CHII-DER STEVE SUH - TAMU College of Engineering · CHII-DER STEVE SUH -- January 2015 Page 5 of 21 Authorships 1. (Book) Suh, C.S. and Liu, M.-K., “Control of Cutting and Machining

CHII-DER STEVE SUH -- January 2015 Page 1 of 21

CHII-DER STEVE SUH Mechanical Engineering Department Phone: 011-2-979-845-1417 Texas A&M University Fax: 011-2-979-845-3081 College Station, TX 77843-3123, U.S.A. Email: [email protected]

PROFESSIONAL EXPERIENCE

Teaching and Research Activities Associate Professor – Mechanical Engineering Dept., Texas A&M University (2004 to date) Assistant Professor – Mechanical Engineering Dept., Texas A&M University (1998 to 2004)

Post-Doctoral Fellow - Space Power Institute and M.E. Dept., Auburn University (1997 to 1998) (Post-Doctoral) Research Associate - Mechanical Engineering Dept., TAMU (1996 to 1997) Graduate Assistant/Design Instructor - Mechanical Engineering Dept., TAMU (1992-1996) Research Assistant - Aerospace Engineering Dept., TAMU (1991-1992) Research Assistant - Mechanical Engineering Dept., Auburn University (1989-1991)

Project Management

Research Associate/Design Instructor - Design Institute (IIDE), TAMU (1994 to 1997) Residential Assistant - Housing Office, Auburn University (1989-1991)

Industry Experience Special Assistance to Director - Aerospace Industry Development Center (AIDC), Taiwan (1988-1989) Manufacturing Project Engineer - AIDC, Taiwan (1985-1988) Manufacturing Engineer - AIDC, Taiwan (1984-1985)

EDUCATION Ph.D., Texas A&M University, 1997 Major: Mechanical Engineering


TECHNICAL PUBLICATIONS

Refereed Journal Publications 1. Kuo, Chi-Wei and Suh, C.S., (2014) “Controlling Bifurcation and Dynamic Behavior in Vibro-Impact

System.” Submitted to Communications in Nonlinear Science and Numerical Simulation.

2. Wang, Xin and Suh, C.S., (2014) “Speed and Position Control of Brushed DC Motors using Nonlinear Time-Frequency Control.” Submitted to Journal of Vibration and Control.

3. Wang, Xin and Suh, C.S., (2014) “Nonlinear Time-Frequency Control of PM Synchronous Motor

Instability Applicable to Electric Vehicle Application.” International Journal of Dynamics and Control. Online First on 12-29-2014.

4. Liu, M.-K., and Suh, C.S., (2014) “Simultaneous Time-Frequency Control of Friction-Induced

Instability,” Journal of Applied Nonlinear Dynamics, 3(3), pp. 227-243. 5. Liu, M.-K., Halfmann E.B., and Suh, C.S., (2014) “Multi-Dimensional Time-Frequency Control of Micro-

Milling Instability,” Journal of Vibration and Control, 20(5), pp. 643–660.

6. Liu, M.-K., and Suh, C.S., (2013) “Synchronization of Chaos in Simultaneous Time-Frequency Domain,” Applied Mathematical Modelling, 37, pp. 9524-9537.

7. Liu, M.-K., and Suh, C.S., (2012) “Simultaneous Time-Frequency Control of Bifurcation and Chaos,”

Communications in Nonlinear Science and Numerical Simulations, 17/6, pp. 2539-2550. 8. Liu, M.-K., and Suh, C.S., (2012) “Temporal and Spectral Responses of A Softening Duffing Oscillator

Undergoing Route-To-Chaos,” Communications in Nonlinear Science and Numerical Simulations, 17/12, pp. 5217-5228.

9. Liu, M.-K., and Suh, C.S., (2012) “On Controlling Milling Instability and Chatter at High-Speed,”

Journal of Applied Nonlinear Dynamics, 1(1), pp. 59-72. 10. Vedantham, V., Suh, C.S., and Chona, R., (2011) “Laser Induced Stress Wave Thermometry for In-

Situ Temperature and Thickness Characterization of Single Crystalline Silicon Wafer Part I – Theory and Apparatus,” Experimental Mechanics, Vol. 51, pp. 1103-1114.

