SINCE1958

MCX SERIESChoke Va lves

P r e c i s e .

Q u a l i t y .

R e l i a b l e .

CELEBRATING

1958 - 2018

www.taylorvalve.com

Full Open Throttling Full Closed

When the front disc is rotated,changing the alignment andrelationship to the fixed back disc,the flow area and orifice size areaffected, the result is either increase or decrease in flow.

When the holeson both discs arealigned the valve isin the Full Open Position.

When the front discis rotated a full 90o

(one quarter turn),the valve is in theFull Closed Position.

Taylor Valve Technology Multi-Orifice Valve Design Principle Provides Precision Control. The two adjacent internal discs each contain two precision orifices.

The discs are lapped to within two light bands of flatness (+/- .00002”) to achieve positive shut off and maintain precise control. The fixed back disc is held perpendicular to the flow. The front disc floats against the back disc and seeks a mating surface promoting a positive seal. The differential pressure across the upstream disc and the downsteam disc stabilizes the control surfaces. Vibration, noise or fatigues normally associated with loose or unsupported parts are eliminated. No control surfaces are introduced into the orifice, providing a clear center line for the flow. The valves are rated for shut-off at ANSI Class III or IV depending on the style of valve and trim used. The orifices of the standard disc expose a small control surface profile to the fluid steam reducing wear. The multi-orifice design produces near linear flow characteristics. The low torque and quarter-turn design of Taylor Valve Technology’s Multi-orifice valves allows for a variety of actuation options: manual, pneumatic, hydraulic, or electric.

MOV Valve Principle of Operation

2

www.taylorvalve.com

FLOW

End-to-End

461 3

7

9

5 2 8

1 Body 12 Rotator 13 Disc 24 O-Ring 45 O Ring 16 Dowel Pin 47 Handle 18 Spiral Retaining Ring 19 Retaining Ring 4**10* Wear Sleeve 1

Description QtyNo.

The information contained in these drawings is the sole property of Taylor Valve Technology Inc. and any reproduction in part or whole without the written permission of Taylor Valve Technology Inc. is prohibited.

CONNECTIONMCX CHOKE STANDARD DIMENSIONS (IN. +/- .10)

FNPTBUTT-WELD150 # RFF150 # RTJ300 # RFF300 # RTJ600 # RFF600 # RTJ900 # RFF900 # RTJ

1500 # RFF1500 # RTJ2500 # RFF2500 # RTJ

12.50-

13.2513.2513.2513.2513.2513.2513.2513.2513.2513.25

--

9.00-

9.009.009.509.509.509.509.509.509.509.50

--

--

15.0715.0715.0715.0715.0715.07

------

SIZE3” 4” 6”

MCX Inline Choke3” & 4” Configurations1018/1020 CS, 316 SS)¼ Turn ActuatedBody Rating = 3,000 PSICV Range = 11.2 – 279.83

*Not available in threaded configuration** Not shown in section view

NOTE: Taylor Valve reserves the right to change product designs and specifications without notice.

MCX Specifications and Cutaway View

3

WWW.TAYLORVALVE.COM

MCX SERIESCHOKE VALVES

BenefitsFEATURES

Applications: • Water Injection Control Valve• Gas Lift Injection Control• Throttling Valve• High DP Valve• Motor Operated Valve• Enhanced Oil Recovery

Accurate Control - Superior design is unequalled for throttling control and accuracy. Unique sealing and fluid flow dynamics permit compliance with current environmental requirements.

Extended Mean Time Between Service - Robust design and liberal application of hardened materials, efficient flow-geometry means the valves offer maximum production potential and minimum service requirements.

Easy Maintenance - Choke valves are designed to provide simple straightforward disassembly with no special tooling or fixtures.

Optional Features - Choke valves can have trims and actuators custom designed for specific requirements, such as, special trims for noise reduction and sand control, several trims are available to accommodate high pressure flows or minimum pressure loss applications.

4

MC

X

The information contained in these drawings is the sole property of Taylor Valve Technology Inc. and any reproduction in part or whole without the written permission of Taylor Valve Technology Inc. is prohibited.

The MCX Series of Inline MOV Chokes Offer:~ ANSI Class III Shut Off~ Linear flow characteristics~ Downstream Wear Resistant Flow Tube~ Simple Design for easy field maintenance~ Choice of materials for body standard is 316 SS~ Threaded, Flanged~ Sizes from 3” to 4” Flanged

Control Element DiscTungsten Carbide above500 psi up to maximumoperating pressure of valve.

5

MCX Actuation Packages

MCX with Electric Actuator

Actuator Shown - Indelac Male LX-14

MCX with Electric Actuator

Actuator Shown - Indelac Female LX-14

• 24 Volt DC Supply• Max Torque 3840 in. lbs.• NEMA 4 Enclosure• Side Mounted Hand wheel (optional)• Used on MCX 3” & 4”

• 24 Volt DC Supply• Max Torque 3840 in. lbs.• NEMA 4 Enclosure• Side Mounted Hand wheel (optional)• Used on MCX 3” & 4”

MCX 3” with 4” 900# RFF

MCX 4” with 6” 900# RFF

6

MC

XMCX Actuation Packages

MCX with Electric Actuator

Actuator Shown - Indelac LX-5• 24 Volt DC Supply• Max Torque 1500 in. lbs.• NEMA 4 Enclosure• Side Mounted Hand wheel (optional)• Used on MCX 3” & 4”MCX 4” with 6” 1500# RFF

MCX with Electric Actuator

Actuator Shown - Rotork IQTM 500• Single Phase 120 Volts supply• Max 500Nm torque actuator• NEMA 4 Enclosure• Side Mounted Hand wheel• Used on MCX 3” & 4”MCX 4” with 4” 1500# RFF

