Upload
duongtram
View
215
Download
0
Embed Size (px)
Citation preview
Cisco ACI Switch Command Reference, NX-OS Release 13.xFirst Published: 2017-08-15
Last Modified: 2017-11-14
Americas HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706USAhttp://www.cisco.comTel: 408 526-4000 800 553-NETS (6387)Fax: 408 527-0883
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS,INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND,EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITEDWARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITHTHE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY,CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB's public domain versionof the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.
NOTWITHSTANDINGANYOTHERWARRANTYHEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS"WITH ALL FAULTS.CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OFMERCHANTABILITY, FITNESS FORA PARTICULAR PURPOSEANDNONINFRINGEMENTORARISING FROMACOURSEOFDEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUTLIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERSHAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, networktopology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentionaland coincidental.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: http://www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnershiprelationship between Cisco and any other company. (1110R)
Please send general FSF & GNU inquiries to [email protected]. There are also other ways to contact the FSF. Please send broken links and other corrections or suggestions [email protected]. Please see the Translations README for information on coordinating and submitting translations of this article.
Copyright © 2007, 2009, 2011 Free Software Foundation, Inc. Verbatim copying and distribution of this entire article are permitted worldwide, without royalty, in any medium, providedthis notice, and the copyright notice, are preserved. Updated: Date: 2011/06/28 02:44:32
© 2017 Cisco Systems, Inc. All rights reserved.
C O N T E N T S
P r e f a c e Preface xiii
Audience xiii
Document Conventions xiii
Documentation Feedback xv
C H A P T E R 1 Using the CLI 1
About the ACI Switch CLI 1
iBash and VSH 1
Bash Conventions and Extensions 2
C H A P T E R 2 C Commands 3
clear counters 4
C H A P T E R 3 D Commands 5
debug reset interface 6
C H A P T E R 4 F Commands 7
faults 8
C H A P T E R 5 H Commands 9
health 10
C H A P T E R 6 I Commands 11
iping 12
iping6 14
itraceroute 15
Cisco ACI Switch Command Reference, NX-OS Release 13.x iii
itraceroute6 vrf 16
itraceroute6 vrf encap vlan 17
itraceroute6 vrf encap vxlan dst-mac 18
itraceroute vrf 19
itraceroute vrf encap vlan 20
itraceroute vrf encap vxlan 22
C H A P T E R 7 R Commands 25
reload 26
reload fex 27
reload module 28
C H A P T E R 8 S Commands 29
setinservice 38
show 39
show 40
show 41
show aaa 42
show aaa user default-role 43
show adjacency vrf 44
show bfd clients 45
show bfd ipv4 neighbors 46
show bfd ipv6 neighbors 47
show bfd neighbors 48
show bgp convergence 49
show bgp neighbors vrf 50
show bgp process 51
show bgp sessions vrf 52
show bgp summary vrf 53
show bgp vrf 54
show cdp all 56
show cdp entry 57
show cdp global 58
show cdp interface 59
show cdp neighbors 60
Cisco ACI Switch Command Reference, NX-OS Release 13.xiv
Contents
show cdp traffic interface 61
show clock 62
show copp policy 63
show copp policy stats 64
show copyright 65
show cores 66
show dcimgr mem-stats 67
show dcimgr repo eteps 68
show dcimgr repo sclass-maps 69
show dcimgr repo vnid-maps 70
show diagnostic content module 71
show diagnostic result module 72
show diagnostic status module 73
show dot1x 74
show dpp policy 75
show eigrp interfaces 76
show eigrp traffic vrf 77
show endpoint 78
show environment 79
show environment fex 80
show fcoe 81
show fex 82
show fhs bt 83
show fhs counters 85
show fhs features 87
show flow cache 88
show flow exporter 89
show flow hw-profile 90
show flow interface 91
show flow monitor 92
show flow record 93
show flow timers 94
show flow vlan 95
show hardware 96
show hostname 97
Cisco ACI Switch Command Reference, NX-OS Release 13.x v
Contents
show hsrp bfd-sessions 98
show hsrp delay 99
show hsrp + 100
show hsrp summary 101
show interface 102
show interface brief 103
show interface capabilities 104
show interface counters 105
show interface counters 106
show interface counters brief 107
show interface counters detailed 108
show interface counters errors 109
show interface counters errors 110
show interface counters snmp 111
show interface counters snmp 112
show interface debounce 113
show interface description 114
show interface fex-fabric 115
show interface flowcontrol 116
show interface flowcontrol 117
show interface mac-address 118
show interface priority-flow-control 119
show interface snmp-ifindex 120
show interface status 121
show interface status 122
show interface switchport 123
show interface transceiver 124
show interface trunk 125
show interface trunk 126
show inventory 127
show ip arp 128
show ip bgp neighbors vrf 129
show ip bgp nexthop-database 130
show ip bgp nexthop 131
show ip bgp summary vrf 132
Cisco ACI Switch Command Reference, NX-OS Release 13.xvi
Contents
show ip bgp vrf 133
show ip community-list 134
show ip dhcp client 135
show ip dhcp global statistics 136
show ip dhcp relay 137
show ip eigrp event vrf 138
show ip eigrp vrf 139
show ip extcommunity-list 140
show ip igmp gipo joins 141
show ip igmp interface 142
show ip igmp snooping 143
show ip igmp snooping explicit-tracking 144
show ip igmp snooping groups + + 145
show ip igmp snooping lookup-mode 146
show ip igmp snooping mrouter 147
show ip igmp snooping querier 148
show ip igmp snooping statistics 149
show ip igmp vrf all 150
show ip interface 151
show ip mroute 152
show ip msdp count 153
show ip msdp mesh-group 154
show ip msdp + 155
show ip msdp peer 156
show ip msdp policy statistics sa-policy 157
show ip msdp rpf 158
show ip msdp sources 159
show ip msdp summary 160
show ip ospf database 161
show ip ospf database detail 163
show ip ospf interface 165
show ip ospf neighbors 166
show ip ospf route vrf 167
show ip ospf summary-address vrf 168
show ip ospf traffic 169
Cisco ACI Switch Command Reference, NX-OS Release 13.x vii
Contents
show ip ospf vrf 170
show ip pim group-range 171
show ip pim interface 172
show ip pim neighbor 173
show ip pim oif-list 174
show ip pim route 175
show ip pim rp 176
show ip pim statistics 177
show ip prefix-list 178
show ip process 179
show ip route 180
show ip static-route 182
show ipsec sa 183
show ipv6 bgp neighbors vrf 184
show ipv6 bgp nexthop-database 185
show ipv6 bgp nexthop 186
show ipv6 dhcp relay 187
show ipv6 icmp adjacency 188
show ipv6 icmp interface 189
show ipv6 interface 190
show ipv6 mld snooping 191
show ipv6 mld snooping explicit-tracking 192
show ipv6 mld snooping groups 193
show ipv6 mld snooping lookup-mode 194
show ipv6 mld snooping mrouter 195
show ipv6 mld snooping querier 196
show ipv6 mld snooping statistics 197
show ipv6 nd interface 198
show ipv6 prefix-list 199
show ipv6 process 200
show ipv6 route + vrf 201
show ipv6 static-route 203
show isis adjacency vrf 204
show isis database vrf 205
show isis dteps vrf 206
Cisco ACI Switch Command Reference, NX-OS Release 13.xviii
Contents
show isis interface vrf 207
show isis protocol vrf 208
show isis route vrf 209
show isis statistics vrf 210
show isis traffic vrf 211
show lacp counters 212
show lacp interface 213
show lacp neighbor 214
show lacp port-channel 215
show lacp system-identifier 216
show lldp dcbx interface 217
show lldp entry 218
show lldp interface 219
show lldp neighbors 220
show lldp timers 221
show lldp tlv-select 222
show lldp traffic 223
show locator-led status 224
show logging ip access-list cache 225
show logging ip access-list drop-codes 226
show logging ip access-list span 227
show mac address-table + 228
show macsec mka session 229
show macsec mka statistics 230
show macsec mka summary 231
show macsec secy statistics 232
show module 233
show module fex 234
show monitor 235
show monitor session 236
show npv external-interface-usage 237
show npv flogi-table 238
show npv flogi-table interface 239
show npv status 240
show npv traffic-map 241
Cisco ACI Switch Command Reference, NX-OS Release 13.x ix
Contents
show ntp authentication-keys 242
show ntp authentication-status 243
show ntp peer-status 244
show ntp peers 245
show ntp statistics peer ipaddr 246
show ntp trusted-keys 247
show ospfv3 database 248
show ospfv3 database detail 250
show ospfv3 interface 252
show ospfv3 neighbors 253
show ospfv3 route vrf 254
show ospfv3 summary-address vrf 255
show ospfv3 traffic 256
show ospfv3 vrf 257
show port-channel capacity 258
show port-channel database 259
show port-channel extended 260
show port-channel summary 261
show port-channel traffic 262
show port-channel usage 263
show porttrack 264
show processes 265
show processes cpu 266
show processes cpu sort 267
show processes memory 268
show ptp brief 269
show ptp clock 270
show ptp clock foreign-masters record 271
show ptp corrections 272
show ptp counters 273
show ptp parent 275
show publickey 276
show radius-server 277
show redundancy status 278
show route-map 279
Cisco ACI Switch Command Reference, NX-OS Release 13.xx
Contents
show san-port-channel database 280
show san-port-channel summary 281
show san-port-channel usage 282
show service copy info 283
show service redir info 284
show snmp 285
show snmp community 286
show snmp context 287
show snmp engineID 288
show snmp host 289
show snmp summary 290
show snmp user 291
show sprom 292
show switchname 293
show system error-id 294
show system mode 295
show system redundancy status 296
show system reset-reason 297
show system reset-reason fex 298
show system resources 299
show system uptime 300
show tacacs-server 301
show tech-support analytics brief 302
show users 303
show version 304
show version module 305
show vlan 306
show vlan all-ports 307
show vlan brief 308
show vlan fcoe 309
show vlan id 310
show vlan reserved 311
show vlan summary 312
show vpc 313
show vpc consistency-parameters 314
Cisco ACI Switch Command Reference, NX-OS Release 13.x xi
Contents
show vpc orphan-ports 315
show vpc peer-keepalive 316
show vpc role 317
show vpc statistics peer-keepalive 318
show vpc statistics vpc 319
show vrf 320
show vrf interface 321
show vsan 322
show vsan membership 323
show vsan membership interface 324
show vsan usage 325
show zoning-filter 326
show zoning-rule + 327
C H A P T E R 9 T Commands 329
techsupport local 330
A P P E N D I X A Configuring Switch Management 331
Configuring Switch Console Settings 332
A P P E N D I X B Using Boot Loader Commands 333
Using Boot Loader Commands 333
boot (loader command) 334
cmdline (loader command) 335
set gw (loader command) 336
set ip (loader command) 337
Cisco ACI Switch Command Reference, NX-OS Release 13.xxii
Contents
Preface
This preface includes the following sections:
• Audience, page xiii
• Document Conventions, page xiii
• Documentation Feedback, page xv
AudienceThis publication is for network administrators who configure and maintain Cisco Nexus devices.
Document ConventionsCommand descriptions use the following conventions:
DescriptionConvention
Bold text indicates the commands and keywords that you enter literallyas shown.
bold
Italic text indicates arguments for which the user supplies the values.Italic
Square brackets enclose an optional element (keyword or argument).[x]
Square brackets enclosing keywords or arguments separated by a verticalbar indicate an optional choice.
[x | y]
Braces enclosing keywords or arguments separated by a vertical barindicate a required choice.
{x | y}
Nested set of square brackets or braces indicate optional or requiredchoices within optional or required elements. Braces and a vertical barwithin square brackets indicate a required choice within an optionalelement.
[x {y | z}]
Cisco ACI Switch Command Reference, NX-OS Release 13.x xiii
DescriptionConvention
Indicates a variable for which you supply values, in context where italicscannot be used.
variable
A nonquoted set of characters. Do not use quotation marks around thestring or the string will include the quotation marks.
string
Examples use the following conventions:
DescriptionConvention
Terminal sessions and information the switch displays are in screen font.screen font
Information you must enter is in boldface screen font.boldface screen font
Arguments for which you supply values are in italic screen font.italic screen font
Nonprinting characters, such as passwords, are in angle brackets.< >
Default responses to system prompts are in square brackets.[ ]
An exclamation point (!) or a pound sign (#) at the beginning of a lineof code indicates a comment line.
!, #
This document uses the following conventions:
Means reader take note. Notes contain helpful suggestions or references to material not covered in themanual.
Note
Means reader be careful. In this situation, you might do something that could result in equipment damageor loss of data.
Caution
IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before youwork on any equipment, be aware of the hazards involved with electrical circuitry and be familiar withstandard practices for preventing accidents. Use the statement number provided at the end of each warningto locate its translation in the translated safety warnings that accompanied this device.
SAVE THESE INSTRUCTIONS
Warning
Cisco ACI Switch Command Reference, NX-OS Release 13.xxiv
PrefaceDocument Conventions
Documentation FeedbackTo provide technical feedback on this document, or to report an error or omission, please send your commentsto [email protected]. We appreciate your feedback.
Cisco ACI Switch Command Reference, NX-OS Release 13.x xv
PrefaceDocumentation Feedback
Cisco ACI Switch Command Reference, NX-OS Release 13.xxvi
PrefaceDocumentation Feedback
Using the CLI
• About the ACI Switch CLI, page 1
• iBash and VSH, page 1
• Bash Conventions and Extensions, page 2
About the ACI Switch CLITheACI switch command-line interface (CLI) is iBash, which consists of the standard Bash command languageinterpreter shell plus a set of custom commands for ACI switches.
To reach the iBash shell, you must login as admin, and not as root.Note
iBash and VSHVirtual Shell (VSH or vshell), the traditional Cisco NX-OS switch interface, is not a supported mode for ACI.Limited VSH functionality is present by typing vsh in the iBash shell, but its use is not intended for normaloperation. This guide does not describe VSH.
In some situations, it could be necessary to use VSH to obtain process tags for use in an iBash command. Forexample, in NX-OS releases that support multiple OSPF instances, an iBash command such as show ip ospf
database displays output only from the first registered OSPF process. To display output from other OSPFprocesses, you must include a process tag in the command: show ip ospf <ptag> database. You can viewthe running processes and obtain the process tag using a VSH command, as in the following example:
(none)# vsh -c "show cli internal ctags" | grep -i ospf4276 281 119 ospf multipodIn 2450 ready ospf-multipodInternal4278 281 119 ospf default 2455 ready ospf-default4277 282 128 ospfv3 default 2478 ready ospfv3-default
To display the output of the OSPF default process in this example, use the iBash command show ip ospf
default database.
Cisco ACI Switch Command Reference, NX-OS Release 13.x 1
Bash Conventions and ExtensionsBash (Bourne Again SHell) is a Unix shell or command-line interpreter supported by a variety of operatingsystems. You can use the Bash interface to directly access the ACI switches or you can develop Bash shellscripts to automate tasks. Bash provides a variety of command line and scripting features.
For more information about the Bash shell , see http://www.gnu.org/software/bash/bash.html.
Network Naming Conventions
Bash uses a forward slash (/) as a separator for interfaces, network addresses, and other settings.
For example, Ethernet interface number 46 on switch module 1 is represented as Eth1/46.
Command Completion
Bash provides tab completion for standard Linux commands and ACI switch-specific commands. When youpress the Tab key at the end of a command or option abbreviation, Bash displays the command in full or thenext available keyword or argument choice. Bash will also autocomplete unambiguous partial commandarguments.
Bash will autocomplete partial commands without theTab key only after you enter the first level command.For example, show int br will be autocompleted as show interface brief, but sh int br will not beautocompleted.
Note
Command History
The CLI supports the Bash shell history functions. To display the command history, you can use the UpArrow or Down Arrow, as well as the history command.
You can reenter a command in the history by stepping through the history to recall the desired command andpressing Enter. You can also recall a command and change it before you enter it.
In addition, you can directly search for a previous command by pressing Ctrl-r and then typing part of thedesired command until the command is displayed.
Command Help
At any time, you can press theEsc key twice to display the options available at the current state of the commandsyntax. If you have not entered anything at the prompt, pressing theEsc key twice lists all available commandsfor the current command mode. If you have partially entered a command, pressing the Esc key twice lists allthe keywords and arguments available at your current position in the command syntax.
The iBash CLI uses Esc-ESC instead of ? to avoid a conflict with the use of $? as a possible Bash promptshortcut.
Note
Cisco ACI Switch Command Reference, NX-OS Release 13.x2
Using the CLIBash Conventions and Extensions
C Commands
• clear counters, page 4
Cisco ACI Switch Command Reference, NX-OS Release 13.x 3
clear countersclear counters [ { interface { all | type } } ]
Reset functions.clear
Clear counters.counters
Clear interface counters.interface
Clear all interface counters.all
Interface. The values are ethernet, port-channel, mgmt, vlan, vfc,vfc-port-channel.
type
This command clears only the port-related statistics. It does not clear the VLAN counters.Note
Cisco ACI Switch Command Reference, NX-OS Release 13.x4
C Commandsclear counters
D Commands
• debug reset interface, page 6
Cisco ACI Switch Command Reference, NX-OS Release 13.x 5
debug reset interfacedebug reset interface arg0
Syntax Description CLI debug action.debug
Reset interface.reset
Interface to be reset.interface
Interface. The type is interface_mrange. The values are ethernet.arg0
Cisco ACI Switch Command Reference, NX-OS Release 13.x6
D Commandsdebug reset interface
F Commands
• faults, page 8
Cisco ACI Switch Command Reference, NX-OS Release 13.x 7
faultsfaults [ { system | { interface interface-name } | { module mod-id [ port port-id ] } } ] [ history | detail ] [id ]
Syntax Description Display faults.faults
System wide events.system
Interface events.interface
Module events.module
Module id. The type is integer. The range is from 1 to 30.mod-id
Port events.port
Port id. The type is integer. The range is from 1 to 255.port-id
Interface name. The type is interface.interface-name
Historical information.history
Detailed information.detail
Specific fault id information. The type is string.id
Cisco ACI Switch Command Reference, NX-OS Release 13.x8
F Commandsfaults
H Commands
• health, page 10
Cisco ACI Switch Command Reference, NX-OS Release 13.x 9
healthhealth [ { system | { interface interface-name } | { module mod-id [ port port-id ] } } ] [ history ]
Syntax Description Display health info.health
System wide events.system
Interface events.interface
Module events.module
Module id. The type is integer. The range is from 1 to 30.mod-id
Port events.port
Port id. The type is integer. The range is from 1 to 255.port-id
Interface name. The type is interface.interface-name
Historical information.history
Cisco ACI Switch Command Reference, NX-OS Release 13.x10
H Commandshealth
I Commands
• iping, page 12
• iping6, page 14
• itraceroute, page 15
• itraceroute6 vrf, page 16
• itraceroute6 vrf encap vlan, page 17
• itraceroute6 vrf encap vxlan dst-mac, page 18
• itraceroute vrf, page 19
• itraceroute vrf encap vlan, page 20
• itraceroute vrf encap vxlan, page 22
Cisco ACI Switch Command Reference, NX-OS Release 13.x 11
ipingiping [-dDFLnqrv][-V vrf][-c count][-i wait][-p pattern][-s packetsize][-t timeout][-S source] host
Syntax Description Send ping packets.iping
Debug mode.-d
Dump info.-D
Enables the do-not-fragment bit in the IPv4 header.-F
Fill in loopback.-L
Display only numeric info.-n
Quiet output.-q
Do not route packets.-r
Display verbose output.-v
The Virtual Routing and Forwarding (VRF) instance from which to source theping message.
-V vrf
Number of ping packets that are sent to the destination address. The default is5.
-c count
The time interval between sending of ping packets.-i wait
The data pattern of the ping payload. Different data patterns are used totroubleshoot framing errors and clocking problems on serial lines. The defaultis [0xABCD].
-p pattern
Size of the ping packet (in bytes).-s packetsize
Timeout interval. The ping is declared successful only if the ECHO REPLYpacket is received before this time interval.
-t timeout
The IP address or host name to show as source.-S source
The IP address or host name of the destination EP.host
Examples
pod1-leaf1# iping -V overlay-1 10.0.59.154
Cisco ACI Switch Command Reference, NX-OS Release 13.x12
I Commandsiping
PING 10.0.59.154 (10.0.59.154): 56 data bytes64 bytes from 10.0.59.154: icmp_seq=0 ttl=55 time=0.254 ms64 bytes from 10.0.59.154: icmp_seq=1 ttl=55 time=0.256 ms64 bytes from 10.0.59.154: icmp_seq=2 ttl=55 time=0.245 ms64 bytes from 10.0.59.154: icmp_seq=3 ttl=55 time=0.241 ms64 bytes from 10.0.59.154: icmp_seq=4 ttl=55 time=0.23 ms
--- 10.0.59.154 ping statistics ---5 packets transmitted, 5 packets received, 0.00% packet lossround-trip min/avg/max = 0.23/0.245/0.256 ms
Cisco ACI Switch Command Reference, NX-OS Release 13.x 13
I Commandsiping
iping6iping6 [-dDFLngRrv][-V vrf][-c count][-i wait][-p pattern][-s packetsize][-t timeout][-S source] host
Syntax Description iping6
The Virtual Routing and Forwarding (VRF) instance from which to source theping message.
-V vrf
Number of ping packets that are sent to the destination address. The default is5.
-c count
The time interval between sending of ping packets.-i wait
The data pattern of the ping payload. Different data patterns are used totroubleshoot framing errors and clocking problems on serial lines. The defaultis [0xABCD].
-p pattern
Size of the ping packet (in bytes).-s packetsize
Timeout interval. The ping is declared successful only if the ECHO REPLYpacket is received before this time interval.
-t timeout
The IPv6 address or host name to show as source.-S source
The IPv6 address or host name of the destination EP.host
Table 1: Command History
ModificationRelease
This command was introduced.11.2
Examples
pod1-leaf1# iping6 -V overlay-1 2001:0DB8::3/64
Cisco ACI Switch Command Reference, NX-OS Release 13.x14
I Commandsiping6
itracerouteitraceroute dst-ip [ { payload pld-size } ]
Syntax Description itraceroute.itraceroute
Inside fabric.fabric
payload size.payload
Enter destination node IP. The type is ipaddr.dst-ip
Enter payload size: 20-8904 (system will add other headers). The type isinteger. The range is from 20 to 8904.
pld-size
Usage Guidelines Use this command to find multiple paths to a destination leaf from the current leaf. This command will executea trace on the overlay VRF.