11. Vedantham, V., Suh, C.S., and Chona, R., (2011) “Laser Induced Stress Wave Thermometry for In-Situ Temperature and Thickness Characterization of Single Crystalline Silicon Wafer Part II – Experimental Results,” Experimental Mechanics, Vol. 51, pp. 1115-1122.

12. Qi, X., Liu, L., Suh, C.S., and Chona, R., (2010) “Elasto-Viscoplastic Wave Thermometry for Silicon

Wafer Processing,” International Journal of Applied Mechanics, Vol. 2, No. 4, pp. 827-849. 13. Qi, X., and Suh, C.S., (2010) “Elasto-Viscoplastic Response of Silicon To Femtosecond Laser Heating

at Elevated Temperature,” Journal of Thermal Stresses, Vol. 34, pp. 115-137. 14. Gegg, B., Suh, C.S., and Luo, A.C.J., (2010) “A Parameter Study of The Eccentricity Frequency and

Amplitude and Chip Length Effects on A Machine Tool With Multiple Boundaries,” Communications in Nonlinear Science and Numerical Simulations, 15/9, pp. 2575-2602.


15. Gegg, B., Suh, C.S., and Luo, A.C.J., (2010) “Modeling and Theory of Intermittent Motions In A Machine Tool With A Friction Boundary,” ASME Transactions Journal of Manufacturing Science and Engineering, Vol. 132, pp. 041001-1-9.

16. Qi, X., and Suh, C.S., (2010) “Generalized Thermo-Elastodynamics for Semiconductor Materials

Subject to Ultrafast Heating - Part I: Model Description and Validation,” International Journal of Heat and Mass Transfer, Vol. 53, pp. 41-47.

17. Qi, X., and Suh, C.S., (2010) “Generalized Thermo-Elastodynamics for Semiconductor Materials

Subject to Ultrafast Heating - Part II: Near-Field Response and Damage Evaluation,” International Journal of Heat and Mass Transfer, Vol. 53, pp. 744-752.

18. Qi, X., and Suh, C.S., (2009) “Ultrafast Laser Induced Elastodynamics in Single Crystalline Silicon -

Part I: Model Formulation,” Journal of Thermal Stresses, Vol. 32, pp. 477-493. 19. Qi, X., and Suh, C.S., (2009) “Ultrafast Laser Induced Elastodynamics in Single Crystalline Silicon -

Part II: Near-Field Response,” Journal of Thermal Stresses, Vol. 32, pp. 494-511. 20. Gegg, B., Luo, A.C.J., and Suh, C.S., (2009) “Sliding Motions On A Periodically Time-Varying

Boundary For A Friction-Induced Oscillator,” Journal of Vibration and Control, 15(5), pp. 671–703. 21. Oh, Y., Suh, C.S. and Sue H.-J., (2008) “On Failure Mechanisms in Flip Chip Assembly – Part 1: Short-

Time Scale Wave Motion,” ASME Transactions Journal of Electronic Packaging, Vol. 130, pp. 021008-1-11.

22. Oh, Y., Suh, C.S. and Sue H.-J., (2008) “On Failure Mechanisms in Flip Chip Assembly – Part 2:

Optimal Underfill and Interconnecting Materials,” ASME Transactions Journal of Electronic Packaging, Vol. 130, pp. 021009-1-9.

23. Gegg, B., Luo, A.C.J., and Suh, C.S., (2008) “Grazing Bifurcations of A Harmonically Excited Oscillator

Moving On A Time-Varying, Translation Belt,” Nonlinear Analysis: Real World Applications, Vol. 9, pp. 2156-2174.

