional) configure using terminalterminal


Command Path:

# configure [['terminal', 't']]


C Commandsconfigure

connection intra serviceconnection <WORD> intra_service service1 <WORD> connector1 <WORD> service2 <WORD> connector2<WORD>

Description: Configure l4l7 connection between service nodes

Syntax:

Connection name (Max Size 64)WORD

Service node 1service1

service-node-1 name (Max Size 64)WORD

Connector on service node 1 that connects to the connectionconnector1

service-node-1 connector name (Max Size 64)WORD

Service node 2service2

service-node-2 name (Max Size 64)WORD

Connector on service node 2 that connects to the connectionconnector2

service-node-2 connector name (Max Size 64)WORD

Command Mode: l4l7 graph : Configure L4-L7 Service Graph

Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 graph <WORD> [contract <contract-option>](config-graph)# connection <WORD> intra_service service1 <WORD> connector1 <WORD> service2<WORD> connector2 <WORD>


C Commandsconnection intra service

connection terminalconnection <WORD> terminal provider|consumer service <WORD> connector <WORD>

Description: Configure l4l7 connection to terminal

Syntax:

Connection name (Max Size 64)WORD

Provider terminalprovider

Consumer terminalconsumer

Service node that connects to a terminal nodeservice

service node name (Max Size 64)WORD

Connector on the service node that connects to a terminal nodeconnector

connector name (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 graph <WORD> [contract <contract-option>](config-graph)# connection <WORD> terminal provider|consumer service <WORD> connector <WORD>


C Commandsconnection terminal

connectorconnector <WORD> [cluster-interface <WORD>]

Description: Configure Connector for a Service Node

Syntax:

Connector name (Max Size 64)WORD

(Optional) Cluster Interface name (Max Size 16)WORD

Command Mode: service : Configure L4-L7 Service

Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 graph <WORD> [contract <contract-option>](config-graph)# service <WORD> [device-cluster-tenant <WORD>] [device-cluster <WORD>] [mode<Available Modes>](config-service)# connector <WORD> [cluster-interface <WORD>]


C Commandsconnector

consoleconsole [severity severity <severity-value>]

Description: Enable the logging to console(switches only)

Syntax:

(Optional) The severity level for the logsseverity <severity-value>


Command Path:

# configure [['terminal', 't']](config)# logging server-group <WORD>(config-logging)# console [severity severity <severity-value>]


C Commandsconsole

contract-idcontract-id <WORD>

Description: Service contract id of the customer

Syntax:

The contract id (Max Size 512) surrounded by quotesWORD

Command Mode: destination-profile : Configure destination profile Parameters

Command Path:

# configure [['terminal', 't']](config)# callhome common(config-callhome)# destination-profile(config-callhome-destnprof)# contract-id <WORD>


C Commandscontract-id

contractcontract <WORD> [type <type>]

Description: Configure binary contracts between Application EPGs

Syntax:

Name of the contract to create (Max Size 64)WORD

(Optional) whitelist (permit) or blacklist(deny) or oob-mgmt type ofcontract

type


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# contract <WORD> [type <type>]


C Commandscontract

contract consumercontract consumer <WORD> [qos-class <WORD>]

Description: Add the supplied contract to be consumed by any AEPg on this VRF

Syntax:

Whitelist contract to consume (Max Size 64)WORD

(Optional) Qos LevelWORD

Command Mode: vrf : Configuration for vrf

Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# contract consumer <WORD> [qos-class <WORD>]

contract consumer <WORD> [imported] [label <WORD>] [qos-class <WORD>]

Description: Add a contract consumed by this AEPg, along with an optional list of subject labels

Syntax:


(Optional) used for contracts imported from other tenantsimported

(Optional) Per-Contract label (Max Size 64)WORD



Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# contract consumer <WORD> [imported] [label <WORD>] [qos-class<WORD>]

contract consumer <contractName> [imported] [label <WORD>]

Description: Add a contract consumed by this EPG, along with an optional list of subject labels

Syntax:


C Commandscontract consumer

Whitelist contract to consume<contractName>

(Optional) Used for contracts imported from other tenantsimported


Command Mode: external-l3 epg : External L3 EPG configuration mode

Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l3 epg <WORD> [oob-mgmt] [l3out <l3out>](config-tenant-l3ext-epg)# contract consumer <contractName> [imported] [label <WORD>]

contract consumer <contractName> [label <label>]

Description: Add a contract consumed by this In-band Epg, along with an optional list of subject labels

Syntax:

link to contract name<contractName>

(Optional)label


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# inband-mgmt epg <WORD>(config-inb-epg)# contract consumer <contractName> [label <label>]

contract consumer <WORD> [imported] [label <WORD>] [qos-class <WORD>]

Description: Add a contract consumed by this EPG, along with an optional list of subject labels

Syntax:


(Optional) used for contracts imported from other tenantsimported






Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l2 epg <WORD>(config-tenant-l2ext-epg)# contract consumer <WORD> [imported] [label <WORD>] [qos-class<WORD>]

contract consumer <WORD> [imported]

Description: Add a consumer contract

Syntax:

Whitelist contract to consumeWORD

(Optional) Used for contracts imported from other tenantsimported

Command Mode: match prefix-list : Match entries of a prefix-list

Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match prefix-list <WORD>(config-leaf-vrf-route-map-match)# contract consumer <WORD> [imported]



contract denycontract deny <WORD>

Description: Attach a taboo contract to this AEPg

Syntax:

Name of the blacklist contract (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# contract deny <WORD>

contract deny <contractName>

Description: Attach a taboo contract to this EPG

Syntax:

Name of the blacklist contract<contractName>


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l3 epg <WORD> [oob-mgmt] [l3out <l3out>](config-tenant-l3ext-epg)# contract deny <contractName>

contract deny <contractName>

Description: Attach a taboo contract to this InBand Epg

Syntax:

Name of the blacklist contract<contractName>


Command Path:



C Commandscontract deny

(config)# tenant <WORD>(config-tenant)# inband-mgmt epg <WORD>(config-inb-epg)# contract deny <contractName>

contract deny <WORD>

Description: Attach a taboo contract to this EPG

Syntax:

Name of the blacklist contract (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l2 epg <WORD>(config-tenant-l2ext-epg)# contract deny <WORD>


C Commandscontract deny

contract enforcecontract enforce [ingress] [egress]

Description: Add a policy enforcement

Syntax:

(Optional) Policy will be applied at the Ingress Nodeingress

(Optional) Policy will be applied at the Egress Nodeegress


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# contract enforce [ingress] [egress]


C Commandscontract enforce

contract providercontract provider <WORD> [qos-class <WORD>]

Description: Add the supplied contract to be provided by any AEPg on this VRF

Syntax:

Whitelist contract provided (Max Size 64)WORD



Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# contract provider <WORD> [qos-class <WORD>]

contract provider <WORD> [label <WORD>] [qos-class <WORD>]

Description: Contract provided by this AEPg, along with an optional list of subject labels

Syntax:

Whitelist contract to provide (Max Size 64)WORD




Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# contract provider <WORD> [label <WORD>] [qos-class <WORD>]

contract provider <contractName> [label <WORD>]

Description: Add a contract provided by this EPG, along with an optional list of subject labels

Syntax:

Whitelist contract to provide<contractName>


C Commandscontract provider



Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l3 epg <WORD> [oob-mgmt] [l3out <l3out>](config-tenant-l3ext-epg)# contract provider <contractName> [label <WORD>]

contract provider <contractName> [label <label>]

Description: Add a contract provided by this AEPg, along with an optional list of subject labels

Syntax:

link to contract name<contractName>

(Optional)label


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# inband-mgmt epg <WORD>(config-inb-epg)# contract provider <contractName> [label <label>]

contract provider <WORD> [label <WORD>] [qos-class <WORD>]

Description: Add a contract provided by this EPG, along with an optional list of subject labels

Syntax:

Whitelist contract to provide (Max Size 64)WORD




Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l2 epg <WORD>(config-tenant-l2ext-epg)# contract provider <WORD> [label <WORD>] [qos-class <WORD>]



contract provider <contractName>

Description: Add a contract provided by this AEPg, along with an optional list of subject labels

Syntax:

Name of the contract to be provided<contractName>

Command Mode: oob-mgmt : Creates/Modify the out of band mgmt under the tenant mgmt

Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# oob-mgmt epg <epgval>(config-oob-epg)# contract provider <contractName>

contract provider <WORD>

Description: Add a provider contract

Syntax:

Whitelist contract to provideWORD


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match prefix-list <WORD>(config-leaf-vrf-route-map-match)# contract provider <WORD>



controller-groupcontroller-group

Description: Controller Upgrade Configuration Mode


Command Path:

# configure [['terminal', 't']](config)# firmware(config-firmware)# controller-group


C Commandscontroller-group

controllercontroller

Description: Configure Controller Node

Syntax:

arg


Command Path:

# configure [['terminal', 't']](config)# controller


C Commandscontroller

costcost <NUMBER>

Description: Set OSPF cost for the interface

Syntax:

OSPF cost. Number range from=0 to=65535<0-65535>


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf interface-policy <WORD> tenant <WORD>(config-interface-policy)# cost <NUMBER>


C Commandscost

countrycountry <WORD>

Description: Set The two-letter ISO code for the country where the organization is located.

Syntax:

The two-letter ISO code for the country where the organization is located<WORD>

Command Mode: csr : A csr mode to create and hold an SSL certificate

Command Path:

# configure [['terminal', 't']](config)# crypto keyring <WORD>(config-keyring)# csr(config-csr)# country <WORD>


C Commandscountry

crypto aescrypto aes

Description: AES encryption configuration


Command Path:

# configure [['terminal', 't']](config)# crypto aes


C Commandscrypto aes

crypto cacrypto ca <WORD>

Description: Configure certificate authority related information

Syntax:

Trustpoint label (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# crypto ca <WORD>


C Commandscrypto ca

crypto keyringcrypto keyring <WORD>

Description: A keyring mode to create and hold an SSL certificate

Syntax:

Provide a keyring nameWORD


Command Path:

# configure [['terminal', 't']](config)# crypto keyring <WORD>


C Commandscrypto keyring

crypto webtokencrypto webtoken

Description: The cryptographic data used for generating and verifying web tokens.


Command Path:

# configure [['terminal', 't']](config)# crypto webtoken


C Commandscrypto webtoken

csrcsr

Description: A csr mode to create and hold an SSL certificate


Command Path:

# configure [['terminal', 't']](config)# crypto keyring <WORD>(config-keyring)# csr


C Commandscsr

customer-idcustomer-id <WORD>

Description: The customer id

Syntax:

The customer id (Max Size 512) surrounded by quotesWORD


Command Path:

# configure [['terminal', 't']](config)# callhome common(config-callhome)# destination-profile(config-callhome-destnprof)# customer-id <WORD>


C Commandscustomer-id

D Commands

• data, page 135

• dead-interval, page 136

• debug log reset, page 137

• debug log set, page 138

• decommission controller, page 139

• decommission switch, page 140

• default-information, page 141

• default-originate, page 142

• deploy-epg tenant application epg type, page 143

• deploy-epg tenant application epg vlan, page 144

• deployment-mode, page 145

• descr, page 146

• description, page 147

• destination-profile, page 160

• destination, page 161

• destination destip, page 163

• destination interface, page 164

• destination tenant, page 165

• dhcp option, page 167

• dhcp relay policy, page 168

• dhparam, page 169

• direction, page 170

• disable-connected-check, page 173

• disable-peer-as-check, page 174


• distance, page 175

• dns, page 177

• dnssearchsuffix, page 178

• dnsservers, page 179

• dnssuffix, page 180

• domain, page 181

• dsr-vip, page 182

• dsr, page 183


D Commands

datadata <LINE>

Description: Set A user public key in PEM format.

Syntax:

user public key in PEM format in quotes (Max Size None)LINE

Command Mode: ssh-key : Update ssh key for the user for ssh authentication

Command Path:

# configure [['terminal', 't']](config)# username <WORD>(config-username)# ssh-key <WORD>(config-ssh-key)# data <LINE>

data <CERTIFICATE>

Description: Set PEM encoded certificate

Syntax:

PEM encoded certificate in quotesCERTIFICATE

Command Mode: certificate : Create AAA user certificate in X.509 format.

Command Path:

# configure [['terminal', 't']](config)# username <WORD>(config-username)# certificate <WORD>(config-certificate)# data <CERTIFICATE>


D Commandsdata

dead-intervaldead-interval <NUMBER>

Description: Set the interval between hello packets from a neighbor before the router declares the neighboras down

Syntax:

Interval in seconds. Number range from=1 to=65535<1-65535>


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf interface-policy <WORD> tenant <WORD>(config-interface-policy)# dead-interval <NUMBER>


D Commandsdead-interval

debug log resetdebug <node-name> <process> log reset

Description: Reset the log levels to default log level

Syntax:

Node name<node-name>

Process name<process>


Command Path:

# debug <node-name> <process> log reset


D Commandsdebug log reset

debug log setdebug <node-name> <process> log set <topic> <level>

Description: Set log level for a topic

Syntax:



Topic name<topic>

Level name<level>


Command Path:

# debug <node-name> <process> log set <topic> <level>


D Commandsdebug log set

decommission controllerdecommission controller <NUMBER>

Description: Decommission controller

Syntax:

Controller ID. Number range from=1 to=32<1-32>


Command Path:

# configure [['terminal', 't']](config)# decommission controller <NUMBER>


D Commandsdecommission controller

decommission switchdecommission switch <NUMBER> [remove-from-controller]

Description: Decommission switch

Syntax:

Node ID. Number range from=101 to=4000<101-4000>

(Optional) Remove the switch from controller (optional)remove-from-controller


Command Path:

# configure [['terminal', 't']](config)# decommission switch <NUMBER> [remove-from-controller]


D Commandsdecommission switch

default-informationdefault-information originate [always]

Description: Control origination of a default route

Syntax:

Originate a default routeoriginate

(Optional) Always advertise default routealways


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router eigrp default(config-eigrp)# vrf member tenant <WORD> vrf <WORD>(config-eigrp-vrf)# default-information originate [always]

default-information originate [always]

Description: Control origination of a default route

Syntax:

Originate a default routeoriginate

(Optional) Always advertise default routealways


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# default-information originate [always]


D Commandsdefault-information

default-originatedefault-originate

Description: Originate a default toward this peer


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [l3out <WORD>](config-leaf-bgp-vrf-neighbor)# default-originate


D Commandsdefault-originate

deploy-epg tenant application epg typedeploy-epg tenant <WORD> application <WORD> epg <WORD> type micro-segmented

Description: Deploy micro-segmented AEPg on leaf

Syntax:

Tenant hosting the AEPg to deploytenant

Tenant hosting the AEPg to deploy (Max Size 63)WORD

Application hosting the AEPg to deployapplication

Application Name (Max Size 64)WORD

AEPg to be deployed on the leafepg

EPg that uses the statically enabled Encap. (Max Size 64)WORD

micro-segmented AEPgmicro-segmented

Command Mode: leaf : Configure Leaf Node

Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# deploy-epg tenant <WORD> application <WORD> epg <WORD> type micro-segmented


D Commandsdeploy-epg tenant application epg type

deploy-epg tenant application epg vlandeploy-epg tenant <WORD> application <WORD> epg <WORD> vlan <NUMBER> vlan-domain member<WORD>

Description: Deploy regular AEPg on leaf

Syntax:

Tenant hosting the AEPg to deploytenant

Tenant hosting the AEPg to deploy (Max Size 63)WORD

Application hosting the AEPg to deployapplication


AEPg to be deployed on the leafepg

EPg that uses the statically enabled Encap. (Max Size 64)WORD

Encapsulation Vlan. Number range from=1 to=4094<1-4094>

Vlan Domain for Encapsulation Vlanvlan-domain

Vlan Domain for Encapsulation Vlanmember

vlan-domain to use to validate encapsulation vlan. (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# deploy-epg tenant <WORD> application <WORD> epg <WORD> vlan <NUMBER>vlan-domain member <WORD>


D Commandsdeploy-epg tenant application epg vlan

deployment-modedeployment-mode <WORD>

Description: Set zone deployment mode

Syntax:

Zone Deployment ModeWORD

Command Mode: zone : Create zone policy

Command Path:

# configure [['terminal', 't']](config)# zones(config-zones)# zone <WORD>(config-zone)# deployment-mode <WORD>


D Commandsdeployment-mode

descrdescr <WORD>

Description: RADIUS server descr for authentication

Syntax:

descr for authentication (Max Size 128)<WORD>

Command Mode: radius-server host : RADIUS server's DNS name or its IP address

Command Path:

# configure [['terminal', 't']](config)# radius-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# descr <WORD>


D Commandsdescr

descriptiondescription <description>

Description: Add a description to a power supply redundancy policy

Syntax:

Power supply redundancy policy description string<description>

Command Mode: power : Create a power supply redundancy policy

Command Path:

# configure [['terminal', 't']](config)# power redundancy-policy <WORD>(config-power)# description <description>

description <LINE>

Description: Set description

Syntax:

Set description, use single quotes with spaces ex: 'my descr' (Max Size128)

LINE

CommandMode: rbac security-domain : Create AAA security domain for processing authentication requests.

Command Path:

# configure [['terminal', 't']](config)# rbac security-domain <WORD>(config-security-domain)# description <LINE>

description <WORD>

Description: The description of callhome destination-profile

Syntax:

The description (Max Size 128) surrounded by single quotesWORD


Command Path:

# configure [['terminal', 't']](config)# callhome common(config-callhome)# destination-profile


D Commandsdescription

(config-callhome-destnprof)# description <WORD>

description <WORD>

Description: Add switch-group description

Syntax:

Description string, surrounded by single quotes if with spaces ex: 'Mydescr' (Max Size 128)

WORD

Command Mode: switch-group : Create switch firmware upgrade policy

Command Path:

# configure [['terminal', 't']](config)# firmware(config-firmware)# switch-group <WORD>(config-firmware-switch)# description <WORD>

description <STRING>

Description: Configure STP description

Syntax:

DescriptionSTRING

Command Mode: region : STP MST region configuration mode

Command Path:

# configure [['terminal', 't']](config)# spanning-tree mst configuration(config-stp)# region <WORD>(config-stp-region)# description <STRING>

description <WORD>

Description: Description string, surrounded by single quotes if with spaces ex: 'My descr'

Syntax:


WORD

Command Mode: template dhcp relay : Create a DHCP Relay policy

Command Path:

# configure [['terminal', 't']](config)# template dhcp relay policy <WORD>



(config-template-dhcp-relay)# description <WORD>

description <description>

Description: Update Policy-Group Template description

Syntax:

<description>


Command Path:

# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# description <description>

description <description>

Description: Update Port-Channel Template description

Syntax:

<description>


Command Path:

# configure [['terminal', 't']](config)# template port-channel <WORD>(config-if)# description <description>

description <WORD>

Description: Add a description string to a tenant, surrounded by single quotes if with spaces ex: 'My descr'

Syntax:


WORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# description <WORD>



description <WORD>

Description: Add a description on a contract, surrounded by single quotes if with spaces ex: 'My descr'

Syntax:

Contract description, surrounded by single quotes if with spaces ex:'My descr' (Max Size 128)

WORD

Command Mode: contract : Configure binary contracts between Application EPGs

Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# contract <WORD> [type <type>](config-tenant-contract)# description <WORD>

description <WORD>

Description: Add a description on a subject, surrounded by single quotes if with spaces ex: 'My descr'

Syntax:

Subject description, surrounded by single quotes if with spaces ex: 'Mydescr' (Max Size 128)

WORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# contract <WORD> [type <type>](config-tenant-contract)# subject <WORD>(config-tenant-contract-subj)# description <WORD>

description <WORD>

Description: Add a description on a vrf, surrounded by single quotes if with spaces ex: 'My descr'

Syntax:

VRF description, surrounded by single quotes if with spaces ex: 'Mydescr' (Max Size 128)

WORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>



(config-tenant-vrf)# description <WORD>

description <WORD>

Description: Add a description on an application, surrounded by single quotes if with spaces ex: 'My descr'

Syntax:


WORD

Command Mode: application : application configuration mode

Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# description <WORD>

description <WORD>

Description: Add a description on an epg, surrounded by single quotes if with spaces ex: 'My descr'

Syntax:


WORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# description <WORD>

description <epgDescr>

Description: Add a description on an epg

Syntax:

<epgDescr>




Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# inband-mgmt epg <WORD>(config-inb-epg)# description <epgDescr>

description <WORD>

Description:Add a description on a bridge-domain, surrounded by single quotes if with spaces ex: 'My descr'

Syntax:

Bridge-domain description, surrounded by single quotes if with spacesex: 'My descr' (Max Size 128)

WORD

Command Mode: interface : Configuration for interface bridge-domain

Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# description <WORD>

description <WORD>

Description: Add a description on an epg, surrounded by single quotes if with spaces ex: 'My descr'

Syntax:


WORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l2 epg <WORD>(config-tenant-l2ext-epg)# description <WORD>

description <epgDescr>

Description: Add a description on an epg

Syntax:

<epgDescr>




Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# oob-mgmt epg <epgval>(config-oob-epg)# description <epgDescr>

description <WORD>

Description: Description string, surrounded by single quotes if with spaces ex: 'My descr'

Syntax:


WORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template dhcp relay policy <WORD>(config-tenant-template-dhcp-relay)# description <WORD>

description <LINE>

Description: Update igmp snooping policy description

Syntax:

IGMP snooping policy description, use single quotes with spaces ex:'my descr' (Max Size 128)

LINE

Command Mode: template ip igmp snooping policy : Create an IGMP snooping policy

Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip igmp snooping policy <WORD>(config-tenant-template-ip-igmp-snooping)# description <LINE>

description <LINE>

Description: Update Leaf Interface Profile description

Syntax:

Leaf-If-Profile description, use single quotes with spaces ex: 'my descr'(Max Size 128)

LINE



Command Mode: leaf-interface-profile : Create Leaf Interface Profile

Command Path:

# configure [['terminal', 't']](config)# leaf-interface-profile <WORD>(config-leaf-if-profile)# description <LINE>

description <LINE>

Description: Update Leaf Interface Group description

Syntax:

Leaf-If-group description, use single quotes with spaces ex: 'my descr'(Max Size 128)

LINE


Command Path:

# configure [['terminal', 't']](config)# leaf-interface-profile <WORD>(config-leaf-if-profile)# leaf-interface-group <WORD>(config-leaf-if-group)# description <LINE>

description <LINE>

Description: Update Leaf Profile description

Syntax:

Leaf-Profile description, use single quotes with spaces ex: 'my descr'(Max Size 128)

LINE

Command Mode: leaf-profile : Configure Leaf Profile

Command Path:

# configure [['terminal', 't']](config)# leaf-profile <WORD>(config-leaf-profile)# description <LINE>

description <LINE>

Description: Update Leaf Group description

Syntax:

Leaf-group description, use single quotes with spaces ex: 'my descr'(Max Size 128)

LINE



Command Mode: leaf-group : Configure Leaf Group

Command Path:

# configure [['terminal', 't']](config)# leaf-profile <WORD>(config-leaf-profile)# leaf-group <WORD>(config-leaf-group)# description <LINE>

description <LINE>

Description: Update Fex Profile description

Syntax:

Fex-Profile description, use single quotes with spaces ex: 'my descr'(Max Size 128)

LINE

Command Mode: fex-profile : Configure Fex Profile

Command Path:

# configure [['terminal', 't']](config)# fex-profile <WORD>(config-fex-profile)# description <LINE>

description <LINE>

Description: Update Fex Interface Group description

Syntax:

Fex-If-group description, use single quotes with spaces ex: 'my descr'(Max Size 128)

LINE


Command Path:

# configure [['terminal', 't']](config)# fex-profile <WORD>(config-fex-profile)# fex-interface-group <WORD>(config-fex-if-group)# description <LINE>

description <LINE>

Description: Update interface vlan description

Syntax:

interface vlan description, use single quotes with spaces ex: 'my descr'(Max Size 128)

LINE




Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# description <LINE>

description <LINE>

Description: Update Interface description

Syntax:

Interface description, use single quotes with spaces ex: 'my descr' (MaxSize 128)

LINE


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# description <LINE>

description <LINE>

Description: Update Port-Channel description

Syntax:

Port-Channel description, use single quotes with spaces ex: 'my descr'(Max Size 128)

LINE


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# description <LINE>

description <LINE>

Description: Update VPC description

Syntax:

VPC description, use single quotes with spaces ex: 'my descr' (MaxSize 128)

LINE




Command Path:

# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# description <LINE>

description <LINE>

Description: Add description to the session

Syntax:

Session description, use single quotes with spaces ex: 'my descr' (MaxSize 128)

LINE

Command Mode: monitor access : Configue monitor session for access interfaces

Command Path:

# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# description <LINE>

description <LINE>


Syntax:


LINE

Command Mode: monitor fabric : Configue monitor session for fabric interfaces

Command Path:

# configure [['terminal', 't']](config)# monitor fabric session <session_name>(config-monitor-fabric)# description <LINE>

description <LINE>


Syntax:


LINE



Command Mode: monitor tenant : Configue monitor session for tenant EPGs

Command Path:

# configure [['terminal', 't']](config)# monitor tenant <tenant_name> session <session_name>(config-monitor-tenant)# description <LINE>

description <LINE>


Syntax:


LINE

Command Mode: monitor virtual : Configure monitor session for virtual switches

Command Path:

# configure [['terminal', 't']](config)# monitor virtual session <WORD>(config-monitor-virtual)# description <LINE>

description <STRING>

Description: Configure schedule description

Syntax:

Scheduler descriptionSTRING


Command Path:

# configure [['terminal', 't']](config)# scheduler fabric|controller schedule <WORD>(config-scheduler)# description <STRING>

description <WORD>

Description: Add description for this server-group

Syntax:

Description (Max Size 128) surrounded by single quotesWORD




Command Path:

# configure [['terminal', 't']](config)# logging server-group <WORD>(config-logging)# description <WORD>

description <WORD>

Description: Add zone description

Syntax:


WORD


Command Path:

# configure [['terminal', 't']](config)# zones(config-zones)# zone <WORD>(config-zone)# description <WORD>



destination-profiledestination-profile

Description: Configure destination profile Parameters

Command Mode: callhome : Callhome common policy configuration mode

Command Path:

# configure [['terminal', 't']](config)# callhome common(config-callhome)# destination-profile


D Commandsdestination-profile

destinationdestination <WORD>

Description: Configure destination Parameters

Syntax:

The name (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# callhome common(config-callhome)# destination-profile(config-callhome-destnprof)# destination <WORD>

destination tenant <tenant_name> application <application_name> epg <epg_name> destination-ip <A.B.C.D>source-ip-prefix <A.B.C.D/M>

Description: Configure monitor remote destination

Syntax:

tenanttenant

tenant name (Max Size 63)tenant_name

applicationapplication

application nameapplication_name

epgepg

epg nameepg_name

destination IPdestination-ip

IP addressA.B.C.D

source IP prefixsource-ip-prefix

IP adddress prefixA.B.C.D/M



D Commandsdestination

Command Path:

# configure [['terminal', 't']](config)# monitor fabric session <session_name>(config-monitor-fabric)# destination tenant <tenant_name> application <application_name>epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M>

destination tenant <tenant_name> application <application_name> epg <epg_name> destination-ip <A.B.C.D>source-ip-prefix <A.B.C.D/M>


Syntax:

tenanttenant



application name (Max Size 64)application_name

epgepg

epg name (Max Size 64)epg_name


IP addressA.B.C.D




Command Path:

# configure [['terminal', 't']](config)# monitor tenant <tenant_name> session <session_name>(config-monitor-tenant)# destination tenant <tenant_name> application <application_name>epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M>


D Commandsdestination

destination destipdestination destip <A.B.C.D>


Syntax:

Destination IP addressA.B.C.D


Command Path:

# configure [['terminal', 't']](config)# monitor virtual session <WORD>(config-monitor-virtual)# destination destip <A.B.C.D>


D Commandsdestination destip

destination interfacedestination interface ethernet <ethernet> leaf <leaf Id>

Description: Configure monitor local destination

Syntax:

ethernetethernet

<ethernet><ethernet>

leafleaf

leaf Id<leaf Id>


Command Path:

# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# destination interface ethernet <ethernet> leaf <leaf Id>


D Commandsdestination interface

destination tenantdestination tenant <tenant_name> application <application_name> epg <epg_name> destination-ip <A.B.C.D>source-ip-prefix <A.B.C.D/M>


Syntax:




epgepg



IP addressA.B.C.D




Command Path:

# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# destination tenant <tenant_name> application <application_name>epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M>

destination tenant <WORD> application <WORD> epg <WORD> macE.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE

Description: Configure monitor local destination

Syntax:

tenant name (Max Size 63)WORD


application name (Max Size 64)WORD

epgepg


D Commandsdestination tenant

epg name (Max Size 64)WORD

macmac






Command Path:

# configure [['terminal', 't']](config)# monitor virtual session <WORD>(config-monitor-virtual)# destination tenant <WORD> application <WORD> epg <WORD> macE.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE


D Commandsdestination tenant

dhcp optiondhcp option <WORD> id <NUMBER> data <WORD>

Description: Add or modify an existing DHCP option when relayed from the server to the client

Syntax:

Name of the option to add (Max Size 64)WORD

ID of the optionid

ID of the option. Number range from=0 to=255<0-255>

Body of the Option TLV as hex stringdata

Body of the Option TLV as hex string, surrounded by single quotes ex:'foo*' (Max Size 256)

WORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# dhcp option <WORD> id <NUMBER> data <WORD>


D Commandsdhcp option

dhcp relay policydhcp relay policy tenant|infra <WORD> [option <WORD>]

Description: Associate the BD with a DHCP Relay policy

Syntax:

Select DHCP policies from current Tenanttenant

Select DHCP policy from infrainfra

Name of the DHCP relay policy (Max Size 64)WORD

(Optional) Name of the DHCP option policy (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# dhcp relay policy tenant|infra <WORD> [option <WORD>]


D Commandsdhcp relay policy

dhparamdhparam <dhparam>

Description: Set the DH parameter used for HTTPS communication service

Syntax:

DH Param as comma separated values like val1,val2,..valNdhparam


Command Path:

# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# https(config-https)# dhparam <dhparam>


D Commandsdhparam

directiondirection both|rx|tx

Description:Monitor direction

Syntax:

bothboth

rxrx

txtx

Command Mode: source interface ethernet : Configure monitor for ethernet access interfaces

Command Path:

# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# source interface ethernet <ethernet> leaf <leaf Id>(config-monitor-access-source)# direction both|rx|tx

direction both|rx|tx


Syntax:

bothboth

rxrx

txtx

Command Mode: source interface port-channel : Configure monitor for port-channel interfaces

Command Path:

# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# source interface port-channel <port-channel list> leaf <leaf Id>[fex <fex Id>](config-monitor-access-source)# direction both|rx|tx



Syntax:


D Commandsdirection

bothboth

rxrx

txtx

Command Mode: source interface vpc : Configure monitor for VPC interfaces

Command Path:

# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# source interface vpc <vpc list> leaf <leaf Id1> <leaf Id2> [fex<fex Ids>](config-monitor-access-source)# direction both|rx|tx



Syntax:

bothboth

rxrx

txtx

Command Mode: source interface ethernet : Configure monitor for ethernet fabric interfaces

Command Path:

# configure [['terminal', 't']](config)# monitor fabric session <session_name>(config-monitor-fabric)# source interface ethernet <ethernet> switch <switch Id>(config-monitor-fabric-source)# direction both|rx|tx



Syntax:

bothboth

rxrx

txtx

Command Mode: source application : Configure EPG as monitor source


D Commandsdirection

Command Path:

# configure [['terminal', 't']](config)# monitor tenant <tenant_name> session <session_name>(config-monitor-tenant)# source application <application_name> epg <epg_name>(config-monitor-tenant-source)# direction both|rx|tx


Description: Configure monitor source direction

Syntax:

bothboth

rxrx

txtx

Command Mode: source : Configure monitor virtual source

Command Path:

# configure [['terminal', 't']](config)# monitor virtual session <WORD>(config-monitor-virtual)# source tenant <WORD> application <WORD> epg <WORD> [mac <E.E.EEE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >](config-monitor-virtual-source)# direction both|rx|tx


D Commandsdirection

disable-connected-checkdisable-connected-check

Description: Disable check for directly connected peer


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [l3out <WORD>](config-leaf-bgp-vrf-neighbor)# disable-connected-check


D Commandsdisable-connected-check

disable-peer-as-checkdisable-peer-as-check

Description: Disable checking of peer AS-number while advertising


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [l3out <WORD>](config-leaf-bgp-vrf-neighbor)# disable-peer-as-check


D Commandsdisable-peer-as-check

distancedistance <NUMBER>

Description: Set OSPF Policy Preferred Administrative Distance

Syntax:

Distance Value. Number range from=1 to=255<1-255>


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf vrf-policy <WORD> tenant <WORD>(config-vrf-policy)# distance <NUMBER>

distance <NUMBER> <NUMBER> <NUMBER>

Description: Configure BGP Address Family Distance Properties

Syntax:

The administrative distance of eBGP routes. Number range from=1to=255

<1-255>

The administrative distance of iBGP routes. Number range from=1to=255

<1-255>

The administrative distance of local routes. Number range from=1to=255

<1-255>

Command Mode: template bgp address-family : Configure Router BGP Address Family Templates

Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template bgp address-family <WORD> tenant <WORD>(config-bgp-af)# distance <NUMBER> <NUMBER> <NUMBER>

distance <NUMBER> <NUMBER>

Description: Set EIGRP adminstrative distances

Syntax:

The administrative distance preference for internal routes. Number rangefrom=1 to=255

<1-255>


D Commandsdistance

The administrative distance preference for external routes. Numberrange from=1 to=255

<1-255>

Command Mode: template eigrp vrf-policy : Configure EIGRP VRF policy templates

Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template eigrp vrf-policy <WORD> tenant <WORD>(config-template-eigrp-vrf-pol)# distance <NUMBER> <NUMBER>

distance <NUMBER> <NUMBER>

Description: Set EIGRP adminstrative distances

Syntax:

The administrative distance preference for internal routes. Number rangefrom=1 to=255

<1-255>

The administrative distance preference for external routes. Numberrange from=1 to=255

<1-255>

Command Mode: address-family : EIGRP Policy Address Family

Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router eigrp default(config-eigrp)# vrf member tenant <WORD> vrf <WORD>(config-eigrp-vrf)# address-family ipv4|ipv6 unicast(config-address-family)# distance <NUMBER> <NUMBER>


D Commandsdistance

dnsdns

Description: Configure default dns policy


Command Path:

# configure [['terminal', 't']](config)# dns

dns label <WORD>

Description: Add a DNS policy to the VRF

Syntax:

Dns policy to applylabel

Dns policy to apply (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# dns label <WORD>


D Commandsdns

dnssearchsuffixdnssearchsuffix <suffix>

Description: Add DNS search suffix

Syntax:

suffixsuffix

Command Mode: microsoft : Configure static ip pool

Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# microsoft static-ip-pool <name> gateway <gwAddress>(config-tenant-app-epg-ms-ip-pool)# dnssearchsuffix <suffix>


D Commandsdnssearchsuffix

dnsserversdnsservers <DNS server list>

Description: Add dns servers

Syntax:

DNS server listDNS server list


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# microsoft static-ip-pool <name> gateway <gwAddress>(config-tenant-app-epg-ms-ip-pool)# dnsservers <DNS server list>


D Commandsdnsservers

dnssuffixdnssuffix <suffix>

Description: Add dns suffix

Syntax:

suffixsuffix


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# microsoft static-ip-pool <name> gateway <gwAddress>(config-tenant-app-epg-ms-ip-pool)# dnssuffix <suffix>


D Commandsdnssuffix

domaindomain <WORD>

Description: Create the AAA domain to which the user belongs.

Syntax:

Domain for the userWORD


Command Path:

# configure [['terminal', 't']](config)# username <WORD>(config-username)# domain <WORD>

domain <WORD> [default]

Description: Configure the domains for dns servers

Syntax:

Domain in the format^([a-zA-Z]|[a-zA-Z][a-zA-Z0-9]|[a-zA-Z][a-zA-Z0-9-.]{0,253}[a-zA-Z0-9])$

WORD

(Optional) Set the default domain for dns serversdefault


Command Path:

# configure [['terminal', 't']](config)# dns(config-dns)# domain <WORD> [default]


D Commandsdomain

dsr-vipdsr-vip <WORD>

Description: Configure DSR VIP For a L4-L7 Graph Connector.

Syntax:

Enter VIP address (Max Size None)WORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 graph <WORD> [contract <contract-option>](config-graph)# service <WORD> [device-cluster-tenant <WORD>] [device-cluster <WORD>] [mode<Available Modes>](config-service)# connector <WORD> [cluster-interface <WORD>](config-connector)# dsr-vip <WORD>


D Commandsdsr-vip

dsrdsr virtual-ip-address <address> [description <description>]

Description: Add a DSR virtual IP address

Syntax:

Virtual IP address of load balancervirtual-ip-address

IP address<address>

(Optional) descriptiondescription


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# dsr virtual-ip-address <address> [description <description>]


D Commandsdsr


D Commandsdsr

E Commands

• ebgp-multihop, page 187

• echo-address, page 188

• echo-mode, page 189

• echo-rx-interval, page 190

• email-addr, page 191

• email-contact, page 192

• email, page 193

• enable-ssl, page 194

• encryption, page 195

• end, page 196

• endpoint, page 197

• endpoint loop-detect action bd-learn-disable, page 198

• endpoint loop-detect action port-disable, page 199

• endpoint loop-detect enable, page 200

• endpoint loop-detect factor, page 201

• endpoint loop-detect interval, page 202

• endpoint move-detection, page 203

• endpoint retention bounce-age-interval, page 204

• endpoint retention hold-interval, page 205

• endpoint retention local-age-interval, page 206

• endpoint retention move-frequency, page 207

• endpoint retention policy, page 208

• endpoint retention remote-age-interval, page 209

• enforce-subnet-learning, page 210


• epg, page 211

• eraseconfig, page 212

• errdisable recovery cause bpduguard, page 213

• errdisable recovery cause ep-move, page 214

• errdisable recovery cause mcp-loop, page 215

• errdisable recovery interval, page 216

• erspan-id, page 217

• exec, page 219

• exit, page 220

• expiration, page 221

• expires, page 222

• export, page 223

• external-l2, page 224

• external-l3, page 225

• external-l3 epg, page 226


E Commands

ebgp-multihopebgp-multihop <NUMBER>

Description: Specify multihop TTL for remote peer

Syntax:

EBGP TTL value. Number range from=1 to=255<1-255>


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [l3out <WORD>](config-leaf-bgp-vrf-neighbor)# ebgp-multihop <NUMBER>


E Commandsebgp-multihop

echo-addressecho-address <arg>

Description: Configure BFD ECHO-SRC-ADDRESS value

Syntax:

arg

Command Mode: template bfd : BFD group of commands

Command Path:

# configure [['terminal', 't']](config)# template bfd ip|ipv6 <WORD>(config-bfd)# echo-address <>


E Commandsecho-address

echo-modeecho-mode enable

Description: Enable Echo mode

Syntax:

Enable Echo modeenable

Command Mode: template bfd : Configure BFD Interface Policy Templates

Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template bfd <WORD> tenant <WORD>(config-template-bfd-pol)# echo-mode enable


E Commandsecho-mode

echo-rx-intervalecho-rx-interval <NUMBER>

Description: Configure BFD ECHO-RX-INTERVAL value in milliseconds

Syntax:

BFD interval. Number range from=50 to=999<interval>


Command Path:

# configure [['terminal', 't']](config)# template bfd ip|ipv6 <WORD>(config-bfd)# echo-rx-interval <NUMBER>

echo-rx-interval <NUMBER>

Description: Configure Echo Rx Interval in milliseconds

Syntax:

Echo Rx Interval. Number range from=50 to=999<interval>


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template bfd <WORD> tenant <WORD>(config-template-bfd-pol)# echo-rx-interval <NUMBER>


E Commandsecho-rx-interval

email-addremail-addr <WORD>

Description: Configure the e-mail address

Syntax:

The email address (Max Size None)WORD

Command Mode: destination : Configure destination Parameters

Command Path:

# configure [['terminal', 't']](config)# callhome common(config-callhome)# destination-profile(config-callhome-destnprof)# destination <WORD>(config-callhome-destnprof-destn)# email-addr <WORD>


E Commandsemail-addr

email-contactemail-contact <WORD>

Description: The contact e-mail address

Syntax:

Contract e-mail address (Max Size 512)WORD


Command Path:

# configure [['terminal', 't']](config)# callhome common(config-callhome)# destination-profile(config-callhome-destnprof)# email-contact <WORD>


E Commandsemail-contact

emailemail <WORD>

Description: Set The email address of the locally-authenticated user.

Syntax:

email address of the locally-authenticated userWORD


Command Path:

# configure [['terminal', 't']](config)# username <WORD>(config-username)# email <WORD>

email <WORD>

Description: Set The email address of the organization contact person.

Syntax:

email address (Max Size 40)<WORD>


Command Path:

# configure [['terminal', 't']](config)# crypto keyring <WORD>(config-keyring)# csr(config-csr)# email <WORD>


E Commandsemail

enable-sslenable-ssl

Description: enabling an SSL connection with the LDAP provider


Command Path:

# configure [['terminal', 't']](config)# ldap-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# enable-ssl


E Commandsenable-ssl

encryptionencryption

Description: Enable AES Encryption


Command Path:

# configure [['terminal', 't']](config)# crypto aes(config-aes)# encryption


E Commandsencryption

endend

Description: Exit to the exec mode


Command Path:

# end


E Commandsend

endpointendpoint retention <WORD>

Description: Specify an endpoint retention policy for this VRF

Syntax:

Specify an endpoint retention policy for this VRFretention

Endpoint Retention Policy (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# endpoint retention <WORD>


E Commandsendpoint

endpoint loop-detect action bd-learn-disableendpoint loop-detect action bd-learn-disable

Description: Configure EP Loop Protection Action to BD-Learn-Disable


Command Path:

# configure [['terminal', 't']](config)# endpoint loop-detect action bd-learn-disable


E Commandsendpoint loop-detect action bd-learn-disable

endpoint loop-detect action port-disableendpoint loop-detect action port-disable

Description: Configure EP Loop Protection Action to Port-Disable


Command Path:

# configure [['terminal', 't']](config)# endpoint loop-detect action port-disable


E Commandsendpoint loop-detect action port-disable

endpoint loop-detect enableendpoint loop-detect enable

Description: Enable/Disable Endpoint Loop-Detect Policy


Command Path:

# configure [['terminal', 't']](config)# endpoint loop-detect enable


E Commandsendpoint loop-detect enable

endpoint loop-detect factorendpoint loop-detect factor <NUMBER>

Description: Configure End Point Loop Detection Factor

Syntax:

End Point Loop ProtectionMultipication Factor. Number range from=1to=255

<1-255>


Command Path:

# configure [['terminal', 't']](config)# endpoint loop-detect factor <NUMBER>


E Commandsendpoint loop-detect factor

endpoint loop-detect intervalendpoint loop-detect interval <NUMBER>

Description: Configure End Point Loop Detection Interval

Syntax:

End Point Loop Detection Interval. Number range from=30 to=300<30-300>


Command Path:

# configure [['terminal', 't']](config)# endpoint loop-detect interval <NUMBER>


E Commandsendpoint loop-detect interval

endpoint move-detectionendpoint move-detection <WORD>

Description: Endpoint Move detection Mode

Syntax:

Endpoint Move detection ModeWORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>(config-tenant-bd)# endpoint move-detection <WORD>


E Commandsendpoint move-detection

endpoint retention bounce-age-intervalendpoint retention bounce-age-interval x in <0-0> or <150-65535>

Description: Set the bounce age interval for endpoints

Syntax:

Set the Bounce Age Interval, use 0 for infinitex in <0-0> or <150-65535>


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>(config-tenant-bd)# endpoint retention bounce-age-interval x in <0-0> or <150-65535>

endpoint retention bounce-age-interval x in <0-0> or <150-65535>

Description: Set the bounce age interval for endpoints

Syntax:

Set the Bounce Age Interval, use 0 for infinitex in <0-0> or <150-65535>

Command Mode: template endpoint retention policy : Configure an endpoint retention policy

Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template endpoint retention policy <WORD>(config-tenant-template-endpoint-retention)# endpoint retention bounce-age-interval x in<0-0> or <150-65535>


E Commandsendpoint retention bounce-age-interval

endpoint retention hold-intervalendpoint retention hold-interval <NUMBER>

Description: Set the hold interval for endpoints

Syntax:

Set the Hold Interval. Number range from=5 to=65535<5-65535>


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>(config-tenant-bd)# endpoint retention hold-interval <NUMBER>

endpoint retention hold-interval <NUMBER>

Description: Set the hold interval for endpoints

Syntax:

Set the Hold Interval. Number range from=5 to=65535<5-65535>


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template endpoint retention policy <WORD>(config-tenant-template-endpoint-retention)# endpoint retention hold-interval <NUMBER>


E Commandsendpoint retention hold-interval

endpoint retention local-age-intervalendpoint retention local-age-interval x in <0-0> or <120-65535>

Description: Set the local endpoint age interval

Syntax:

Set the local endpoint age interval, use 0 for infinitex in <0-0> or <120-65535>


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>(config-tenant-bd)# endpoint retention local-age-interval x in <0-0> or <120-65535>

endpoint retention local-age-interval x in <0-0> or <120-65535>

Description: Set the local endpoint age interval

Syntax:

Set the local endpoint age interval, use 0 for infinitex in <0-0> or <120-65535>


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template endpoint retention policy <WORD>(config-tenant-template-endpoint-retention)# endpoint retention local-age-interval x in<0-0> or <120-65535>


E Commandsendpoint retention local-age-interval

endpoint retention move-frequencyendpoint retention move-frequency <NUMBER>

Description: Set the move frequency

Syntax:

Set the move frequency. Number range from=0 to=65535<0-65535>


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>(config-tenant-bd)# endpoint retention move-frequency <NUMBER>

endpoint retention move-frequency <NUMBER>

Description: Set the move frequency

Syntax:

Set the move frequency. Number range from=0 to=65535<0-65535>


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template endpoint retention policy <WORD>(config-tenant-template-endpoint-retention)# endpoint retention move-frequency <NUMBER>


E Commandsendpoint retention move-frequency

endpoint retention policyendpoint retention policy <WORD>

Description: Associate the BD with an endpoint retention policy

Syntax:

Name of the endpoint retention policy to set (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>(config-tenant-bd)# endpoint retention policy <WORD>


E Commandsendpoint retention policy

endpoint retention remote-age-intervalendpoint retention remote-age-interval x in <0-0> or <120-65535>

Description: Set the remote endpoint age interval

Syntax:

Remote endpoint age interval, use 0 for infinitex in <0-0> or <120-65535>


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>(config-tenant-bd)# endpoint retention remote-age-interval x in <0-0> or <120-65535>

endpoint retention remote-age-interval x in <0-0> or <120-65535>

Description: Set the remote endpoint age interval

Syntax:

Remote endpoint age interval, use 0 for infinitex in <0-0> or <120-65535>


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template endpoint retention policy <WORD>(config-tenant-template-endpoint-retention)# endpoint retention remote-age-interval x in<0-0> or <120-65535>


E Commandsendpoint retention remote-age-interval

enforce-subnet-learningenforce-subnet-learning

Description: Subnet learning enforcement


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>(config-tenant-bd)# enforce-subnet-learning


E Commandsenforce-subnet-learning

epgepg <WORD> [type <WORD>]

Description: AEPg configuration mode

Syntax:

Application EPG name (Max Size 64)WORD

(Optional) Specify EPG typeWORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>]


E Commandsepg

eraseconfigeraseconfig

Description: Erase config and reboot


Command Path:

# eraseconfig


E Commandseraseconfig

errdisable recovery cause bpduguarderrdisable recovery cause bpduguard

Description: Enable timer to recover from BPDU Guard error disable


Command Path:

# configure [['terminal', 't']](config)# errdisable recovery cause bpduguard


E Commandserrdisable recovery cause bpduguard

errdisable recovery cause ep-moveerrdisable recovery cause ep-move

Description: Enable timer to recover from End Point Move error disable


Command Path:

# configure [['terminal', 't']](config)# errdisable recovery cause ep-move


E Commandserrdisable recovery cause ep-move

errdisable recovery cause mcp-looperrdisable recovery cause mcp-loop

Description: Enable timer to recover from MCP Loop error disable


Command Path:

# configure [['terminal', 't']](config)# errdisable recovery cause mcp-loop


E Commandserrdisable recovery cause mcp-loop

errdisable recovery intervalerrdisable recovery interval <NUMBER>

Description: Configure Error Disable Recovery Interval

Syntax:

Timer-interval (sec). Number range from=30 to=65535<30-65535>


Command Path:

# configure [['terminal', 't']](config)# errdisable recovery interval <NUMBER>


E Commandserrdisable recovery interval

erspan-iderspan-id <id>

Description: Erspan Id

Syntax:

erspan Id. Number range from=1 to=1023id

Command Mode: destination tenant : Configure monitor remote destination

Command Path:

# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# destination tenant <tenant_name> application <application_name>epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M>(config-monitor-access-dest)# erspan-id <id>

erspan-id <id>


Syntax:

erspan Id. Number range from=1 to=1023id

Command Mode: destination : Configure monitor remote destination

Command Path:

# configure [['terminal', 't']](config)# monitor fabric session <session_name>(config-monitor-fabric)# destination tenant <tenant_name> application <application_name>epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M>(config-monitor-fabric-dest)# erspan-id <id>

erspan-id <arg>


Syntax:

erspan Id. Number range from=1 to=1023arg


Command Path:



E Commandserspan-id

(config)# monitor tenant <tenant_name> session <session_name>(config-monitor-tenant)# destination tenant <tenant_name> application <application_name>epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M>(config-monitor-tenant-dest)# erspan-id <>

erspan-id <arg>

Description: Configure ERSPAN ID

Syntax:

ERSPAN ID. Number range from=1 to=1023arg

Command Mode: destination destip : Configure monitor remote destination

Command Path:

# configure [['terminal', 't']](config)# monitor virtual session <WORD>(config-monitor-virtual)# destination destip <A.B.C.D>(config-monitor-virtual-remote-dest)# erspan-id <>


E Commandserspan-id

execexec

Description: Exec Mode

Command Mode: None


E Commandsexec

exitexit

Description: Exit from current mode


Command Path:

# exit


E Commandsexit

expirationexpiration <DATE>

Description: If expires enabled, Set expiration date of locally-authenticated user account.

Syntax:

UTC Date format (YYYY-MM-DDTHH:MM:SS.mmm[+-]hh:mm)DATE


Command Path:

# configure [['terminal', 't']](config)# username <WORD>(config-username)# expiration <DATE>


E Commandsexpiration

expiresexpires

Description: Enable expiry for locally-authenticated user account


Command Path:

# configure [['terminal', 't']](config)# username <WORD>(config-username)# expires


E Commandsexpires

exportexport to tenant <WORD> [as <WORD>]

Description: Export a contract to another tenant

Syntax:

Tenant to export the command toto

Tenant to export the command totenant

Tenant to export the command to (Max Size 63)WORD

(Optional) New name under which the contract will be known (MaxSize 64)

WORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# contract <WORD> [type <type>](config-tenant-contract)# export to tenant <WORD> [as <WORD>]

export map <WORD>

Description: VRF export

Syntax:

Route-map for inter VRF route leakmap


Command Mode: vrf : Configure VRF parameters

Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# export map <WORD>


E Commandsexport

external-l2external-l2 epg <WORD>

Description: L2 external EPG creation/configuration

Syntax:

L2 external EPG nameepg

L2 external EPG name (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l2 epg <WORD>


E Commandsexternal-l2

external-l3external-l3 epg <WORD>

Description: External L3 EPG to associate

Syntax:

Specify the external EPGepg

External L3 EPG nameWORD


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# external-l3 epg <WORD>


E Commandsexternal-l3

external-l3 epgexternal-l3 epg <WORD> [oob-mgmt] [l3out <l3out>]

Description: External L3 EPG configuration mode

Syntax:

External L3 EPG name (Max Size 49)WORD

(Optional) External L3 EPG for Out of bandoob-mgmt

(Optional) Configure external-l3 epg on an API configured L3Outl3out


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l3 epg <WORD> [oob-mgmt] [l3out <l3out>]


E Commandsexternal-l3 epg

F Commands

• fabric clear, page 228

• fabric show, page 229

• fex-interface-group, page 230

• fex-profile, page 231

• fex, page 232

• file, page 233

• filter, page 234

• filter tenant bd, page 236

• filter tenant vrf, page 237

• firewall-logging, page 238

• firewall, page 239

• firmware-version, page 240

• firmware, page 241

• firmware repository add, page 242

• firmware repository delete, page 243

• firmware upgrade controller-group, page 244

• firmware upgrade switch-group, page 245

• first-file, page 246

• first-name, page 247

• format, page 248


fabric clearfabric <nodes> clear <scope>

Description: clear switch information

Syntax:

node list<nodes>

switch command<scope>


Command Path:

# fabric <nodes> clear <scope>


F Commandsfabric clear

fabric showfabric <nodes> show <scope>

Description: show switch information

Syntax:

node list<nodes>

switch command<scope>


Command Path:

# fabric <nodes> show <scope>


F Commandsfabric show

fex-interface-groupfex-interface-group <WORD>

Description: Configure Fex Interface Group

Syntax:

Fex Interface Group Name (Max Size 64)WORD

Command Mode: fex-profile : Configure Fex Profile

Command Path:

# configure [['terminal', 't']](config)# fex-profile <WORD>(config-fex-profile)# fex-interface-group <WORD>


F Commandsfex-interface-group

fex-profilefex-profile <WORD>

Description: Configure Fex Profile

Syntax:

Fex Profile Name (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# fex-profile <WORD>


F Commandsfex-profile

fexfex associate <NUMBER> template <WORD>

Description: Configure Fex on the Interface

Syntax:

Associate the port to a FEXassociate

Fex Number. Number range from=101 to=164NUMBER

Associate a templatetemplate

Fex Template Name (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# leaf-interface-profile <WORD>(config-leaf-if-profile)# leaf-interface-group <WORD>(config-leaf-if-group)# fex associate <NUMBER> template <WORD>

fex associate <arg>

Description: Configure Fex on the Interface

Syntax:

Associate the port to a FEXassociate

Fex Number. Number range from=101 to=164arg


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# fex associate <>


F Commandsfex

filefile <FILENAME>

Description: Snapshot file name

Syntax:

Snapshot file nameFILENAME

Command Mode: snapshot download : Configuration snapshot download setup mode

Command Path:

# configure [['terminal', 't']](config)# snapshot download <WORD>(config-download)# file <FILENAME>

file <FILENAME>


Syntax:



Command Path:

# configure [['terminal', 't']](config)# snapshot import <WORD>(config-import)# file <FILENAME>

file <FILENAME>


Syntax:


Command Mode: snapshot upload : Configuration snapshot upload setup mode

Command Path:

# configure [['terminal', 't']](config)# snapshot upload <WORD>(config-upload)# file <FILENAME>


F Commandsfile

filterfilter <WORD>

Description: Set the LDAP filter to be used in a user search

Syntax:

filter used in user search (Max Size 63)<WORD>


Command Path:

# configure [['terminal', 't']](config)# ldap-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# filter <WORD>

filter tenant <tenant_name> application <application_name> epg <epg_name>

Description: EPG filter

Syntax:

tenanttenant




epgepg


Command Mode: source interface ethernet : Configure monitor for ethernet access interfaces

Command Path:

# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# source interface ethernet <ethernet> leaf <leaf Id>(config-monitor-access-source)# filter tenant <tenant_name> application <application_name>epg <epg_name>



Syntax:


F Commandsfilter

tenanttenant




epgepg


Command Mode: source interface port-channel : Configure monitor for port-channel interfaces

Command Path:

# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# source interface port-channel <port-channel list> leaf <leaf Id>[fex <fex Id>](config-monitor-access-source)# filter tenant <tenant_name> application <application_name>epg <epg_name>



Syntax:

tenanttenant




epgepg


Command Mode: source interface vpc : Configure monitor for VPC interfaces

Command Path:

# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# source interface vpc <vpc list> leaf <leaf Id1> <leaf Id2> [fex<fex Ids>](config-monitor-access-source)# filter tenant <tenant_name> application <application_name>epg <epg_name>


F Commandsfilter

filter tenant bdfilter tenant <tenant_name> bd <bd_name>

Description: BD filter

Syntax:

tenanttenant

tenant nametenant_name

BD namebd_name


Command Path:

# configure [['terminal', 't']](config)# monitor fabric session <session_name>(config-monitor-fabric)# source interface ethernet <ethernet> switch <switch Id>(config-monitor-fabric-source)# filter tenant <tenant_name> bd <bd_name>


F Commandsfilter tenant bd

filter tenant vrffilter tenant <tenant_name> vrf <vrf_name>

Description: VRF filter

Syntax:

tenanttenant

tenant nametenant_name

vrf namevrf_name


Command Path:

# configure [['terminal', 't']](config)# monitor fabric session <session_name>(config-monitor-fabric)# source interface ethernet <ethernet> switch <switch Id>(config-monitor-fabric-source)# filter tenant <tenant_name> vrf <vrf_name>


F Commandsfilter tenant vrf

firewall-loggingfirewall-logging server-group <WORD> [severity severity <severity-info>] [polling-interval <polling-interval>]

Description: Configure firewall-logging on AVS

Syntax:

Specify server group nameserver-group

Logging server-group name (Max Size 64)WORD

(Optional) Specify severity infoseverity <severity-info>

(Optional) Specify polling interval time in seconds. Number rangefrom=60 to=86400

polling-interval


Command Path:

# configure [['terminal', 't']](config)# vmware-domain <WORD>(config-vmware)# configure-avs(config-vmware-avs)# firewall-logging server-group <WORD> [severity severity <severity-info>][polling-interval <polling-interval>]


F Commandsfirewall-logging

firewallfirewall mode enabled|disabled|learning

Description: Configure firewall mode on AVS

Syntax:

firewall modemode

Enabled modeenabled

Disabled modedisabled

Learning modelearning


Command Path:

# configure [['terminal', 't']](config)# vmware-domain <WORD>(config-vmware)# configure-avs(config-vmware-avs)# firewall mode enabled|disabled|learning


F Commandsfirewall

firmware-versionfirmware-version <version>

Description: Set target firmware version

Syntax:


Command Mode: controller-group : Controller Upgrade Configuration Mode

Command Path:

# configure [['terminal', 't']](config)# firmware(config-firmware)# controller-group(config-firmware-controller)# firmware-version <version>

firmware-version <version>

Description: Set target firmware version

Syntax:



Command Path:

# configure [['terminal', 't']](config)# firmware(config-firmware)# switch-group <WORD>(config-firmware-switch)# firmware-version <version>


F Commandsfirmware-version

firmwarefirmware

Description: Firmware upgrade configuration Mode


Command Path:

# configure [['terminal', 't']](config)# firmware


F Commandsfirmware

firmware repository addfirmware repository add <WORD>

Description: Add firmware image to repository

Syntax:

Firmware image filename(absolute path)WORD


Command Path:

# firmware repository add <WORD>


F Commandsfirmware repository add

firmware repository deletefirmware repository delete <WORD>

Description: Remove firmware image from repository

Syntax:

Firmware image nameWORD


Command Path:

# firmware repository delete <WORD>


F Commandsfirmware repository delete

firmware upgrade controller-groupfirmware upgrade controller-group

Description: Trigger controller-group upgrade


Command Path:

# firmware upgrade controller-group


F Commandsfirmware upgrade controller-group

firmware upgrade switch-groupfirmware upgrade switch-group <WORD>

Description: Trigger switch-group upgrade

Syntax:

switch-group name (Max Size 64)WORD


Command Path:

# firmware upgrade switch-group <WORD>


F Commandsfirmware upgrade switch-group

first-filefirst-file <FILENAME>

Description: First snapshot file name

Syntax:

First snapshot file nameFILENAME

Command Mode: snapshot rollback : Configuration rollback setup mode

Command Path:

# configure [['terminal', 't']](config)# snapshot rollback <WORD>(config-rollback)# first-file <FILENAME>


F Commandsfirst-file

first-namefirst-name <WORD>

Description: Set the first name of the locally-authenticated user.