The itraceroute command provides the following improvements over traditional traceroute:
• Discovers and reports multiple paths
• Transits only a single probe packet per path
• Reports detailed node information
• Simulates tenant traffic, exploring paths under the applied policies
Examples
pod1-leaf1# itraceroute 10.0.71.61
Node traceroute to 10.0.71.61, infra VRF overlay-1, from [10.0.71.63], payload 56 bytesPath 11: TEP 10.0.71.62 intf eth1/35 0.596 ms2: TEP 10.0.71.61 intf eth1/98 0.392 ms
Path 21: TEP 10.0.71.62 intf eth1/33 0.672 ms2: TEP 10.0.71.61 intf eth1/97 0.432 ms
Path 31: TEP 10.0.71.62 intf eth1/35 0.693 ms2: TEP 10.0.71.61 intf eth1/97 0.484 ms
Path 41: TEP 10.0.71.62 intf eth1/33 0.954 ms2: TEP 10.0.71.61 intf eth1/98 0.824 ms
Cisco ACI Switch Command Reference, NX-OS Release 13.x 15
I Commandsitraceroute
itraceroute6 vrfitraceroute6 dst-ip vrf vrf-name [ { payload pld-size } ]
Syntax Description itraceroute6.itraceroute6
tenant vrf.vrf
tenant vrf name. The type is string.vrf-name
Enter destination IPv6. The type is ipv6.dst-ip
payload size.payload
Enter payload size: 20-8904 (system will add other headers). The type isinteger. The range is from 20 to 8904.
pld-size
Cisco ACI Switch Command Reference, NX-OS Release 13.x16
I Commandsitraceroute6 vrf
itraceroute6 vrf encap vlanitraceroute6 dst-ip vrf vrf-name encap vlan [vlan-encap] [ { payload pld-size } ]
Syntax Description itraceroute6.itraceroute6
tenant vrf.vrf
tenant vrf name. The type is string.vrf-name
Enter destination IPv6. The type is ipv6.dst-ip
source EP encap type.encap
vlan src EP.vlan
payload size.payload
Enter Vlan Encap: 1-4095. The type is integer. The range is from 1 to4095.
vlan-encap
Enter payload size: 20-8904 (system will add other headers). The type isinteger. The range is from 20 to 8904.
pld-size
Cisco ACI Switch Command Reference, NX-OS Release 13.x 17
I Commandsitraceroute6 vrf encap vlan
itraceroute6 vrf encap vxlan dst-macitraceroute6 dst-ip vrf vrf-name encap vxlan [vxlan-encap] dst-mac dst-mac [ { payload pld-size } ]
Syntax Description itraceroute6.itraceroute6
tenant vrf.vrf
tenant vrf name. The type is string.vrf-name
Enter destination EP IPv6. The type is ipv6.dst-ip
Destination EP MAC address.dst-mac
Enter destination EP MAC address. The type is ethernet.dst-mac
source EP encap type.encap
vxlan src EP.vxlan
payload size.payload
Enter VTEPVxLAN encap: 4096-16777215. The type is integer. The rangeis from 4096 to 16777215.
vxlan-encap
Enter payload size: 20-8904 (system will add other headers). The type isinteger. The range is from 20 to 8904.
pld-size
Cisco ACI Switch Command Reference, NX-OS Release 13.x18
I Commandsitraceroute6 vrf encap vxlan dst-mac
itraceroute vrfitraceroute [external] dst-ip vrf vrf-name [ { payload pld-size } ]
Syntax Description itraceroute.itraceroute
tenant vrf.vrf
tenant vrf name. The type is string.vrf-name
Enter destination IP. The type is ipaddr.dst-ip
payload size.payload
Enter payload size: 20-8904 (system will add other headers). The type isinteger. The range is from 20 to 8904.
pld-size
Run itraceroute with 5-Tuple.external
Cisco ACI Switch Command Reference, NX-OS Release 13.x 19
I Commandsitraceroute vrf
itraceroute vrf encap vlanitraceroute [external [ max-ext-hopsmax-ext-hops ] [ ext-timeout-sec ext-timeout-sec ] [ ext-timeout-usecext-timeout-usec ] [ ext-interval-sec ext-interval-sec ] [ ext-interval-usec ext-interval-usec ] ] [src-ip sip]dst-ip vrf vrf-name encap vlan [vlan-encap] [dst-mac dst-mac] [ { payload pld-size } ] [ icmp | { {tcp | udp}[{sport-start sps sport-end spe}] [{dport-start dps dport-end dpe}] } ] [ num-queries np ]
Syntax Description itraceroute.itraceroute
tenant vrf.vrf
tenant vrf name. The type is string.vrf-name
Enter destination IP. The type is ipaddr.dst-ip
source EP encap type.encap
vlan src EP.vlan
payload size.payload
Enter Vlan Encap: 1-4095. The type is integer. The range is from 1 to4095.
vlan-encap
Enter payload size: 20-8904 (system will add other headers). The type isinteger. The range is from 20 to 8904.
pld-size
Run itraceroute with 5-Tuple.external
Source EP IP.src-ip
Enter Source EP IP. The type is ipaddr.sip
Destination EP MAC address.dst-mac
Enter destination EP MAC address. The type is ethernet.dst-mac
Source port start.sport-start
Enter starting source port number: 1-65535. The type is integer. The rangeis from 0 to 65535.
sps
Source port end.sport-end
Enter ending source port number: 1-65535. The type is integer. The rangeis from 0 to 65535.
spe
Destination port start.dport-start
Cisco ACI Switch Command Reference, NX-OS Release 13.x20
I Commandsitraceroute vrf encap vlan
Enter starting Destination port number: 1-65535. The type is integer. Therange is from 0 to 65535.
dps
Destination port end.dport-end
Enter ending Destination port number: 1-65535. The type is integer. Therange is from 0 to 65535.
dpe
Start traceroute with TCP Protocol.tcp
Start traceroute with UDP Protocol.udp
Start traceroute with ICMP Protocol.icmp
Number of paths.num-queries
Enter number of paths. The type is integer. The range is from 1 to 65535.np
Max Hops for External Traceroute.max-ext-hops
Enter max Hops for External Traceroute. The type is integer. The rangeis from 1 to 255.
max-ext-hops
External timeout in sec.ext-timeout-sec
Enter External timeout in sec. The type is integer.ext-timeout-sec
External timeout in usec.ext-timeout-usec
Enter External timeout in usec. The type is integer.ext-timeout-usec
External interval in sec.ext-interval-sec
Enter External interval in sec. The type is integer.ext-interval-sec
External interval in usec.ext-interval-usec
Enter External interval in usec. The type is integer.ext-interval-usec
Cisco ACI Switch Command Reference, NX-OS Release 13.x 21
I Commandsitraceroute vrf encap vlan
itraceroute vrf encap vxlanitraceroute [ external [ max-ext-hopsmax-ext-hops ] [ ext-timeout-sec ext-timeout-sec ] [ ext-timeout-usecext-timeout-usec ] [ ext-interval-sec ext-interval-sec ] [ ext-interval-usec ext-interval-usec ] ] [src-ip sip]dst-ip vrf vrf-name encap vxlan [vxlan-encap] [ dst-mac dst-mac ] [ { payload pld-size } ] [ icmp | { {tcp |udp} [{sport-start sps sport-end spe}] [{dport-start dps dport-end dpe}] } ] [ num-queries np ]
Syntax Description itraceroute.itraceroute
tenant vrf.vrf
tenant vrf name. The type is string.vrf-name
Enter destination EP IP. The type is ipaddr.dst-ip
Destination EP MAC address.dst-mac
Enter destination EP MAC address. The type is ethernet.dst-mac
source EP encap type.encap
vxlan src EP.vxlan
payload size.payload
Enter VTEP VxLAN encap: 4096-16777215. The type is integer. Therange is from 4096 to 16777215.
vxlan-encap
Enter payload size: 20-8904 (system will add other headers). The type isinteger. The range is from 20 to 8904.
pld-size
Run itraceroute with 5-Tuple.external
Source EP IP.src-ip
Enter Source EP IP. The type is ipaddr.sip
Starting source port to use.sport-start
Enter starting source port number to use: 1-65535. The type is integer. Therange is from 0 to 65535.
sps
Ending source port to use.sport-end
Enter ending source port number to use: 1-65535. The type is integer. Therange is from 0 to 65535.
spe
Starting destination port to use.dport-start
Cisco ACI Switch Command Reference, NX-OS Release 13.x22
I Commandsitraceroute vrf encap vxlan
Enter starting Destination port number to use: 1-65535. The type is integer.The range is from 0 to 65535.
dps
Ending Destination port to use.dport-end
Enter ending Destination port number to use: 1-65535. The type is integer.The range is from 0 to 65535.
dpe
Use TCP to send probes.tcp
Use UDP Protocol for traceroute.udp
Use ICMP ECHO to send probes.icmp
Number of probe packets per hop.num-queries
Enter number of probe packets per hop. The type is integer. The range isfrom 1 to 65535.
np
Max Hops for External Traceroute.max-ext-hops
Enter max Hops for External Traceroute. The type is integer. The rangeis from 1 to 255.
max-ext-hops
External timeout in sec.ext-timeout-sec
Enter External timeout in sec. The type is integer.ext-timeout-sec
External timeout in usec.ext-timeout-usec
Enter External timeout in usec. The type is integer.ext-timeout-usec
External interval in sec.ext-interval-sec
Enter External interval in sec. The type is integer.ext-interval-sec
External interval in usec.ext-interval-usec
Enter External interval in usec. The type is integer.ext-interval-usec
Cisco ACI Switch Command Reference, NX-OS Release 13.x 23
I Commandsitraceroute vrf encap vxlan
Cisco ACI Switch Command Reference, NX-OS Release 13.x24
I Commandsitraceroute vrf encap vxlan
R Commands
• reload, page 26
• reload fex, page 27
• reload module, page 28
Cisco ACI Switch Command Reference, NX-OS Release 13.x 25
reloadreload
Syntax Description Reload the chassis.reload
Cisco ACI Switch Command Reference, NX-OS Release 13.x26
R Commandsreload
reload fexreload fex fex_id
Syntax Description Reload Information.reload
Fex.fex
FEX number. The type is integer. The range is from 101 to 199.fex_id
Cisco ACI Switch Command Reference, NX-OS Release 13.x 27
R Commandsreload fex
reload modulereload module module_id
Syntax Description Reload Information.reload
Module.module
<1-30> please enter the module number. The type is string.module_id
Cisco ACI Switch Command Reference, NX-OS Release 13.x28
R Commandsreload module
S Commands
• setinservice, page 38
• show, page 39
• show, page 40
• show, page 41
• show aaa, page 42
• show aaa user default-role, page 43
• show adjacency vrf, page 44
• show bfd clients, page 45
• show bfd ipv4 neighbors, page 46
• show bfd ipv6 neighbors, page 47
• show bfd neighbors, page 48
• show bgp convergence, page 49
• show bgp neighbors vrf, page 50
• show bgp process, page 51
• show bgp sessions vrf, page 52
• show bgp summary vrf, page 53
• show bgp vrf, page 54
• show cdp all, page 56
• show cdp entry, page 57
• show cdp global, page 58
• show cdp interface, page 59
• show cdp neighbors, page 60
• show cdp traffic interface, page 61
• show clock, page 62
Cisco ACI Switch Command Reference, NX-OS Release 13.x 29
• show copp policy, page 63
• show copp policy stats, page 64
• show copyright, page 65
• show cores, page 66
• show dcimgr mem-stats, page 67
• show dcimgr repo eteps, page 68
• show dcimgr repo sclass-maps, page 69
• show dcimgr repo vnid-maps, page 70
• show diagnostic content module, page 71
• show diagnostic result module, page 72
• show diagnostic status module, page 73
• show dot1x, page 74
• show dpp policy, page 75
• show eigrp interfaces, page 76
• show eigrp traffic vrf, page 77
• show endpoint, page 78
• show environment, page 79
• show environment fex, page 80
• show fcoe, page 81
• show fex, page 82
• show fhs bt, page 83
• show fhs counters, page 85
• show fhs features, page 87
• show flow cache, page 88
• show flow exporter, page 89
• show flow hw-profile, page 90
• show flow interface, page 91
• show flow monitor, page 92
• show flow record, page 93
• show flow timers, page 94
• show flow vlan, page 95
• show hardware, page 96
• show hostname, page 97
Cisco ACI Switch Command Reference, NX-OS Release 13.x30
S Commands
• show hsrp bfd-sessions, page 98
• show hsrp delay, page 99
• show hsrp +, page 100
• show hsrp summary, page 101
• show interface, page 102
• show interface brief, page 103
• show interface capabilities, page 104
• show interface counters, page 105
• show interface counters, page 106
• show interface counters brief, page 107
• show interface counters detailed, page 108
• show interface counters errors, page 109
• show interface counters errors, page 110
• show interface counters snmp, page 111
• show interface counters snmp, page 112
• show interface debounce, page 113
• show interface description, page 114
• show interface fex-fabric, page 115
• show interface flowcontrol, page 116
• show interface flowcontrol, page 117
• show interface mac-address, page 118
• show interface priority-flow-control, page 119
• show interface snmp-ifindex, page 120
• show interface status, page 121
• show interface status, page 122
• show interface switchport, page 123
• show interface transceiver, page 124
• show interface trunk, page 125
• show interface trunk, page 126
• show inventory, page 127
• show ip arp, page 128
• show ip bgp neighbors vrf, page 129
• show ip bgp nexthop-database, page 130
Cisco ACI Switch Command Reference, NX-OS Release 13.x 31
S Commands
• show ip bgp nexthop, page 131
• show ip bgp summary vrf, page 132
• show ip bgp vrf, page 133
• show ip community-list, page 134
• show ip dhcp client, page 135
• show ip dhcp global statistics, page 136
• show ip dhcp relay, page 137
• show ip eigrp event vrf, page 138
• show ip eigrp vrf, page 139
• show ip extcommunity-list, page 140
• show ip igmp gipo joins, page 141
• show ip igmp interface, page 142
• show ip igmp snooping, page 143
• show ip igmp snooping explicit-tracking, page 144
• show ip igmp snooping groups + +, page 145
• show ip igmp snooping lookup-mode, page 146
• show ip igmp snooping mrouter, page 147
• show ip igmp snooping querier, page 148
• show ip igmp snooping statistics, page 149
• show ip igmp vrf all, page 150
• show ip interface, page 151
• show ip mroute, page 152
• show ip msdp count, page 153
• show ip msdp mesh-group, page 154
• show ip msdp +, page 155
• show ip msdp peer, page 156
• show ip msdp policy statistics sa-policy, page 157
• show ip msdp rpf, page 158
• show ip msdp sources, page 159
• show ip msdp summary, page 160
• show ip ospf database, page 161
• show ip ospf database detail, page 163
• show ip ospf interface, page 165
Cisco ACI Switch Command Reference, NX-OS Release 13.x32
S Commands
• show ip ospf neighbors , page 166
• show ip ospf route vrf, page 167
• show ip ospf summary-address vrf, page 168
• show ip ospf traffic, page 169
• show ip ospf vrf, page 170
• show ip pim group-range, page 171
• show ip pim interface, page 172
• show ip pim neighbor, page 173
• show ip pim oif-list, page 174
• show ip pim route, page 175
• show ip pim rp, page 176
• show ip pim statistics, page 177
• show ip prefix-list, page 178
• show ip process, page 179
• show ip route, page 180
• show ip static-route, page 182
• show ipsec sa, page 183
• show ipv6 bgp neighbors vrf, page 184
• show ipv6 bgp nexthop-database, page 185
• show ipv6 bgp nexthop, page 186
• show ipv6 dhcp relay, page 187
• show ipv6 icmp adjacency, page 188
• show ipv6 icmp interface, page 189
• show ipv6 interface, page 190
• show ipv6 mld snooping, page 191
• show ipv6 mld snooping explicit-tracking, page 192
• show ipv6 mld snooping groups, page 193
• show ipv6 mld snooping lookup-mode, page 194
• show ipv6 mld snooping mrouter, page 195
• show ipv6 mld snooping querier, page 196
• show ipv6 mld snooping statistics, page 197
• show ipv6 nd interface, page 198
• show ipv6 prefix-list, page 199
Cisco ACI Switch Command Reference, NX-OS Release 13.x 33
S Commands
• show ipv6 process, page 200
• show ipv6 route + vrf, page 201
• show ipv6 static-route, page 203
• show isis adjacency vrf, page 204
• show isis database vrf, page 205
• show isis dteps vrf, page 206
• show isis interface vrf, page 207
• show isis protocol vrf, page 208
• show isis route vrf, page 209
• show isis statistics vrf, page 210
• show isis traffic vrf, page 211
• show lacp counters, page 212
• show lacp interface, page 213
• show lacp neighbor, page 214
• show lacp port-channel, page 215
• show lacp system-identifier, page 216
• show lldp dcbx interface, page 217
• show lldp entry, page 218
• show lldp interface, page 219
• show lldp neighbors, page 220
• show lldp timers, page 221
• show lldp tlv-select, page 222
• show lldp traffic, page 223
• show locator-led status, page 224
• show logging ip access-list cache, page 225
• show logging ip access-list drop-codes, page 226
• show logging ip access-list span, page 227
• show mac address-table +, page 228
• show macsec mka session, page 229
• show macsec mka statistics, page 230
• show macsec mka summary, page 231
• show macsec secy statistics, page 232
• show module, page 233
Cisco ACI Switch Command Reference, NX-OS Release 13.x34
S Commands
• show module fex, page 234
• show monitor, page 235
• show monitor session, page 236
• show npv external-interface-usage, page 237
• show npv flogi-table, page 238
• show npv flogi-table interface, page 239
• show npv status, page 240
• show npv traffic-map, page 241
• show ntp authentication-keys, page 242
• show ntp authentication-status, page 243
• show ntp peer-status, page 244
• show ntp peers, page 245
• show ntp statistics peer ipaddr, page 246
• show ntp trusted-keys, page 247
• show ospfv3 database, page 248
• show ospfv3 database detail, page 250
• show ospfv3 interface, page 252
• show ospfv3 neighbors , page 253
• show ospfv3 route vrf, page 254
• show ospfv3 summary-address vrf, page 255
• show ospfv3 traffic, page 256
• show ospfv3 vrf, page 257
• show port-channel capacity, page 258
• show port-channel database, page 259
• show port-channel extended, page 260
• show port-channel summary, page 261
• show port-channel traffic, page 262
• show port-channel usage, page 263
• show porttrack, page 264
• show processes, page 265
• show processes cpu, page 266
• show processes cpu sort, page 267
• show processes memory, page 268
Cisco ACI Switch Command Reference, NX-OS Release 13.x 35
S Commands
• show ptp brief, page 269
• show ptp clock, page 270
• show ptp clock foreign-masters record, page 271
• show ptp corrections, page 272
• show ptp counters, page 273
• show ptp parent, page 275
• show publickey, page 276
• show radius-server, page 277
• show redundancy status, page 278
• show route-map, page 279
• show san-port-channel database, page 280
• show san-port-channel summary, page 281
• show san-port-channel usage, page 282
• show service copy info, page 283
• show service redir info, page 284
• show snmp, page 285
• show snmp community, page 286
• show snmp context, page 287
• show snmp engineID, page 288
• show snmp host, page 289
• show snmp summary, page 290
• show snmp user, page 291
• show sprom, page 292
• show switchname, page 293
• show system error-id, page 294
• show system mode, page 295
• show system redundancy status, page 296
• show system reset-reason, page 297
• show system reset-reason fex, page 298
• show system resources, page 299
• show system uptime, page 300
• show tacacs-server, page 301
• show tech-support analytics brief, page 302
Cisco ACI Switch Command Reference, NX-OS Release 13.x36
S Commands
• show users, page 303
• show version, page 304
• show version module, page 305
• show vlan, page 306
• show vlan all-ports, page 307
• show vlan brief, page 308
• show vlan fcoe, page 309
• show vlan id, page 310
• show vlan reserved, page 311
• show vlan summary, page 312
• show vpc, page 313
• show vpc consistency-parameters, page 314
• show vpc orphan-ports, page 315
• show vpc peer-keepalive, page 316
• show vpc role, page 317
• show vpc statistics peer-keepalive, page 318
• show vpc statistics vpc, page 319
• show vrf, page 320
• show vrf interface, page 321
• show vsan, page 322
• show vsan membership, page 323
• show vsan membership interface, page 324
• show vsan usage, page 325
• show zoning-filter, page 326
• show zoning-rule +, page 327
Cisco ACI Switch Command Reference, NX-OS Release 13.x 37
S Commands
setinservicesetinservice
Syntax Description Put the node ports back in service.setinservice
Cisco ACI Switch Command Reference, NX-OS Release 13.x38
S Commandssetinservice
showshow { { ip eigrp {topology | route} [prefix | active | pending | zero-successors | all-links] vrf {vrf-name |all} } | { ipv6 eigrp {topology | route} [ipv6-prefix | active | pending | zero-successors | all-links] vrf{vrf-name | all} } }
Syntax Description Show running system information.show
Display EIGRP information for IPv4 address family.ip
Show EIGRP information.eigrp
Display information on EIGRP topology (routes).topology
Display information on EIGRP routes.route
Show Information on Active Routes only.active
Show Information on only the Routes pending on any replies.pending
Show Information on only the Routes having Zero Successors.zero-successors
Show all Nexthops of a Route, not just Feasible Successors.all-links
Show information on this Prefix only. The type is ipprefix.prefix
Show information on this ipv6 Prefix only. The type is ipv6_prefix.ipv6-prefix
Show EIGRP information per-VRF.vrf
Name of the VRF. The type is string.vrf-name
Show EIGRP information for all VRF.all
Display EIGRP information for IPv6 address family.ipv6
Cisco ACI Switch Command Reference, NX-OS Release 13.x 39
S Commandsshow
showshow { { ip eigrp neighbors [detail] {iface0 | { [ address ] vrf {vrf-name| all} }}} | { ipv6 eigrp neighbors[detail] {iface0 | { [ ipv6-address] vrf {vrf-name| all} }}}}
Syntax Description Show running system information.show
Display EIGRP information for IPv4 address family.ip
Display EIGRP information for IPv6 address family.ipv6
Show EIGRP information.eigrp
Display information on EIGRP neighbors (peers).neighbors
Show detailed Information on Neighbors.detail
Show Peers on this interface only. The type is interface. The values are ethernet,port-channel, vlan, loopback.