24. Dassanayake, A.V. and Suh, C.S., (2008) “On Nonlinear Cutting Response and Tool Chatter in Turning

Operation,” Communications in Nonlinear Science and Numerical Simulations, 13/5, pp.979-1001. 25. Dassanayake, A.V. and Suh, C.S., (2007) “Machining Dynamics Involving Whirling. Part I: Model

Development and Validation,” Journal of Vibration and Control, 13(5), pp. 475-506. 26. Dassanayake, A.V. and Suh, C.S., (2007) “Machining Dynamics Involving Whirling. Part II: Machining

States Described by Nonlinear and Linearized Models,” Journal of Vibration and Control, 13(5), pp. 507-526.

27. Yang, B. and Suh, C.S., (2006) "On Fault Induced Nonlinear Response and Instability," Journal of

Mechanical Science, Vol. 48, Issue 10, pp. 1103-1125. 28. Baltaza-Lopez, M.E., Burger, C.P., Chona, R. and Suh, C.S., (2005) “Study of Wave Motion on Tubulars

Using Broadband Laser Ultrasound,” Experimental Mechanics, Vol. 45, No. 5, pp. 427-432. 29. Nagaraj, M. and Suh, C.S., (2005) “On Short Time Scale Stress Wave Phenomena and Initiation of

Mechanical Faults in Flip Chip Configurations,” IEEE Transactions on Device and Material Reliability, Vol. 5, No. 2, pp. 224-230.


30. Rabroker, G.A., Suh, C.S., and Chona, R. (2005) “Laser Induced Stress Wave Thermometry Applied to

Silicon Wafer Processing: Modeling and Experimentation," Experimental Mechanics. Vol. 45, No. 1, pp.3-8.

31. Yang, B. and Suh, C.S., (2005) "Nonlinear Characteristics of A Cracked Rotor-Journal Bearing System,"

Proc. IMechE Part K: Journal of Multi-Body Dynamics, Vol. 219, No. K1, pp. 87-108. 32. Peng, X., Yu, Y., Chan, A.K., and Suh, C.S., (2004) “Non-Contact Ultrasonic Inspection of Medical

Catheters for Polymeric Bond Defects,” Materials and Design, Vol. 25, No. 7, pp. 603-614. 33. Yang, B. and Suh, C.S., (2004) "On The Characteristics of Bifurcation and Nonlinear Dynamic

Response," ASME Transactions Journal of Vibration and Acoustics. Vol. 126, No.4, pp. 574-579. 34. Lin, Y.-J., Suh, C.S., Langari, R. and Noah, S.T., (2004) “On the Characteristics and Mechanism of

Rolling Instability and Chatter," ASME Transactions Journal of Manufacturing Science and Engineering, Vol. 125, No.4, pp. 778-786.

35. Yang, B. and Suh, C.S., (2004) "On The Nonlinear Features of Time-Delayed Feedback Oscillators,"

Communications in Nonlinear Science and Numerical Simulations, 9/5, pp.515-529. 36. Yang, B. and Suh, C.S., (2003) "Interpretation of Crack Induced Nonlinear Response Using

Instantaneous Frequency," Mechanical Systems and Signal Processing, Vol. 18, No. 3, pp. 491-513. 37. Yang, B, Suh, C.S., and Chan, A.K., (2002) "Characterization and Detection of Crack-Induced Rotary

Instability," ASME Transactions Journal of Vibration and Acoustics, Vol. 124, No.1, pp. 40-48. 38. Suh, C.S., Khurjekar, P.P., and Yang, B., (2002) "Characterization and Identification of Dynamic

Instability in Milling Operation," Mechanical Systems and Signal Processing, Vol. 16, No. 5, pp. 829-848.