Syntax:

first name (Max Size 32)WORD


Command Path:

# configure [['terminal', 't']](config)# username <WORD>(config-username)# first-name <WORD>


F Commandsfirst-name

formatformat xml|short-txt|aml

Description: Configure the format of the message

Syntax:

Xmlxml

Short-txtshort-txt

Amlaml


Command Path:

# configure [['terminal', 't']](config)# callhome common(config-callhome)# destination-profile(config-callhome-destnprof)# destination <WORD>(config-callhome-destnprof-destn)# format xml|short-txt|aml

format xml|json

Description: Snapshot format: xml or json

Syntax:

XML formatxml

JSON formatjson

Command Mode: snapshot export : Configuration export setup mode

Command Path:

# configure [['terminal', 't']](config)# snapshot export <WORD>(config-export)# format xml|json


F Commandsformat

G Commands

• graceful-restart-helper, page 250

• graceful-restart, page 251

• group, page 252


graceful-restart-helpergraceful-restart-helper

Description: Configure BGP Policy Graceful Restart Helper

Command Mode: template bgp timers : Configure Router BGP Timer Policy Templates

Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template bgp timers <WORD> tenant <WORD>(config-bgp-timers)# graceful-restart-helper


G Commandsgraceful-restart-helper

graceful-restartgraceful-restart helper-disable

Description: Disable OSPF Policy Graceful Restart Helper

Syntax:

disable Restart helperhelper-disable


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf vrf-policy <WORD> tenant <WORD>(config-vrf-policy)# graceful-restart helper-disable

graceful-restart stalepath-time <NUMBER>

Description: Set BGP Policy Graceful Restart Timers

Syntax:

Maximum time that BGP keeps stale routes from the restarting BGPpeer

stalepath-time

Timer Value in Seconds. Number range from=1 to=3600<1-3600>


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template bgp timers <WORD> tenant <WORD>(config-bgp-timers)# graceful-restart stalepath-time <NUMBER>


G Commandsgraceful-restart

groupgroup <WORD>

Description: Specify server groups

Syntax:

Server group name (Max Size 127)<WORD>

Command Mode: aaa authentication login console : Configure console methods

Command Path:

# configure [['terminal', 't']](config)# aaa authentication login console(config-console)# group <WORD>

group <WORD>

Description: Specify server groups

Syntax:


Command Mode: aaa authentication login default : Configure default methods

Command Path:

# configure [['terminal', 't']](config)# aaa authentication login default(config-default)# group <WORD>

group <WORD>

Description: Set provider group for login domain

Syntax:


Command Mode: aaa authentication login domain : Configure domain methods

Command Path:

# configure [['terminal', 't']](config)# aaa authentication login domain <WORD>(config-domain)# group <WORD>


G Commandsgroup

H Commands

• hello-interval, page 254

• http, page 255

• https, page 256


hello-intervalhello-interval <NUMBER>

Description: Set interval between hello packets that OSPF sends on the interface

Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf interface-policy <WORD> tenant <WORD>(config-interface-policy)# hello-interval <NUMBER>


H Commandshello-interval

httphttp

Description: HTTP communication policy group

Command Mode: comm-policy : Configure any communication policy, ssh/telnet/shellinabox/http/https

Command Path:

# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# http


H Commandshttp

httpshttps

Description: HTTPS communication policy group


Command Path:

# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# https


H Commandshttps

I Commands

• inband-mgmt, page 261

• inband-mgmt epg, page 262

• inherit, page 263

• inherit bgp address-family, page 266

• inherit bgp dampening, page 267

• inherit eigrp, page 268

• inherit ipv4, page 269

• inherit ipv6, page 270

• instance, page 272

• interface, page 273

• interface ethernet, page 275

• interface inband-mgmt0, page 276

• interface mgmt0, page 277

• interface port-channel, page 278

• interface vlan, page 279

• interface vpc, page 280

• ip, page 281

• ip address-range, page 282

• ip address, page 284

• ip address tenant application, page 287

• ip address tenant external-l2, page 289

• ip address tenant external-l3, page 291

• ip bandwidth, page 293

• ip bfd, page 295


• ip dhcp relay address tenant application, page 297

• ip dhcp relay address tenant external-l2, page 298

• ip dhcp relay address tenant external-l3, page 299

• ip distribute-list eigrp, page 300

• ip dscp, page 301

• ip hello-interval, page 303

• ip hold-interval, page 305

• ip igmp snooping fast-leave, page 307

• ip igmp snooping last-member-query-interval, page 308

• ip igmp snooping optimise-multicast-flood, page 309

• ip igmp snooping policy, page 310

• ip igmp snooping querier, page 311

• ip igmp snooping query-interval, page 312

• ip igmp snooping query-max-response-time, page 313

• ip igmp snooping startup-query-count, page 314

• ip igmp snooping startup-query-interval, page 315

• ip next-hop-self, page 316

• ip ospf authentication-key, page 318

• ip ospf authentication, page 319

• ip ospf bfd, page 320

• ip ospf cost, page 321

• ip ospf dead-interval, page 322

• ip ospf hello-interval, page 323

• ip ospf inherit, page 324

• ip ospf mtu-ignore, page 325

• ip ospf network, page 326

• ip ospf passive-interface, page 327

• ip ospf prefix-suppression, page 328

• ip ospf priority, page 329

• ip ospf retransmit-interval, page 330

• ip ospf transmit-delay, page 331

• ip passive-interface, page 332

• ip prefix-list, page 334


I Commands

• ip prefix-list permit le, page 335

• ip router eigrp, page 336

• ip router ospf default, page 337

• ip shared address consumer, page 338

• ip shared address provider, page 339

• ip split-horizon, page 340

• ip summary-address eigrp, page 342

• ip throughput-delay, page 343

• ip ttl, page 345

• iprange, page 347

• ipv6, page 348

• ipv6 address-range, page 349

• ipv6 address, page 351

• ipv6 address tenant application, page 354

• ipv6 address tenant external-l2, page 356

• ipv6 address tenant external-l3, page 358

• ipv6 bandwidth, page 360

• ipv6 bfd, page 361

• ipv6 dhcp relay address tenant application, page 362

• ipv6 dhcp relay address tenant external-l2, page 363

• ipv6 dhcp relay address tenant external-l3, page 364

• ipv6 distribute-list eigrp, page 365

• ipv6 hello-interval, page 366

• ipv6 hold-interval, page 367

• ipv6 link-local, page 368

• ipv6 nd hop-limit, page 370

• ipv6 nd managed-config-flag, page 372

• ipv6 nd mtu, page 374

• ipv6 nd ns-interval, page 376

• ipv6 nd ns-retries, page 378

• ipv6 nd other-config-flag, page 380

• ipv6 nd policy, page 382

• ipv6 nd prefix, page 383


I Commands

• ipv6 nd ra-interval, page 385

• ipv6 nd ra-lifetime, page 387

• ipv6 nd reachable-time, page 389

• ipv6 nd retrans-timer, page 391

• ipv6 nd suppress-ra-mtu, page 393

• ipv6 nd suppress-ra, page 395

• ipv6 next-hop-self, page 397

• ipv6 ospf bfd, page 398

• ipv6 ospf cost, page 399

• ipv6 ospf dead-interval, page 400

• ipv6 ospf hello-interval, page 401

• ipv6 ospf inherit, page 402

• ipv6 ospf mtu-ignore, page 403

• ipv6 ospf network, page 404

• ipv6 ospf passive-interface, page 405

• ipv6 ospf prefix-suppression, page 406

• ipv6 ospf priority, page 407

• ipv6 ospf retransmit-interval, page 408

• ipv6 ospf transmit-delay, page 409

• ipv6 passive-interface, page 410

• ipv6 router eigrp, page 411

• ipv6 router ospf default, page 412

• ipv6 shared address consumer, page 413

• ipv6 shared address provider, page 414

• ipv6 split-horizon, page 415

• ipv6 throughput-delay, page 416

• isis, page 418

• isolation, page 419


I Commands

inband-mgmtinband-mgmt epg <WORD>

Description: Enter Inside In-band management mode to modify inband properties or create new inband

Syntax:

inband mgmt epg label, usage inband-mgmt epgepg

epg name for inband epg, it can be existing inband epg or new oneWORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# inband-mgmt epg <WORD>


I Commandsinband-mgmt

inband-mgmt epginband-mgmt epg <WORD>

Description: Associate node to a Inband EPG

Syntax:

Inband End Point Group Name (Max Size 64)WORD

Command Mode: interface inband-mgmt0 : Inband management interface

Command Path:

# configure [['terminal', 't']](config)# controller(config-controller)# interface inband-mgmt0(config-controller-if)# inband-mgmt epg <WORD>

inband-mgmt epg <WORD>

Description: Associate node to a Inband EPG

Syntax:

Inband End Point Group Name (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# switch(config-switch)# interface inband-mgmt0(config-switch-if)# inband-mgmt epg <WORD>


I Commandsinband-mgmt epg

inheritinherit bfd ip|ipv6 <WORD>

Description: Inherit BFD Policy

Syntax:

bfd

IPv4 Addressip

IPv6 Addressipv6

Inherit a BFD PolicyWORD

Command Mode: template leaf-policy-group : Configure Leaf Policy Group

Command Path:

# configure [['terminal', 't']](config)# template leaf-policy-group <WORD>(config-leaf-policy-group)# inherit bfd ip|ipv6 <WORD>

inherit route-profile <WORD>

Description: Inherit a policy template

Syntax:

Configure route-profile for bridge-domainroute-profile

Route profile nameWORD

Command Mode: match bridge-domain : Match subnets of a bridge-domain

Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match bridge-domain <>(config-leaf-vrf-route-map-match)# inherit route-profile <WORD>

inherit route tag <WORD>

Description: Inherit a policy template

Syntax:


I Commandsinherit

Policy template for routesroute

Route tag policy templatetag

Policy template name (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# inherit route tag <WORD>

inherit eigrp vrf-policy <WORD>

Description: Inherit EIGRP VRF Policy under this VRF

Syntax:

Inherit EIGRP VRF Policyeigrp

Inherit EIGRP VRF Policyvrf-policy

Policy nameWORD


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router eigrp default(config-eigrp)# vrf member tenant <WORD> vrf <WORD>(config-eigrp-vrf)# address-family ipv4|ipv6 unicast(config-address-family)# inherit eigrp vrf-policy <WORD>

inherit bgp timer <WORD>

Description: Inherit BGP Timer Template Policy under this VRF

Syntax:

Inherit BGP Timer Policybgp

Inherit BGP Timer Policytimer

BGP Template Policy Name (Max Size 64)WORD



I Commandsinherit

Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# inherit bgp timer <WORD>


I Commandsinherit

inherit bgp address-familyinherit bgp address-family <WORD>

Description: Inherit BGP Address Family Policy

Syntax:

BGP Address Family Policy Name (Max Size 64)WORD

Command Mode: address-family : Configure an address-family

Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# address-family ipv4|ipv6 unicast(config-leaf-bgp-vrf-af)# inherit bgp address-family <WORD>


I Commandsinherit bgp address-family

inherit bgp dampeninginherit bgp dampening <WORD>

Description: Inherit Route Profile with BGP Dampening Policy

Syntax:

Route Profile with BGP Dampening Policy Name (Max Size 64)WORD

Command Mode: address-family : Configure an address-family

Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# address-family ipv4|ipv6 unicast(config-leaf-bgp-vrf-af)# inherit bgp dampening <WORD>


I Commandsinherit bgp dampening

inherit eigrpinherit eigrp ip|ipv6 interface-policy <WORD>

Description: Inherit EIGRP interface template policy

Syntax:

Address Family IPv4ip


Associate the interface with an EIGRP interface policyinterface-policy

Policy nameWORD


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# inherit eigrp ip|ipv6 interface-policy <WORD>

inherit eigrp ip|ipv6 interface-policy <WORD>

Description: Inherit EIGRP interface template policy

Syntax:

Address Family IPv4ip


Associate the interface with an EIGRP interface policyinterface-policy

Policy nameWORD


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# inherit eigrp ip|ipv6 interface-policy <WORD>


I Commandsinherit eigrp

inherit ipv4inherit ipv4 ospf vrf-policy <WORD>

Description: Inherit OSPF Template Policy under this VRF

Syntax:

Inherit OSPF Policyospf

Inherit OSPF vrf-policyvrf-policy

OSPF Template Policy name (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# inherit ipv4 ospf vrf-policy <WORD>


I Commandsinherit ipv4

inherit ipv6inherit ipv6 nd <WORD>

Description: Inherit IPv6 Neighbor Discovery template policy

Syntax:

Associate the interface with an IPv6 Neighbor Discovery policynd

Policy nameWORD


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# inherit ipv6 nd <WORD>

inherit ipv6 nd <WORD>

Description: Inherit IPv6 Neighbor Discovery template policy

Syntax:

Associate the interface with an IPv6 Neighbor Discovery policynd

Policy nameWORD


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# inherit ipv6 nd <WORD>

inherit ipv6 ospf vrf-policy <WORD>


Syntax:

Inherit OSPF Policyospf

Inherit OSPF vrf-policyvrf-policy





Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# inherit ipv6 ospf vrf-policy <WORD>



instanceinstance <NUMBER> vlan <RANGE>

Description:Maps VLANs to an MST instance

Syntax:

MST instance ID. Number range from=1 to=4094<1-4094>

Virtual LANvlan

VLAN range. Ex.: 10-3000RANGE


Command Path:

# configure [['terminal', 't']](config)# spanning-tree mst configuration(config-stp)# region <WORD>(config-stp-region)# instance <NUMBER> vlan <RANGE>


I Commandsinstance

interfaceinterface bridge-domain <WORD>

Description: Configuration for interface bridge-domain

Syntax:

Name of the bridge-domainbridge-domain



Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>

interface ethernet

Description: Provide a Range of Interfaces

Syntax:

Configure Physical Interfaceethernet

Provide range of Interfacesarg


Command Path:

# configure [['terminal', 't']](config)# leaf-interface-profile <WORD>(config-leaf-if-profile)# leaf-interface-group <WORD>(config-leaf-if-group)# interface ethernet

interface ethernet

Description: Configure Ports on the Fex Interface Group

Syntax:




I Commandsinterface


Command Path:

# configure [['terminal', 't']](config)# fex-profile <WORD>(config-fex-profile)# fex-interface-group <WORD>(config-fex-if-group)# interface ethernet

interface vpc <WORD> [fex <fex>]

Description: Provide VPC Name

Syntax:

VPC Interfacevpc

VPC Name (Max Size 64)WORD

(Optional) Fex Id. Number range from=101 to=164fex

Command Mode: vpc context : Enter vpc context

Command Path:

# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>]


I Commandsinterface

interface ethernetinterface ethernet <ethernet> leaf <leaf-id>

Description: Configure Physical Ethernet Port as a Cluster Member Interface

Syntax:

List of ethernet itfs<ethernet>

Leaf ID that connects to cluster ethernet interface on (physical) device.leaf

Leaf ID that connects to cluster ethernet interface on (physical) device.<leaf-id>

Command Mode: member : Configure Cluster Interface Member

Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 cluster name <WORD> type <type> vlan-domain <domain-name> [service<service>] [function <function>](config-cluster)# cluster-interface <WORD> [vlan <NUMBER>](config-cluster-interface)# member device <WORD> device-interface <WORD>(config-member)# interface ethernet <ethernet> leaf <leaf-id>

interface ethernet <ifRange>

Description: Ethernet IEEE 802.3z

Syntax:

interface Range<ifRange>


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>


I Commandsinterface ethernet

interface inband-mgmt0interface inband-mgmt0

Description: Inband management interface

Command Mode: controller : Configure Controller Node

Command Path:

# configure [['terminal', 't']](config)# controller(config-controller)# interface inband-mgmt0

interface inband-mgmt0

Description: Inband management interface

Command Mode: switch : Configure Leaf Node

Command Path:

# configure [['terminal', 't']](config)# switch(config-switch)# interface inband-mgmt0


I Commandsinterface inband-mgmt0

interface mgmt0interface mgmt0

Description: Out of band management interface

Command Mode: controller : Configure Controller Node

Command Path:

# configure [['terminal', 't']](config)# controller(config-controller)# interface mgmt0

interface mgmt0

Description: Out of band management interface

Command Mode: switch : Configure Leaf Node

Command Path:

# configure [['terminal', 't']](config)# switch(config-switch)# interface mgmt0


I Commandsinterface mgmt0

interface port-channelinterface port-channel <port-channel-name> leaf <NUMBER> [fex <fex-id>]

Description: Configure Port Channel as a Cluster Member Interface

Syntax:

Name of the port-channel<port-channel-name>

Leaf Id for the port-channelleaf

Leaf Id for the port channel.. Number range from=0to=9223372036854775807

NUMBER

(Optional) Fex ID that connects to cluster interface interface on(physical) device.

<fex-id>


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 cluster name <WORD> type <type> vlan-domain <domain-name> [service<service>] [function <function>](config-cluster)# cluster-interface <WORD> [vlan <NUMBER>](config-cluster-interface)# member device <WORD> device-interface <WORD>(config-member)# interface port-channel <port-channel-name> leaf <NUMBER> [fex <fex-id>]

interface port-channel <WORD> [fex <fex>]

Description: Port Channel interface

Syntax:

Port-Channel Name (Max Size 64)WORD



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>]


I Commandsinterface port-channel

interface vlaninterface vlan <1-4094>

Description: Vlan interface

Syntax:

Vlan interface number<1-4094>


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>


I Commandsinterface vlan

interface vpcinterface vpc <vpc-name> leaf <NUMBER> <NUMBER> [fex fex <Ids>]

Description: Configure monitor for VPC interfaces

Syntax:

VPC port-channel group name<vpc-name>

leafleaf

First leaf member of the Pair. Number range from=0to=9223372036854775807

NUMBER

Second leaf member of the Pair. Number range from=0to=9223372036854775807

NUMBER

(Optional) paired fex Idsfex <Ids>


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 cluster name <WORD> type <type> vlan-domain <domain-name> [service<service>] [function <function>](config-cluster)# cluster-interface <WORD> [vlan <NUMBER>](config-cluster-interface)# member device <WORD> device-interface <WORD>(config-member)# interface vpc <vpc-name> leaf <NUMBER> <NUMBER> [fex fex <Ids>]


I Commandsinterface vpc

ipip route <A.B.C.D/LEN> <ipAddress|null> <ZeroorPref> <BfdorPref>

Description: Configure IP features

Syntax:

Route informationroute

IP prefix and network mask length in format x.x.x.x/mA.B.C.D/LEN

ipAddress|null

<ZeroorPref>

<BfdorPref>


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# ip route <A.B.C.D/LEN> <ipAddress|null> <ZeroorPref> <BfdorPref>


I Commandsip

ip address-rangeip address-range <A.B.C.D/LEN> gateway <A.B.C.D>

Description: Configure IP and gateway features

Syntax:

IP Address and network mask length in format x.x.x.x/mA.B.C.D/LEN

Configure gateway address on interfacegateway

Network mask length in format x.x.x.xA.B.C.D

Command Mode: interface mgmt0 : Out of band management interface

Command Path:

# configure [['terminal', 't']](config)# controller(config-controller)# interface mgmt0(config-controller-if)# ip address-range <A.B.C.D/LEN> gateway <A.B.C.D>

ip address-range <A.B.C.D/LEN> gateway <A.B.C.D>


Syntax:

IP address and network mask length in format x.x.x.x/mA.B.C.D/LEN




Command Path:

# configure [['terminal', 't']](config)# controller(config-controller)# interface inband-mgmt0(config-controller-if)# ip address-range <A.B.C.D/LEN> gateway <A.B.C.D>

ip address-range <A.B.C.D/LEN> gateway <A.B.C.D>


Syntax:

IP Address and network mask length in format x.x.x.x/mA.B.C.D/LEN


I Commandsip address-range




Command Path:

# configure [['terminal', 't']](config)# switch(config-switch)# interface mgmt0(config-switch-if)# ip address-range <A.B.C.D/LEN> gateway <A.B.C.D>

ip address-range <A.B.C.D> gateway <A.B.C.D>


Syntax:

IP address and network mask length in format x.x.x.x/mA.B.C.D




Command Path:

# configure [['terminal', 't']](config)# switch(config-switch)# interface inband-mgmt0(config-switch-if)# ip address-range <A.B.C.D> gateway <A.B.C.D>


I Commandsip address-range

ip addressip address <A.B.C.D/LEN> [scope <scope>] [secondary] [multi-site] [snooping-querier]

Description: Define an IPv4 subnet to be exported by the BD

Syntax:


(Optional) Scope of the address among ['public', 'private']scope

(Optional) Set the address as secondary addresssecondary

(Optional) Set the address as multi-site addressmulti-site

(Optional) Tell the address to be used by IGMP Snooping querierfunctionality if enabled

snooping-querier


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip address <A.B.C.D/LEN> [scope <scope>] [secondary] [multi-site][snooping-querier]

ip address <A.B.C.D/LEN> [secondary]

Description: Configure IP address on interface

Syntax:


(Optional) Configure additional IP addresses on interfacesecondary


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip address <A.B.C.D/LEN> [secondary]

ip address <A.B.C.D/LEN> [secondary]

Description: Configure IP address on interface


I Commandsip address

Syntax:


(Optional) Configure IP Address as Secondary IPsecondary


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip address <A.B.C.D/LEN> [secondary]

ip address <A.B.C.D/LEN> gateway <A.B.C.D>


Syntax:





Command Path:

# configure [['terminal', 't']](config)# controller(config-controller)# interface mgmt0(config-controller-if)# ip address <A.B.C.D/LEN> gateway <A.B.C.D>



Syntax:







Command Path:

# configure [['terminal', 't']](config)# controller(config-controller)# interface inband-mgmt0(config-controller-if)# ip address <A.B.C.D/LEN> gateway <A.B.C.D>



Syntax:





Command Path:

# configure [['terminal', 't']](config)# switch(config-switch)# interface mgmt0(config-switch-if)# ip address <A.B.C.D/LEN> gateway <A.B.C.D>



Syntax:





Command Path:

# configure [['terminal', 't']](config)# switch(config-switch)# interface inband-mgmt0(config-switch-if)# ip address <A.B.C.D/LEN> gateway <A.B.C.D>



ip address tenant applicationip address <A.B.C.D> tenant <WORD> application <WORD> epg <WORD>

Description: Add a new server relay address under an AEPg

Syntax:


Tenant hosting the DHCP servertenant

Tenant hosting the EPG (Max Size 63)WORD

Application hosting the EPG (Max Size 64)WORD

AEPg behind which the DHCP server sitsepg

AEPg behind which the DHCP server sits (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# template dhcp relay policy <WORD>(config-template-dhcp-relay)# ip address <A.B.C.D> tenant <WORD> application <WORD> epg<WORD>

ip address <A.B.C.D> tenant <WORD> application <WORD> epg <WORD>


Syntax:









I Commandsip address tenant application

Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template dhcp relay policy <WORD>(config-tenant-template-dhcp-relay)# ip address <A.B.C.D> tenant <WORD> application <WORD>epg <WORD>


I Commandsip address tenant application

ip address tenant external-l2ip address <A.B.C.D> tenant <WORD> external-l2 epg <WORD>

Description: Add a new server relay address under a L2 External EPG

Syntax:




epg keywordepg

l2 external EPG behind which the DHCP server sits (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# template dhcp relay policy <WORD>(config-template-dhcp-relay)# ip address <A.B.C.D> tenant <WORD> external-l2 epg <WORD>

ip address <A.B.C.D> tenant <WORD> external-l2 epg <WORD>


Syntax:




epg keywordepg



Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template dhcp relay policy <WORD>(config-tenant-template-dhcp-relay)# ip address <A.B.C.D> tenant <WORD> external-l2 epg


I Commandsip address tenant external-l2

<WORD>



ip address tenant external-l3ip address <A.B.C.D> tenant <WORD> external-l3 epg <WORD>


Syntax:




EPG keywordepg



Command Path:

# configure [['terminal', 't']](config)# template dhcp relay policy <WORD>(config-template-dhcp-relay)# ip address <A.B.C.D> tenant <WORD> external-l3 epg <WORD>

ip address <A.B.C.D> tenant <WORD> external-l3 epg <WORD>


Syntax:




EPG keywordepg



Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template dhcp relay policy <WORD>(config-tenant-template-dhcp-relay)# ip address <A.B.C.D> tenant <WORD> external-l3 epg



<WORD>



ip bandwidthip bandwidth eigrp default <NUMBER>

Description: Set EIGRP bandwidth

Syntax:

EIGRPeigrp

EIGRP default instancedefault

bandwidth in kbps. Number range from=0 to=2560000000<0-2560000000>

Command Mode: template eigrp interface-policy : Configure EIGRP Interface policy templates

Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template eigrp interface-policy <WORD> tenant <WORD>(config-template-eigrp-if-pol)# ip bandwidth eigrp default <NUMBER>

ip bandwidth eigrp default <NUMBER>


Syntax:

EIGRPeigrp




Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip bandwidth eigrp default <NUMBER>

ip bandwidth eigrp default <NUMBER>


Syntax:

EIGRPeigrp


I Commandsip bandwidth




Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip bandwidth eigrp default <NUMBER>


I Commandsip bandwidth

ip bfdip bfd enable


Syntax:

Enable BFDenable


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template eigrp interface-policy <WORD> tenant <WORD>(config-template-eigrp-if-pol)# ip bfd enable

ip bfd eigrp enable

Description: Enable EIGRP Bidirectional Forwarding Detection

Syntax:

EIGRPeigrp

Enable BFDenable


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip bfd eigrp enable

ip bfd eigrp enable


Syntax:

EIGRPeigrp

Enable BFDenable



I Commandsip bfd

Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip bfd eigrp enable


I Commandsip bfd

ip dhcp relay address tenant applicationip dhcp relay address <A.B.C.D> tenant <WORD> application <WORD> epg <WORD>


Syntax:








Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip dhcp relay address <A.B.C.D> tenant <WORD> application <WORD>epg <WORD>


I Commandsip dhcp relay address tenant application

ip dhcp relay address tenant external-l2ip dhcp relay address <A.B.C.D> tenant <WORD> external-l2 epg <WORD>


Syntax:




epg keywordepg



Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip dhcp relay address <A.B.C.D> tenant <WORD> external-l2 epg<WORD>


I Commandsip dhcp relay address tenant external-l2

ip dhcp relay address tenant external-l3ip dhcp relay address <A.B.C.D> tenant <WORD> external-l3 epg <WORD>


Syntax:




EPG keywordepg



Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip dhcp relay address <A.B.C.D> tenant <WORD> external-l3 epg<WORD>


I Commandsip dhcp relay address tenant external-l3

ip distribute-list eigrpip distribute-list eigrp default route-map <WORD> out

Description: Configure distribute-list EIGRP route-map

Syntax:


route maproute-map

Route-map name (Max Size 64)WORD

outout


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip distribute-list eigrp default route-map <WORD> out

ip distribute-list eigrp default route-map <WORD> out

Description: Configure distribute-list EIGRP Policies

Syntax:


route maproute-map


outout


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip distribute-list eigrp default route-map <WORD> out


I Commandsip distribute-list eigrp

ip dscpip dscp <dscp>

Description: dscp

Syntax:

DSCP code or valuedscp


Command Path:

# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# destination tenant <tenant_name> application <application_name>epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M>(config-monitor-access-dest)# ip dscp <dscp>

ip dscp <dscp>

Description: dscp

Syntax:



Command Path:

# configure [['terminal', 't']](config)# monitor fabric session <session_name>(config-monitor-fabric)# destination tenant <tenant_name> application <application_name>epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M>(config-monitor-fabric-dest)# ip dscp <dscp>

ip dscp <dscp>

Description: dscp

Syntax:



Command Path:



I Commandsip dscp

(config)# monitor tenant <tenant_name> session <session_name>(config-monitor-tenant)# destination tenant <tenant_name> application <application_name>epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M>(config-monitor-tenant-dest)# ip dscp <dscp>

ip dscp <dscp>

Description: Configure DSCP

Syntax:

<dscp><dscp>


Command Path:

# configure [['terminal', 't']](config)# monitor virtual session <WORD>(config-monitor-virtual)# destination destip <A.B.C.D>(config-monitor-virtual-remote-dest)# ip dscp <dscp>


I Commandsip dscp

ip hello-intervalip hello-interval eigrp default <NUMBER>

Description: Set EIGRP Hello interval time

Syntax:

EIGRPeigrp


Hello interval time in seconds. Number range from=1 to=65535<1-65535>


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template eigrp interface-policy <WORD> tenant <WORD>(config-template-eigrp-if-pol)# ip hello-interval eigrp default <NUMBER>

ip hello-interval eigrp default <NUMBER>


Syntax:

EIGRPeigrp




Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip hello-interval eigrp default <NUMBER>

ip hello-interval eigrp default <NUMBER>


Syntax:

EIGRPeigrp


I Commandsip hello-interval




Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip hello-interval eigrp default <NUMBER>


I Commandsip hello-interval

ip hold-intervalip hold-interval eigrp default <NUMBER>

Description: Set EIGRP Hold interval time

Syntax:

EIGRPeigrp


Hold interval time in seconds. Number range from=1 to=65535<1-65535>


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template eigrp interface-policy <WORD> tenant <WORD>(config-template-eigrp-if-pol)# ip hold-interval eigrp default <NUMBER>

ip hold-interval eigrp default <NUMBER>


Syntax:

EIGRPeigrp




Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip hold-interval eigrp default <NUMBER>

ip hold-interval eigrp default <NUMBER>


Syntax:

EIGRPeigrp


I Commandsip hold-interval




Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip hold-interval eigrp default <NUMBER>


I Commandsip hold-interval

ip igmp snooping fast-leaveip igmp snooping fast-leave

Description: Enable IP IGMP Snooping fast leave processing


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip igmp snooping fast-leave

ip igmp snooping fast-leave

Description: Enable IP IGMP Snooping fast leave processing


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip igmp snooping policy <WORD>(config-tenant-template-ip-igmp-snooping)# ip igmp snooping fast-leave


I Commandsip igmp snooping fast-leave

ip igmp snooping last-member-query-intervalip igmp snooping last-member-query-interval <NUMBER>

Description: Change the IP IGMP snooping last member query interval param

Syntax:

Last Memeber Query Interval Value. Number range from=1 to=25<1-25>


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip igmp snooping last-member-query-interval <NUMBER>

ip igmp snooping last-member-query-interval <NUMBER>

Description: Change the IP IGMP snooping last member query interval param

Syntax:

Last Memeber Query Interval Value. Number range from=1 to=25<1-25>


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip igmp snooping policy <WORD>(config-tenant-template-ip-igmp-snooping)# ip igmp snooping last-member-query-interval<NUMBER>


I Commandsip igmp snooping last-member-query-interval

ip igmp snooping optimise-multicast-floodip igmp snooping optimise-multicast-flood

Description: Enable IP IGMP Snooping multicast flood optimization


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip igmp snooping optimise-multicast-flood

ip igmp snooping optimise-multicast-flood

Description: Enable IP IGMP Snooping multicast flood optimization


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip igmp snooping policy <WORD>(config-tenant-template-ip-igmp-snooping)# ip igmp snooping optimise-multicast-flood


I Commandsip igmp snooping optimise-multicast-flood

ip igmp snooping policyip igmp snooping policy <WORD>

Description: Associate the BD with an IGMP snooping policy

Syntax:

Name of the IGMP snooping policy to attach (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip igmp snooping policy <WORD>


I Commandsip igmp snooping policy

ip igmp snooping querierip igmp snooping querier

Description: Enable IP IGMP Snooping querier processing


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip igmp snooping querier

ip igmp snooping querier

Description: Enable IP IGMP Snooping querier processing


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip igmp snooping policy <WORD>(config-tenant-template-ip-igmp-snooping)# ip igmp snooping querier


I Commandsip igmp snooping querier

ip igmp snooping query-intervalip igmp snooping query-interval <NUMBER>

Description: Change the IP IGMP snooping query interval param

Syntax:

Query Interval Value. Number range from=1 to=18000<1-18000>


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip igmp snooping query-interval <NUMBER>

ip igmp snooping query-interval <NUMBER>

Description: Change the IP IGMP snooping query interval param

Syntax:

Query Interval Value. Number range from=1 to=18000<1-18000>


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip igmp snooping policy <WORD>(config-tenant-template-ip-igmp-snooping)# ip igmp snooping query-interval <NUMBER>


I Commandsip igmp snooping query-interval

ip igmp snooping query-max-response-timeip igmp snooping query-max-response-time <NUMBER>

Description: Change the IP IGMP snooping max query response time

Syntax:

Query Max Response Time. Number range from=1 to=25<1-25>


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip igmp snooping query-max-response-time <NUMBER>

ip igmp snooping query-max-response-time <NUMBER>

Description: Change the IP IGMP snooping max query response time

Syntax:

Query Max Response Time. Number range from=1 to=25<1-25>


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip igmp snooping policy <WORD>(config-tenant-template-ip-igmp-snooping)# ip igmp snooping query-max-response-time <NUMBER>


I Commandsip igmp snooping query-max-response-time

ip igmp snooping startup-query-countip igmp snooping startup-query-count <NUMBER>

Description: Change the IP IGMP snooping number of initial queries to send

Syntax:

Start Query Count. Number range from=1 to=10<1-10>


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip igmp snooping startup-query-count <NUMBER>

ip igmp snooping startup-query-count <NUMBER>

Description: Change the IP IGMP snooping number of initial queries to send

Syntax:

Start Query Count. Number range from=1 to=10<1-10>


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip igmp snooping policy <WORD>(config-tenant-template-ip-igmp-snooping)# ip igmp snooping startup-query-count <NUMBER>


I Commandsip igmp snooping startup-query-count

ip igmp snooping startup-query-intervalip igmp snooping startup-query-interval <NUMBER>

Description: Change the IP IGMP snooping time for sending initial queries

Syntax:

Start Query Interval Value. Number range from=1 to=18000<1-18000>


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip igmp snooping startup-query-interval <NUMBER>

ip igmp snooping startup-query-interval <NUMBER>

Description: Change the IP IGMP snooping time for sending initial queries

Syntax:

Start Query Interval Value. Number range from=1 to=18000<1-18000>


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip igmp snooping policy <WORD>(config-tenant-template-ip-igmp-snooping)# ip igmp snooping startup-query-interval <NUMBER>


I Commandsip igmp snooping startup-query-interval

ip next-hop-selfip next-hop-self eigrp default

Description: Set the next-hop-self flag

Syntax:

EIGRPeigrp



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template eigrp interface-policy <WORD> tenant <WORD>(config-template-eigrp-if-pol)# ip next-hop-self eigrp default

ip next-hop-self eigrp default

Description: Set EIGRP next-hop-self flag

Syntax:

EIGRPeigrp



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip next-hop-self eigrp default

ip next-hop-self eigrp default


Syntax:

EIGRPeigrp



I Commandsip next-hop-self


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip next-hop-self eigrp default


I Commandsip next-hop-self

ip ospf authentication-keyip ospf authentication-key <WORD>

Description: Set OSPF authentication key

Syntax:

OSPF authentication keyWORD


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip ospf authentication-key <WORD>

ip ospf authentication-key <WORD>

Description: Set OSPF authentication key

Syntax:

OSPF authentication keyWORD


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip ospf authentication-key <WORD>


I Commandsip ospf authentication-key

ip ospf authenticationip ospf authentication md5|none|simple

Description: Set the OSPF authentication type

Syntax:

MD5 authenticationmd5

No authenticationnone

Simple authenticationsimple


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip ospf authentication md5|none|simple

ip ospf authentication md5|none|simple

Description: Set the OSPF authentication type

Syntax:

MD5 authenticationmd5

No authenticationnone

Simple authenticationsimple


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip ospf authentication md5|none|simple


I Commandsip ospf authentication

ip ospf bfdip ospf bfd enable


Syntax:

Enable BFDenable


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip ospf bfd enable

ip ospf bfd enable


Syntax:

Enable BFDenable


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip ospf bfd enable


I Commandsip ospf bfd

ip ospf costip ospf cost <NUMBER>


Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip ospf cost <NUMBER>

ip ospf cost <NUMBER>


Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip ospf cost <NUMBER>


I Commandsip ospf cost

ip ospf dead-intervalip ospf dead-interval <NUMBER>


Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip ospf dead-interval <NUMBER>

ip ospf dead-interval <NUMBER>


Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip ospf dead-interval <NUMBER>


I Commandsip ospf dead-interval

ip ospf hello-intervalip ospf hello-interval <NUMBER>


Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip ospf hello-interval <NUMBER>

ip ospf hello-interval <NUMBER>


Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip ospf hello-interval <NUMBER>


I Commandsip ospf hello-interval

ip ospf inheritip ospf inherit interface-policy <WORD> tenant <WORD>


Syntax:

Inherit OSPF interface-policyinterface-policy


tenant nametenant

Tenant name (Max Size 63)WORD


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip ospf inherit interface-policy <WORD> tenant <WORD>

ip ospf inherit interface-policy <WORD> tenant <WORD>


Syntax:



tenant nametenant



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip ospf inherit interface-policy <WORD> tenant <WORD>


I Commandsip ospf inherit

ip ospf mtu-ignoreip ospf mtu-ignore



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip ospf mtu-ignore

ip ospf mtu-ignore



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip ospf mtu-ignore


I Commandsip ospf mtu-ignore

ip ospf networkip ospf network bcast|p2p|unspecified

Description: Set OSPF interface policy network type

Syntax:

The OSPF interface policy network type. OSPF supports point-to-pointand broadcast.

bcast


p2p


unspecified


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip ospf network bcast|p2p|unspecified

ip ospf network bcast|p2p|unspecified


Syntax:


bcast


p2p


unspecified


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip ospf network bcast|p2p|unspecified


I Commandsip ospf network

ip ospf passive-interfaceip ospf passive-interface



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip ospf passive-interface

ip ospf passive-interface



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip ospf passive-interface


I Commandsip ospf passive-interface

ip ospf prefix-suppressionip ospf prefix-suppression disable|enable|inherit

Description: Set prefix suppression

Syntax:

The OSPF interface prefix suppression.disable

The OSPF interface prefix suppression.enable

The OSPF interface prefix suppression.inherit


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip ospf prefix-suppression disable|enable|inherit

ip ospf prefix-suppression disable|enable|inherit


Syntax:





Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip ospf prefix-suppression disable|enable|inherit


I Commandsip ospf prefix-suppression

ip ospf priorityip ospf priority <NUMBER>

Description: Set OSPF interface priority used to determine the designated router (DR) on a specific network

Syntax:

OSPF priority. Number range from=0 to=255<0-255>


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip ospf priority <NUMBER>

ip ospf priority <NUMBER>


Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip ospf priority <NUMBER>


I Commandsip ospf priority

ip ospf retransmit-intervalip ospf retransmit-interval <NUMBER>

Description: Set OSPF Policy Graceful Restart Timers

Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip ospf retransmit-interval <NUMBER>

ip ospf retransmit-interval <NUMBER>


Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip ospf retransmit-interval <NUMBER>


I Commandsip ospf retransmit-interval

ip ospf transmit-delayip ospf transmit-delay <NUMBER>

Description: Set the delay time needed to send an LSA update packet.

Syntax:

Delay in seconds. Number range from=1 to=450<1-450>


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip ospf transmit-delay <NUMBER>

ip ospf transmit-delay <NUMBER>


Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip ospf transmit-delay <NUMBER>


I Commandsip ospf transmit-delay

ip passive-interfaceip passive-interface eigrp default

Description: Set the passive-interface flag

Syntax:

EIGRPeigrp



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template eigrp interface-policy <WORD> tenant <WORD>(config-template-eigrp-if-pol)# ip passive-interface eigrp default

ip passive-interface eigrp default

Description: Set EIGRP passive-interface flag

Syntax:

EIGRPeigrp



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip passive-interface eigrp default

ip passive-interface eigrp default


Syntax:

EIGRPeigrp



I Commandsip passive-interface


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip passive-interface eigrp default


I Commandsip passive-interface

ip prefix-listip prefix-list <WORD> permit <A.B.C.D/LEN | A:B::C:D/LEN>

Description: Build a prefix-list

Syntax:

Name of prefix-list (Max Size 64)WORD

Specify routes to forwardpermit

IP prefix network/length, e.g., 35.0.0.0/8 or 2001::/64A.B.C.D/LEN | A:B::C:D/LEN

Command Mode: route-map : Create route-map or enter route-map command mode

Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# ip prefix-list <WORD> permit <A.B.C.D/LEN | A:B::C:D/LEN>


I Commandsip prefix-list

ip prefix-list permit leip prefix-list <WORD> permit <A.B.C.D/LEN | A:B::C:D/LEN> le <32>

Description:Maximum prefix length to be matched

Syntax:


Specify routes to forwardpermit

IP prefix network/length, e.g., 35.0.0.0/8 or 2001::/64A.B.C.D/LEN | A:B::C:D/LEN

Maximum prefix length32


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# ip prefix-list <WORD> permit <A.B.C.D/LEN | A:B::C:D/LEN> le<32>


I Commandsip prefix-list permit le

ip router eigrpip router eigrp default

Description: Configure Router EIGRP Policies

Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip router eigrp default

ip router eigrp default

Description: Configure EIGRP default interface

Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip router eigrp default


I Commandsip router eigrp

ip router ospf defaultip router ospf default area <A.B.C.D|NUMBER>

Description: Process tag

Syntax:

Area associated with interfacearea

OSPF area IdA.B.C.D|NUMBER


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip router ospf default area <A.B.C.D|NUMBER>

ip router ospf default area <A.B.C.D|NUMBER>


Syntax:




Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip router ospf default area <A.B.C.D|NUMBER>


I Commandsip router ospf default

ip shared address consumerip shared address <A.B.C.D/LEN> consumer application any epg any

Description: Shared consumed service

Syntax:

IPv4 subnetaddress


application keywordapplication

any applicationany

epg keywordepg

any EPGany


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip shared address <A.B.C.D/LEN> consumer application any epg any


I Commandsip shared address consumer

ip shared address providerip shared address <A.B.C.D/LEN> provider application <WORD> epg <WORD> [scope <scope>]

Description: Shared provider service

Syntax:

IPv4 subnetaddress




epg keywordepg

Application EPG (Max Size 64)WORD

(Optional) Scope of the address among ['public']scope


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip shared address <A.B.C.D/LEN> provider application <WORD> epg<WORD> [scope <scope>]


I Commandsip shared address provider

ip split-horizonip split-horizon eigrp default

Description: Set the split-horizon flag

Syntax:

EIGRPeigrp



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template eigrp interface-policy <WORD> tenant <WORD>(config-template-eigrp-if-pol)# ip split-horizon eigrp default

ip split-horizon eigrp default

Description: Set EIGRP split-horizon flag

Syntax:

EIGRPeigrp



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip split-horizon eigrp default

ip split-horizon eigrp default


Syntax:

EIGRPeigrp



I Commandsip split-horizon


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip split-horizon eigrp default


I Commandsip split-horizon

ip summary-address eigrpip summary-address eigrp default <IP-PREFIX/LEN>

Description: Configure route summarization for EIGRP

Syntax:


Summary IPV4/IPV6 address (e.g. 10.0.0.0/8 or 2001:0DB8:0:1::/64)IP-PREFIX/LEN


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip summary-address eigrp default <IP-PREFIX/LEN>

ip summary-address eigrp default <IP-PREFIX/LEN>

Description: Configure route summarization for EIGRP

Syntax:


Summary IPV4/IPV6 address (e.g. 10.0.0.0/8 or 2001:0DB8:0:1::/64)IP-PREFIX/LEN


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip summary-address eigrp default <IP-PREFIX/LEN>


I Commandsip summary-address eigrp

ip throughput-delayip throughput-delay eigrp default <NUMBER> tens-of-micro|pico

Description: Set EIGRP throughut delay

Syntax:

EIGRPeigrp


Throughtput delay. Number range from=0 to=16777215<0-16777215>

Unit in 10-microsecondstens-of-micro

Unit in picosecondspico


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template eigrp interface-policy <WORD> tenant <WORD>(config-template-eigrp-if-pol)# ip throughput-delay eigrp default <NUMBER> tens-of-micro|pico

ip throughput-delay eigrp default <NUMBER> tens-of-micro|pico


Syntax:

EIGRPeigrp






Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>


I Commandsip throughput-delay

(config-leaf-if)# ip throughput-delay eigrp default <NUMBER> tens-of-micro|pico

ip throughput-delay eigrp default <NUMBER> tens-of-micro|pico


Syntax:

EIGRPeigrp






Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip throughput-delay eigrp default <NUMBER> tens-of-micro|pico


I Commandsip throughput-delay

ip ttlip ttl <ttl>

Description: TTL

Syntax:

ttl value. Number range from=1 to=255ttl


Command Path:

# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# destination tenant <tenant_name> application <application_name>epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M>(config-monitor-access-dest)# ip ttl <ttl>

ip ttl <ttl>

Description: TTL

Syntax:

ttl value. Number range from=1 to=255ttl


Command Path:

# configure [['terminal', 't']](config)# monitor fabric session <session_name>(config-monitor-fabric)# destination tenant <tenant_name> application <application_name>epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M>(config-monitor-fabric-dest)# ip ttl <ttl>

ip ttl <arg>

Description: TTL

Syntax:

ttl value. Number range from=1 to=255arg


Command Path:



I Commandsip ttl

(config)# monitor tenant <tenant_name> session <session_name>(config-monitor-tenant)# destination tenant <tenant_name> application <application_name>epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M>(config-monitor-tenant-dest)# ip ttl <>

ip ttl <arg>

Description: Configure TTL

Syntax:

TTL value. Number range from=1 to=255arg


Command Path:

# configure [['terminal', 't']](config)# monitor virtual session <WORD>(config-monitor-virtual)# destination destip <A.B.C.D>(config-monitor-virtual-remote-dest)# ip ttl <>


I Commandsip ttl

iprangeiprange <startip> <endip>

Description: Add ip pool

Syntax:

startipstartip

endipendip


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# microsoft static-ip-pool <name> gateway <gwAddress>(config-tenant-app-epg-ms-ip-pool)# iprange <startip> <endip>


I Commandsiprange

ipv6ipv6 route <A:B::C:D/LEN> <ipAddress|null> <ZeroorPref> <BfdorPref>

Description: Configure IPv6 features

Syntax:

Configure IPv6 unicast static routeroute

IPv6 prefix format: xxxx:xxxx/ml, xxxx:xxxx::/ml, xxxx::xx/128A:B::C:D/LEN

ipAddress|null

<ZeroorPref>

<BfdorPref>


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# ipv6 route <A:B::C:D/LEN> <ipAddress|null> <ZeroorPref> <BfdorPref>


I Commandsipv6

ipv6 address-rangeipv6 address-range <A:B:C::X/LEN> gateway <A:B:C:X>

Description: Configure IPv6 Address Range

Syntax:

IPv6 address and network mask lengthA:B:C::X/LEN


Gateway IPv6 addressA:B:C:X


Command Path:

# configure [['terminal', 't']](config)# controller(config-controller)# interface mgmt0(config-controller-if)# ipv6 address-range <A:B:C::X/LEN> gateway <A:B:C:X>

ipv6 address-range <A:B:C::X/LEN> gateway <A:B:C:X>


Syntax:





Command Path:

# configure [['terminal', 't']](config)# controller(config-controller)# interface inband-mgmt0(config-controller-if)# ipv6 address-range <A:B:C::X/LEN> gateway <A:B:C:X>



Syntax:



I Commandsipv6 address-range




Command Path:

# configure [['terminal', 't']](config)# switch(config-switch)# interface mgmt0(config-switch-if)# ipv6 address-range <A:B:C::X/LEN> gateway <A:B:C:X>



Syntax:





Command Path:

# configure [['terminal', 't']](config)# switch(config-switch)# interface inband-mgmt0(config-switch-if)# ipv6 address-range <A:B:C::X/LEN> gateway <A:B:C:X>


I Commandsipv6 address-range

ipv6 addressipv6 address <A:B::C:D/LEN> [scope <scope>] [preferred] [suppress-nd] [eui64]

Description: Define an IPv6 subnet to be exported by the BD

Syntax:


(Optional) Scope of the address among ['public', 'private']scope

(Optional) Set the address as preferred addresspreferred

(Optional) Suppress the Neighbor Discovery on this subnetsuppress-nd

(Optional) Use eui64 interface identifiereui64


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 address <A:B::C:D/LEN> [scope <scope>] [preferred][suppress-nd] [eui64]

ipv6 address <A:B::C:D/LEN> eui64 preferred

Description: Configure IPv6 address on interface

Syntax:


Configure Extended Unique Identifier for the low-order 64 bitseui64

Configure IPv6 address as preferredpreferred


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 address <A:B::C:D/LEN> eui64 preferred


I Commandsipv6 address

ipv6 address <A:B::C:D/LEN> eui64 preferred

Description: Configure IPv6 address on interface

Syntax:


Configure Extended Unique Identifier for the low-order 64 bitseui64

Configure IPv6 address as preferredpreferred


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 address <A:B::C:D/LEN> eui64 preferred

ipv6 address <A:B:C::X/LEN> gateway <A:B:C::X>


Syntax:



Gateway IPv6 addressA:B:C::X


Command Path:

# configure [['terminal', 't']](config)# controller(config-controller)# interface mgmt0(config-controller-if)# ipv6 address <A:B:C::X/LEN> gateway <A:B:C::X>


Description: Configure IPv6 Address and Gateway

Syntax:







Command Path:

# configure [['terminal', 't']](config)# controller(config-controller)# interface inband-mgmt0(config-controller-if)# ipv6 address <A:B:C::X/LEN> gateway <A:B:C::X>



Syntax:





Command Path:

# configure [['terminal', 't']](config)# switch(config-switch)# interface mgmt0(config-switch-if)# ipv6 address <A:B:C::X/LEN> gateway <A:B:C::X>


Description: Configure IPv6 Address and Gateway

Syntax:





Command Path:

# configure [['terminal', 't']](config)# switch(config-switch)# interface inband-mgmt0(config-switch-if)# ipv6 address <A:B:C::X/LEN> gateway <A:B:C::X>



ipv6 address tenant applicationipv6 address <A:B::C:D> tenant <WORD> application <WORD> epg <WORD>


Syntax:

IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D







Command Path:

# configure [['terminal', 't']](config)# template dhcp relay policy <WORD>(config-template-dhcp-relay)# ipv6 address <A:B::C:D> tenant <WORD> application <WORD> epg<WORD>

ipv6 address <A:B::C:D> tenant <WORD> application <WORD> epg <WORD>


Syntax:









I Commandsipv6 address tenant application

Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template dhcp relay policy <WORD>(config-tenant-template-dhcp-relay)# ipv6 address <A:B::C:D> tenant <WORD> application<WORD> epg <WORD>


I Commandsipv6 address tenant application

ipv6 address tenant external-l2ipv6 address <A:B::C:D> tenant <WORD> external-l2 epg <WORD>


Syntax:




epg keywordepg



Command Path:

# configure [['terminal', 't']](config)# template dhcp relay policy <WORD>(config-template-dhcp-relay)# ipv6 address <A:B::C:D> tenant <WORD> external-l2 epg <WORD>

ipv6 address <A:B::C:D> tenant <WORD> external-l2 epg <WORD>


Syntax:




epg keywordepg



Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template dhcp relay policy <WORD>(config-tenant-template-dhcp-relay)# ipv6 address <A:B::C:D> tenant <WORD> external-l2 epg


I Commandsipv6 address tenant external-l2

<WORD>



ipv6 address tenant external-l3ipv6 address <A:B::C:D> tenant <WORD> external-l3 epg <WORD>


Syntax:




EPG keywordepg



Command Path:

# configure [['terminal', 't']](config)# template dhcp relay policy <WORD>(config-template-dhcp-relay)# ipv6 address <A:B::C:D> tenant <WORD> external-l3 epg <WORD>

ipv6 address <A:B::C:D> tenant <WORD> external-l3 epg <WORD>


Syntax:




EPG keywordepg



Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template dhcp relay policy <WORD>(config-tenant-template-dhcp-relay)# ipv6 address <A:B::C:D> tenant <WORD> external-l3 epg



<WORD>



ipv6 bandwidthipv6 bandwidth eigrp default <NUMBER>


Syntax:

EIGRPeigrp




Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 bandwidth eigrp default <NUMBER>

ipv6 bandwidth eigrp default <NUMBER>


Syntax:

EIGRPeigrp




Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 bandwidth eigrp default <NUMBER>


I Commandsipv6 bandwidth

ipv6 bfdipv6 bfd eigrp enable


Syntax:

EIGRPeigrp

Enable BFDenable


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 bfd eigrp enable

ipv6 bfd eigrp enable


Syntax:

EIGRPeigrp

Enable BFDenable


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 bfd eigrp enable


I Commandsipv6 bfd

ipv6 dhcp relay address tenant applicationipv6 dhcp relay address <A:B::C:D> tenant <WORD> application <WORD> epg <WORD>


Syntax:








Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 dhcp relay address <A:B::C:D> tenant <WORD> application<WORD> epg <WORD>


I Commandsipv6 dhcp relay address tenant application

ipv6 dhcp relay address tenant external-l2ipv6 dhcp relay address <A:B::C:D> tenant <WORD> external-l2 epg <WORD>


Syntax:




epg keywordepg



Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 dhcp relay address <A:B::C:D> tenant <WORD> external-l2 epg<WORD>


I Commandsipv6 dhcp relay address tenant external-l2

ipv6 dhcp relay address tenant external-l3ipv6 dhcp relay address <A:B::C:D> tenant <WORD> external-l3 epg <WORD>


Syntax:




EPG keywordepg



Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 dhcp relay address <A:B::C:D> tenant <WORD> external-l3 epg<WORD>


I Commandsipv6 dhcp relay address tenant external-l3

ipv6 distribute-list eigrpipv6 distribute-list eigrp default route-map <WORD> out

Description: Configure distribute-list EIGRP route-map

Syntax:


route maproute-map


outout


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 distribute-list eigrp default route-map <WORD> out

ipv6 distribute-list eigrp default route-map <WORD> out

Description: Configure distribute-list EIGRP Policies

Syntax:


route maproute-map


outout


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 distribute-list eigrp default route-map <WORD> out


I Commandsipv6 distribute-list eigrp

ipv6 hello-intervalipv6 hello-interval eigrp default <NUMBER>


Syntax:

EIGRPeigrp




Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 hello-interval eigrp default <NUMBER>

ipv6 hello-interval eigrp default <NUMBER>


Syntax:

EIGRPeigrp




Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 hello-interval eigrp default <NUMBER>


I Commandsipv6 hello-interval

ipv6 hold-intervalipv6 hold-interval eigrp default <NUMBER>


Syntax:

EIGRPeigrp




Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 hold-interval eigrp default <NUMBER>

ipv6 hold-interval eigrp default <NUMBER>


Syntax:

EIGRPeigrp




Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 hold-interval eigrp default <NUMBER>


I Commandsipv6 hold-interval

ipv6 link-localipv6 link-local <A:B::C:D>

Description: Configure IPv6 link-local address

Syntax:



Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 link-local <A:B::C:D>

ipv6 link-local <X:X:X:X::X>


Syntax:

IPv6 link-local addressX:X:X:X::X


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 link-local <X:X:X:X::X>

ipv6 link-local <X:X:X:X::X>


Syntax:

IPv6 link-local addressX:X:X:X::X


Command Path:



I Commandsipv6 link-local

(config-leaf-if)# ipv6 link-local <X:X:X:X::X>


I Commandsipv6 link-local

ipv6 nd hop-limitipv6 nd hop-limit <NUMBER>

Description: Set the hop limit to be advertised in IPv6 neighbor discovery packets

Syntax:

Hop Limit. Number range from=0 to=255<0-255>


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 nd hop-limit <NUMBER>

ipv6 nd hop-limit <NUMBER>


Syntax:


Command Mode: template ipv6 nd policy : Create/modify an an IPv6 Neighbor Discovery policy

Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ipv6 nd policy <WORD>(config-tenant-template-ipv6-nd)# ipv6 nd hop-limit <NUMBER>



Syntax:


Command Mode: template ipv6 nd policy : Configure IPv6 Neighbor Discovery policy templates

Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ipv6 nd policy <WORD> tenant <WORD>


I Commandsipv6 nd hop-limit

(config-template-nd-pol)# ipv6 nd hop-limit <NUMBER>



Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 nd hop-limit <NUMBER>



Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 nd hop-limit <NUMBER>


I Commandsipv6 nd hop-limit

ipv6 nd managed-config-flagipv6 nd managed-config-flag

Description: Use stateful address auto-configuration to obtain address information


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 nd managed-config-flag

ipv6 nd managed-config-flag



Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ipv6 nd policy <WORD>(config-tenant-template-ipv6-nd)# ipv6 nd managed-config-flag




Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ipv6 nd policy <WORD> tenant <WORD>(config-template-nd-pol)# ipv6 nd managed-config-flag




Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 nd managed-config-flag




I Commandsipv6 nd managed-config-flag


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 nd managed-config-flag


I Commandsipv6 nd managed-config-flag

ipv6 nd mtuipv6 nd mtu <NUMBER>

Description: Set the mtu to be advertised in IPv6 neighbor discovery packets

Syntax:

MTU value. Number range from=1280 to=9000<1280-9000>


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 nd mtu <NUMBER>

ipv6 nd mtu <NUMBER>


Syntax:



Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ipv6 nd policy <WORD>(config-tenant-template-ipv6-nd)# ipv6 nd mtu <NUMBER>



Syntax:



Command Path:



I Commandsipv6 nd mtu

(config-template-nd-pol)# ipv6 nd mtu <NUMBER>



Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 nd mtu <NUMBER>



Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 nd mtu <NUMBER>


I Commandsipv6 nd mtu

ipv6 nd ns-intervalipv6 nd ns-interval <NUMBER>

Description: Set the retransmission interval between IPv6 neighbor solicitation messages

Syntax:

Interval value. Number range from=1000 to=3600000<1000-3600000>


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 nd ns-interval <NUMBER>

ipv6 nd ns-interval <NUMBER>


Syntax:



Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ipv6 nd policy <WORD>(config-tenant-template-ipv6-nd)# ipv6 nd ns-interval <NUMBER>



Syntax:



Command Path:



I Commandsipv6 nd ns-interval

(config-template-nd-pol)# ipv6 nd ns-interval <NUMBER>



Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 nd ns-interval <NUMBER>



Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 nd ns-interval <NUMBER>


I Commandsipv6 nd ns-interval

ipv6 nd ns-retriesipv6 nd ns-retries <NUMBER>

Description: Set the retry count for for sending neighbor solicitation messages

Syntax:

Number of retries. Number range from=1 to=100<1-100>


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 nd ns-retries <NUMBER>

ipv6 nd ns-retries <NUMBER>


Syntax:



Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ipv6 nd policy <WORD>(config-tenant-template-ipv6-nd)# ipv6 nd ns-retries <NUMBER>



Syntax:



Command Path:



I Commandsipv6 nd ns-retries

(config-template-nd-pol)# ipv6 nd ns-retries <NUMBER>



Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 nd ns-retries <NUMBER>



Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 nd ns-retries <NUMBER>


I Commandsipv6 nd ns-retries

ipv6 nd other-config-flagipv6 nd other-config-flag

Description: Use stateful auto-configuration to obtain NON-address information


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 nd other-config-flag

ipv6 nd other-config-flag



Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ipv6 nd policy <WORD>(config-tenant-template-ipv6-nd)# ipv6 nd other-config-flag




Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ipv6 nd policy <WORD> tenant <WORD>(config-template-nd-pol)# ipv6 nd other-config-flag




Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 nd other-config-flag




I Commandsipv6 nd other-config-flag


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 nd other-config-flag


I Commandsipv6 nd other-config-flag

ipv6 nd policyipv6 nd policy <WORD>

Description: Associate the BD with an IPv6 Neighbor Discovery policy

Syntax:

Name of the policy to associate (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 nd policy <WORD>


I Commandsipv6 nd policy

ipv6 nd prefixipv6 nd prefix <A:B::C:D/LEN> <NUMBER> <NUMBER> [no-autoconfig] [no-onlink] [router-address]

Description: Advertise in Neighbor Discover a Prefix and configure the parameters

Syntax:


Lifetime to advertise for the prefix, in seconds. Number range from=0to=4294967295

<0-4294967295>

Preferred lifetime to advertise, in seconds. Number range from=0to=4294967295

<0-4294967295>

(Optional) advertise with A bit clearno-autoconfig

(Optional) advertise with L bit clearno-onlink

(Optional) Set this prefix as usable as default gateway by the hostsrouter-address


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 nd prefix <A:B::C:D/LEN> <NUMBER> <NUMBER> [no-autoconfig][no-onlink] [router-address]

ipv6 nd prefix <NUMBER> <NUMBER> [no-autoconfig] [no-onlink] [router-address]

Description: Advertise in Neighbor Discover a Prefix and configure the parameters

Syntax:

Lifetime to advertise for the prefix, in seconds. Number range from=0to=4294967295

<0-4294967295>

Preferred lifetime to advertise, in seconds. Number range from=0to=4294967295

<0-4294967295>

(Optional) advertise with A bit clearno-autoconfig

(Optional) advertise with L bit clearno-onlink

(Optional) Set this prefix as usable as default gateway by the hostsrouter-address


I Commandsipv6 nd prefix

Command Mode: template ipv6 nd prefix : Create/modify an an IPv6 Neighbor Prefix policy

Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ipv6 nd prefix policy <WORD>(config-tenant-template-ipv6-nd-pfx)# ipv6 nd prefix <NUMBER> <NUMBER> [no-autoconfig][no-onlink] [router-address]


I Commandsipv6 nd prefix

ipv6 nd ra-intervalipv6 nd ra-interval <NUMBER>

Description: Set the interval between sending ICMPv6 router advertisement messages

Syntax:



Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 nd ra-interval <NUMBER>

ipv6 nd ra-interval <NUMBER>


Syntax:



Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ipv6 nd policy <WORD>(config-tenant-template-ipv6-nd)# ipv6 nd ra-interval <NUMBER>



Syntax:



Command Path:



I Commandsipv6 nd ra-interval

(config-template-nd-pol)# ipv6 nd ra-interval <NUMBER>



Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 nd ra-interval <NUMBER>



Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 nd ra-interval <NUMBER>


I Commandsipv6 nd ra-interval

ipv6 nd ra-lifetimeipv6 nd ra-lifetime <NUMBER>

Description: Set the router lifetime of a default router in ICMPv6 router advertisement messages

Syntax:

Lifetime in seconds. Number range from=0 to=9000<0-9000>


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 nd ra-lifetime <NUMBER>

ipv6 nd ra-lifetime <NUMBER>


Syntax:



Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ipv6 nd policy <WORD>(config-tenant-template-ipv6-nd)# ipv6 nd ra-lifetime <NUMBER>



Syntax:



Command Path:



I Commandsipv6 nd ra-lifetime

(config-template-nd-pol)# ipv6 nd ra-lifetime <NUMBER>



Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 nd ra-lifetime <NUMBER>



Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 nd ra-lifetime <NUMBER>


I Commandsipv6 nd ra-lifetime

ipv6 nd reachable-timeipv6 nd reachable-time <NUMBER>

Description: Set the time for reachability confirmation in ICMPv6 router advertisement messages

Syntax:

Reachable timer in seconds. Number range from=0 to=3600000<0-3600000>


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 nd reachable-time <NUMBER>

ipv6 nd reachable-time <NUMBER>


Syntax:

Reachable timer in seconds. Number range from=0 to=3600000<0-3600000>


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ipv6 nd policy <WORD>(config-tenant-template-ipv6-nd)# ipv6 nd reachable-time <NUMBER>



Syntax:

Time in seconds. Number range from=0 to=3600000<0-3600000>


Command Path:



I Commandsipv6 nd reachable-time

(config-template-nd-pol)# ipv6 nd reachable-time <NUMBER>



Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 nd reachable-time <NUMBER>



Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 nd reachable-time <NUMBER>


I Commandsipv6 nd reachable-time

ipv6 nd retrans-timeripv6 nd retrans-timer <NUMBER>

Description: Set the time between neighbor solicitation (NS) messages in ICMPv6 router advertisement

Syntax:

Retransmit timer, in seconds. Number range from=0 to=4294967295<0-4294967295>


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 nd retrans-timer <NUMBER>

ipv6 nd retrans-timer <NUMBER>


Syntax:

Retransmit timer, in seconds. Number range from=0 to=4294967295<0-4294967295>


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ipv6 nd policy <WORD>(config-tenant-template-ipv6-nd)# ipv6 nd retrans-timer <NUMBER>



Syntax:

Timer in seconds. Number range from=0 to=4294967295<0-4294967295>


Command Path:



I Commandsipv6 nd retrans-timer

(config-template-nd-pol)# ipv6 nd retrans-timer <NUMBER>



Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 nd retrans-timer <NUMBER>



Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 nd retrans-timer <NUMBER>


I Commandsipv6 nd retrans-timer

ipv6 nd suppress-ra-mtuipv6 nd suppress-ra-mtu

Description: Disable sending MTU option in ICMPv6 router advertisement messages


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 nd suppress-ra-mtu

ipv6 nd suppress-ra-mtu



Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ipv6 nd policy <WORD>(config-tenant-template-ipv6-nd)# ipv6 nd suppress-ra-mtu




Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ipv6 nd policy <WORD> tenant <WORD>(config-template-nd-pol)# ipv6 nd suppress-ra-mtu




Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 nd suppress-ra-mtu




I Commandsipv6 nd suppress-ra-mtu


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 nd suppress-ra-mtu


I Commandsipv6 nd suppress-ra-mtu

ipv6 nd suppress-raipv6 nd suppress-ra

Description: Disable sending ICMPv6 router advertisement messages


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 nd suppress-ra

ipv6 nd suppress-ra



Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ipv6 nd policy <WORD>(config-tenant-template-ipv6-nd)# ipv6 nd suppress-ra

ipv6 nd suppress-ra



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ipv6 nd policy <WORD> tenant <WORD>(config-template-nd-pol)# ipv6 nd suppress-ra

ipv6 nd suppress-ra



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 nd suppress-ra

ipv6 nd suppress-ra



I Commandsipv6 nd suppress-ra


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 nd suppress-ra


I Commandsipv6 nd suppress-ra

ipv6 next-hop-selfipv6 next-hop-self eigrp default


Syntax:

EIGRPeigrp



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 next-hop-self eigrp default

ipv6 next-hop-self eigrp default


Syntax:

EIGRPeigrp



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 next-hop-self eigrp default


I Commandsipv6 next-hop-self

ipv6 ospf bfdipv6 ospf bfd enable


Syntax:

Enable BFDenable


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 ospf bfd enable

ipv6 ospf bfd enable


Syntax:

Enable BFDenable


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 ospf bfd enable


I Commandsipv6 ospf bfd

ipv6 ospf costipv6 ospf cost <NUMBER>


Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 ospf cost <NUMBER>

ipv6 ospf cost <NUMBER>


Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 ospf cost <NUMBER>


I Commandsipv6 ospf cost

ipv6 ospf dead-intervalipv6 ospf dead-interval <NUMBER>


Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 ospf dead-interval <NUMBER>

ipv6 ospf dead-interval <NUMBER>


Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 ospf dead-interval <NUMBER>


I Commandsipv6 ospf dead-interval

ipv6 ospf hello-intervalipv6 ospf hello-interval <NUMBER>


Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 ospf hello-interval <NUMBER>

ipv6 ospf hello-interval <NUMBER>


Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 ospf hello-interval <NUMBER>


I Commandsipv6 ospf hello-interval

ipv6 ospf inheritipv6 ospf inherit interface-policy <WORD> tenant <WORD>


Syntax:



tenant nametenant



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 ospf inherit interface-policy <WORD> tenant <WORD>

ipv6 ospf inherit interface-policy <WORD> tenant <WORD>


Syntax:



tenant nametenant



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 ospf inherit interface-policy <WORD> tenant <WORD>


I Commandsipv6 ospf inherit

ipv6 ospf mtu-ignoreipv6 ospf mtu-ignore



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 ospf mtu-ignore

ipv6 ospf mtu-ignore



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 ospf mtu-ignore


I Commandsipv6 ospf mtu-ignore

ipv6 ospf networkipv6 ospf network bcast|p2p|unspecified


Syntax:


bcast


p2p


unspecified


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 ospf network bcast|p2p|unspecified

ipv6 ospf network bcast|p2p|unspecified


Syntax:


bcast


p2p


unspecified


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 ospf network bcast|p2p|unspecified


I Commandsipv6 ospf network

ipv6 ospf passive-interfaceipv6 ospf passive-interface



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 ospf passive-interface

ipv6 ospf passive-interface



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 ospf passive-interface


I Commandsipv6 ospf passive-interface

ipv6 ospf prefix-suppressionipv6 ospf prefix-suppression disable|enable|inherit


Syntax:





Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 ospf prefix-suppression disable|enable|inherit

ipv6 ospf prefix-suppression disable|enable|inherit


Syntax:





Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 ospf prefix-suppression disable|enable|inherit


I Commandsipv6 ospf prefix-suppression

ipv6 ospf priorityipv6 ospf priority <NUMBER>


Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 ospf priority <NUMBER>

ipv6 ospf priority <NUMBER>


Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 ospf priority <NUMBER>


I Commandsipv6 ospf priority

ipv6 ospf retransmit-intervalipv6 ospf retransmit-interval <NUMBER>


Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 ospf retransmit-interval <NUMBER>

ipv6 ospf retransmit-interval <NUMBER>


Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 ospf retransmit-interval <NUMBER>


I Commandsipv6 ospf retransmit-interval

ipv6 ospf transmit-delayipv6 ospf transmit-delay <NUMBER>


Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 ospf transmit-delay <NUMBER>

ipv6 ospf transmit-delay <NUMBER>


Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 ospf transmit-delay <NUMBER>


I Commandsipv6 ospf transmit-delay

ipv6 passive-interfaceipv6 passive-interface eigrp default


Syntax:

EIGRPeigrp



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 passive-interface eigrp default

ipv6 passive-interface eigrp default


Syntax:

EIGRPeigrp



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 passive-interface eigrp default


I Commandsipv6 passive-interface

ipv6 router eigrpipv6 router eigrp default


Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 router eigrp default

ipv6 router eigrp default


Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 router eigrp default


I Commandsipv6 router eigrp

ipv6 router ospf defaultipv6 router ospf default area <A.B.C.D|NUMBER>


Syntax:




Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 router ospf default area <A.B.C.D|NUMBER>

ipv6 router ospf default area <A.B.C.D|NUMBER>


Syntax:




Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 router ospf default area <A.B.C.D|NUMBER>


I Commandsipv6 router ospf default

ipv6 shared address consumeripv6 shared address <A:B::C:D/LEN> consumer application any epg any

Description: Shared consumed service

Syntax:

IPv6 subnetaddress



any applicationany

epg keywordepg

any EPGany


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 shared address <A:B::C:D/LEN> consumer application any epgany


I Commandsipv6 shared address consumer

ipv6 shared address provideripv6 shared address <A:B::C:D/LEN> provider application <WORD> epg <WORD> [scope <scope>]

Description: Shared provider service

Syntax:

IPv6 subnetaddress




epg keywordepg

Application EPG (Max Size 64)WORD

(Optional) Scope of the address among ['public']scope


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 shared address <A:B::C:D/LEN> provider application <WORD>epg <WORD> [scope <scope>]


I Commandsipv6 shared address provider

ipv6 split-horizonipv6 split-horizon eigrp default


Syntax:

EIGRPeigrp



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 split-horizon eigrp default

ipv6 split-horizon eigrp default


Syntax:

EIGRPeigrp



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 split-horizon eigrp default


I Commandsipv6 split-horizon

ipv6 throughput-delayipv6 throughput-delay eigrp default <NUMBER> tens-of-micro|pico


Syntax:

EIGRPeigrp






Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 throughput-delay eigrp default <NUMBER> tens-of-micro|pico

ipv6 throughput-delay eigrp default <NUMBER> tens-of-micro|pico


Syntax:

EIGRPeigrp






Command Path:



I Commandsipv6 throughput-delay

(config-leaf-if)# ipv6 throughput-delay eigrp default <NUMBER> tens-of-micro|pico


I Commandsipv6 throughput-delay

isisisis fabric

Description: Intermediate System to Intermediate System (IS-IS)

Syntax:

Fabric IS-IS configurationfabric


Command Path:

# configure [['terminal', 't']](config)# pod 1(config-pod)# isis fabric


I Commandsisis

isolationisolation enforce

Description: Enable EPG isolation

Syntax:

Enable enforcing of policy-control rules (EPG isolation)enforce


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# isolation enforce


I Commandsisolation


I Commandsisolation

K Commands

• key, page 422


keykey <WORD>

Description: LDAP server key for authentication

Syntax:

server key (Max Size 32)<WORD>


Command Path:

# configure [['terminal', 't']](config)# ldap-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# key <WORD>

key <WORD>

Description: RADIUS server key for authentication

Syntax:

key for authentication (Max Size 32)<WORD>


Command Path:

# configure [['terminal', 't']](config)# radius-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# key <WORD>

key <WORD>

Description: TACACS server key for authentication

Syntax:

key for authentication (Max Size 32)<WORD>

Command Mode: tacacs-server host : TACACS+ server's DNS name or its IP address

Command Path:

# configure [['terminal', 't']](config)# tacacs-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# key <WORD>


K Commandskey

L Commands

• l2-unknown-unicast, page 425

• l3-unknown-multicast, page 426

• l3out, page 427

• l4l7-peer, page 428

• l4l7, page 429

• l4l7 cluster import-from, page 430

• l4l7 cluster name, page 431

• l4l7 graph, page 432

• label match, page 433

• label name, page 434

• lacp fast-select-hot-standby, page 435

• lacp graceful-convergence, page 436

• lacp load-defer, page 437

• lacp max-links, page 438

• lacp min-links, page 440

• lacp port-priority, page 442

• lacp port-priority interface, page 444

• lacp rate, page 445

• lacp rate fast normal interface, page 447

• lacp suspend-individual, page 448

• last-name, page 449

• ldap-server attribute, page 450

• ldap-server basedn, page 451

• ldap-server filter, page 452


• ldap-server host, page 453

• ldap-server retries, page 454

• ldap-server timeout, page 455

• leaf-group, page 456

• leaf-interface-group, page 457

• leaf-interface-profile, page 458

• leaf-policy-group, page 459

• leaf-profile, page 460

• leaf, page 461

• legacy, page 462

• link, page 463

• lldp, page 466

• lldp holdtime, page 469

• lldp reinit, page 470

• lldp timer, page 471

• local-as, page 472

• locality, page 473

• logfile, page 474

• logging, page 475

• logging audit, page 476

• logging description, page 477

• logging event, page 478

• logging fault, page 479

• logging server-group, page 480

• logging session, page 481

• logging severity, page 482

• lsp-fast-flood, page 484

• lsp-gen-interval, page 485

• lsp-mtu, page 486


L Commands

l2-unknown-unicastl2-unknown-unicast <WORD>

Description: Change Unknown Unicast flood behavior

Syntax:

Unicast Unknown threatmentWORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>(config-tenant-bd)# l2-unknown-unicast <WORD>


L Commandsl2-unknown-unicast

l3-unknown-multicastl3-unknown-multicast <WORD>

Description: Change L3 Multicast flood behavior

Syntax:

IP Multicast unknown Fram handlingWORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>(config-tenant-bd)# l3-unknown-multicast <WORD>


L Commandsl3-unknown-multicast

l3outl3out <WORD>

Description: Configuration for L3Out

Syntax:

L3Out name (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l3out <WORD>


L Commandsl3out

l4l7-peerl4l7-peer tenant <WORD> out <WORD> epg <WORD> redistribute WORD

Description: Configure l3external epg association for a l4l7 graph connector.

Syntax:

tenant under which the l3external epg residestenant

WORDWORD

l3external outside nameout

WORDWORD

l3external-epg nameepg

WORDWORD

Protocol Redistribute Settingsredistribute

Protocol Redistribute SettingsWORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 graph <WORD> [contract <contract-option>](config-graph)# service <WORD> [device-cluster-tenant <WORD>] [device-cluster <WORD>] [mode<Available Modes>](config-service)# connector <WORD> [cluster-interface <WORD>](config-connector)# l4l7-peer tenant <WORD> out <WORD> epg <WORD> redistribute WORD


L Commandsl4l7-peer

l4l7l4l7 graph <WORD>

Description: Associate a l4l7 graph with this subject

Syntax:

l4l7 graph to associate withgraph

Service Graph name (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# contract <WORD> [type <type>](config-tenant-contract)# subject <WORD>(config-tenant-contract-subj)# l4l7 graph <WORD>


L Commandsl4l7

l4l7 cluster import-froml4l7 cluster import-from <WORD> device-cluster <WORD>

Description: Import a L4-L7 Service Device Cluster

Syntax:


Device Cluster namedevice-cluster

Device cluster name (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 cluster import-from <WORD> device-cluster <WORD>


L Commandsl4l7 cluster import-from

l4l7 cluster namel4l7 cluster name <WORD> type <type> vlan-domain <domain-name> [service <service>] [function <function>]

Description: Add a L4-L7 Service Device Cluster

Syntax:

Device cluster name (Max Size 64)WORD

Type of l4l7 Device Clustertype

Type of l4l7 Device Clustertype

Physical or Virtual vlan domain to use for allocating encapsvlan-domain

Physical Or Virtual vlan domain to use for allocating encaps<domain-name>

(Optional) Indicates the type of service the device cluster providesservice

(Optional) Indicates the type of function the device cluster providesfunction


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 cluster name <WORD> type <type> vlan-domain <domain-name> [service<service>] [function <function>]


L Commandsl4l7 cluster name

l4l7 graphl4l7 graph <WORD> [contract <contract-option>]

Description: Configure L4-L7 Service Graph

Syntax:

Service Graph name (Max Size 64)WORD

(Optional) Name of Contractcontract-option


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 graph <WORD> [contract <contract-option>]


L Commandsl4l7 graph

label matchlabel match provider|consumer any|one|all|none

Description: Specify the match type for the provider or consumer label

Syntax:

Matching type for providerprovider

Matching type for consumerconsumer

Match if ANY label is found in the contract relationany

Match if exactly ONE label is found in the contract relationone

Match if ALL labels are found in the contract relationall

Match if NO labels are found in the contract relationnone


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# contract <WORD> [type <type>](config-tenant-contract)# subject <WORD>(config-tenant-contract-subj)# label match provider|consumer any|one|all|none


L Commandslabel match

label namelabel name <WORD> provider|consumer

Description: Add a provider or consumer label to the subject

Syntax:

Name of the label to add (Max Size 64)WORD

Matching type for providerprovider

Matching type for consumerconsumer


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# contract <WORD> [type <type>](config-tenant-contract)# subject <WORD>(config-tenant-contract-subj)# label name <WORD> provider|consumer


L Commandslabel name

lacp fast-select-hot-standbylacp fast-select-hot-standby

Description: Enable LACP fast select for hot standby ports


Command Path:

# configure [['terminal', 't']](config)# template port-channel <WORD>(config-if)# lacp fast-select-hot-standby

lacp fast-select-hot-standby



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# lacp fast-select-hot-standby

lacp fast-select-hot-standby



Command Path:

# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# lacp fast-select-hot-standby


L Commandslacp fast-select-hot-standby

lacp graceful-convergencelacp graceful-convergence

Description: Enable LACP graceful convergence


Command Path:

# configure [['terminal', 't']](config)# template port-channel <WORD>(config-if)# lacp graceful-convergence

lacp graceful-convergence



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# lacp graceful-convergence

lacp graceful-convergence



Command Path:

# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# lacp graceful-convergence


L Commandslacp graceful-convergence

lacp load-deferlacp load-defer

Description: Enable LACP load defer member ports


Command Path:

# configure [['terminal', 't']](config)# template port-channel <WORD>(config-if)# lacp load-defer

lacp load-defer



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# lacp load-defer

lacp load-defer



Command Path:

# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# lacp load-defer


L Commandslacp load-defer

lacp max-linkslacp max-links <NUMBER>

Description: Configure maximum number of links

Syntax:

Range 1 to 16. Number range from=1 to=16<number>


Command Path:

# configure [['terminal', 't']](config)# template port-channel <WORD>(config-if)# lacp max-links <NUMBER>

lacp max-links <NUMBER>


Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# lacp max-links <NUMBER>

lacp max-links <NUMBER>


Syntax:



Command Path:



L Commandslacp max-links

(config-vpc-if)# lacp max-links <NUMBER>


L Commandslacp max-links

lacp min-linkslacp min-links <NUMBER>

Description: Configure minimum number of links

Syntax:



Command Path:

# configure [['terminal', 't']](config)# template port-channel <WORD>(config-if)# lacp min-links <NUMBER>

lacp min-links <NUMBER>


Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# lacp min-links <NUMBER>

lacp min-links <NUMBER>


Syntax:



Command Path:



L Commandslacp min-links

(config-vpc-if)# lacp min-links <NUMBER>


L Commandslacp min-links

lacp port-prioritylacp port-priority <arg>

Description: Set Lacp priority

Syntax:

Priority Value. Number range from=1 to=65535arg


Command Path:

# configure [['terminal', 't']](config)# leaf-interface-profile <WORD>(config-leaf-if-profile)# leaf-interface-group <WORD>(config-leaf-if-group)# lacp port-priority <>

lacp port-priority <arg>

Description: Set Lacp priority.

Syntax:



Command Path:

# configure [['terminal', 't']](config)# fex-profile <WORD>(config-fex-profile)# fex-interface-group <WORD>(config-fex-if-group)# lacp port-priority <>

lacp port-priority <NUMBER>

Description: Set Lacp priority.

Syntax:

Priority Value. Number range from=1 to=65535<1-65535>


Command Path:



L Commandslacp port-priority

(config-leaf-if)# lacp port-priority <NUMBER>


L Commandslacp port-priority

lacp port-priority interfacelacp port-priority <arg> interface ethernet

Description: Set Port Priority on specific Ports

Syntax:





Command Path:

# configure [['terminal', 't']](config)# leaf-interface-profile <WORD>(config-leaf-if-profile)# leaf-interface-group <WORD>(config-leaf-if-group)# lacp port-priority <> interface ethernet

lacp port-priority <arg> interface ethernet


Syntax:





Command Path:

# configure [['terminal', 't']](config)# fex-profile <WORD>(config-fex-profile)# fex-interface-group <WORD>(config-fex-if-group)# lacp port-priority <> interface ethernet


L Commandslacp port-priority interface

lacp ratelacp rate fast|normal

Description: Set Lacp rate

Syntax:

Set rate to fastfast

Set rate to normalnormal


Command Path:

# configure [['terminal', 't']](config)# leaf-interface-profile <WORD>(config-leaf-if-profile)# leaf-interface-group <WORD>(config-leaf-if-group)# lacp rate fast|normal

lacp rate fast|normal


Syntax:




Command Path:

# configure [['terminal', 't']](config)# fex-profile <WORD>(config-fex-profile)# fex-interface-group <WORD>(config-fex-if-group)# lacp rate fast|normal

lacp rate fast|normal


Syntax:




L Commandslacp rate


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# lacp rate fast|normal


L Commandslacp rate

lacp rate fast normal interfacelacp rate fast|normal interface ethernet


Syntax:






Command Path:

# configure [['terminal', 't']](config)# leaf-interface-profile <WORD>(config-leaf-if-profile)# leaf-interface-group <WORD>(config-leaf-if-group)# lacp rate fast|normal interface ethernet

lacp rate fast|normal interface ethernet


Syntax:






Command Path:

# configure [['terminal', 't']](config)# fex-profile <WORD>(config-fex-profile)# fex-interface-group <WORD>(config-fex-if-group)# lacp rate fast|normal interface ethernet


L Commandslacp rate fast normal interface

lacp suspend-individuallacp suspend-individual

Description: Enable LACP individual Port suspension


Command Path:

# configure [['terminal', 't']](config)# template port-channel <WORD>(config-if)# lacp suspend-individual

lacp suspend-individual



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# lacp suspend-individual

lacp suspend-individual



Command Path:

# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# lacp suspend-individual


L Commandslacp suspend-individual

last-namelast-name <WORD>

Description: Set The last name of the locally-authenticated user.

Syntax:

last name (Max Size 32)WORD


Command Path:

# configure [['terminal', 't']](config)# username <WORD>(config-username)# last-name <WORD>


L Commandslast-name

ldap-server attributeldap-server attribute <WORD>

Description: An LDAP endpoint attribute to be used as the CiscoAVPair

Syntax:

LDAP endpoint attribute (Max Size 63)<WORD>


Command Path:

# configure [['terminal', 't']](config)# ldap-server attribute <WORD>


L Commandsldap-server attribute

ldap-server basednldap-server basedn <WORD>

Description: The LDAP base DN for user lookup in the LDAP directory tree

Syntax:



Command Path:

# configure [['terminal', 't']](config)# ldap-server basedn <WORD>


L Commandsldap-server basedn

ldap-server filterldap-server filter <WORD>

Description: LDAP search filter for the LDAP endpoint

Syntax:

search filter for the LDAP endpoint (Max Size 63)<WORD>


Command Path:

# configure [['terminal', 't']](config)# ldap-server filter <WORD>


L Commandsldap-server filter

ldap-server hostldap-server host <A.B.C.D|A:B::C:D|WORD>

Description: LDAP server DNS name or IP address

Syntax:

Provide a hostname or IPV4/IPV6 addressA.B.C.D|A:B::C:D|WORD


Command Path:

# configure [['terminal', 't']](config)# ldap-server host <A.B.C.D|A:B::C:D|WORD>


L Commandsldap-server host

ldap-server retriesldap-server retries <NUMBER>

Description: Global LDAP server retransmit count

Syntax:

Global LDAP server retransmit count. Number range from=0 to=5<0-5>


Command Path:

# configure [['terminal', 't']](config)# ldap-server retries <NUMBER>


L Commandsldap-server retries

ldap-server timeoutldap-server timeout <NUMBER>

Description: Global LDAP server timeout period in seconds

Syntax:

Global LDAP server timeout period in seconds. Number range from=1to=60

<1-60>


Command Path:

# configure [['terminal', 't']](config)# ldap-server timeout <NUMBER>


L Commandsldap-server timeout

leaf-groupleaf-group <WORD>

Description: Configure Leaf Group

Syntax:

Leaf Group name (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# leaf-profile <WORD>(config-leaf-profile)# leaf-group <WORD>


L Commandsleaf-group

leaf-interface-groupleaf-interface-group <WORD>

Description: Configure Leaf Interface Group

Syntax:

Leaf Interface Group name (Max Size 64)WORD

Command Mode: leaf-interface-profile : Create Leaf Interface Profile

Command Path:

# configure [['terminal', 't']](config)# leaf-interface-profile <WORD>(config-leaf-if-profile)# leaf-interface-group <WORD>


L Commandsleaf-interface-group

leaf-interface-profileleaf-interface-profile <WORD>

Description: Create Leaf Interface Profile

Syntax:

Leaf Interface Profile name (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# leaf-interface-profile <WORD>

leaf-interface-profile <WORD>

Description: Attach Leaf Interface Profile to the Leaf Profile

Syntax:

Leaf Interface Profile name (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# leaf-profile <WORD>(config-leaf-profile)# leaf-interface-profile <WORD>


L Commandsleaf-interface-profile

leaf-policy-groupleaf-policy-group <WORD>

Description: Configure leaf policy group

Syntax:

Leaf policy name (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# leaf-profile <WORD>(config-leaf-profile)# leaf-group <WORD>(config-leaf-group)# leaf-policy-group <WORD>


L Commandsleaf-policy-group

leaf-profileleaf-profile <WORD>

Description: Configure Leaf Profile

Syntax:

Leaf Profile name (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# leaf-profile <WORD>


L Commandsleaf-profile

leafleaf <101-4000>

Description: Provide a Range of Nodes

Syntax:

Leaf Range or Leaf Name List<101-4000>


Command Path:

# configure [['terminal', 't']](config)# leaf-profile <WORD>(config-leaf-profile)# leaf-group <WORD>(config-leaf-group)# leaf <101-4000>

leaf <101-4000>

Description: Configure Leaf Node

Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>


L Commandsleaf

legacylegacy forwarding vlan <NUMBER> vlan-domain <WORD>

Description: Set the bridge domain to behave as a L2 vlan in traditional ethernet environment

Syntax:

Forwarding keywordforwarding

Legacy Vlan Numbervlan

Legacy Vlan Number. Number range from=1 to=4094<1-4094>

Name of the vlan domain to usevlan-domain

Name of the vlan domain to use (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>(config-tenant-bd)# legacy forwarding vlan <NUMBER> vlan-domain <WORD>


L Commandslegacy

linklink debounce time <NUMBER>

Description: Configure link

Syntax:

Configure link debounce timerdebounce

Link debounce timetime

Timer value (in milliseconds). Number range from=0 to=5000<time>


Command Path:

# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# link debounce time <NUMBER>

link debounce time <NUMBER>


Syntax:





Command Path:

# configure [['terminal', 't']](config)# template port-channel <WORD>(config-if)# link debounce time <NUMBER>



Syntax:



L Commandslink




Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# link debounce time <NUMBER>



Syntax:





Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# link debounce time <NUMBER>



Syntax:





Command Path:



L Commandslink

(config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# link debounce time <NUMBER>


L Commandslink

lldplldp receive|transmit|both|default

Description: Configure Interface LLDP parameters on DVS uplink ports

Syntax:

Enable LLDP receptionreceive

Enable LLDP transmissiontransmit

Enable LLDP in both directionsboth

Remove LLDP override policydefault


Command Path:

# configure [['terminal', 't']](config)# vmware-domain <WORD>(config-vmware)# configure-dvs(config-vmware-dvs)# lldp receive|transmit|both|default

lldp receive|transmit|both|default

Description: Configure Interface LLDP parameters on AVS uplink ports

Syntax:

Enable LLDP receptionreceive

Enable LLDP transmissiontransmit

Enable LLDP in both directionsboth

Remove LLDP override policydefault


Command Path:

# configure [['terminal', 't']](config)# vmware-domain <WORD>(config-vmware)# configure-avs(config-vmware-avs)# lldp receive|transmit|both|default


L Commandslldp

lldp receive|transmit

Description: Configure Interface LLDP parameters

Syntax:

Enable LLDP reception on interfacereceive

Enable LLDP transmission on interfacetransmit


Command Path:

# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# lldp receive|transmit



Syntax:




Command Path:

# configure [['terminal', 't']](config)# template port-channel <WORD>(config-if)# lldp receive|transmit



Syntax:




Command Path:



L Commandslldp

(config-leaf-if)# lldp receive|transmit



Syntax:




Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# lldp receive|transmit



Syntax:




Command Path:

# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# lldp receive|transmit


L Commandslldp

lldp holdtimelldp holdtime <NUMBER>

Description: Specify the hold time to be sent in LLDP packets

Syntax:

Holdtime in sec. Number range from=10 to=255<10-255>


Command Path:

# configure [['terminal', 't']](config)# lldp holdtime <NUMBER>


L Commandslldp holdtime

lldp reinitlldp reinit <NUMBER>

Description: Specify the delay for LLDP initialization on an interface

Syntax:

Reinit Delay in sec. Number range from=1 to=10<1-10>


Command Path:

# configure [['terminal', 't']](config)# lldp reinit <NUMBER>


L Commandslldp reinit

lldp timerlldp timer <NUMBER>

Description: Specify the rate at which LLDP packets are sent

Syntax:

Rate of packets in sec. Number range from=5 to=254<5-254>


Command Path:

# configure [['terminal', 't']](config)# lldp timer <NUMBER>


L Commandslldp timer

local-aslocal-as <NUMBER> no-prepend|replace-as|dual-as

Description: Local Autonomous System Configuration for a BGP Peer

Syntax:

The local autonomous system number. Number range from=1to=4294967295

<1-4294967295>

Do not prepend local-as to updates from ebgp peersno-prepend

Replace real AS with local AS in the EBGP updatesreplace-as

Accept either real AS or local AS from the ebgp peerdual-as


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [l3out <WORD>](config-leaf-bgp-vrf-neighbor)# local-as <NUMBER> no-prepend|replace-as|dual-as


L Commandslocal-as

localitylocality <WORD>

Description: Set The city or town of the organization.

Syntax:

city or town (Max Size 64)<WORD>


Command Path:

# configure [['terminal', 't']](config)# crypto keyring <WORD>(config-keyring)# csr(config-csr)# locality <WORD>


L Commandslocality

logfilelogfile [severity <severity>]

Description: Enable the logging to logfile

Syntax:

(Optional) The severity level for the logsseverity


Command Path:

# configure [['terminal', 't']](config)# logging server-group <WORD>(config-logging)# logfile [severity <severity>]


L Commandslogfile

logginglogging server-group <WORD>

Description: Logging server group configuration mode

Syntax:

Logging Server-Group configurationserver-group



Command Path:

# configure [['terminal', 't']](config)# logging server-group <WORD>


L Commandslogging

logging auditlogging audit

Description: Enable audit and session logs to the policy


Command Path:

# configure [['terminal', 't']](config)# callhome common(config-callhome)# logging audit

logging audit

Description: Enable audit logs to the policy

Command Mode: syslog : Syslog common policy configuration mode

Command Path:

# configure [['terminal', 't']](config)# syslog common(config-syslog)# logging audit


L Commandslogging audit

logging descriptionlogging description <WORD>

Description: Add description for syslog common

Syntax:

Description (Max Size 128) surrounded by single quotesWORD


Command Path:

# configure [['terminal', 't']](config)# syslog common(config-syslog)# logging description <WORD>


L Commandslogging description

logging eventlogging event

Description: Enable event logs to the policy


Command Path:

# configure [['terminal', 't']](config)# callhome common(config-callhome)# logging event

logging event

Description: Enable event logs to the policy


Command Path:

# configure [['terminal', 't']](config)# syslog common(config-syslog)# logging event


L Commandslogging event

logging faultlogging fault

Description: Enable fault logs to the policy


Command Path:

# configure [['terminal', 't']](config)# callhome common(config-callhome)# logging fault

logging fault

Description: Enable fault logs to the policy


Command Path:

# configure [['terminal', 't']](config)# syslog common(config-syslog)# logging fault


L Commandslogging fault

logging server-grouplogging server-group <WORD>

Description: Logging server group configuration

Syntax:



Command Path:

# configure [['terminal', 't']](config)# syslog common(config-syslog)# logging server-group <WORD>


L Commandslogging server-group

logging sessionlogging session

Description: Enable session logs to the policy


Command Path:

# configure [['terminal', 't']](config)# syslog common(config-syslog)# logging session


L Commandslogging session

logging severitylogging severity info|notice|emergency|alert|critical|error|debug|warning

Description: Configure minimum severity level for logs generated

Syntax:

Infoinfo

Noticenotice

Emergencyemergency

Alertalert

Criticalcritical

Errorerror

Debugdebug

Warningwarning


Command Path:

# configure [['terminal', 't']](config)# callhome common(config-callhome)# logging severity info|notice|emergency|alert|critical|error|debug|warning

logging severity emergencies|debugging|critical|errors|warnings|information|alerts|notifications

Description: Configure minimum severity level for logs generated

Syntax:

Emergenciesemergencies

Debuggingdebugging

Criticalcritical

Errorserrors

Warningswarnings

Informationinformation


L Commandslogging severity

Alertsalerts

Notificationsnotifications


Command Path:

# configure [['terminal', 't']](config)# syslog common(config-syslog)# logging severityemergencies|debugging|critical|errors|warnings|information|alerts|notifications


L Commandslogging severity

lsp-fast-floodlsp-fast-flood

Description: Enables the ISIS LSP fast flood

Command Mode: isis : Intermediate System to Intermediate System (IS-IS)

Command Path:

# configure [['terminal', 't']](config)# pod 1(config-pod)# isis fabric(config-pod-isis)# lsp-fast-flood


L Commandslsp-fast-flood

lsp-gen-intervallsp-gen-interval level-1 <NUMBER> <50-120000> <50-120000>

Description: Set the ISIS LSP generation maximal wait interval

Syntax:

Level 1level-1

LSP generation maximum wait interval. Number range from=50to=120000

<50-120000>

Initial and secondary wait intervals (both values are required)<50-120000> <50-120000>


Command Path:

# configure [['terminal', 't']](config)# pod 1(config-pod)# isis fabric(config-pod-isis)# lsp-gen-interval level-1 <NUMBER> <50-120000> <50-120000>


L Commandslsp-gen-interval

lsp-mtulsp-mtu <NUMBER>

Description: Set the configuration of link-state packet (LSP) maximum transmission units (MTU) value

Syntax:

The configuration of link-state packet (LSP) maximum transmissionunits (MTU).. Number range from=256 to=4352

<256-4352>


Command Path:

# configure [['terminal', 't']](config)# pod 1(config-pod)# isis fabric(config-pod-isis)# lsp-mtu <NUMBER>


L Commandslsp-mtu

M Commands

• mac-address, page 489

• match, page 491

• match arp, page 492

• match bridge-domain, page 493

• match community, page 494

• match icmp, page 495

• match ip, page 496

• match ipv6, page 497

• match prefix-list, page 498

• match raw, page 499

• match tcp, page 500

• match udp, page 501

• max-lsa, page 502

• max-validity-period, page 503

• max concurrent, page 504

• max running, page 505

• maximum-paths, page 506

• maximum-prefix, page 508

• mcp, page 509

• mcp action, page 511

• mcp enable, page 512

• mcp factor, page 513

• mcp init-delay, page 514

• mcp transmit-frequency, page 515


• member, page 516

• message-level, page 517

• message-size, page 518

• metric, page 519

• mgmt-epg, page 520

• microsoft-domain, page 521

• microsoft, page 522

• min-rx, page 523

• min-tx, page 524

• min, page 525

• mode, page 526

• modulus, page 527

• monitor, page 528

• monitor access, page 529

• monitor fabric, page 530

• monitor tenant, page 531

• monitor virtual, page 532

• mtu-ignore, page 533

• mtu, page 534

• multi-destination, page 537

• multi-site-mac-address, page 538

• multicast-address, page 539

• multiplier, page 540


M Commands

mac-addressmac-address E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE

Description: Add a custom MAC address to the bridgedomain

Syntax:






Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# mac-addressE.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE

mac-address E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE

Description:Manually set interface MAC address

Syntax:






Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# mac-address E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE


M Commandsmac-address

mac-address E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE

Description: Configure mac Address

Syntax:






Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# mac-address E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE


M Commandsmac-address

matchmatch dscp|dot1p <WORD> <WORD> [set-class <WORD>] [set-dscp <WORD>]

Description: Add a rule to match DSCP or DOT1P, queue the traffic and optionally mutate it

Syntax:

Match entry for DSCPdscp

Match entry for DOT1Pdot1p

From of DSCP or DOT1P rangeWORD

To of DSCP or DOT1P rangeWORD

(Optional) Set the QOS class for the trafficWORD

(Optional) DSCP rewriteWORD

Command Mode: policy-map type qos : QOS policy type

Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type qos <WORD>(config-tenant-pmap-qos)# match dscp|dot1p <WORD> <WORD> [set-class <WORD>] [set-dscp <WORD>]


M Commandsmatch

match arpmatch arp

Description:Match the ARP traffic

Command Mode: access-list : Create access-list

Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# access-list <WORD>(config-tenant-acl)# match arp


M Commandsmatch arp

match bridge-domainmatch bridge-domain <arg>

Description:Match subnets of a bridge-domain

Syntax:

arg


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match bridge-domain <>


M Commandsmatch bridge-domain

match communitymatch community <WORD>

Description: Configure community features

Syntax:

Name of communityWORD


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match community <WORD>


M Commandsmatch community

match icmpmatch icmp

Description:Match the ICMP traffic


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# access-list <WORD>(config-tenant-acl)# match icmp


M Commandsmatch icmp

match ipmatch ip

Description:Match the IP traffic


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# access-list <WORD>(config-tenant-acl)# match ip

match ip <A.B.C.D/LEN> [shared]

Description: Add a subnet that identify hosts being part of the epg

Syntax:

IP prefix and network mask lengthA.B.C.D/LEN

(Optional) Add the shared scope to the existing scope for the subnetshared


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l3 epg <WORD> [oob-mgmt] [l3out <l3out>](config-tenant-l3ext-epg)# match ip <A.B.C.D/LEN> [shared]


M Commandsmatch ip

match ipv6match ipv6 X:X:X:X::X/<0-128>

Description: Add a subnet that identify hosts being part of the epg

Syntax:

IPv6 prefix and network mask lengthX:X:X:X::X/<0-128>


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l3 epg <WORD> [oob-mgmt] [l3out <l3out>](config-tenant-l3ext-epg)# match ipv6 X:X:X:X::X/<0-128>


M Commandsmatch ipv6

match prefix-listmatch prefix-list <WORD>

Description:Match entries of a prefix-list

Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match prefix-list <WORD>


M Commandsmatch prefix-list

match rawmatch raw <WORD> [tcpRules <tcpRules>] [arpOpc <arpOpc>] [applyToFrag <applyToFrag>] [dToPort<NUMBER>] [prot <NUMBER>] [icmpv4T <icmpv4T>] [stateful <stateful>] [icmpv6T <icmpv6T>] [sToPort<NUMBER>] [etherT <etherT>] [sFromPort <NUMBER>] [dFromPort <NUMBER>]

Description: Specify a raw vzEntry

Syntax:

Entry Name (Max Size 64)WORD

(Optional) TCP Flags as comma separated values like val1,val2,..valNtcpRules

(Optional) ARP OpcodesarpOpc

(Optional) Apply to FragmentapplyToFrag

(Optional) L4 Destination Port. Number range from=0 to=65535<0-65535>

(Optional) IP Protocol. Number range from=0 to=255<0-255>

(Optional) ICMP Typeicmpv4T

(Optional) Stateful flagstateful

(Optional) ICMPv6 Typeicmpv6T

(Optional) L4 Source Port. Number range from=0 to=65535<0-65535>

(Optional) Ethernet TypeetherT

(Optional) L4 Source Port. Number range from=0 to=65535<0-65535>

(Optional) L4 Destination Port. Number range from=0 to=65535<0-65535>


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# access-list <WORD>(config-tenant-acl)# match raw <WORD> [tcpRules <tcpRules>] [arpOpc <arpOpc>] [applyToFrag<applyToFrag>] [dToPort <NUMBER>] [prot <NUMBER>] [icmpv4T <icmpv4T>] [stateful <stateful>][icmpv6T <icmpv6T>] [sToPort <NUMBER>] [etherT <etherT>] [sFromPort <NUMBER>] [dFromPort<NUMBER>]


M Commandsmatch raw

match tcpmatch tcp [src <from>-[<to>] contained in <0-65535>] [dest <from>-[<to>] contained in <0-65535>]

Description:Match TCP traffic

Syntax:

(Optional) TCP Source port Range<from>-[<to>] contained in<0-65535>

(Optional) TCP Destination port Range<from>-[<to>] contained in<0-65535>


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# access-list <WORD>(config-tenant-acl)# match tcp [src <from>-[<to>] contained in <0-65535>] [dest <from>-[<to>]contained in <0-65535>]


M Commandsmatch tcp

match udpmatch udp [src <from>-[<to>] contained in <0-65535>] [dest <from>-[<to>] contained in <0-65535>]

Description:Match UDP traffic

Syntax:

(Optional) UDP Source port Range<from>-[<to>] contained in<0-65535>

(Optional) UDP Destination port Range<from>-[<to>] contained in<0-65535>


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# access-list <WORD>(config-tenant-acl)# match udp [src <from>-[<to>] contained in <0-65535>] [dest <from>-[<to>]contained in <0-65535>]


M Commandsmatch udp

max-lsamax-lsa <NUMBER> <NUMBER> reject|restart|log

Description: Feature to limit the number of non-self-originated LSAs

Syntax:

Set maximum number of non self-generated LSAs. Number rangefrom=1 to=4294967295

<1-4294967295>

Threshold value (%) at which to generate a warning message. Numberrange from=1 to=100

<1-100>

Reject LSAs beyond the limitreject

Restart the neighborrestart

log a warninglog


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf vrf-policy <WORD> tenant <WORD>(config-vrf-policy)# max-lsa <NUMBER> <NUMBER> reject|restart|log


M Commandsmax-lsa

max-validity-periodmax-validity-period <NUMBER>

Description: Set The maximum validity period for a webtoken

Syntax:

Set Themaximumvalidity period for a webtoken. Number range from=4to=24

<4-24>

Command Mode: crypto webtoken : The cryptographic data used for generating and verifying web tokens.

Command Path:

# configure [['terminal', 't']](config)# crypto webtoken(config-webtoken)# max-validity-period <NUMBER>


M Commandsmax-validity-period

max concurrentmax concurrent nodes <NUMBER>

Description: Set the window maximum concurrent node limit

Syntax:

Maximum number of tasks that can be processed concurrently.nodes

Enter maximum number of concurrent nodes. 0 for unlimited. Numberrange from=0 to=65535

<0-65535>

Command Mode: absolute : Absolute window configuration mode

Command Path:

# configure [['terminal', 't']](config)# scheduler fabric|controller schedule <WORD>(config-scheduler)# absolute window <WORD>(config-scheduler-absolute)# max concurrent nodes <NUMBER>

max concurrent nodes <NUMBER>

Description: Set the window maximum concurrent node limit

Syntax:

Maximum number of tasks that can be processed concurrently.nodes

Enter maximum number of concurrent nodes. 0 for unlimited. Numberrange from=0 to=65535

<0-65535>

Command Mode: recurring : Recurring window configuration mode

Command Path:

# configure [['terminal', 't']](config)# scheduler fabric|controller schedule <WORD>(config-scheduler)# recurring window <WORD>(config-scheduler-recurring)# max concurrent nodes <NUMBER>


M Commandsmax concurrent

max runningmax running time <TIME>

Description: Set the window maximum running time

Syntax:

Maximum running timetime

Enter the maximum running time in dd:hh:mm:ss. 0 for unlimitedTIME


Command Path:

# configure [['terminal', 't']](config)# scheduler fabric|controller schedule <WORD>(config-scheduler)# absolute window <WORD>(config-scheduler-absolute)# max running time <TIME>

max running time <TIME>

Description: Set the window maximum running time

Syntax:

Maximum running time in millisecondstime

Enter the maximum running time in dd:hh:mm:ss. 0 for unlimitedTIME


Command Path:

# configure [['terminal', 't']](config)# scheduler fabric|controller schedule <WORD>(config-scheduler)# recurring window <WORD>(config-scheduler-recurring)# max running time <TIME>


M Commandsmax running

maximum-pathsmaximum-paths <NUMBER>

Description: Set the maximum ECMP for the OSPF protocol

Syntax:

Maximum paths. Number range from=1 to=64<1-64>


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf vrf-policy <WORD> tenant <WORD>(config-vrf-policy)# maximum-paths <NUMBER>

maximum-paths <NUMBER>

Description: Set EIGRP Maximum Path Limit

Syntax:

Maximum Path Limit. Number range from=1 to=32<1-32>


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template eigrp vrf-policy <WORD> tenant <WORD>(config-template-eigrp-vrf-pol)# maximum-paths <NUMBER>

maximum-paths <NUMBER>

Description: Set EIGRP Maximum Path Limit

Syntax:

Maximum Path Limit. Number range from=1 to=32<1-32>


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router eigrp default


M Commandsmaximum-paths

(config-eigrp)# vrf member tenant <WORD> vrf <WORD>(config-eigrp-vrf)# address-family ipv4|ipv6 unicast(config-address-family)# maximum-paths <NUMBER>


M Commandsmaximum-paths

maximum-prefixmaximum-prefix <NUMBER> [action <action>] [threshold <NUMBER>] [restart-time <NUMBER>]

Description:Maximum number of prefixes from this neighbor

Syntax:

Max. prefix limit. Number range from=1 to=300000<1-300000>

(Optional) Action to be performed when the maximum prefix limit isreached

<action>

(Optional) The threshold % of the maximum number of prefixes beforea warning is issued. Number range from=1 to=100

<1-100>

(Optional) The period of time in minutes before restarting the peer whenthe prefix limit is reached. Number range from=1 to=65535

<1-65535>

Command Mode: address-family : Configure an address-family for peer

Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [l3out <WORD>](config-leaf-bgp-vrf-neighbor)# address-family ipv4|ipv6 unicast(config-leaf-bgp-vrf-neighbor-af)# maximum-prefix <NUMBER> [action <action>] [threshold<NUMBER>] [restart-time <NUMBER>]


M Commandsmaximum-prefix

mcpmcp enable

Description: Configure MCP interface parameters

Syntax:

Configure MCP parametersenable


Command Path:

# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# mcp enable

mcp enable


Syntax:



Command Path:

# configure [['terminal', 't']](config)# template port-channel <WORD>(config-if)# mcp enable

mcp enable


Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# mcp enable


M Commandsmcp

mcp enable


Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# mcp enable

mcp enable


Syntax:



Command Path:

# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# mcp enable


M Commandsmcp

mcp actionmcp action port-disable

Description: Configure MCP Loop Protection Action

Syntax:

Disable the port when MCP detects loopport-disable


Command Path:

# configure [['terminal', 't']](config)# mcp action port-disable


M Commandsmcp action

mcp enablemcp enable key <WORD>

Description: Enable/Disable MCP Protocol

Syntax:

Configure MCP keykey

MCP keyWORD


Command Path:

# configure [['terminal', 't']](config)# mcp enable key <WORD>


M Commandsmcp enable

mcp factormcp factor <NUMBER>

Description: Configure MCP Loop Detection Factor

Syntax:

MCP Loop Detection Multipication Factor. Number range from=1to=255

<1-255>


Command Path:

# configure [['terminal', 't']](config)# mcp factor <NUMBER>


M Commandsmcp factor

mcp init-delaymcp init-delay <NUMBER>

Description: Configure MCP Loop Detection Init Delay Time

Syntax:

MCP Loop Detection Init Delay Time. Number range from=0 to=1800<0-1800>


Command Path:

# configure [['terminal', 't']](config)# mcp init-delay <NUMBER>


M Commandsmcp init-delay

mcp transmit-frequencymcp transmit-frequency <NUMBER>

Description: Configure MCP Advertisement Transmit Frequency

Syntax:

MCP Advertisement Tx Frequency. Number range from=2 to=300<2-300>


Command Path:

# configure [['terminal', 't']](config)# mcp transmit-frequency <NUMBER>


M Commandsmcp transmit-frequency

membermember device <WORD> device-interface <WORD>

Description: Configure Cluster Interface Member

Syntax:

Cluster Devicedevice

Cluster Device name (Max Size 64)WORD

Cluster Device Interfacedevice-interface

Cluster Device Interface (Max Size 256)WORD

Command Mode: cluster-interface : Configure L4-L7 Cluster Interface

Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 cluster name <WORD> type <type> vlan-domain <domain-name> [service<service>] [function <function>](config-cluster)# cluster-interface <WORD> [vlan <NUMBER>](config-cluster-interface)# member device <WORD> device-interface <WORD>


M Commandsmember

message-levelmessage-level info|notice|emergency|alert|critical|error|debug|warning

Description: Configure the urgency of the message

Syntax:

Infoinfo

Noticenotice

Emergencyemergency

Alertalert

Criticalcritical

Errorerror

Debugdebug

Warningwarning


Command Path:

# configure [['terminal', 't']](config)# callhome common(config-callhome)# destination-profile(config-callhome-destnprof)# destination <WORD>(config-callhome-destnprof-destn)# message-levelinfo|notice|emergency|alert|critical|error|debug|warning


M Commandsmessage-level

message-sizemessage-size <NUMBER>

Description: configure the size of the message

Syntax:

The size of the messages. Number range from=0 to=5000000<size>


Command Path:

# configure [['terminal', 't']](config)# callhome common(config-callhome)# destination-profile(config-callhome-destnprof)# destination <WORD>(config-callhome-destnprof-destn)# message-size <NUMBER>


M Commandsmessage-size

metricmetric version 64bit

Description: Set EIGRP Metric Style

Syntax:

Metric Styleversion

wide metric64bit


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template eigrp vrf-policy <WORD> tenant <WORD>(config-template-eigrp-vrf-pol)# metric version 64bit

metric version 64bit

Description: Set EIGRP Metric Style

Syntax:

Metric Styleversion

wide metric64bit


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router eigrp default(config-eigrp)# vrf member tenant <WORD> vrf <WORD>(config-eigrp-vrf)# address-family ipv4|ipv6 unicast(config-address-family)# metric version 64bit


M Commandsmetric

mgmt-epgmgmt-epg in-band|out-of-band <WORD>

Description: Select remote path management EPG

Syntax:

In-Band EPGin-band

Out-of-Band EPGout-of-band

Management EPG nameWORD

Command Mode: remote : Remote path configuration mode

Command Path:

# configure [['terminal', 't']](config)# remote path <WORD>(config-remote)# mgmt-epg in-band|out-of-band <WORD>


M Commandsmgmt-epg

microsoft-domainmicrosoft-domain <WORD>

Description: Create a VMMMicrosoft Domain

Syntax:

VMMMicrosoft Domain nameWORD


Command Path:

# configure [['terminal', 't']](config)# microsoft-domain <WORD>

microsoft-domain member <WORD> [encap <WORD>] [deploy <WORD>] [push <WORD>]

Description: Associate EPG to a Microsoft Domain

Syntax:

Bind the EPG to a Microsoft domainmember

Microsoft Domain NameWORD

(Optional) Enforce encap value. (For example vlan-10 or auto)WORD

(Optional) Deployment modeWORD

(Optional) Push modeWORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# microsoft-domain member <WORD> [encap <WORD>] [deploy <WORD>] [push<WORD>]


M Commandsmicrosoft-domain

microsoftmicrosoft static-ip-pool <name> gateway <gwAddress>

Description: Configure static ip pool

Syntax:

Configure the static IP poolstatic-ip-pool

enter the name of the static IP poolname


gwAddressgwAddress


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# microsoft static-ip-pool <name> gateway <gwAddress>


M Commandsmicrosoft

min-rxmin-rx <NUMBER>

Description: Configure BFD MIN-RX value in milliseconds

Syntax:



Command Path:

# configure [['terminal', 't']](config)# template bfd ip|ipv6 <WORD>(config-bfd)# min-rx <NUMBER>

min-rx <NUMBER>

Description: Configure required Minimum Rx Interval in milliseconds

Syntax:

Minimum Rx Interval. Number range from=50 to=999<interval>


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template bfd <WORD> tenant <WORD>(config-template-bfd-pol)# min-rx <NUMBER>


M Commandsmin-rx

min-txmin-tx <NUMBER>

Description: Configure BFD MIN-TX value in milliseconds

Syntax:



Command Path:

# configure [['terminal', 't']](config)# template bfd ip|ipv6 <WORD>(config-bfd)# min-tx <NUMBER>

min-tx <NUMBER>

Description: Configure required Minimum Tx Interval in milliseconds

Syntax:

Minimum Tx Interval. Number range from=50 to=999<interval>


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template bfd <WORD> tenant <WORD>(config-template-bfd-pol)# min-tx <NUMBER>


M Commandsmin-tx

minmin buffer <0-3>

Description: Set the minimum number of buffer of MTU size to be reserved

Syntax:

Number of minim buffers to reservebuffer

Number of minim buffers to reserve<0-3>


Command Path:

# configure [['terminal', 't']](config)# qos parameters level1|level2|level3(config-qos)# min buffer <0-3>


M Commandsmin

modemode atomic|best-effort

Description: Snapshot import mode atomic|best-effort

Syntax:

Atomic modeatomic

Best Effort modebest-effort


Command Path:

# configure [['terminal', 't']](config)# snapshot import <WORD>(config-import)# mode atomic|best-effort


M Commandsmode

modulusmodulus <modulus>

Description: Set the length of the encryption keys

Syntax:

<modulus><modulus>


Command Path:

# configure [['terminal', 't']](config)# crypto keyring <WORD>(config-keyring)# modulus <modulus>


M Commandsmodulus

monitormonitor virtual session <WORD>

Description: Configure a monitor session

Syntax:

virtualvirtual

sessionsession

session name (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# vmware-domain <WORD>(config-vmware)# configure-avs(config-vmware-avs)# monitor virtual session <WORD>


M Commandsmonitor

monitor accessmonitor access session <session_name>

Description: Configue monitor session for access interfaces

Syntax:

sessionsession

session name (Max Size 64)session_name


Command Path:

# configure [['terminal', 't']](config)# monitor access session <session_name>


M Commandsmonitor access

monitor fabricmonitor fabric session <session_name>

Description: Configue monitor session for fabric interfaces

Syntax:

sessionsession



Command Path:

# configure [['terminal', 't']](config)# monitor fabric session <session_name>


M Commandsmonitor fabric

monitor tenantmonitor tenant <tenant_name> session <session_name>

Description: Configue monitor session for tenant EPGs

Syntax:


sessionsession



Command Path:

# configure [['terminal', 't']](config)# monitor tenant <tenant_name> session <session_name>


M Commandsmonitor tenant

monitor virtualmonitor virtual session <WORD>

Description: Configure monitor session for virtual switches

Syntax:

sessionsession

Session name (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# monitor virtual session <WORD>


M Commandsmonitor virtual

mtu-ignoremtu-ignore



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf interface-policy <WORD> tenant <WORD>(config-interface-policy)# mtu-ignore


M Commandsmtu-ignore

mtumtu <1500-9216>

Description: Set the MTU for this class of service

Syntax:

MTU value<1500-9216>


Command Path:

# configure [['terminal', 't']](config)# qos parameters level1|level2|level3(config-qos)# mtu <1500-9216>

mtu <NUMBER>

Description: Set the interface Maximum Transmission Unit (MTU)

Syntax:

Interface MTU. Number range from=576 to=9000<576-9000>


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# mtu <NUMBER>

mtu <NUMBER>

Description: Set the interface Maximum Transmission Unit (MTU)

Syntax:

Interface MTU. Number range from=576 to=9000<576-9000>


Command Path:



M Commandsmtu

(config-leaf-if)# mtu <NUMBER>

mtu <mtu>

Description:MTU size

Syntax:

mtu value. Number range from=64 to=9216mtu


Command Path:

# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# destination tenant <tenant_name> application <application_name>epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M>(config-monitor-access-dest)# mtu <mtu>

mtu <mtu>


Syntax:

mtu value. Number range from=64 to=9216mtu


Command Path:

# configure [['terminal', 't']](config)# monitor fabric session <session_name>(config-monitor-fabric)# destination tenant <tenant_name> application <application_name>epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M>(config-monitor-fabric-dest)# mtu <mtu>

mtu <arg>


Syntax:

mtu value. Number range from=64 to=9216arg


Command Path:

# configure [['terminal', 't']](config)# monitor tenant <tenant_name> session <session_name>(config-monitor-tenant)# destination tenant <tenant_name> application <application_name>epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M>


M Commandsmtu

(config-monitor-tenant-dest)# mtu <>

mtu <arg>

Description: Configure MTU size

Syntax:

MTU value. Number range from=64 to=9216arg


Command Path:

# configure [['terminal', 't']](config)# monitor virtual session <WORD>(config-monitor-virtual)# destination destip <A.B.C.D>(config-monitor-virtual-remote-dest)# mtu <>


M Commandsmtu

multi-destinationmulti-destination <WORD>

Description: Change behavior for multi destination flood

Syntax:

Unknown multicast MAC and Broadcast handlingWORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>(config-tenant-bd)# multi-destination <WORD>


M Commandsmulti-destination

multi-site-mac-addressmulti-site-mac-address E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE

Description: Configure multi-site MAC address

Syntax:






Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# multi-site-mac-addressE.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE


M Commandsmulti-site-mac-address

multicast-addressmulticast-address <IP>

Description: Configure outgoing multicast IP address for VXLAN modes

Syntax:

Multicast IPIP


Command Path:

# configure [['terminal', 't']](config)# vmware-domain <WORD>(config-vmware)# configure-avs(config-vmware-avs)# multicast-address <IP>


M Commandsmulticast-address

multipliermultiplier <NUMBER>

Description: Configure BFD MULTIPLIER value

Syntax:



Command Path:

# configure [['terminal', 't']](config)# template bfd ip|ipv6 <WORD>(config-bfd)# multiplier <NUMBER>

multiplier <NUMBER>

Description: Configure detection multiplier

Syntax:

Detection multiplier. Number range from=1 to=50<interval>


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template bfd <WORD> tenant <WORD>(config-template-bfd-pol)# multiplier <NUMBER>


M Commandsmultiplier

N Commands

• name-lookup, page 542

• negotiate, page 543

• neighbor, page 545

• network, page 546

• next-hop-self, page 547

• ntp, page 548


name-lookupname-lookup

Description: Display OSPF router ids as DNS names


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf vrf-policy <WORD> tenant <WORD>(config-vrf-policy)# name-lookup


N Commandsname-lookup

negotiatenegotiate auto

Description: Configure link negotiation parameters

Syntax:

Configure auto-negotiationauto


Command Path:

# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# negotiate auto

negotiate auto


Syntax:



Command Path:

# configure [['terminal', 't']](config)# template port-channel <WORD>(config-if)# negotiate auto

negotiate auto


Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# negotiate auto


N Commandsnegotiate

negotiate auto


Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# negotiate auto

negotiate auto


Syntax:



Command Path:

# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# negotiate auto


N Commandsnegotiate

neighborneighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [l3out <WORD>]

Description: Configure a BGP neighbor

Syntax:

IP address of the neighborA.B.C.D

IP prefix for neighborsA.B.C.D/LEN

IPv6 address of the neighborA:B::C:D

IPv6 prefix for neighborsA:B::C:D/LEN

(Optional) Route-Map Name (API-configured L3Out Name)WORD


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [l3out <WORD>]


N Commandsneighbor

networknetwork bcast|p2p|unspecified


Syntax:


bcast


p2p


unspecified


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf interface-policy <WORD> tenant <WORD>(config-interface-policy)# network bcast|p2p|unspecified


N Commandsnetwork

next-hop-selfnext-hop-self

Description: Set our peering address as nexthop


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [l3out <WORD>](config-leaf-bgp-vrf-neighbor)# next-hop-self


N Commandsnext-hop-self

ntpntp

Description: Configure the default ntp policy


Command Path:

# configure [['terminal', 't']](config)# pod 1(config-pod)# ntp


N Commandsntp

O Commands

• oob-mgmt, page 550

• oob-mgmt epg, page 551

• optimize, page 552

• option, page 553

• org-name, page 554

• org-unit-name, page 555


oob-mgmtoob-mgmt epg <epgval>

Description: Creates/Modify the out of band mgmt under the tenant mgmt

Syntax:

epg is keyword ,refers to out of band epgepg

epg name for the out of band epg created/modified under tenant mgmtepgval


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# oob-mgmt epg <epgval>


O Commandsoob-mgmt

oob-mgmt epgoob-mgmt epg <WORD>

Description: Associate node to a Out of band EPG

Syntax:

Out of band End Point Group NameWORD


Command Path:

# configure [['terminal', 't']](config)# controller(config-controller)# interface mgmt0(config-controller-if)# oob-mgmt epg <WORD>

oob-mgmt epg <WORD>

Description: Associate node to a Out of band EPG

Syntax:

Out of band End Point Group NameWORD


Command Path:

# configure [['terminal', 't']](config)# switch(config-switch)# interface mgmt0(config-switch-if)# oob-mgmt epg <WORD>


O Commandsoob-mgmt epg

optimizeoptimize subinterface

Description: Disable sub-interface optimization

Syntax:

subinterfacesubinterface


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template bfd <WORD> tenant <WORD>(config-template-bfd-pol)# optimize subinterface


O Commandsoptimize

optionoption <WORD> id <NUMBER> data <WORD>

Description: Add or modify an existing DHCP option when relayed from the server to the client

Syntax:

Name of the option to add (Max Size 64)WORD

ID of the optionid

ID of the option. Number range from=0 to=255<0-255>

Body of the Option TLV as hex stringdata

Body of the Option TLV as hex string, surrounded by single quotes ex:'foo*' (Max Size 256)

WORD

Command Mode: template dhcp option : Create a DHCP Option policy

Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template dhcp option policy <WORD>(config-tenant-template-dhcp-option)# option <WORD> id <NUMBER> data <WORD>


O Commandsoption

org-nameorg-name <WORD>

Description: Set The full legal name of the organization.