iface0
Peer Address. The type is ipaddr.address
ipv6 Peer Address. The type is ipv6.ipv6-address
Show EIGRP information per-VRF.vrf
Name of the VRF. The type is string.vrf-name
Show EIGRP information for all VRF.all
Cisco ACI Switch Command Reference, NX-OS Release 13.x40
S Commandsshow
showshow [path]
Syntax Description Show Command.show
directory of the mo. The type is string.path
Cisco ACI Switch Command Reference, NX-OS Release 13.x 41
S Commandsshow
show aaashow aaa {authentication | groups}
Syntax Description Show Information.show
Authentication, Authorization and Accounting Information.aaa
Authentication.authentication
Groups.groups
Cisco ACI Switch Command Reference, NX-OS Release 13.x42
S Commandsshow aaa
show aaa user default-roleshow aaa user default-role
Syntax Description Show Information.show
Authentication, Authorization and Accounting configuration mode.aaa
User.user
Default role assigned by aaa-admin for remote authentication.default-role
Cisco ACI Switch Command Reference, NX-OS Release 13.x 43
S Commandsshow aaa user default-role
show adjacency vrfshow { ip | ipv6 } adjacency [ { interface | ip-addr } ] [ detail | summary | non-best ] vrf { vrf-name | all }
Syntax Description Show running system information.show
Display IP information.ip
Display IPv6 information.ipv6
Display adjacency table.adjacency
Display specific interface adjacencies only. The type is interface.interface
Show adjacency summary.summary
IPV4 source address. The type is ipaddr.ip-addr
Show both best/non-best entries.non-best
Show detail information of adjacency entries.detail
Display per-VRF information.vrf
VRF name. The type is string.vrf-name
Show adjacency entries for all vrfs.all
Cisco ACI Switch Command Reference, NX-OS Release 13.x44
S Commandsshow adjacency vrf
show bfd clientsshow bfd clients
Syntax Description Show running system information.show
BFD commands.bfd
Bfd client list.clients
Cisco ACI Switch Command Reference, NX-OS Release 13.x 45
S Commandsshow bfd clients
show bfd ipv4 neighborsshow bfd ipv4 neighbors [{modulemodule_no}] [{interface intf_id}] [{application bfd_cli_client_names}][{src-ip src_ip}] [{dest-ip dest_ip}] [{vrf {vrf-name | all}}] [details] [sort-by {src-ip | dest-ip | interface}]
Syntax Description Show running system information.show
BFD commands.bfd
Ipv4 neighbors.ipv4
Neighbors.neighbors
Module.module
module number. The type is uinteger. to 32. The range is from 0module_no
Interface.interface
show bfd sessions based on interface id. The type is interface. Thevalues are ethernet, loopback, vlan, tunnel.
intf_id
Application.application
Application name. The type is string.bfd_cli_client_names
Source ip.src-ip
Source ip value. The type is ipaddr.src_ip
Destination ip.dest-ip
Destination ip value. The type is ipaddr.dest_ip
Display per-VRF information.vrf
VRF name. The type is string.vrf-name
Display information for all VRFs.all
Details.details
Sort by.sort-by
Cisco ACI Switch Command Reference, NX-OS Release 13.x46
S Commandsshow bfd ipv4 neighbors
show bfd ipv6 neighborsshow bfd ipv6 neighbors [{modulemodule_no}] [{interface intf_id}] [{application bfd_cli_client_names}][{src-ip src_ipv6}] [{dest-ip dest_ipv6}] [{vrf {vrf-name | all}}] [details] [sort-by {src-ip | dest-ip | interface}]
Syntax Description Show running system information.show
BFD commands.bfd
Ipv6 neighbors.ipv6
Neighbors.neighbors
Module.module
module number. The type is uinteger. to 32. The range is from 0module_no
Interface.interface
show bfd sessions based on interface id. The type is interface. Thevalues are ethernet, loopback, vlan, tunnel.
intf_id
Application.application
Application name. The type is string.bfd_cli_client_names
Source ip.src-ip
Source ipv6 value. The type is ipv6.src_ipv6
Destination ip.dest-ip
Destination ipv6 value. The type is ipv6.dest_ipv6
Display per-VRF information.vrf
VRF name. The type is string.vrf-name
Display information for all VRFs.all
Details.details
Sort by.sort-by
Cisco ACI Switch Command Reference, NX-OS Release 13.x 47
S Commandsshow bfd ipv6 neighbors
show bfd neighborsshow bfd neighbors [{module module_no}] [{interface intf_id}] [{application bfd_cli_client_names}][{src-ip src_ip}] [{dest-ip dest_ip}] [{vrf {vrf-name | all}}] [details] [sort-by {src-ip | dest-ip | interface}]
Syntax Description Show running system information.show
BFD commands.bfd
Neighbors.neighbors
Module.module
module number. The type is uinteger. to 32. The range is from 0module_no
Interface.interface
show bfd sessions based on interface id. The type is interface. Thevalues are ethernet, loopback, vlan, tunnel.
intf_id
Application.application
Application name. The type is string.bfd_cli_client_names
Source ip.src-ip
Source ip value. The type is ipaddr.src_ip
Source ipv6 value. The type is ipv6.src_ipv6
Destination ip.dest-ip
Destination ip value. The type is ipaddr.dest_ip
Destination ipv6 value. The type is ipv6.dest_ipv6
Display per-VRF information.vrf
VRF name. The type is string.vrf-name
Display information for all VRFs.all
Details.details
Sort by.sort-by
Cisco ACI Switch Command Reference, NX-OS Release 13.x48
S Commandsshow bfd neighbors
show bgp convergenceshow bgp convergence [detail] [{vrf {vrf-name | ALL_VRFS_012345678901234}}]
Syntax Description Show running system information.show
Display BGP status and configuration.bgp
Display BGP status and configuration.convergence
Display detailed information about convergence.detail
Virtual Router Context.vrf
The type is string. VRF name.vrf-name
all.ALL_VRFS_012345678901234
Cisco ACI Switch Command Reference, NX-OS Release 13.x 49
S Commandsshow bgp convergence
show bgp neighbors vrfshow bgp { { { ipv4 | ipv6 | vpnv4 | vpnv6 } unicast } | { l2vpn evpn } | all } neighbors [neighbor-id |neighbor-prefix-id | ipv6-neighbor-id | ipv6-neighbor-prefix-id] vrf { vrf-name | ALL_VRFS_012345678901234}
Syntax Description Show running system information.show
Show BGP information.bgp
Display BGP information for IPv4 address family.ipv4
Display BGP information for IPv6 address family.ipv6
Display BGP information for VPNv4 address family.vpnv4
Display BGP information for VPNv6 address family.vpnv6
Display BGP information for IPv4 unicast address family.unicast
Display BGP information for L2VPN EVPN address family.l2vpn
Display BGP information for L2VPN EVPN address family.evpn
Display BGP information for all address families.all
Display BGP neighbor information.neighbors
The type is ipaddr. IPv4 neighbor address.neighbor-id
The type is ipprefix. IPv4 prefix neighbor address.neighbor-prefix-id
The type is ipv6. IPv6 neighbor address.ipv6-neighbor-id
The type is ipv6_prefix. IPv6 prefix neighbor address.ipv6-neighbor-prefix-id
Show BGP information for a VRF.vrf
all.ALL_VRFS_012345678901234
Name of the VRF. The type is string.vrf-name
Cisco ACI Switch Command Reference, NX-OS Release 13.x50
S Commandsshow bgp neighbors vrf
show bgp processshow bgp [{vrf {vrf-name | ALL_VRFS_012345678901234}}] process [detail] [{vrf {vrf-name |ALL_VRFS_012345678901234}}]
Syntax Description Show running system information.show
Display BGP status and configuration.bgp
Virtual Router Context.vrf
The type is string. VRF name.vrf-name
all.ALL_VRFS_012345678901234
BGP global information.process
Detailed information.detail
Cisco ACI Switch Command Reference, NX-OS Release 13.x 51
S Commandsshow bgp process
show bgp sessions vrfshow bgp sessions vrf { all | vrf-name }
Syntax Description Show running system information.show
Show BGP information.bgp
Show BGP sessions.sessions
Show BGP sessions in a VRF.vrf
Show BGP sessions for all VRFs.all
Name of the VRF. The type is string.vrf-name
Cisco ACI Switch Command Reference, NX-OS Release 13.x52
S Commandsshow bgp sessions vrf
show bgp summary vrfshow bgp { { { ipv4 | ipv6 | vpnv4 | vpnv6 } unicast } | { l2vpn evpn } | all } summary vrf { vrf-name |ALL_VRFS_012345678901234 }
Syntax Description Show running system information.show
Show BGP information.bgp
Display BGP information for IPv4 address family.ipv4
Display BGP information for IPv6 address family.ipv6
Display BGP information for VPNv4 address family.vpnv4
Display BGP information for VPNv6 address family.vpnv6
Display BGP information for IPv4 unicast address family.unicast
Display BGP information for L2VPN EVPN address family.l2vpn
Display BGP information for L2VPN EVPN address family.evpn
Display BGP information for all address families.all
Display summarized information of BGP state.summary
Show BGP information for a VRF.vrf
all.ALL_VRFS_012345678901234
Name of the VRF. The type is string.vrf-name
Cisco ACI Switch Command Reference, NX-OS Release 13.x 53
S Commandsshow bgp summary vrf
show bgp vrfshow bgp { { { ipv4 | vpnv4 } unicast [ip-prefix]} | { { ipv6 | vpnv6 } unicast [ipv6-prefix]} | { l2vpn evpn[ipv4-rt | ipv6-rt | mac-address | {route-type rtype} | {smad [{source src-v4-addr | src-v6-addr }] [{groupgrp-v4-addr | grp-v6-addr } ] [ {originator orig-v4-addr | orig-v6-addr }] } ] } } vrf {vrf-name |ALL_VRFS_012345678901234}
Syntax Description Show running system information.show
Display BGP status and configuration.bgp
Display BGP information for IPv4 address family.ipv4
Display BGP information for IPv6 address family.ipv6
Display BGP information for VPNv4 address family.vpnv4
Display BGP information for VPNv6 address family.vpnv6
Display unicast SAFI information.unicast
Display BGP information for L2VPN EVPN address family.l2vpn
Display BGP information for L2VPN EVPN address family.evpn
The type is ipprefix. IP address.ip-prefix
The type is ipv6_prefix. IPv6 prefix.ipv6-prefix
The type is ipaddr. IP address.ipv4-rt
The type is ipv6. IPv6 address.ipv6-rt
The type is ethernet. MAC address.mac-address
EVPN route type number.route-type
The type is uinteger. EVPN route type number. The range is from 1 to6.
rtype
EVPN SMAD routes.smad
EVPN SMAD route source.source
The type is ipaddr. IP address.src-v4-addr
The type is ipv6. IPv6 address.src-v6-addr
EVPN SMAD route group.group
Cisco ACI Switch Command Reference, NX-OS Release 13.x54
S Commandsshow bgp vrf
The type is ipaddr. IP address.grp-v4-addr
The type is ipv6. IPv6 address.grp-v6-addr
EVPN SMAD route originator.originator
The type is ipaddr. IP address.orig-v4-addr
The type is ipv6. IPv6 address.orig-v6-addr
Virtual Router Context.vrf
The type is string. VRF name.vrf-name
all.ALL_VRFS_012345678901234
Cisco ACI Switch Command Reference, NX-OS Release 13.x 55
S Commandsshow bgp vrf
show cdp allshow cdp all
Syntax Description Show running system information.show
Show Cisco Discovery Protocol information.cdp
Show all interfaces in CDP database.all
Cisco ACI Switch Command Reference, NX-OS Release 13.x56
S Commandsshow cdp all
show cdp entryshow cdp entry { all | { name dev-id } }
Syntax Description Show running system information.show
Show Cisco Discovery Protocol information.cdp
Show CDP entries in database.entry
Show all CDP entries in database.all
Show a specific CDP entry matching a name.name
Device ID (Max Size 256). The type is string.dev-id
Cisco ACI Switch Command Reference, NX-OS Release 13.x 57
S Commandsshow cdp entry
show cdp globalshow cdp global
Syntax Description Show running system information.show
Show Cisco Discovery Protocol information.cdp
Show CDP global parameters.global
Cisco ACI Switch Command Reference, NX-OS Release 13.x58
S Commandsshow cdp global
show cdp interfaceshow cdp interface arg0
Syntax Description Show running system information.show
Show Cisco Discovery Protocol information.cdp
Show CDP parameters for an interface.interface
Interface. The type is interface. The values are ethernet, mgmt.arg0
Cisco ACI Switch Command Reference, NX-OS Release 13.x 59
S Commandsshow cdp interface
show cdp neighborsshow cdp neighbors [ { interface arg0 } ] [ detail ]
Syntax Description Show running system information.show
Show Cisco Discovery Protocol information.cdp
Show CDP neighbors.neighbors
Show CDP neighbors on an interface.interface
Interface. The type is interface. The values are ethernet, mgmt.arg0
Show CDP neighbors detailed.detail
Cisco ACI Switch Command Reference, NX-OS Release 13.x60
S Commandsshow cdp neighbors
show cdp traffic interfaceshow cdp traffic interface arg0
Syntax Description Show running system information.show
Show Cisco Discovery Protocol information.cdp
Show cdp traffic statistics.traffic
Show cdp traffic statistics on an interface.interface
Interface. The type is interface. The values are ethernet, mgmt.arg0
Cisco ACI Switch Command Reference, NX-OS Release 13.x 61
S Commandsshow cdp traffic interface
show clockshow clock
Syntax Description Show running system information.show
Display current Date.clock
Cisco ACI Switch Command Reference, NX-OS Release 13.x62
S Commandsshow clock
show copp policyshow copp policy
Syntax Description Show running system information.show
Control Plane Policing (CoPP) information.copp
CoPP policies.policy
Cisco ACI Switch Command Reference, NX-OS Release 13.x 63
S Commandsshow copp policy
show copp policy statsshow copp policy stats
Syntax Description Show running system information.show
Control Plane Policing (CoPP) information.copp
CoPP policies.policy
CoPP policies packet statistics.stats
Cisco ACI Switch Command Reference, NX-OS Release 13.x64
S Commandsshow copp policy stats
show copyrightshow copyright
Syntax Description Show running system information.show
Copyright information.copyright
Cisco ACI Switch Command Reference, NX-OS Release 13.x 65
S Commandsshow copyright
show coresshow cores [history]
Syntax Description Show information.show
Show all core dumps for the current vdc.cores
Show core dumps history.history
Cisco ACI Switch Command Reference, NX-OS Release 13.x66
S Commandsshow cores
show dcimgr mem-statsshow dcimgr mem-stats
Syntax Description Show running system information.show
Show dci-Mgr information.dcimgr
Show dcimgr memstats.mem-stats
Cisco ACI Switch Command Reference, NX-OS Release 13.x 67
S Commandsshow dcimgr mem-stats
show dcimgr repo etepsshow dcimgr repo eteps
Syntax Description Show running system information.show
Display DCI Mgr information.dcimgr
Display Object Store info.repo
Display Remote site Tunnels endpoints.eteps
Cisco ACI Switch Command Reference, NX-OS Release 13.x68
S Commandsshow dcimgr repo eteps
show dcimgr repo sclass-mapsshow dcimgr repo sclass-maps { [detail | verbose] }
Syntax Description Show running system information.show
Display DCI Mgr information.dcimgr
Display Object Store info.repo
Display Sclass map translations.sclass-maps
Display detailed information.detail
Verbose Display.verbose
Cisco ACI Switch Command Reference, NX-OS Release 13.x 69
S Commandsshow dcimgr repo sclass-maps
show dcimgr repo vnid-mapsshow dcimgr repo vnid-maps { [detail | verbose] }
Syntax Description Show running system information.show
Display DCI Mgr information.dcimgr
Display Object Store info.repo
Display Vnid map translations.vnid-maps
Display detailed information.detail
Verbose Display.verbose
Cisco ACI Switch Command Reference, NX-OS Release 13.x70
S Commandsshow dcimgr repo vnid-maps
show diagnostic content moduleshow diagnostic content module { all | module_id }
Syntax Description Show information.show
Diagnostic commands.diagnostic
Show diagnostic test content.content
Module Keyword.module
Select all module ID.all
Module ID. The type is string.module_id
Cisco ACI Switch Command Reference, NX-OS Release 13.x 71
S Commandsshow diagnostic content module
show diagnostic result moduleshow diagnostic result module { all | { module_id [ { test test_id } ] } } [detail]
Syntax Description Show information.show
Diagnostic commands.diagnostic
Show diagnostic test result.result
Module Keyword.module
Select all module ID.all
Diagnostic test selection.test
Detailed result.detail
Module ID. The type is string.module_id
Test ID. The type is string.test_id
Cisco ACI Switch Command Reference, NX-OS Release 13.x72
S Commandsshow diagnostic result module
show diagnostic status moduleshow diagnostic status module module_id
Syntax Description Show information.show
Diagnostic commands.diagnostic
Show test status(running/enqueued).status
<1-30> Module number.module
Module ID. The type is string.module_id
Cisco ACI Switch Command Reference, NX-OS Release 13.x 73
S Commandsshow diagnostic status module
show dot1xshow dot1x [ all | { interface if-name } ]
Syntax Description Show running system information.show
Show Dot1x information.dot1x
Show Dot1x information for all Interfaces.all
Show Dot1x information for specific interface.interface
Interface. The type is interface. The values are ethernet.if-name
Cisco ACI Switch Command Reference, NX-OS Release 13.x74
S Commandsshow dot1x
show dpp policyshow dpp policy
Syntax Description Show running system information.show
Data Plane Policing (DPP) information.dpp
DPP policies.policy
Cisco ACI Switch Command Reference, NX-OS Release 13.x 75
S Commandsshow dpp policy
show eigrp interfacesshow { ip | ipv6 } eigrp interfaces [brief] { arg0 | { vrf { all | vrf-name } } }
Syntax Description Show running system information.show
Display EIGRP information for IPv4 address family.ip
Display EIGRP information for IPv6 address family.ipv6
Show EIGRP information.eigrp
Display information on EIGRP enabled interface.interfaces
Show only Brief information.brief
Interface. The type is interface. The values are ethernet, port-channel, vlan,loopback.
arg0
Show EIGRP information per-VRF.vrf
Show EIGRP information for all VRF.all
Name of the VRF. The type is string.vrf-name
Cisco ACI Switch Command Reference, NX-OS Release 13.x76
S Commandsshow eigrp interfaces
show eigrp traffic vrfshow { ip | ipv6 } eigrp traffic vrf { all | vrf-name }
Syntax Description Show running system information.show
Display EIGRP information for IPv4 address family.ip
Display EIGRP information for IPv6 address family.ipv6
Show EIGRP information.eigrp
Display EIGRP traffic Statistics.traffic
Show EIGRP information for a VRF.vrf
Show EIGRP information for all VRFs.all
Name of the VRF. The type is string.vrf-name
Cisco ACI Switch Command Reference, NX-OS Release 13.x 77
S Commandsshow eigrp traffic vrf
show endpointshow endpoint [ { { macmac-addr } | { ip ip-addr | ipv6-addr} [ detail ] } | { [ { vrf vrf-name } | { vlan vlan-id} | { interface interface-name } ] [ { summary | detail } ] } ]
Syntax Description End point commands.show
End point.endpoint
Mac address information.mac
IPv4/IPv6 address information.ip
VRF.vrf
VLAN.vlan
Interface.interface
Endpoint summary information.summary
Endpoint detailed information.detail
MAC Address. The type is ethernet.mac-addr
IP address. The type is ipaddr.ip-addr
IPV6 address. The type is ipv6.ipv6-addr
VRF Name. The type is string.vrf-name
VLAN ID. The type is integer. The range is from 1 to 4095.vlan-id
Interface name. The type is interface.interface-name
Cisco ACI Switch Command Reference, NX-OS Release 13.x78
S Commandsshow endpoint
show environmentshow environment [ fan | power | temperature ]
Syntax Description Show Information.show
Environment Information.environment
Fan Information.fan
Power supply Information.power
Sensor Temperature Information.temperature
In the command output of the show environment power command, the Total Power Allocated (budget)summary data will be provided only for Cisco Nexus 9504, 9508, and 9516 modular spine switches. TheTotal Power Allocated (budget) summary data will not be provided for Cisco Nexus 9336 fixed spineswitches or for leaf switches.