39. Harms, K.D. and Suh, C.S., (2002) “Laser-Optic Evaluation for Bond Quality of Polymeric Medical

Tubing," ASME Transactions Journal of Pressure Vessel Technology, Vol. 124, pp. 283-292. 40. Lin, Y.-J., Suh, C.S. and Noah, S.T., (2002) “Dynamic Characteristics of Sheet Rolling Instability,"

International Journal of Structural Stability and Dynamics, Vol. 2, No. 3, pp. 375-394. 41. Yang, B, Suh, C.S., and Chan, A.K., (2002) "Wavelet-Based Algorithms for Crack Detection in Rotor-

Machines," International Journal of Condition Monitoring and Diagnostic Engineering Management, Vol. 6, No. 1, pp. 31-40.

42. Chona, R., Suh, C.S., and Rabroker, G.A., (2003) "Characterizing Defects in Multi-Layer Materials Using

Guided Ultrasonic Waves," Optics and Lasers in Engineering, Vol. 40, Issue 4, pp.371-378. 43. Suh, C.S., and Burger, C.P., (1998) “Thermoelastic Modeling of Laser-Induced Stress Waves in Plates,”

Journal of Thermal Stresses, Vol. 21, No. 8, pp. 829-847.

44. Suh, C.S., and Burger, C.P., (1998) “Effects of Thermo-Mechanical Coupling and Relaxation Times on Wave Spectrum in Dynamic Theory of Generalized Thermoelasticity,” ASME Transactions Journal of Applied Mechanics, Vol. 65, No. 3, pp. 605-615.


Authorships

1. (Book) Suh, C.S. and Liu, M.-K., “Control of Cutting and Machining Instability –Time-Frequency Approach for Precision, Micro and Nano Machining,” John Wiley & Sons, 2013. ISBN 978-1-118-37182-4.

2. (Book) Gegg, B., Suh, C.S., and Luo, A.C.J., “Machine Tool Vibrations and Cutting Dynamics,” Springer Science, New York, N.Y., 2011. ISBN 978-1-4419-9800-2. e-ISBN 978-1-4419-9801-9.

3. (Book Chapter) Qi, X. and Suh, C.S., (2013), “Ultrafast Laser-Induced Thermoelastic Responses in Semiconductors,” Encyclopedia of Thermal Stresses (ed. R. B. Hetnarski), Springer Science, 2014. ISBN 978-94-007-2739-7.

4. (Book Chapter) Qi, X. and Suh, C.S., (2013), “Thermodynamics for Silicon Materials Subjected to

Ultrafast Laser Heating,” Encyclopedia of Thermal Stresses (ed. R. B. Hetnarski), Springer Science, 2014. ISBN 978-94-007-2739-7.

5. (Book Chapter) Qi, X. and Suh, C.S., (2013), “Temperature Characterization in Silicon Wafer by Using

Stress Wave as An Indicator,” Encyclopedia of Thermal Stresses (ed. R. B. Hetnarski), Springer Science, 2014. ISBN 978-94-007-2739-7.

6. (Book Chapter) Gegg, B., Suh, C.S., and Luo, A.C.J., “Chapter 3 – Analytical Prediction of Interrupted

Cutting Periodic Motions in A Machine Tool,” Nonlinear Science and Complexity (eds., J.A.T. Machado et al.), Springer Science, 2011. ISBN 978-90-481-98883-2.

7. (Book Chapter) Gegg, B., Suh, C.S.,and Luo, A.C.J., “Chapter 8 - A Parameter Study of A Machine Tool

with Multiple Boundaries,” Dynamical Systems: Discontinuity, Stochasticity and Time Delay (ed., A.C.J. Luo), Springer Verlag, 2010.

8. (Book Chapter) Luo, A.C.J., Gegg, B., and Suh, C.S., “Grazing Phenomena in A Harmonically Excited Oscillator With Dry-Friction On A Sinusoidally Time-Varying Traveling Surface,” Transactions of Nonlinear Science & Complexity (eds., A.C.J. Luo, L. Dai, and H.R. Hamidzadeh), Vol. 1, pp. 121-133, World Scientific, 2007.

9. (Book Chapter) Dassanayake, A.V. and Suh, C.S., “A 3D Turning Model for The Interpretation of

Machining Stability and Chatter,” Transactions of Nonlinear Science & Complexity (eds., A.C.J. Luo, L. Dai, and H.R. Hamidzadeh), Vol. 1, pp. 149-163, World Scientific, 2007.