Syntax:

legal name of organization (Max Size 64)<WORD>


Command Path:

# configure [['terminal', 't']](config)# crypto keyring <WORD>(config-keyring)# csr(config-csr)# org-name <WORD>


O Commandsorg-name

org-unit-nameorg-unit-name <WORD>

Description: Set the department or unit name within the organization

Syntax:

department or unit name (Max Size 64)<WORD>


Command Path:

# configure [['terminal', 't']](config)# crypto keyring <WORD>(config-keyring)# csr(config-csr)# org-unit-name <WORD>


O Commandsorg-unit-name


O Commandsorg-unit-name

P Commands

• passive-interface, page 559

• passphrase, page 560

• password, page 561

• password change-count, page 563

• password change-during-interval, page 564

• password change-interval, page 565

• password history-count, page 566

• password no-change-interval, page 567

• password pwd-strength-check, page 568

• path, page 569

• peer-dead-interval, page 570

• periodic-inventory notification, page 571

• phone-contact, page 572

• phone, page 573

• pod, page 574

• policy-group, page 575

• policy-map, page 577

• policy-map type data-plane, page 578

• policy-map type qos, page 579

• port, page 580

• porttrack delay, page 583

• porttrack minlinks, page 584

• porttrack state, page 585

• power, page 586


• prefix-suppression, page 587

• preview, page 588

• priority, page 589

• priv-type, page 590

• priv, page 591

• private-as-control, page 592

• protocol, page 593

• pwd-lifetime, page 594


P Commands

passive-interfacepassive-interface



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf interface-policy <WORD> tenant <WORD>(config-interface-policy)# passive-interface


P Commandspassive-interface

passphrasepassphrase <WORD>

Description: Configure passphrase for AES encryption

Syntax:

Passphrase for AES encryption (Range of chars: 16-32) in quotes (MaxSize 32)

WORD


Command Path:

# configure [['terminal', 't']](config)# crypto aes(config-aes)# passphrase <WORD>


P Commandspassphrase

passwordpassword <WORD>

Description: Set The system user password.

Syntax:

Change user password (Max Size 256) - Only for admin useWORD


Command Path:

# configure [['terminal', 't']](config)# username <WORD>(config-username)# password <WORD>

password <WORD>

Description: Set The new password.

Syntax:

new password<WORD>


Command Path:

# configure [['terminal', 't']](config)# crypto keyring <WORD>(config-keyring)# csr(config-csr)# password <WORD>

password WORD

Description: Configure a password for neighbor

Syntax:

Enter Clear-text passwordWORD


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>


P Commandspassword

(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [l3out <WORD>](config-leaf-bgp-vrf-neighbor)# password WORD


P Commandspassword

password change-countpassword change-count <NUMBER>

Description: Set the number of password changes allowed within change interval

Syntax:

Set the number of password changes allowed within change interval.Number range from=0 to=10

<0-10>


Command Path:

# configure [['terminal', 't']](config)# password change-count <NUMBER>


P Commandspassword change-count

password change-during-intervalpassword change-during-interval <change-during-interval>

Description: Set change count/interval policy selector for enforcing password change.

Syntax:

<change-during-interval><change-during-interval>


Command Path:

# configure [['terminal', 't']](config)# password change-during-interval <change-during-interval>


P Commandspassword change-during-interval

password change-intervalpassword change-interval <NUMBER>

Description: Set time interval for limiting the number of password changes (unit: Hours)

Syntax:

Set A time interval for limiting the number of password changes (unit:Hours). Number range from=1 to=745

<1-745>


Command Path:

# configure [['terminal', 't']](config)# password change-interval <NUMBER>


P Commandspassword change-interval

password history-countpassword history-count <NUMBER>

Description: Set number of retired passwords to store in user's history.

Syntax:

Set number of retired passwords to store in user history.. Number rangefrom=0 to=15

<0-15>


Command Path:

# configure [['terminal', 't']](config)# password history-count <NUMBER>


P Commandspassword history-count

password no-change-intervalpassword no-change-interval <NUMBER>

Description: Set minimum period before which user cannot change password again (unit: hours)

Syntax:

Set minimum period before which user cannot change password again(unit: hours). Number range from=1 to=745

<1-745>


Command Path:

# configure [['terminal', 't']](config)# password no-change-interval <NUMBER>


P Commandspassword no-change-interval

password pwd-strength-checkpassword pwd-strength-check

Description: Enforces the strength of password for all users


Command Path:

# configure [['terminal', 't']](config)# password pwd-strength-check


P Commandspassword pwd-strength-check

pathpath ftp|sftp|scp <HOST> [port <NUMBER>] [remote-directory <PATH>]

Description: Configure remote path properties

Syntax:

FTPftp

Secure FTPsftp

Secure copyscp

Remote host name or IP addressHOST

(Optional) Remote port. Number range from=0 to=65535<0-65535>

(Optional) Remote directory: path/to/some/dirPATH


Command Path:

# configure [['terminal', 't']](config)# remote path <WORD>(config-remote)# path ftp|sftp|scp <HOST> [port <NUMBER>] [remote-directory <PATH>]


P Commandspath

peer-dead-intervalpeer-dead-interval <NUMBER>

Description: Configure Peer dead Interval

Syntax:

Peer dead Interval value. Number range from=5 to=600<5-600>

Command Mode: vpc domain explicit : Pair two leaf nodes explicitly

Command Path:

# configure [['terminal', 't']](config)# vpc domain explicit <NUMBER> leaf <101-4000> <101-4000>(config-vpc)# peer-dead-interval <NUMBER>


P Commandspeer-dead-interval

periodic-inventory notificationperiodic-inventory notification schedule <schedName>

Description: Configure periodic notifications Parameters

Syntax:

Configure periodic notification schedulerschedule

scheduler name<schedName>


Command Path:

# configure [['terminal', 't']](config)# callhome common(config-callhome)# periodic-inventory notification schedule <schedName>


P Commandsperiodic-inventory notification

phone-contactphone-contact <WORD>

Description: The contact phone number

Syntax:

Phone number in international format(such as +1-800-123-4567) (MaxSize 512)

WORD


Command Path:

# configure [['terminal', 't']](config)# callhome common(config-callhome)# destination-profile(config-callhome-destnprof)# phone-contact <WORD>


P Commandsphone-contact

phonephone <WORD>

Description: Set The phone number of the locally-authenticated user.

Syntax:

phone number (Max Size 512)WORD


Command Path:

# configure [['terminal', 't']](config)# username <WORD>(config-username)# phone <WORD>


P Commandsphone

podpod 1

Description: Pod configuration mode

Syntax:

Enter Pod ID1


Command Path:

# configure [['terminal', 't']](config)# pod 1


P Commandspod

policy-grouppolicy-group <WORD>

Description: Associate an Interface Policy Group to this Interface Group

Syntax:

Interface Policy Group Name (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# leaf-interface-profile <WORD>(config-leaf-if-profile)# leaf-interface-group <WORD>(config-leaf-if-group)# policy-group <WORD>

policy-group <WORD>

Description: Configure Policy Group on the Fex

Syntax:



Command Path:

# configure [['terminal', 't']](config)# fex-profile <WORD>(config-fex-profile)# fex-interface-group <WORD>(config-fex-if-group)# policy-group <WORD>

policy-group <WORD> [force]

Description: Configure Policy Group

Syntax:


(Optional) Delete Per Port Configuration and apply the existingpolicy-group config

force



P Commandspolicy-group

Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# policy-group <WORD> [force]


P Commandspolicy-group

policy-mappolicy-map type data-plane <WORD>

Description: Create a policymap of DataPlane type to police/reclassify the traffic

Syntax:

Type of the Qos Policytype

QOS policy for Data Plane Policingdata-plane

Name of the policy-map to add (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>


P Commandspolicy-map

policy-map type data-planepolicy-map type data-plane <WORD>

Description: data-plane policy type

Syntax:

Policy Typetype



Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>


P Commandspolicy-map type data-plane

policy-map type qospolicy-map type qos <WORD>

Description: QOS policy type

Syntax:

Policy Typetype



Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type qos <WORD>


P Commandspolicy-map type qos

portport <NUMBER>

Description: LDAP server port for authentication

Syntax:

Port number. Number range from=1 to=65535<1-65535>


Command Path:

# configure [['terminal', 't']](config)# ldap-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# port <NUMBER>

port <NUMBER>

Description: RADIUS server port for authentication

Syntax:

RADIUS server port for authentication. Number range from=1 to=65535<1-65535>


Command Path:

# configure [['terminal', 't']](config)# radius-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# port <NUMBER>

port <NUMBER>

Description: TACACS server port for authentication

Syntax:

RADIUS server port for authentication. Number range from=1 to=65535<1-65535>


Command Path:

# configure [['terminal', 't']](config)# tacacs-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# port <NUMBER>


P Commandsport

port <NUMBER>

Description: Set the port used for SSH communication service.

Syntax:

Set the port used for SSH communication service.. Number rangefrom=0 to=65535

<0-65535>

Command Mode: ssh-service : SSH communication policy group

Command Path:

# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# ssh-service(config-ssh-service)# port <NUMBER>

port <NUMBER>

Description: Set the port used for TELNET communication service.

Syntax:

Set the port used for TELNET communication service.. Number rangefrom=0 to=65535

<0-65535>

Command Mode: telnet : TELNET communication policy group

Command Path:

# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# telnet(config-telnet)# port <NUMBER>

port <NUMBER>

Description: Set the port used for HTTP communication service.

Syntax:

Set the port used for HTTP communication service.. Number rangefrom=1 to=65535

<1-65535>


Command Path:

# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# http(config-http)# port <NUMBER>


P Commandsport

port <NUMBER>

Description: Set the port used for HTTPS communication service

Syntax:

Set the port used for HTTPS communication service. Number rangefrom=1 to=65535

<1-65535>


Command Path:

# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# https(config-https)# port <NUMBER>


P Commandsport

porttrack delayporttrack delay <1-300>

Description: Set Port Tracking Delay

Syntax:

Delay value<1-300>


Command Path:

# configure [['terminal', 't']](config)# porttrack delay <1-300>


P Commandsporttrack delay

porttrack minlinksporttrack minlinks <0-12>

Description: Set Port Tracking minimum links left up before trigger

Syntax:

Minlinks Value<0-12>


Command Path:

# configure [['terminal', 't']](config)# porttrack minlinks <0-12>


P Commandsporttrack minlinks

porttrack stateporttrack state on

Description: Set Port Tracking State

Syntax:

To enable port tracking stateon


Command Path:

# configure [['terminal', 't']](config)# porttrack state on


P Commandsporttrack state

powerpower redundancy-policy <WORD>

Description: Create a power supply redundancy policy

Syntax:

Create a power supply redundancy policyredundancy-policy

Power supply redundancy policy name (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# power redundancy-policy <WORD>


P Commandspower

prefix-suppressionprefix-suppression

Description: Suppress prefixes


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf vrf-policy <WORD> tenant <WORD>(config-vrf-policy)# prefix-suppression


P Commandsprefix-suppression

previewpreview

Description: Rollback preview mode


Command Path:

# configure [['terminal', 't']](config)# snapshot rollback <WORD>(config-rollback)# preview


P Commandspreview

prioritypriority <NUMBER>


Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf interface-policy <WORD> tenant <WORD>(config-interface-policy)# priority <NUMBER>


P Commandspriority

priv-typepriv-type <privType>

Description: Set the AAA domain role to set privilege bitmask of a user domain

Syntax:

<privType><privType>

Command Mode: role : Create the AAA domain role to set privilege bitmask of a user domain

Command Path:

# configure [['terminal', 't']](config)# username <WORD>(config-username)# domain <WORD>(config-domain)# role <WORD>(config-role)# priv-type <privType>


P Commandspriv-type

privpriv <privileges>

Description: Set privileges (comma separated values)

Syntax:

Privileges as comma separated values like val1,val2,..valN<privileges>

Command Mode: rbac role : Create AAA role, attributes and privileges for user authorization

Command Path:

# configure [['terminal', 't']](config)# rbac role <WORD>(config-role)# priv <privileges>


P Commandspriv

private-as-controlprivate-as-control remove-exclusive|remove-exclusive-all|remove-exclusive-all-replace-as

Description: Private AS Control

Syntax:

Remove private ASremove-exclusive

Remove all private ASremove-exclusive-all

Replace private AS with local ASremove-exclusive-all-replace-as


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [l3out <WORD>](config-leaf-bgp-vrf-neighbor)# private-as-controlremove-exclusive|remove-exclusive-all|remove-exclusive-all-replace-as


P Commandsprivate-as-control

protocolprotocol <protocol>

Description: RADIUS server protocol for authentication

Syntax:

<protocol><protocol>


Command Path:

# configure [['terminal', 't']](config)# radius-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# protocol <protocol>

protocol <WORD>

Description: Set the TACACS+ authentication protocol

Syntax:

TACACS+ authentication protocolWORD


Command Path:

# configure [['terminal', 't']](config)# tacacs-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# protocol <WORD>


P Commandsprotocol

pwd-lifetimepwd-lifetime <NUMBER>

Description: Set The lifetime of the user password (0 = No password expiration)

Syntax:

lifetime of locally-authenticated user password. Number range from=0to=3650

<0-3650>


Command Path:

# configure [['terminal', 't']](config)# username <WORD>(config-username)# pwd-lifetime <NUMBER>


P Commandspwd-lifetime

Q Commands

• qos parameters, page 596

• qos preserve, page 597

• query-cluster-health, page 598

• query-cluster-statistics, page 599

• query-cluster-validation, page 600

• query-profile, page 601

• query, page 602

• queue control, page 603

• queue limit, page 604


qos parametersqos parameters level1|level2|level3

Description: Configure the global QOS policies

Syntax:

Set parameters for level1level1




Command Path:

# configure [['terminal', 't']](config)# qos parameters level1|level2|level3


Q Commandsqos parameters

qos preserveqos preserve cos

Description: Preserve incoming qos value in the frame

Syntax:

IEEE 802.1P class of service.cos


Command Path:

# configure [['terminal', 't']](config)# qos preserve cos


Q Commandsqos preserve

query-cluster-healthquery-cluster-health

Description: Re-query for Cluster Health


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 cluster name <WORD> type <type> vlan-domain <domain-name> [service<service>] [function <function>](config-cluster)# query-cluster-health


Q Commandsquery-cluster-health

query-cluster-statisticsquery-cluster-statistics

Description: Re-query for Cluster Statistics


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 cluster name <WORD> type <type> vlan-domain <domain-name> [service<service>] [function <function>](config-cluster)# query-cluster-statistics


Q Commandsquery-cluster-statistics

query-cluster-validationquery-cluster-validation

Description: Re-query for Cluster Validation


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 cluster name <WORD> type <type> vlan-domain <domain-name> [service<service>] [function <function>](config-cluster)# query-cluster-validation


Q Commandsquery-cluster-validation

query-profilequery-profile

Description: Configure Query profile Parameters


Command Path:

# configure [['terminal', 't']](config)# callhome common(config-callhome)# query-profile


Q Commandsquery-profile

queryquery <WORD> type dn|class <dn/classname>

Description: Configure Query profile Parameters

Syntax:

Query name (Max Size 16)WORD

typetype

Dndn

Classclass

The class or DN name<dn/classname>

Command Mode: query-profile : Configure Query profile Parameters

Command Path:

# configure [['terminal', 't']](config)# callhome common(config-callhome)# query-profile(config-callhome-queryprof)# query <WORD> type dn|class <dn/classname>


Q Commandsquery

queue controlqueue control dynamic

Description: Set the queueing control method

Syntax:

Dynamic allocation of queue resourcesdynamic


Command Path:

# configure [['terminal', 't']](config)# qos parameters level1|level2|level3(config-qos)# queue control dynamic


Q Commandsqueue control

queue limitqueue limit <1500-9216>

Description: Set the limit for the policing queue

Syntax:

Queue limit size<1500-9216>


Command Path:

# configure [['terminal', 't']](config)# qos parameters level1|level2|level3(config-qos)# queue limit <1500-9216>


Q Commandsqueue limit

R Commands

• radius-server host, page 607

• radius-server retries, page 608

• radius-server timeout, page 609

• rbac role, page 610

• rbac rule, page 611

• rbac security-domain, page 612

• realm, page 613

• recurring, page 614

• redirect, page 615

• redistribute, page 616

• redundancy-mode, page 617

• region, page 618

• reload controller, page 619

• reload switch, page 620

• remote-as, page 621

• remote, page 622

• request-status-count, page 624

• reset-to-factory, page 625

• response-incl, page 626

• response-subtree, page 627

• retransmit-interval, page 628

• retries, page 629

• revision, page 630

• role, page 631


• route-map, page 632

• route-profile, page 633

• route-reflector, page 634

• router-id, page 635

• router bgp, page 636

• router eigrp, page 637

• router ospf, page 638

• rtr-cfg, page 639

• run-mode, page 640


R Commands

radius-server hostradius-server host <A.B.C.D|A:B::C:D|WORD>

Description: RADIUS server's DNS name or its IP address

Syntax:

Provide a hostname or IPV4/IPV6 addressA.B.C.D|A:B::C:D|WORD


Command Path:

# configure [['terminal', 't']](config)# radius-server host <A.B.C.D|A:B::C:D|WORD>


R Commandsradius-server host

radius-server retriesradius-server retries <NUMBER>

Description: Global RADIUS server retransmit count

Syntax:

Global RADIUS server retransmit count. Number range from=0 to=5<0-5>


Command Path:

# configure [['terminal', 't']](config)# radius-server retries <NUMBER>


R Commandsradius-server retries

radius-server timeoutradius-server timeout <NUMBER>

Description: Global RADIUS server timeout period in seconds

Syntax:

Global RADIUS server timeout period in seconds. Number range from=1to=60

<1-60>


Command Path:

# configure [['terminal', 't']](config)# radius-server timeout <NUMBER>


R Commandsradius-server timeout

rbac rolerbac role <WORD>

Description: Create AAA role, attributes and privileges for user authorization

Syntax:

Provide AAA Security domain role name (Max Size 32)WORD


Command Path:

# configure [['terminal', 't']](config)# rbac role <WORD>


R Commandsrbac role

rbac rulerbac rule <DN> <WORD>

Description: Create RBAC rule, security domain users can read subtree starting at specific object

Syntax:

Provide RBAC Rule ObjectDN stringDN

Provide RBAC Rule domain name (Max Size None)WORD


Command Path:

# configure [['terminal', 't']](config)# rbac rule <DN> <WORD>


R Commandsrbac rule

rbac security-domainrbac security-domain <WORD>

Description: Create AAA security domain for processing authentication requests.

Syntax:

Provide AAA Security domain name (Max Size 32)WORD


Command Path:

# configure [['terminal', 't']](config)# rbac security-domain <WORD>


R Commandsrbac security-domain

realmrealm <realm>

Description: Specify server realm

Syntax:

<realm><realm>

Command Mode: aaa authentication login console : Configure console methods

Command Path:

# configure [['terminal', 't']](config)# aaa authentication login console(config-console)# realm <realm>

realm <realm>


Syntax:

<realm><realm>

Command Mode: aaa authentication login default : Configure default methods

Command Path:

# configure [['terminal', 't']](config)# aaa authentication login default(config-default)# realm <realm>

realm <realm>


Syntax:

<realm><realm>

Command Mode: aaa authentication login domain : Configure domain methods

Command Path:

# configure [['terminal', 't']](config)# aaa authentication login domain <WORD>(config-domain)# realm <realm>


R Commandsrealm

recurringrecurring window <WORD>

Description: Recurring window configuration mode

Syntax:

Configure a schedule windowwindow

Window name (Max size 31)WORD


Command Path:

# configure [['terminal', 't']](config)# scheduler fabric|controller schedule <WORD>(config-scheduler)# recurring window <WORD>


R Commandsrecurring

redirectredirect

Description: Enable the state of the HTTP redirect state


Command Path:

# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# http(config-http)# redirect


R Commandsredirect

redistributeredistribute ospf|eigrp route-map <WORD>

Description: Redistribute route map

Syntax:

Redistribute OSPFospf

Redistribute EIGRPeigrp

Route map to redistribute toroute-map

Route map nameWORD


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# redistribute ospf|eigrp route-map <WORD>


R Commandsredistribute

redundancy-moderedundancy-mode combined|ps-redundant|redundant

Description: Configure power supply redundancy mode

Syntax:

Combined mode to use output of all available PScombined

PS redundant mode (N+1) to enable power output redundancyps-redundant

Redundant mode (N+N) for a single PS to power the systemredundant

Command Mode: power : Create a power supply redundancy policy

Command Path:

# configure [['terminal', 't']](config)# power redundancy-policy <WORD>(config-power)# redundancy-mode combined|ps-redundant|redundant


R Commandsredundancy-mode

regionregion <WORD>

Description: STP MST region configuration mode

Syntax:

MST region nameWORD

Command Mode: spanning-tree : STP MST configuration mode

Command Path:

# configure [['terminal', 't']](config)# spanning-tree mst configuration(config-stp)# region <WORD>


R Commandsregion

reload controllerreload controller <NUMBER>

Description: Reload controller

Syntax:



Command Path:

# reload controller <NUMBER>


R Commandsreload controller

reload switchreload switch <NUMBER>

Description: Reload switch

Syntax:

Switch id. Number range from=101 to=4000<101-4000>


Command Path:

# reload switch <NUMBER>


R Commandsreload switch

remote-asremote-as <NUMBER>

Description: Specify Autonomous System Number of the neighbor

Syntax:

The Remote autonomous system number. Number range from=1to=4294967295

<1-4294967295>


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [l3out <WORD>](config-leaf-bgp-vrf-neighbor)# remote-as <NUMBER>


R Commandsremote-as

remoteremote path <WORD>

Description: Remote path configuration mode

Syntax:

Configure remote pathpath

Remote path configuration nameWORD


Command Path:

# configure [['terminal', 't']](config)# remote path <WORD>

remote path <WORD>

Description: Set the remote path configuration will get downloaded from

Syntax:

Assign remote pathpath

Remote path nameWORD

Command Mode: snapshot download : Configuration snapshot download setup mode

Command Path:

# configure [['terminal', 't']](config)# snapshot download <WORD>(config-download)# remote path <WORD>

remote path <WORD>

Description: Set the remote path configuration will get exported to

Syntax:

Configure remote pathpath




R Commandsremote

Command Path:

# configure [['terminal', 't']](config)# snapshot export <WORD>(config-export)# remote path <WORD>

remote path <WORD>

Description: Set the remote path configuration will get imported from

Syntax:




Command Path:

# configure [['terminal', 't']](config)# snapshot import <WORD>(config-import)# remote path <WORD>

remote path <WORD>

Description: Set the remote path configuration will get uploaded to

Syntax:



Command Mode: snapshot upload : Configuration snapshot upload setup mode

Command Path:

# configure [['terminal', 't']](config)# snapshot upload <WORD>(config-upload)# remote path <WORD>


R Commandsremote

request-status-countrequest-status-count <NUMBER>

Description: Set the maximum count of HTTP requests to track.

Syntax:

Set the maximum count of HTTP requests to track.. Number rangefrom=0 to=10240

<count>


Command Path:

# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# http(config-http)# request-status-count <NUMBER>

request-status-count <NUMBER>

Description: Set the maximum count of HTTPS requests to track

Syntax:

Set the maximum count of HTTPS requests to track.. Number rangefrom=0 to=10240

<count>


Command Path:

# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# https(config-https)# request-status-count <NUMBER>


R Commandsrequest-status-count

reset-to-factoryreset-to-factory

Description: Reset role to factory default privileges

Command Mode: rbac role : Create AAA role, attributes and privileges for user authorization

Command Path:

# configure [['terminal', 't']](config)# rbac role <WORD>(config-role)# reset-to-factory


R Commandsreset-to-factory

response-inclresponse-incl <respincl>

Description: Configure response subtree which needs to be included

Syntax:

The response subtree to be included<respincl>

Command Mode: query : Configure Query profile Parameters

Command Path:

# configure [['terminal', 't']](config)# callhome common(config-callhome)# query-profile(config-callhome-queryprof)# query <WORD> type dn|class <dn/classname>(config-callhome-queryprof-query)# response-incl <respincl>


R Commandsresponse-incl

response-subtreeresponse-subtree full|children|no

Description: Configure response-subtree

Syntax:

Fullfull

Childrenchildren

Nono


Command Path:

# configure [['terminal', 't']](config)# callhome common(config-callhome)# query-profile(config-callhome-queryprof)# query <WORD> type dn|class <dn/classname>(config-callhome-queryprof-query)# response-subtree full|children|no


R Commandsresponse-subtree

retransmit-intervalretransmit-interval <NUMBER>

Description: Set the interval between LSA retransmissions

Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf interface-policy <WORD> tenant <WORD>(config-interface-policy)# retransmit-interval <NUMBER>


R Commandsretransmit-interval

retriesretries <NUMBER>

Description: LDAP server retries for authentication

Syntax:

LDAP server retries for authentication. Number range from=0 to=5<0-5>


Command Path:

# configure [['terminal', 't']](config)# ldap-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# retries <NUMBER>

retries <0-5>

Description: RADIUS server retries for authentication

Syntax:

RADIUS server retries for authentication<0-5>


Command Path:

# configure [['terminal', 't']](config)# radius-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# retries <0-5>

retries <NUMBER>

Description: TACACS server retries for authentication

Syntax:

TACACS server retries for authentication. Number range from=0 to=5<0-5>


Command Path:

# configure [['terminal', 't']](config)# tacacs-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# retries <NUMBER>


R Commandsretries

revisionrevision <NUMBER>

Description: Set the MST region revision number

Syntax:

MST region revision number. Number range from=0 to=65535<0-65535>


Command Path:

# configure [['terminal', 't']](config)# spanning-tree mst configuration(config-stp)# region <WORD>(config-stp-region)# revision <NUMBER>


R Commandsrevision

rolerole <WORD>

Description: Create the AAA domain role to set privilege bitmask of a user domain

Syntax:

User roleWORD

Command Mode: domain : Create the AAA domain to which the user belongs.

Command Path:

# configure [['terminal', 't']](config)# username <WORD>(config-username)# domain <WORD>(config-domain)# role <WORD>


R Commandsrole

route-maproute-map <WORD>

Description: Create route-map or enter route-map command mode

Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>

route-map <WORD> in|out

Description: Apply route-map to neighbor

Syntax:


Apply policy to incoming routesin

Apply policy to outgoing routesout


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [l3out <WORD>](config-leaf-bgp-vrf-neighbor)# route-map <WORD> in|out


R Commandsroute-map

route-profileroute-profile <WORD>

Description: Configure route-profile

Syntax:



Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# route-profile <WORD>

route-profile <WORD>

Description: Configure route-profile for bridge-domain

Syntax:



Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# route-profile <WORD>


R Commandsroute-profile

route-reflectorroute-reflector spine <LIST> [description <TEXT>]

Description: Configure BGP route-reflectors

Syntax:

Configure Spines as route-reflectorsspine

Route-reflector spine node name or ID list. Ex. spine1 or 103,105LIST

(Optional) DescriptionTEXT

Command Mode: bgp : Border Gateway Protocol (BGP)

Command Path:

# configure [['terminal', 't']](config)# pod 1(config-pod)# bgp fabric(config-pod-bgp)# route-reflector spine <LIST> [description <TEXT>]


R Commandsroute-reflector

router-idrouter-id <A.B.C.D|A:B::C:D>

Description: Set router-id for peer l4l7 device

Syntax:

IP address for the l4l7 peerA.B.C.D|A:B::C:D

Command Mode: rtr-cfg : Configure l4l7 router configuration parameters

Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# rtr-cfg <WORD>(rtr-cfg)# router-id <A.B.C.D|A:B::C:D>

router-id <A.B.C.D>

Description: Configure Router ID

Syntax:

Router ID ValueA.B.C.D


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# router-id <A.B.C.D>


R Commandsrouter-id

router bgprouter bgp <fabric-ASN>

Description: Border Gateway Protocol (BGP)

Syntax:

Autonomous System Number<fabric-ASN>


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>


R Commandsrouter bgp

router eigrprouter eigrp default

Description: Enhanced Interior Gateway Routing Protocol (EIGRP)

Syntax:

EIGRP process tagdefault


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router eigrp default


R Commandsrouter eigrp

router ospfrouter ospf default

Description: Open Shortest Path First (OSPF and OSPF Version3)

Syntax:

Process tag for ospf and ospfv3default


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router ospf default


R Commandsrouter ospf

rtr-cfgrtr-cfg <WORD>

Description: Configure router configuration association for a l4l7 service.

Syntax:

router configuration name (Max Size 64)WORD

Command Mode: service : Configure L4-L7 Service

Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 graph <WORD> [contract <contract-option>](config-graph)# service <WORD> [device-cluster-tenant <WORD>] [device-cluster <WORD>] [mode<Available Modes>](config-service)# rtr-cfg <WORD>

rtr-cfg <WORD>

Description: Configure l4l7 router configuration parameters

Syntax:

router configuration name (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# rtr-cfg <WORD>


R Commandsrtr-cfg

run-moderun-mode pause-never|pause-on-failure

Description: Set run-mode

Syntax:

Do not pause on failurepause-never

Pause upgrade if upgrade of current set of nodes failpause-on-failure


Command Path:

# configure [['terminal', 't']](config)# firmware(config-firmware)# switch-group <WORD>(config-firmware-switch)# run-mode pause-never|pause-on-failure


R Commandsrun-mode

S Commands

• schedule, page 661

• scheduler, page 662

• scheduling, page 663

• scope, page 664

• scvmm, page 665

• second-file, page 666

• security-domain, page 667

• security, page 668

• send-community, page 669

• server, page 670

• service-policy, page 673

• service, page 676

• session-record-flags, page 677

• set, page 678

• set burst, page 680

• set cir, page 681

• set community, page 682

• set conform-cos-transmit, page 685

• set conform-dscp-transmit, page 686

• set conform, page 687

• set dampening, page 688

• set dscp, page 689

• set exceed-cos-transmit, page 690

• set exceed-dscp-transmit, page 691


• set exceed, page 692

• set excessive-burst, page 693

• set local-preference, page 694

• set metric-type, page 696

• set metric, page 698

• set mode, page 700

• set pir, page 701

• set qos-class, page 702

• set tag, page 703

• set target-dscp, page 705

• set type, page 706

• set violate-cos-transmit, page 707

• set violate-dscp-transmit, page 708

• set violate, page 709

• set weight, page 710

• shellinabox, page 712

• show aaa authentication, page 713

• show aaa groups, page 714

• show access-list, page 715

• show accounting log, page 716

• show application, page 717

• show audits, page 718

• show audits tenant, page 719

• show audits tenant application, page 720

• show audits tenant application epg, page 721

• show audits tenant bridge-domain, page 722

• show audits tenant bridge-domain detail, page 723

• show audits tenant interface bridge-domain, page 724

• show audits tenant interface bridge-domain detail, page 725

• show audits tenant vrf, page 726

• show audits tenant vrf detail, page 727

• show audits tenant vrf external-l3 bgp, page 728

• show audits tenant vrf external-l3 bgp node, page 729


S Commands

• show audits tenant vrf external-l3 eigrp, page 730

• show audits tenant vrf external-l3 eigrp detail, page 731

• show audits tenant vrf external-l3 epg, page 732

• show audits tenant vrf external-l3 epg detail, page 733

• show audits tenant vrf external-l3 epg name, page 734

• show audits tenant vrf external-l3 epg name detail, page 735

• show audits tenant vrf external-l3 interfaces, page 736

• show audits tenant vrf external-l3 interfaces detail, page 737

• show audits tenant vrf external-l3 ospf, page 738

• show audits tenant vrf external-l3 ospf detail, page 739

• show audits tenant vrf external-l3 static-route, page 740

• show audits tenant vrf external-l3 static-route detail, page 741

• show audits tenant vrf external-l3 static-route node, page 742

• show audits tenant vrf external-l3 static-route node detail, page 743

• show bridge-domain, page 744

• show bridge-domain detail, page 745

• show callhome, page 746

• show callhome common destination-profile, page 747

• show callhome common query-profile, page 748

• show callhome common transport-email, page 749

• show catalog, page 750

• show cli command, page 751

• show cli internal audit, page 752

• show cli internal transaction, page 753

• show cli list, page 754

• show cli manpage, page 755

• show cli path, page 756

• show clock, page 757

• show communication ciphers, page 758

• show communication http, page 759

• show communication https, page 760

• show communication shellinabox, page 761

• show communication ssh-service, page 762


S Commands

• show communication telnet, page 763

• show communication web-requests, page 764

• show contract-type, page 765

• show contract, page 766

• show controller, page 767

• show controller detail, page 768

• show cores, page 769

• show debug counter, page 770

• show debug log, page 771

• show dns-address, page 772

• show dns-domain, page 773

• show endpoints, page 774

• show endpoints leaf interface ethernet, page 775

• show endpoints leaf interface port-channel, page 776

• show endpoints vpc, page 777

• show epg, page 778

• show epg detail, page 779

• show events, page 780

• show events controller, page 781

• show events controller detail, page 782

• show events leaf, page 783

• show events leaf fex, page 784

• show events leaf fex module, page 785

• show events leaf interface ethernet, page 786

• show events leaf interface l3instance, page 787

• show events leaf interface mgmt, page 788

• show events leaf interface portchannel, page 789

• show events leaf interface tunnel, page 790

• show events leaf inventory chassis, page 791

• show events leaf inventory fans, page 792

• show events leaf inventory module, page 793

• show events leaf inventory module fabricport, page 794

• show events leaf inventory module leafport, page 795


S Commands

• show events leaf inventory powersupply, page 796

• show events leaf inventory supervisor, page 797

• show events leaf protocol, page 798

• show events leaf vpc, page 799

• show events leaf vrf, page 800

• show events spine, page 801

• show events spine interface ethernet, page 802

• show events spine interface l3instance, page 803

• show events spine interface mgmt, page 804

• show events spine interface tunnel, page 805

• show events spine inventory chassis, page 806

• show events spine inventory fabric, page 807

• show events spine inventory fans, page 808

• show events spine inventory module, page 809

• show events spine inventory module fabricport, page 810

• show events spine inventory powersupply, page 811

• show events spine inventory supervisor, page 812

• show events spine inventory system, page 813

• show events spine protocol, page 814

• show events spine vrf, page 815

• show events tenant, page 816

• show events tenant application, page 817

• show events tenant application epg, page 818

• show events tenant bridge-domain, page 819

• show events tenant bridge-domain detail, page 820

• show events tenant endpoints, page 821

• show events tenant endpoints leaf interface ethernet, page 822

• show events tenant endpoints leaf interface port-channel, page 823

• show events tenant endpoints vpc, page 824

• show events tenant interface bridge-domain, page 826

• show events tenant interface bridge-domain detail, page 827

• show events tenant vrf, page 828

• show events tenant vrf detail, page 829


S Commands

• show events tenant vrf external-l3 bgp, page 830

• show events tenant vrf external-l3 bgp node, page 831

• show events tenant vrf external-l3 eigrp, page 832

• show events tenant vrf external-l3 eigrp detail, page 833

• show events tenant vrf external-l3 epg, page 834

• show events tenant vrf external-l3 epg detail, page 835

• show events tenant vrf external-l3 epg name, page 836

• show events tenant vrf external-l3 epg name detail, page 837

• show events tenant vrf external-l3 interfaces, page 838

• show events tenant vrf external-l3 interfaces detail, page 839

• show events tenant vrf external-l3 ospf, page 840

• show events tenant vrf external-l3 ospf detail, page 841

• show events tenant vrf external-l3 route-map, page 842

• show events tenant vrf external-l3 route-map detail, page 843

• show events tenant vrf external-l3 static-route, page 844

• show events tenant vrf external-l3 static-route detail, page 845

• show events tenant vrf external-l3 static-route node, page 846

• show events tenant vrf external-l3 static-route node detail, page 847

• show external-l2 epg, page 848

• show external-l2 epg name, page 849

• show external-l2 epg tenant, page 850

• show external-l3 bgp, page 851

• show external-l3 bgp tenant, page 852

• show external-l3 bgp tenant vrf, page 853

• show external-l3 bgp tenant vrf node, page 854

• show external-l3 eigrp, page 855

• show external-l3 eigrp detail, page 856

• show external-l3 eigrp node, page 857

• show external-l3 eigrp node detail, page 858

• show external-l3 eigrp tenant, page 859

• show external-l3 eigrp tenant detail, page 860

• show external-l3 eigrp tenant vrf, page 861

• show external-l3 eigrp tenant vrf detail, page 862


S Commands

• show external-l3 eigrp tenant vrf node, page 863

• show external-l3 eigrp tenant vrf node detail, page 864

• show external-l3 epg, page 865

• show external-l3 epg detail, page 866

• show external-l3 epg name, page 867

• show external-l3 epg name detail, page 868

• show external-l3 epg tenant, page 869

• show external-l3 epg tenant detail, page 870

• show external-l3 epg tenant vrf, page 871

• show external-l3 epg tenant vrf detail, page 872

• show external-l3 interfaces, page 873

• show external-l3 interfaces detail, page 874

• show external-l3 interfaces node, page 875

• show external-l3 interfaces node detail, page 876

• show external-l3 interfaces tenant, page 877

• show external-l3 interfaces tenant detail, page 878

• show external-l3 interfaces tenant vrf, page 879

• show external-l3 interfaces tenant vrf detail, page 880

• show external-l3 interfaces tenant vrf node, page 881

• show external-l3 interfaces tenant vrf node detail, page 882

• show external-l3 ospf, page 883

• show external-l3 ospf detail, page 884

• show external-l3 ospf node, page 885

• show external-l3 ospf node detail, page 886

• show external-l3 ospf tenant, page 887

• show external-l3 ospf tenant detail, page 888

• show external-l3 ospf tenant vrf, page 889

• show external-l3 ospf tenant vrf detail, page 890

• show external-l3 ospf tenant vrf node, page 891

• show external-l3 ospf tenant vrf node detail, page 892

• show external-l3 route-map, page 893

• show external-l3 route-map detail, page 894

• show external-l3 route-map name, page 895


S Commands

• show external-l3 route-map name detail, page 896

• show external-l3 route-map tenant, page 897

• show external-l3 route-map tenant detail, page 898

• show external-l3 route-map tenant vrf, page 899

• show external-l3 route-map tenant vrf detail, page 900

• show external-l3 route-map tenant vrf node, page 901

• show external-l3 route-map tenant vrf node detail, page 902

• show external-l3 static-route, page 903

• show external-l3 static-route detail, page 904

• show external-l3 static-route node, page 905

• show external-l3 static-route node detail, page 906

• show external-l3 static-route tenant, page 907

• show external-l3 static-route tenant detail, page 908

• show external-l3 static-route tenant vrf, page 909

• show external-l3 static-route tenant vrf detail, page 910

• show external-l3 static-route tenant vrf node, page 911

• show external-l3 static-route tenant vrf node detail, page 912

• show fabric-recovery status, page 913

• show faults, page 914

• show faults controller, page 916

• show faults controller detail, page 917

• show faults l4l7-cluster, page 918

• show faults l4l7-graph, page 919

• show faults leaf, page 920

• show faults leaf fex, page 921

• show faults leaf fex module, page 922

• show faults leaf interface ethernet, page 923

• show faults leaf interface l3instance, page 924

• show faults leaf interface mgmt, page 925

• show faults leaf interface portchannel, page 926

• show faults leaf interface tunnel, page 927

• show faults leaf inventory chassis, page 928

• show faults leaf inventory fans, page 929


S Commands

• show faults leaf inventory module, page 930

• show faults leaf inventory module fabricport, page 931

• show faults leaf inventory module leafport, page 932

• show faults leaf inventory powersupply, page 933

• show faults leaf inventory supervisor, page 934

• show faults leaf protocol, page 935

• show faults leaf vpc, page 936

• show faults leaf vrf, page 937

• show faults microsoft domain, page 938

• show faults microsoft domain name, page 939

• show faults microsoft domain name hyperv, page 940

• show faults microsoft domain name port-group, page 941

• show faults microsoft domain name scvmm, page 942

• show faults microsoft domain name vm, page 943

• show faults microsoft domain name vm name, page 944

• show faults spine, page 945

• show faults spine interface ethernet, page 946

• show faults spine interface l3instance, page 947

• show faults spine interface mgmt, page 948

• show faults spine interface tunnel, page 949

• show faults spine inventory chassis, page 950

• show faults spine inventory fabric, page 951

• show faults spine inventory fans, page 952

• show faults spine inventory module, page 953

• show faults spine inventory module fabricport, page 954

• show faults spine inventory powersupply, page 955

• show faults spine inventory supervisor, page 956

• show faults spine inventory system, page 957

• show faults spine protocol, page 958

• show faults spine vrf, page 959

• show faults tenant, page 960

• show faults tenant application, page 961

• show faults tenant application epg, page 962


S Commands

• show faults tenant bridge-domain, page 963

• show faults tenant bridge-domain detail, page 964

• show faults tenant interface bridge-domain, page 965

• show faults tenant interface bridge-domain detail, page 966

• show faults tenant vrf, page 967

• show faults tenant vrf detail, page 968

• show faults tenant vrf external-l3 bgp, page 969

• show faults tenant vrf external-l3 bgp node, page 970

• show faults tenant vrf external-l3 eigrp, page 971

• show faults tenant vrf external-l3 eigrp detail, page 972

• show faults tenant vrf external-l3 epg, page 973

• show faults tenant vrf external-l3 epg detail, page 974

• show faults tenant vrf external-l3 epg name, page 975

• show faults tenant vrf external-l3 epg name detail, page 976

• show faults tenant vrf external-l3 interfaces, page 977

• show faults tenant vrf external-l3 interfaces detail, page 978

• show faults tenant vrf external-l3 ospf, page 979

• show faults tenant vrf external-l3 ospf detail, page 980

• show faults tenant vrf external-l3 static-route, page 981

• show faults tenant vrf external-l3 static-route detail, page 982

• show faults tenant vrf external-l3 static-route node, page 983

• show faults tenant vrf external-l3 static-route node detail, page 984

• show faults vmware domain, page 985

• show faults vmware domain name, page 986

• show faults vmware domain name epg, page 987

• show faults vmware domain name esx, page 988

• show faults vmware domain name port-group, page 989

• show faults vmware domain name vcenter, page 990

• show faults vmware domain name vm, page 991

• show faults vmware domain name vm name, page 992

• show firmware repository, page 993

• show firmware repository detail, page 994

• show firmware upgrade status, page 995


S Commands

• show firmware upgrade status controller-group, page 996

• show firmware upgrade status controller-group detail, page 997

• show firmware upgrade status detail, page 998

• show firmware upgrade status switch-group, page 999

• show firmware upgrade status switch-group detail, page 1000

• show health, page 1001

• show health l4l7-cluster, page 1002

• show health l4l7-graph, page 1003

• show health leaf, page 1004

• show health leaf fex, page 1005

• show health leaf fex module, page 1006

• show health leaf interface ethernet, page 1007

• show health leaf interface l3instance, page 1008

• show health leaf interface mgmt, page 1009

• show health leaf interface portchannel, page 1010

• show health leaf interface tunnel, page 1011

• show health leaf inventory chassis, page 1012

• show health leaf inventory fans, page 1013

• show health leaf inventory module, page 1014

• show health leaf inventory module fabricport, page 1015

• show health leaf inventory module leafport, page 1016

• show health leaf inventory powersupply, page 1017

• show health leaf inventory supervisor, page 1018

• show health leaf protocol, page 1019

• show health leaf vpc, page 1020

• show health leaf vrf, page 1021

• show health spine, page 1022

• show health spine interface ethernet, page 1023

• show health spine interface l3instance, page 1024

• show health spine interface mgmt, page 1025

• show health spine interface tunnel, page 1026

• show health spine inventory chassis, page 1027

• show health spine inventory fabric, page 1028


S Commands

• show health spine inventory fans, page 1029

• show health spine inventory module, page 1030

• show health spine inventory module fabricport, page 1031

• show health spine inventory powersupply, page 1032

• show health spine inventory supervisor, page 1033

• show health spine inventory system, page 1034

• show health spine protocol, page 1035

• show health spine vrf, page 1036

• show health tenant, page 1037

• show health tenant application, page 1038

• show health tenant application epg, page 1039

• show health tenant bridge-domain, page 1040

• show health tenant bridge-domain detail, page 1041

• show health tenant interface bridge-domain, page 1042

• show health tenant interface bridge-domain detail, page 1043

• show health tenant vrf, page 1044

• show health tenant vrf detail, page 1045

• show health tenant vrf external-l3 bgp, page 1046

• show health tenant vrf external-l3 bgp node, page 1047

• show health tenant vrf external-l3 eigrp, page 1048

• show health tenant vrf external-l3 eigrp detail, page 1049

• show health tenant vrf external-l3 epg, page 1050

• show health tenant vrf external-l3 epg detail, page 1051

• show health tenant vrf external-l3 epg name, page 1052

• show health tenant vrf external-l3 epg name detail, page 1053

• show health tenant vrf external-l3 interfaces, page 1054

• show health tenant vrf external-l3 interfaces detail, page 1055

• show health tenant vrf external-l3 ospf, page 1056

• show health tenant vrf external-l3 ospf detail, page 1057

• show health tenant vrf external-l3 static-route, page 1058

• show health tenant vrf external-l3 static-route detail, page 1059

• show health tenant vrf external-l3 static-route node, page 1060

• show health tenant vrf external-l3 static-route node detail, page 1061


S Commands

• show inband-mgmt, page 1062

• show inband-mgmt controller, page 1063

• show inband-mgmt switch, page 1064

• show interface bridge-domain, page 1065

• show interface bridge-domain detail, page 1066

• show ip interface bridge-domain, page 1067

• show ipv6 interface bridge-domain, page 1068

• show l4l7-cluster, page 1069

• show l4l7-graph, page 1070

• show l4l7-package, page 1071

• show ldap-server, page 1072

• show locator-led, page 1073

• show locator-led status leaf, page 1074

• show microsoft domain, page 1075

• show microsoft domain name, page 1076

• show microsoft domain name hyperv, page 1077

• show microsoft domain name port-group, page 1078

• show microsoft domain name scvmm, page 1079

• show microsoft domain name vm, page 1080

• show microsoft domain name vm name, page 1081

• show microsoft vm, page 1082

• show monitor access, page 1083

• show monitor fabric, page 1084

• show monitor tenant, page 1085

• show monitor virtual, page 1086

• show ntpq, page 1087

• show oob-mgmt, page 1088

• show oob-mgmt controller, page 1089

• show oob-mgmt switch, page 1090

• show policy-map, page 1091

• show policy-map type data-plane, page 1092

• show policy-map type qos, page 1093

• show port-channel leaf, page 1094


S Commands

• show port-channel map, page 1095

• show port-channel map leaf, page 1096

• show radius-server, page 1097

• show resource, page 1098

• show resource conflict encap-vlan epg, page 1099

• show resource conflict encap-vlan epg node, page 1100

• show role, page 1101

• show running-config, page 1102

• show sessions, page 1103

• show sessions controller, page 1104

• show sessions controller detail, page 1105

• show sessions leaf, page 1106

• show sessions spine, page 1107

• show snapshot active, page 1108

• show snapshot files, page 1109

• show snapshot jobs, page 1110

• show snmp, page 1111

• show snmp clientgroups, page 1112

• show snmp community, page 1113

• show snmp engineid, page 1114

• show snmp hosts, page 1115

• show snmp users, page 1116

• show stats, page 1117

• show stats granularity leaf, page 1118

• show stats granularity leaf fex, page 1119

• show stats granularity leaf fex module, page 1120

• show stats granularity leaf interface ethernet, page 1121

• show stats granularity leaf interface mgmt, page 1122

• show stats granularity leaf interface portchannel, page 1123

• show stats granularity leaf inventory fans, page 1124

• show stats granularity leaf inventory powersupply, page 1125

• show stats granularity leaf inventory supervisor, page 1126

• show stats granularity spine, page 1127


S Commands

• show stats granularity spine interface ethernet, page 1128

• show stats granularity spine interface mgmt, page 1129

• show stats granularity spine inventory chassis, page 1130

• show stats granularity spine inventory fabric, page 1131

• show stats granularity spine inventory fans, page 1132

• show stats granularity spine inventory module, page 1133

• show stats granularity spine inventory powersupply, page 1134

• show stats granularity spine inventory supervisor, page 1135

• show stats granularity spine inventory system, page 1136

• show stats granularity tenant, page 1137

• show stats granularity tenant application, page 1138

• show stats granularity tenant application epg, page 1139

• show switch, page 1140

• show switch detail, page 1141

• show tacacs-server, page 1142

• show techsupport all, page 1143

• show techsupport controllers, page 1144

• show techsupport host, page 1145

• show techsupport switch, page 1146

• show tenant, page 1147

• show tenant access-list, page 1148

• show tenant application, page 1149

• show tenant application endpoints, page 1150

• show tenant application endpoints leaf interface ethernet, page 1151

• show tenant application endpoints leaf interface port-channel, page 1152

• show tenant application endpoints vpc, page 1153

• show tenant application epg, page 1154

• show tenant application epg detail, page 1155

• show tenant application epg endpoints, page 1156

• show tenant application epg endpoints leaf interface ethernet, page 1157

• show tenant application epg endpoints leaf interface port-channel, page 1158

• show tenant application epg endpoints vpc, page 1159

• show tenant bridge-domain, page 1161


S Commands

• show tenant bridge-domain detail, page 1162

• show tenant contract-type, page 1163

• show tenant contract, page 1164

• show tenant detail, page 1165

• show tenant endpoints, page 1166

• show tenant endpoints leaf interface ethernet, page 1167

• show tenant endpoints leaf interface port-channel, page 1168

• show tenant endpoints vpc, page 1169

• show tenant epg, page 1170

• show tenant epg detail, page 1171

• show tenant external-l2 epg, page 1172

• show tenant interface bridge-domain, page 1173

• show tenant interface bridge-domain detail, page 1174

• show tenant ip interface bridge-domain, page 1175

• show tenant ipv6 interface bridge-domain, page 1176

• show tenant policy-map, page 1177

• show tenant policy-map type data-plane, page 1178

• show tenant policy-map type qos, page 1179

• show tenant vrf, page 1180

• show tenant vrf detail, page 1181

• show tenant vrf external-l3 bgp, page 1182

• show tenant vrf external-l3 bgp node, page 1183

• show tenant vrf external-l3 eigrp, page 1184

• show tenant vrf external-l3 eigrp detail, page 1185

• show tenant vrf external-l3 epg, page 1186

• show tenant vrf external-l3 epg detail, page 1187

• show tenant vrf external-l3 epg name, page 1188

• show tenant vrf external-l3 epg name detail, page 1189

• show tenant vrf external-l3 interfaces, page 1190

• show tenant vrf external-l3 interfaces detail, page 1191

• show tenant vrf external-l3 ospf, page 1192

• show tenant vrf external-l3 ospf detail, page 1193

• show tenant vrf external-l3 route-map, page 1194


S Commands

• show tenant vrf external-l3 route-map detail, page 1195

• show tenant vrf external-l3 static-route, page 1196

• show tenant vrf external-l3 static-route detail, page 1197

• show tenant vrf external-l3 static-route node, page 1198

• show tenant vrf external-l3 static-route node detail, page 1199

• show troubleshoot epext session, page 1200

• show troubleshoot epext session atomiccounter, page 1201

• show troubleshoot epext session audit, page 1202

• show troubleshoot epext session contracts, page 1203

• show troubleshoot epext session deployments, page 1204

• show troubleshoot epext session events, page 1205

• show troubleshoot epext session faults, page 1206

• show troubleshoot epext session monitor, page 1207

• show troubleshoot epext session reports, page 1208

• show troubleshoot epext session statistics, page 1209

• show troubleshoot epext session topology, page 1210

• show troubleshoot epext session traceroute, page 1211

• show troubleshoot epext sessions, page 1212

• show troubleshoot eptoep session, page 1213

• show troubleshoot eptoep session atomiccounter, page 1214

• show troubleshoot eptoep session audit, page 1215

• show troubleshoot eptoep session contracts, page 1216

• show troubleshoot eptoep session deployments, page 1217

• show troubleshoot eptoep session events, page 1218

• show troubleshoot eptoep session faults, page 1219

• show troubleshoot eptoep session monitor, page 1220

• show troubleshoot eptoep session reports, page 1221

• show troubleshoot eptoep session statistics, page 1222

• show troubleshoot eptoep session topology, page 1223

• show troubleshoot eptoep session traceroute, page 1224

• show troubleshoot eptoep sessions, page 1225

• show username, page 1226

• show username detail, page 1227


S Commands

• show version, page 1228

• show vlan-domain, page 1229

• show vmware domain, page 1230

• show vmware domain name, page 1231

• show vmware domain name epg, page 1232

• show vmware domain name esx, page 1233

• show vmware domain name port-group, page 1234

• show vmware domain name vcenter, page 1235

• show vmware domain name vm, page 1236

• show vmware domain name vm name, page 1237

• show vmware vm, page 1238

• show vpc, page 1239

• show vpc map leaf, page 1240

• show vrf, page 1241

• show vrf detail, page 1242

• shut, page 1243

• shutdown, page 1244

• site-id, page 1246

• slow-timer, page 1247

• snapshot download, page 1248

• snapshot export, page 1249

• snapshot import, page 1250

• snapshot rollback, page 1251

• snapshot upload, page 1252

• snmp-server clientgroup, page 1253

• snmp-server community, page 1254

• snmp-server contact, page 1255

• snmp-server host, page 1256

• snmp-server location, page 1257

• snmp-server protocol, page 1258

• snmp-server user, page 1259

• source, page 1260

• source application, page 1261


S Commands

• source interface ethernet, page 1262

• source interface port-channel, page 1263

• source interface vpc, page 1264

• spanning-tree, page 1265

• spanning-tree bpdu-filter, page 1268

• spanning-tree bpdu-guard, page 1269

• speed, page 1270

• spf-interval, page 1272

• ssh-key, page 1273

• ssh-service, page 1274

• ssl-protocols, page 1275

• ssl-validation-level, page 1276

• state, page 1277

• static-endpoint, page 1278

• static-tep, page 1281

• statistics, page 1283

• storm-control level, page 1284

• storm-control pps, page 1286

• street-address, page 1289

• subject, page 1290

• summary-address, page 1291

• switch-group, page 1292

• switch, page 1293

• switching, page 1294

• switchport, page 1295

• switchport access vlan tenant application, page 1297

• switchport access vlan tenant external-svi, page 1299

• switchport trunk allowed vlan inband-mgmt, page 1301

• switchport trunk allowed vlan tenant application, page 1302

• switchport trunk allowed vlan tenant external-l2, page 1304

• switchport trunk allowed vlan tenant external-svi, page 1306

• switchport trunk allowed vlan tenant legacy-forwarding, page 1308

• switchport trunk native vlan tenant application, page 1310


S Commands

• switchport trunk native vlan tenant external-svi, page 1312

• switchport vlan, page 1314

• syslog, page 1316

• system cluster-size, page 1317

• system controller-id, page 1318

• system dynamic-load-balance, page 1319

• system fabric-security-mode, page 1320

• system jumbomtu, page 1321

• system switch-id, page 1322


S Commands

scheduleschedule <WORD>

Description: Assign a scheduler

Syntax:

scheduler name (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# firmware(config-firmware)# switch-group <WORD>(config-firmware-switch)# schedule <WORD>

schedule <WORD>

Description: Schedule snapshot export

Syntax:

Scheduler nameWORD


Command Path:

# configure [['terminal', 't']](config)# snapshot export <WORD>(config-export)# schedule <WORD>


S Commandsschedule

schedulerscheduler pause

Description: Pause maintenance policy scheduler

Syntax:

Pause maintenance policy schedulerpause


Command Path:

# configure [['terminal', 't']](config)# firmware(config-firmware)# switch-group <WORD>(config-firmware-switch)# scheduler pause

scheduler fabric|controller schedule <WORD>

Description: Scheduler configuration mode

Syntax:

Fabric schedulesfabric

Controller schedulescontroller

Configure a scheduleschedule

Schedule name (Max size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# scheduler fabric|controller schedule <WORD>


S Commandsscheduler

schedulingscheduling <WORD>

Description: Set the scheduling algorithm

Syntax:

Algorithm to chooseWORD


Command Path:

# configure [['terminal', 't']](config)# qos parameters level1|level2|level3(config-qos)# scheduling <WORD>


S Commandsscheduling

scopescope <WORD>

Description: Specify the scope for the contract

Syntax:

Contract ScopeWORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# contract <WORD> [type <type>](config-tenant-contract)# scope <WORD>

scope global

Description: Set scope

Syntax:

Route-map will be available for use on all nodes in this tenant and vrfglobal


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# scope global


S Commandsscope

scvmmscvmm <arg> cloud <WORD> [name <name>]

Description: Configure an SCVMM in the Microsoft domain

Syntax:

arg

Cloud namecloud

Cloud Name (Max Size 512)WORD

(Optional) SCVMM Controller Namename

Command Mode: microsoft-domain : Create a VMMMicrosoft Domain

Command Path:

# configure [['terminal', 't']](config)# microsoft-domain <WORD>(config-microsoft)# scvmm <> cloud <WORD> [name <name>]


S Commandsscvmm

second-filesecond-file <FILENAME>

Description: Second snapshot file name

Syntax:

Second snapshot file nameFILENAME


Command Path:

# configure [['terminal', 't']](config)# snapshot rollback <WORD>(config-rollback)# second-file <FILENAME>


S Commandssecond-file

security-domainsecurity-domain <WORD>

Description: Add security domain

Syntax:

Security-domain nameWORD

Command Mode: vlan-domain : Configure vlan domain

Command Path:

# configure [['terminal', 't']](config)# vlan-domain <name> [dynamic] [type <domain-type>](config-vlan)# security-domain <WORD>

security-domain <WORD>

Description: Add a security domain to this VMware domain

Syntax:

Security domain name (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# vmware-domain <WORD>(config-vmware)# security-domain <WORD>


S Commandssecurity-domain

securitysecurity domain <WORD>

Description: Add a security domain to the tenant

Syntax:

Domaindomain

Security domain name (Max Size None)WORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# security domain <WORD>


S Commandssecurity

send-communitysend-community [extended]

Description: Send Community attribute to this neighbor

Syntax:

(Optional) Send Extended Community attributeextended


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [l3out <WORD>](config-leaf-bgp-vrf-neighbor)# send-community [extended]


S Commandssend-community

serverserver <A.B.C.D|A:B::C:D|WORD> priority <NUMBER>

Description: Add LDAP server to LDAP group

Syntax:

LDAP server name or IP addressA.B.C.D|A:B::C:D|WORD

priority of server within grouppriority

Priority of server within group. Number range from=0 to=16<0-16>

Command Mode: aaa group server ldap : LDAP server group name.