Note
Cisco ACI Switch Command Reference, NX-OS Release 13.x 79
S Commandsshow environment
show environment fexshow environment fex { fexid | all } [ { fan | power | temperature } ]
Syntax Description Show running system information.show
System environment information.environment
Show fex environment information.fex
FEX number. The type is integer. The range is from 101 to 199.fexid
Show information for all FEX.all
Fan information.fan
Power capacity and power distribution information.power
Temperature sensor information.temperature
Cisco ACI Switch Command Reference, NX-OS Release 13.x80
S Commandsshow environment fex
show fcoeshow fcoe [ database ]
Syntax Description Show running system information.show
Show FCOE paramaters.fcoe
Show FCOE database.database
Cisco ACI Switch Command Reference, NX-OS Release 13.x 81
S Commandsshow fcoe
show fexshow fex [ { fexid [detail | version | transceiver] } | detail ]
Syntax Description Show running system information.show
Show FEX information.fex
Detailed information.detail
Show FEX.transceiver
Show the software version.version
FEX number. The type is integer. The range is from 101 to 199.fexid
Cisco ACI Switch Command Reference, NX-OS Release 13.x82
S Commandsshow fex
show fhs btshow fhs bt [summary | detailed] { {{all | static | local | data} [ {bd-vlan vlan-id} | {bd-vnid vnid} ] [sclassepg-sclass] [ {ipv4 ipv4-addr | {all-ip}} | {ipv6 ipv6-addr | {all-ip}} ] [mac mac-addr]} | {{arp | dhcpv4} [{bd-vlan vlan-id} | {bd-vnid vnid} ] [sclass epg-sclass] [ {ipv4 ipv4-addr | {all-ip}} ] [macmac-addr]} | {{nd| dhcpv6} [ {bd-vlan vlan-id} | {bd-vnid vnid} ] [sclass epg-sclass] [ {ipv6 ipv6-addr | {all-ip}} ] [macmac-addr]} }
Syntax Description Show running system information.show
Show information about SISF.fhs
Show SISF binding table information.bt
Show SISF binding table summary information.summary
detailed information.detailed
all protocol entries.all
arp entries.arp
dhcpv4 entries.dhcpv4
nd entries.nd
dhcpv6 entries.dhcpv6
static entries.static
local entries.local
data entries.data
bridge domain encap.bd-vlan
bridge domain vnid.bd-vnid
bd vlan. The type is integer. The range is from 1 to 4095.vlan-id
bd vnid. The type is integer. The range is from 0 to 16777215.vnid
epg sclass.sclass
epg sclass. The type is integer. The range is from 1 to 65534.epg-sclass
ipv4 address family.ipv4
ipv6 address family.ipv6
Cisco ACI Switch Command Reference, NX-OS Release 13.x 83
S Commandsshow fhs bt
ipv4 address. The type is ipaddr.ipv4-addr
ipv6 address. The type is ipv6.ipv6-addr
all ip addresses.all-ip
mac address.mac
mac address. The type is ethernet.mac-addr
Cisco ACI Switch Command Reference, NX-OS Release 13.x84
S Commandsshow fhs bt
show fhs countersshow fhs counters { {arp {request|reply|all}} | {dhcpv4{ack|decline|discover|inform|leaseactive|leasequery|leaseunassigned|leaseunknown|nack|offer|release|request|all}}| {nd {na|ns|ra|redirect|rs|all}} | {dhcpv6{advertise|confirm|decline|informationreq|rebind|reconfigure|relayforw|relayreply|release|renew|reply|request|solicit|all}}| {all} } [ {bd-vlan vlan-id} | {bd-vnid vnid} ]
Syntax Description Show running system information.show
Show information about SISF.fhs
Show SISF counters.counters
arp protocol.arp
dhcpv4 protocol.dhcpv4
neighbour discovery protocol.nd
dhcpv6 protocol.dhcpv6
request counters.request
reply counters.reply
all counters.all
acknowledgment counters.ack
decline counters.decline
discover counters.discover
inform counters.inform
leaseactive counters.leaseactive
leasequery counters.leasequery
leaseunassigned counters.leaseunassigned
leaseunknown counters.leaseunknown
negative acknowledgment counters.nack
offer counters.offer
release counters.release
Cisco ACI Switch Command Reference, NX-OS Release 13.x 85
S Commandsshow fhs counters
neighbor advert counters.na
neighbor solicit counters.ns
router advert counters.ra
redirect counters.redirect
router solicit counters.rs
advertise counters.advertise
confirm counters.confirm
information request counters.informationreq
rebind counters.rebind
reconfigure counters.reconfigure
relay forward counters.relayforw
relay reply counters.relayreply
renew counters.renew
solicit counters.solicit
bridge domain encap.bd-vlan
bridge domain vnid.bd-vnid
bd vlan. The type is integer. The range is from 1 to 4095.vlan-id
bd vnid. The type is integer. The range is from 0 to 16777215.vnid
Cisco ACI Switch Command Reference, NX-OS Release 13.x86
S Commandsshow fhs counters
show fhs featuresshow fhs features { {all} | {ipinspect-v4} | {ipinspect-v6} | {raguard} | {srcguard} } [ {bd-vlan vlan-id} |{bd-vnid vnid} ]
Syntax Description Show running system information.show
Show information about SISF.fhs
Show SISF feature.features
all features.all
ipv4inpsect.ipinspect-v4
ipv6inpsect.ipinspect-v6
routerguard.raguard
sourceguard.srcguard
bridge domain encap.bd-vlan
bridge domain vnid.bd-vnid
bd vlan. The type is integer. The range is from 1 to 4095.vlan-id
bd vnid. The type is integer. The range is from 0 to 16777215.vnid
Cisco ACI Switch Command Reference, NX-OS Release 13.x 87
S Commandsshow fhs features
show flow cacheshow flow cache [ipv4 | ipv6 | ce]
Syntax Description Show running system information.show
Show NetFlow information.flow
Show NetFlow Exporter Cache.cache
Show ipv4 cache entries.ipv4
Show ipv6 cache entries.ipv6
Show ce cache entries.ce
Cisco ACI Switch Command Reference, NX-OS Release 13.x88
S Commandsshow flow cache
show flow exportershow flow exporter
Syntax Description Show running system information.show
Show NetFlow information.flow
Show NetFlow Exporter Configuration and Statistics.exporter
Cisco ACI Switch Command Reference, NX-OS Release 13.x 89
S Commandsshow flow exporter
show flow hw-profileshow flow hw-profile
Syntax Description Show running system information.show
Show information about netflow.flow
Hardware Profile.hw-profile
Cisco ACI Switch Command Reference, NX-OS Release 13.x90
S Commandsshow flow hw-profile
show flow interfaceshow flow interface
Syntax Description Show running system information.show
Show NetFlow information.flow
Flow interface information.interface
Cisco ACI Switch Command Reference, NX-OS Release 13.x 91
S Commandsshow flow interface
show flow monitorshow flow monitor
Syntax Description Show running system information.show
Show NetFlow information.flow
Show Monitor Configuration.monitor
Cisco ACI Switch Command Reference, NX-OS Release 13.x92
S Commandsshow flow monitor
show flow recordshow flow record
Syntax Description Show running system information.show
Show NetFlow information.flow
Show Record Configuration.record
Cisco ACI Switch Command Reference, NX-OS Release 13.x 93
S Commandsshow flow record
show flow timersshow flow timers
Syntax Description Show running system information.show
Show NetFlow information.flow
Show Timer Values.timers
Cisco ACI Switch Command Reference, NX-OS Release 13.x94
S Commandsshow flow timers
show flow vlanshow flow vlan
Syntax Description Show running system information.show
Show NetFlow information.flow
Flow vlan information.vlan
Cisco ACI Switch Command Reference, NX-OS Release 13.x 95
S Commandsshow flow vlan
show hardwareshow hardware
Syntax Description Show running system information.show
Show hardware information.hardware
Cisco ACI Switch Command Reference, NX-OS Release 13.x96
S Commandsshow hardware
show hostnameshow hostname
Syntax Description Show running system information.show
Hostname.hostname
Cisco ACI Switch Command Reference, NX-OS Release 13.x 97
S Commandsshow hostname
show hsrp bfd-sessionsshow hsrp bfd-sessions [interface interface-id [to {addr_v4 | addr_v6}]] [ipv4 | ipv6]
Syntax Description Show running system information.show
Hot Standby Router Protocol (HSRP) information.hsrp
BFD sessions.bfd-sessions
Interface.interface
The type is interface. Interface. The values are ethernet, port-channel, vlan.interface-id
To IP address.to
IPv4 destination address for BFD session. The type is ipaddr.addr_v4
IPv6 destination address for BFD session. The type is ipv6.addr_v6
IPv4 groups only.ipv4
IPv6 groups only.ipv6
Cisco ACI Switch Command Reference, NX-OS Release 13.x98
S Commandsshow hsrp bfd-sessions
show hsrp delayshow hsrp delay [{interface interface-id}]
Syntax Description Show running system information.show
Hot Standby Router Protocol (HSRP) information.hsrp
Groups on this interface.interface
The type is interface. Interface. The values are ethernet, port-channel, vlan.interface-id
Group initialisation delay.delay
Cisco ACI Switch Command Reference, NX-OS Release 13.x 99
S Commandsshow hsrp delay
show hsrp +show hsrp [{interface interface-id}] [{group group-number}] [{active | init | learn | listen | speak | standby}]+ [all] [{brief [all1]} | {stats}] [{ipv4 | ipv6}]
Syntax Description Show running system information.show
Hot Standby Router Protocol (HSRP) information.hsrp
Groups on this interface.interface
The type is interface. Interface. The values are ethernet, port-channel,vlan.
interface-id
Groups in active state.active
Groups in init state.init
Groups in learn state.learn
Groups in listen state.listen
Groups in speak state.speak
Groups in standby state.standby
Group number.group
The type is integer. Group Number. The range is from 0 to 4095.group-number
Include groups in disabled state.all
Brief output.brief
HSRP packet stats output.stats
HSRP V4 Groups.ipv4
HSRP V6 Groups.ipv6
Brief output.all1
Cisco ACI Switch Command Reference, NX-OS Release 13.x100
S Commandsshow hsrp +
show hsrp summaryshow hsrp summary
Syntax Description Show running system information.show
Hot Standby Router Protocol (HSRP) information.hsrp
Show HSRP summary.summary
Cisco ACI Switch Command Reference, NX-OS Release 13.x 101
S Commandsshow hsrp summary
show interfaceshow interface [ arg0 ]
Syntax Description Show running system information.show
Interface.interface
Interface. The type is interface_mrange.arg0
Cisco ACI Switch Command Reference, NX-OS Release 13.x102
S Commandsshow interface
show interface briefshow interface [ arg0 ] brief
Syntax Description Show running system information.show
Interface.interface
Interface. The type is interface_mrange.arg0
Show brief info of interface.brief
Cisco ACI Switch Command Reference, NX-OS Release 13.x 103
S Commandsshow interface brief
show interface capabilitiesshow interface [ arg0 ] capabilities
Syntax Description Show running system information.show
Interface.interface
Ethernet Interface. The type is interface_mrange. The values are ethernet.arg0
Show interface capabilities information.capabilities
Cisco ACI Switch Command Reference, NX-OS Release 13.x104
S Commandsshow interface capabilities
show interface countersshow interface arg0 counters
Syntax Description Show running system information.show
Show interface status and information.interface
Interface. The type is interface_mrange. The values are ethernet, port-channel,vlan, mgmt, vfc, vfc-port-channel.
arg0
Show interface counters.counters
Cisco ACI Switch Command Reference, NX-OS Release 13.x 105
S Commandsshow interface counters
show interface countersshow interface counters [ { fex fex-id } | { module mod-id } ]
Syntax Description Show running system information.show
Show interface status and information.interface
Show interface counters.counters
Enter fex ID.fex
Enter FEX number. The type is integer. The range is from 101 to 199.fex-id
Limit display to interfaces on module.module
Enter module number. The type is integer. The range is from 1 to 30.mod-id
Cisco ACI Switch Command Reference, NX-OS Release 13.x106
S Commandsshow interface counters
show interface counters briefshow interface arg0 counters brief
Syntax Description Show running system information.show
Show interface status and information.interface
Interface. The type is interface_mrange. The values are ethernet, port-channel,vfc, vfc-port-channel.
arg0
Show interface counters.counters
Show interface counters in brief.brief
Cisco ACI Switch Command Reference, NX-OS Release 13.x 107
S Commandsshow interface counters brief
show interface counters detailedshow interface [ arg0 ] counters detailed [ { all [ snmp ] } | snmp ]
Syntax Description Show running system information.show
Show interface status and information.interface
Interface. The type is interface_mrange. The values are ethernet, port-channel,vlan, mgmt, vfc, vfc-port-channel.
arg0
Show interface counters.counters
Show only non-zero counters.detailed
Show every interface counter.all
Show SNMP MIB values.snmp
Cisco ACI Switch Command Reference, NX-OS Release 13.x108
S Commandsshow interface counters detailed
show interface counters errorsshow interface arg0 counters errors
Syntax Description Show running system information.show
Show interface status and information.interface
Interface. The type is interface_mrange. The values are ethernet, port-channel,mgmt.
arg0
Show interface counters.counters
Show interface error counters.errors
Cisco ACI Switch Command Reference, NX-OS Release 13.x 109
S Commandsshow interface counters errors
show interface counters errorsshow interface counters errors [ { fex fex-id } | { module mod-id } ]
Syntax Description Show running system information.show
Show interface status and information.interface
Show interface counters.counters
Show interface error counters.errors
Enter fex ID.fex
Enter FEX number. The type is integer. The range is from 101 to 199.fex-id
Limit display to interfaces on module.module
Enter module number. The type is integer. The range is from 1 to 30.mod-id
Cisco ACI Switch Command Reference, NX-OS Release 13.x110
S Commandsshow interface counters errors
show interface counters snmpshow interface arg0 counters snmp
Syntax Description Show running system information.show
Show interface status and information.interface
Interface. The type is interface_mrange. The values are ethernet, port-channel,vlan, mgmt.
arg0
Show interface counters.counters
Show SNMP MIB values.snmp
Cisco ACI Switch Command Reference, NX-OS Release 13.x 111
S Commandsshow interface counters snmp
show interface counters snmpshow interface counters snmp [ { fex fex-id } | { module mod-id } ]
Syntax Description Show running system information.show
Show interface status and information.interface
Show interface counters.counters
Show SNMP MIB values.snmp
Enter fex ID.fex
Enter FEX number. The type is integer. The range is from 101 to 199.fex-id
Limit display to interfaces on module.module
Enter module number. The type is integer. The range is from 1 to 30.mod-id
Cisco ACI Switch Command Reference, NX-OS Release 13.x112
S Commandsshow interface counters snmp
show interface debounceshow interface [ arg0 ] debounce
Syntax Description Show running system information.show
Show interface status and information.interface
Interface. The type is interface_mrange. The values are ethernet.arg0
Show interface debounce time information.debounce
Cisco ACI Switch Command Reference, NX-OS Release 13.x 113
S Commandsshow interface debounce
show interface descriptionshow interface [ arg0 ] description
Syntax Description Show running system information.show
Interface.interface
Interface. The type is interface_mrange.arg0
Show interface description.description
Cisco ACI Switch Command Reference, NX-OS Release 13.x114
S Commandsshow interface description
show interface fex-fabricshow interface fex-fabric
Syntax Description Show running system information.show
Show interface status and information.interface
Show all FEX fabric ports.fex-fabric
Cisco ACI Switch Command Reference, NX-OS Release 13.x 115
S Commandsshow interface fex-fabric
show interface flowcontrolshow interface arg0 flowcontrol
Syntax Description Show running system information.show
Show interface status and information.interface
Interface. The type is interface_mrange. The values are ethernet, port-channel.arg0
Show interface flowcontrol information.flowcontrol
Cisco ACI Switch Command Reference, NX-OS Release 13.x116
S Commandsshow interface flowcontrol
show interface flowcontrolshow interface flowcontrol [ { fex fex-id } | { module mod-id } ]
Syntax Description Show running system information.show
Show interface status and information.interface
Show interface flowcontrol information.flowcontrol
Limit display to interfaces on a FEX.fex
Enter FEX number. The type is integer. The range is from 101 to 164.fex-id
Limit display to interfaces on module.module
Enter module number. The type is integer. The range is from 1 to 30.mod-id
Cisco ACI Switch Command Reference, NX-OS Release 13.x 117
S Commandsshow interface flowcontrol
show interface mac-addressshow interface [ arg0 ] mac-address
Syntax Description Show running system information.show
Show interface status and information.interface
Interface. The type is interface_mrange. The values are ethernet, port-channel,vlan, mgmt.
arg0
Show interface MAC address.mac-address
Cisco ACI Switch Command Reference, NX-OS Release 13.x118
S Commandsshow interface mac-address
show interface priority-flow-controlshow interface [ arg0 ] priority-flow-control [ details ]
Syntax Description Show running system information.show
Show interface status and information.interface
Ethernet Interface. The type is interface_mrange. The values are ethernet.arg0
Show interface PFC information.priority-flow-control
Show interface PFC detail information.details
Cisco ACI Switch Command Reference, NX-OS Release 13.x 119
S Commandsshow interface priority-flow-control
show interface snmp-ifindexshow interface snmp-ifindex
Syntax Description Show running system information.show
Show interface status and information.interface
Show snmp ifindex list.snmp-ifindex
Cisco ACI Switch Command Reference, NX-OS Release 13.x120
S Commandsshow interface snmp-ifindex
show interface statusshow interface arg0 status [ err-disabled | err-vlans ]
Syntax Description Show running system information.show
Show interface status and information.interface
Interface. The type is interface_mrange. The values are ethernet,port-channel, vlan, mgmt, loopback, tunnel.
arg0
Show interface line status.status
Show interface error disabled state.err-disabled
Show errored vlans.err-vlans
Cisco ACI Switch Command Reference, NX-OS Release 13.x 121
S Commandsshow interface status
show interface statusshow interface status [ down | err-disabled | err-vlans | { fex fex-id } | inactive | { module mod-id } | up ]
Syntax Description Show running system information.show
Show interface status and information.interface
Show interface line status.status
Show interface down state.down
Show interface error disabled state.err-disabled
Show errored vlans.err-vlans
Limit display to interfaces on a FEX.fex
Enter FEX number. The type is integer. The range is from 101 to 164.fex-id
Show interface inactive state.inactive
Limit display to interfaces on module.module
Enter module number. The type is integer. The range is from 1 to 30.mod-id
Show interface up state.up
Cisco ACI Switch Command Reference, NX-OS Release 13.x122
S Commandsshow interface status
show interface switchportshow interface [ arg0 ] switchport
Syntax Description Show running system information.show
Show interface status and information.interface
Interface. The type is interface_mrange. The values are ethernet, port-channel.arg0
Show interface switchport information.switchport
Cisco ACI Switch Command Reference, NX-OS Release 13.x 123
S Commandsshow interface switchport
show interface transceivershow interface [ arg0 ] transceiver [ fex-fabric ] [ calibrations | details | sprom ]
Syntax Description Show Information.show
Interface.interface
Ethernet Interface. The type is interface_mrange. The values are ethernet.arg0
Transceiver Information.transceiver
Show FEX interface transceiver information.fex-fabric
Show interface transceiver calibration information.calibrations
Show interface transceiver detail information.details
Show interface transceiver sprom information.sprom
Cisco ACI Switch Command Reference, NX-OS Release 13.x124
S Commandsshow interface transceiver
show interface trunkshow interface arg0 trunk
Syntax Description Show running system information.show
Show interface status and information.interface
Interface. The type is interface_mrange. The values are ethernet, port-channel.arg0
Show interface trunk information.trunk
Cisco ACI Switch Command Reference, NX-OS Release 13.x 125
S Commandsshow interface trunk
show interface trunkshow interface trunk [ { vlan vlan-id } | { fex fex-id } | { module mod-id } ]
Syntax Description Show running system information.show
Show interface status and information.interface
Show interface trunk information.trunk
Limit display to interfaces on a FEX.fex
Enter FEX number. The type is integer. The range is from 101 to 164.fex-id
Limit display to interfaces on module.module
Enter module number. The type is integer. The range is from 1 to 30.mod-id
Show per vlan information for trunk.vlan
Enter vlan range. The type is integer_mrange. The range is from 1 to 4095.vlan-id
Cisco ACI Switch Command Reference, NX-OS Release 13.x126
S Commandsshow interface trunk
show inventoryshow inventory [ chassis | fans | power_supply | {module [arg0]} ]
Syntax Description Show running system information.show
System inventory information.inventory
system inventory module information.module
system inventory fan information.fans
system inventory chassis information.chassis
system inventory power supply information.power_supply
please enter the module number. The type is integer. The range is from 1to 30.
arg0
Cisco ACI Switch Command Reference, NX-OS Release 13.x 127
S Commandsshow inventory
show ip arpshow ip arp [ { ip-address | detail | static | interface | { summary [interface] } | { statistics [ interface ] } }] [ { vrf { all | vrf-name } } ]
Syntax Description Show running system information.show
Display IP information.ip
Display ARP table and statistics.arp
Display ARP statistics.statistics
Display Static ARP entries.static
Display ARP adjacency summary.summary
Display detailed information.detail
Display per-VRF information.vrf
Display all VRFs.all
Name of the Interface. The type is interface.interface
Ip Address. The type is ipaddr.ip-address
Name of the VRF. The type is string.vrf-name
Cisco ACI Switch Command Reference, NX-OS Release 13.x128
S Commandsshow ip arp
show ip bgp neighbors vrfshow ip bgp neighbors [ arg0 ] vrf { all | vrf-name }
Syntax Description Show running system information.show
Display BGP information for IPv4 address family.ip
Show BGP information.bgp
Display all configured BGP neighbors.neighbors
Display one particular BGP neighbor. The type is ipaddr.arg0
Show BGP sessions in a VRF.vrf
Show BGP sessions for all VRFs.all
Name of the VRF. The type is string.vrf-name
Cisco ACI Switch Command Reference, NX-OS Release 13.x 129
S Commandsshow ip bgp neighbors vrf
show ip bgp nexthop-databaseshow ip bgp [{ {ipv4 {unicast | multicast}} | all }] nexthop-database[{vrf {vrf-name |ALL_VRFS_012345678901234}}]
Syntax Description Show running system information.show
Display IP information.ip
Display BGP status and configuration.bgp
Display BGP information for IPv4 address family.ipv4
Display BGP information for IPv4 unicast address family.unicast
Display BGP information for IPv4 multicast address family.multicast
Display BGP information for all address families.all
Display nexthop database.nexthop-database
Virtual Router Context.vrf
The type is string. VRF name.vrf-name
all.ALL_VRFS_012345678901234
Cisco ACI Switch Command Reference, NX-OS Release 13.x130
S Commandsshow ip bgp nexthop-database
show ip bgp nexthopshow ip bgp nexthop ipnexthop [{vrf {vrf-name | ALL_VRFS_012345678901234}}]
Syntax Description Show running system information.show
Display IP information.ip
Display BGP status and configuration.bgp
Display routes matching the nexthop.nexthop
The type is ipaddr. Nexthop address.ipnexthop
Virtual Router Context.vrf
The type is string. VRF name.vrf-name
all.ALL_VRFS_012345678901234
Cisco ACI Switch Command Reference, NX-OS Release 13.x 131
S Commandsshow ip bgp nexthop
show ip bgp summary vrfshow {ip | ipv6} bgp summary vrf {vrf-name | ALL_VRFS_012345678901234}
Syntax Description Show running system information.show
Display IP information.ip
Display IPv6 information.ipv6
Display BGP status and configuration.bgp
Show summary information.summary
Virtual Router Context.vrf
The type is string. VRF name.vrf-name
all.ALL_VRFS_012345678901234
Cisco ACI Switch Command Reference, NX-OS Release 13.x132
S Commandsshow ip bgp summary vrf
show ip bgp vrfshow ip bgp {ip-addr|ip-prefix} vrf vrf-name
Syntax Description Show running system information.show
Display IP information.ip
Display BGP status and configuration.bgp
The type is ipaddr. IP address.ip-addr
The type is ipprefix. IP prefix.ip-prefix
Virtual Router Context.vrf
The type is string. VRF name.vrf-name
Cisco ACI Switch Command Reference, NX-OS Release 13.x 133
S Commandsshow ip bgp vrf
show ip community-listshow ip community-list [ strarg ]
Syntax Description Show running system information.show
Display IP information.ip
List community-list.community-list
Name of prefix list (Max Size 100). The type is string.strarg
Cisco ACI Switch Command Reference, NX-OS Release 13.x134
S Commandsshow ip community-list
show ip dhcp clientshow ip dhcp client [ statistics [ { interface intfname } ] ]
Syntax Description Show running system information.show
Display IP information.ip
Show items in DHCP.dhcp
DHCP client.client
Statistics related to DHCP.statistics
DHCP client address of the interface.interface
Slot/chassis number. The type is interface. The values are ethernet,port-channel, vlan, loopback.
intfname
Cisco ACI Switch Command Reference, NX-OS Release 13.x 135
S Commandsshow ip dhcp client
show ip dhcp global statisticsshow ip dhcp global statistics
Syntax Description Show running system information.show
Display IP information.ip
Show items in DHCP.dhcp
DHCP global stats.global
Statistics related to DHCP.statistics
Cisco ACI Switch Command Reference, NX-OS Release 13.x136
S Commandsshow ip dhcp global statistics
show ip dhcp relayshow ip dhcp relay [ { { statistics [ { interface intfname } ] } | { address [ { detail | { interface intfname [detail ] } } ] } | { discover [ { interface intfname } ] } | detail } ]
Syntax Description Show running system information.show
Display IP information.ip
Show items in DHCP.dhcp
DHCP Relay.relay
DHCP relay address.address
DHCP relay node discovery.discover
Statistics related to DHCP.statistics
DHCP relay detailed information.detail
DHCP relay address of the interface.interface
Slot/chassis number. The type is interface. The values are ethernet,port-channel, vlan, loopback.
intfname
Cisco ACI Switch Command Reference, NX-OS Release 13.x 137
S Commandsshow ip dhcp relay
show ip eigrp event vrfshow {ip|ipv6} eigrp event vrf {vrf-name | all}
Syntax Description Show running system information.show
Display IP information.ip
Display IPv6 information.ipv6
Display EIGRP status and configuration.eigrp
IP-EIGRP Events.event
Virtual Router Context.vrf
The type is string. VRF name.vrf-name
Display information for all VRFs.all
Cisco ACI Switch Command Reference, NX-OS Release 13.x138
S Commandsshow ip eigrp event vrf
show ip eigrp vrfshow {ip|ipv6} eigrp [detail] vrf {vrf-name | all}
Syntax Description Show running system information.show
Display IP information.ip
Display IPv6 information.ipv6
Display EIGRP status and configuration.eigrp
Display detailed information.detail
Virtual Router Context.vrf
The type is string. VRF name.vrf-name
Display information for all VRFs.all
Cisco ACI Switch Command Reference, NX-OS Release 13.x 139
S Commandsshow ip eigrp vrf
show ip extcommunity-listshow ip extcommunity-list [ strarg ]
Syntax Description Show running system information.show
Display IP information.ip
List extcommunity-list.extcommunity-list
Name of prefix list (Max Size 100). The type is string.strarg
Cisco ACI Switch Command Reference, NX-OS Release 13.x140
S Commandsshow ip extcommunity-list
show ip igmp gipo joinsshow ip igmp gipo joins
Syntax Description Show running system information.show
Display IP information.ip
Display IGMP status and configuration.igmp
Show IGMP gipo information.gipo
Show IGMP gipo Join Summary.joins
Cisco ACI Switch Command Reference, NX-OS Release 13.x 141
S Commandsshow ip igmp gipo joins
show ip igmp interfaceshow ip igmp interface [intf] [brief] [vrf {vrf-name | all}]
Syntax Description Show running system information.show
Show IP information.ip
IGMP protocol events.igmp
IGMP Interface.interface
Display neighbors on single interface name. The type is interface. The valuesare brief, ethernet, loopback, port-channel, tunnel, vlan, vrf.