7

WEBEMAIL

TELFAX

Taylor Valve Technology8300 S.W. 8th StreetOklahoma City, Oklahoma 73128

www.taylorvalve.cominfo@taylorvalve.com

405.787.0145800.805.3401

I INCONEL (Optional)

03 CARBIDE DISC - STELLITE WR SLV04 CERAMIC DISC - STELLITE WR SLV 05 CARBIDE DISC - CARBIDE WR SLV15 CERAMIC DISC - NO WR SLV16 CARBIDE DISC - NO WR SLV32 CERAMIC DISC/CARBIDE FLOW TUBE44 R/RB-SERIES47 BEAN 17-4 SS

00 HNBR/HSN01 NBR03 EPDM04 FKM (VITON)05 NEOPRENE06 NBR (PEROXIDE CURED)07 STEAM SEALS09 AFLAS12 KALREZ

0 Non-flanged1 402 803 1604 XS5 XXS6 SLIP-ON7 API8 120

01 1" FNPT02 1" BUTT WELD03 1" SOCKET WELD04 1" VICTAULIC05 1" 15006 1" 30007 1" 60008 1" 900/150009 1" 250010 2" FNPT12 2" BUTT WELD13 2" SOCKET WELD14 2" VICTAULIC15 2" 15016 2" 30017 2" 60018 2" 900/150019 2" 250020 3" FNPT21 3" BUTT WELD22 3" SOCKET WELD23 3" 15024 3" 30025 3" 60026 3" 90027 3" 150028 3" 250029 4" FNPT30 4" BUTT WELD31 4" SOCKET WELD32 4" VICTAULIC33 4" 15034 4" 30035 4" 60036 4" 90037 4" 150038 4" 250039 6" 15040 6" 300

41 6" 60042 6" 90043 6" 150044 6" 250045 8" 15046 8" 30047 8" 60048 8" 90049 8" 150050 8" 250051 2-1/16" 300052 2-1/16" 500053 2-1/16" 1000054 2-9/16" 300055 2-9/16" 500056 2-9/16" 1000057 3-1/8" 300058 3-1/8" 500059 3-1/8" 1000060 4-1/16" 300061 4-1/16" 500062 1-13/16" 1000063 3-1/16" 500064 3/4" 600#65 1.5" 900/150066 3-1/16" 1000067 7-1/16" 500068 1-13/16" 1500069 2-1/16" 1500075 1" UNION76 3" 602M x 3" 602F Union

80 10" 600 81 10" 900 82 10" 150083 10" 250084 2-9/16" 1500085 6" Butt Weld

01 (2) 1/8" RND PORTS02 (2) 3/16" RND PORTS03 (2) 1/4" RND PORTS04 (2) 3/8" RND PORTS05 (2) 1/2" RND PORTS06 (2) 5/8" PIE PORTS07 (2) 3/4" RND PORTS08 (2) 7/8" RND PORTS10 (2) 1-3/16" RND PORTS11 (2) 1-1/4" RND PORTS14 (2) 1-1/2" RND PORTS30 (2) 3/4" PIE PORTS35 (2) 1" ROUND PORTS38 (2) 2" PIE PORTS40 (2) 1-1/4" PIE PORTS41 (2) 1-3/8" PIE PORTS42 (2) 1-1/8" RND PORTS47 (2) 1-1/2 PIE PORTS49 (2) 5/8" RND PORTS54 (2) 2.92 PIE HOLES55 3 CV56 12 CV57 164 CV58 420 CV59 64 CV60 35 CV22 17/64 BEAN23 18/64 BEAN24 8/64 BEAN25 13/64 BEAN26 4/64 BEAN27 38/64 BEAN28 36/64 BEAN

Inlet ConnectionOutlet Connection

Style

Schedule

Orifice Size

Trim Material

00 DUPLEX SS03 CARBON STEEL04 LOW ALLOY (4130 LACS)05 316 SS (CF8M)06 316 SS "L" (CF3M)07 ALUMINUM BRONZE08 A350 LF209 LCC11 SUPER DUPLEX SS

Body Material

Seal Material

PINS

29 48/64 BEAN34 32/64 BEAN43 40/64 BEAN44 34/64 BEAN45 28/64 BEAN46 30/64 BEAN53 10/64 BEAN63 11/64 BEAN64 14/64 BEAN65 15/64 BEAN66 16/64 BEAN67 19/64 BEAN68 20/64 BEAN69 24/64 BEAN70 21/64 BEAN71 22/64 BEAN72 23/64 BEAN73 27/64 BEAN74 29/64 BEAN75 25/64 BEAN76 1/7" RND PORTS77 7/64 BEAN78 54/64 BEAN79 44/64 BEAN80 45/64 BEAN81 47/64 BEAN82 51/64 BEAN83 35/64 BEAN84 37/64 BEAN85 6 CV87 12/64 BEAN88 78 CV

Choke Nomenclature0 Non-flanged1 RFF2 RTJ3 RFF X RTJ4 RTJ X RFF

Butt weld connections MUST specify a schedule.

All API connections are “RTJ” style by default.

API flange bore (SCHEDULE) is specified by API.

Choke part number has to be 17 digits. EXAMPLE ONLY*

REVISED: 10-05-17

1 1”2 2”3 3”4 4”6 6”

Size0 Standard1 NACE2 Steam/High Temp.

Service Type

0 Manual Handle1 Manual Gear2 Electric3 Pneumatic4 Hydraulic7 Positive Bean

Actuation Type

Choke SeriesCACIMCMCXMDAMDASMDIMDISRBR

*For more options, contact Taylor Valve.

MCX 3 0 0 27 27 1 6 35 16 05 04 = MCX-30027271635160504