Command Path:

# configure [['terminal', 't']](config)# aaa group server ldap <WORD>(config-ldap)# server <A.B.C.D|A:B::C:D|WORD> priority <NUMBER>

server <A.B.C.D|A:B::C:D|WORD> priority <NUMBER>

Description: Add RADIUS server to RADIUS group

Syntax:

RADIUS server name or IP addressA.B.C.D|A:B::C:D|WORD



Command Mode: aaa group server radius : RADIUS server group name.

Command Path:

# configure [['terminal', 't']](config)# aaa group server radius <WORD>(config-radius)# server <A.B.C.D|A:B::C:D|WORD> priority <NUMBER>

server <A.B.C.D|A:B::C:D|WORD> priority <NUMBER>

Description: Add TACACS PLUS server to TACACS PLUS group

Syntax:

TACACS PLUS server name or IP addressA.B.C.D|A:B::C:D|WORD


S Commandsserver



Command Mode: aaa group server tacacsplus : TACACS+ server group name.

Command Path:

# configure [['terminal', 't']](config)# aaa group server tacacsplus <WORD>(config-tacacsplus)# server <A.B.C.D|A:B::C:D|WORD> priority <NUMBER>

server <WORD> [prefer] [key <arg>] [use-vrf <arg>]

Description: Configure ntp servers for the active ntp policy

Syntax:

Server name/IP for the active ntp policy (Max Size 64)WORD

(Optional) Preferred server for the active ntp policyprefer

(Optional) Reference key id for authentication. Number range from=1to=65535

arg

(Optional) Configure management vrfarg


Command Path:

# configure [['terminal', 't']](config)# pod 1(config-pod)# ntp(config-ntp)# server <WORD> [prefer] [key <>] [use-vrf <>]

server <host/ipaddr> [facility <facility>] [severity <severity>] [mgmtepg <mgmtepg>] [port <port>]

Description: Add a destination server

Syntax:

The hostname or ipaddress<host/ipaddr>

(Optional) The forwarding facility level for logs generatedfacility

(Optional) The severity level for logs generatedseverity

(Optional) MgmtEndpointmgmtepg


S Commandsserver

(Optional) Service port of the remote destination. Number range from=1to=65535

port


Command Path:

# configure [['terminal', 't']](config)# logging server-group <WORD>(config-logging)# server <host/ipaddr> [facility <facility>] [severity <severity>] [mgmtepg<mgmtepg>] [port <port>]


S Commandsserver

service-policyservice-policy <WORD>

Description: Specify the QOS service policy

Syntax:

Qos Service Policy (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# service-policy <WORD>

service-policy <WORD>

Description: Specify the QOS service policy

Syntax:

Service policy to apply (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l2 epg <WORD>(config-tenant-l2ext-epg)# service-policy <WORD>

service-policy type data-plane input|output <WORD>

Description: QOS service policy

Syntax:



Ingress Directioninput

Egress Directionoutput


S Commandsservice-policy

Qos Policy Name (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# service-policy type data-plane input|output <WORD>



Syntax:







Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# service-policy type data-plane input|output <WORD>



Syntax:









Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# service-policy type data-plane input|output <WORD>



Syntax:







Command Path:

# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# service-policy type data-plane input|output <WORD>



serviceservice <WORD> [device-cluster-tenant <WORD>] [device-cluster <WORD>] [mode <Available Modes>]

Description: Configure L4-L7 Service

Syntax:

Service node name (Max Size 64)WORD

(Optional) Tenant name (Max Size 63)WORD

(Optional) Device cluster name (Max Size 64)WORD

(Optional) DescriptionAvailable Modes


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 graph <WORD> [contract <contract-option>](config-graph)# service <WORD> [device-cluster-tenant <WORD>] [device-cluster <WORD>] [mode<Available Modes>]


S Commandsservice

session-record-flagssession-record-flags <sessionRecordFlags>

Description: Enable/Disable refresh in the session records, Comma separated values

Syntax:

Session record flags as comma separated values like val1,val2,..valN<sessionRecordFlags>


Command Path:

# configure [['terminal', 't']](config)# crypto webtoken(config-webtoken)# session-record-flags <sessionRecordFlags>


S Commandssession-record-flags

setset qos-class <WORD>

Description: QOS level for the epg

Syntax:

QOS level for the epgqos-class

Qos LevelWORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# set qos-class <WORD>

set qos-class <WORD>

Description: QOS level for the application

Syntax:

QOS level for the applicationqos-class

Qos LevelWORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# set qos-class <WORD>

set qos-class <contractQosLevel>

Description: Specify the QOS level for the epg

Syntax:

class of QOS to specifyqos-class

{unspecified|level1|level2|level3}<contractQosLevel>


S Commandsset


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# inband-mgmt epg <WORD>(config-inb-epg)# set qos-class <contractQosLevel>

set qos-class <WORD>


Syntax:

QOS level for the epgqos-class

Qos LevelWORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l2 epg <WORD>(config-tenant-l2ext-epg)# set qos-class <WORD>

set qos-class <contractQosLevel>


Syntax:

class of QOS to specifyqos-class

{unspecified|level1|level2|level3}<contractQosLevel>


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# oob-mgmt epg <epgval>(config-oob-epg)# set qos-class <contractQosLevel>


S Commandsset

set burstset burst <0-4294967295> UNIT

Description: Burst Rate

Syntax:

Burst Rate<0-4294967295>

Burst Rate UnitUNIT

Command Mode: policy-map : Create a policymap of DataPlane type to police/reclassify the traffic

Command Path:

# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>(config-pmap-dpp)# set burst <0-4294967295> UNIT

set burst <0-4294967295> UNIT

Description: Burst Rate

Syntax:

Burst Rate<0-4294967295>

Burst Rate UnitUNIT

Command Mode: policy-map type data-plane : data-plane policy type

Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>(config-tenant-pmap-dpp)# set burst <0-4294967295> UNIT


S Commandsset burst

set cirset cir <0-4294967295> UNIT

Description: Committed Rate

Syntax:

Committed Rate<0-4294967295>

Committed Rate UnitUNIT


Command Path:

# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>(config-pmap-dpp)# set cir <0-4294967295> UNIT

set cir <0-4294967295> UNIT

Description: Committed Rate

Syntax:

Committed Rate<0-4294967295>

Committed Rate UnitUNIT


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>(config-tenant-pmap-dpp)# set cir <0-4294967295> UNIT


S Commandsset cir

set communityset community regular|extended <value> additive|replace|none

Description: Set BGP community attribute

Syntax:

BGP regular communityregular

BGP extended communityextended

Community value in aa:nn formatvalue

Add to existing communityadditive

Replace existing communityreplace

Do not change communitynone

Command Mode: route-profile : Configure route-profile

Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# route-profile <WORD>(config-tenant-vrf-route-profile)# set community regular|extended <value>additive|replace|none

set community regular|extended <value> additive|replace|none


Syntax:








S Commandsset community

CommandMode: template route-profile : Configure route-profile template under tenant for BGP dampeningand route redistribution

Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template route-profile <WORD> tenant <WORD>(config-leaf-template-route-profile)# set community regular|extended <value>additive|replace|none



Syntax:








Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match prefix-list <WORD>(config-leaf-vrf-route-map-match)# set community regular|extended <value>additive|replace|none



Syntax:









Command Mode: match community : Configure community features

Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match community <WORD>(config-leaf-vrf-route-map-match)# set community regular|extended <value>additive|replace|none



Syntax:







Command Mode: template route-profile : Configure route-profile template under VRF/L3Out forbridge-domain export

Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# template route-profile <WORD>(config-leaf-vrf-template-route-profile)# set community regular|extended <value>additive|replace|none



set conform-cos-transmitset conform-cos-transmit <0-6>

Description: Conform Policer Mark Cos

Syntax:

Conform Policer Mark Cos<0-6>


Command Path:

# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>(config-pmap-dpp)# set conform-cos-transmit <0-6>

set conform-cos-transmit <0-6>

Description: Conform Policer Mark Cos

Syntax:

Conform Policer Mark Cos<0-6>


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>(config-tenant-pmap-dpp)# set conform-cos-transmit <0-6>


S Commandsset conform-cos-transmit

set conform-dscp-transmitset conform-dscp-transmit <0-63>

Description: Conform Policer Mark DSCP

Syntax:

Conform Policer Mark DSCP<0-63>


Command Path:

# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>(config-pmap-dpp)# set conform-dscp-transmit <0-63>

set conform-dscp-transmit <0-63>

Description: Conform Policer Mark DSCP

Syntax:

Conform Policer Mark DSCP<0-63>


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>(config-tenant-pmap-dpp)# set conform-dscp-transmit <0-63>


S Commandsset conform-dscp-transmit

set conformset conform <WORD>

Description: Conform Policer Action

Syntax:

Conform Policer ActionWORD


Command Path:

# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>(config-pmap-dpp)# set conform <WORD>

set conform <WORD>

Description: Conform Policer Action

Syntax:

Conform Policer ActionWORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>(config-tenant-pmap-dpp)# set conform <WORD>


S Commandsset conform

set dampeningset dampening <NUMBER> <NUMBER> <NUMBER> <NUMBER>

Description: Route Flap dampening

Syntax:

Decay half life. Number range from=1 to=60<1-60>

Value to start reusing a route. Number range from=1 to=20000<1-20000>

Value to start suppressing a route. Number range from=1 to=20000<1-20000>

Maximum suppress time for stable route. Number range from=1 to=255<1-255>


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template route-profile <WORD> tenant <WORD>(config-leaf-template-route-profile)# set dampening <NUMBER> <NUMBER> <NUMBER> <NUMBER>


S Commandsset dampening

set dscpset dscp <WORD>

Description: Specify the DSCP level for the EPG

Syntax:

DSCP valueWORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l3 epg <WORD> [oob-mgmt] [l3out <l3out>](config-tenant-l3ext-epg)# set dscp <WORD>


S Commandsset dscp

set exceed-cos-transmitset exceed-cos-transmit <0-6>

Description: Exceed Policer Mark Cos

Syntax:

Exceed Policer Mark Cos<0-6>


Command Path:

# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>(config-pmap-dpp)# set exceed-cos-transmit <0-6>

set exceed-cos-transmit <0-6>

Description: Exceed Policer Mark Cos

Syntax:

Exceed Policer Mark Cos<0-6>


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>(config-tenant-pmap-dpp)# set exceed-cos-transmit <0-6>


S Commandsset exceed-cos-transmit

set exceed-dscp-transmitset exceed-dscp-transmit <0-63>

Description: Exceed Policer Mark DSCP

Syntax:

Exceed Policer Mark DSCP<0-63>


Command Path:

# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>(config-pmap-dpp)# set exceed-dscp-transmit <0-63>

set exceed-dscp-transmit <0-63>

Description: Exceed Policer Mark DSCP

Syntax:

Exceed Policer Mark DSCP<0-63>


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>(config-tenant-pmap-dpp)# set exceed-dscp-transmit <0-63>


S Commandsset exceed-dscp-transmit

set exceedset exceed <WORD>

Description: Exceed Policer Action

Syntax:

Exceed Policer ActionWORD


Command Path:

# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>(config-pmap-dpp)# set exceed <WORD>

set exceed <WORD>

Description: Exceed Policer Action

Syntax:

Exceed Policer ActionWORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>(config-tenant-pmap-dpp)# set exceed <WORD>


S Commandsset exceed

set excessive-burstset excessive-burst <0-4294967295> UNIT

Description: Excessive Burst Rate

Syntax:

Excessive Burst Rate<0-4294967295>

Excessive Burst Rate UnitUNIT


Command Path:

# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>(config-pmap-dpp)# set excessive-burst <0-4294967295> UNIT

set excessive-burst <0-4294967295> UNIT

Description: Excessive Burst Rate

Syntax:

Excessive Burst Rate<0-4294967295>

Excessive Burst Rate UnitUNIT


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>(config-tenant-pmap-dpp)# set excessive-burst <0-4294967295> UNIT


S Commandsset excessive-burst

set local-preferenceset local-preference <0-4294967295>

Description: BGP local preference path attribute

Syntax:

Preference value<0-4294967295>


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# route-profile <WORD>(config-tenant-vrf-route-profile)# set local-preference <0-4294967295>

set local-preference <0-4294967295>


Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template route-profile <WORD> tenant <WORD>(config-leaf-template-route-profile)# set local-preference <0-4294967295>



Syntax:



Command Path:



S Commandsset local-preference

(config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match prefix-list <WORD>(config-leaf-vrf-route-map-match)# set local-preference <0-4294967295>



Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match community <WORD>(config-leaf-vrf-route-map-match)# set local-preference <0-4294967295>



Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# template route-profile <WORD>(config-leaf-vrf-template-route-profile)# set local-preference <0-4294967295>


S Commandsset local-preference

set metric-typeset metric-type <metric-type>

Description: Type of metric for destination routing protocol

Syntax:

<metric-type><metric-type>


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# route-profile <WORD>(config-tenant-vrf-route-profile)# set metric-type <metric-type>

set metric-type <metric-type>


Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template route-profile <WORD> tenant <WORD>(config-leaf-template-route-profile)# set metric-type <metric-type>



Syntax:



Command Path:



S Commandsset metric-type

(config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match prefix-list <WORD>(config-leaf-vrf-route-map-match)# set metric-type <metric-type>



Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match community <WORD>(config-leaf-vrf-route-map-match)# set metric-type <metric-type>



Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# template route-profile <WORD>(config-leaf-vrf-template-route-profile)# set metric-type <metric-type>


S Commandsset metric-type

set metricset metric <NUMBER>

Description: Set metric for destination routing protocol

Syntax:

Metric value. Number range from=0 to=255<0-255>


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# route-profile <WORD>(config-tenant-vrf-route-profile)# set metric <NUMBER>

set metric <NUMBER>


Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template route-profile <WORD> tenant <WORD>(config-leaf-template-route-profile)# set metric <NUMBER>

set metric <NUMBER>


Syntax:



Command Path:



S Commandsset metric

(config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match prefix-list <WORD>(config-leaf-vrf-route-map-match)# set metric <NUMBER>

set metric <NUMBER>


Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match community <WORD>(config-leaf-vrf-route-map-match)# set metric <NUMBER>

set metric <NUMBER>


Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# template route-profile <WORD>(config-leaf-vrf-template-route-profile)# set metric <NUMBER>


S Commandsset metric

set modeset mode <WORD>

Description: Policer Mode

Syntax:

Policer ModeWORD


Command Path:

# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>(config-pmap-dpp)# set mode <WORD>

set mode <WORD>

Description: Policer Mode

Syntax:

Policer ModeWORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>(config-tenant-pmap-dpp)# set mode <WORD>


S Commandsset mode

set pirset pir <0-4294967295> UNIT

Description: Peak Rate

Syntax:

Peak Rate<0-4294967295>

Pir UnitUNIT


Command Path:

# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>(config-pmap-dpp)# set pir <0-4294967295> UNIT

set pir <0-4294967295> UNIT

Description: Peak Rate

Syntax:

Peak Rate<0-4294967295>

Pir UnitUNIT


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>(config-tenant-pmap-dpp)# set pir <0-4294967295> UNIT


S Commandsset pir

set qos-classset qos-class <WORD>

Description: Class of QOS to specify

Syntax:

Qos LevelWORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# contract <WORD> [type <type>](config-tenant-contract)# set qos-class <WORD>

set qos-class unspecified|level1|level2|level3

Description: Specify the QOS level for the EPG

Syntax:

Unspecified QoS levelunspecified

QoS level1level1

QoS level2level2

QoS level3level3


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l3 epg <WORD> [oob-mgmt] [l3out <l3out>](config-tenant-l3ext-epg)# set qos-class unspecified|level1|level2|level3


S Commandsset qos-class

set tagset tag <NUMBER>

Description: Tag value for destination routing protocol

Syntax:

Tag value. Number range from=0 to=4294967295<0-4294967295>


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# route-profile <WORD>(config-tenant-vrf-route-profile)# set tag <NUMBER>

set tag <NUMBER>


Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template route-profile <WORD> tenant <WORD>(config-leaf-template-route-profile)# set tag <NUMBER>

set tag <NUMBER>


Syntax:



Command Path:



S Commandsset tag

(config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match prefix-list <WORD>(config-leaf-vrf-route-map-match)# set tag <NUMBER>

set tag <NUMBER>


Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match community <WORD>(config-leaf-vrf-route-map-match)# set tag <NUMBER>

set tag <NUMBER>


Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# template route-profile <WORD>(config-leaf-vrf-template-route-profile)# set tag <NUMBER>


S Commandsset tag

set target-dscpset target-dscp <WORD>

Description: class of target dscp to specify

Syntax:

Target dscpWORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# contract <WORD> [type <type>](config-tenant-contract)# set target-dscp <WORD>

set target-dscp <WORD> WORD

Description: class of target dscp to specify

Syntax:

Target dscpWORD

Target DSCP DirectionWORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# contract <WORD> [type <type>](config-tenant-contract)# subject <WORD>(config-tenant-contract-subj)# set target-dscp <WORD> WORD


S Commandsset target-dscp

set typeset type <WORD>

Description: Policer type

Syntax:

Policer TypeWORD


Command Path:

# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>(config-pmap-dpp)# set type <WORD>

set type <WORD>

Description: Policer type

Syntax:

Policer TypeWORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>(config-tenant-pmap-dpp)# set type <WORD>


S Commandsset type

set violate-cos-transmitset violate-cos-transmit <0-6>

Description: Violate Policer Mark Cos

Syntax:

Violate Policer Mark Cos<0-6>


Command Path:

# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>(config-pmap-dpp)# set violate-cos-transmit <0-6>

set violate-cos-transmit <0-6>

Description: Violate Policer Mark Cos

Syntax:

Violate Policer Mark Cos<0-6>


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>(config-tenant-pmap-dpp)# set violate-cos-transmit <0-6>


S Commandsset violate-cos-transmit

set violate-dscp-transmitset violate-dscp-transmit <0-63>

Description: Violate Policer Mark DSCP

Syntax:

Violate Policer Mark DSCP<0-63>


Command Path:

# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>(config-pmap-dpp)# set violate-dscp-transmit <0-63>

set violate-dscp-transmit <0-63>

Description: Violate Policer Mark DSCP

Syntax:

Violate Policer Mark DSCP<0-63>


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>(config-tenant-pmap-dpp)# set violate-dscp-transmit <0-63>


S Commandsset violate-dscp-transmit

set violateset violate <WORD>

Description: Violate Policer Action

Syntax:

Violate Policer ActionWORD


Command Path:

# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>(config-pmap-dpp)# set violate <WORD>

set violate <WORD>

Description: Violate Policer Action

Syntax:

Violate Policer ActionWORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>(config-tenant-pmap-dpp)# set violate <WORD>


S Commandsset violate

set weightset weight <NUMBER>

Description:Weight value for destination routing protocol

Syntax:

Weight value. Number range from=0 to=65535<0-65535>


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# route-profile <WORD>(config-tenant-vrf-route-profile)# set weight <NUMBER>

set weight <NUMBER>


Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template route-profile <WORD> tenant <WORD>(config-leaf-template-route-profile)# set weight <NUMBER>

set weight <NUMBER>


Syntax:



Command Path:



S Commandsset weight

(config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match prefix-list <WORD>(config-leaf-vrf-route-map-match)# set weight <NUMBER>

set weight <NUMBER>


Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match community <WORD>(config-leaf-vrf-route-map-match)# set weight <NUMBER>

set weight <NUMBER>


Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# template route-profile <WORD>(config-leaf-vrf-template-route-profile)# set weight <NUMBER>


S Commandsset weight

shellinaboxshellinabox

Description: Configures the communication policy of the SHELLINABOX feature


Usage:

In the APIC GUI, the SHELLINABOX feature allows you to open a pop-up SSH session to a fabric switchby right-clicking the icon of the switch. To enable or disable this feature, use the shellinabox command toenter the SHELLINABOX communication policy group, then use the [no] admin-state-enable command.

Command Path:

# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# shellinabox


S Commandsshellinabox

show aaa authenticationshow aaa authentication

Description: Show AAA Authentication information


Command Path:

# show aaa authentication


S Commandsshow aaa authentication

show aaa groupsshow aaa groups

Description: Show AAA group information


Command Path:

# show aaa groups


S Commandsshow aaa groups

show access-listshow access-list WORD

Description: Show Access-list Information

Syntax:

Name of the Contract to filter on (Max Size 64)WORD


Command Path:

# show access-list WORD


S Commandsshow access-list

show accounting logshow accounting log

Description: CLI configuration command logs


Command Path:

# show accounting log

NOTE:

This command displays only those changes made using the command line interface (CLI). It does not displaychanges made using the GUI or the API. To view all changes made in the Management Information Tree, usethe show audit detail command.


S Commandsshow accounting log

show applicationshow application WORD

Description: Show Application Profiles Information

Syntax:

Name of the application we eventually want to filter on (Max Size 64)WORD


Command Path:

# show application WORD


S Commandsshow application

show auditsshow audits [id <log-id>] [action action<action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] <scope>

Description: Show audit-log information

Syntax:

(Optional) Log ID<log-id>

(Optional) Object action indicatoraction<action-type>

(Optional) Name of user<user-name>

(Optional) Logs created in time interval. Number range from=1 to=59<num-minutes>

(Optional) Logs created in time interval. Number range from=1 to=23<num-hours>

(Optional) Logs created in time interval. Number range from=1 to=999<num-days>

(Optional) Logs created in time interval<YYYY-MM-DDTHR:MIN:SEC>

(Optional) Logs created in time intervalend-time<YYYY-MM-DDTHR:MIN:SEC>

(Optional) Detailed audit-log information. Displays what was modifiedand displays the old and new settings.

detail

command scope<scope>


Command Path:

# show audits [id <log-id>] [action action<action-type>] [user <user-name>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] <scope>


S Commandsshow audits

show audits tenantshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD

Description: Show Tenants Information

Syntax:

Name of the tenant to filter on (Max Size 63)WORD


Command Path:

# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD


S Commandsshow audits tenant

show audits tenant applicationshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD application WORD


Syntax:




Command Path:

# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD application WORD


S Commandsshow audits tenant application

show audits tenant application epgshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD application WORD epg WORD

Description: Show Application EPG Information

Syntax:



Name of the AEPG to filter on (Max Size 64)WORD


Command Path:

# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD application WORD epg WORD


S Commandsshow audits tenant application epg

show audits tenant bridge-domainshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD

Description: Show Bridge-domain Information

Syntax:




Command Path:

# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD


S Commandsshow audits tenant bridge-domain

show audits tenant bridge-domain detailshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD detail

Description: Show Bridge-domain Detailed Information

Syntax:




Command Path:

# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD detail


S Commandsshow audits tenant bridge-domain detail

show audits tenant interface bridge-domainshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD


Syntax:




Command Path:

# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD


S Commandsshow audits tenant interface bridge-domain

show audits tenant interface bridge-domain detailshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD detail


Syntax:




Command Path:

# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD detail


S Commandsshow audits tenant interface bridge-domain detail

show audits tenant vrfshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD

Description: Show VRF Information

Syntax:


Name of the VRF to filter on (Max Size 64)WORD


Command Path:

# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD


S Commandsshow audits tenant vrf

show audits tenant vrf detailshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD detail

Description: Show detailed view of VRF

Syntax:




Command Path:

# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD detail


S Commandsshow audits tenant vrf detail

show audits tenant vrf external-l3 bgpshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 bgp

Description: Show command for BGP peers

Syntax:




Command Path:

# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 bgp


S Commandsshow audits tenant vrf external-l3 bgp

show audits tenant vrf external-l3 bgp nodeshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 bgp node <101-4000>

Description: node to filter on

Syntax:





Command Path:

# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 bgp node <101-4000>


S Commandsshow audits tenant vrf external-l3 bgp node

show audits tenant vrf external-l3 eigrpshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 eigrp

Description: Show external l3 EIGRP

Syntax:




Command Path:

# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 eigrp


S Commandsshow audits tenant vrf external-l3 eigrp

show audits tenant vrf external-l3 eigrp detailshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 eigrp detail

Description: Show interanl details

Syntax:




Command Path:

# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 eigrp detail


S Commandsshow audits tenant vrf external-l3 eigrp detail

show audits tenant vrf external-l3 epgshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName>

Description: Show command for external-l3 epgs

Syntax:



Name of the EPG to filter on<epgName>


Command Path:

# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName>


S Commandsshow audits tenant vrf external-l3 epg

show audits tenant vrf external-l3 epg detailshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName> detail

Description: external-l3 epg in detail with operational status

Syntax:





Command Path:

# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName> detail


S Commandsshow audits tenant vrf external-l3 epg detail

show audits tenant vrf external-l3 epg nameshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName> name <epgName>

Description: EPG name to filter on

Syntax:






Command Path:

# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName> name<epgName>


S Commandsshow audits tenant vrf external-l3 epg name

show audits tenant vrf external-l3 epg name detailshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName> name <epgName>detail


Syntax:






Command Path:

# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName> name<epgName> detail


S Commandsshow audits tenant vrf external-l3 epg name detail

show audits tenant vrf external-l3 interfacesshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 interfaces

Description: Show tenant <tenant> vrf <vrf> external l3 interfaces

Syntax:




Command Path:

# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 interfaces


S Commandsshow audits tenant vrf external-l3 interfaces

show audits tenant vrf external-l3 interfaces detailshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 interfaces detail


Syntax:




Command Path:

# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 interfaces detail


S Commandsshow audits tenant vrf external-l3 interfaces detail

show audits tenant vrf external-l3 ospfshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 ospf

Description: Show commad for IPv4 and IPv6 external l3 OSPF configuration

Syntax:




Command Path:

# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 ospf


S Commandsshow audits tenant vrf external-l3 ospf

show audits tenant vrf external-l3 ospf detailshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 ospf detail


Syntax:




Command Path:

# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 ospf detail


S Commandsshow audits tenant vrf external-l3 ospf detail

show audits tenant vrf external-l3 static-routeshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route

Description: Show command for external-l3 static routes

Syntax:




Command Path:

# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route


S Commandsshow audits tenant vrf external-l3 static-route

show audits tenant vrf external-l3 static-route detailshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route detail

Description: static-route in detail with operational status

Syntax:




Command Path:

# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route detail


S Commandsshow audits tenant vrf external-l3 static-route detail

show audits tenant vrf external-l3 static-route nodeshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route node


Syntax:



Leaf Range or Leaf Name Listarg


Command Path:

# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route node


S Commandsshow audits tenant vrf external-l3 static-route node

show audits tenant vrf external-l3 static-route node detailshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route node detail


Syntax:





Command Path:

# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route node detail


S Commandsshow audits tenant vrf external-l3 static-route node detail

show bridge-domainshow bridge-domain WORD


Syntax:



Command Path:

# show bridge-domain WORD


S Commandsshow bridge-domain

show bridge-domain detailshow bridge-domain WORD detail


Syntax:



Command Path:

# show bridge-domain WORD detail


S Commandsshow bridge-domain detail

show callhomeshow callhome common

Description: Show command for callhome

Syntax:

Commoncommon


Command Path:

# show callhome common


S Commandsshow callhome

show callhome common destination-profileshow callhome common destination-profile

Description: Show command for callhome destination-profile

Syntax:

Commoncommon


Command Path:

# show callhome common destination-profile


S Commandsshow callhome common destination-profile

show callhome common query-profileshow callhome common query-profile

Description: Show command for callhome destination-profile

Syntax:

Commoncommon


Command Path:

# show callhome common query-profile


S Commandsshow callhome common query-profile

show callhome common transport-emailshow callhome common transport-email

Description: Show command for callhome transport-email

Syntax:

Commoncommon


Command Path:

# show callhome common transport-email


S Commandsshow callhome common transport-email

show catalogshow catalog

Description: Show catalog information


Command Path:

# show catalog


S Commandsshow catalog

show cli commandshow cli command <WORD> [mode <mode-name>]

Description: Show Commands Syntax

Syntax:

Command Name pattern between single quotesWORD

(Optional) Mode name pattern between single quotes<mode-name>

(Optional) Show Command Detailsdetails


Command Path:

# show cli command <WORD> [mode <mode-name>]


S Commandsshow cli command

show cli internal auditshow cli internal audit

Description: Show Commands Audit


Command Path:

# show cli internal audit


S Commandsshow cli internal audit

show cli internal transactionshow cli internal transaction logs|xml <NUMBER>

Description: Show Transaction Details

Syntax:

Show Transaction Logslogs

Show Transaction XML Postxml

Transaction ID(TID) to grep log lines with similar TIDs. TID can beextracted from the 'show cli internal audit' command. Number rangefrom=0 to=9223372036854775807

<Transaction ID>


Command Path:

# show cli internal transaction logs|xml <NUMBER>


S Commandsshow cli internal transaction

show cli listshow cli list [mode <mode-name>]

Description: Show all cli-related commands

Syntax:




Command Path:

# show cli list [mode <mode-name>]


S Commandsshow cli list

show cli manpageshow cli manpage <WORD> [mode <mode-name>]

Description: Show Commands ManPage

Syntax:





Command Path:

# show cli manpage <WORD> [mode <mode-name>]


S Commandsshow cli manpage

show cli pathshow cli path <WORD> [mode <mode-name>]

Description: Show Commands Path

Syntax:





Command Path:

# show cli path <WORD> [mode <mode-name>]


S Commandsshow cli path

show clockshow clock

Description: Show clock information


Command Path:

# show clock


S Commandsshow clock

show communication ciphersshow communication ciphers

Description: HTTPS service cipher suite listings


Command Path:

# show communication ciphers


S Commandsshow communication ciphers

show communication httpshow communication http

Description: HTTP service settings


Command Path:

# show communication http


S Commandsshow communication http

show communication httpsshow communication https

Description: HTTPS service settings


Command Path:

# show communication https


S Commandsshow communication https

show communication shellinaboxshow communication shellinabox

Description: Shellinabox service settings


Command Path:

# show communication shellinabox


S Commandsshow communication shellinabox

show communication ssh-serviceshow communication ssh-service

Description: SSH service settings


Command Path:

# show communication ssh-service


S Commandsshow communication ssh-service

show communication telnetshow communication telnet

Description: Telnet service settings


Command Path:

# show communication telnet


S Commandsshow communication telnet

show communication web-requestsshow communication web-requests

Description: Status of last web requests


Command Path:

# show communication web-requests


S Commandsshow communication web-requests

show contract-typeshow contract-type WORD

Description: Show Contracts Information Based on Type

Syntax:

whitelist (permit) or blacklist(deny) or oob-mgmt type of contractWORD


Command Path:

# show contract-type WORD


S Commandsshow contract-type

show contractshow contract WORD

Description: Show Contracts Information

Syntax:



Command Path:

# show contract WORD


S Commandsshow contract

show controllershow controller

Description: Show controller information


Command Path:

# show controller


S Commandsshow controller

show controller detailshow controller detail [id <node-id>]

Description: Detailed controller information

Syntax:

(Optional) Optional Serial numbernode-id


Command Path:

# show controller detail [id <node-id>]


S Commandsshow controller detail

show coresshow cores

Description: Show all core dumps


Command Path:

# show cores


S Commandsshow cores

show debug countershow debug <node-name> <process> counter <counterTopics>

Description: Show Counter information

Syntax:



Counter Topics<counterTopics>


Command Path:

# show debug <node-name> <process> counter <counterTopics>


S Commandsshow debug counter

show debug logshow debug <node-name> <process> log

Description: Show log level information

Syntax:




Command Path:

# show debug <node-name> <process> log


S Commandsshow debug log

show dns-addressshow dns-address

Description: Show dns address information


Command Path:

# show dns-address


S Commandsshow dns-address

show dns-domainshow dns-domain

Description: Show dns domain information


Command Path:

# show dns-domain


S Commandsshow dns-domain

show endpointsshow endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan<NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>]

Description: Show IP endpoints

Syntax:

(Optional) Endpoint Typetype

(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)

E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE

(Optional) Encapsulation Vlan. Number range from=1 to=4094<1-4094>

(Optional) IP address in format i.i.i.iA.B.C.D

(Optional) IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D


Command Path:

# show endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE>] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>]


S Commandsshow endpoints

show endpoints leaf interface ethernetshow endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan<NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interface ethernet ethernet [<fex>/]<slot>/<port>

Description: Show IP endpoints on an interface ethernet

Syntax:








WORD

Ethernet Rangeethernet [<fex>/]<slot>/<port>


Command Path:

# show endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE>] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interface ethernet ethernet[<fex>/]<slot>/<port>


S Commandsshow endpoints leaf interface ethernet

show endpoints leaf interface port-channelshow endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan<NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interface port-channel <WORD> [fex <NUMBER>]

Description: Show IP endpoints on an interface port-channel

Syntax:








WORD

Port Channel Name (Max Size 64)WORD

(Optional) Fex Id. Number range from=101 to=164<101-164>


Command Path:

# show endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE>] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interface port-channel<WORD> [fex <NUMBER>]


S Commandsshow endpoints leaf interface port-channel

show endpoints vpcshow endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan<NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] vpc context <WORD> <WORD> interface vpc <WORD> [fex<fex>]

Description: Show IP endpoints on vpc

Syntax:







VPC Contextcontext

First VPC leaf (Max Size 4000). Number range from=0to=9223372036854775807

WORD

Second VPC leaf (Max Size 4000). Number range from=0to=9223372036854775807

WORD

VPC Interface nameinterface

VPC Interface namevpc




Command Path:

# show endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE>] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] vpc context <WORD> <WORD> interfacevpc <WORD> [fex <fex>]


S Commandsshow endpoints vpc

show epgshow epg WORD


Syntax:



Command Path:

# show epg WORD


S Commandsshow epg

show epg detailshow epg WORD detail

Description: Show detailed view of Application EPg

Syntax:



Command Path:

# show epg WORD detail


S Commandsshow epg detail

show eventsshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] <scope>

Description: Show event information

Syntax:

(Optional) Event code<event-code>

(Optional) Event ID<event-ID>

(Optional) Cause<event-value>

(Optional) Event activity in time interval. Number range from=1 to=59last-minutes <num-minutes>

(Optional) Event activity in time interval. Number range from=1 to=23last-hours <num-hours>

(Optional) Event activity in time interval. Number range from=1 to=999last-days <num-days>

(Optional) Event activity in time intervalstart-time<YYYY-MM-DDTHR:MIN:SEC>

(Optional) Event activity in time intervalend-time<YYYY-MM-DDTHR:MIN:SEC>

(Optional) Detailed event informationdetail



Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] <scope>


S Commandsshow events

show events controllershow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] controller



Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] controller


S Commandsshow events controller

show events controller detailshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] controller detail [id <node-id>]


Syntax:



Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] controller detail [id <node-id>]


S Commandsshow events controller detail

show events leafshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId>

Description: Show command for leaf

Syntax:

Leaf id<leafId>


Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId>


S Commandsshow events leaf

show events leaf fexshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> fex <fexNum>

Description: Show extended chassis information

Syntax:

Leaf id<leafId>

pls enter fex number<fexNum>


Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> fex <fexNum>


S Commandsshow events leaf fex

show events leaf fex moduleshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> fex <fexNum> module <lcSlot>

Description: Show inventory module information

Syntax:

Leaf id<leafId>


please enter the module number<lcSlot>


Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> fex <fexNum> module <lcSlot>


S Commandsshow events leaf fex module

show events leaf interface ethernetshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface ethernet <phyInt>


Syntax:

Leaf id<leafId>

<slot or chassis-number/port or slot number><phyInt>


Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface ethernet <phyInt>


S Commandsshow events leaf interface ethernet

show events leaf interface l3instanceshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface l3instance <l3Inst>

Description: L3 instance

Syntax:

Leaf id<leafId>

<L3 instance number><l3Inst>


Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface l3instance <l3Inst>


S Commandsshow events leaf interface l3instance

show events leaf interface mgmtshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface mgmt <mgmtPort>

Description:Management interface

Syntax:

Leaf id<leafId>

<Management interface number><mgmtPort>


Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface mgmt <mgmtPort>


S Commandsshow events leaf interface mgmt

show events leaf interface portchannelshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface portchannel <portChan>

Description: Port channel interface

Syntax:

Leaf id<leafId>

<Port channel number><portChan>


Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface portchannel <portChan>


S Commandsshow events leaf interface portchannel

show events leaf interface tunnelshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface tunnel <tunnelPort>

Description: Tunnel Interface

Syntax:

Leaf id<leafId>

<Tunnel interface number><tunnelPort>


Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface tunnel <tunnelPort>


S Commandsshow events leaf interface tunnel

show events leaf inventory chassisshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory chassis <ch>

Description: Show inventory chassis information

Syntax:

Leaf id<leafId>

None<ch>


Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory chassis <ch>


S Commandsshow events leaf inventory chassis

show events leaf inventory fansshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory fans <ftSlot>

Description: Show inventory fan information

Syntax:

Leaf id<leafId>

pls enter fan tray number<ftSlot>


Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory fans <ftSlot>


S Commandsshow events leaf inventory fans

show events leaf inventory moduleshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory module <lcSlot>


Syntax:

Leaf id<leafId>



Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory module <lcSlot>


S Commandsshow events leaf inventory module

show events leaf inventory module fabricportshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory module <lcSlot> fabricport <fabPort>

Description: Show information for fabric port

Syntax:

Leaf id<leafId>


pls enter the fabric port number<fabPort>


Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory module <lcSlot> fabricport<fabPort>


S Commandsshow events leaf inventory module fabricport

show events leaf inventory module leafportshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory module <lcSlot> leafport <leafPort>

Description: Show information for leaf port

Syntax:

Leaf id<leafId>


pls enter the leaf port number<leafPort>


Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory module <lcSlot> leafport<leafPort>


S Commandsshow events leaf inventory module leafport

show events leaf inventory powersupplyshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory powersupply <psuSlot>

Description: Show inventory power supply information

Syntax:

Leaf id<leafId>

pls enter the powersupply number<psuSlot>


Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory powersupply <psuSlot>


S Commandsshow events leaf inventory powersupply

show events leaf inventory supervisorshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory supervisor <supMod>

Description: Show information for supervisor module

Syntax:

Leaf id<leafId>

pls enter the supervisor module number<supMod>


Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory supervisor <supMod>


S Commandsshow events leaf inventory supervisor

show events leaf protocolshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> protocol <protName>

Description: Show command for protocol

Syntax:

Leaf id<leafId>

Protocol name<protName>


Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> protocol <protName>


S Commandsshow events leaf protocol

show events leaf vpcshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> vpc <vpcPort>

Description: Virtual port channel information

Syntax:

Leaf id<leafId>

pls enter virtual port channel number<vpcPort>


Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> vpc <vpcPort>


S Commandsshow events leaf vpc

show events leaf vrfshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> vrf <vrfPort>

Description: Vrf information

Syntax:

Leaf id<leafId>

pls enter vrf name<vrfPort>


Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> vrf <vrfPort>


S Commandsshow events leaf vrf

show events spineshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId>

Description: Show command for spine

Syntax:

Leaf id<leafId>


Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId>


S Commandsshow events spine

show events spine interface ethernetshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interface ethernet <phyInt>


Syntax:

Leaf id<leafId>



Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interface ethernet <phyInt>


S Commandsshow events spine interface ethernet

show events spine interface l3instanceshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interface l3instance <l3Inst>


Syntax:

Leaf id<leafId>



Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interface l3instance <l3Inst>


S Commandsshow events spine interface l3instance

show events spine interface mgmtshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interface mgmt <mgmtPort>


Syntax:

Leaf id<leafId>



Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interface mgmt <mgmtPort>


S Commandsshow events spine interface mgmt

show events spine interface tunnelshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interface tunnel <tunnelPort>


Syntax:

Leaf id<leafId>



Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interface tunnel <tunnelPort>


S Commandsshow events spine interface tunnel

show events spine inventory chassisshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory chassis


Syntax:

Leaf id<leafId>


Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory chassis


S Commandsshow events spine inventory chassis

show events spine inventory fabricshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory fabric <fcMod>

Description: Show information for fabric module

Syntax:

Leaf id<leafId>

pls enter the fabric module number<fcMod>


Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory fabric <fcMod>


S Commandsshow events spine inventory fabric

show events spine inventory fansshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory fans <ftSlot>


Syntax:

Leaf id<leafId>



Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory fans <ftSlot>


S Commandsshow events spine inventory fans

show events spine inventory moduleshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory module <lcSlot>


Syntax:

Leaf id<leafId>



Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory module <lcSlot>


S Commandsshow events spine inventory module

show events spine inventory module fabricportshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory module <lcSlot> fabricport <fabPort>


Syntax:

Leaf id<leafId>




Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory module <lcSlot>fabricport <fabPort>


S Commandsshow events spine inventory module fabricport

show events spine inventory powersupplyshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory powersupply <psuSlot>


Syntax:

Leaf id<leafId>



Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory powersupply <psuSlot>


S Commandsshow events spine inventory powersupply

show events spine inventory supervisorshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory supervisor <supMod>


Syntax:

Leaf id<leafId>



Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory supervisor <supMod>


S Commandsshow events spine inventory supervisor

show events spine inventory systemshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory system <sysMod>

Description: Show information for system module

Syntax:

Leaf id<leafId>

pls enter the system module number<sysMod>


Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory system <sysMod>


S Commandsshow events spine inventory system

show events spine protocolshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> protocol <protName>


Syntax:

Leaf id<leafId>



Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> protocol <protName>


S Commandsshow events spine protocol

show events spine vrfshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> vrf <vrfPort>


Syntax:

Leaf id<leafId>



Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> vrf <vrfPort>


S Commandsshow events spine vrf

show events tenantshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD


Syntax:



Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD


S Commandsshow events tenant

show events tenant applicationshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD application WORD


Syntax:




Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD application WORD


S Commandsshow events tenant application

show events tenant application epgshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD application WORD epg WORD


Syntax:





Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD application WORD epg WORD


S Commandsshow events tenant application epg

show events tenant bridge-domainshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD


Syntax:




Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD


S Commandsshow events tenant bridge-domain

show events tenant bridge-domain detailshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD detail


Syntax:




Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD detail


S Commandsshow events tenant bridge-domain detail

show events tenant endpointsshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>]


Syntax:









Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD endpoints [type <type>] [mac <E.E.EEE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6<A:B::C:D>]


S Commandsshow events tenant endpoints

show events tenant endpoints leaf interface ethernetshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interfaceethernet ethernet [<fex>/]<slot>/<port>


Syntax:









WORD



Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD endpoints [type <type>] [mac <E.E.EEE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6<A:B::C:D>] leaf <WORD> interface ethernet ethernet [<fex>/]<slot>/<port>


S Commandsshow events tenant endpoints leaf interface ethernet

show events tenant endpoints leaf interface port-channelshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interfaceport-channel <WORD> [fex <NUMBER>]


Syntax:









WORD




Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD endpoints [type <type>] [mac <E.E.EEE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6<A:B::C:D>] leaf <WORD> interface port-channel <WORD> [fex <NUMBER>]


S Commandsshow events tenant endpoints leaf interface port-channel

show events tenant endpoints vpcshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] vpc context <WORD><WORD> interface vpc <WORD> [fex <fex>]


Syntax:








VPC Contextcontext


WORD


WORD






Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD endpoints [type <type>] [mac <E.E.EEE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6


S Commandsshow events tenant endpoints vpc

<A:B::C:D>] vpc context <WORD> <WORD> interface vpc <WORD> [fex <fex>]


S Commandsshow events tenant endpoints vpc

show events tenant interface bridge-domainshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD


Syntax:




Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD


S Commandsshow events tenant interface bridge-domain

show events tenant interface bridge-domain detailshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD detail


Syntax:




Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD detail


S Commandsshow events tenant interface bridge-domain detail

show events tenant vrfshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD


Syntax:




Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD


S Commandsshow events tenant vrf

show events tenant vrf detailshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD detail


Syntax:




Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD detail


S Commandsshow events tenant vrf detail

show events tenant vrf external-l3 bgpshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 bgp


Syntax:




Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 bgp


S Commandsshow events tenant vrf external-l3 bgp

show events tenant vrf external-l3 bgp nodeshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 bgp node <101-4000>


Syntax:





Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 bgp node<101-4000>


S Commandsshow events tenant vrf external-l3 bgp node

show events tenant vrf external-l3 eigrpshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 eigrp


Syntax:




Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 eigrp


S Commandsshow events tenant vrf external-l3 eigrp

show events tenant vrf external-l3 eigrp detailshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 eigrp detail


Syntax:




Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 eigrp detail


S Commandsshow events tenant vrf external-l3 eigrp detail

show events tenant vrf external-l3 epgshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName>


Syntax:





Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName>


S Commandsshow events tenant vrf external-l3 epg

show events tenant vrf external-l3 epg detailshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName> detail


Syntax:





Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName>detail


S Commandsshow events tenant vrf external-l3 epg detail

show events tenant vrf external-l3 epg nameshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName> name <epgName>


Syntax:






Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName>name <epgName>


S Commandsshow events tenant vrf external-l3 epg name

show events tenant vrf external-l3 epg name detailshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName> name <epgName>detail


Syntax:






Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName>name <epgName> detail


S Commandsshow events tenant vrf external-l3 epg name detail

show events tenant vrf external-l3 interfacesshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 interfaces


Syntax:




Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 interfaces


S Commandsshow events tenant vrf external-l3 interfaces

show events tenant vrf external-l3 interfaces detailshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 interfaces detail


Syntax:




Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 interfacesdetail


S Commandsshow events tenant vrf external-l3 interfaces detail

show events tenant vrf external-l3 ospfshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 ospf


Syntax:




Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 ospf


S Commandsshow events tenant vrf external-l3 ospf

show events tenant vrf external-l3 ospf detailshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 ospf detail


Syntax:




Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 ospf detail


S Commandsshow events tenant vrf external-l3 ospf detail

show events tenant vrf external-l3 route-mapshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 route-map [name <l3out name>]

Description: Show command for external-l3 route-map

Syntax:



(Optional) Name of the route-map to filter on<l3out name>


Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 route-map [name<l3out name>]


S Commandsshow events tenant vrf external-l3 route-map

show events tenant vrf external-l3 route-map detailshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 route-map [name <l3out name>]detail

Description: Show external-l3 route-map in detail with operational status

Syntax:





Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 route-map [name<l3out name>] detail


S Commandsshow events tenant vrf external-l3 route-map detail

show events tenant vrf external-l3 static-routeshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route


Syntax:




Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route


S Commandsshow events tenant vrf external-l3 static-route

show events tenant vrf external-l3 static-route detailshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route detail


Syntax:




Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-routedetail


S Commandsshow events tenant vrf external-l3 static-route detail

show events tenant vrf external-l3 static-route nodeshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route node


Syntax:





Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-routenode


S Commandsshow events tenant vrf external-l3 static-route node

show events tenant vrf external-l3 static-route node detailshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route node detail


Syntax:





Command Path:

# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-routenode detail


S Commandsshow events tenant vrf external-l3 static-route node detail

show external-l2 epgshow external-l2 epg



Command Path:

# show external-l2 epg


S Commandsshow external-l2 epg

show external-l2 epg nameshow external-l2 epg name WORD


Syntax:

Name of the EPG to filter on (Max Size 64)WORD


Command Path:

# show external-l2 epg name WORD


S Commandsshow external-l2 epg name

show external-l2 epg tenantshow external-l2 epg tenant WORD

Description: tenant to filter on

Syntax:



Command Path:

# show external-l2 epg tenant WORD


S Commandsshow external-l2 epg tenant

show external-l3 bgpshow external-l3 bgp



Command Path:

# show external-l3 bgp


S Commandsshow external-l3 bgp

show external-l3 bgp tenantshow external-l3 bgp tenant <WORD>


Syntax:



Command Path:

# show external-l3 bgp tenant <WORD>


S Commandsshow external-l3 bgp tenant

show external-l3 bgp tenant vrfshow external-l3 bgp tenant <WORD> vrf WORD

Description: vrf to filter on

Syntax:




Command Path:

# show external-l3 bgp tenant <WORD> vrf WORD


S Commandsshow external-l3 bgp tenant vrf

show external-l3 bgp tenant vrf nodeshow external-l3 bgp tenant <WORD> vrf WORD node <101-4000>


Syntax:





Command Path:

# show external-l3 bgp tenant <WORD> vrf WORD node <101-4000>


S Commandsshow external-l3 bgp tenant vrf node

show external-l3 eigrpshow external-l3 eigrp

Description: Show command for external-l3 eigrp


Command Path:

# show external-l3 eigrp


S Commandsshow external-l3 eigrp

show external-l3 eigrp detailshow external-l3 eigrp detail



Command Path:

# show external-l3 eigrp detail


S Commandsshow external-l3 eigrp detail

show external-l3 eigrp nodeshow external-l3 eigrp node <101-4000>

Description: node(s) to filter on

Syntax:

Node Range or Node Name List<101-4000>


Command Path:

# show external-l3 eigrp node <101-4000>


S Commandsshow external-l3 eigrp node

show external-l3 eigrp node detailshow external-l3 eigrp node <101-4000> detail


Syntax:



Command Path:

# show external-l3 eigrp node <101-4000> detail


S Commandsshow external-l3 eigrp node detail

show external-l3 eigrp tenantshow external-l3 eigrp tenant <WORD>

Description: tenant(s) to filter on

Syntax:



Command Path:

# show external-l3 eigrp tenant <WORD>


S Commandsshow external-l3 eigrp tenant

show external-l3 eigrp tenant detailshow external-l3 eigrp tenant <WORD> detail


Syntax:



Command Path:

# show external-l3 eigrp tenant <WORD> detail


S Commandsshow external-l3 eigrp tenant detail

show external-l3 eigrp tenant vrfshow external-l3 eigrp tenant <WORD> vrf WORD

Description: vrf(s) to filter on

Syntax:


Name of the VRF(s) to filter on (Max Size 64)WORD


Command Path:

# show external-l3 eigrp tenant <WORD> vrf WORD


S Commandsshow external-l3 eigrp tenant vrf

show external-l3 eigrp tenant vrf detailshow external-l3 eigrp tenant <WORD> vrf WORD detail


Syntax:




Command Path:

# show external-l3 eigrp tenant <WORD> vrf WORD detail


S Commandsshow external-l3 eigrp tenant vrf detail

show external-l3 eigrp tenant vrf nodeshow external-l3 eigrp tenant <WORD> vrf WORD node <101-4000>


Syntax:





Command Path:

# show external-l3 eigrp tenant <WORD> vrf WORD node <101-4000>


S Commandsshow external-l3 eigrp tenant vrf node

show external-l3 eigrp tenant vrf node detailshow external-l3 eigrp tenant <WORD> vrf WORD node <101-4000> detail


Syntax:





Command Path:

# show external-l3 eigrp tenant <WORD> vrf WORD node <101-4000> detail


S Commandsshow external-l3 eigrp tenant vrf node detail

show external-l3 epgshow external-l3 epg



Command Path:

# show external-l3 epg


S Commandsshow external-l3 epg

show external-l3 epg detailshow external-l3 epg detail



Command Path:

# show external-l3 epg detail


S Commandsshow external-l3 epg detail

show external-l3 epg nameshow external-l3 epg name <epgName>


Syntax:



Command Path:

# show external-l3 epg name <epgName>


S Commandsshow external-l3 epg name

show external-l3 epg name detailshow external-l3 epg name <epgName> detail


Syntax:



Command Path:

# show external-l3 epg name <epgName> detail


S Commandsshow external-l3 epg name detail

show external-l3 epg tenantshow external-l3 epg tenant <WORD>


Syntax:



Command Path:

# show external-l3 epg tenant <WORD>


S Commandsshow external-l3 epg tenant

show external-l3 epg tenant detailshow external-l3 epg tenant <WORD> detail


Syntax:



Command Path:

# show external-l3 epg tenant <WORD> detail


S Commandsshow external-l3 epg tenant detail

show external-l3 epg tenant vrfshow external-l3 epg tenant <WORD> vrf WORD


Syntax:




Command Path:

# show external-l3 epg tenant <WORD> vrf WORD


S Commandsshow external-l3 epg tenant vrf

show external-l3 epg tenant vrf detailshow external-l3 epg tenant <WORD> vrf WORD detail


Syntax:




Command Path:

# show external-l3 epg tenant <WORD> vrf WORD detail


S Commandsshow external-l3 epg tenant vrf detail

show external-l3 interfacesshow external-l3 interfaces

Description: Show command for external-l3 interfaces


Command Path:

# show external-l3 interfaces


S Commandsshow external-l3 interfaces

show external-l3 interfaces detailshow external-l3 interfaces detail



Command Path:

# show external-l3 interfaces detail


S Commandsshow external-l3 interfaces detail

show external-l3 interfaces nodeshow external-l3 interfaces node <101-4000>


Syntax:



Command Path:

# show external-l3 interfaces node <101-4000>


S Commandsshow external-l3 interfaces node

show external-l3 interfaces node detailshow external-l3 interfaces node <101-4000> detail


Syntax:



Command Path:

# show external-l3 interfaces node <101-4000> detail


S Commandsshow external-l3 interfaces node detail

show external-l3 interfaces tenantshow external-l3 interfaces tenant <WORD>


Syntax:



Command Path:

# show external-l3 interfaces tenant <WORD>


S Commandsshow external-l3 interfaces tenant

show external-l3 interfaces tenant detailshow external-l3 interfaces tenant <WORD> detail


Syntax:



Command Path:

# show external-l3 interfaces tenant <WORD> detail


S Commandsshow external-l3 interfaces tenant detail

show external-l3 interfaces tenant vrfshow external-l3 interfaces tenant <WORD> vrf WORD


Syntax:




Command Path:

# show external-l3 interfaces tenant <WORD> vrf WORD


S Commandsshow external-l3 interfaces tenant vrf

show external-l3 interfaces tenant vrf detailshow external-l3 interfaces tenant <WORD> vrf WORD detail


Syntax:




Command Path:

# show external-l3 interfaces tenant <WORD> vrf WORD detail


S Commandsshow external-l3 interfaces tenant vrf detail

show external-l3 interfaces tenant vrf nodeshow external-l3 interfaces tenant <WORD> vrf WORD node <101-4000>


Syntax:





Command Path:

# show external-l3 interfaces tenant <WORD> vrf WORD node <101-4000>


S Commandsshow external-l3 interfaces tenant vrf node

show external-l3 interfaces tenant vrf node detailshow external-l3 interfaces tenant <WORD> vrf WORD node <101-4000> detail


Syntax:





Command Path:

# show external-l3 interfaces tenant <WORD> vrf WORD node <101-4000> detail


S Commandsshow external-l3 interfaces tenant vrf node detail

show external-l3 ospfshow external-l3 ospf

Description: Show command for external-l3 ospf


Command Path:

# show external-l3 ospf


S Commandsshow external-l3 ospf

show external-l3 ospf detailshow external-l3 ospf detail



Command Path:

# show external-l3 ospf detail


S Commandsshow external-l3 ospf detail

show external-l3 ospf nodeshow external-l3 ospf node <101-4000>


Syntax:



Command Path:

# show external-l3 ospf node <101-4000>


S Commandsshow external-l3 ospf node

show external-l3 ospf node detailshow external-l3 ospf node <101-4000> detail


Syntax:



Command Path:

# show external-l3 ospf node <101-4000> detail


S Commandsshow external-l3 ospf node detail

show external-l3 ospf tenantshow external-l3 ospf tenant <WORD>


Syntax:



Command Path:

# show external-l3 ospf tenant <WORD>


S Commandsshow external-l3 ospf tenant

show external-l3 ospf tenant detailshow external-l3 ospf tenant <WORD> detail


Syntax:



Command Path:

# show external-l3 ospf tenant <WORD> detail


S Commandsshow external-l3 ospf tenant detail

show external-l3 ospf tenant vrfshow external-l3 ospf tenant <WORD> vrf WORD


Syntax:




Command Path:

# show external-l3 ospf tenant <WORD> vrf WORD


S Commandsshow external-l3 ospf tenant vrf

show external-l3 ospf tenant vrf detailshow external-l3 ospf tenant <WORD> vrf WORD detail


Syntax:




Command Path:

# show external-l3 ospf tenant <WORD> vrf WORD detail


S Commandsshow external-l3 ospf tenant vrf detail

show external-l3 ospf tenant vrf nodeshow external-l3 ospf tenant <WORD> vrf WORD node <101-4000>


Syntax:





Command Path:

# show external-l3 ospf tenant <WORD> vrf WORD node <101-4000>


S Commandsshow external-l3 ospf tenant vrf node

show external-l3 ospf tenant vrf node detailshow external-l3 ospf tenant <WORD> vrf WORD node <101-4000> detail


Syntax:





Command Path:

# show external-l3 ospf tenant <WORD> vrf WORD node <101-4000> detail


S Commandsshow external-l3 ospf tenant vrf node detail

show external-l3 route-mapshow external-l3 route-map



Command Path:

# show external-l3 route-map


S Commandsshow external-l3 route-map

show external-l3 route-map detailshow external-l3 route-map detail

Description: Route-map in detail with operational status


Command Path:

# show external-l3 route-map detail


S Commandsshow external-l3 route-map detail

show external-l3 route-map nameshow external-l3 route-map name <l3out name>

Description: Route-map name to filter on

Syntax:

Name of the route-map to filter on<l3out name>


Command Path:

# show external-l3 route-map name <l3out name>


S Commandsshow external-l3 route-map name

show external-l3 route-map name detailshow external-l3 route-map name <l3out name> detail


Syntax:

Name of the route-map to filter on<l3out name>


Command Path:

# show external-l3 route-map name <l3out name> detail


S Commandsshow external-l3 route-map name detail

show external-l3 route-map tenantshow external-l3 route-map tenant <WORD>


Syntax:



Command Path:

# show external-l3 route-map tenant <WORD>


S Commandsshow external-l3 route-map tenant

show external-l3 route-map tenant detailshow external-l3 route-map tenant <WORD> detail


Syntax:



Command Path:

# show external-l3 route-map tenant <WORD> detail


S Commandsshow external-l3 route-map tenant detail

show external-l3 route-map tenant vrfshow external-l3 route-map tenant <WORD> vrf WORD


Syntax:




Command Path:

# show external-l3 route-map tenant <WORD> vrf WORD


S Commandsshow external-l3 route-map tenant vrf

show external-l3 route-map tenant vrf detailshow external-l3 route-map tenant <WORD> vrf WORD detail


Syntax:




Command Path:

# show external-l3 route-map tenant <WORD> vrf WORD detail


S Commandsshow external-l3 route-map tenant vrf detail

show external-l3 route-map tenant vrf nodeshow external-l3 route-map tenant <WORD> vrf WORD node


Syntax:





Command Path:

# show external-l3 route-map tenant <WORD> vrf WORD node


S Commandsshow external-l3 route-map tenant vrf node

show external-l3 route-map tenant vrf node detailshow external-l3 route-map tenant <WORD> vrf WORD node detail


Syntax:





Command Path:

# show external-l3 route-map tenant <WORD> vrf WORD node detail


S Commandsshow external-l3 route-map tenant vrf node detail

show external-l3 static-routeshow external-l3 static-route



Command Path:

# show external-l3 static-route


S Commandsshow external-l3 static-route

show external-l3 static-route detailshow external-l3 static-route detail



Command Path:

# show external-l3 static-route detail


S Commandsshow external-l3 static-route detail

show external-l3 static-route nodeshow external-l3 static-route node


Syntax:



Command Path:

# show external-l3 static-route node


S Commandsshow external-l3 static-route node

show external-l3 static-route node detailshow external-l3 static-route node detail


Syntax:



Command Path:

# show external-l3 static-route node detail


S Commandsshow external-l3 static-route node detail

show external-l3 static-route tenantshow external-l3 static-route tenant <WORD>


Syntax:



Command Path:

# show external-l3 static-route tenant <WORD>


S Commandsshow external-l3 static-route tenant

show external-l3 static-route tenant detailshow external-l3 static-route tenant <WORD> detail


Syntax:



Command Path:

# show external-l3 static-route tenant <WORD> detail


S Commandsshow external-l3 static-route tenant detail

show external-l3 static-route tenant vrfshow external-l3 static-route tenant <WORD> vrf WORD


Syntax:




Command Path:

# show external-l3 static-route tenant <WORD> vrf WORD


S Commandsshow external-l3 static-route tenant vrf

show external-l3 static-route tenant vrf detailshow external-l3 static-route tenant <WORD> vrf WORD detail


Syntax:




Command Path:

# show external-l3 static-route tenant <WORD> vrf WORD detail


S Commandsshow external-l3 static-route tenant vrf detail

show external-l3 static-route tenant vrf nodeshow external-l3 static-route tenant <WORD> vrf WORD node


Syntax:





Command Path:

# show external-l3 static-route tenant <WORD> vrf WORD node


S Commandsshow external-l3 static-route tenant vrf node

show external-l3 static-route tenant vrf node detailshow external-l3 static-route tenant <WORD> vrf WORD node detail


Syntax:





Command Path:

# show external-l3 static-route tenant <WORD> vrf WORD node detail


S Commandsshow external-l3 static-route tenant vrf node detail

show fabric-recovery statusshow fabric-recovery status

Description: Show fabric recovery status


Command Path:

# show fabric-recovery status


S Commandsshow fabric-recovery status

show faultsshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes/no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] <scope>

Description: Show fault information

Syntax:

(Optional) Historical informationhistory

(Optional) Fault code<fault-code>

(Optional) Fault ID<fault-ID>

(Optional) Acknowledgment status<yes/no>

(Optional) Lifecycle state<lc-state>

(Optional) Severity<severity-value>

(Optional) Minimum severity<severity-value>

(Optional) Type<fault-type>

(Optional) Cause<fault-value>

(Optional) Fault activity in time interval. Number range from=1 to=59last-minutes <num-minutes>

(Optional) Fault activity in time interval. Number range from=1 to=23last-hours <num-hours>

(Optional) Fault activity in time interval. Number range from=1 to=999last-days <num-days>

(Optional) Fault activity in time intervalstart-time<YYYY-MM-DDTHR:MIN:SEC>

(Optional) Fault activity in time intervalend-time<YYYY-MM-DDTHR:MIN:SEC>

(Optional) Detailed faults informationdetail




S Commandsshow faults

Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes/no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-timestart-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail]<scope>


S Commandsshow faults

show faults controllershow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] controller



Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] controller


S Commandsshow faults controller

show faults controller detailshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] controller detail [id <node-id>]


Syntax:



Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] controller detail [id<node-id>]


S Commandsshow faults controller detail

show faults l4l7-clustershow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] l4l7-cluster [tenant <Tenant Name>] [cluster <Device Cluster Name>]

Description: Show L4 L7 Device information

Syntax:

(Optional) Name of TenantTenant Name

(Optional) Name of DeviceDevice Cluster Name


Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] l4l7-cluster [tenant<Tenant Name>] [cluster <Device Cluster Name>]


S Commandsshow faults l4l7-cluster

show faults l4l7-graphshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] l4l7-graph [tenant <Tenant Name>] [graph <Graph Name>]

Description: Show L4 L7 Graph information

Syntax:

(Optional) Name of Tenant<Tenant Name>

(Optional) Name of Graph<Graph Name>


Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] l4l7-graph [tenant<Tenant Name>] [graph <Graph Name>]


S Commandsshow faults l4l7-graph

show faults leafshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId>


Syntax:

Leaf id<leafId>


Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId>


S Commandsshow faults leaf

show faults leaf fexshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> fex <fexNum>


Syntax:

Leaf id<leafId>



Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> fex<fexNum>


S Commandsshow faults leaf fex

show faults leaf fex moduleshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> fex <fexNum> module <lcSlot>


Syntax:

Leaf id<leafId>




Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> fex<fexNum> module <lcSlot>


S Commandsshow faults leaf fex module

show faults leaf interface ethernetshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface ethernet <phyInt>


Syntax:

Leaf id<leafId>



Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interfaceethernet <phyInt>


S Commandsshow faults leaf interface ethernet

show faults leaf interface l3instanceshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface l3instance <l3Inst>


Syntax:

Leaf id<leafId>



Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interfacel3instance <l3Inst>


S Commandsshow faults leaf interface l3instance

show faults leaf interface mgmtshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface mgmt <mgmtPort>


Syntax:

Leaf id<leafId>



Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interfacemgmt <mgmtPort>


S Commandsshow faults leaf interface mgmt

show faults leaf interface portchannelshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface portchannel <portChan>


Syntax:

Leaf id<leafId>



Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interfaceportchannel <portChan>


S Commandsshow faults leaf interface portchannel

show faults leaf interface tunnelshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface tunnel <tunnelPort>


Syntax:

Leaf id<leafId>



Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interfacetunnel <tunnelPort>


S Commandsshow faults leaf interface tunnel

show faults leaf inventory chassisshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory chassis <ch>


Syntax:

Leaf id<leafId>

None<ch>


Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventorychassis <ch>


S Commandsshow faults leaf inventory chassis

show faults leaf inventory fansshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory fans <ftSlot>


Syntax:

Leaf id<leafId>



Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventoryfans <ftSlot>


S Commandsshow faults leaf inventory fans

show faults leaf inventory moduleshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory module <lcSlot>


Syntax:

Leaf id<leafId>



Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventorymodule <lcSlot>


S Commandsshow faults leaf inventory module

show faults leaf inventory module fabricportshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory module <lcSlot> fabricport <fabPort>


Syntax:

Leaf id<leafId>




Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventorymodule <lcSlot> fabricport <fabPort>


S Commandsshow faults leaf inventory module fabricport

show faults leaf inventory module leafportshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory module <lcSlot> leafport <leafPort>


Syntax:

Leaf id<leafId>




Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventorymodule <lcSlot> leafport <leafPort>


S Commandsshow faults leaf inventory module leafport

show faults leaf inventory powersupplyshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory powersupply <psuSlot>


Syntax:

Leaf id<leafId>



Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventorypowersupply <psuSlot>


S Commandsshow faults leaf inventory powersupply

show faults leaf inventory supervisorshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory supervisor <supMod>


Syntax:

Leaf id<leafId>



Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventorysupervisor <supMod>


S Commandsshow faults leaf inventory supervisor

show faults leaf protocolshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> protocol <protName>


Syntax:

Leaf id<leafId>



Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> protocol<protName>


S Commandsshow faults leaf protocol

show faults leaf vpcshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> vpc <vpcPort>


Syntax:

Leaf id<leafId>



Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> vpc<vpcPort>


S Commandsshow faults leaf vpc

show faults leaf vrfshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> vrf <vrfPort>


Syntax:

Leaf id<leafId>



Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> vrf<vrfPort>


S Commandsshow faults leaf vrf

show faults microsoft domainshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] microsoft domain

Description: Show Microsoft domain information


Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] microsoft domain


S Commandsshow faults microsoft domain

show faults microsoft domain nameshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] microsoft domain name <WORD>

Description:Microsoft domain name

Syntax:

Microsoft domain nameWORD


Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] microsoft domain name<WORD>


S Commandsshow faults microsoft domain name

show faults microsoft domain name hypervshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] microsoft domain name <WORD> hyperv <WORD>

Description: Show Microsoft Hypervisor information

Syntax:


HyperV hostnameWORD


Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] microsoft domain name<WORD> hyperv <WORD>


S Commandsshow faults microsoft domain name hyperv

show faults microsoft domain name port-groupshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] microsoft domain name <WORD> port-group

Description: Show Microsoft port group information

Syntax:



Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] microsoft domain name<WORD> port-group


S Commandsshow faults microsoft domain name port-group

show faults microsoft domain name scvmmshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] microsoft domain name <WORD> scvmm <hostname|ip>

Description: Show Microsoft SCVMM information

Syntax:


SCVMM hostname or IP<hostname|ip>


Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] microsoft domain name<WORD> scvmm <hostname|ip>


S Commandsshow faults microsoft domain name scvmm

show faults microsoft domain name vmshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] microsoft domain name <WORD> vm

Description: Show Microsoft VM information

Syntax:



Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] microsoft domain name<WORD> vm


S Commandsshow faults microsoft domain name vm

show faults microsoft domain name vm nameshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] microsoft domain name <WORD> vm name <WORD>

Description: Show detailed Microsoft VM information

Syntax:


VM NameWORD


Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] microsoft domain name<WORD> vm name <WORD>


S Commandsshow faults microsoft domain name vm name

show faults spineshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId>


Syntax:

Leaf id<leafId>


Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId>


S Commandsshow faults spine

show faults spine interface ethernetshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interface ethernet <phyInt>


Syntax:

Leaf id<leafId>



Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interfaceethernet <phyInt>


S Commandsshow faults spine interface ethernet

show faults spine interface l3instanceshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interface l3instance <l3Inst>


Syntax:

Leaf id<leafId>



Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interfacel3instance <l3Inst>


S Commandsshow faults spine interface l3instance

show faults spine interface mgmtshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interface mgmt <mgmtPort>


Syntax:

Leaf id<leafId>



Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interfacemgmt <mgmtPort>


S Commandsshow faults spine interface mgmt

show faults spine interface tunnelshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interface tunnel <tunnelPort>


Syntax:

Leaf id<leafId>



Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interfacetunnel <tunnelPort>


S Commandsshow faults spine interface tunnel

show faults spine inventory chassisshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory chassis


Syntax:

Leaf id<leafId>


Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventorychassis


S Commandsshow faults spine inventory chassis

show faults spine inventory fabricshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory fabric <fcMod>


Syntax:

Leaf id<leafId>



Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventoryfabric <fcMod>


S Commandsshow faults spine inventory fabric

show faults spine inventory fansshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory fans <ftSlot>


Syntax:

Leaf id<leafId>



Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventoryfans <ftSlot>


S Commandsshow faults spine inventory fans

show faults spine inventory moduleshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory module <lcSlot>


Syntax:

Leaf id<leafId>



Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventorymodule <lcSlot>


S Commandsshow faults spine inventory module

show faults spine inventory module fabricportshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory module <lcSlot> fabricport <fabPort>


Syntax:

Leaf id<leafId>




Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventorymodule <lcSlot> fabricport <fabPort>


S Commandsshow faults spine inventory module fabricport

show faults spine inventory powersupplyshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory powersupply <psuSlot>


Syntax:

Leaf id<leafId>



Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventorypowersupply <psuSlot>


S Commandsshow faults spine inventory powersupply

show faults spine inventory supervisorshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory supervisor <supMod>


Syntax:

Leaf id<leafId>



Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventorysupervisor <supMod>


S Commandsshow faults spine inventory supervisor

show faults spine inventory systemshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory system <sysMod>


Syntax:

Leaf id<leafId>



Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventorysystem <sysMod>


S Commandsshow faults spine inventory system

show faults spine protocolshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> protocol <protName>


Syntax:

Leaf id<leafId>



Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> protocol<protName>


S Commandsshow faults spine protocol

show faults spine vrfshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> vrf <vrfPort>


Syntax:

Leaf id<leafId>



Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> vrf<vrfPort>


S Commandsshow faults spine vrf

show faults tenantshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD


Syntax:



Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD


S Commandsshow faults tenant

show faults tenant applicationshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD application WORD


Syntax:




Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD applicationWORD


S Commandsshow faults tenant application

show faults tenant application epgshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD application WORD epg WORD


Syntax:





Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD applicationWORD epg WORD


S Commandsshow faults tenant application epg

show faults tenant bridge-domainshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD


Syntax:




Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORDbridge-domain WORD


S Commandsshow faults tenant bridge-domain

show faults tenant bridge-domain detailshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD detail


Syntax:




Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORDbridge-domain WORD detail


S Commandsshow faults tenant bridge-domain detail

show faults tenant interface bridge-domainshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD


Syntax:




Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interfacebridge-domain WORD


S Commandsshow faults tenant interface bridge-domain

show faults tenant interface bridge-domain detailshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD detail


Syntax:




Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interfacebridge-domain WORD detail


S Commandsshow faults tenant interface bridge-domain detail

show faults tenant vrfshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD


Syntax:




Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD


S Commandsshow faults tenant vrf

show faults tenant vrf detailshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD detail


Syntax:




Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDdetail


S Commandsshow faults tenant vrf detail

show faults tenant vrf external-l3 bgpshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 bgp


Syntax:




Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDexternal-l3 bgp


S Commandsshow faults tenant vrf external-l3 bgp

show faults tenant vrf external-l3 bgp nodeshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 bgp node <101-4000>


Syntax:





Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDexternal-l3 bgp node <101-4000>


S Commandsshow faults tenant vrf external-l3 bgp node

show faults tenant vrf external-l3 eigrpshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 eigrp


Syntax:




Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDexternal-l3 eigrp


S Commandsshow faults tenant vrf external-l3 eigrp

show faults tenant vrf external-l3 eigrp detailshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 eigrp detail


Syntax:




Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDexternal-l3 eigrp detail


S Commandsshow faults tenant vrf external-l3 eigrp detail

show faults tenant vrf external-l3 epgshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName>


Syntax:





Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDexternal-l3 epg <epgName>


S Commandsshow faults tenant vrf external-l3 epg

show faults tenant vrf external-l3 epg detailshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName> detail


Syntax:





Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDexternal-l3 epg <epgName> detail


S Commandsshow faults tenant vrf external-l3 epg detail

show faults tenant vrf external-l3 epg nameshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName> name <epgName>


Syntax:






Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDexternal-l3 epg <epgName> name <epgName>


S Commandsshow faults tenant vrf external-l3 epg name

show faults tenant vrf external-l3 epg name detailshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName> name <epgName>detail


Syntax:






Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDexternal-l3 epg <epgName> name <epgName> detail


S Commandsshow faults tenant vrf external-l3 epg name detail

show faults tenant vrf external-l3 interfacesshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 interfaces


Syntax:




Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDexternal-l3 interfaces


S Commandsshow faults tenant vrf external-l3 interfaces

show faults tenant vrf external-l3 interfaces detailshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 interfaces detail


Syntax:




Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDexternal-l3 interfaces detail


S Commandsshow faults tenant vrf external-l3 interfaces detail

show faults tenant vrf external-l3 ospfshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 ospf


Syntax:




Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDexternal-l3 ospf


S Commandsshow faults tenant vrf external-l3 ospf

show faults tenant vrf external-l3 ospf detailshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 ospf detail


Syntax:




Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDexternal-l3 ospf detail


S Commandsshow faults tenant vrf external-l3 ospf detail

show faults tenant vrf external-l3 static-routeshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route


Syntax:




Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDexternal-l3 static-route


S Commandsshow faults tenant vrf external-l3 static-route

show faults tenant vrf external-l3 static-route detailshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route detail


Syntax:




Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDexternal-l3 static-route detail


S Commandsshow faults tenant vrf external-l3 static-route detail

show faults tenant vrf external-l3 static-route nodeshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route node


Syntax:





Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDexternal-l3 static-route node


S Commandsshow faults tenant vrf external-l3 static-route node

show faults tenant vrf external-l3 static-route node detailshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route node detail


Syntax:





Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDexternal-l3 static-route node detail


S Commandsshow faults tenant vrf external-l3 static-route node detail

show faults vmware domainshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain

Description: Show VMware domain information


Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain


S Commandsshow faults vmware domain

show faults vmware domain nameshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name <name>

Description: VMware domain name

Syntax:

VMware domain name<name>


Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name<name>


S Commandsshow faults vmware domain name

show faults vmware domain name epgshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name <name> epg

Description: Show VMware domain EPG details

Syntax:



Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name<name> epg


S Commandsshow faults vmware domain name epg

show faults vmware domain name esxshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name <name> esx <esx-ip>

Description: Show VMware ESX information

Syntax:


ESX IP<esx-ip>


Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name<name> esx <esx-ip>


S Commandsshow faults vmware domain name esx

show faults vmware domain name port-groupshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name <name> port-group

Description: Show VMware port group information

Syntax:



Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name<name> port-group


S Commandsshow faults vmware domain name port-group

show faults vmware domain name vcentershow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name <name> vcenter <hostname|ip>

Description: VMware vCenter ip or hostname

Syntax:


vCenter hostname or IP<hostname|ip>


Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name<name> vcenter <hostname|ip>


S Commandsshow faults vmware domain name vcenter

show faults vmware domain name vmshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name <name> vm

Description: Show VMware VM information

Syntax:



Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name<name> vm


S Commandsshow faults vmware domain name vm

show faults vmware domain name vm nameshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name <name> vm name <vm-name>

Description: Show detailed VMware VM information

Syntax:


VM Name<vm-name>


Command Path:

# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name<name> vm name <vm-name>


S Commandsshow faults vmware domain name vm name

show firmware repositoryshow firmware repository

Description: Show firmware images present in repository


Command Path:

# show firmware repository


S Commandsshow firmware repository

show firmware repository detailshow firmware repository detail

Description: Detailed repository information


Command Path:

# show firmware repository detail


S Commandsshow firmware repository detail

show firmware upgrade statusshow firmware upgrade status

Description: Upgrade status of all controllers and switches


Command Path:

# show firmware upgrade status


S Commandsshow firmware upgrade status

show firmware upgrade status controller-groupshow firmware upgrade status controller-group

Description: Controller-group upgrade status


Command Path:

# show firmware upgrade status controller-group


S Commandsshow firmware upgrade status controller-group

show firmware upgrade status controller-group detailshow firmware upgrade status controller-group detail

Description: Detailed upgrade status


Command Path:

# show firmware upgrade status controller-group detail


S Commandsshow firmware upgrade status controller-group detail

show firmware upgrade status detailshow firmware upgrade status detail

Description: Detailed upgrade status information


Command Path:

# show firmware upgrade status detail


S Commandsshow firmware upgrade status detail

show firmware upgrade status switch-groupshow firmware upgrade status switch-group <WORD>

Description: Switch-group upgrade status

Syntax:



Command Path:

# show firmware upgrade status switch-group <WORD>


S Commandsshow firmware upgrade status switch-group

show firmware upgrade status switch-group detailshow firmware upgrade status switch-group <WORD> detail

Description: Detailed upgrade status

Syntax:



Command Path:

# show firmware upgrade status switch-group <WORD> detail


S Commandsshow firmware upgrade status switch-group detail

show healthshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time end-time <YYYY-MM-DDTHR:MIN:SEC>] <scope>

Description: Show health score information

Syntax:

(Optional) Historical informationhistory

(Optional) Minimum change in health score percentage. Number rangefrom=-100 to=9999

min-change <percentage change>

(Optional) Maximum health score. Number range from=0 to=100max-hs <maximum health-score>

(Optional) Health activity in time intervalstart-time<YYYY-MM-DDTHR:MIN:SEC>

(Optional) Health activity in time intervalend-time<YYYY-MM-DDTHR:MIN:SEC>



Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time end-time <YYYY-MM-DDTHR:MIN:SEC>] <scope>


S Commandsshow health

show health l4l7-clustershow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] l4l7-cluster [tenant <Tenant Name>] [cluster <Device ClusterName>]


Syntax:




Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] l4l7-cluster [tenant <TenantName>] [cluster <Device Cluster Name>]


S Commandsshow health l4l7-cluster

show health l4l7-graphshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] l4l7-graph [tenant <Tenant Name>] [graph <Graph Name>]


Syntax:




Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] l4l7-graph [tenant <TenantName>] [graph <Graph Name>]


S Commandsshow health l4l7-graph

show health leafshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId>


Syntax:

Leaf id<leafId>


Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId>


S Commandsshow health leaf

show health leaf fexshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> fex <fexNum>


Syntax:

Leaf id<leafId>



Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> fex <fexNum>


S Commandsshow health leaf fex

show health leaf fex moduleshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> fex <fexNum> module <lcSlot>


Syntax:

Leaf id<leafId>




Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> fex <fexNum>module <lcSlot>


S Commandsshow health leaf fex module

show health leaf interface ethernetshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> interface ethernet <phyInt>


Syntax:

Leaf id<leafId>



Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> interface ethernet<phyInt>


S Commandsshow health leaf interface ethernet

show health leaf interface l3instanceshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> interface l3instance <l3Inst>


Syntax:

Leaf id<leafId>



Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> interface l3instance<l3Inst>


S Commandsshow health leaf interface l3instance

show health leaf interface mgmtshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> interface mgmt <mgmtPort>


Syntax:

Leaf id<leafId>



Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> interface mgmt<mgmtPort>


S Commandsshow health leaf interface mgmt

show health leaf interface portchannelshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> interface portchannel <portChan>


Syntax:

Leaf id<leafId>



Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> interfaceportchannel <portChan>


S Commandsshow health leaf interface portchannel

show health leaf interface tunnelshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> interface tunnel <tunnelPort>


Syntax:

Leaf id<leafId>



Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> interface tunnel<tunnelPort>


S Commandsshow health leaf interface tunnel

show health leaf inventory chassisshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> inventory chassis <ch>


Syntax:

Leaf id<leafId>

None<ch>


Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> inventory chassis<ch>


S Commandsshow health leaf inventory chassis

show health leaf inventory fansshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> inventory fans <ftSlot>


Syntax:

Leaf id<leafId>



Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> inventory fans<ftSlot>


S Commandsshow health leaf inventory fans

show health leaf inventory moduleshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> inventory module <lcSlot>


Syntax:

Leaf id<leafId>



Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> inventory module<lcSlot>


S Commandsshow health leaf inventory module

show health leaf inventory module fabricportshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> inventory module <lcSlot> fabricport <fabPort>


Syntax:

Leaf id<leafId>




Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> inventory module<lcSlot> fabricport <fabPort>


S Commandsshow health leaf inventory module fabricport

show health leaf inventory module leafportshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> inventory module <lcSlot> leafport <leafPort>


Syntax:

Leaf id<leafId>




Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> inventory module<lcSlot> leafport <leafPort>


S Commandsshow health leaf inventory module leafport

show health leaf inventory powersupplyshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> inventory powersupply <psuSlot>


Syntax:

Leaf id<leafId>



Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> inventorypowersupply <psuSlot>


S Commandsshow health leaf inventory powersupply

show health leaf inventory supervisorshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> inventory supervisor <supMod>


Syntax:

Leaf id<leafId>



Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> inventory supervisor<supMod>


S Commandsshow health leaf inventory supervisor

show health leaf protocolshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> protocol <protName>


Syntax:

Leaf id<leafId>



Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> protocol <protName>


S Commandsshow health leaf protocol

show health leaf vpcshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> vpc <vpcPort>


Syntax:

Leaf id<leafId>



Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> vpc <vpcPort>


S Commandsshow health leaf vpc

show health leaf vrfshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> vrf <vrfPort>


Syntax:

Leaf id<leafId>



Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> vrf <vrfPort>


S Commandsshow health leaf vrf

show health spineshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId>


Syntax:

Leaf id<leafId>


Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId>


S Commandsshow health spine

show health spine interface ethernetshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> interface ethernet <phyInt>


Syntax:

Leaf id<leafId>



Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> interface ethernet<phyInt>


S Commandsshow health spine interface ethernet

show health spine interface l3instanceshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> interface l3instance <l3Inst>


Syntax:

Leaf id<leafId>



Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> interfacel3instance <l3Inst>


S Commandsshow health spine interface l3instance

show health spine interface mgmtshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> interface mgmt <mgmtPort>


Syntax:

Leaf id<leafId>



Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> interface mgmt<mgmtPort>


S Commandsshow health spine interface mgmt

show health spine interface tunnelshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> interface tunnel <tunnelPort>


Syntax:

Leaf id<leafId>



Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> interface tunnel<tunnelPort>


S Commandsshow health spine interface tunnel

show health spine inventory chassisshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventory chassis


Syntax:

Leaf id<leafId>


Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventory chassis


S Commandsshow health spine inventory chassis

show health spine inventory fabricshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventory fabric <fcMod>


Syntax:

Leaf id<leafId>



Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventory fabric<fcMod>


S Commandsshow health spine inventory fabric

show health spine inventory fansshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventory fans <ftSlot>


Syntax:

Leaf id<leafId>



Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventory fans<ftSlot>


S Commandsshow health spine inventory fans

show health spine inventory moduleshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventory module <lcSlot>


Syntax:

Leaf id<leafId>



Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventory module<lcSlot>


S Commandsshow health spine inventory module

show health spine inventory module fabricportshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventory module <lcSlot> fabricport <fabPort>


Syntax:

Leaf id<leafId>




Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventory module<lcSlot> fabricport <fabPort>


S Commandsshow health spine inventory module fabricport

show health spine inventory powersupplyshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventory powersupply <psuSlot>


Syntax:

Leaf id<leafId>



Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventorypowersupply <psuSlot>


S Commandsshow health spine inventory powersupply

show health spine inventory supervisorshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventory supervisor <supMod>


Syntax:

Leaf id<leafId>



Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventorysupervisor <supMod>


S Commandsshow health spine inventory supervisor

show health spine inventory systemshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventory system <sysMod>


Syntax:

Leaf id<leafId>



Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventory system<sysMod>


S Commandsshow health spine inventory system

show health spine protocolshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> protocol <protName>


Syntax:

Leaf id<leafId>



Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> protocol <protName>


S Commandsshow health spine protocol

show health spine vrfshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> vrf <vrfPort>


Syntax:

Leaf id<leafId>



Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> vrf <vrfPort>


S Commandsshow health spine vrf

show health tenantshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD


Syntax:



Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD


S Commandsshow health tenant

show health tenant applicationshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD application WORD


Syntax:




Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD application WORD


S Commandsshow health tenant application

show health tenant application epgshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD application WORD epg WORD


Syntax:





Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD application WORDepg WORD


S Commandsshow health tenant application epg

show health tenant bridge-domainshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD bridge-domain WORD


Syntax:




Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD bridge-domain WORD


S Commandsshow health tenant bridge-domain

show health tenant bridge-domain detailshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD bridge-domain WORD detail


Syntax:




Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD bridge-domain WORDdetail


S Commandsshow health tenant bridge-domain detail

show health tenant interface bridge-domainshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD interface bridge-domain WORD


Syntax:




Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD interfacebridge-domain WORD


S Commandsshow health tenant interface bridge-domain

show health tenant interface bridge-domain detailshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD interface bridge-domain WORD detail


Syntax:




Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD interfacebridge-domain WORD detail


S Commandsshow health tenant interface bridge-domain detail

show health tenant vrfshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD


Syntax:




Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD


S Commandsshow health tenant vrf

show health tenant vrf detailshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD detail


Syntax:




Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD detail


S Commandsshow health tenant vrf detail

show health tenant vrf external-l3 bgpshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 bgp


Syntax:




Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3bgp


S Commandsshow health tenant vrf external-l3 bgp

show health tenant vrf external-l3 bgp nodeshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 bgp node <101-4000>


Syntax:





Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3bgp node <101-4000>


S Commandsshow health tenant vrf external-l3 bgp node

show health tenant vrf external-l3 eigrpshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 eigrp


Syntax:




Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3eigrp


S Commandsshow health tenant vrf external-l3 eigrp

show health tenant vrf external-l3 eigrp detailshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 eigrp detail


Syntax:




Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3eigrp detail


S Commandsshow health tenant vrf external-l3 eigrp detail

show health tenant vrf external-l3 epgshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 epg <epgName>


Syntax:





Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3epg <epgName>


S Commandsshow health tenant vrf external-l3 epg

show health tenant vrf external-l3 epg detailshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 epg <epgName> detail


Syntax:





Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3epg <epgName> detail


S Commandsshow health tenant vrf external-l3 epg detail

show health tenant vrf external-l3 epg nameshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 epg <epgName> name<epgName>


Syntax:






Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3epg <epgName> name <epgName>


S Commandsshow health tenant vrf external-l3 epg name

show health tenant vrf external-l3 epg name detailshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 epg <epgName> name<epgName> detail


Syntax:






Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3epg <epgName> name <epgName> detail


S Commandsshow health tenant vrf external-l3 epg name detail

show health tenant vrf external-l3 interfacesshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 interfaces


Syntax:




Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3interfaces


S Commandsshow health tenant vrf external-l3 interfaces

show health tenant vrf external-l3 interfaces detailshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 interfaces detail


Syntax:




Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3interfaces detail


S Commandsshow health tenant vrf external-l3 interfaces detail

show health tenant vrf external-l3 ospfshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 ospf


Syntax:




Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3ospf


S Commandsshow health tenant vrf external-l3 ospf

show health tenant vrf external-l3 ospf detailshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 ospf detail


Syntax:




Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3ospf detail


S Commandsshow health tenant vrf external-l3 ospf detail

show health tenant vrf external-l3 static-routeshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 static-route


Syntax:




Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3static-route


S Commandsshow health tenant vrf external-l3 static-route

show health tenant vrf external-l3 static-route detailshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 static-route detail


Syntax:




Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3static-route detail


S Commandsshow health tenant vrf external-l3 static-route detail

show health tenant vrf external-l3 static-route nodeshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 static-route node


Syntax:





Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3static-route node


S Commandsshow health tenant vrf external-l3 static-route node

show health tenant vrf external-l3 static-route node detailshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 static-route node detail


Syntax:





Command Path:

# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3static-route node detail


S Commandsshow health tenant vrf external-l3 static-route node detail

show inband-mgmtshow inband-mgmt

Description: show inband mgmt epgs on all the nodes


Command Path:

# show inband-mgmt


S Commandsshow inband-mgmt

show inband-mgmt controllershow inband-mgmt controller <controller-id> [epg <WORD>]

Description: show inband mgmt epgs on the controller

Syntax:

<controller-id>

(Optional) Epg Name of conusmer epgWORD


Command Path:

# show inband-mgmt controller <controller-id> [epg <WORD>]


S Commandsshow inband-mgmt controller

show inband-mgmt switchshow inband-mgmt switch <switch-id> [epg <WORD>]

Description: show inband mgmt epgs on the node

Syntax:

<switch-id>

(Optional) Epg NameWORD


Command Path:

# show inband-mgmt switch <switch-id> [epg <WORD>]


S Commandsshow inband-mgmt switch

show interface bridge-domainshow interface bridge-domain WORD


Syntax:



Command Path:

# show interface bridge-domain WORD


S Commandsshow interface bridge-domain

show interface bridge-domain detailshow interface bridge-domain WORD detail


Syntax:



Command Path:

# show interface bridge-domain WORD detail


S Commandsshow interface bridge-domain detail

show ip interface bridge-domainshow ip interface bridge-domain WORD


Syntax:



Command Path:

# show ip interface bridge-domain WORD


S Commandsshow ip interface bridge-domain

show ipv6 interface bridge-domainshow ipv6 interface bridge-domain WORD


Syntax:



Command Path:

# show ipv6 interface bridge-domain WORD


S Commandsshow ipv6 interface bridge-domain

show l4l7-clustershow l4l7-cluster [tenant <Tenant Name>] [cluster <Device Cluster Name>]


Syntax:




Command Path:

# show l4l7-cluster [tenant <Tenant Name>] [cluster <Device Cluster Name>]


S Commandsshow l4l7-cluster

show l4l7-graphshow l4l7-graph [tenant <Tenant Name>] [graph <Graph Name>]


Syntax:




Command Path:

# show l4l7-graph [tenant <Tenant Name>] [graph <Graph Name>]


S Commandsshow l4l7-graph

show l4l7-packageshow l4l7-package

Description: Show L4-L7 package information


Command Path:

# show l4l7-package


S Commandsshow l4l7-package

show ldap-servershow ldap-server

Description: Show LDAP server information


Command Path:

# show ldap-server


S Commandsshow ldap-server

show locator-ledshow locator-led status

Description: Show command for locator-led

Syntax:

locator-led statusstatus


Command Path:

# show locator-led status


S Commandsshow locator-led

show locator-led status leafshow locator-led status leaf

Description: Leaf to filter on

Syntax:

locator-led statusstatus



Command Path:

# show locator-led status leaf


S Commandsshow locator-led status leaf

show microsoft domainshow microsoft domain

Description: Show Microsoft domain information


Command Path:

# show microsoft domain


S Commandsshow microsoft domain

show microsoft domain nameshow microsoft domain name <WORD>

Description:Microsoft domain name

Syntax:



Command Path:

# show microsoft domain name <WORD>


S Commandsshow microsoft domain name

show microsoft domain name hypervshow microsoft domain name <WORD> hyperv <WORD>

Description: Show Microsoft Hypervisor information

Syntax:


HyperV hostnameWORD


Command Path:

# show microsoft domain name <WORD> hyperv <WORD>


S Commandsshow microsoft domain name hyperv

show microsoft domain name port-groupshow microsoft domain name <WORD> port-group

Description: Show Microsoft port group information

Syntax:



Command Path:

# show microsoft domain name <WORD> port-group


S Commandsshow microsoft domain name port-group

show microsoft domain name scvmmshow microsoft domain name <WORD> scvmm <hostname|ip>

Description: Show Microsoft SCVMM information

Syntax:


SCVMM hostname or IP<hostname|ip>


Command Path:

# show microsoft domain name <WORD> scvmm <hostname|ip>


S Commandsshow microsoft domain name scvmm

show microsoft domain name vmshow microsoft domain name <WORD> vm


Syntax:



Command Path:

# show microsoft domain name <WORD> vm


S Commandsshow microsoft domain name vm

show microsoft domain name vm nameshow microsoft domain name <WORD> vm name <WORD>

Description: Show detailed Microsoft VM information

Syntax:


VM NameWORD


Command Path:

# show microsoft domain name <WORD> vm name <WORD>


S Commandsshow microsoft domain name vm name

show microsoft vmshow microsoft vm [name <WORD>] [ip <A.B.C.D>] [mac <AA:BB:CC:DD:EE:FF>]


Syntax:

(Optional) Specify a VM nameWORD

(Optional) Specify a VM IP addressA.B.C.D

(Optional) Specify a VM MAC addressAA:BB:CC:DD:EE:FF


Command Path:

# show microsoft vm [name <WORD>] [ip <A.B.C.D>] [mac <AA:BB:CC:DD:EE:FF>]


S Commandsshow microsoft vm

show monitor accessshow monitor access session session_name

Description: Show monitor session for access interfaces

Syntax:

sessionsession

session namesession_name


Command Path:

# show monitor access session session_name


S Commandsshow monitor access

show monitor fabricshow monitor fabric session session_name

Description: Show monitor session for fabric interfaces

Syntax:

sessionsession



Command Path:

# show monitor fabric session session_name


S Commandsshow monitor fabric

show monitor tenantshow monitor tenant <tenant_name> session session_name

Description: Show monitor session for tenant

Syntax:

tenanttenant_name

sessionsession



Command Path:

# show monitor tenant <tenant_name> session session_name


S Commandsshow monitor tenant

show monitor virtualshow monitor virtual session WORD

Description: Show monitor session for virtual switches

Syntax:

sessionsession

Session nameWORD


Command Path:

# show monitor virtual session WORD


S Commandsshow monitor virtual

show ntpqshow ntpq

Description: Show ntpq information


Command Path:

# show ntpq


S Commandsshow ntpq

show oob-mgmtshow oob-mgmt

Description: Show Out of band Information


Command Path:

# show oob-mgmt


S Commandsshow oob-mgmt

show oob-mgmt controllershow oob-mgmt controller <controller-id> [epg <WORD>]

Description: show oob mgmt epgs on the controller, enter one

Syntax:

<controller-id>



Command Path:

# show oob-mgmt controller <controller-id> [epg <WORD>]


S Commandsshow oob-mgmt controller

show oob-mgmt switchshow oob-mgmt switch <switch-id> [epg <WORD>]

Description: show oob mgmt epgs on the node, enter one

Syntax:

<switch-id>



Command Path:

# show oob-mgmt switch <switch-id> [epg <WORD>]


S Commandsshow oob-mgmt switch

show policy-mapshow policy-map

Description: Show policy maps


Command Path:

# show policy-map


S Commandsshow policy-map

show policy-map type data-planeshow policy-map type data-plane infra WORD

Description: data-plane type policy-map(s)

Syntax:

Global data-plane policy-map(s)infra

data-plane type policy-map(s) (Max Size 64)WORD


Command Path:

# show policy-map type data-plane infra WORD


S Commandsshow policy-map type data-plane

show policy-map type qosshow policy-map type qos WORD

Description: QOS type policy-map(s)

Syntax:

QOS type policy-map(s) (Max Size 64)WORD


Command Path:

# show policy-map type qos WORD


S Commandsshow policy-map type qos

show port-channel leafshow port-channel leaf WORD <port-channel-list>

Description: show leaf port-channel info

Syntax:

Leaf Range or Leaf Name ListWORD

port channel names<port-channel-list>


Command Path:

# show port-channel leaf WORD <port-channel-list>


S Commandsshow port-channel leaf

show port-channel mapshow port-channel map <port-channel-list>

Description: show port-channel mapping

Syntax:



Command Path:

# show port-channel map <port-channel-list>


S Commandsshow port-channel map

show port-channel map leafshow port-channel map <port-channel-list> leaf WORD [fex <101-164>]

Description: leaf

Syntax:



(Optional) Fex ID<101-164>


Command Path:

# show port-channel map <port-channel-list> leaf WORD [fex <101-164>]


S Commandsshow port-channel map leaf

show radius-servershow radius-server

Description: Show RADIUS server information


Command Path:

# show radius-server


S Commandsshow radius-server

show resourceshow resource conflict encap-vlan

Description: resource

Syntax:

show resource conflicts in APICconflict

show resource conflicts of encap-vlan in APICencap-vlan


Command Path:

# show resource conflict encap-vlan


S Commandsshow resource

show resource conflict encap-vlan epgshow resource conflict encap-vlan epg <WORD>

Description: Epg Name

Syntax:



Epg NameWORD


Command Path:

# show resource conflict encap-vlan epg <WORD>


S Commandsshow resource conflict encap-vlan epg

show resource conflict encap-vlan epg nodeshow resource conflict encap-vlan epg <WORD> node <101-4000>

Description: Node ID

Syntax:



Epg NameWORD

Leaf ID<101-4000>


Command Path:

# show resource conflict encap-vlan epg <WORD> node <101-4000>


S Commandsshow resource conflict encap-vlan epg node

show roleshow role

Description: Show information about AAA Roles


Command Path:

# show role


S Commandsshow role

show running-configshow running-config [all] <scope>

Description: show running configuration

Syntax:

(Optional) show running-config with defaultsall



Command Path:

# show running-config [all] <scope>


S Commandsshow running-config

show sessionsshow sessions [id <log-id>] [action action<action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] <scope>

Description: Show session-log information

Syntax:

(Optional) Log ID<log-id>

(Optional) Object action indicatoraction<action-type>

(Optional) Name of user<user-name>

(Optional) Logs created in time interval. Number range from=1 to=59<num-minutes>

(Optional) Logs created in time interval. Number range from=1 to=23<num-hours>

(Optional) Logs created in time interval. Number range from=1 to=999<num-days>

(Optional) Logs created in time interval<YYYY-MM-DDTHR:MIN:SEC>

(Optional) Logs created in time intervalend-time<YYYY-MM-DDTHR:MIN:SEC>

(Optional) Detailed session-log information. Displays the action triggerthat shows why a login occurred.

detail



Command Path:

# show sessions [id <log-id>] [action action<action-type>] [user <user-name>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] <scope>


S Commandsshow sessions

show sessions controllershow sessions [id <log-id>] [action <action-type>] [user <user-name>] [last-hours <NUMBER>] [last-days<NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail]controller



Command Path:

# show sessions [id <log-id>] [action <action-type>] [user <user-name>] [last-hours <NUMBER>][last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>][detail] controller


S Commandsshow sessions controller

show sessions controller detailshow sessions [id <log-id>] [action <action-type>] [user <user-name>] [last-hours <NUMBER>] [last-days<NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail]controller detail [id <node-id>]


Syntax:



Command Path:

# show sessions [id <log-id>] [action <action-type>] [user <user-name>] [last-hours <NUMBER>][last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>][detail] controller detail [id <node-id>]


S Commandsshow sessions controller detail

show sessions leafshow sessions [id <log-id>] [action <action-type>] [user <user-name>] [last-hours <NUMBER>] [last-days<NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail]leaf <leafId>


Syntax:

Leaf id<leafId>


Command Path:

# show sessions [id <log-id>] [action <action-type>] [user <user-name>] [last-hours <NUMBER>][last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>][detail] leaf <leafId>


S Commandsshow sessions leaf

show sessions spineshow sessions [id <log-id>] [action <action-type>] [user <user-name>] [last-hours <NUMBER>] [last-days<NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail]spine <leafId>


Syntax:

Leaf id<leafId>


Command Path:

# show sessions [id <log-id>] [action <action-type>] [user <user-name>] [last-hours <NUMBER>][last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>][detail] spine <leafId>


S Commandsshow sessions spine

show snapshot activeshow snapshot active job

Description: Show command for active snapshot job

Syntax:

View active snapshot jobjob


Command Path:

# show snapshot active job


S Commandsshow snapshot active

show snapshot filesshow snapshot files

Description: Show command for snapshot files


Command Path:

# show snapshot files


S Commandsshow snapshot files

show snapshot jobsshow snapshot jobs

Description: Show command for snapshot jobs


Command Path:

# show snapshot jobs


S Commandsshow snapshot jobs

show snmpshow snmp [policy <policy>]

Description: Show snmp policy information

Syntax:

(Optional) SNMP policy namepolicy


Command Path:

# show snmp [policy <policy>]


S Commandsshow snmp

show snmp clientgroupsshow snmp [policy <policy>] clientgroups

Description: Show snmp client group policies

Syntax:



Command Path:

# show snmp [policy <policy>] clientgroups


S Commandsshow snmp clientgroups

show snmp communityshow snmp [policy <policy>] community

Description: Show snmp community information

Syntax:



Command Path:

# show snmp [policy <policy>] community


S Commandsshow snmp community

show snmp engineidshow snmp [policy <policy>] engineid

Description: Show snmp v3 engine-id

Syntax:



Command Path:

# show snmp [policy <policy>] engineid


S Commandsshow snmp engineid

show snmp hostsshow snmp [policy <policy>] hosts

Description: Show snmp trap hosts

Syntax:



Command Path:

# show snmp [policy <policy>] hosts


S Commandsshow snmp hosts

show snmp usersshow snmp [policy <policy>] users

Description: Show snmp v3 users

Syntax:



Command Path:

# show snmp [policy <policy>] users


S Commandsshow snmp users

show statsshow stats granularity <granularity-value> [history] [cumulative] tenant|leaf|spine

Description: Show statistics

Syntax:

Choose granularity valuegranularity

<granularity-value><granularity-value>

(Optional) historical stats informationhistory

(Optional) cumulative stats informationcumulative

command scopetenant

command scopeleaf

command scopespine


Command Path:

# show stats granularity <granularity-value> [history] [cumulative] tenant|leaf|spine


S Commandsshow stats

show stats granularity leafshow stats granularity <granularity-value> [history] [cumulative] leaf <leafId>


Syntax:

Leaf id<leafId>


Command Path:

# show stats granularity <granularity-value> [history] [cumulative] leaf <leafId>


S Commandsshow stats granularity leaf

show stats granularity leaf fexshow stats granularity <granularity-value> [history] [cumulative] leaf <leafId> fex <fexNum>


Syntax:

Leaf id<leafId>



Command Path:

# show stats granularity <granularity-value> [history] [cumulative] leaf <leafId> fex<fexNum>


S Commandsshow stats granularity leaf fex

show stats granularity leaf fex moduleshow stats granularity <granularity-value> [history] [cumulative] leaf <leafId> fex <fexNum> module <lcSlot>


Syntax:

Leaf id<leafId>




Command Path:

# show stats granularity <granularity-value> [history] [cumulative] leaf <leafId> fex<fexNum> module <lcSlot>


S Commandsshow stats granularity leaf fex module

show stats granularity leaf interface ethernetshow stats granularity <granularity-value> [history] [cumulative] leaf <leafId> interface ethernet <phyInt>


Syntax:

Leaf id<leafId>



Command Path:

# show stats granularity <granularity-value> [history] [cumulative] leaf <leafId> interfaceethernet <phyInt>


S Commandsshow stats granularity leaf interface ethernet

show stats granularity leaf interface mgmtshow stats granularity <granularity-value> [history] [cumulative] leaf <leafId> interface mgmt <mgmtPort>


Syntax:

Leaf id<leafId>



Command Path:

# show stats granularity <granularity-value> [history] [cumulative] leaf <leafId> interfacemgmt <mgmtPort>


S Commandsshow stats granularity leaf interface mgmt

show stats granularity leaf interface portchannelshow stats granularity <granularity-value> [history] [cumulative] leaf <leafId> interface portchannel <portChan>


Syntax:

Leaf id<leafId>



Command Path:

# show stats granularity <granularity-value> [history] [cumulative] leaf <leafId> interfaceportchannel <portChan>


S Commandsshow stats granularity leaf interface portchannel

show stats granularity leaf inventory fansshow stats granularity <granularity-value> [history] [cumulative] leaf <leafId> inventory fans <ftSlot>


Syntax:

Leaf id<leafId>



Command Path:

# show stats granularity <granularity-value> [history] [cumulative] leaf <leafId> inventoryfans <ftSlot>


S Commandsshow stats granularity leaf inventory fans

show stats granularity leaf inventory powersupplyshow stats granularity <granularity-value> [history] [cumulative] leaf <leafId> inventory powersupply <psuSlot>


Syntax:

Leaf id<leafId>



Command Path:

# show stats granularity <granularity-value> [history] [cumulative] leaf <leafId> inventorypowersupply <psuSlot>


S Commandsshow stats granularity leaf inventory powersupply

show stats granularity leaf inventory supervisorshow stats granularity <granularity-value> [history] [cumulative] leaf <leafId> inventory supervisor <supMod>


Syntax:

Leaf id<leafId>



Command Path:

# show stats granularity <granularity-value> [history] [cumulative] leaf <leafId> inventorysupervisor <supMod>


S Commandsshow stats granularity leaf inventory supervisor

show stats granularity spineshow stats granularity <granularity-value> [history] [cumulative] spine <leafId>


Syntax:

Leaf id<leafId>


Command Path:

# show stats granularity <granularity-value> [history] [cumulative] spine <leafId>


S Commandsshow stats granularity spine

show stats granularity spine interface ethernetshow stats granularity <granularity-value> [history] [cumulative] spine <leafId> interface ethernet <phyInt>


Syntax:

Leaf id<leafId>



Command Path:

# show stats granularity <granularity-value> [history] [cumulative] spine <leafId> interfaceethernet <phyInt>


S Commandsshow stats granularity spine interface ethernet

show stats granularity spine interface mgmtshow stats granularity <granularity-value> [history] [cumulative] spine <leafId> interface mgmt <mgmtPort>


Syntax:

Leaf id<leafId>



Command Path:

# show stats granularity <granularity-value> [history] [cumulative] spine <leafId> interfacemgmt <mgmtPort>


S Commandsshow stats granularity spine interface mgmt

show stats granularity spine inventory chassisshow stats granularity <granularity-value> [history] [cumulative] spine <leafId> inventory chassis


Syntax:

Leaf id<leafId>


Command Path:

# show stats granularity <granularity-value> [history] [cumulative] spine <leafId> inventorychassis


S Commandsshow stats granularity spine inventory chassis

show stats granularity spine inventory fabricshow stats granularity <granularity-value> [history] [cumulative] spine <leafId> inventory fabric <fcMod>


Syntax:

Leaf id<leafId>



Command Path:

# show stats granularity <granularity-value> [history] [cumulative] spine <leafId> inventoryfabric <fcMod>


S Commandsshow stats granularity spine inventory fabric

show stats granularity spine inventory fansshow stats granularity <granularity-value> [history] [cumulative] spine <leafId> inventory fans <ftSlot>


Syntax:

Leaf id<leafId>



Command Path:

# show stats granularity <granularity-value> [history] [cumulative] spine <leafId> inventoryfans <ftSlot>


S Commandsshow stats granularity spine inventory fans

show stats granularity spine inventory moduleshow stats granularity <granularity-value> [history] [cumulative] spine <leafId> inventory module <lcSlot>


Syntax:

Leaf id<leafId>



Command Path:

# show stats granularity <granularity-value> [history] [cumulative] spine <leafId> inventorymodule <lcSlot>


S Commandsshow stats granularity spine inventory module

show stats granularity spine inventory powersupplyshow stats granularity <granularity-value> [history] [cumulative] spine <leafId> inventory powersupply<psuSlot>


Syntax:

Leaf id<leafId>



Command Path:

# show stats granularity <granularity-value> [history] [cumulative] spine <leafId> inventorypowersupply <psuSlot>


S Commandsshow stats granularity spine inventory powersupply

show stats granularity spine inventory supervisorshow stats granularity <granularity-value> [history] [cumulative] spine <leafId> inventory supervisor <supMod>


Syntax:

Leaf id<leafId>



Command Path:

# show stats granularity <granularity-value> [history] [cumulative] spine <leafId> inventorysupervisor <supMod>


S Commandsshow stats granularity spine inventory supervisor

show stats granularity spine inventory systemshow stats granularity <granularity-value> [history] [cumulative] spine <leafId> inventory system <sysMod>


Syntax:

Leaf id<leafId>



Command Path:

# show stats granularity <granularity-value> [history] [cumulative] spine <leafId> inventorysystem <sysMod>


S Commandsshow stats granularity spine inventory system

show stats granularity tenantshow stats granularity <granularity-value> [history] [cumulative] tenant WORD


Syntax:



Command Path:

# show stats granularity <granularity-value> [history] [cumulative] tenant WORD


S Commandsshow stats granularity tenant

show stats granularity tenant applicationshow stats granularity <granularity-value> [history] [cumulative] tenant WORD application WORD


Syntax:




Command Path:

# show stats granularity <granularity-value> [history] [cumulative] tenant WORD applicationWORD


S Commandsshow stats granularity tenant application

show stats granularity tenant application epgshow stats granularity <granularity-value> [history] [cumulative] tenant WORD application WORD epg WORD


Syntax:





Command Path:

# show stats granularity <granularity-value> [history] [cumulative] tenant WORD applicationWORD epg WORD


S Commandsshow stats granularity tenant application epg

show switchshow switch

Description: Show switch information


Command Path:

# show switch


S Commandsshow switch

show switch detailshow switch detail [id <switch-id>]

Description: Show switch detailed information

Syntax:

(Optional) Optional switch id. Number range from=0to=9223372036854775807

switch-id


Command Path:

# show switch detail [id <switch-id>]


S Commandsshow switch detail

show tacacs-servershow tacacs-server

Description: Show tacacs server information


Command Path:

# show tacacs-server


S Commandsshow tacacs-server

show techsupport allshow techsupport all status

Description: Techsupport status for all

Syntax:

Statusstatus


Command Path:

# show techsupport all status


S Commandsshow techsupport all

show techsupport controllersshow techsupport controllers status

Description: Techsupport status for controllers

Syntax:

Statusstatus


Command Path:

# show techsupport controllers status


S Commandsshow techsupport controllers

show techsupport hostshow techsupport host <NUMBER> status

Description: Techsupport status for host

Syntax:

Specify the host Odev ID. Number range from=0to=9223372036854775807

<Odevid>

Statusstatus


Command Path:

# show techsupport host <NUMBER> status


S Commandsshow techsupport host

show techsupport switchshow techsupport switch switchId <switchId> status

Description: Techsupport status for switch

Syntax:

switch id 101-4000 or range(s): 101-103,104switchId <switchId>

Statusstatus


Command Path:

# show techsupport switch switchId <switchId> status


S Commandsshow techsupport switch

show tenantshow tenant WORD


Syntax:



Command Path:

# show tenant WORD


S Commandsshow tenant

show tenant access-listshow tenant WORD access-list WORD

Description: Show Access-list Information

Syntax:




Command Path:

# show tenant WORD access-list WORD


S Commandsshow tenant access-list

show tenant applicationshow tenant WORD application WORD


Syntax:




Command Path:

# show tenant WORD application WORD


S Commandsshow tenant application

show tenant application endpointsshow tenant WORD application WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>]