intf
Display properties on single IGMP interface in brief.brief
Display per-VRF information.vrf
VRF name (Max Size 32).vrf-name
Display information for all VRFs.all
Cisco ACI Switch Command Reference, NX-OS Release 13.x142
S Commandsshow ip igmp interface
show ip igmp snoopingshow ip igmp snooping [ { vlan vlan } ] [ extended ]
Syntax Description Show running system information.show
Show IP information.ip
Show IGMP information.igmp
IGMP Snooping information.snooping
Display Vlan IGMP snooping membership information.vlan
Display Extended Vlan IGMP snooping membership information.extended
Specify vlan-id. The type is integer. The range is from 1 to 4095.vlan
Cisco ACI Switch Command Reference, NX-OS Release 13.x 143
S Commandsshow ip igmp snooping
show ip igmp snooping explicit-trackingshow ip igmp snooping explicit-tracking [ { vlan vlan } ] [ encap ] [ extended ]
Syntax Description Show running system information.show
Show IP information.ip
Show IGMP information.igmp
IGMP Snooping information.snooping
Display explicit-tracking database for IGMPv3.explicit-tracking
Display Vlan explicit-tracking database.vlan
Display Encap Vlan explicit-tracking database.encap
Display Extended Vlan explicit-tracking database.extended
Specify vlan-id. The type is integer. The range is from 1 to 4095.vlan
Cisco ACI Switch Command Reference, NX-OS Release 13.x144
S Commandsshow ip igmp snooping explicit-tracking
show ip igmp snooping groups + +show ip igmp snooping groups [ group | source ]+ [ { vlan vlan } ] [ encap ] [ extended ] [ detail | summary]+
Syntax Description Show running system information.show
Show IP information.ip
Show IGMP information.igmp
Show IGMP Snooping information.snooping
Display snooping information for group address.groups
Multicast IP address of single group to display. The type is ipaddr.group
Source IP address. The type is ipaddr.source
Display detailed information for the group.detail
Display snooping group summary.summary
Display Vlan IGMP snooping membership information.vlan
Display Encap Vlan IGMP snooping membership information.encap
Display Extended Vlan IGMP snooping membership information.extended
Specify vlan-id. The type is integer. The range is from 1 to 4095.vlan
Cisco ACI Switch Command Reference, NX-OS Release 13.x 145
S Commandsshow ip igmp snooping groups + +
show ip igmp snooping lookup-modeshow ip igmp snooping lookup-mode [ { vlan vlan } ] [ extended ]
Syntax Description Show running system information.show
Show IP information.ip
Show IGMP information.igmp
IGMP Snooping information.snooping
IGMP Snooping lkup mode information.lookup-mode
Display Vlan information.vlan
Display Extended Vlan IGMP snooping lkup mode information.extended
Specify vlan-id. The type is integer. The range is from 1 to 4095.vlan
Cisco ACI Switch Command Reference, NX-OS Release 13.x146
S Commandsshow ip igmp snooping lookup-mode
show ip igmp snooping mroutershow ip igmp snooping mrouter [ { vlan vlan } ] [ encap ] [ extended ] [ detail ]
Syntax Description Show running system information.show
Show IP information.ip
Show IGMP information.igmp
IGMP Snooping information.snooping
Display multicast routers detected.mrouter
Display detailed mrouter information.detail
Display Vlan multicast router information.vlan
Display Encap Vlan IGMP snooping mrouter information.encap
Display Extended Vlan IGMP snooping mrouter information.extended
Specify vlan-id. The type is integer. The range is from 1 to 4095.vlan
Cisco ACI Switch Command Reference, NX-OS Release 13.x 147
S Commandsshow ip igmp snooping mrouter
show ip igmp snooping queriershow ip igmp snooping querier [ { vlan vlan } ] [ extended ] [ detail ]
Syntax Description Show running system information.show
Show IP information.ip
Show IGMP information.igmp
IGMP Snooping information.snooping
Display snooping querier information.querier
Display detailed information.detail
Display Vlan IGMP snooping querier information.vlan
Display Extended Vlan IGMP snooping Querier information.extended
Specify vlan-id. The type is integer. The range is from 1 to 4095.vlan
Cisco ACI Switch Command Reference, NX-OS Release 13.x148
S Commandsshow ip igmp snooping querier
show ip igmp snooping statisticsshow ip igmp snooping statistics [ { vlan vlan } ] [ extended ] [ global ]
Syntax Description Show running system information.show
Show IP information.ip
Show IGMP information.igmp
IGMP Snooping information.snooping
Display packet/error counter statistics.statistics
Display global statistics.global
Display vlan statistics.vlan
Display Extended Vlan IGMP snooping statistics information.extended
Specify vlan-id. The type is integer. The range is from 1 to 4095.vlan
Cisco ACI Switch Command Reference, NX-OS Release 13.x 149
S Commandsshow ip igmp snooping statistics
show ip igmp vrf allshow ip igmp vrf all
Syntax Description Show running system information.show
Display IP information.ip
Display IGMP status and configuration.igmp
Display per-VRF information.vrf
Display information for all VRFs.all
Cisco ACI Switch Command Reference, NX-OS Release 13.x150
S Commandsshow ip igmp vrf all
show ip interfaceshow ip interface [ {brief [include-secondary]} | interface | ip-addr ] [ operational ] [ { vrf { all | vrf-name} } ]
Syntax Description Show running system information.show
Display IP information.ip
Display IP related interface information.interface
Show brief info of interface.brief
Display summary of all IP addresses.include-secondary
Display only interfaces that are administratively enabled.operational
Display per-VRF information.vrf
Display all VRFs.all
Name of the Interface. The type is interface. The values are ethernet,port-channel, vlan, mgmt, loopback, tunnel.
interface
Ip Address. The type is ipaddr.ip-addr
Name of the VRF. The type is string.vrf-name
Display interface for local IP address. The type is string.local-addr
Cisco ACI Switch Command Reference, NX-OS Release 13.x 151
S Commandsshow ip interface
show ip mrouteshow ip mroute [[detail] | {summary [count | software-forwarded | rpf-failed]} | { [{{group [source][shared-tree | source-tree] }}] {[flags] | [detail] | [summary [software-forwarded | rpf-failed]]}}] [vrf{vrf-name | all}]
Syntax Description Show running system information.show
Show IP information.ip
Display per-VRF information.vrf
Display information for all VRFs.all
Display IP multicast routing table.mroute
Display route counts and packet rates.summary
Display route for *,G entries.shared-tree
Display route for S,G entries.source-tree
Display software switched route counts only.software-forwarded
Display RPF failure statistics.rpf-failed
Source IP address. The type is ipaddr.source
Multicast IP address of single group to display. The type is ipaddr.group
The type is string. VRF name.vrf-name
Display route counts only.count
Display detailed route attributes.detail
Display detailed route attributes.flags
Cisco ACI Switch Command Reference, NX-OS Release 13.x152
S Commandsshow ip mroute
show ip msdp countshow ip msdp count [as-number] [vrf {vrf-name | all }]
Syntax Description Show running system information.show
Show IP information.ip
Display MSDP status and configuration.msdp
Display SA cache counters.count
AS number. The type is asn.as-number
Display per-VRF information.vrf
The type is string. VRF name (Max Size 32).vrf-name
Display information for all VRFs.all
Cisco ACI Switch Command Reference, NX-OS Release 13.x 153
S Commandsshow ip msdp count
show ip msdp mesh-groupshow ip msdp mesh-group [mesh-name] [vrf {vrf-name | all }]
Syntax Description Show running system information.show
Show IP information.ip
Display MSDP status and configuration.msdp
Display members of mesh-group.mesh-group
Display single mesh-group. The type is string.mesh-name
Display per-VRF information.vrf
The type is string. VRF name (Max Size 32).vrf-name
Display information for all VRFs.all
Cisco ACI Switch Command Reference, NX-OS Release 13.x154
S Commandsshow ip msdp mesh-group
show ip msdp +show ip msdp {sa-cache | route} [ group | source ]+ [asn] [{peer ipaddr}] [detail] [vrf {vrf-name | all }]
Syntax Description Show running system information.show
Show IP information.ip
Display MSDP status and configuration.msdp
Display MSDP SA route cache.sa-cache
Display MSDP SA route cache.route
Display group/source address for SA. The type is ipaddr.source
Display group/source address for SA. The type is ipaddr.group
AS number. The type is asn.asn
Display MSDP SA received from single peer.peer
IP address of peer for SA. The type is ipaddr.ipaddr
Display detailed information.detail
Display per-VRF information.vrf
The type is string. VRF name (Max Size 32).vrf-name
Display information for all VRFs.all
Cisco ACI Switch Command Reference, NX-OS Release 13.x 155
S Commandsshow ip msdp +
show ip msdp peershow ip msdp peer [ipaddr] [vrf {vrf-name | all }]
Syntax Description Show running system information.show
Show IP information.ip
Display MSDP status and configuration.msdp
Display MSDP peer information.peer
IP address of MSDP peer. The type is ipaddr.ipaddr
Display per-VRF information.vrf
The type is string. VRF name (Max Size 32).vrf-name
Display information for all VRFs.all
Cisco ACI Switch Command Reference, NX-OS Release 13.x156
S Commandsshow ip msdp peer
show ip msdp policy statistics sa-policyshow ip msdp policy statistics sa-policy ipaddr {in | out} [vrf {vrf-name | all }]
Syntax Description Show running system information.show
Show IP information.ip
Display MSDP status and configuration.msdp
Policy information.policy
Policy statistics.statistics
Configureed SA policy for MSDP peer.sa-policy
IP address of MSDP peer for SA policy. The type is ipaddr.ipaddr
Input policy.in
Output policy.out
Display per-VRF information.vrf
The type is string. VRF name (Max Size 32).vrf-name
Display information for all VRFs.all
Cisco ACI Switch Command Reference, NX-OS Release 13.x 157
S Commandsshow ip msdp policy statistics sa-policy
show ip msdp rpfshow ip msdp rpf [rpaddr] [vrf {vrf-name | all }]
Syntax Description Show running system information.show
Show IP information.ip
Display MSDP status and configuration.msdp
Display RPF-peer for RP address.rpf
IP address of RP. The type is ipaddr.rpaddr
Display per-VRF information.vrf
The type is string. VRF name (Max Size 32).vrf-name
Display information for all VRFs.all
Cisco ACI Switch Command Reference, NX-OS Release 13.x158
S Commandsshow ip msdp rpf
show ip msdp sourcesshow ip msdp sources [vrf {vrf-name | all }]
Syntax Description Show running system information.show
Show IP information.ip
Display MSDP status and configuration.msdp
Display learned sources with their group counts and limits.sources
Display per-VRF information.vrf
The type is string. VRF name (Max Size 32).vrf-name
Display information for all VRFs.all
Cisco ACI Switch Command Reference, NX-OS Release 13.x 159
S Commandsshow ip msdp sources
show ip msdp summaryshow ip msdp summary [vrf {vrf-name | all }]
Syntax Description Show running system information.show
Show IP information.ip
Display MSDP status and configuration.msdp
Display MSDP peer summary.summary
Display per-VRF information.vrf
The type is string. VRF name (Max Size 32).vrf-name
Display information for all VRFs.all
Cisco ACI Switch Command Reference, NX-OS Release 13.x160
S Commandsshow ip msdp summary
show ip ospf databaseshow ip ospf [ptag] database [[[network | asbr-summary | summary | router | opaque-link | opaque-area| nssa-external] [{area area-id-ip}]] | {external [{ext_tag tag_val}]} | opaque-as] [lsid] [self-originated |{adv-router advid} | {adv-router-name adv-name} ] [vrf {vrf-name | all}]
Syntax Description Show running system information.show
Display IP information.ip
Display OSPF status and configuration.ospf
Process tag, when multiple OSPF instances exist.ptag
Link-state Database Summary.database
Display network LSAs.network
Display type 4 (asbr-summary) LSAs.asbr-summary
Display type 3 (network-summary) LSAs.summary
Display router LSAs.router
Display Opaque Link-Local LSAs.opaque-link
Display Opaque Area LSAs.opaque-area
Display type 7 (NSSA external) LSAs.nssa-external
Display only LSA's in this area.area
The type is ipaddr. Area Id as an integer or ip address.area-id-ip
Display type 5 (external) LSAs.external
Restrict display by tag.ext_tag
The type is uinteger. 32-bit tag value.tag_val
Display Opaque AS LSAs.opaque-as
The type is ipaddr. Restrict display by link state ID.lsid
Display only self-originated LSAs.self-originated
Restrict display by Advertising router.adv-router
The type is ipaddr. Advertising router ID.advid
Cisco ACI Switch Command Reference, NX-OS Release 13.x 161
S Commandsshow ip ospf database
Restrict display by Advertising router name.adv-router-name
The type is string. DNS Name of the Advertising router.adv-name
Display per-VRF information.vrf
The type is string. VRF name.vrf-name
Display information for all VRFs.all
Usage Guidelines In NX-OS releases that support multiple OSPF instances, a command such as show ip ospf database displaysoutput only from the first registered OSPF process. To display output from other OSPF processes, you mustinclude a process tag in the command: show ip ospf <ptag> database. You can view the running processesand obtain the process tag using a VSH command, as in the following example:
(none)# vsh -c "show cli internal ctags" | grep -i ospf4276 281 119 ospf multipodIn 2450 ready ospf-multipodInternal4278 281 119 ospf default 2455 ready ospf-default4277 282 128 ospfv3 default 2478 ready ospfv3-default
To display the output of the OSPF default process in this example, use the command show ip ospf default
database.
Cisco ACI Switch Command Reference, NX-OS Release 13.x162
S Commandsshow ip ospf database
show ip ospf database detailshow ip ospf database [[[network | asbr-summary | summary | router | opaque-link | opaque-area |nssa-external] [{area area-id-ip}]] | {external [{ext_tag tag_val}]} | opaque-as] [lsid] [self-originated |{adv-router advid} | {adv-router-name adv-name} ] detail [vrf {vrf-name | all}]
Syntax Description Show running system information.show
Display IP information.ip
Display OSPF status and configuration.ospf
Link-state Database Summary.database
Display network LSAs.network
Display type 4 (asbr-summary) LSAs.asbr-summary
Display type 3 (network-summary) LSAs.summary
Display router LSAs.router
Display Opaque Link-Local LSAs.opaque-link
Display Opaque Area LSAs.opaque-area
Display type 7 (NSSA external) LSAs.nssa-external
Display only LSA's in this area.area
The type is ipaddr. Area Id as an integer or ip address.area-id-ip
Display type 5 (external) LSAs.external
Restrict display by tag.ext_tag
The type is uinteger. 32-bit tag value.tag_val
Display Opaque AS LSAs.opaque-as
The type is ipaddr. Restrict display by link state ID.lsid
Display only self-originated LSAs.self-originated
Restrict display by Advertising router.adv-router
The type is ipaddr. Advertising router ID.advid
Restrict display by Advertising router name.adv-router-name
Cisco ACI Switch Command Reference, NX-OS Release 13.x 163
S Commandsshow ip ospf database detail
The type is string. DNS Name of the Advertising router.adv-name
Display LSA in detail.detail
Display per-VRF information.vrf
The type is string. VRF name.vrf-name
Display information for all VRFs.all
Cisco ACI Switch Command Reference, NX-OS Release 13.x164
S Commandsshow ip ospf database detail
show ip ospf interfaceshow ip ospf interface { arg0 | { [ brief ] vrf { all | vrf-name } } }
Syntax Description Show running system information.show
Ipv4.ip
Display OSPF status and configuration.ospf
OSPF enabled interface.interface
Interface. The type is interface. The values are ethernet, port-channel, vlan,loopback.
arg0
Display summary of OSPF interfaces.brief
Display per-VRF information.vrf
Display information for all VRFs.all
VRF name (Max Size 32). The type is string.vrf-name
Cisco ACI Switch Command Reference, NX-OS Release 13.x 165
S Commandsshow ip ospf interface
show ip ospf neighborsshow ip ospf neighbors { arg0 [ { ip [ detail ] } | detail | summary ] [vrf { all | vrf-name } ] } | { [ { ip [ detail] } | detail | summary ] vrf { all | vrf-name } }
Syntax Description Show running system information.show
Ipv4.ip
Display OSPF status and configuration.ospf
Neighbor list.neighbors
Router ID of neighbor. The type is ipaddr.ip
Show detailed neighbor display.detail
Interface. The type is interface. The values are ethernet, port-channel, vlan,loopback.
arg0
Summary of neighbors.summary
Display per-VRF information.vrf
Display information for all VRFs.all
VRF name (Max Size 32). The type is string.vrf-name
Cisco ACI Switch Command Reference, NX-OS Release 13.x166
S Commandsshow ip ospf neighbors
show ip ospf route vrfshow ip ospf route [ summary | { ippfx [ longer-prefixes ] [ summary ] } | ip ] vrf { all | vrf-name }
Syntax Description Show running system information.show
Ipv4.ip
Display OSPF status and configuration.ospf
Internal OSPF routes.route
Show single OSPF route. The type is ipaddr.ip
Show single exact match OSPF route. The type is ipprefix.ippfx
Show route counts.summary
Show exact match and more specific routes.longer-prefixes
Display per-VRF information.vrf
Display information for all VRFs.all
VRF name (Max Size 32). The type is string.vrf-name
Cisco ACI Switch Command Reference, NX-OS Release 13.x 167
S Commandsshow ip ospf route vrf
show ip ospf summary-address vrfshow ip ospf summary-address vrf { all | vrf-name }
Syntax Description Show running system information.show
Ipv4.ip
Display OSPF status and configuration.ospf
Summary-address redistribution information.summary-address
Display per-VRF information.vrf
Display information for all VRFs.all
VRF name (Max Size 32). The type is string.vrf-name
Cisco ACI Switch Command Reference, NX-OS Release 13.x168
S Commandsshow ip ospf summary-address vrf
show ip ospf trafficshow ip ospf traffic { arg0 | { vrf { all | vrf-name } } }
Syntax Description Show running system information.show
Ipv4.ip
Display OSPF status and configuration.ospf
Packet counters.traffic
Interface. The type is interface. The values are ethernet, port-channel, vlan,loopback.
arg0
Display per-VRF information.vrf
Display information for all VRFs.all
VRF name (Max Size 32). The type is string.vrf-name
Cisco ACI Switch Command Reference, NX-OS Release 13.x 169
S Commandsshow ip ospf traffic
show ip ospf vrfshow ip ospf vrf { all | vrf-name }
Syntax Description Show running system information.show
Ipv4.ip
Display OSPF status and configuration.ospf
Display per-VRF information.vrf
Display information for all VRFs.all
VRF name (Max Size 32). The type is string.vrf-name
Cisco ACI Switch Command Reference, NX-OS Release 13.x170
S Commandsshow ip ospf vrf
show ip pim group-rangeshow ip pim group-range [group] [vrf {vrf-name | all}]
Syntax Description Show running system information.show
Show IP information.ip
Display PIM status and configuration.pim
Display the various group-ranges.group-range
IP address of the group to display. The type is ipaddr.group
Display per-VRF information.vrf
The type is string. VRF name (Max Size 32).vrf-name
Display information for all VRFs.all
Cisco ACI Switch Command Reference, NX-OS Release 13.x 171
S Commandsshow ip pim group-range
show ip pim interfaceshow ip pim interface [intf] [brief] [vrf {vrf-name | all}]
Syntax Description Show running system information.show
Show IP information.ip
Display PIM status and configuration.pim
Display PIM interface related information.interface
Display properties on single PIM interface. The type is interface. The values arebrief, ethernet, loopback, port-channel, tunnel, vlan, vrf.
intf
Display one line status per PIM interface.brief
Display per-VRF information.vrf
The type is string. VRF name (Max Size 32).vrf-name
Display information for all VRFs.all
Cisco ACI Switch Command Reference, NX-OS Release 13.x172
S Commandsshow ip pim interface
show ip pim neighborshow ip pim neighbor {[interface] | [ipaddr]} [vrf {vrf-name | all}]
Syntax Description Show running system information.show
Show IP information.ip
Display PIM status and configuration.pim
Display PIM neighbor related information.neighbor
Display neighbors on single interface name. The type is interface. The valuesare ethernet, loopback, port-channel, tunnel, vlan, vrf.
interface
IP address of single neighbor to display. The type is ipaddr.ipaddr
Display per-VRF information.vrf
The type is string. VRF name (Max Size 32).vrf-name
Display information for all VRFs.all
Cisco ACI Switch Command Reference, NX-OS Release 13.x 173
S Commandsshow ip pim neighbor
show ip pim oif-listshow ip pim oif-list group [source] [vrf {vrf-name | all}]
Syntax Description Show running system information.show
Show IP information.ip
Display PIM status and configuration.pim
Display interfaces for oif-list of PIM route.oif-list
Group address to display. The type is ipaddr.group
Source address to display. The type is ipaddr.source
Display per-VRF information.vrf
The type is string. VRF name (Max Size 32).vrf-name
Display information for all VRFs.all
Cisco ACI Switch Command Reference, NX-OS Release 13.x174
S Commandsshow ip pim oif-list
show ip pim routeshow ip pim route [{group [source]}] [vrf {vrf-name | all }]
Syntax Description Show running system information.show
Show IP information.ip
Display PIM status and configuration.pim
Display PIM route cache.route
Multicast IP address of single group to display. The type is ipaddr.group
Source IP address. The type is ipaddr.source
Display per-VRF information.vrf
The type is string. VRF name (Max Size 32).vrf-name
Display information for all VRFs.all
Cisco ACI Switch Command Reference, NX-OS Release 13.x 175
S Commandsshow ip pim route
show ip pim rpshow ip pim rp [group] [vrf {vrf-name | all}]
Syntax Description Show running system information.show
Show IP information.ip
Display PIM status and configuration.pim
Display PIM RP, Auto-RP, and BSR related information.rp
Display RP for group address. The type is ipaddr.group
Display per-VRF information.vrf
The type is string. VRF name (Max Size 32).vrf-name
Display information for all VRFs.all
Cisco ACI Switch Command Reference, NX-OS Release 13.x176
S Commandsshow ip pim rp
show ip pim statisticsshow ip pim statistics [vrf {vrf-name | all}]
Syntax Description Show running system information.show
Show IP information.ip
Display PIM status and configuration.pim
Display PIM Statistics per-VRF.statistics
Display per-VRF information.vrf
The type is string. VRF name (Max Size 32).vrf-name
Display information for all VRFs.all
Cisco ACI Switch Command Reference, NX-OS Release 13.x 177
S Commandsshow ip pim statistics
show ip prefix-listshow ip prefix-list [ strarg ]
Syntax Description Show running system information.show
Display IP information.ip
List IP prefix lists.prefix-list
Name of prefix list (Max Size 100). The type is string.strarg
Cisco ACI Switch Command Reference, NX-OS Release 13.x178
S Commandsshow ip prefix-list
show ip processshow ip process [ { vrf { all | vrf-name } } ]
Syntax Description Show running system information.show
Display IP information.ip
Display IP global information.process
Display per-VRF information.vrf
Display all VRFs.all
Name of the VRF. The type is string.vrf-name
Cisco ACI Switch Command Reference, NX-OS Release 13.x 179
S Commandsshow ip process
show ip routeshow ip route { { [ ip-addr | { ip-prefix [{longer-prefixes|shorter-prefixes}] } ] [ bgp | eigrp | ospf ] [ {next-hop nh } | { interface intf } | { updated { [ { since stime } ] [ { until utime } ] } } ]+ [ summary | detail] vrf {vrf-name | all} } | { vrf {vrf-name | all} [ ip-addr | { ip-prefix [{longer-prefixes|shorter-prefixes}] } ][ { next-hop nh } | { interface intf } | { updated { [ { since stime } ] [ { until utime } ] } } ]+ [ summary |detail ] } }
Syntax Description Show running system information.show
Display IP information.ip
Display routing information.route
Display single route longest match lookup. The type is ipaddr.ip-addr
Display single exact match route. The type is ipprefix.ip-prefix
Display matching routes with mask-lengths >= prefix.longer-prefixes
Display matching routes with mask-lengths <= prefix.shorter-prefixes
Display routes with this next-hop only.next-hop
Next hop address. The type is ipaddr.nh
Display routes with this output interface only.interface
Interface Name. The type is interface.intf
Display routes filtered by last updated time.updated
Display those routes updated since this time.since
Since this date/time [[CC]YY-][MM-DD-]HH:MM[:SS]. The type is string.stime
Display those routes updated until this time.until
Until this date/time [[CC]YY-][MM-DD-]HH:MM[:SS]. The type is string.utime
Display route counts.summary
Display routes in full detail.detail
Display per-VRF information.vrf
VRF name. The type is string.vrf-name
bgp
Cisco ACI Switch Command Reference, NX-OS Release 13.x180
S Commandsshow ip route
ospf
eigrp
Display information for all VRFs.all
Cisco ACI Switch Command Reference, NX-OS Release 13.x 181
S Commandsshow ip route
show ip static-routeshow ip static-route [ { vrf { all | vrf-name } } ]
Syntax Description Show running system information.show
Display IP information.ip
Display configured static routes.static-route
Display per-VRF information.vrf
Display all VRFs.all
Name of the VRF. The type is string.vrf-name
Cisco ACI Switch Command Reference, NX-OS Release 13.x182
S Commandsshow ip static-route
show ipsec sashow ipsec sa [detail]
Syntax Description Show running system information.show
Show ipsec retaed information.ipsec
Ipsec Security Associations.sa
Ipsec Security Associations detailed information.detail
Cisco ACI Switch Command Reference, NX-OS Release 13.x 183
S Commandsshow ipsec sa
show ipv6 bgp neighbors vrfshow ipv6 bgp neighbors [ arg0 ] vrf { all | vrf-name }
Syntax Description Show running system information.show
Display BGP information for IPv6 address family.ipv6
Show BGP information.bgp
Display all configured BGP neighbors.neighbors
Display one particular BGP neighbor. The type is ipv6.arg0
Show BGP sessions in a VRF.vrf
Show BGP sessions for all VRFs.all
Name of the VRF. The type is string.vrf-name
Cisco ACI Switch Command Reference, NX-OS Release 13.x184
S Commandsshow ipv6 bgp neighbors vrf
show ipv6 bgp nexthop-databaseshow ipv6 bgp nexthop-database [{vrf {vrf-name | ALL_VRFS_012345678901234}}]
Syntax Description Show running system information.show
Display IPv6 information.ipv6
Display BGP status and configuration.bgp
Display nexthop database.nexthop-database
Virtual Router Context.vrf
The type is string. VRF name.vrf-name
all.ALL_VRFS_012345678901234
Cisco ACI Switch Command Reference, NX-OS Release 13.x 185
S Commandsshow ipv6 bgp nexthop-database
show ipv6 bgp nexthopshow ipv6 bgp nexthop ipv6nexthop [{vrf {vrf-name | ALL_VRFS_012345678901234}}]
Syntax Description Show running system information.show
Display IPv6 information.ipv6
Display BGP status and configuration.bgp
Display routes matching the nexthop.nexthop
The type is ipv6. Nexthop address.ipv6nexthop
Virtual Router Context.vrf
The type is string. VRF name.vrf-name
all.ALL_VRFS_012345678901234
Cisco ACI Switch Command Reference, NX-OS Release 13.x186
S Commandsshow ipv6 bgp nexthop
show ipv6 dhcp relayshow ipv6 dhcp relay [ { statistics } | { address [ { detail | { interface intfname [ detail ] } } ] } ]
Syntax Description Show running system information.show
Display IPv6 information.ipv6
Show items in DHCP.dhcp
DHCP Relay.relay
DHCP relay address.address
DHCP relay detailed information.detail
DHCP relay address of the interface.interface
Slot/chassis number. The type is interface. The values are ethernet,port-channel, vlan, loopback.
intfname
Statistics related to DHCP.statistics
Cisco ACI Switch Command Reference, NX-OS Release 13.x 187
S Commandsshow ipv6 dhcp relay
show ipv6 icmp adjacencyshow ipv6 icmp adjacency [interface] [detail] [vrf {vrf-name | all}]
Syntax Description Show running system information.show
Display IPv6 information.ipv6
Display ICMPv6 information.icmp
Show IPv6 dynamic learnt adjacency entry.adjacency
Display detailed information.detail
Display per-VRF information.vrf
Display information for all VRFs.all
Interface name to display. The type is interface.interface
VRF name. The type is string.vrf-name
Cisco ACI Switch Command Reference, NX-OS Release 13.x188
S Commandsshow ipv6 icmp adjacency
show ipv6 icmp interfaceshow ipv6 icmp interface [interface] [detail] [vrf {vrf-name | all}]
Syntax Description Display information for all VRFs.all
Show running system information.show
Show IPv6 dynamic learnt adjacency entry.interface
Display detailed information.detail
Display per-VRF information.vrf
Display IPv6 information.ipv6
Display ICMPv6 information.icmp
Interface name to display. The type is interface.interface
VRF name. The type is string.vrf-name
Cisco ACI Switch Command Reference, NX-OS Release 13.x 189
S Commandsshow ipv6 icmp interface
show ipv6 interfaceshow ipv6 interface [ {brief [include-secondary]} | interface | ipv6-addr ] [ { vrf { all | vrf-name } } ]
Syntax Description Show running system information.show
Display IPv6 information.ipv6
Display IPv6 related interface information.interface
Show brief info of interface.brief
Display summary of all IPv6 addresses.include-secondary
Display only interfaces that are administratively enabled.operational
Display per-VRF information.vrf
Display all VRFs.all
Name of the Interface. The type is interface. The values are ethernet,port-channel, vlan, mgmt, loopback, vrf.
interface
Ipv6 Address. The type is ipv6.ipv6-addr
Name of the VRF. The type is string.vrf-name
Display interface for local IPv6 address. The type is string.local-addr
Cisco ACI Switch Command Reference, NX-OS Release 13.x190
S Commandsshow ipv6 interface
show ipv6 mld snoopingshow ipv6 mld snooping [ { vlan vlan } ]
Syntax Description Show running system information.show
Show IPv6 information.ipv6
Show MLD information.mld
MLD Snooping information.snooping
Display Vlan MLD snooping membership information.vlan
Specify vlan-id. The type is integer. The range is from 1 to 4095.vlan
Cisco ACI Switch Command Reference, NX-OS Release 13.x 191
S Commandsshow ipv6 mld snooping
show ipv6 mld snooping explicit-trackingshow ipv6 mld snooping explicit-tracking [ { vlan vlan } ] [encap]
Syntax Description Show running system information.show
Show IPv6 information.ipv6
Show MLD information.mld
MLD Snooping information.snooping
Display explicit-tracking database for MLDv2.explicit-tracking
Display Vlan explicit-tracking database.vlan
Display Encap Vlan explicit-tracking database.encap
Specify vlan-id. The type is integer. The range is from 1 to 4095.vlan
Cisco ACI Switch Command Reference, NX-OS Release 13.x192
S Commandsshow ipv6 mld snooping explicit-tracking
show ipv6 mld snooping groupsshow ipv6 mld snooping groups [ { [ group ] [ source ] } [ { vlan vlan } ] ] [ detail | summary] [ encap ]
Syntax Description Show running system information.show
Show IPv6 information.ipv6
Show MLD information.mld
Show MLD Snooping information.snooping
Display snooping information for group address.groups
Multicast IP address of single group to display. The type is ipv6.group
Source IP address. The type is ipv6.source
Display detailed information for the group.detail
Display snooping group summary.summary
Display Vlan MLD snooping membership information.vlan
Display Encap Vlan MLD snooping membership information.encap
Specify vlan-id. The type is integer. The range is from 1 to 4095.vlan
Cisco ACI Switch Command Reference, NX-OS Release 13.x 193
S Commandsshow ipv6 mld snooping groups
show ipv6 mld snooping lookup-modeshow ipv6 mld snooping lookup-mode [ { vlan vlan } ]
Syntax Description Show running system information.show
Show IPv6 information.ipv6
Show MLD information.mld
MLD Snooping information.snooping
MLD Snooping lkup mode information.lookup-mode
Display Vlan information.vlan
Specify vlan-id. The type is integer. The range is from 1 to 4095.vlan
Cisco ACI Switch Command Reference, NX-OS Release 13.x194
S Commandsshow ipv6 mld snooping lookup-mode
show ipv6 mld snooping mroutershow ipv6 mld snooping mrouter [ { vlan vlan } ] [detail] [encap]
Syntax Description Show running system information.show
Show IPv6 information.ipv6
Show MLD information.mld
MLD Snooping information.snooping
Display multicast routers detected.mrouter
Display detailed mrouter information.detail
Display Vlan multicast router information.vlan
Display Encap Vlan MLD snooping membership information.encap
Specify vlan-id. The type is integer. The range is from 1 to 4095.vlan
Cisco ACI Switch Command Reference, NX-OS Release 13.x 195
S Commandsshow ipv6 mld snooping mrouter
show ipv6 mld snooping queriershow ipv6 mld snooping querier [ { vlan vlan } ] [detail]
Syntax Description Show running system information.show
Show IPv6 information.ipv6
Show MLD information.mld
MLD Snooping information.snooping
Display snooping querier information.querier
Display detailed information.detail
Display Vlan MLD snooping querier information.vlan
Specify vlan-id. The type is integer. The range is from 1 to 4095.vlan
Cisco ACI Switch Command Reference, NX-OS Release 13.x196
S Commandsshow ipv6 mld snooping querier
show ipv6 mld snooping statisticsshow ipv6 mld snooping statistics [global | { vlan vlan } ]
Syntax Description Show running system information.show
Show IPv6 information.ipv6
Show MLD information.mld
MLD Snooping information.snooping
Display packet/error counter statistics.statistics
Display global statistics.global
Display vlan statistics.vlan
Specify vlan-id. The type is integer. The range is from 1 to 4095.vlan
Cisco ACI Switch Command Reference, NX-OS Release 13.x 197
S Commandsshow ipv6 mld snooping statistics
show ipv6 nd interfaceshow ipv6 nd interface [interface] [detail] [prefix] [vrf {vrf-name | all}]
Syntax Description Display information for all VRFs.all
Show running system information.show
Show IPv6 dynamic learnt adjacency entry.interface
Display detailed information.detail
Display List of ICMPv6 RA prefix.prefix
Display per-VRF information.vrf
Display IPv6 information.ipv6
Display NDinformation.nd
Interface name to display. The type is interface.interface
VRF name. The type is string.vrf-name
Cisco ACI Switch Command Reference, NX-OS Release 13.x198
S Commandsshow ipv6 nd interface
show ipv6 prefix-listshow ipv6 prefix-list [ strarg ]
Syntax Description Show running system information.show
Display IPv6 information.ipv6
List IPv6 prefix lists.prefix-list
Name of prefix list (Max Size 100). The type is string.strarg
Cisco ACI Switch Command Reference, NX-OS Release 13.x 199
S Commandsshow ipv6 prefix-list
show ipv6 processshow ipv6 process [ { vrf { all | vrf-name } } ]
Syntax Description Show running system information.show
Display IP information.ipv6
Display IP global information.process
Display per-VRF information.vrf
Display all VRFs.all
Name of the VRF. The type is string.vrf-name
Cisco ACI Switch Command Reference, NX-OS Release 13.x200
S Commandsshow ipv6 process
show ipv6 route + vrfshow ipv6 route [ ipv6-addr | { ipv6-prefix [{longer-prefixes|shorter-prefixes}] } ] [ bgp | eigrp | ospf ] [{ next-hop next-hop } | { interface interface } | { updated { [since stime ] [until utime] } } ]+ [ summary |detail ] vrf {vrf-name | all}
Syntax Description Show running system information.show
Display IP information.ipv6
Display routing information.route
Display single route longest match lookup. The type is ipv6.ipv6-addr
Display single exact match route. The type is ipv6_prefix.ipv6-prefix
Display matching routes with mask-lengths >= prefix.longer-prefixes
Display matching routes with mask-lengths <= prefix.shorter-prefixes
Display routes with this next-hop only.next-hop
Next hop address. The type is ipv6.next-hop
Display routes with this output interface only.interface
Interface Name. The type is interface.interface
Display routes filtered by last updated time.updated
Display those routes updated since this time.since
Since this date/time [[CC]YY-][MM-DD-]HH:MM[:SS]. The type is string.stime
Display those routes updated until this time.until
Until this date/time [[CC]YY-][MM-DD-]HH:MM[:SS]. The type is string.utime
Display route counts.summary
Display routes in full detail.detail
Display per-VRF information.vrf
VRF name. The type is string.vrf-name
bgp
ospf
Cisco ACI Switch Command Reference, NX-OS Release 13.x 201
S Commandsshow ipv6 route + vrf
eigrp
Display information for all VRFs.all
Cisco ACI Switch Command Reference, NX-OS Release 13.x202
S Commandsshow ipv6 route + vrf
show ipv6 static-routeshow ipv6 static-route [ { vrf { all | vrf-name } } ]
Syntax Description Show running system information.show
Display IP information.ipv6
Display configured static routes.static-route
Display per-VRF information.vrf
Display all VRFs.all
Name of the VRF. The type is string.vrf-name
Cisco ACI Switch Command Reference, NX-OS Release 13.x 203
S Commandsshow ipv6 static-route
show isis adjacency vrfshow isis adjacency [{system-id sid}] [interface] [detail] vrf { all | vrf-name }
Syntax Description Show running system information.show
Display IS-IS status and configuration.isis
Display IS-IS adjacency information.adjacency
IS-IS interface. The type is interface. The values are ethernet.interface
Hostname or System ID.system-id
Hostname or System ID (in the form of XXXX.XXXX.XXXX). The type isstring.
sid
Display IS-IS detail adjacency information.detail
VRF name.vrf
Display information for all VRFs.all
Specify VRF Name. The type is string.vrf-name
Cisco ACI Switch Command Reference, NX-OS Release 13.x204
S Commandsshow isis adjacency vrf
show isis database vrfshow isis database [level-1|l1] [lid] vrf { all | vrf-name }
Syntax Description Show running system information.show
Display IS-IS status and configuration.isis
Display IS-IS database information.database
Display IS-IS Level-1 routing link state database.level-1
Display IS-IS Level-1 routing link state database.l1
LSP ID in the form of XXXX.XXXX.XXXX.XX-XX. The type is lsp_id.lid
VRF name.vrf
Display information for all VRFs.all
Specify VRF Name. The type is string.vrf-name
Cisco ACI Switch Command Reference, NX-OS Release 13.x 205
S Commandsshow isis database vrf
show isis dteps vrfshow isis dteps vrf { all | vrf-name }
Syntax Description Show running system information.show
Display IS-IS status and configuration.isis
ISIS Dynamic Tunnel EndPoint database.dteps
VRF name.vrf
Display information for all VRFs.all
Specify VRF Name. The type is string.vrf-name
Cisco ACI Switch Command Reference, NX-OS Release 13.x206
S Commandsshow isis dteps vrf
show isis interface vrfshow isis interface [ brief | intf_arg ] [level-1] vrf { all | vrf-name }
Syntax Description Show running system information.show
Display IS-IS status and configuration.isis
Display IS-IS interface information.interface
Display Level-1 interfaces.level-1
Brief display of IS-IS interfaces.brief
IS-IS interface. The type is interface. The values are ethernet.intf_arg
VRF name.vrf
Display information for all VRFs.all
Specify VRF Name. The type is string.vrf-name
Cisco ACI Switch Command Reference, NX-OS Release 13.x 207
S Commandsshow isis interface vrf
show isis protocol vrfshow isis protocol vrf { all | vrf-name }
Syntax Description Show running system information.show
Display IS-IS status and configuration.isis
Display IS-IS process information.protocol
VRF name.vrf
Display information for all VRFs.all
Specify VRF Name. The type is string.vrf-name
Cisco ACI Switch Command Reference, NX-OS Release 13.x208
S Commandsshow isis protocol vrf
show isis route vrfshow isis route vrf { all | vrf-name }
Syntax Description Show running system information.show
Display IS-IS status and configuration.isis
Display IS-IS route information.route
VRF name.vrf
Display information for all VRFs.all
Specify VRF Name. The type is string.vrf-name
Cisco ACI Switch Command Reference, NX-OS Release 13.x 209
S Commandsshow isis route vrf
show isis statistics vrfshow isis statistics vrf { all | vrf-name }
Syntax Description Show running system information.show
Display IS-IS status and configuration.isis
Display IS-IS protocol statistics.statistics
VRF name.vrf
Display information for all VRFs.all
Specify VRF Name. The type is string.vrf-name
Cisco ACI Switch Command Reference, NX-OS Release 13.x210
S Commandsshow isis statistics vrf
show isis traffic vrfshow isis traffic [interface] vrf { all | vrf-name }
Syntax Description Show running system information.show
Display IS-IS status and configuration.isis
Display IS-IS traffic information.traffic
IS-IS interface. The type is interface. The values are ethernet.interface
VRF name.vrf
Display information for all VRFs.all
Specify VRF Name. The type is string.vrf-name
Cisco ACI Switch Command Reference, NX-OS Release 13.x 211
S Commandsshow isis traffic vrf
show lacp countersshow lacp counters [ { interface arg0 } ]
Syntax Description Show running system information.show
LACP protocol.lacp
LACP counters.counters
Specify a port-channel.interface
Port Channel interface. The type is interface_mrange. The values areport-channel.
arg0
Cisco ACI Switch Command Reference, NX-OS Release 13.x212
S Commandsshow lacp counters
show lacp interfaceshow lacp interface arg0
Syntax Description Show running system information.show
LACP protocol.lacp
Specify an interface.interface
Interface. The type is interface. The values are ethernet.arg0
Cisco ACI Switch Command Reference, NX-OS Release 13.x 213
S Commandsshow lacp interface
show lacp neighborshow lacp neighbor [ { interface arg0 } ]
Syntax Description Show running system information.show
LACP protocol.lacp
LACP interface neighbor.neighbor
Specify a port-channel.interface
Port Channel interface. The type is interface_mrange. The values areport-channel.
arg0
Cisco ACI Switch Command Reference, NX-OS Release 13.x214
S Commandsshow lacp neighbor
show lacp port-channelshow lacp port-channel [ { interface arg0 } ]
Syntax Description Show running system information.show
LACP protocol.lacp
LACP port-channels.port-channel
Specify a port-channel.interface
Port Channel interface. The type is interface_mrange. The values areport-channel.