Syntax:










Command Path:

# show tenant WORD application WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>]


S Commandsshow tenant application endpoints

show tenant application endpoints leaf interface ethernetshow tenant WORD application WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interfaceethernet ethernet [<fex>/]<slot>/<port>


Syntax:










WORD



Command Path:

# show tenant WORD application WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf<WORD> interface ethernet ethernet [<fex>/]<slot>/<port>


S Commandsshow tenant application endpoints leaf interface ethernet

show tenant application endpoints leaf interface port-channelshow tenant WORD application WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interfaceport-channel <WORD> [fex <NUMBER>]


Syntax:










WORD




Command Path:

# show tenant WORD application WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf<WORD> interface port-channel <WORD> [fex <NUMBER>]


S Commandsshow tenant application endpoints leaf interface port-channel

show tenant application endpoints vpcshow tenant WORD application WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] vpc context <WORD><WORD> interface vpc <WORD> [fex <fex>]


Syntax:









VPC Contextcontext


WORD


WORD






Command Path:

# show tenant WORD application WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] vpccontext <WORD> <WORD> interface vpc <WORD> [fex <fex>]


S Commandsshow tenant application endpoints vpc

show tenant application epgshow tenant WORD application WORD epg WORD


Syntax:





Command Path:

# show tenant WORD application WORD epg WORD


S Commandsshow tenant application epg

show tenant application epg detailshow tenant WORD application WORD epg WORD detail


Syntax:





Command Path:

# show tenant WORD application WORD epg WORD detail


S Commandsshow tenant application epg detail

show tenant application epg endpointsshow tenant WORD application WORD epg WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>]


Syntax:











Command Path:

# show tenant WORD application WORD epg WORD endpoints [type <type>] [mac <E.E.EEE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6<A:B::C:D>]


S Commandsshow tenant application epg endpoints

show tenant application epg endpoints leaf interface ethernetshow tenant WORD application WORD epg WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interfaceethernet ethernet [<fex>/]<slot>/<port>


Syntax:











WORD



Command Path:

# show tenant WORD application WORD epg WORD endpoints [type <type>] [mac <E.E.EEE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6<A:B::C:D>] leaf <WORD> interface ethernet ethernet [<fex>/]<slot>/<port>


S Commandsshow tenant application epg endpoints leaf interface ethernet

show tenant application epg endpoints leaf interfaceport-channel

show tenant WORD application WORD epg WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interfaceport-channel <WORD> [fex <NUMBER>]


Syntax:











WORD




Command Path:

# show tenant WORD application WORD epg WORD endpoints [type <type>] [mac <E.E.EEE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6<A:B::C:D>] leaf <WORD> interface port-channel <WORD> [fex <NUMBER>]


S Commandsshow tenant application epg endpoints leaf interface port-channel

show tenant application epg endpoints vpcshow tenant WORD application WORD epg WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] vpc context <WORD><WORD> interface vpc <WORD> [fex <fex>]


Syntax:










VPC Contextcontext


WORD


WORD






Command Path:

# show tenant WORD application WORD epg WORD endpoints [type <type>] [mac <E.E.E


S Commandsshow tenant application epg endpoints vpc

EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6<A:B::C:D>] vpc context <WORD> <WORD> interface vpc <WORD> [fex <fex>]


S Commandsshow tenant application epg endpoints vpc

show tenant bridge-domainshow tenant WORD bridge-domain WORD


Syntax:




Command Path:

# show tenant WORD bridge-domain WORD


S Commandsshow tenant bridge-domain

show tenant bridge-domain detailshow tenant WORD bridge-domain WORD detail


Syntax:




Command Path:

# show tenant WORD bridge-domain WORD detail


S Commandsshow tenant bridge-domain detail

show tenant contract-typeshow tenant WORD contract-type WORD

Description: Show Contracts Information Based on Type

Syntax:


whitelist (permit) or blacklist(deny) or oob-mgmt type of contractWORD


Command Path:

# show tenant WORD contract-type WORD


S Commandsshow tenant contract-type

show tenant contractshow tenant WORD contract WORD

Description: Show Contracts Information

Syntax:




Command Path:

# show tenant WORD contract WORD


S Commandsshow tenant contract

show tenant detailshow tenant WORD detail

Description: Show detailed view of tenant

Syntax:



Command Path:

# show tenant WORD detail


S Commandsshow tenant detail

show tenant endpointsshow tenant WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE>] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>]


Syntax:









Command Path:

# show tenant WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>]


S Commandsshow tenant endpoints

show tenant endpoints leaf interface ethernetshow tenant WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE>] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interface ethernet ethernet[<fex>/]<slot>/<port>


Syntax:









WORD



Command Path:

# show tenant WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interfaceethernet ethernet [<fex>/]<slot>/<port>


S Commandsshow tenant endpoints leaf interface ethernet

show tenant endpoints leaf interface port-channelshow tenant WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE>] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interface port-channel <WORD> [fex<NUMBER>]


Syntax:









WORD




Command Path:

# show tenant WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interfaceport-channel <WORD> [fex <NUMBER>]


S Commandsshow tenant endpoints leaf interface port-channel

show tenant endpoints vpcshow tenant WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE>] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] vpc context <WORD> <WORD> interface vpc <WORD>[fex <fex>]


Syntax:








VPC Contextcontext


WORD


WORD






Command Path:

# show tenant WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] vpc context <WORD><WORD> interface vpc <WORD> [fex <fex>]


S Commandsshow tenant endpoints vpc

show tenant epgshow tenant WORD epg WORD


Syntax:




Command Path:

# show tenant WORD epg WORD


S Commandsshow tenant epg

show tenant epg detailshow tenant WORD epg WORD detail


Syntax:




Command Path:

# show tenant WORD epg WORD detail


S Commandsshow tenant epg detail

show tenant external-l2 epgshow tenant WORD external-l2 epg WORD


Syntax:


Name of the EPG to filter on (Max Size 64)WORD


Command Path:

# show tenant WORD external-l2 epg WORD


S Commandsshow tenant external-l2 epg

show tenant interface bridge-domainshow tenant WORD interface bridge-domain WORD


Syntax:




Command Path:

# show tenant WORD interface bridge-domain WORD


S Commandsshow tenant interface bridge-domain

show tenant interface bridge-domain detailshow tenant WORD interface bridge-domain WORD detail


Syntax:




Command Path:

# show tenant WORD interface bridge-domain WORD detail


S Commandsshow tenant interface bridge-domain detail

show tenant ip interface bridge-domainshow tenant WORD ip interface bridge-domain WORD

Description: Show command for IP properties on interface BD

Syntax:




Command Path:

# show tenant WORD ip interface bridge-domain WORD


S Commandsshow tenant ip interface bridge-domain

show tenant ipv6 interface bridge-domainshow tenant WORD ipv6 interface bridge-domain WORD

Description: Show command for IP properties on interface BD

Syntax:




Command Path:

# show tenant WORD ipv6 interface bridge-domain WORD


S Commandsshow tenant ipv6 interface bridge-domain

show tenant policy-mapshow tenant WORD policy-map

Description: Show policy maps

Syntax:



Command Path:

# show tenant WORD policy-map


S Commandsshow tenant policy-map

show tenant policy-map type data-planeshow tenant WORD policy-map type data-plane WORD

Description: data-plane type policy-map(s)

Syntax:


data-plane type policy-map(s) (Max Size 64)WORD


Command Path:

# show tenant WORD policy-map type data-plane WORD


S Commandsshow tenant policy-map type data-plane

show tenant policy-map type qosshow tenant WORD policy-map type qos WORD

Description: QOS type policy-map(s)

Syntax:


QOS type policy-map(s) (Max Size 64)WORD


Command Path:

# show tenant WORD policy-map type qos WORD


S Commandsshow tenant policy-map type qos

show tenant vrfshow tenant WORD vrf WORD


Syntax:




Command Path:

# show tenant WORD vrf WORD


S Commandsshow tenant vrf

show tenant vrf detailshow tenant WORD vrf WORD detail


Syntax:




Command Path:

# show tenant WORD vrf WORD detail


S Commandsshow tenant vrf detail

show tenant vrf external-l3 bgpshow tenant WORD vrf WORD external-l3 bgp


Syntax:




Command Path:

# show tenant WORD vrf WORD external-l3 bgp


S Commandsshow tenant vrf external-l3 bgp

show tenant vrf external-l3 bgp nodeshow tenant WORD vrf WORD external-l3 bgp node <101-4000>


Syntax:





Command Path:

# show tenant WORD vrf WORD external-l3 bgp node <101-4000>


S Commandsshow tenant vrf external-l3 bgp node

show tenant vrf external-l3 eigrpshow tenant WORD vrf WORD external-l3 eigrp


Syntax:




Command Path:

# show tenant WORD vrf WORD external-l3 eigrp


S Commandsshow tenant vrf external-l3 eigrp

show tenant vrf external-l3 eigrp detailshow tenant WORD vrf WORD external-l3 eigrp detail


Syntax:




Command Path:

# show tenant WORD vrf WORD external-l3 eigrp detail


S Commandsshow tenant vrf external-l3 eigrp detail

show tenant vrf external-l3 epgshow tenant WORD vrf WORD external-l3 epg <epgName>


Syntax:





Command Path:

# show tenant WORD vrf WORD external-l3 epg <epgName>


S Commandsshow tenant vrf external-l3 epg

show tenant vrf external-l3 epg detailshow tenant WORD vrf WORD external-l3 epg <epgName> detail


Syntax:





Command Path:

# show tenant WORD vrf WORD external-l3 epg <epgName> detail


S Commandsshow tenant vrf external-l3 epg detail

show tenant vrf external-l3 epg nameshow tenant WORD vrf WORD external-l3 epg <epgName> name <epgName>


Syntax:






Command Path:

# show tenant WORD vrf WORD external-l3 epg <epgName> name <epgName>


S Commandsshow tenant vrf external-l3 epg name

show tenant vrf external-l3 epg name detailshow tenant WORD vrf WORD external-l3 epg <epgName> name <epgName> detail


Syntax:






Command Path:

# show tenant WORD vrf WORD external-l3 epg <epgName> name <epgName> detail


S Commandsshow tenant vrf external-l3 epg name detail

show tenant vrf external-l3 interfacesshow tenant WORD vrf WORD external-l3 interfaces


Syntax:




Command Path:

# show tenant WORD vrf WORD external-l3 interfaces


S Commandsshow tenant vrf external-l3 interfaces

show tenant vrf external-l3 interfaces detailshow tenant WORD vrf WORD external-l3 interfaces detail


Syntax:




Command Path:

# show tenant WORD vrf WORD external-l3 interfaces detail


S Commandsshow tenant vrf external-l3 interfaces detail

show tenant vrf external-l3 ospfshow tenant WORD vrf WORD external-l3 ospf


Syntax:




Command Path:

# show tenant WORD vrf WORD external-l3 ospf


S Commandsshow tenant vrf external-l3 ospf

show tenant vrf external-l3 ospf detailshow tenant WORD vrf WORD external-l3 ospf detail


Syntax:




Command Path:

# show tenant WORD vrf WORD external-l3 ospf detail


S Commandsshow tenant vrf external-l3 ospf detail

show tenant vrf external-l3 route-mapshow tenant WORD vrf WORD external-l3 route-map [name <l3out name>]


Syntax:





Command Path:

# show tenant WORD vrf WORD external-l3 route-map [name <l3out name>]


S Commandsshow tenant vrf external-l3 route-map

show tenant vrf external-l3 route-map detailshow tenant WORD vrf WORD external-l3 route-map [name <l3out name>] detail

Description: Show external-l3 route-map in detail with operational status

Syntax:





Command Path:

# show tenant WORD vrf WORD external-l3 route-map [name <l3out name>] detail


S Commandsshow tenant vrf external-l3 route-map detail

show tenant vrf external-l3 static-routeshow tenant WORD vrf WORD external-l3 static-route


Syntax:




Command Path:

# show tenant WORD vrf WORD external-l3 static-route


S Commandsshow tenant vrf external-l3 static-route

show tenant vrf external-l3 static-route detailshow tenant WORD vrf WORD external-l3 static-route detail


Syntax:




Command Path:

# show tenant WORD vrf WORD external-l3 static-route detail


S Commandsshow tenant vrf external-l3 static-route detail

show tenant vrf external-l3 static-route nodeshow tenant WORD vrf WORD external-l3 static-route node


Syntax:





Command Path:

# show tenant WORD vrf WORD external-l3 static-route node


S Commandsshow tenant vrf external-l3 static-route node

show tenant vrf external-l3 static-route node detailshow tenant WORD vrf WORD external-l3 static-route node detail


Syntax:





Command Path:

# show tenant WORD vrf WORD external-l3 static-route node detail


S Commandsshow tenant vrf external-l3 static-route node detail

show troubleshoot epext sessionshow troubleshoot epext session <session_name>

Description: Show session

Syntax:



Command Path:

# show troubleshoot epext session <session_name>


S Commandsshow troubleshoot epext session

show troubleshoot epext session atomiccountershow troubleshoot epext session <session_name> atomiccounter

Description: Show atomic counters

Syntax:



Command Path:

# show troubleshoot epext session <session_name> atomiccounter


S Commandsshow troubleshoot epext session atomiccounter

show troubleshoot epext session auditshow troubleshoot epext session <session_name> audit

Description: Show audit

Syntax:



Command Path:

# show troubleshoot epext session <session_name> audit


S Commandsshow troubleshoot epext session audit

show troubleshoot epext session contractsshow troubleshoot epext session <session_name> contracts

Description: Show contracts

Syntax:



Command Path:

# show troubleshoot epext session <session_name> contracts


S Commandsshow troubleshoot epext session contracts

show troubleshoot epext session deploymentsshow troubleshoot epext session <session_name> deployments

Description: Show deployment changes

Syntax:



Command Path:

# show troubleshoot epext session <session_name> deployments


S Commandsshow troubleshoot epext session deployments

show troubleshoot epext session eventsshow troubleshoot epext session <session_name> events

Description: Show events

Syntax:



Command Path:

# show troubleshoot epext session <session_name> events


S Commandsshow troubleshoot epext session events

show troubleshoot epext session faultsshow troubleshoot epext session <session_name> faults

Description: Show faults

Syntax:



Command Path:

# show troubleshoot epext session <session_name> faults


S Commandsshow troubleshoot epext session faults

show troubleshoot epext session monitorshow troubleshoot epext session <session_name> monitor

Description: Show monitor

Syntax:



Command Path:

# show troubleshoot epext session <session_name> monitor


S Commandsshow troubleshoot epext session monitor

show troubleshoot epext session reportsshow troubleshoot epext session <session_name> reports

Description: Show reports

Syntax:



Command Path:

# show troubleshoot epext session <session_name> reports


S Commandsshow troubleshoot epext session reports

show troubleshoot epext session statisticsshow troubleshoot epext session <session_name> statistics


Syntax:



Command Path:

# show troubleshoot epext session <session_name> statistics


S Commandsshow troubleshoot epext session statistics

show troubleshoot epext session topologyshow troubleshoot epext session <session_name> topology

Description: Show topology

Syntax:



Command Path:

# show troubleshoot epext session <session_name> topology


S Commandsshow troubleshoot epext session topology

show troubleshoot epext session tracerouteshow troubleshoot epext session <session_name> traceroute

Description: Show traceroute

Syntax:



Command Path:

# show troubleshoot epext session <session_name> traceroute


S Commandsshow troubleshoot epext session traceroute

show troubleshoot epext sessionsshow troubleshoot epext sessions

Description: Show sessions


Command Path:

# show troubleshoot epext sessions


S Commandsshow troubleshoot epext sessions

show troubleshoot eptoep sessionshow troubleshoot eptoep session <session_name>

Description: Show session

Syntax:



Command Path:

# show troubleshoot eptoep session <session_name>


S Commandsshow troubleshoot eptoep session

show troubleshoot eptoep session atomiccountershow troubleshoot eptoep session <session_name> atomiccounter

Description: Show atomic counters

Syntax:



Command Path:

# show troubleshoot eptoep session <session_name> atomiccounter


S Commandsshow troubleshoot eptoep session atomiccounter

show troubleshoot eptoep session auditshow troubleshoot eptoep session <session_name> audit

Description: Show audit

Syntax:



Command Path:

# show troubleshoot eptoep session <session_name> audit


S Commandsshow troubleshoot eptoep session audit

show troubleshoot eptoep session contractsshow troubleshoot eptoep session <session_name> contracts

Description: Show contracts

Syntax:



Command Path:

# show troubleshoot eptoep session <session_name> contracts


S Commandsshow troubleshoot eptoep session contracts

show troubleshoot eptoep session deploymentsshow troubleshoot eptoep session <session_name> deployments

Description: Show deployment changes

Syntax:



Command Path:

# show troubleshoot eptoep session <session_name> deployments


S Commandsshow troubleshoot eptoep session deployments

show troubleshoot eptoep session eventsshow troubleshoot eptoep session <session_name> events

Description: Show events

Syntax:



Command Path:

# show troubleshoot eptoep session <session_name> events


S Commandsshow troubleshoot eptoep session events

show troubleshoot eptoep session faultsshow troubleshoot eptoep session <session_name> faults

Description: Show faults

Syntax:



Command Path:

# show troubleshoot eptoep session <session_name> faults


S Commandsshow troubleshoot eptoep session faults

show troubleshoot eptoep session monitorshow troubleshoot eptoep session <session_name> monitor

Description: Show monitor

Syntax:



Command Path:

# show troubleshoot eptoep session <session_name> monitor


S Commandsshow troubleshoot eptoep session monitor

show troubleshoot eptoep session reportsshow troubleshoot eptoep session <session_name> reports

Description: Show reports

Syntax:



Command Path:

# show troubleshoot eptoep session <session_name> reports


S Commandsshow troubleshoot eptoep session reports

show troubleshoot eptoep session statisticsshow troubleshoot eptoep session <session_name> statistics


Syntax:



Command Path:

# show troubleshoot eptoep session <session_name> statistics


S Commandsshow troubleshoot eptoep session statistics

show troubleshoot eptoep session topologyshow troubleshoot eptoep session <session_name> topology

Description: Show topology

Syntax:



Command Path:

# show troubleshoot eptoep session <session_name> topology


S Commandsshow troubleshoot eptoep session topology

show troubleshoot eptoep session tracerouteshow troubleshoot eptoep session <session_name> traceroute

Description: Show traceroute

Syntax:



Command Path:

# show troubleshoot eptoep session <session_name> traceroute


S Commandsshow troubleshoot eptoep session traceroute

show troubleshoot eptoep sessionsshow troubleshoot eptoep sessions

Description: Show sessions


Command Path:

# show troubleshoot eptoep sessions


S Commandsshow troubleshoot eptoep sessions

show usernameshow username <WORD>

Description: Show user information

Syntax:

User nameWORD


Command Path:

# show username <WORD>


S Commandsshow username

show username detailshow username <WORD> detail

Description: Show user information

Syntax:

User nameWORD


Command Path:

# show username <WORD> detail


S Commandsshow username detail

show versionshow version

Description: Show version information


Command Path:

# show version


S Commandsshow version

show vlan-domainshow vlan-domain [name <arg>] [vlan] [leaf <arg>] [detail]

Description: Show command for vlan-domain

Syntax:

(Optional) Vlan-domain namearg

(Optional) VLAN ID 1-4094 or range(s): 1-5, 10 or 2-5,7-19<vlan-range>

(Optional) Leaf id. Number range from=101 to=4000arg

(Optional) vlan-domain in detail with concrete MOsdetail


Command Path:

# show vlan-domain [name <>] [vlan] [leaf <>] [detail]


S Commandsshow vlan-domain

show vmware domainshow vmware domain

Description: Show VMware domain information


Command Path:

# show vmware domain


S Commandsshow vmware domain

show vmware domain nameshow vmware domain name <name>

Description: VMware domain name

Syntax:



Command Path:

# show vmware domain name <name>


S Commandsshow vmware domain name

show vmware domain name epgshow vmware domain name <name> epg

Description: Show VMware domain EPG details

Syntax:



Command Path:

# show vmware domain name <name> epg


S Commandsshow vmware domain name epg

show vmware domain name esxshow vmware domain name <name> esx <esx-ip>

Description: Show VMware ESX information

Syntax:


ESX IP<esx-ip>


Command Path:

# show vmware domain name <name> esx <esx-ip>


S Commandsshow vmware domain name esx

show vmware domain name port-groupshow vmware domain name <name> port-group

Description: Show VMware port group information

Syntax:



Command Path:

# show vmware domain name <name> port-group


S Commandsshow vmware domain name port-group

show vmware domain name vcentershow vmware domain name <name> vcenter <hostname|ip>

Description: VMware vCenter ip or hostname

Syntax:


vCenter hostname or IP<hostname|ip>


Command Path:

# show vmware domain name <name> vcenter <hostname|ip>


S Commandsshow vmware domain name vcenter

show vmware domain name vmshow vmware domain name <name> vm


Syntax:



Command Path:

# show vmware domain name <name> vm


S Commandsshow vmware domain name vm

show vmware domain name vm nameshow vmware domain name <name> vm name <vm-name>

Description: Show detailed VMware VM information

Syntax:


VM Name<vm-name>


Command Path:

# show vmware domain name <name> vm name <vm-name>


S Commandsshow vmware domain name vm name

show vmware vmshow vmware vm [name <WORD>] [ip <A.B.C.D>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE >]


Syntax:

(Optional) Specify a VM nameWORD





Command Path:

# show vmware vm [name <WORD>] [ip <A.B.C.D>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE >]


S Commandsshow vmware vm

show vpcshow vpc map <vpc-list>

Description: show vpc mapping

Syntax:

map by namemap

vpc names<vpc-list>


Command Path:

# show vpc map <vpc-list>


S Commandsshow vpc

show vpc map leafshow vpc map <vpc-list> leaf WORD [fex <NUMBER>]

Description: leaf

Syntax:

map by namemap

vpc names<vpc-list>


(Optional) Fex ID. Number range from=101 to=164<101-164>


Command Path:

# show vpc map <vpc-list> leaf WORD [fex <NUMBER>]


S Commandsshow vpc map leaf

show vrfshow vrf WORD


Syntax:



Command Path:

# show vrf WORD


S Commandsshow vrf

show vrf detailshow vrf WORD detail


Syntax:



Command Path:

# show vrf WORD detail


S Commandsshow vrf detail

shutshut

Description: Disable BFD


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template bfd <WORD> tenant <WORD>(config-template-bfd-pol)# shut

shut

Description: Disable monitor session


Command Path:

# configure [['terminal', 't']](config)# monitor virtual session <WORD>(config-monitor-virtual)# shut


S Commandsshut

shutdownshutdown

Description: Administrative state of the Policer


Command Path:

# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>(config-pmap-dpp)# shutdown

shutdown

Description: Disable the class of service specified


Command Path:

# configure [['terminal', 't']](config)# qos parameters level1|level2|level3(config-qos)# shutdown

shutdown

Description: Administrative state of the Policer


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>(config-tenant-pmap-dpp)# shutdown

shutdown

Description: Disable Interface


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# shutdown

shutdown

Description: Disable Port Channel



S Commandsshutdown

Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# shutdown

shutdown

Description: Disable interface


Command Path:

# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# shutdown

shutdown



Command Path:

# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# shutdown

shutdown



Command Path:

# configure [['terminal', 't']](config)# monitor fabric session <session_name>(config-monitor-fabric)# shutdown

shutdown



Command Path:

# configure [['terminal', 't']](config)# monitor tenant <tenant_name> session <session_name>(config-monitor-tenant)# shutdown


S Commandsshutdown

site-idsite-id <WORD>

Description: ID of the network where the site is deployed

Syntax:

The site id (Max Size 512) surrounded by quotesWORD


Command Path:

# configure [['terminal', 't']](config)# callhome common(config-callhome)# destination-profile(config-callhome-destnprof)# site-id <WORD>


S Commandssite-id

slow-timerslow-timer <NUMBER>

Description: Configure BFD SLOW-TIMER value in milliseconds

Syntax:



Command Path:

# configure [['terminal', 't']](config)# template bfd ip|ipv6 <WORD>(config-bfd)# slow-timer <NUMBER>


S Commandsslow-timer

snapshot downloadsnapshot download <WORD>

Description: Configuration snapshot download setup mode

Syntax:

Snapshot downloader nameWORD


Command Path:

# configure [['terminal', 't']](config)# snapshot download <WORD>


S Commandssnapshot download

snapshot exportsnapshot export <WORD>

Description: Configuration export setup mode

Syntax:

Export configuration nameWORD


Command Path:

# configure [['terminal', 't']](config)# snapshot export <WORD>


S Commandssnapshot export

snapshot importsnapshot import <WORD>

Description: Configuration import setup mode

Syntax:

Import configuration nameWORD


Command Path:

# configure [['terminal', 't']](config)# snapshot import <WORD>


S Commandssnapshot import

snapshot rollbacksnapshot rollback <WORD>

Description: Configuration rollback setup mode

Syntax:

Rollback configuration nameWORD


Command Path:

# configure [['terminal', 't']](config)# snapshot rollback <WORD>


S Commandssnapshot rollback

snapshot uploadsnapshot upload <WORD>

Description: Configuration snapshot upload setup mode

Syntax:

Snapshot uploader nameWORD


Command Path:

# configure [['terminal', 't']](config)# snapshot upload <WORD>


S Commandssnapshot upload

snmp-server clientgroupsnmp-server clientgroup <group-name> [management-epg <mgmt-epg>] [client <ip-address/hostname>]

Description: Configure SNMP client-group

Syntax:

SNMP clientgroup<group-name>

(Optional) Management EPG (default: oob-default)<mgmt-epg>

(Optional) Ip-address/hostname of the snmp client<ip-address/hostname>


Command Path:

# configure [['terminal', 't']](config)# pod 1(config-pod)# snmp-server clientgroup <group-name> [management-epg <mgmt-epg>] [client<ip-address/hostname>]


S Commandssnmp-server clientgroup

snmp-server communitysnmp-server community <community-name>

Description: Configure SNMP community

Syntax:

SNMP community<community-name>


Command Path:

# configure [['terminal', 't']](config)# pod 1(config-pod)# snmp-server community <community-name>


S Commandssnmp-server community

snmp-server contactsnmp-server contact <contact-name>

Description: Configure SNMP contact

Syntax:

SNMP contact name<contact-name>


Command Path:

# configure [['terminal', 't']](config)# pod 1(config-pod)# snmp-server contact <contact-name>


S Commandssnmp-server contact

snmp-server hostsnmp-server host <ip-address/hostname> traps-version 1|2c|3 <community> auth|none|priv [udp-port <port>][management-epg <mgmt-epg>]

Description: Configure SNMP trap host

Syntax:

Ip-address/hostname of the snmp trap destination<ip-address/hostname>

SNMP Version to use for trapstraps-version

Use SNMPv11

Use SNMPv22c

Use SNMPv33

SNMP community/security<community>

Use Authentication Onlyauth

Use No Authenticationnone

Use Authentication and Encryptionpriv

(Optional) UDP port for traps (default 162)<port>

(Optional) Management EPG (default: oob-default)<mgmt-epg>


Command Path:

# configure [['terminal', 't']](config)# pod 1(config-pod)# snmp-server host <ip-address/hostname> traps-version 1|2c|3 <community>auth|none|priv [udp-port <port>] [management-epg <mgmt-epg>]


S Commandssnmp-server host

snmp-server locationsnmp-server location <location-name>

Description: Configure SNMP location

Syntax:

SNMP location<location-name>


Command Path:

# configure [['terminal', 't']](config)# pod 1(config-pod)# snmp-server location <location-name>


S Commandssnmp-server location

snmp-server protocolsnmp-server protocol enable

Description: Enable SNMP protocol

Syntax:

Enable SNMP protocolenable


Command Path:

# configure [['terminal', 't']](config)# pod 1(config-pod)# snmp-server protocol enable


S Commandssnmp-server protocol

snmp-server usersnmp-server user <user-name> auth sha|md5 <auth-key> priv aes|des|none [privacy-passphrase <priv-key>]

Description: Configure SNMP user

Syntax:

SNMP user<user-name>

Authentication Typeauth

Use HMAC SHA algorithm for authenticationsha

Use HMAC MD5 algorithm for authenticationmd5

Authentication password for user (Min Size 8, Max Size 130)<auth-key>

Privacy Typepriv

Use 128-bit AES algorithm for privacyaes

Use 64-bit DES algorithm for privacydes

Do not use privacynone

(Optional) Privacy passphrase for user (Min Size 8, Max Size 130)<priv-key>


Command Path:

# configure [['terminal', 't']](config)# pod 1(config-pod)# snmp-server user <user-name> auth sha|md5 <auth-key> priv aes|des|none[privacy-passphrase <priv-key>]


S Commandssnmp-server user

sourcesource tenant <WORD> application <WORD> epg <WORD> [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE >]

Description: Configure monitor virtual source

Syntax:

tenanttenant



application name (Max Size 64)WORD

epgepg

epg name (Max Size 64)WORD




Command Path:

# configure [['terminal', 't']](config)# monitor virtual session <WORD>(config-monitor-virtual)# source tenant <WORD> application <WORD> epg <WORD> [mac <E.E.EEE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >]


S Commandssource

source applicationsource application <application_name> epg <epg_name>

Description: Configure EPG as monitor source

Syntax:


epgepg



Command Path:

# configure [['terminal', 't']](config)# monitor tenant <tenant_name> session <session_name>(config-monitor-tenant)# source application <application_name> epg <epg_name>


S Commandssource application

source interface ethernetsource interface ethernet <ethernet> leaf <leaf Id>

Description: Configure monitor for ethernet access interfaces

Syntax:

List of ethernet itfs<ethernet>

leafleaf

leaf Id<leaf Id>


Command Path:

# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# source interface ethernet <ethernet> leaf <leaf Id>

source interface ethernet <ethernet> switch <switch Id>

Description: Configure monitor for ethernet fabric interfaces

Syntax:

ethernet interface range<ethernet>

switchswitch

switch Id<switch Id>


Command Path:

# configure [['terminal', 't']](config)# monitor fabric session <session_name>(config-monitor-fabric)# source interface ethernet <ethernet> switch <switch Id>


S Commandssource interface ethernet

source interface port-channelsource interface port-channel <port-channel list> leaf <leaf Id> [fex <fex Id>]

Description: Configure monitor for port-channel interfaces

Syntax:

<port-channel list><port-channel list>

leafleaf

leaf Id<leaf Id>

(Optional) fex Id<fex Id>


Command Path:

# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# source interface port-channel <port-channel list> leaf <leaf Id>[fex <fex Id>]


S Commandssource interface port-channel

source interface vpcsource interface vpc <vpc list> leaf <leaf Id1> <leaf Id2> [fex <fex Ids>]

Description: Configure monitor for VPC interfaces

Syntax:

<vpc list><vpc list>

leafleaf

leaf Id1<leaf Id1>

leaf Id2<leaf Id2>

(Optional) paired fex Ids<fex Ids>


Command Path:

# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# source interface vpc <vpc list> leaf <leaf Id1> <leaf Id2> [fex<fex Ids>]


S Commandssource interface vpc

spanning-treespanning-tree mst configuration

Description: STP MST configuration mode

Syntax:

Multiple spanning treemst

Configure multiple spanning tree protocolconfiguration


Command Path:

# configure [['terminal', 't']](config)# spanning-tree mst configuration

spanning-tree

Description: Add spanning tree

Command Mode: template leaf-policy-group : Configure Leaf Policy Group

Command Path:

# configure [['terminal', 't']](config)# template leaf-policy-group <WORD>(config-leaf-policy-group)# spanning-tree

spanning-tree bpdu-filter|bpdu-guard <enable|disable>

Description: Enable or Disable BPDU filter/guard

Syntax:

Don't send or receive BPDUs on this interfacebpdu-filter

Don't accept BPDUs on this interfacebpdu-guard

enable/disable BPDU filter/guard<enable|disable>


Command Path:

# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# spanning-tree bpdu-filter|bpdu-guard <enable|disable>


S Commandsspanning-tree


Description: enable BPDU filter/guard

Syntax:





Command Path:

# configure [['terminal', 't']](config)# template port-channel <WORD>(config-if)# spanning-tree bpdu-filter|bpdu-guard <enable|disable>


Description: Enable or disable BPDU filter/guard

Syntax:





Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# spanning-tree bpdu-filter|bpdu-guard <enable|disable>


Description: enable BPDU filter/guard

Syntax:







Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# spanning-tree bpdu-filter|bpdu-guard <enable|disable>


Description: Spanning Tree Subsystem

Syntax:





Command Path:

# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# spanning-tree bpdu-filter|bpdu-guard <enable|disable>



spanning-tree bpdu-filterspanning-tree bpdu-filter enable|disable|default

Description: Configure BPDU filter override on AVS uplink ports

Syntax:

Enable BPDU filterenable

Disable BPDU filterdisable

Remove BPDU filter/guard override policydefault


Command Path:

# configure [['terminal', 't']](config)# vmware-domain <WORD>(config-vmware)# configure-avs(config-vmware-avs)# spanning-tree bpdu-filter enable|disable|default


S Commandsspanning-tree bpdu-filter

spanning-tree bpdu-guardspanning-tree bpdu-guard enable|disable|default

Description: Configure BPDU guard override on AVS uplink ports

Syntax:

Enable BPDU guardenable

Disable BPDU guarddisable

Remove BPDU filter/guard override policydefault


Command Path:

# configure [['terminal', 't']](config)# vmware-domain <WORD>(config-vmware)# configure-avs(config-vmware-avs)# spanning-tree bpdu-guard enable|disable|default


S Commandsspanning-tree bpdu-guard

speedspeed <interfaceSpeed>

Description: Configure Interface Speed

Syntax:

Interface Speed Policy<interfaceSpeed>


Command Path:

# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# speed <interfaceSpeed>

speed <portChannelSpeed>


Syntax:

Port-Channel Speed Policy<portChannelSpeed>


Command Path:

# configure [['terminal', 't']](config)# template port-channel <WORD>(config-if)# speed <portChannelSpeed>

speed <interfaceSpeed>


Syntax:

Interface Speed Policy<interfaceSpeed>


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# speed <interfaceSpeed>


S Commandsspeed

speed <speed>


Syntax:

Speed Value<speed>


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# speed <speed>

speed <speed>


Syntax:

Interface Speed Policy<speed>


Command Path:

# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# speed <speed>


S Commandsspeed

spf-intervalspf-interval level-1 <NUMBER> <50-120000> <50-120000>

Description: Set the ISIS SPF maximal wait interval

Syntax:

Level 1level-1

SPF maximum wait interval. Number range from=50 to=120000<50-120000>

Initial and secondary wait intervals (both values are required)<50-120000> <50-120000>


Command Path:

# configure [['terminal', 't']](config)# pod 1(config-pod)# isis fabric(config-pod-isis)# spf-interval level-1 <NUMBER> <50-120000> <50-120000>


S Commandsspf-interval

ssh-keyssh-key <WORD>

Description: Update ssh key for the user for ssh authentication

Syntax:

A name for SSH key (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# username <WORD>(config-username)# ssh-key <WORD>


S Commandsssh-key

ssh-servicessh-service

Description: SSH communication policy group


Command Path:

# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# ssh-service


S Commandsssh-service

ssl-protocolsssl-protocols <sslProtocols>

Description: Set the SSL protocol (comma separated values)

Syntax:

SSL Protocols as comma separated values like val1,val2,..valNsslProtocols


Command Path:

# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# https(config-https)# ssl-protocols <sslProtocols>


S Commandsssl-protocols

ssl-validation-levelssl-validation-level <ssl-validation-level>

Description: Set the LDAP Server SSL Certificate validation level

Syntax:

<ssl-validation-level><ssl-validation-level>


Command Path:

# configure [['terminal', 't']](config)# ldap-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# ssl-validation-level <ssl-validation-level>


S Commandsssl-validation-level

statestate <WORD>

Description: Set The state or province in which the organization is located.

Syntax:

state or province (Max Size 64)<WORD>


Command Path:

# configure [['terminal', 't']](config)# crypto keyring <WORD>(config-keyring)# csr(config-csr)# state <WORD>

state <cipherState>

Description: Cipher state

Syntax:

Cipher state as comma separated values like val1,val2,..valNcipherState

Command Mode: ciphers : HTTPS cipher suite

Command Path:

# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# https(config-https)# ciphers <WORD>(config-ciphers)# state <cipherState>


S Commandsstate

static-endpointstatic-endpoint mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE vlan <NUMBER> [ip<A1.B1.C1.D1,...,An.Bn.Cn.Dn>] [ipv6 <A1:B1::C1:D1,..,An:Bn::Cn:Dn>]

Description: Configure Silent Host behind a EPG with a Static Path Attachment

Syntax:

MAC addressmac





Encapsulation Vlanvlan


(Optional) List of IP addresses in format i.i.i.iA1.B1.C1.D1,...,An.Bn.Cn.Dn

(Optional) List of IPv6 address in format xxxx:xxxx, xxxx::xxA1:B1::C1:D1,..,An:Bn::Cn:Dn


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# static-endpoint mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEEvlan <NUMBER> [ip <A1.B1.C1.D1,...,An.Bn.Cn.Dn>] [ipv6 <A1:B1::C1:D1,..,An:Bn::Cn:Dn>]

static-endpoint mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE vlan <NUMBER> [ip<A1.B1.C1.D1,...,An.Bn.Cn.Dn>] [ipv6 <A1:B1::C1:D1,..,An:Bn::Cn:Dn>]

Description: Configure silent Host behind a EPG with a Static Path Attachment

Syntax:

MAC addressmac





S Commandsstatic-endpoint







Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# static-endpoint mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEEvlan <NUMBER> [ip <A1.B1.C1.D1,...,An.Bn.Cn.Dn>] [ipv6 <A1:B1::C1:D1,..,An:Bn::Cn:Dn>]

static-endpoint mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE vlan <NUMBER> [ip<A1.B1.C1.D1,...,An.Bn.Cn.Dn>] [ipv6 <A1:B1::C1:D1,..,An:Bn::Cn:Dn>]

Description: Configure silent Host behind a EPG with a Static Path Attachment

Syntax:

MAC addressmac










Command Path:

# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>]



(config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# static-endpoint mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEEvlan <NUMBER> [ip <A1.B1.C1.D1,...,An.Bn.Cn.Dn>] [ipv6 <A1:B1::C1:D1,..,An:Bn::Cn:Dn>]



static-tepstatic-tep mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE vlan <NUMBER> <A.B.C.D>

Description: Configure a static Tunnel Endpoint behind a EPG with a Static Path Attachment

Syntax:

MAC addressmac






VLAN range. Number range from=1 to=4094<1-4094>



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# static-tep mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEEvlan <NUMBER> <A.B.C.D>

static-tep mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE vlan <NUMBER> <A.B.C.D>


Syntax:

MAC addressmac







S Commandsstatic-tep




Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# static-tep mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEEvlan <NUMBER> <A.B.C.D>

static-tep mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE vlan <NUMBER> <A.B.C.D>


Syntax:

MAC addressmac









Command Path:

# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# static-tep mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEEvlan <NUMBER> <A.B.C.D>


S Commandsstatic-tep

statisticsstatistics enable

Description: Enable/disable stats collection on VCenter (DVS-only)

Syntax:

enableenable

Command Mode: vcenter : Configure a VCenter in the VMware domain

Command Path:

# configure [['terminal', 't']](config)# vmware-domain <WORD>(config-vmware)# vcenter <> datacenter <WORD> [dvs-version <>](config-vmware-vc)# statistics enable


S Commandsstatistics

storm-control levelstorm-control level <0-100> [burst-rate <0-100>]

Description: Configure Storm Control Level (bandwidth percentage) on the Interface

Syntax:

Rate of Bandwidth in Percentage<0-100>

(Optional) Max Rate of Bandwidth in Percentage<0-100>


Command Path:

# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# storm-control level <0-100> [burst-rate <0-100>]

storm-control level <0-100> [burst-rate <0-100>]


Syntax:




Command Path:

# configure [['terminal', 't']](config)# template port-channel <WORD>(config-if)# storm-control level <0-100> [burst-rate <0-100>]



Syntax:





S Commandsstorm-control level

Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# storm-control level <0-100> [burst-rate <0-100>]



Syntax:




Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# storm-control level <0-100> [burst-rate <0-100>]



Syntax:




Command Path:

# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# storm-control level <0-100> [burst-rate <0-100>]


S Commandsstorm-control level

storm-control ppsstorm-control pps <arg> burst-rate <arg>

Description: Configure Storm Control in packet per second on the Interface

Syntax:

Burst Rate in packets per second. Number range from=0 to=4882812arg

Max Burst Rate in packets per secondburst-rate

Max Burst Rate in packets per second. Number range from=0to=4882812

arg


Command Path:

# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# storm-control pps <> burst-rate <>

storm-control pps <arg> burst-rate <arg>


Syntax:




arg


Command Path:

# configure [['terminal', 't']](config)# template port-channel <WORD>(config-if)# storm-control pps <> burst-rate <>



Syntax:


S Commandsstorm-control pps




arg


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# storm-control pps <> burst-rate <>



Syntax:




arg


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# storm-control pps <> burst-rate <>



Syntax:




arg




Command Path:

# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# storm-control pps <> burst-rate <>



street-addressstreet-address <WORD>

Description: Street address of the site

Syntax:

The street address (Max Size 255) surrounded by quotesWORD


Command Path:

# configure [['terminal', 't']](config)# callhome common(config-callhome)# destination-profile(config-callhome-destnprof)# street-address <WORD>


S Commandsstreet-address

subjectsubject <WORD>

Description: Set The fully qualified domain name or DN of the requesting device.

Syntax:

FQDN or DN of device (Max Size 64)<WORD>


Command Path:

# configure [['terminal', 't']](config)# crypto keyring <WORD>(config-keyring)# csr(config-csr)# subject <WORD>

subject <WORD>

Description: Configuration a subject on the contract

Syntax:

Name of the contract subject (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# contract <WORD> [type <type>](config-tenant-contract)# subject <WORD>


S Commandssubject

summary-addresssummary-address <IP-PREFIX/LEN>

Description: Route summarization

Syntax:

Summarized ipIP-PREFIX/LEN


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# summary-address <IP-PREFIX/LEN>


S Commandssummary-address

switch-groupswitch-group <WORD>

Description: Create switch firmware upgrade policy

Syntax:



Command Path:

# configure [['terminal', 't']](config)# firmware(config-firmware)# switch-group <WORD>


S Commandsswitch-group

switchswitch

Description: Add switches to switch group

Syntax:

arg


Command Path:

# configure [['terminal', 't']](config)# firmware(config-firmware)# switch-group <WORD>(config-firmware-switch)# switch

switch

Description: Configure Leaf Node

Syntax:

arg


Command Path:

# configure [['terminal', 't']](config)# switch

switch

Description: Add switches to zone

Syntax:

arg


Command Path:

# configure [['terminal', 't']](config)# zones(config-zones)# zone <WORD>(config-zone)# switch


S Commandsswitch

switchingswitching mode vlan|vxlan|vxlan-ns

Description: Configure switching mode.

Syntax:

switching Modemode

VLAN/SW Modevlan

VXLAN/SW Modevxlan

VXLAN/HWModevxlan-ns


Command Path:

# configure [['terminal', 't']](config)# vmware-domain <WORD>(config-vmware)# configure-avs(config-vmware-avs)# switching mode vlan|vxlan|vxlan-ns


S Commandsswitching

switchportswitchport vlan scope local

Description: L2 configuration

Syntax:

vlan

scope

Local Scopelocal


Command Path:

# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# switchport vlan scope local

switchport vlan scope local


Syntax:

vlan

scope

Local Scopelocal


Command Path:

# configure [['terminal', 't']](config)# template port-channel <WORD>(config-if)# switchport vlan scope local

switchport

Description: Configure switchport parameters


Command Path:



S Commandsswitchport

(config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# switchport

switchport



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# switchport

switchport



Command Path:

# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# switchport


S Commandsswitchport

switchport access vlan tenant applicationswitchport access vlan <NUMBER> tenant <WORD> application <WORD> epg <WORD>

Description: Application Name

Syntax:

Access Vlanvlan

Access Vlan. Number range from=1 to=4094<1-4094>

Tenant hosting the AEPgtenant

Tenant hosting the AEPg (Max Size 63)WORD


EPg that uses the statically enabled Encapepg

EPg that uses the statically enabled Encap (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# switchport access vlan <NUMBER> tenant <WORD> application <WORD> epg<WORD>

switchport access vlan <NUMBER> tenant <WORD> application <WORD> epg <WORD>


Syntax:

Access Vlanvlan








S Commandsswitchport access vlan tenant application


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# switchport access vlan <NUMBER> tenant <WORD> application <WORD> epg<WORD>

switchport access vlan <NUMBER> tenant <WORD> application <WORD> epg <WORD>


Syntax:

Access Vlanvlan








Command Path:

# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# switchport access vlan <NUMBER> tenant <WORD> application <WORD> epg <WORD>


S Commandsswitchport access vlan tenant application

switchport access vlan tenant external-sviswitchport access vlan <NUMBER> tenant <WORD> external-svi [l3out] WORD

Description: Associate SVI to the L2 Access Interface

Syntax:

Access Vlanvlan




(Optional) Specify one or more l3extOut to add SVI interfacel3out

l3extOut NameWORD


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# switchport access vlan <NUMBER> tenant <WORD> external-svi [l3out] WORD

switchport access vlan <NUMBER> tenant <WORD> external-svi [l3out] WORD

Description: Associate SVI to Acess L2 Interface

Syntax:

Access Vlanvlan





l3extOut NameWORD



S Commandsswitchport access vlan tenant external-svi

Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# switchport access vlan <NUMBER> tenant <WORD> external-svi [l3out] WORD

switchport access vlan <NUMBER> tenant <WORD> external-svi [l3out] WORD

Description: Associate SVI to Acess L2 Interface

Syntax:

Access Vlanvlan





l3extOut NameWORD


Command Path:

# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# switchport access vlan <NUMBER> tenant <WORD> external-svi [l3out] WORD


S Commandsswitchport access vlan tenant external-svi

switchport trunk allowed vlan inband-mgmtswitchport trunk allowed vlan <NUMBER> inband-mgmt <A.B.C.D/LEN>

Description: Configure External L2 connectivity to inband Mnaagement

Syntax:



Gateway IP Address for External Connectivity format x.x.x.x/mA.B.C.D/LEN


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# switchport trunk allowed vlan <NUMBER> inband-mgmt <A.B.C.D/LEN>


S Commandsswitchport trunk allowed vlan inband-mgmt

switchport trunk allowed vlan tenant applicationswitchport trunk allowed vlan <NUMBER> tenant <WORD> application <WORD> epg <WORD> [primary-vlanprimary-vlan <evlan>]

Description: Add an AEPg as static encap

Syntax:



Tenant hosting the EPg (Max Size 63)WORD




(Optional) Vlan for egress traffic when EPG isolation is enforcedprimary-vlan <evlan>


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# switchport trunk allowed vlan <NUMBER> tenant <WORD> application <WORD>epg <WORD> [primary-vlan primary-vlan <evlan>]

switchport trunk allowed vlan <NUMBER> tenant <WORD> application <WORD> epg <WORD>


Syntax:



Tenant hosting the EPgtenant





S Commandsswitchport trunk allowed vlan tenant application



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# switchport trunk allowed vlan <NUMBER> tenant <WORD> application <WORD>epg <WORD>

switchport trunk allowed vlan <NUMBER> tenant <WORD> application <WORD> epg <WORD>


Syntax:









Command Path:

# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# switchport trunk allowed vlan <NUMBER> tenant <WORD> application <WORD>epg <WORD>


S Commandsswitchport trunk allowed vlan tenant application

switchport trunk allowed vlan tenant external-l2switchport trunk allowed vlan <NUMBER> tenant <WORD> external-l2 epg <WORD>

Description: Add a L2 external EPG on the interface

Syntax:







Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# switchport trunk allowed vlan <NUMBER> tenant <WORD> external-l2 epg<WORD>

switchport trunk allowed vlan <NUMBER> tenant <WORD> external-l2 epg <WORD>


Syntax:









S Commandsswitchport trunk allowed vlan tenant external-l2

Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# switchport trunk allowed vlan <NUMBER> tenant <WORD> external-l2 epg<WORD>

switchport trunk allowed vlan <NUMBER> tenant <WORD> external-l2 epg <WORD>


Syntax:








Command Path:

# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# switchport trunk allowed vlan <NUMBER> tenant <WORD> external-l2 epg <WORD>


S Commandsswitchport trunk allowed vlan tenant external-l2

switchport trunk allowed vlan tenant external-sviswitchport trunk allowed vlan <NUMBER> tenant <WORD> external-svi [l3out] WORD

Description: Associate SVI to the L2 Interface

Syntax:





l3extOut NameWORD


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# switchport trunk allowed vlan <NUMBER> tenant <WORD> external-svi [l3out]WORD

switchport trunk allowed vlan <NUMBER> tenant <WORD> external-svi [l3out] WORD


Syntax:






l3extOut NameWORD



S Commandsswitchport trunk allowed vlan tenant external-svi

Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# switchport trunk allowed vlan <NUMBER> tenant <WORD> external-svi [l3out]WORD

switchport trunk allowed vlan <NUMBER> tenant <WORD> external-svi [l3out] WORD


Syntax:






l3extOut NameWORD


Command Path:

# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# switchport trunk allowed vlan <NUMBER> tenant <WORD> external-svi [l3out]WORD


S Commandsswitchport trunk allowed vlan tenant external-svi

switchport trunk allowed vlan tenant legacy-forwardingswitchport trunk allowed vlan <NUMBER> tenant <WORD> legacy-forwarding

Description: Add legacy forwarding on the vlan supplied

Syntax:





Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# switchport trunk allowed vlan <NUMBER> tenant <WORD> legacy-forwarding

switchport trunk allowed vlan <NUMBER> tenant <WORD> legacy-forwarding


Syntax:






Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# switchport trunk allowed vlan <NUMBER> tenant <WORD> legacy-forwarding

switchport trunk allowed vlan <NUMBER> tenant <WORD> legacy-forwarding


Syntax:


S Commandsswitchport trunk allowed vlan tenant legacy-forwarding






Command Path:

# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# switchport trunk allowed vlan <NUMBER> tenant <WORD> legacy-forwarding


S Commandsswitchport trunk allowed vlan tenant legacy-forwarding

switchport trunk native vlan tenant applicationswitchport trunk native vlan <NUMBER> tenant <WORD> application <WORD> epg <WORD>

Description: Application hosting the AEPg

Syntax:

Native Vlanvlan

Native Vlan. Number range from=1 to=4094<1-4094>







Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# switchport trunk native vlan <NUMBER> tenant <WORD> application <WORD>epg <WORD>

switchport trunk native vlan <NUMBER> tenant <WORD> application <WORD> epg <WORD>


Syntax:

Native Vlanvlan








S Commandsswitchport trunk native vlan tenant application


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# switchport trunk native vlan <NUMBER> tenant <WORD> application <WORD>epg <WORD>

switchport trunk native vlan <NUMBER> tenant <WORD> application <WORD> epg <WORD>


Syntax:

Native Vlanvlan








Command Path:

# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# switchport trunk native vlan <NUMBER> tenant <WORD> application <WORD> epg<WORD>


S Commandsswitchport trunk native vlan tenant application

switchport trunk native vlan tenant external-sviswitchport trunk native vlan <NUMBER> tenant <WORD> external-svi [l3out] WORD

Description: Associate SVI to the L2 Trunk Interface

Syntax:

Native Vlanvlan





l3extOut NameWORD


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# switchport trunk native vlan <NUMBER> tenant <WORD> external-svi [l3out]WORD

switchport trunk native vlan <NUMBER> tenant <WORD> external-svi [l3out] WORD

Description: Associate Native Vlan to the L2 Trunk Interface as external SVI

Syntax:

Native Vlanvlan





l3extOut NameWORD



S Commandsswitchport trunk native vlan tenant external-svi

Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# switchport trunk native vlan <NUMBER> tenant <WORD> external-svi [l3out]WORD

switchport trunk native vlan <NUMBER> tenant <WORD> external-svi [l3out] WORD

Description: Associate SVI to Trunk L2 Interface

Syntax:

Native Vlanvlan





l3extOut NameWORD


Command Path:

# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# switchport trunk native vlan <NUMBER> tenant <WORD> external-svi [l3out]WORD


S Commandsswitchport trunk native vlan tenant external-svi

switchport vlanswitchport vlan scope local


Syntax:

scope

Local Scopelocal


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# switchport vlan scope local


Description:

Syntax:

scope

Local Scopelocal


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# switchport vlan scope local


Description:

Syntax:

scope

Local Scopelocal


S Commandsswitchport vlan


Command Path:

# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# switchport vlan scope local


S Commandsswitchport vlan

syslogsyslog common

Description: Syslog common policy configuration mode

Syntax:

Syslog common policy configuration modecommon


Command Path:

# configure [['terminal', 't']](config)# syslog common


S Commandssyslog

system cluster-sizesystem cluster-size <NUMBER>

Description: Set APIC cluster size

Syntax:

size of the cluster to be set. Number range from=1 to=16<size>


Command Path:

# configure [['terminal', 't']](config)# system cluster-size <NUMBER>


S Commandssystem cluster-size

system controller-idsystem controller-id <serial-number> approve|reject

Description: Configure Controller Id for controllers in fabric

Syntax:

Controller serial numberserial-number

Approve controllerapprove

Reject controllerreject


Command Path:

# configure [['terminal', 't']](config)# system controller-id <serial-number> approve|reject


S Commandssystem controller-id

system dynamic-load-balancesystem dynamic-load-balance modelink-failure-resiliency|dynamic-aggressive|dynamic-conservative|packet-prioritization

Description: Configure dynamic load balancer

Syntax:

Dynamic load balancer modemode

Link failure resiliency modelink-failure-resiliency

Aggressive dynamic modedynamic-aggressive

Conservative dynamic modedynamic-conservative

Packet prioritization modepacket-prioritization


Command Path:

# configure [['terminal', 't']](config)# system dynamic-load-balance modelink-failure-resiliency|dynamic-aggressive|dynamic-conservative|packet-prioritization


S Commandssystem dynamic-load-balance

system fabric-security-modesystem fabric-security-mode <mode>

Description: Set strict/permissive mode for ACI Fabric Internode Authentication

Syntax:

Security mode as comma separated values like val1,val2,..valN<mode>


Command Path:

# configure [['terminal', 't']](config)# system fabric-security-mode <mode>


S Commandssystem fabric-security-mode

system jumbomtusystem jumbomtu <NUMBER>

Description:MTU size for Host Facing ports

Syntax:

Enter jumbomtu. Number range from=576 to=9000<576-9000>


Command Path:

# configure [['terminal', 't']](config)# system jumbomtu <NUMBER>


S Commandssystem jumbomtu

system switch-idsystem switch-id <serial-number> <node-Id> <name>

Description: Configure Node Id for switches in fabric

Syntax:

Switch serial numberserial-number

Switch ID. Number range from=101 to=4000node-Id

Switch namename


Command Path:

# configure [['terminal', 't']](config)# system switch-id <serial-number> <node-Id> <name>


S Commandssystem switch-id

T Commands

• tacacs-server host, page 1327

• tacacs-server retries, page 1328

• tacacs-server timeout, page 1329

• tag, page 1330

• target, page 1332

• telnet, page 1333

• template bfd, page 1334

• template bgp address-family, page 1335

• template bgp timers, page 1336

• template community-list expanded, page 1337

• template community-list standard, page 1338

• template dhcp option, page 1339

• template dhcp relay, page 1340

• template eigrp interface-policy, page 1341

• template eigrp vrf-policy, page 1342

• template endpoint retention policy, page 1343

• template extcommunity-list expanded, page 1344

• template extcommunity-list standard, page 1345

• template ip igmp snooping policy, page 1346

• template ipv6 nd policy, page 1347

• template ipv6 nd prefix, page 1348

• template leaf-policy-group, page 1349

• template ospf interface-policy, page 1350

• template ospf vrf-policy, page 1351


• template policy-group, page 1352

• template port-channel, page 1353

• template route-profile, page 1354

• template route tag, page 1355

• tenant, page 1356

• terminal, page 1357

• time, page 1358

• time start daily, page 1359

• time start weekly, page 1360

• timeout, page 1361

• timers, page 1362

• timers lsa-arrival, page 1364

• timers lsa-group-pacing, page 1365

• timers throttle lsa, page 1366

• timers throttle spf, page 1367

• tp, page 1368

• transmit-delay, page 1369

• transport email from, page 1370

• transport email mail-server, page 1371

• transport email reply-to, page 1372

• trigger fabric-recovery, page 1373

• trigger shutdown, page 1374

• trigger snapshot download, page 1375

• trigger snapshot export, page 1376

• trigger snapshot import, page 1377

• trigger snapshot rollback, page 1378

• trigger snapshot upload, page 1379

• trigger techsupport all, page 1380

• trigger techsupport controllers, page 1381

• trigger techsupport host, page 1382

• trigger techsupport local, page 1383

• trigger techsupport switch, page 1384

• trigger troubleshoot epext session report, page 1385


T Commands

• trigger troubleshoot eptoep session report, page 1386

• trigger vmware, page 1387

• troubleshoot epext session atomiccounter, page 1388

• troubleshoot epext session description, page 1389

• troubleshoot epext session latestminutes, page 1390

• troubleshoot epext session monitor destination apic, page 1391

• troubleshoot epext session monitor destination prefdestgroup, page 1392

• troubleshoot epext session monitor destination tenant, page 1393

• troubleshoot epext session scheduler, page 1395

• troubleshoot epext session srcextip destip tenant application, page 1396

• troubleshoot epext session srcextip destip tenant vrf, page 1397

• troubleshoot epext session srcip tenant application epg destextip, page 1398

• troubleshoot epext session srcip tenant vrf destextip, page 1399

• troubleshoot epext session starttime, page 1400

• troubleshoot epext session traceroute, page 1401

• troubleshoot epext session traceroute protocol icmp, page 1402

• troubleshoot epext session traceroute protocol tcp, page 1403

• troubleshoot epext session traceroute protocol udp, page 1404

• troubleshoot eptoep session atomiccounter, page 1405

• troubleshoot eptoep session description, page 1406

• troubleshoot eptoep session latestminutes, page 1407

• troubleshoot eptoep session monitor destination apic, page 1408

• troubleshoot eptoep session monitor destination prefdestgroup, page 1409

• troubleshoot eptoep session monitor destination tenant, page 1410

• troubleshoot eptoep session scheduler, page 1412

• troubleshoot eptoep session srcip tenant application epg destip tenant application, page 1413

• troubleshoot eptoep session srcip tenant application epg destip tenant vrf, page 1414

• troubleshoot eptoep session srcip tenant vrf destip tenant application, page 1415

• troubleshoot eptoep session srcip tenant vrf destip tenant vrf, page 1416

• troubleshoot eptoep session srcmac tenant application epg destmac tenant application, page 1417

• troubleshoot eptoep session srcmac tenant application epg destmac tenant vrf, page 1419

• troubleshoot eptoep session srcmac tenant vrf destmac tenant application, page 1420

• troubleshoot eptoep session srcmac tenant vrf destmac tenant vrf, page 1421


T Commands

• troubleshoot eptoep session starttime, page 1422

• troubleshoot eptoep session traceroute, page 1423

• troubleshoot eptoep session traceroute protocol icmp, page 1424

• troubleshoot eptoep session traceroute protocol tcp, page 1425

• troubleshoot eptoep session traceroute protocol udp, page 1426

• trusted-key, page 1427


T Commands

tacacs-server hosttacacs-server host <A.B.C.D|A:B::C:D|WORD>

Description: TACACS+ server's DNS name or its IP address

Syntax:

TACACS+ server's DNS name or its IP addressA.B.C.D|A:B::C:D|WORD


Command Path:

# configure [['terminal', 't']](config)# tacacs-server host <A.B.C.D|A:B::C:D|WORD>


T Commandstacacs-server host

tacacs-server retriestacacs-server retries <NUMBER>

Description: Global TACACS+ server retries period in seconds

Syntax:

Global TACACS+ server retries period in seconds. Number rangefrom=0 to=5

<0-5>


Command Path:

# configure [['terminal', 't']](config)# tacacs-server retries <NUMBER>


T Commandstacacs-server retries

tacacs-server timeouttacacs-server timeout <NUMBER>

Description: Global TACACS+ server timeout period in seconds

Syntax:

Global TACACS+ server timeout period in seconds. Number rangefrom=1 to=60

<1-60>


Command Path:

# configure [['terminal', 't']](config)# tacacs-server timeout <NUMBER>


T Commandstacacs-server timeout

tagtag <WORD>

Description: Add a tag to an epg

Syntax:

Tag for the object (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# tag <WORD>

tag <WORD>

Description: Add a tag to an application

Syntax:



Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# tag <WORD>

tag <WORD>

Description: Add a tag to the tenant

Syntax:



Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>


T Commandstag

(config-tenant)# tag <WORD>

tag <NUMBER>

Description: Set Route Tag

Syntax:

Route Tag Value. Number range from=0 to=4294967295<0-4294967295>

Command Mode: template route tag : Configure Route Tag Policy Templates

Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template route tag <WORD> tenant <WORD>(config-route-tag)# tag <NUMBER>


T Commandstag

targettarget self|children|subtree

Description: Configure target dn/class

Syntax:

Selfself

Childrenchildren

Subtreesubtree


Command Path:

# configure [['terminal', 't']](config)# callhome common(config-callhome)# query-profile(config-callhome-queryprof)# query <WORD> type dn|class <dn/classname>(config-callhome-queryprof-query)# target self|children|subtree

target <WORD>

Description: Snapshot target

Syntax:

infra, fabric or tenant-xWORD


Command Path:

# configure [['terminal', 't']](config)# snapshot export <WORD>(config-export)# target <WORD>


T Commandstarget

telnettelnet

Description: TELNET communication policy group


Command Path:

# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# telnet


T Commandstelnet

template bfdtemplate bfd ip|ipv6 <WORD>

Description: BFD group of commands

Syntax:

IPV4 Addressip

IPV6 Addressipv6

Create a BFD policyWORD


Command Path:

# configure [['terminal', 't']](config)# template bfd ip|ipv6 <WORD>

template bfd <WORD> tenant <WORD>

Description: Configure BFD Interface Policy Templates

Syntax:

BFD Interface Policy name (Max Size 64)WORD

Tenant for the BFD Policytenant



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template bfd <WORD> tenant <WORD>


T Commandstemplate bfd

template bgp address-familytemplate bgp address-family <WORD> tenant <WORD>

Description: Configure Router BGP Address Family Templates

Syntax:

BGP Address Family Policy Name (Max Size 64)WORD

Tenant for the BGP Policytenant

Tenant NameWORD


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template bgp address-family <WORD> tenant <WORD>


T Commandstemplate bgp address-family

template bgp timerstemplate bgp timers <WORD> tenant <WORD>

Description: Configure Router BGP Timer Policy Templates

Syntax:

Router BGP Timer Policy Name (Max Size 64)WORD


Tenant Name (Max Size 63)WORD


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template bgp timers <WORD> tenant <WORD>


T Commandstemplate bgp timers

template community-list expandedtemplate community-list expanded <WORD> <regular expression> tenant <WORD>

Description: Configure expanded community list templates

Syntax:

community name (Max Size 64)WORD

community regular expression<regular expression>

Tenant for the VRFtenant

Tenant nameWORD


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template community-list expanded <WORD> <regular expression> tenant <WORD>


T Commandstemplate community-list expanded

template community-list standardtemplate community-list standard <WORD> <community list> tenant <WORD>

Description: Configure standard community list templates

Syntax:


<community list><community list>


Tenant nameWORD


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template community-list standard <WORD> <community list> tenant <WORD>


T Commandstemplate community-list standard

template dhcp optiontemplate dhcp option policy <WORD>

Description: Create a DHCP Option policy

Syntax:

Name of the DHCP Option Policypolicy

Name of the DHCP Option Policy (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template dhcp option policy <WORD>


T Commandstemplate dhcp option

template dhcp relaytemplate dhcp relay policy <WORD>

Description: Create a DHCP Relay policy

Syntax:

Name of the DHCP relay policypolicy



Command Path:

# configure [['terminal', 't']](config)# template dhcp relay policy <WORD>

template dhcp relay policy <WORD>

Description: Create a DHCP Relay policy

Syntax:

Name of the DHCP relay policypolicy



Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template dhcp relay policy <WORD>


T Commandstemplate dhcp relay

template eigrp interface-policytemplate eigrp interface-policy <WORD> tenant <WORD>

Description: Configure EIGRP Interface policy templates

Syntax:

Policy name (Max Size 64)WORD

Tenant for the EIGRP Interface Policytenant

Tenant nameWORD


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template eigrp interface-policy <WORD> tenant <WORD>


T Commandstemplate eigrp interface-policy

template eigrp vrf-policytemplate eigrp vrf-policy <WORD> tenant <WORD>

Description: Configure EIGRP VRF policy templates

Syntax:


Tenant for the EIGRP VRF Policytenant

Tenant nameWORD


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template eigrp vrf-policy <WORD> tenant <WORD>


T Commandstemplate eigrp vrf-policy

template endpoint retention policytemplate endpoint retention policy <WORD>

Description: Configure an endpoint retention policy

Syntax:

Name of the endpoint retention policy to set (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template endpoint retention policy <WORD>


T Commandstemplate endpoint retention policy

template extcommunity-list expandedtemplate extcommunity-list expanded <WORD> <regular expression> tenant <WORD>

Description: Configure expanded community list templates

Syntax:


community regular expression<regular expression>


Tenant nameWORD


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template extcommunity-list expanded <WORD> <regular expression> tenant <WORD>


T Commandstemplate extcommunity-list expanded

template extcommunity-list standardtemplate extcommunity-list standard <WORD> [scope <scope>] <community list> tenant <WORD>

Description: Configure standard community list templates

Syntax:


(Optional) transitive or non-transitivescope

<community list><community list>


Tenant nameWORD


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template extcommunity-list standard <WORD> [scope <scope>] <community list>tenant <WORD>


T Commandstemplate extcommunity-list standard

template ip igmp snooping policytemplate ip igmp snooping policy <WORD>

Description: Create an IGMP snooping policy

Syntax:

Name of the IGMP snooping policy to define (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip igmp snooping policy <WORD>


T Commandstemplate ip igmp snooping policy

template ipv6 nd policytemplate ipv6 nd policy <WORD>

Description: Create/modify an an IPv6 Neighbor Discovery policy

Syntax:

Name of the policy to create/modify (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ipv6 nd policy <WORD>

template ipv6 nd policy <WORD> tenant <WORD>

Description: Configure IPv6 Neighbor Discovery policy templates

Syntax:


Tenant for the ND Policytenant

Tenant nameWORD


Command Path:



T Commandstemplate ipv6 nd policy

template ipv6 nd prefixtemplate ipv6 nd prefix policy <WORD>

Description: Create/modify an an IPv6 Neighbor Prefix policy

Syntax:

IPv6 ND Prefix Policypolicy

Name of the policy to create/modify (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ipv6 nd prefix policy <WORD>


T Commandstemplate ipv6 nd prefix

template leaf-policy-grouptemplate leaf-policy-group <WORD>

Description: Configure Leaf Policy Group

Syntax:

Leaf Policy Group NameWORD


Command Path:

# configure [['terminal', 't']](config)# template leaf-policy-group <WORD>


T Commandstemplate leaf-policy-group

template ospf interface-policytemplate ospf interface-policy <WORD> tenant <WORD>

Description: Configure OSPF Interface Policy Templates

Syntax:

OSPF Interface Policy name (Max Size 64)WORD

Tenant for the OSPF Policytenant



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf interface-policy <WORD> tenant <WORD>


T Commandstemplate ospf interface-policy

template ospf vrf-policytemplate ospf vrf-policy <WORD> tenant <WORD>

Description: Configure Router OSPF Timer Policy Templates

Syntax:

Router OSPF Timer Policy name (Max Size 64)WORD




Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf vrf-policy <WORD> tenant <WORD>


T Commandstemplate ospf vrf-policy

template policy-grouptemplate policy-group <WORD>

Description: Configure Policy Group Parameters

Syntax:



Command Path:

# configure [['terminal', 't']](config)# template policy-group <WORD>


T Commandstemplate policy-group

template port-channeltemplate port-channel <WORD>

Description: Configure Port-Channel Parameters

Syntax:



Command Path:

# configure [['terminal', 't']](config)# template port-channel <WORD>


T Commandstemplate port-channel

template route-profiletemplate route-profile <WORD> tenant <WORD>

Description: Configure route-profile template under tenant for BGP dampening and route redistribution

Syntax:

Route-profile template name (Max Size 64)WORD

Tenant for the route-profile templatetenant



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template route-profile <WORD> tenant <WORD>

template route-profile <WORD>

Description: Configure route-profile template under VRF/L3Out for bridge-domain export

Syntax:

Route-profile template nameWORD


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# template route-profile <WORD>


T Commandstemplate route-profile

template route tagtemplate route tag <WORD> tenant <WORD>

Description: Configure Route Tag Policy Templates

Syntax:

Route Tag Policy Name (Max Size 64)WORD

Tenant for the Route Tag Policytenant



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template route tag <WORD> tenant <WORD>


T Commandstemplate route tag

tenanttenant <WORD>

Description: tenant configuration mode

Syntax:



Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>


T Commandstenant

terminalterminal length <NUMBER>

Description: Enable or disable pager for command output

Syntax:

Terminal length keywordlength

Terminal pager length (0=Disable pager). Number range from=0 to=511NUMBER


Command Path:

# terminal length <NUMBER>


T Commandsterminal

timetime start <date-time>

Description: Start controller-group upgrade

Syntax:

Set time to trigger upgradestart

Set the start time ([[[yyyy:]mmm:]dd:]HH:MM)<date-time>

Command Mode: controller-group : Controller Upgrade Configuration Mode

Command Path:

# configure [['terminal', 't']](config)# firmware(config-firmware)# controller-group(config-firmware-controller)# time start <date-time>

time start <TIME>

Description: Set the window start time

Syntax:

Set the start timestart

Set the start time [[[yyyy:]mmm:]dd:]HH:MMTIME


Command Path:

# configure [['terminal', 't']](config)# scheduler fabric|controller schedule <WORD>(config-scheduler)# absolute window <WORD>(config-scheduler-absolute)# time start <TIME>


T Commandstime

time start dailytime start daily <TIME>

Description: Specify a daily schedule

Syntax:

Trigger time in HH:MM formatTIME


Command Path:

# configure [['terminal', 't']](config)# scheduler fabric|controller schedule <WORD>(config-scheduler)# recurring window <WORD>(config-scheduler-recurring)# time start daily <TIME>


T Commandstime start daily

time start weeklytime start weekly monday|tuesday|wednesday|thursday|friday|saturday|sunday|even-day|odd-day|every-day<TIME>

Description: Specify a weekly schedule

Syntax:

Mondaysmonday

Tuesdaystuesday

Wednesdayswednesday

Thursdaysthursday

Fridaysfriday

Saturdayssaturday

Sundayssunday

Even dayseven-day

Odd daysodd-day

Everydayevery-day

Trigger time in HH:MM formatTIME


Command Path:

# configure [['terminal', 't']](config)# scheduler fabric|controller schedule <WORD>(config-scheduler)# recurring window <WORD>(config-scheduler-recurring)# time start weeklymonday|tuesday|wednesday|thursday|friday|saturday|sunday|even-day|odd-day|every-day <TIME>


T Commandstime start weekly

timeouttimeout <NUMBER>

Description: LDAP server timeout for authentication

Syntax:

LDAP server timeout for authentication. Number range from=5 to=60<5-60>


Command Path:

# configure [['terminal', 't']](config)# ldap-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# timeout <NUMBER>

timeout <0-60>

Description: RADIUS server timeout for authentication

Syntax:

RADIUS server timeout for authentication<0-60>


Command Path:

# configure [['terminal', 't']](config)# radius-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# timeout <0-60>

timeout <NUMBER>

Description: TACACS server timeout for authentication

Syntax:

TACACS server timeout for authentication. Number range from=0to=60

<0-60>


Command Path:

# configure [['terminal', 't']](config)# tacacs-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# timeout <NUMBER>


T Commandstimeout

timerstimers bgp <NUMBER> <NUMBER>

Description: Set BGP Policy Timers

Syntax:

Set BGP Policy Timersbgp

Keep-Alive Timer Value in Seconds. Number range from=0 to=3600<0-3600>

Hold Timer Value in Seconds. Number range from=0 to=3600<0-3600>


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template bgp timers <WORD> tenant <WORD>(config-bgp-timers)# timers bgp <NUMBER> <NUMBER>

timers active-time <NUMBER>

Description: Set EIGRP Timers

Syntax:

Active timer intervalactive-time

Active timer interval value in minutes. Number range from=1 to=65535<1-65535>


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template eigrp vrf-policy <WORD> tenant <WORD>(config-template-eigrp-vrf-pol)# timers active-time <NUMBER>

timers active-time <NUMBER>

Description: Set EIGRP Timers

Syntax:

Active timer intervalactive-time

Active timer interval value in minutes. Number range from=1 to=65535<1-65535>


T Commandstimers


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router eigrp default(config-eigrp)# vrf member tenant <WORD> vrf <WORD>(config-eigrp-vrf)# address-family ipv4|ipv6 unicast(config-address-family)# timers active-time <NUMBER>


T Commandstimers

timers lsa-arrivaltimers lsa-arrival <NUMBER>

Description: Set the minimum interval between the arrival of each link-state advertisement(LSA)

Syntax:

Interval in milliseconds. Number range from=10 to=600000<10-600000>


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf vrf-policy <WORD> tenant <WORD>(config-vrf-policy)# timers lsa-arrival <NUMBER>


T Commandstimers lsa-arrival

timers lsa-group-pacingtimers lsa-group-pacing <NUMBER>

Description: Set the interval in which LSAs are grouped and refreshed, checksummed, or aged

Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf vrf-policy <WORD> tenant <WORD>(config-vrf-policy)# timers lsa-group-pacing <NUMBER>


T Commandstimers lsa-group-pacing

timers throttle lsatimers throttle lsa <NUMBER> <NUMBER> <NUMBER>

Description: Set the start-interval, hold-interval, max-interval for LSA

Syntax:

The generation throttle start-wait interval between LSAs.. Number rangefrom=0 to=5000

<start-time 0-5000>

The incremental time (in milliseconds) used to calculate the subsequentrate limiting times for LSA generation.. Number range from=50to=30000

<hold-interval 50-30000>

The generation throttle maximum interval between LSAs.. Numberrange from=50 to=30000

<max-time 50-30000>


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf vrf-policy <WORD> tenant <WORD>(config-vrf-policy)# timers throttle lsa <NUMBER> <NUMBER> <NUMBER>


T Commandstimers throttle lsa

timers throttle spftimers throttle spf <NUMBER> <NUMBER> <NUMBER>

Description: Set the SPF init-interval, hold-interval, max-interval for LSA

Syntax:

The initial delay interval for the SPF schedule.. Number range from=1to=600000

<spf-start 1-600000>

The minimum hold time between SPF calculations.. Number rangefrom=1 to=600000

<spf-hold 1-600000>

The maximum interval between SPF calculations. Each interval afterthe initial calculation is twice as long as the previous one until the waitinterval reaches the maximum wait time specified.. Number rangefrom=1 to=600000

<spf-max-wait 1-600000>


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf vrf-policy <WORD> tenant <WORD>(config-vrf-policy)# timers throttle spf <NUMBER> <NUMBER> <NUMBER>


T Commandstimers throttle spf

tptp <WORD>

Description: Set third-party certificate from trusted source/point for device identity

Syntax:

third-party certificate (Max Size 16)<WORD>


Command Path:

# configure [['terminal', 't']](config)# crypto keyring <WORD>(config-keyring)# tp <WORD>


T Commandstp

transmit-delaytransmit-delay <NUMBER>


Syntax:



Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf interface-policy <WORD> tenant <WORD>(config-interface-policy)# transmit-delay <NUMBER>


T Commandstransmit-delay

transport email fromtransport email from <WORD>


Syntax:

The e-mail address (Max Size None)WORD


Command Path:

# configure [['terminal', 't']](config)# callhome common(config-callhome)# destination-profile(config-callhome-destnprof)# transport email from <WORD>


T Commandstransport email from

transport email mail-servertransport email mail-server <host/ipaddr> [port <port>] [mgmtepg <mgmtepg>]

Description: configure SMTP server

Syntax:

The hostname or ipaddress of the destination<host/ipaddr>

(Optional) Port Number. Number range from=1 to=633535port

(Optional) mgmtepgmgmtepg


Command Path:

# configure [['terminal', 't']](config)# callhome common(config-callhome)# destination-profile(config-callhome-destnprof)# transport email mail-server <host/ipaddr> [port <port>] [mgmtepg<mgmtepg>]


T Commandstransport email mail-server

transport email reply-totransport email reply-to <WORD>


Syntax:

Reply-To e-mail address (Max Size None)WORD


Command Path:

# configure [['terminal', 't']](config)# callhome common(config-callhome)# destination-profile(config-callhome-destnprof)# transport email reply-to <WORD>


T Commandstransport email reply-to

trigger fabric-recoverytrigger fabric-recovery <NUMBER> <WORD>

Description: Trigger fabric recovery

Syntax:

Size of the cluster. Number range from=1 to=16<cluster-size>

Snapshot import configuration nameWORD


Command Path:

# trigger fabric-recovery <NUMBER> <WORD>


T Commandstrigger fabric-recovery

trigger shutdowntrigger shutdown controller <NUMBER>

Description: Shutdown controller

Syntax:

Shutdown controllercontroller



Command Path:

# trigger shutdown controller <NUMBER>


T Commandstrigger shutdown

trigger snapshot downloadtrigger snapshot download <WORD>

Description: Trigger command for snapshot download

Syntax:

Snapshot download configuration nameWORD


Command Path:

# trigger snapshot download <WORD>


T Commandstrigger snapshot download

trigger snapshot exporttrigger snapshot export <WORD>

Description: Trigger command for snapshot export

Syntax:

Snapshot export configuration nameWORD


Command Path:

# trigger snapshot export <WORD>


T Commandstrigger snapshot export

trigger snapshot importtrigger snapshot import <WORD>

Description: Trigger command for snapshot import

Syntax:

Snapshot import configuration nameWORD


Command Path:

# trigger snapshot import <WORD>


T Commandstrigger snapshot import

trigger snapshot rollbacktrigger snapshot rollback <WORD>

Description: Trigger command for snapshot rollback

Syntax:

Snapshot rollback configuration nameWORD


Command Path:

# trigger snapshot rollback <WORD>


T Commandstrigger snapshot rollback

trigger snapshot uploadtrigger snapshot upload <WORD>

Description: Trigger command for snapshot upload

Syntax:

Snapshot upload configuration nameWORD


Command Path:

# trigger snapshot upload <WORD>


T Commandstrigger snapshot upload

trigger techsupport alltrigger techsupport all [remotename <remote-path>]

Description: Trigger techsupport for controllers and switches

Syntax:

(Optional) remote-pathremote-path


Command Path:

# trigger techsupport all [remotename <remote-path>]


T Commandstrigger techsupport all

trigger techsupport controllerstrigger techsupport controllers [remotename <remote-path>]

Description: Trigger techsupport for a controllers

Syntax:



Command Path:

# trigger techsupport controllers [remotename <remote-path>]


T Commandstrigger techsupport controllers

trigger techsupport hosttrigger techsupport host <NUMBER> remotename <remote-file-name> [node <leaf-node-id>]

Description: Trigger techsupport for a host

Syntax:

Specify the host Odev ID. Number range from=0to=9223372036854775807

<Odevid>

Specify the file remote path nameremotename

Remote path file name<remote-file-name>

(Optional) Specify the leaf node id<leaf-node-id>


Command Path:

# trigger techsupport host <NUMBER> remotename <remote-file-name> [node <leaf-node-id>]


T Commandstrigger techsupport host

trigger techsupport localtrigger techsupport local

Description: Trigger techsupport for a local


Command Path:

# trigger techsupport local


T Commandstrigger techsupport local

trigger techsupport switchtrigger techsupport switch switchId <switchId> [remotename <remote-path>]

Description: Trigger techsupport for a switch

Syntax:

switch id 101-4000 or range(s): 101-103,104switchId <switchId>



Command Path:

# trigger techsupport switch switchId <switchId> [remotename <remote-path>]


T Commandstrigger techsupport switch

trigger troubleshoot epext session reporttrigger troubleshoot epext session <session_name> report [format <format>]

Description: Trigger a report generation for a troubleshoot session

Syntax:

sessionsession


(Optional) Report formatformat


Command Path:

# trigger troubleshoot epext session <session_name> report [format <format>]


T Commandstrigger troubleshoot epext session report

trigger troubleshoot eptoep session reporttrigger troubleshoot eptoep session <session_name> report [format <format>]

Description: Trigger a report generation for a troubleshoot session

Syntax:

sessionsession




Command Path:

# trigger troubleshoot eptoep session <session_name> report [format <format>]


T Commandstrigger troubleshoot eptoep session report

trigger vmwaretrigger vmware domain <name> vcenter <hostname|IP> pull-inventory

Description: Trigger VMware vCenter inventory pull

Syntax:

VMware domaindomain

VMM VMware Domain name<name>

VMware vCentervcenter

vCenter hostname or IP<hostname|IP>

Pull inventorypull-inventory


Command Path:

# trigger vmware domain <name> vcenter <hostname|IP> pull-inventory


T Commandstrigger vmware

troubleshoot epext session atomiccountertroubleshoot epext session <session_name> atomiccounter

Description: Start atomic counter of a troubleshoot session

Syntax:

sessionsession



Command Path:

# configure [['terminal', 't']](config)# troubleshoot epext session <session_name> atomiccounter

Usage Note:

The usage of the troubleshoot epext session commands and the troubleshoot eptoep session commandsdiffers in the following way:

• Use the troubleshoot epext session command when one endpoint is local to the fabric and the otherendpoint is external to the fabric.

• Use the troubleshoot eptoep session command when both endpoints are local to the fabric.


T Commandstroubleshoot epext session atomiccounter

troubleshoot epext session descriptiontroubleshoot epext session <session_name> description <LINE>

Description: Set the description of a troubleshoot session

Syntax:

sessionsession



LINE


Command Path:

# configure [['terminal', 't']](config)# troubleshoot epext session <session_name> description <LINE>


T Commandstroubleshoot epext session description

troubleshoot epext session latestminutestroubleshoot epext session <session_name> latestminutes <minutes>

Description: Set the time window in number of minutes from current time

Syntax:

sessionsession


number of minutes from current time. Number range from=5 to=1440minutes


Command Path:

# configure [['terminal', 't']](config)# troubleshoot epext session <session_name> latestminutes <minutes>

Usage Note:





T Commandstroubleshoot epext session latestminutes

troubleshoot epext session monitor destination apictroubleshoot epext session <session_name> monitor destination apic srcipprefix <sip/m> [analyser <aip>][erspan-id <id>] [spansrcports <pathep-list>]

Description: Configure this APIC as monitor destination

Syntax:

sessionsession


destinatondestination

srcipprefixsrcipprefix

Source IP adddress and subnet mask lengthsip/m

(Optional) IP address of the host analyseraip

(Optional) erspan Id. Number range from=1 to=1023id

(Optional) List of source fabricPathEp dnpathep-list


Command Path:

# configure [['terminal', 't']](config)# troubleshoot epext session <session_name> monitor destination apic srcipprefix<sip/m> [analyser <aip>] [erspan-id <id>] [spansrcports <pathep-list>]

Usage Note:





T Commandstroubleshoot epext session monitor destination apic

troubleshoot epext session monitor destination prefdestgrouptroubleshoot epext session <session_name> monitor destination prefdestgroup <destgroup_name>[spansrcports <pathep-list>]

Description: Configure a predefined monitor destination

Syntax:

sessionsession



Destination group namedestgroup_name



Command Path:

# configure [['terminal', 't']](config)# troubleshoot epext session <session_name> monitor destination prefdestgroup<destgroup_name> [spansrcports <pathep-list>]

Usage Note:





T Commandstroubleshoot epext session monitor destination prefdestgroup

troubleshoot epext session monitor destination tenanttroubleshoot epext session <session_name> monitor destination tenant <tn_name> application <ap_name>epg <epg_name> destip <dip> srcipprefix <sip/m> [erspan-id <id>] [spansrcports <pathep-list>]

Description: Configure tenant EPG as monitor destination

Syntax:

sessionsession



tenant nametn_name


application nameap_name

epgepg

epg nameepg_name

destipdestip

destination IP addressdip


source IP address and subnet mask lengthsip/m




Command Path:

# configure [['terminal', 't']](config)# troubleshoot epext session <session_name> monitor destination tenant <tn_name>application <ap_name> epg <epg_name> destip <dip> srcipprefix <sip/m> [erspan-id <id>][spansrcports <pathep-list>]

Usage Note:



T Commandstroubleshoot epext session monitor destination tenant




T Commandstroubleshoot epext session monitor destination tenant

troubleshoot epext session schedulertroubleshoot epext session <session_name> scheduler <sch_name> [format <format>]

Description: Associate a scheduler to the troubleshoot session

Syntax:

sessionsession


scheduler namesch_name

(Optional) Reoport formatformat


Command Path:

# configure [['terminal', 't']](config)# troubleshoot epext session <session_name> scheduler <sch_name> [format <format>]

Usage Note:





T Commandstroubleshoot epext session scheduler

troubleshoot epext session srcextip destip tenant applicationtroubleshoot epext session <session_name> srcextip <sip> destip <dip> tenant <dtenant_name> application<dapp_name> epg <depg_name>

Description: application

Syntax:

sessionsession


external source IPsip

destipdestip

destination IPdip

tenanttenant

destination Tenantdtenant_name

destination Applicationdapp_name

epgepg

destination EPGdepg_name


Command Path:

# configure [['terminal', 't']](config)# troubleshoot epext session <session_name> srcextip <sip> destip <dip> tenant<dtenant_name> application <dapp_name> epg <depg_name>


T Commandstroubleshoot epext session srcextip destip tenant application

troubleshoot epext session srcextip destip tenant vrftroubleshoot epext session <session_name> srcextip <sip> destip <dip> tenant <dtenant_name> vrf<dvrf_name>

Description: vrf

Syntax:

sessionsession


external source IPsip

destipdestip

destination IPdip

tenanttenant


destination VRFdvrf_name


Command Path:

# configure [['terminal', 't']](config)# troubleshoot epext session <session_name> srcextip <sip> destip <dip> tenant<dtenant_name> vrf <dvrf_name>


T Commandstroubleshoot epext session srcextip destip tenant vrf

troubleshoot epext session srcip tenant application epgdestextip

troubleshoot epext session <session_name> srcip <sip> tenant <stenant_name> application <sapp_name>epg <sepg_name> destextip <dip>

Description: External IP

Syntax:

sessionsession


source IPsip

tenanttenant

source Tenantstenant_name

source Applicationsapp_name

epgepg

source EPGsepg_name

external destination IPdip


Command Path:

# configure [['terminal', 't']](config)# troubleshoot epext session <session_name> srcip <sip> tenant <stenant_name>application <sapp_name> epg <sepg_name> destextip <dip>


T Commandstroubleshoot epext session srcip tenant application epg destextip

troubleshoot epext session srcip tenant vrf destextiptroubleshoot epext session <session_name> srcip <sip> tenant <stenant_name> vrf <svrf_name> destextip<dip>

Description: external IP

Syntax:

sessionsession


source IPsip

tenanttenant


source VRFsvrf_name

external destination IPdip


Command Path:

# configure [['terminal', 't']](config)# troubleshoot epext session <session_name> srcip <sip> tenant <stenant_name> vrf<svrf_name> destextip <dip>


T Commandstroubleshoot epext session srcip tenant vrf destextip

troubleshoot epext session starttimetroubleshoot epext session <session_name> starttime <start_time> endtime <end_time>

Description: Configure the start/end time of the session

Syntax:

sessionsession


Start time (in YYYY-MM-DDTHH:MM:SS format)start_time

end timeendtime

End time (in YYYY-MM-DDTHH:MM:SS format)end_time


Command Path:

# configure [['terminal', 't']](config)# troubleshoot epext session <session_name> starttime <start_time> endtime <end_time>

Usage Note:





T Commandstroubleshoot epext session starttime

troubleshoot epext session traceroutetroubleshoot epext session <session_name> traceroute

Description: Start traceroute of a troubleshoot session

Syntax:

sessionsession



Command Path:

# configure [['terminal', 't']](config)# troubleshoot epext session <session_name> traceroute

Usage Note:





T Commandstroubleshoot epext session traceroute

troubleshoot epext session traceroute protocol icmptroubleshoot epext session <session_name> traceroute protocol icmp

Description: ICMP protocol

Syntax:

sessionsession



Command Path:

# configure [['terminal', 't']](config)# troubleshoot epext session <session_name> traceroute protocol icmp

Usage Note:





T Commandstroubleshoot epext session traceroute protocol icmp

troubleshoot epext session traceroute protocol tcptroubleshoot epext session <session_name> traceroute protocol tcp [destport <port>]

Description: TCP protocol

Syntax:

sessionsession


(Optional) TCP destination port number. Number range from=0to=65535

port


Command Path:

# configure [['terminal', 't']](config)# troubleshoot epext session <session_name> traceroute protocol tcp [destport <port>]

Usage Note:





T Commandstroubleshoot epext session traceroute protocol tcp

troubleshoot epext session traceroute protocol udptroubleshoot epext session <session_name> traceroute protocol udp [destport <port>]

Description: UDP protocol

Syntax:

sessionsession


(Optional) UDP destination port number. Number range from=0to=65535

port


Command Path:

# configure [['terminal', 't']](config)# troubleshoot epext session <session_name> traceroute protocol udp [destport <port>]

Usage Note:





T Commandstroubleshoot epext session traceroute protocol udp

troubleshoot eptoep session atomiccountertroubleshoot eptoep session <session_name> atomiccounter

Description: Start atomic counter of a troubleshoot session

Syntax:

sessionsession



Command Path:

# configure [['terminal', 't']](config)# troubleshoot eptoep session <session_name> atomiccounter

Usage Note:





T Commandstroubleshoot eptoep session atomiccounter

troubleshoot eptoep session descriptiontroubleshoot eptoep session <session_name> description <LINE>

Description: Set the description of a troubleshoot session

Syntax:

sessionsession



LINE


Command Path:

# configure [['terminal', 't']](config)# troubleshoot eptoep session <session_name> description <LINE>

Usage Note:





T Commandstroubleshoot eptoep session description

troubleshoot eptoep session latestminutestroubleshoot eptoep session <session_name> latestminutes <minutes>

Description: Set the time window in number of minutes from current time

Syntax:

sessionsession


number of minutes from current time. Number range from=5 to=1440minutes


Command Path:

# configure [['terminal', 't']](config)# troubleshoot eptoep session <session_name> latestminutes <minutes>

Usage Note:





T Commandstroubleshoot eptoep session latestminutes

troubleshoot eptoep session monitor destination apictroubleshoot eptoep session <session_name> monitor destination apic srcipprefix <sip/m> [analyser <aip>][erspan-id <id>] [spansrcports <pathep-list>]

Description: Configure this APIC as monitor destination

Syntax:

sessionsession




Source IP adddress and subnet mask lengthsip/m

(Optional) IP address of the host analyseraip




Command Path:

# configure [['terminal', 't']](config)# troubleshoot eptoep session <session_name> monitor destination apic srcipprefix<sip/m> [analyser <aip>] [erspan-id <id>] [spansrcports <pathep-list>]

Usage Note:





T Commandstroubleshoot eptoep session monitor destination apic

troubleshoot eptoep session monitor destination prefdestgrouptroubleshoot eptoep session <session_name> monitor destination prefdestgroup <destgroup_name>[spansrcports <pathep-list>]

Description: Configure a predefined monitor destination

Syntax:

sessionsession



Destination group namedestgroup_name



Command Path:

# configure [['terminal', 't']](config)# troubleshoot eptoep session <session_name> monitor destination prefdestgroup<destgroup_name> [spansrcports <pathep-list>]

Usage Note:





T Commandstroubleshoot eptoep session monitor destination prefdestgroup

troubleshoot eptoep session monitor destination tenanttroubleshoot eptoep session <session_name> monitor destination tenant <tn_name> application <ap_name>epg <epg_name> destip <dip> srcipprefix <sip/m> [erspan-id <id>] [spansrcports <pathep-list>]

Description: Configure tenant EPG as monitor destination

Syntax:

sessionsession



tenant nametn_name


application nameap_name

epgepg

epg nameepg_name

destipdestip

destination IP addressdip


source IP address and subnet mask lenghtsip/m




Command Path:

# configure [['terminal', 't']](config)# troubleshoot eptoep session <session_name> monitor destination tenant <tn_name>application <ap_name> epg <epg_name> destip <dip> srcipprefix <sip/m> [erspan-id <id>][spansrcports <pathep-list>]

Usage Note:



T Commandstroubleshoot eptoep session monitor destination tenant




T Commandstroubleshoot eptoep session monitor destination tenant

troubleshoot eptoep session schedulertroubleshoot eptoep session <session_name> scheduler <sch_name> [format <format>]

Description: Associate a scheduler to the troubleshoot session

Syntax:

sessionsession


scheduler namesch_name



Command Path:

# configure [['terminal', 't']](config)# troubleshoot eptoep session <session_name> scheduler <sch_name> [format <format>]

Usage Note:





T Commandstroubleshoot eptoep session scheduler

troubleshoot eptoep session srcip tenant application epg destiptenant application

troubleshoot eptoep session <session_name> srcip <sip> tenant <stenant_name> application <sapp_name>epg <sepg_name> destip <dip> tenant <dtenant_name> application <dapp_name> epg <depg_name>


Syntax:

sessionsession


source IPsip

tenanttenant



epgepg

source EPGsepg_name

destipdestip

destination IPdip

tenanttenant



epgepg



Command Path:

# configure [['terminal', 't']](config)# troubleshoot eptoep session <session_name> srcip <sip> tenant <stenant_name>application <sapp_name> epg <sepg_name> destip <dip> tenant <dtenant_name> application<dapp_name> epg <depg_name>


T Commandstroubleshoot eptoep session srcip tenant application epg destip tenant application

troubleshoot eptoep session srcip tenant application epg destiptenant vrf

troubleshoot eptoep session <session_name> srcip <sip> tenant <stenant_name> application <sapp_name>epg <sepg_name> destip <dip> tenant <dtenant_name> vrf <dvrf_name>

Description: vrf

Syntax:

sessionsession


source IPsip

tenanttenant



epgepg

source EPGsepg_name

destipdestip

destination IPdip

tenanttenant




Command Path:

# configure [['terminal', 't']](config)# troubleshoot eptoep session <session_name> srcip <sip> tenant <stenant_name>application <sapp_name> epg <sepg_name> destip <dip> tenant <dtenant_name> vrf <dvrf_name>


T Commandstroubleshoot eptoep session srcip tenant application epg destip tenant vrf

troubleshoot eptoep session srcip tenant vrf destip tenantapplication

troubleshoot eptoep session <session_name> srcip <sip> tenant <stenant_name> vrf <svrf_name> destip<dip> tenant <dtenant_name> application <dapp_name> epg <depg_name>


Syntax:

sessionsession


source IPsip

tenanttenant


source VRFsvrf_name

destipdestip

destination IPdip

tenanttenant



epgepg



Command Path:

# configure [['terminal', 't']](config)# troubleshoot eptoep session <session_name> srcip <sip> tenant <stenant_name> vrf<svrf_name> destip <dip> tenant <dtenant_name> application <dapp_name> epg <depg_name>


T Commandstroubleshoot eptoep session srcip tenant vrf destip tenant application

troubleshoot eptoep session srcip tenant vrf destip tenant vrftroubleshoot eptoep session <session_name> srcip <sip> tenant <stenant_name> vrf <svrf_name> destip<dip> tenant <dtenant_name> vrf <WORD>

Description: vrf

Syntax:

sessionsession


source IPsip

tenanttenant


source VRFsvrf_name

destipdestip

destination IPdip

tenanttenant


destination VRFWORD


Command Path:

# configure [['terminal', 't']](config)# troubleshoot eptoep session <session_name> srcip <sip> tenant <stenant_name> vrf<svrf_name> destip <dip> tenant <dtenant_name> vrf <WORD>


T Commandstroubleshoot eptoep session srcip tenant vrf destip tenant vrf

troubleshoot eptoep session srcmac tenant application epgdestmac tenant application

troubleshoot eptoep session <session_name> srcmac <smac> tenant <stenant_name> application<sapp_name> epg <sepg_name> destmac <dmac> tenant <dtenant_name> application <dapp_name> epg<depg_name>


Syntax:

sessionsession


source MACsmac

tenanttenant



epgepg

source EPGsepg_name

destmacdestmac

destination MACdmac

tenanttenant



epgepg



Command Path:

# configure [['terminal', 't']](config)# troubleshoot eptoep session <session_name> srcmac <smac> tenant <stenant_name>application <sapp_name> epg <sepg_name> destmac <dmac> tenant <dtenant_name> application


T Commandstroubleshoot eptoep session srcmac tenant application epg destmac tenant application

<dapp_name> epg <depg_name>


T Commandstroubleshoot eptoep session srcmac tenant application epg destmac tenant application

troubleshoot eptoep session srcmac tenant application epgdestmac tenant vrf

troubleshoot eptoep session <session_name> srcmac <smac> tenant <stenant_name> application<sapp_name> epg <sepg_name> destmac <dmac> tenant <dtenant_name> vrf <dvrf_name>

Description: vrf

Syntax:

sessionsession


source MACsmac

tenanttenant



epgepg

source EPGsepg_name

destmacdestmac

destination MACdmac

tenanttenant




Command Path:

# configure [['terminal', 't']](config)# troubleshoot eptoep session <session_name> srcmac <smac> tenant <stenant_name>application <sapp_name> epg <sepg_name> destmac <dmac> tenant <dtenant_name> vrf <dvrf_name>


T Commandstroubleshoot eptoep session srcmac tenant application epg destmac tenant vrf

troubleshoot eptoep session srcmac tenant vrf destmac tenantapplication

troubleshoot eptoep session <session_name> srcmac <smac> tenant <stenant_name> vrf <svrf_name>destmac <dmac> tenant <dtenant_name> application <dapp_name> epg <depg_name>


Syntax:

sessionsession


source MACsmac

tenanttenant


source VRFsvrf_name

destmacdestmac

destination MACdmac

tenanttenant



epgepg



Command Path:

# configure [['terminal', 't']](config)# troubleshoot eptoep session <session_name> srcmac <smac> tenant <stenant_name>vrf <svrf_name> destmac <dmac> tenant <dtenant_name> application <dapp_name> epg <depg_name>


T Commandstroubleshoot eptoep session srcmac tenant vrf destmac tenant application

troubleshoot eptoep session srcmac tenant vrf destmac tenantvrf

troubleshoot eptoep session <session_name> srcmac <smac> tenant <stenant_name> vrf <svrf_name>destmac <dmac> tenant <dtenant_name> vrf <dvrf_name>

Description: vrf

Syntax:

sessionsession


source MACsmac

tenanttenant


source VRFsvrf_name

destmacdestmac

destination MACdmac

tenanttenant




Command Path:

# configure [['terminal', 't']](config)# troubleshoot eptoep session <session_name> srcmac <smac> tenant <stenant_name>vrf <svrf_name> destmac <dmac> tenant <dtenant_name> vrf <dvrf_name>


T Commandstroubleshoot eptoep session srcmac tenant vrf destmac tenant vrf

troubleshoot eptoep session starttimetroubleshoot eptoep session <session_name> starttime <start_time> endtime <end_time>

Description: Configure the start/end time of the session

Syntax:

sessionsession


Start time (in YYYY-MM-DDTHH:MM:SS format)start_time

end timeendtime

End time (in YYYY-MM-DDTHH:MM:SS format)end_time


Command Path:

# configure [['terminal', 't']](config)# troubleshoot eptoep session <session_name> starttime <start_time> endtime <end_time>

Usage Note:





T Commandstroubleshoot eptoep session starttime

troubleshoot eptoep session traceroutetroubleshoot eptoep session <session_name> traceroute

Description: Start traceroute of a troubleshoot session

Syntax:

sessionsession



Command Path:

# configure [['terminal', 't']](config)# troubleshoot eptoep session <session_name> traceroute

Usage Note:





T Commandstroubleshoot eptoep session traceroute

troubleshoot eptoep session traceroute protocol icmptroubleshoot eptoep session <session_name> traceroute protocol icmp

Description: ICMP protocol

Syntax:

sessionsession



Command Path:

# configure [['terminal', 't']](config)# troubleshoot eptoep session <session_name> traceroute protocol icmp

Usage Note:





T Commandstroubleshoot eptoep session traceroute protocol icmp

troubleshoot eptoep session traceroute protocol tcptroubleshoot eptoep session <session_name> traceroute protocol tcp [destport <port>]

Description: TCP protocol

Syntax:

sessionsession


(Optional) TCP destination port number. Number range from=0to=65535

port


Command Path:

# configure [['terminal', 't']](config)# troubleshoot eptoep session <session_name> traceroute protocol tcp [destport<port>]

Usage Note:





T Commandstroubleshoot eptoep session traceroute protocol tcp

troubleshoot eptoep session traceroute protocol udptroubleshoot eptoep session <session_name> traceroute protocol udp [destport <port>]

Description: UDP protocol

Syntax:

sessionsession


(Optional) UDP destination port number. Number range from=0to=65535

port


Command Path:

# configure [['terminal', 't']](config)# troubleshoot eptoep session <session_name> traceroute protocol udp [destport<port>]

Usage Note:





T Commandstroubleshoot eptoep session traceroute protocol udp

trusted-keytrusted-key <id>

Description: Configure trusted for ntp authentication key

Syntax:

Id for the trusted key. Number range from=1 to=65535id


Command Path:

# configure [['terminal', 't']](config)# pod 1(config-pod)# ntp(config-ntp)# trusted-key <id>


T Commandstrusted-key


T Commandstrusted-key

U Commands

• ui-idle-timeout-seconds, page 1430

• unicast, page 1431

• update-source ethernet, page 1432

• update-source loopback, page 1433

• update-source vlan, page 1434

• use-keyring, page 1435

• use-vrf, page 1436

• user, page 1437

• username, page 1438


ui-idle-timeout-secondsui-idle-timeout-seconds <NUMBER>

Description: Set maximum GUI idle duration before requiring login refresh

Syntax:

Set maximumGUI idle duration before requiring login refresh. Numberrange from=60 to=65525

<60-65525>


Command Path:

# configure [['terminal', 't']](config)# crypto webtoken(config-webtoken)# ui-idle-timeout-seconds <NUMBER>


U Commandsui-idle-timeout-seconds

unicastunicast routing

Description: Instruct the fabric to route based on IP

Syntax:

Unicast routing settingrouting


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>(config-tenant-bd)# unicast routing


U Commandsunicast

update-source ethernetupdate-source ethernet <interfaceRange>

Description: Source Ethernet Interface

Syntax:

<interfaceRange><interfaceRange>


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [l3out <WORD>](config-leaf-bgp-vrf-neighbor)# update-source ethernet <interfaceRange>


U Commandsupdate-source ethernet

update-source loopbackupdate-source loopback <A.B.C.D>

Description: Source Loopback Interface

Syntax:

IPv4 or IPv6 Address without maskA.B.C.D


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [l3out <WORD>](config-leaf-bgp-vrf-neighbor)# update-source loopback <A.B.C.D>


U Commandsupdate-source loopback

update-source vlanupdate-source vlan <vlan>

Description: Source Vlan Interface

Syntax:

Vlan ID<vlan>


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [l3out <WORD>](config-leaf-bgp-vrf-neighbor)# update-source vlan <vlan>


U Commandsupdate-source vlan

use-keyringuse-keyring <keyring-name>

Description: Use specified keyring for the HTTPS Server SSL certificate

Syntax:

Keyring name (Max Size 64)keyring-name


Command Path:

# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# https(config-https)# use-keyring <keyring-name>


U Commandsuse-keyring

use-vrfuse-vrf <arg>

Description: Configure the management vrf for dns servers

Syntax:

Configure management vrfarg


Command Path:

# configure [['terminal', 't']](config)# dns(config-dns)# use-vrf <>


U Commandsuse-vrf

useruser <WORD>

Description: Set the remote path user name and password

Syntax:

User nameWORD


Command Path:

# configure [['terminal', 't']](config)# remote path <WORD>(config-remote)# user <WORD>


U Commandsuser

usernameusername <WORD>

Description: Create a locally-authenticated user account

Syntax:

User name (Max Size 28)WORD


Command Path:

# configure [['terminal', 't']](config)# username <WORD>

username <WORD>

Description: Configure a user account for the VCenter

Syntax:

Username for the accountWORD


Command Path:

# configure [['terminal', 't']](config)# vmware-domain <WORD>(config-vmware)# vcenter <> datacenter <WORD> [dvs-version <>](config-vmware-vc)# username <WORD>

username <WORD>

Description: Configure a user account for the vshield

Syntax:

Username for the accountWORD

Command Mode: vshield : Configure a VShield in the VMware domain

Command Path:

# configure [['terminal', 't']](config)# vmware-domain <WORD>(config-vmware)# vcenter <> datacenter <WORD> [dvs-version <>](config-vmware-vc)# vshield <>


U Commandsusername

(config-vmware-vc-vs)# username <WORD>


U Commandsusername


U Commandsusername

V Commands

• vcenter, page 1442

• vlan-domain, page 1443

• vlan-pool, page 1447

• vlan, page 1448

• vmware-domain, page 1450

• vnic, page 1451

• vpc context, page 1452

• vpc domain consecutive, page 1453

• vpc domain explicit, page 1454

• vpc domain reciprocal, page 1455

• vrf, page 1456

• vshield, page 1461

• vxlan, page 1462

• vxlan multicast-pool, page 1463

• vxlan pool, page 1464


vcentervcenter <arg> datacenter <WORD> [dvs-version <arg>]

Description: Configure a VCenter in the VMware domain

Syntax:

arg

Datacenter Namedatacenter

Datacenter NameWORD

(Optional)arg


Command Path:

# configure [['terminal', 't']](config)# vmware-domain <WORD>(config-vmware)# vcenter <> datacenter <WORD> [dvs-version <>]


V Commandsvcenter

vlan-domainvlan-domain <name> [dynamic] [type <domain-type>]

Description: Configure vlan domain

Syntax:

Vlan domain name (Max Size 64)name

(Optional) Create dynamic namespace(default is static)dynamic

(Optional) Vlan domain type<domain-type>


Command Path:

# configure [['terminal', 't']](config)# vlan-domain <name> [dynamic] [type <domain-type>]

vlan-domain member <WORD> [type <arg>]

Description: Attach VMware Domain to a VLAN Domain

Syntax:

Bind VMware domain to vlan domainmember

VLAN Domain nameWORD

(Optional) Vlan domain typearg


Command Path:

# configure [['terminal', 't']](config)# vmware-domain <WORD>(config-vmware)# vlan-domain member <WORD> [type <>]


Description: Attach Microsoft Domain to a VLAN Domain

Syntax:

Bind Microsoft domain to vlan domainmember

VLAN Domain nameWORD


V Commandsvlan-domain

(Optional) Vlan domain typearg

Command Mode: microsoft-domain : Create a VMMMicrosoft Domain

Command Path:

# configure [['terminal', 't']](config)# microsoft-domain <WORD>(config-microsoft)# vlan-domain member <WORD> [type <>]


Description: Configure Vlan Domain

Syntax:

Configure Vlan Domain Membermember

Vlan domain name (Max Size 64)WORD

(Optional)arg


Command Path:

# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# vlan-domain member <WORD> [type <>]



Syntax:



(Optional)arg


Command Path:

# configure [['terminal', 't']](config)# template port-channel <WORD>(config-if)# vlan-domain member <WORD> [type <>]





Syntax:



(Optional)arg


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# vlan-domain member <WORD> [type <>]



Syntax:



(Optional)arg


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# vlan-domain member <WORD> [type <>]



Syntax:



(Optional)arg




Command Path:

# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# vlan-domain member <WORD> [type <>]



vlan-poolvlan-pool <pool-name>

Description: Assign vlan-pool to vlan-domain

Syntax:

Vlan-pool name (Max Size 64)pool-name


Command Path:

# configure [['terminal', 't']](config)# vlan-domain <name> [dynamic] [type <domain-type>](config-vlan)# vlan-pool <pool-name>


V Commandsvlan-pool

vlanvlan <vlan-range> [dynamic]

Description: Add VLANs to vlan-domain

Syntax:

VLAN ID 1-4094 or range(s): 1-5, 10 or 2-5,7-19<vlan-range>

(Optional) Vlan allocation dynamically managed by APIC(default isstatic)

dynamic


Command Path:

# configure [['terminal', 't']](config)# vlan-domain <name> [dynamic] [type <domain-type>](config-vlan)# vlan <vlan-range> [dynamic]

vlan <1-4094>

Description: Configure Vlan for inband epg Controller inband ports

Syntax:



Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# inband-mgmt epg <WORD>(config-inb-epg)# vlan <1-4094>

vlan <1-4094>

Description: Configure Vlan for APIC Inband Port

Syntax:




V Commandsvlan

Command Path:

# configure [['terminal', 't']](config)# controller(config-controller)# interface inband-mgmt0(config-controller-if)# vlan <1-4094>


V Commandsvlan

vmware-domainvmware-domain <WORD>

Description: Create a VMM VMware Domain

Syntax:

VMM VMware Domain nameWORD


Command Path:

# configure [['terminal', 't']](config)# vmware-domain <WORD>

vmware-domain member <WORD> [encap <WORD>] [primary-encap <WORD>] [allow-micro-segmentation][deploy <WORD>] [push <WORD>]

Description: Associate EPG to a VMWare Domain

Syntax:

Bind the EPG to a VMware domainmember

VMware Domain NameWORD

(Optional) Enforce encap value. Secondary encapwhen EPG is isolated(For example vlan-10 or auto)

WORD

(Optional) Primary encap when EPG is isolated (For example vlan-11or auto)

WORD

(Optional) allow-micro-segmentationallow-micro-segmentation

(Optional) Deployment modeWORD

(Optional) Push modeWORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# vmware-domain member <WORD> [encap <WORD>] [primary-encap <WORD>][allow-micro-segmentation] [deploy <WORD>] [push <WORD>]


V Commandsvmware-domain

vnicvnic <vnic-name>

Description: Configure Virtual NIC as Cluster Member Interface

Syntax:

Name of VNIC of virtual cluster device.<vnic-name>


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 cluster name <WORD> type <type> vlan-domain <domain-name> [service<service>] [function <function>](config-cluster)# cluster-interface <WORD> [vlan <NUMBER>](config-cluster-interface)# member device <WORD> device-interface <WORD>(config-member)# vnic <vnic-name>


V Commandsvnic

vpc contextvpc context leaf <101-4000> <101-4000> [fex <fex>]

Description: Enter vpc context

Syntax:

Provide leaf detailsleaf

Id or Name of Leaf1<101-4000>

Id or Name of Leaf2<101-4000>



Command Path:

# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>]


V Commandsvpc context

vpc domain consecutivevpc domain consecutive

Description: Pair all discovered leaves consecutively e.g. 101-102, 103-104


Command Path:

# configure [['terminal', 't']](config)# vpc domain consecutive


V Commandsvpc domain consecutive

vpc domain explicitvpc domain explicit <NUMBER> leaf <101-4000> <101-4000>

Description: Pair two leaf nodes explicitly

Syntax:

Domain Id. Number range from=1 to=1000<1-1000>

Pair two leaf nodesleaf

First leaf member of the Pair<101-4000>

Second leaf member of the Pair<101-4000>


Command Path:

# configure [['terminal', 't']](config)# vpc domain explicit <NUMBER> leaf <101-4000> <101-4000>


V Commandsvpc domain explicit

vpc domain reciprocalvpc domain reciprocal

Description: Pair all discovered leaves reciprocally e.g. 101-103, 102-104


Command Path:

# configure [['terminal', 't']](config)# vpc domain reciprocal


V Commandsvpc domain reciprocal

vrfvrf context <WORD>

Description: Configuration for vrf

Syntax:

VRF namecontext

VRF name (Max Size 64)WORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>

vrf member <WORD>

Description: Configure VRF parameters

Syntax:

Set L3Out's VRF membershipmember

VRF nameWORD

Command Mode: l3out : Configuration for L3Out

Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l3out <WORD>(config-tenant-l3out)# vrf member <WORD>

vrf member <WORD>

Description: Associate the bridge-domain with a VRF

Syntax:

Associate the bridge-domain with a VRFmember

VRF name to associated (Max Size 64)WORD


V Commandsvrf


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>(config-tenant-bd)# vrf member <WORD>

vrf member <WORD>


Syntax:

Set interface's VRF membershipmember

VRF nameWORD


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l3 epg <WORD> [oob-mgmt] [l3out <l3out>](config-tenant-l3ext-epg)# vrf member <WORD>

vrf context tenant <WORD> vrf <WORD> [l3out <l3out>]


Syntax:

Enable VRF and enter VRF modecontext


Tenant nameWORD

Virtual Routing and Forwarding instancevrf

VRF nameWORD

(Optional) Configure VRF in API created l3outl3out


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>]


V Commandsvrf

vrf member tenant <WORD> vrf <WORD>


Syntax:


Tenanttenant

Tenant nameWORD


VRF nameWORD


Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# vrf member tenant <WORD> vrf <WORD>

vrf member tenant <WORD> vrf <WORD> [l3out] WORD


Syntax:


Tenanttenant

Tenant nameWORD


VRF nameWORD

(Optional) Enable VRF on one or more l3extOutl3out

l3extOut NameWORD


Command Path:



V Commandsvrf

(config-leaf-if)# vrf member tenant <WORD> vrf <WORD> [l3out] WORD


Description: Configure VRF information

Syntax:

Set VRF membershipmember

Tenanttenant

Tenant nameWORD

VRFvrf

VRF nameWORD

Command Mode: router eigrp : Enhanced Interior Gateway Routing Protocol (EIGRP)

Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router eigrp default(config-eigrp)# vrf member tenant <WORD> vrf <WORD>


Description: Associate Router OSPF Policy with Tenant/VRF

Syntax:

Set VRF membershipmember


Tenant nameWORD

VRFvrf

VRF nameWORD

Command Mode: router ospf : Open Shortest Path First (OSPF and OSPF Version3)

Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>


V Commandsvrf


Description: Virtual Router Context

Syntax:

Set BGP's VRF membershipmember




VRF Name (Max Size 64)WORD

Command Mode: router bgp : Border Gateway Protocol (BGP)

Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>


V Commandsvrf

vshieldvshield <arg>

Description: Configure a VShield in the VMware domain

Syntax:

arg


Command Path:

# configure [['terminal', 't']](config)# vmware-domain <WORD>(config-vmware)# vcenter <> datacenter <WORD> [dvs-version <>](config-vmware-vc)# vshield <>


V Commandsvshield

vxlanvxlan multicast-pool <ip-range>

Description: Configure VXLAN multicast pool.

Syntax:

multicast poolmulticast-pool

Multicast IP range<ip-range>


Command Path:

# configure [['terminal', 't']](config)# vmware-domain <WORD>(config-vmware)# configure-avs(config-vmware-avs)# vxlan multicast-pool <ip-range>


V Commandsvxlan

vxlan multicast-poolvxlan multicast-pool <ip-range>

Description: Configure VXLAN multicast pool.

Syntax:

Multicast IP range<ip-range>


Command Path:

# configure [['terminal', 't']](config)# vmware-domain <WORD>(config-vmware)# vcenter <> datacenter <WORD> [dvs-version <>](config-vmware-vc)# vshield <>(config-vmware-vc-vs)# vxlan multicast-pool <ip-range>


V Commandsvxlan multicast-pool

vxlan poolvxlan pool <vxlan-range>

Description: Configure VXLAN pool.

Syntax:

VXLAN range<vxlan-range>


Command Path:

# configure [['terminal', 't']](config)# vmware-domain <WORD>(config-vmware)# vcenter <> datacenter <WORD> [dvs-version <>](config-vmware-vc)# vshield <>(config-vmware-vc-vs)# vxlan pool <vxlan-range>


V Commandsvxlan pool

W Commands

• webtoken-timeout-seconds, page 1466

• weight, page 1467

• where, page 1468

• where detail, page 1469

• winservers, page 1470


webtoken-timeout-secondswebtoken-timeout-seconds <NUMBER>

Description: Set The web token timeout interval

Syntax:

Set The web token timeout interval. Number range from=300 to=9600<300-9600>


Command Path:

# configure [['terminal', 't']](config)# crypto webtoken(config-webtoken)# webtoken-timeout-seconds <NUMBER>


W Commandswebtoken-timeout-seconds

weightweight <NUMBER>

Description:Weight attribute that is local to a router.

Syntax:

Assigns a weight to all routes learned through the neighbor. Numberrange from=0 to=65535

<0-65535>

Command Mode: address-family : Configure an address-family for peer

Command Path:

# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [l3out <WORD>](config-leaf-bgp-vrf-neighbor)# address-family ipv4|ipv6 unicast(config-leaf-bgp-vrf-neighbor-af)# weight <NUMBER>


W Commandsweight

wherewhere

Description: show the current mode


Command Path:

# where


W Commandswhere

where detailwhere detail

Description: show detailed mode information


Command Path:

# where detail


W Commandswhere detail

winserverswinservers <windows server ip>

Description: Add windows server

Syntax:

windows server ipwindows server ip


Command Path:

# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# microsoft static-ip-pool <name> gateway <gwAddress>(config-tenant-app-epg-ms-ip-pool)# winservers <windows server ip>


W Commandswinservers

Z Commands

• zone, page 1472

• zones, page 1473


zonezone <WORD>

Description: Create zone policy

Syntax:

zone name (Max Size 64)WORD

Command Mode: zones : Zones configuration Mode

Command Path:

# configure [['terminal', 't']](config)# zones(config-zones)# zone <WORD>


Z Commandszone

zoneszones

Description: Zones configuration Mode


Command Path:

# configure [['terminal', 't']](config)# zones


Z Commandszones


Z Commandszones

Documents

Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) · Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) First Published: 2016-02-22 Last Modified: 2016-11-18