arg0
Cisco ACI Switch Command Reference, NX-OS Release 13.x 215
S Commandsshow lacp port-channel
show lacp system-identifiershow lacp system-identifier
Syntax Description Show running system information.show
LACP protocol.lacp
Show system-identifier information.system-identifier
Cisco ACI Switch Command Reference, NX-OS Release 13.x216
S Commandsshow lacp system-identifier
show lldp dcbx interfaceshow lldp dcbx interface if0
Syntax Description Show running system information.show
Show information about lldp.lldp
Show dcbx information.dcbx
show lldp interface information.interface
The type is interface. Enter interface. The values are ethernet.if0
Cisco ACI Switch Command Reference, NX-OS Release 13.x 217
S Commandsshow lldp dcbx interface
show lldp entryshow lldp entry [ sys-name ]
Syntax Description Show running system information.show
Show information about lldp.lldp
Show lldp entry information.entry
Peer's System name. The type is string.sys-name
Cisco ACI Switch Command Reference, NX-OS Release 13.x218
S Commandsshow lldp entry
show lldp interfaceshow lldp interface arg0
Syntax Description Show running system information.show
Show information about lldp.lldp
Show lldp interface information.interface
Interface. The type is interface. The values are ethernet, mgmt.arg0
Cisco ACI Switch Command Reference, NX-OS Release 13.x 219
S Commandsshow lldp interface
show lldp neighborsshow lldp neighbors [ { interface arg0 } ] [ detail ]
Syntax Description Show running system information.show
Show information about lldp.lldp
Show lldp neighbor information.neighbors
Show lldp neighbor information on an interface.interface
Interface. The type is interface. The values are ethernet, mgmt.arg0
Show lldp neighbor detail information.detail
Cisco ACI Switch Command Reference, NX-OS Release 13.x220
S Commandsshow lldp neighbors
show lldp timersshow lldp timers
Syntax Description Show running system information.show
Show information about lldp.lldp
Show lldp timers.timers
Cisco ACI Switch Command Reference, NX-OS Release 13.x 221
S Commandsshow lldp timers
show lldp tlv-selectshow lldp tlv-select
Syntax Description Show running system information.show
Show information about lldp.lldp
Show lldp tlv-select.tlv-select
Cisco ACI Switch Command Reference, NX-OS Release 13.x222
S Commandsshow lldp tlv-select
show lldp trafficshow lldp traffic [ { interface arg0 } ]
Syntax Description Show running system information.show
Show information about lldp.lldp
Show lldp counters.traffic
Show lldp interface information.interface
Interface. The type is interface. The values are ethernet, mgmt.arg0
Cisco ACI Switch Command Reference, NX-OS Release 13.x 223
S Commandsshow lldp traffic
show locator-led statusshow locator-led status
Syntax Description Show running system information.show
Blink locator led on device.locator-led
Status.status
Cisco ACI Switch Command Reference, NX-OS Release 13.x224
S Commandsshow locator-led status
show logging ip access-list cacheshow logging ip access-list cache { permit | deny }
Syntax Description Show running system information.show
Logging information.logging
IP configuration.ip
Access-list.access-list
show entries in ACLLOG cache.cache
action is permit.permit
action is deny.deny
Cisco ACI Switch Command Reference, NX-OS Release 13.x 225
S Commandsshow logging ip access-list cache
show logging ip access-list drop-codesshow logging ip access-list drop-codes
Syntax Description Show running system information.show
Logging information.logging
IP configuration.ip
Access-list.access-list
Drop Codes.drop-codes
Cisco ACI Switch Command Reference, NX-OS Release 13.x226
S Commandsshow logging ip access-list drop-codes
show logging ip access-list spanshow logging ip access-list span
Syntax Description Show running system information.show
Logging information.logging
IP configuration.ip
Access-list.access-list
show entries in ACLLOG span.span
Cisco ACI Switch Command Reference, NX-OS Release 13.x 227
S Commandsshow logging ip access-list span
show mac address-table +showmac address-table [ { static | dynamic } ] [ {addressmac-addr} | {vlan id} | {interface interface-name}]+
Syntax Description Show running system information.show
Mac addr information.mac
MAC Address Table.address-table
Display Static Entries.static
Display Dynamic Entries.dynamic
address.address1
VLAN.vlan1
address.address
Interface.interface
VLAN.vlan
MAC Address. The type is ethernet.mac-addr
VLAN ID. The type is integer. The range is from 1 to 4095.id
Interface name. The type is interface.interface-name
Cisco ACI Switch Command Reference, NX-OS Release 13.x228
S Commandsshow mac address-table +
show macsec mka sessionshow macsec mka session [ details | { interface ethernet interface } ]
Syntax Description Show running system information.show
Show MACSEC information.macsec
Show MACSEC mka information.mka
Show MACSEC mka session information.session
Show MACSEC mka session details.details
Show MACSEC mka session information for interface.interface
Show MACSEC mka session information for ethernet interface.ethernet
Name of the Interface. The type is string.interface
Cisco ACI Switch Command Reference, NX-OS Release 13.x 229
S Commandsshow macsec mka session
show macsec mka statisticsshow macsec mka statistics [ interface ethernet interface ]
Syntax Description Show running system information.show
Show MACSEC information.macsec
Show MACSEC mka information.mka
Show MACSEC mka statistics information.statistics
Show MACSEC mka statistics information for interface.interface
Show MACSEC mka statistics information for ethernet interface.ethernet
Name of the Interface. The type is string.interface
Cisco ACI Switch Command Reference, NX-OS Release 13.x230
S Commandsshow macsec mka statistics
show macsec mka summaryshow macsec mka summary
Syntax Description Show running system information.show
Show MACSEC information.macsec
Show MACSEC mka information.mka
Show MACSEC mka summary information.summary
Show MACSEC mka session information.session
Show MACSEC mka session details.details
Show MACSEC mka session information for interface.interface
Show MACSEC mka session information for ethernet interface.ethernet
Name of the Interface. The type is string.interface
Cisco ACI Switch Command Reference, NX-OS Release 13.x 231
S Commandsshow macsec mka summary
show macsec secy statisticsshow macsec secy statistics [ interface ethernet interface ]
Syntax Description Show running system information.show
Show MACSEC information.macsec
Show MACSEC secy information.secy
Show MACSEC secy statistics information.statistics
Show MACSEC secy statistics information for interface.interface
Show MACSEC secy statistics information for ethernet interface.ethernet
Name of the Interface. The type is string.interface
Cisco ACI Switch Command Reference, NX-OS Release 13.x232
S Commandsshow macsec secy statistics
show moduleshow module [arg0]
Syntax Description Show Information.show
Module.module
please enter the module number. The type is integer. The range is from 1 to30.
arg0
Cisco ACI Switch Command Reference, NX-OS Release 13.x 233
S Commandsshow module
show module fexshow module fex {all | fexid}
Syntax Description Show running system information.show
Show module information.module
Show fex module information.fex
FEX number. The type is integer. The range is from 101 to 199.fexid
Show information for all FEX.all
Cisco ACI Switch Command Reference, NX-OS Release 13.x234
S Commandsshow module fex
show monitorshow monitor
Syntax Description Show running system information.show
Show SPAN information.monitor
Cisco ACI Switch Command Reference, NX-OS Release 13.x 235
S Commandsshow monitor
show monitor sessionshow monitor session { all | session_id | { range session_range } } [ brief | extended ]
Syntax Description Show running system information.show
Show SPAN information.monitor
Show session information.session
All sessions.all
Session Id 1-255. The type is integer. The range is from 1 to 255.session_id
Specify a range.range
session range(s): 1-4, 7, or 1-5,7-19. The type is integer_mrange. The rangeis from 1 to 255.
session_range
Brief information.brief
Session extended info like encaps, vlan filters per interfaces.extended
Cisco ACI Switch Command Reference, NX-OS Release 13.x236
S Commandsshow monitor session
show npv external-interface-usageshow npv external-interface-usage [ { server-interface arg0 } ]
Syntax Description Show running system information.show
Show Npv information.npv
Show external interface usage by server interfaces.external-interface-usage
Show external interface usage by a server interface.server-interface
Interface. The type is interface. The values are vfc, vfc-port-channel.arg0
Cisco ACI Switch Command Reference, NX-OS Release 13.x 237
S Commandsshow npv external-interface-usage
show npv flogi-tableshow npv flogi-table [ { vsan vsan-id } ]
Syntax Description Show running system information.show
Show Npv information.npv
Show information about FLOGI sessions.flogi-table
Show information about FLOGI sessions for a VSAN.vsan
Vsan-id. The type is integer_range. The range is from 1 to 4093.vsan-id
Cisco ACI Switch Command Reference, NX-OS Release 13.x238
S Commandsshow npv flogi-table
show npv flogi-table interfaceshow npv flogi-table interface arg0
Syntax Description Show running system information.show
Show Npv information.npv
Show information about FLOGI sessions.flogi-table
Show information about FLOGI sessions for a server interface.interface
Interface. The type is interface. The values are vfc, vfc-port-channel.arg0
Cisco ACI Switch Command Reference, NX-OS Release 13.x 239
S Commandsshow npv flogi-table interface
show npv statusshow npv status [ { vsan vsan-id } ]
Syntax Description Show running system information.show
Show Npv information.npv
Show Npv Status.status
Show NPV status for a specific VSAN.vsan
Vsan-id. The type is integer_range. The range is from 1 to 4093.vsan-id
Cisco ACI Switch Command Reference, NX-OS Release 13.x240
S Commandsshow npv status
show npv traffic-mapshow npv traffic-map [ { server-interface arg0 } ]
Syntax Description Show running system information.show
Show Npv information.npv
Show information about Traffic Map.traffic-map
Show information about Traffic map for a server interface.server-interface
Interface. The type is interface. The values are vfc, vfc-port-channel.arg0
Cisco ACI Switch Command Reference, NX-OS Release 13.x 241
S Commandsshow npv traffic-map
show ntp authentication-keysshow ntp authentication-keys
Syntax Description Show running system information.show
Show NTP information.ntp
Display authentication keys.authentication-keys
Cisco ACI Switch Command Reference, NX-OS Release 13.x242
S Commandsshow ntp authentication-keys
show ntp authentication-statusshow ntp authentication-status
Syntax Description Show running system information.show
Show NTP information.ntp
NTP Authentication Status.authentication-status
Cisco ACI Switch Command Reference, NX-OS Release 13.x 243
S Commandsshow ntp authentication-status
show ntp peer-statusshow ntp peer-status
Syntax Description Show running system information.show
Show NTP information.ntp
Show the status for all the server/peers.peer-status
Cisco ACI Switch Command Reference, NX-OS Release 13.x244
S Commandsshow ntp peer-status
show ntp peersshow ntp peers
Syntax Description Show running system information.show
Show NTP information.ntp
Show all the peers..peers
Cisco ACI Switch Command Reference, NX-OS Release 13.x 245
S Commandsshow ntp peers
show ntp statistics peer ipaddrshow ntp statistics peer ipaddr arg0
Syntax Description Show running system information.show
Show NTP information.ntp
Show the NTP statistics.statistics
Show the per-peer statistics counter of a peer..peer
Peer's IP address.ipaddr
The type is string. A.B.C.D.arg0
Cisco ACI Switch Command Reference, NX-OS Release 13.x246
S Commandsshow ntp statistics peer ipaddr
show ntp trusted-keysshow ntp trusted-keys
Syntax Description Show running system information.show
Show NTP information.ntp
Display trusted keys.trusted-keys
Cisco ACI Switch Command Reference, NX-OS Release 13.x 247
S Commandsshow ntp trusted-keys
show ospfv3 databaseshow ospfv3 [{vrf {vrf-name | all}}] database [[[[router | network | intra-area-prefix | {inter-area {irouter| iprefix}} | nssa-external | area-unknown | [[{link | link-unknown | grace} [interface]]]][{area area-id-ip}]]| {external [{tag tag_val}]} | as-unknown] [lsid] [self-originated | {adv-router advid} | {adv-router-nameadv-name} ]] [{vrf {vrf-name | all}}]
Syntax Description Show running system information.show
Display OSPFv3 status and configuration.ospfv3
Link-state Database Summary.database
Display router LSAs.router
Display network LSAs.network
Display Intra-Area-Prefix LSAs.intra-area-prefix
Display inter-area LSAs.inter-area
Display Inter-Area-Router LSAs.irouter
Display Inter-Area-Prefix LSAs.iprefix
Display type 7 (NSSA external) LSAs.nssa-external
Display area-scope unknown LSAs.area-unknown
Display Link LSAs.link
Display link-scope unknown LSAs.link-unknown
Display Grace LSAs.grace
The type is interface. Display only LSA's on this Interface.interface
Display only LSA's in this area.area
The type is ipaddr. Area Id as an integer or ip address.area-id-ip
Display type 5 (external) LSAs.external
Restrict display by tag.tag
The type is uinteger. 32-bit tag value.tag_val
Display as-scope unknown LSAs.as-unknown
The type is ipaddr. Restrict display by link state ID.lsid
Cisco ACI Switch Command Reference, NX-OS Release 13.x248
S Commandsshow ospfv3 database
Display only self-originated LSAs.self-originated
Restrict display by Advertising router.adv-router
The type is ipaddr. Advertising router ID.advid
Restrict display by Advertising router name.adv-router-name
The type is string. DNS Name of the Advertising router.adv-name
Display per-VRF information.vrf
The type is string. VRF name.vrf-name
Display information for all VRFs.all
Cisco ACI Switch Command Reference, NX-OS Release 13.x 249
S Commandsshow ospfv3 database
show ospfv3 database detailshow ospfv3 [{vrf {vrf-name | all}}] database [[[[router | network | intra-area-prefix | {inter-area {irouter| iprefix}} | nssa-external | area-unknown | [[{link | link-unknown | grace} [interface]]]][{area area-id-ip}]]| {external [{tag tag_val}]} | as-unknown] [lsid] [self-originated | {adv-router advid} | {adv-router-nameadv-name} ]] detail [{vrf {vrf-name | all}}]
Syntax Description Show running system information.show
Display OSPFv3 status and configuration.ospfv3
Link-state Database Summary.database
Display router LSAs.router
Display network LSAs.network
Display Intra-Area-Prefix LSAs.intra-area-prefix
Display inter-area LSAs.inter-area
Display Inter-Area-Router LSAs.irouter
Display Inter-Area-Prefix LSAs.iprefix
Display type 7 (NSSA external) LSAs.nssa-external
Display area-scope unknown LSAs.area-unknown
Display Link LSAs.link
Display link-scope unknown LSAs.link-unknown
Display Grace LSAs.grace
The type is interface. Display only LSA's on this Interface.interface
Display only LSA's in this area.area
The type is ipaddr. Area Id as an integer or ip address.area-id-ip
Display type 5 (external) LSAs.external
Restrict display by tag.tag
The type is uinteger. 32-bit tag value.tag_val
Display as-scope unknown LSAs.as-unknown
The type is ipaddr. Restrict display by link state ID.lsid
Cisco ACI Switch Command Reference, NX-OS Release 13.x250
S Commandsshow ospfv3 database detail
Display only self-originated LSAs.self-originated
Restrict display by Advertising router.adv-router
The type is ipaddr. Advertising router ID.advid
Restrict display by Advertising router name.adv-router-name
The type is string. DNS Name of the Advertising router.adv-name
Display LSA in detail.detail
Display per-VRF information.vrf
The type is string. VRF name.vrf-name
Display information for all VRFs.all
Cisco ACI Switch Command Reference, NX-OS Release 13.x 251
S Commandsshow ospfv3 database detail
show ospfv3 interfaceshow [ipv6] ospfv3 interface { arg0 | { [ brief ] vrf { all | vrf-name } } }
Syntax Description Show running system information.show
Display IPv6 information.ipv6
Display OSPFv3 status and configuration.ospfv3
OSPFv3 enabled interface.interface
Interface. The type is interface. The values are ethernet, port-channel, vlan,loopback.
arg0
Display summary of OSPFv3 interfaces.brief
Display per-VRF information.vrf
Display information for all VRFs.all
VRF name (Max Size 32). The type is string.vrf-name
Cisco ACI Switch Command Reference, NX-OS Release 13.x252
S Commandsshow ospfv3 interface
show ospfv3 neighborsshow [ipv6] ospfv3 neighbors { arg0 [ { ip [ detail ] } | detail | summary ] [vrf { all | vrf-name } ] } | { [ {ip [ detail ] } | detail | summary ] vrf { all | vrf-name } }
Syntax Description Show running system information.show
Display IPv6 information.ipv6
Display OSPFv3 status and configuration.ospfv3
Neighbor list.neighbors
Router ID of neighbor. The type is ipaddr.ip
Show detailed neighbor display.detail
Interface. The type is interface. The values are ethernet, port-channel, vlan,loopback.
arg0
Summary of neighbors.summary
Display per-VRF information.vrf
Display information for all VRFs.all
VRF name (Max Size 32). The type is string.vrf-name
Cisco ACI Switch Command Reference, NX-OS Release 13.x 253
S Commandsshow ospfv3 neighbors
show ospfv3 route vrfshow [ipv6] ospfv3 route [ summary | { ipv6-prefix [ longer-prefixes ] [ summary ] } | ipv6-addr ] vrf {all | vrf-name }
Syntax Description Show running system information.show
Display IPv6 information.ipv6
Display OSPFv3 status and configuration.ospfv3
Internal OSPFv3 routes.route
Show single OSPFv3 route. The type is ipv6.ipv6-addr
Show single exact match OSPFv3 route. The type is ipv6_prefix.ipv6-prefix
Show route counts.summary
Show exact match and more specific routes.longer-prefixes
Display per-VRF information.vrf
Display information for all VRFs.all
VRF name (Max Size 32). The type is string.vrf-name
Cisco ACI Switch Command Reference, NX-OS Release 13.x254
S Commandsshow ospfv3 route vrf
show ospfv3 summary-address vrfshow [ipv6] ospfv3 summary-address vrf { all | vrf-name }
Syntax Description Show running system information.show
Display IPv6 information.ipv6
Display OSPFv3 status and configuration.ospfv3
Summary-address redistribution information.summary-address
Display per-VRF information.vrf
Display information for all VRFs.all
VRF name (Max Size 32). The type is string.vrf-name
Cisco ACI Switch Command Reference, NX-OS Release 13.x 255
S Commandsshow ospfv3 summary-address vrf
show ospfv3 trafficshow [ipv6] ospfv3 traffic { arg0 | { vrf { all | vrf-name } } }
Syntax Description Show running system information.show
Display IPv6 information.ipv6
Display OSPFv3 status and configuration.ospfv3
Packet counters.traffic
Interface. The type is interface. The values are ethernet, port-channel, vlan,loopback.
arg0
Display per-VRF information.vrf
Display information for all VRFs.all
VRF name (Max Size 32). The type is string.vrf-name
Cisco ACI Switch Command Reference, NX-OS Release 13.x256
S Commandsshow ospfv3 traffic
show ospfv3 vrfshow [ipv6] ospfv3 vrf { all | vrf-name }
Syntax Description Show running system information.show
Display IPv6 information.ipv6
Display OSPFv3 status and configuration.ospfv3
Display per-VRF information.vrf
Display information for all VRFs.all
VRF name (Max Size 32). The type is string.vrf-name
Cisco ACI Switch Command Reference, NX-OS Release 13.x 257
S Commandsshow ospfv3 vrf
show port-channel capacityshow port-channel capacity
Syntax Description Show running system information.show
Show port-channel information.port-channel
Capacity information.capacity
Cisco ACI Switch Command Reference, NX-OS Release 13.x258
S Commandsshow port-channel capacity
show port-channel databaseshow port-channel database [ { interface if0 } ]
Syntax Description Show running system information.show
Show port-channel information.port-channel
Show port-channel database.database
Specify a port-channel.interface
. The type is interface_mrange. The values are port-channel.if0
Cisco ACI Switch Command Reference, NX-OS Release 13.x 259
S Commandsshow port-channel database
show port-channel extendedshow port-channel extended [ { interface if0 } ]
Syntax Description Show running system information.show
Show port-channel information.port-channel
Show port-channel extended.extended
Specify a port-channel.interface
. The type is interface. The values are port-channel.if0
Cisco ACI Switch Command Reference, NX-OS Release 13.x260
S Commandsshow port-channel extended
show port-channel summaryshow port-channel summary [ { interface if0 } ]
Syntax Description Show running system information.show
Show port-channel information.port-channel
Show port-channel summary.summary
Specify a port-channel.interface
. The type is interface. The values are port-channel.if0
Cisco ACI Switch Command Reference, NX-OS Release 13.x 261
S Commandsshow port-channel summary
show port-channel trafficshow port-channel traffic [ { interface if0 } ]
Syntax Description Show running system information.show
Show port-channel information.port-channel
Show port-channel traffic statistics.traffic
Specify a port-channel.interface
. The type is interface. The values are port-channel.if0
Cisco ACI Switch Command Reference, NX-OS Release 13.x262
S Commandsshow port-channel traffic
show port-channel usageshow port-channel usage
Syntax Description Show running system information.show
Show port-channel information.port-channel
Show port-channel number usage.usage
Cisco ACI Switch Command Reference, NX-OS Release 13.x 263
S Commandsshow port-channel usage
show porttrackshow porttrack
Syntax Description Show running system information.show
Port Tracking.porttrack
Cisco ACI Switch Command Reference, NX-OS Release 13.x264
S Commandsshow porttrack
show processesshow processes
Syntax Description Show running system information.show
Show processes.processes
Cisco ACI Switch Command Reference, NX-OS Release 13.x 265
S Commandsshow processes
show processes cpushow processes cpu
Syntax Description Show running system information.show
Show processes.processes
Show processes CPU Info.cpu
Cisco ACI Switch Command Reference, NX-OS Release 13.x266
S Commandsshow processes cpu
show processes cpu sortshow processes cpu sort
Syntax Description Show running system information.show
Show processes.processes
Show processes CPU Info.cpu
Show processes CPU Info (Sorted by Cpu Util).sort
Cisco ACI Switch Command Reference, NX-OS Release 13.x 267
S Commandsshow processes cpu sort
show processes memoryshow processes memory
Syntax Description Show running system information.show
Show processes.processes
Show processes Memory Info.memory
Cisco ACI Switch Command Reference, NX-OS Release 13.x268
S Commandsshow processes memory
show ptp briefshow ptp brief
Syntax Description Show running system information.show
Precision Time Protocol (IEEE 1588) Subsystem.ptp
PTP port states in brief.brief
Read Only.__readonly__
ptp table.TABLE_ptp
The type is string. ptp ifindex.ptp-ifindex
The type is string. ptp bmc state.state
The type is string. End of table.ptp-end
Cisco ACI Switch Command Reference, NX-OS Release 13.x 269
S Commandsshow ptp brief
show ptp clockshow ptp clock
Syntax Description Show running system information.show
Precision Time Protocol (IEEE 1588) Subsystem.ptp
PTP local clock.clock
Read Only.__readonly__
The type is integer. Domain Id.domain-id
The type is string. Clock Id.clock-id
The type is integer. Priority2.priority1
The type is integer. Priority2.priority2
The type is integer. Number of PTP ports.num-ports
The type is integer. Class.class
The type is integer. Clock accuracy.accuracy
The type is integer. scaled log variance.scaled-log-variance
The type is integer. Offset from master.offset-from-master
The type is integer. Mean path delay to master.mean-path-delay-to-master
The type is integer. Steps removed.steps-removed
Cisco ACI Switch Command Reference, NX-OS Release 13.x270
S Commandsshow ptp clock
show ptp clock foreign-masters recordshow ptp clock foreign-masters record [ { interface if0 } ]
Syntax Description Show running system information.show
Precision Time Protocol (IEEE 1588) Subsystem.ptp
PTP clock.clock
foreign-masters.foreign-masters
record.record
Specify interface.interface
The type is interface. . The values are ethernet.if0
Read Only.__readonly__
ptp table.TABLE_ptp
The type is string. Interface name.interface-name
The type is string. Clock Id.clock-id
The type is integer. Priority2.priority1
The type is integer. Priority2.priority2
The type is integer. Class.class
The type is integer. Clock accuracy.accuracy
The type is integer. scaled log variance.scaled-log-variance
The type is integer. Steps removed.steps-removed
The type is integer. Is Grandmaster.is-gm
The type is string. End of table.ptp-end
Cisco ACI Switch Command Reference, NX-OS Release 13.x 271
S Commandsshow ptp clock foreign-masters record
show ptp correctionsshow ptp corrections
Syntax Description Show running system information.show
Precision Time Protocol (IEEE 1588) Subsystem.ptp
Read Only.__readonly__
Display last few corrections.corrections
ptp table.TABLE_ptp
The type is string. interface name.intf-name
The type is string. sup time.sup-time
The type is integer. correction value.correction-val
The type is integer. mean path delay.mean-path-delay
The type is string. End of table.ptp-end
Cisco ACI Switch Command Reference, NX-OS Release 13.x272
S Commandsshow ptp corrections
show ptp countersshow ptp counters { {interface if0} | all }
Syntax Description Show running system information.show
Precision Time Protocol (IEEE 1588) Subsystem.ptp
Read Only.__readonly__
Display PTP packet counters.counters
Enter the port interface.interface
Displays all information.all
The type is interface. . The values are ethernet.if0
ptp table.TABLE_ptp
The type is string. interface name.interface_name
The type is integer. No. of TX Announce Packets.tx-announce-pkts
The type is integer. No. of TX Sync Packets.tx-sync-pkts
The type is integer. No. of TX Follow-up Packets.tx-follow-up-pkts
The type is integer. No. of TX Delay Request Packets.tx-delay-req-pkts
The type is integer. No. of TX Delay Response Packets.tx-delay-resp-pkts
The type is integer. No. of TX PDelay Request Packets.tx-pdelay-req-pkts
The type is integer. No. of TX PDelay Response Packets.tx-pdelay-resp-pkts
The type is integer. No. of TX PDelay Follow-up Packets.tx-pdelay-follow-up-pkts
The type is integer. No. of TX PTP management Packets.tx-mgmt-pkts
The type is integer. No. of RX Announce Packets.rx-announce-pkts
The type is integer. No. of RX Sync Packets.rx-sync-pkts
The type is integer. No. of RX Follow-up Packets.rx-follow-up-pkts
The type is integer. No. of RX Delay Request Packets.rx-delay-req-pkts
The type is integer. No. of RX Delay Response Packets.rx-delay-resp-pkts
Cisco ACI Switch Command Reference, NX-OS Release 13.x 273
S Commandsshow ptp counters
The type is integer. No. of RX PDelay Request Packets.rx-pdelay-req-pkts
The type is integer. No. of RX PDelay Response Packets.rx-pdelay-resp-pkts
The type is integer. No. of RX PDelay Follow-up Packets.rx-pdelay-follow-up-pkts
The type is integer. No. of RX PTP management Packets.rx-mgmt-pkts
The type is string. End of table.ptp-end
Cisco ACI Switch Command Reference, NX-OS Release 13.x274
S Commandsshow ptp counters
show ptp parentshow ptp parent
Syntax Description Show running system information.show
Precision Time Protocol (IEEE 1588) Subsystem.ptp
PTP parent clock.parent
Read Only.__readonly__
The type is string. Clock Id.clock-id
The type is integer. Port number.port-num
The type is string. observed parent offset.obs-parent-offset
The type is string. observed parent clock phase change.obs-parent-clk-phase-chg
The type is string. Grandmaster Id.gm-id
The type is integer. Grandmaster class.gm-class
The type is integer. Clock accuracy.gm-accuracy
The type is integer. scaled log variance.gm-scaled-log-variance
The type is integer. GM Priority1.gm-priority1
The type is integer. GM Priority2.gm-priority2
Cisco ACI Switch Command Reference, NX-OS Release 13.x 275
S Commandsshow ptp parent
show publickeyshow publickey
Syntax Description Show public key from certificate.show
public key information.publickey
Cisco ACI Switch Command Reference, NX-OS Release 13.x276
S Commandsshow publickey
show radius-servershow radius-server [sorted | {groups [grp-name]}]
Syntax Description Show Information.show
Radius-server.radius-server
Sorted server list.sorted
Radius server groups.groups
Group Name. The type is string.grp-name
Cisco ACI Switch Command Reference, NX-OS Release 13.x 277
S Commandsshow radius-server
show redundancy statusshow redundancy status
Syntax Description Show running system information.show
Show system redundancy status.redundancy
Current redundancy status.status
Cisco ACI Switch Command Reference, NX-OS Release 13.x278
S Commandsshow redundancy status
show route-mapshow route-map [ strarg ]
Syntax Description Show running system information.show
Route-map information.route-map
Route-map name (Max Size 100). The type is string.strarg
Cisco ACI Switch Command Reference, NX-OS Release 13.x 279
S Commandsshow route-map
show san-port-channel databaseshow san-port-channel database
Syntax Description Show running system information.show
Show san-port-channel information.san-port-channel
Show san-port-channel database.database
Cisco ACI Switch Command Reference, NX-OS Release 13.x280
S Commandsshow san-port-channel database
show san-port-channel summaryshow san-port-channel summary
Syntax Description Show running system information.show
Show san-port-channel information.san-port-channel
Show san-port-channel summary.summary
Cisco ACI Switch Command Reference, NX-OS Release 13.x 281
S Commandsshow san-port-channel summary
show san-port-channel usageshow san-port-channel usage
Syntax Description Show running system information.show
Show san-port-channel information.san-port-channel
Show san-port-channel usage.usage
Cisco ACI Switch Command Reference, NX-OS Release 13.x282
S Commandsshow san-port-channel usage
show service copy infoshow service copy info [ { group [ gid ] } | { destination [ { ip dip | dipv6 } { vnid dvnid | dvnidhex } ] } ]
Syntax Description Show running system information.show
Display service information.service
Display service copy information.copy
Display service copy information.info
Display group information.group
Display destination information.destination
ip address of destination.ip
ipv6 address of destination.ipv6
vnid address of destination.vnid
group number. The type is integer. The range is from 0 to 65535.gid
The type is ipaddr. IP address.dip
The type is ipv6. IPv6 address.dipv6
vnid number. The type is integer.dvnid
vnid number. The type is hex.dvnidhex
Cisco ACI Switch Command Reference, NX-OS Release 13.x 283
S Commandsshow service copy info
show service redir infoshow service redir info [ { group [ gid ] } | { destination [ { ip dip | dipv6 } { vnid dvnid | dvnidhex } ] } ]
Syntax Description Show running system information.show
Display service information.service
Display service redirect information.redir
Display service redirect information.info
Display group information.group
Display destination information.destination
ip address of destination.ip
vnid address of destination.vnid
group number. The type is integer. The range is from 0 to 65535.gid
The type is ipaddr. IP address.dip
The type is ipv6. IPv6 address.dipv6
vnid number. The type is hex.dvnidhex
vnid number. The type is integer.dvnid
Cisco ACI Switch Command Reference, NX-OS Release 13.x284
S Commandsshow service redir info
show snmpshow snmp
Syntax Description Show running system information.show
Display SNMP information.snmp
Cisco ACI Switch Command Reference, NX-OS Release 13.x 285
S Commandsshow snmp
show snmp communityshow snmp community
Syntax Description Show running system information.show
Display SNMP information.snmp
Display SNMP Community information.community
Cisco ACI Switch Command Reference, NX-OS Release 13.x286
S Commandsshow snmp community
show snmp contextshow snmp context
Syntax Description Show running system information.show
Display SNMP information.snmp
Display SNMP Context information.context
Cisco ACI Switch Command Reference, NX-OS Release 13.x 287
S Commandsshow snmp context
show snmp engineIDshow snmp engineID
Syntax Description Show running system information.show
Display SNMP information.snmp
Show snmp engineID.engineID
Cisco ACI Switch Command Reference, NX-OS Release 13.x288
S Commandsshow snmp engineID
show snmp hostshow snmp host
Syntax Description Show commands.show
Show snmp internal information.snmp
show snmp hosts.host
Cisco ACI Switch Command Reference, NX-OS Release 13.x 289
S Commandsshow snmp host
show snmp summaryshow snmp summary
Syntax Description Show running system information.show
Display SNMP information.snmp
Display SNMP Summary.summary
Cisco ACI Switch Command Reference, NX-OS Release 13.x290
S Commandsshow snmp summary
show snmp usershow snmp user
Syntax Description Show running system information.show
Display SNMP information.snmp
Display SNMP User information.user
Cisco ACI Switch Command Reference, NX-OS Release 13.x 291
S Commandsshow snmp user
show spromshow sprom { backplane | { module arg1 } | { fan arg0 } | { powersupply arg2 } | sup | stby-sup | all }
Syntax Description Show running system information.show
Show SPROM contents.sprom
show all sproms contents.all
show powersupply sprom contents.powersupply
show linecard module sprom contents.module
show fan module sprom contents.fan
show stanby supervisor sprom contents.stby-sup
show supervisor sprom contents.sup
show backplane clock module sprom contents.backplane
please enter the fan number. The type is integer. The range is from 1 to 15.arg0
please enter the module number. The type is integer. The range is from 1 to30.
arg1
please enter the powersupply number. The type is integer. The range is from1 to 10.
arg2
Cisco ACI Switch Command Reference, NX-OS Release 13.x292
S Commandsshow sprom
show switchnameshow switchname
Syntax Description Show running system information.show
Show the system's hostname.switchname
Cisco ACI Switch Command Reference, NX-OS Release 13.x 293
S Commandsshow switchname
show system error-idshow system error-id { list | i0 }
Syntax Description Show running system information.show
System-related show commands.system
Show description about errors.error-id
Show description about all error IDs.list
The type is hex. Show description about specific error. The range is from 0x0 to0xffffffff.
i0
Cisco ACI Switch Command Reference, NX-OS Release 13.x294
S Commandsshow system error-id
show system modeshow system mode
Syntax Description Show running system information.show
System-related commands.system
Show system mode.mode
Cisco ACI Switch Command Reference, NX-OS Release 13.x 295
S Commandsshow system mode
show system redundancy statusshow system redundancy [ ha ] status
Syntax Description Show running system information.show
System-related show commands.system
Show system redundancy status.redundancy
Current redundancy status.status
Vdc redundancy status.ha
Cisco ACI Switch Command Reference, NX-OS Release 13.x296
S Commandsshow system redundancy status
show system reset-reasonshow system reset-reason [ { module arg0 } ]
Syntax Description Show running system information.show
System-related show commands.system
Show last reset reason.reset-reason
Module.module
please enter the module number. The type is integer. The range is from 1to 30.
arg0
Cisco ACI Switch Command Reference, NX-OS Release 13.x 297
S Commandsshow system reset-reason
show system reset-reason fexshow system reset-reason fex fexid
Syntax Description Show running system information.show
System-related show commands.system
Show last reset reason.reset-reason
Show fex last reset reason.fex
FEX number. The type is integer. The range is from 101 to 199.fexid
Cisco ACI Switch Command Reference, NX-OS Release 13.x298
S Commandsshow system reset-reason fex
show system resourcesshow system resources
Syntax Description Show running system information.show
System-related show commands.system
Show system resources.resources
Cisco ACI Switch Command Reference, NX-OS Release 13.x 299
S Commandsshow system resources
show system uptimeshow system uptime
Syntax Description Show running system information.show
System information.system
How long the system has been up.uptime
Cisco ACI Switch Command Reference, NX-OS Release 13.x300
S Commandsshow system uptime
show tacacs-servershow tacacs-server [sorted | {groups [grp-name]}]
Syntax Description Show Information.show
Tacacs-server.tacacs-server
Sorted server list.sorted
Tacacs server groups.groups
Group Name. The type is string.grp-name
Cisco ACI Switch Command Reference, NX-OS Release 13.x 301
S Commandsshow tacacs-server
show tech-support analytics briefshow tech-support analytics brief
Syntax Description Show running system information.show
Gather information for trouble shooting.tech-support
Show Policyelem tech-support information.analytics
Brief information.brief
Cisco ACI Switch Command Reference, NX-OS Release 13.x302
S Commandsshow tech-support analytics brief
show usersshow users
Syntax Description Show running system information.show
Show users logged onto the system and their sessions.users
Cisco ACI Switch Command Reference, NX-OS Release 13.x 303
S Commandsshow users
show versionshow version
Syntax Description Show running system information.show
Show running firmware version and basic system information.version
Cisco ACI Switch Command Reference, NX-OS Release 13.x304
S Commandsshow version
show version moduleshow version module [arg0]
Syntax Description Show running system information.show
Show the software version.version
Module.module
please enter the module number. The type is integer. The range is from 1 to30.
arg0
Cisco ACI Switch Command Reference, NX-OS Release 13.x 305
S Commandsshow version module
show vlanshow vlan [extended]
Syntax Description Show running system information.show
VLAN status.vlan
VLAN extended info like encaps.extended
Cisco ACI Switch Command Reference, NX-OS Release 13.x306
S Commandsshow vlan
show vlan all-portsshow vlan all-ports
Syntax Description Show running system information.show
VLAN status.vlan
Show all ports on VLAN.all-ports
Cisco ACI Switch Command Reference, NX-OS Release 13.x 307
S Commandsshow vlan all-ports
show vlan briefshow vlan brief
Syntax Description Show running system information.show
VLAN status.vlan
All VLAN status in brief.brief
Cisco ACI Switch Command Reference, NX-OS Release 13.x308
S Commandsshow vlan brief
show vlan fcoeshow vlan fcoe [ vlan-id ]
Syntax Description Show running system information.show
VLAN status.vlan
FCOE Configuration.fcoe
VLAN ID 1-3967 or range(s): 1-5, 10 or 2-5,7-19. The type is integer_mrange.The range is from 1 to 4095.
vlan-id
Cisco ACI Switch Command Reference, NX-OS Release 13.x 309
S Commandsshow vlan fcoe
show vlan idshow vlan id vlan-id [extended]
Syntax Description Show running system information.show
VLAN status.vlan
VLAN status by VLAN id.id
VLAN ID 1-3967 or range(s): 1-5, 10 or 2-5,7-19. The type is integer_mrange.The range is from 1 to 4095.
vlan-id
VLAN extended info like encaps.extended
Cisco ACI Switch Command Reference, NX-OS Release 13.x310
S Commandsshow vlan id
show vlan reservedshow vlan reserved [extended]
Syntax Description Show running system information.show
VLAN status.vlan
reserved
VLAN extended info like encaps.extended
Cisco ACI Switch Command Reference, NX-OS Release 13.x 311
S Commandsshow vlan reserved
show vlan summaryshow vlan summary
Syntax Description Show running system information.show
VLAN status.vlan
VLAN summary information.summary
Cisco ACI Switch Command Reference, NX-OS Release 13.x312
S Commandsshow vlan summary
show vpcshow vpc [ { vpc-number | { brief [ { vpc vpc-number } ] } | { extended [ { vpc vpc-number } ] } } ]
Syntax Description Show running system information.show
Virtual Port Channel configuration.vpc
Brief display of vPC status.brief
Extended display of vPC status.extended
Enter a Virtual Port Channel number. The type is integer. to 4096. The rangeis from 1
vpc-number
Cisco ACI Switch Command Reference, NX-OS Release 13.x 313
S Commandsshow vpc
show vpc consistency-parametersshow vpc consistency-parameters { global | { interface if } | { vpc vpc-num } }
Syntax Description Show running system information.show
Virtual Port Channel configuration.vpc
Show vPC Consistency Parameters.consistency-parameters
Global Parameters.global
Specify interface.interface
. The type is interface. The values are port-channel.if
Enter a Virtual Port Channel number. The type is integer. to 4096. Therange is from 1
vpc-num
Cisco ACI Switch Command Reference, NX-OS Release 13.x314
S Commandsshow vpc consistency-parameters
show vpc orphan-portsshow vpc orphan-ports
Syntax Description Show running system information.show
Virtual Port Channel configuration.vpc
Show vPC orphan ports.orphan-ports
Cisco ACI Switch Command Reference, NX-OS Release 13.x 315
S Commandsshow vpc orphan-ports
show vpc peer-keepaliveshow vpc peer-keepalive
Syntax Description Show running system information.show
Virtual Port Channel configuration.vpc
vPC keepalive status.peer-keepalive
Cisco ACI Switch Command Reference, NX-OS Release 13.x316
S Commandsshow vpc peer-keepalive
show vpc roleshow vpc role
Syntax Description Show running system information.show
Virtual Port Channel configuration.vpc
vPC role status.role
Cisco ACI Switch Command Reference, NX-OS Release 13.x 317
S Commandsshow vpc role
show vpc statistics peer-keepaliveshow vpc statistics peer-keepalive
Syntax Description Show running system information.show
Virtual Port Channel configuration.vpc
Statistics.statistics
peer keepalive module related statistics.peer-keepalive
Cisco ACI Switch Command Reference, NX-OS Release 13.x318
S Commandsshow vpc statistics peer-keepalive
show vpc statistics vpcshow vpc statistics vpc vpc_num
Syntax Description Show running system information.show
Virtual Port Channel configuration.vpc
Statistics.statistics
Enter a Virtual Port Channel number. The type is integer. to 4096. The rangeis from 1
vpc_num
Cisco ACI Switch Command Reference, NX-OS Release 13.x 319
S Commandsshow vpc statistics vpc
show vrfshow vrf [vrf-name | all] [detail [extended]] [{order id}]
Syntax Description Show running system information.show
Display VRF information.vrf
VRF name. The type is vrf_name.vrf-name
Display VRF information for all VRFs.all
Specify ordering.order
Order by ID.id
Display VRF detail information.detail
Display extended VRF information.extended
Cisco ACI Switch Command Reference, NX-OS Release 13.x320
S Commandsshow vrf
show vrf interfaceshow vrf [vrf-name | all ] interface [interface]
Syntax Description Show running system information.show
Display VRF information.vrf
VRF name. The type is vrf_name.vrf-name
Display VRF information for all VRFs.all
Display interface VRF information.interface
Display interface VRF information. The type is interface.interface
Cisco ACI Switch Command Reference, NX-OS Release 13.x 321
S Commandsshow vrf interface
show vsanshow vsan [ vsan-id ]
Syntax Description Show running system information.show
Show vsan information.vsan
VSAN is range <1-4078>. The type is integer_range. The range is from 1 to4078.
vsan-id
Cisco ACI Switch Command Reference, NX-OS Release 13.x322
S Commandsshow vsan
show vsan membershipshow vsan [ vsan-id ] membership
Syntax Description Show running system information.show
Show vsan information.vsan
Show membership information.membership
VSAN is range <1-4078>. The type is integer_range. The range is from 1to 4078.
vsan-id
Cisco ACI Switch Command Reference, NX-OS Release 13.x 323
S Commandsshow vsan membership
show vsan membership interfaceshow vsan membership interface { arg0 }
Syntax Description Show running system information.show
Show vsan information.vsan
Show membership information.membership
Show membership information for interface(s).interface
Interface. The type is interface. The values are vfc, vfc-port-channel.arg0
Cisco ACI Switch Command Reference, NX-OS Release 13.x324
S Commandsshow vsan membership interface
show vsan usageshow vsan usage
Syntax Description Show running system information.show
Show vsan information.vsan
Show vsan usage in the system.usage
Cisco ACI Switch Command Reference, NX-OS Release 13.x 325
S Commandsshow vsan usage
show zoning-filtershow zoning-filter [ { filter id } ]
Syntax Description Show running system information.show
Display Zoning-Filter information.zoning-filter
Display Zoning-Filter information using this Filter.filter
Filter ID/string. The type is string.id
Cisco ACI Switch Command Reference, NX-OS Release 13.x326
S Commandsshow zoning-filter
show zoning-rule +show zoning-rule [ { src-epg epg0 } | { dst-epg epg1 } | { scope scopeId } | { filter filt } ]+
Syntax Description Show running system information.show
Display Zoning-Rule information.zoning-rule
Display Source EPG information.src-epg
Source EPG number. The type is integer. The range is from 0 to 65535.epg0
Display Destination EPG information.dst-epg
Destination EPG number. The type is integer. The range is from 0 to 65535.epg1
Display Rules for this Scope.scope
Scope ID. The type is integer. The range is from 1 to 16777215.scopeId
Display Rules using this Filter.filter
Filter ID/string. The type is string.filt
Cisco ACI Switch Command Reference, NX-OS Release 13.x 327
S Commandsshow zoning-rule +
Cisco ACI Switch Command Reference, NX-OS Release 13.x328
S Commandsshow zoning-rule +
T Commands
• techsupport local, page 330
Cisco ACI Switch Command Reference, NX-OS Release 13.x 329
techsupport localtechsupport local
Syntax Description Tech Support collection.techsupport
collect techsupport for this node.local
Cisco ACI Switch Command Reference, NX-OS Release 13.x330
T Commandstechsupport local
Configuring Switch Management
• Configuring Switch Console Settings, page 332
Cisco ACI Switch Command Reference, NX-OS Release 13.x 331
Configuring Switch Console SettingsIn the switch command line interface, use the console_speed_setup.sh command to locally configure theconsole settings.
When you configure the settings from the console, the new settings take effect immediately. When youconfigure the settings from an SSH session, the new settings take effect upon the next switch reboot.
Note
The following example shows the use of the command. To change a setting, type y and follow the prompts.To view the settings without making changes, type n to every question.
Leaf-1# console_speed_setup.sh
Configure the Baud rate? (yes/no) [y]: nConfigure the Databits? (yes/no) [y]: nConfigure the Parity? (yes/no) [y]: nConfigure the Stop bits? (yes/no) [y]: n
databits_val 3stopbits_val 0parity_val 0These are the new settingsSerial parameters become effective immediately on serial consoleFor SSH session, the serial parameters will take effect on the next reboot/isan/utils/cmosio -w console 12.3/bin/stty 115200 cs8 -cstopb
Would you like to proceed? (yes/no) [n]: nLeaf-1#
For the default console settings, including the initial baud rate, refer to the Hardware Installation Guide forthe switch model.
Cisco ACI Switch Command Reference, NX-OS Release 13.x332
Configuring Switch ManagementConfiguring Switch Console Settings
Using Boot Loader Commands
• Using Boot Loader Commands, page 333
• boot (loader command), page 334
• cmdline (loader command), page 335
• set gw (loader command), page 336
• set ip (loader command), page 337
Using Boot Loader CommandsWhen the switch starts up in the boot loader mode, a set of commands is available to set kernel kickstartparameters that may be required during advanced troubleshooting and recovery options. These commandsare not used in normal operation.
Cisco ACI Switch Command Reference, NX-OS Release 13.x 333
boot (loader command)boot protocol://location
Syntax Description Only tftp is supported.protocol
The server address or hostname and path to the imagefile to be booted.
location
Usage Guidelines Use this command to download and boot from an image file on a remote TFTP server.
Examples This example causes the switch to download and boot from the specified image file on the remote server.
loader> boot tftp://192.2.0.123/images/bootimage1
Cisco ACI Switch Command Reference, NX-OS Release 13.x334
Using Boot Loader Commandsboot (loader command)
cmdline (loader command)cmdline [clear_config] [clear_log] [init_system] [no_hap_reset]
Syntax Description Clears all configuration databases and causes a stateless reload. This option isuseful when upgrading the switch from an old and incompatible software image,such as a pre-release image.
clear_config
Completely clears all core files and logs within the switch. This option is usefulwhen the switch fails to boot due to full partitions.
clear_log
Securely erases and repartitions the disk.init_system
Prevents a switch from continuously reloading due to a process failure. With thisoption, the switch will not reload after a failure, but will stop with a login promptto allow troubleshooting.
no_hap_reset
Usage Guidelines One or more options can be appended to the base cmdline command, but the entire command must be enteredon a single line.
Examples This example shows the command with one option:
Aborting config file read and autobootNo autoboot or failed autoboot. falling to loader
Loader Version 7.17
loader > cmdline no_hap_resetloader >
This example shows the command with two options:
loader > cmdline init_system clear_configloader >
Cisco ACI Switch Command Reference, NX-OS Release 13.x 335
Using Boot Loader Commandscmdline (loader command)
set gw (loader command)set gw ipaddress
Syntax Description The gateway IP address for the switch.ipaddress
Usage Guidelines Use this command to configure the gateway IP address for the switch.
Examplesloader> set gw 192.2.0.1
Cisco ACI Switch Command Reference, NX-OS Release 13.x336
Using Boot Loader Commandsset gw (loader command)
set ip (loader command)set ip ipaddress mask
Syntax Description The management IP address to be assigned to the switch.ipaddress
The subnet mask of the management IP address.mask
Usage Guidelines Use this command to configure the initial management IP address for the switch.
Examplesloader> set ip 192.2.0.123 255.255.255.0
Cisco ACI Switch Command Reference, NX-OS Release 13.x 337
Using Boot Loader Commandsset ip (loader command)
Cisco ACI Switch Command Reference, NX-OS Release 13.x338
Using Boot Loader Commandsset ip (loader command)