Editorships

1. Associate Editor, Journal of Applied Nonlinear Dynamics, 2011-date.

2. Guest Editor, Journal of Vibration and Control, Vol. 13, No. 5, May 2007.

Invited Seminars

1. “Nonlinear Time-Frequency Control Theory with Applications,” Nanjing Research Institute for Agricultural Mechanization Ministry of Agriculture (NRIAM), 12-26-2014.

2. “IIDE Design Methodology: Need Analysis,” Nanjing Research Institute for Agricultural Mechanization Ministry of Agriculture (NRIAM), Nanjing, China, 12-26-2014.


3. “Progress Made in Macro and Micro Machining,” South China Agricultural University (SCAU), Guanzhou, China, 12-23-2014.

4. “Fostering Innovation in Mechanical Engineering Design Education at Texas A&M University,” South China Agricultural University (SCAU), Guanzhou, China, 12-24-2014.

5. “Fostering Innovation in Mechanical Engineering Design Education at Texas A&M University,”

Nanjing Research Institute for Agricultural Mechanization Ministry of Agriculture (NRIAM), Nanjing, China, 6-11-2014.

6. “Nonlinear Time-Frequency Control of Chatter and Cutting Instability at High Speed,” Nanjing Research Institute for Agricultural Mechanization Ministry of Agriculture (NRIAM), Nanjing, China, 6-11-2014.

7. “Axiomatic Design and IIDE Design Methodologies,” College of Engineering, China Agricultural University, 6-2-2014.

8. “Design for Manufacture,” Shandong Wuzheng Group, Rizhao, Shandong Province, China, 5-30-2014. 9. “Ultrafast Laser Induced Thermo-Elasto-Visco-Plastodynamics in Semiconductor Materials,” School of

Mathematics and Physics, Suzhou University of Science and Technology, 5-22-2014. 10. “Nonlinear Time-Frequency Control of Chatter and Cutting Instability at High Speed,” Taiwan

Machine Tool & Accessory Builders’ Association (TMBA), Taichung, Taiwan, 1-9-2014. 11. “Nonlinear Time-Frequency Control of Chatter and Cutting Instability at High Speed,” Taiwan

Machine Tool & Accessory Builders’ Association (TMBA), Taichung, Taiwan, 1-9-2014. 12. “Mitigation of Chatter and Cutting Instability at High Speed,” Industrial Technology Research Institute

(ITRI), Hsinchu, Taiwan, 7-8-2013.

13. “Simultaneous Time-Frequency Control of High-Speed Milling and Multi-Dimensional Micro-Milling Instability,” Industrial Technology Research Institute (ITRI), Hsinchu, Taiwan, 7-8-2013.


Industrial Technology Research Institute (ITRI), Hsinchu, Taiwan, 7-8-2013.

15. “Simultaneous Time-Frequency Control Applying to Synchronization of Chaos,” Shenyang Aerospace University, China, 6-28-2013.

16. “Mitigation of Micro-milling Chatter at High Speed,” Shenyang Aerospace University, China, 6-24-2013.

17. “Publish or Perish: A Workshop on Publishing with SCI-Indexed Journals,” College of Engineering,

China Agricultural University, 5-27-2013.

18. “Power Density: An Alternative to Characterizing Fatigue Performance Subject to Variable Loading and Impact,” Schlumberger 2012 EUREKA Mechanical Workshop – Problem, Cause & Solution (PCS), Houston, Texas, 8-22-2012.

19. “Mitigation of Chatter and Cutting Instability at High Speed,” Schlumberger CHPC, Houston, Texas, 11-02-2011.



Schlumberger CHPC, Houston, Texas, 11-02-2011. 21. “ABET-Accredited Mechanical Engineering Program at Texas A&M University – An Overview,”

College of Engineering, China Agricultural University, 6-28-2010.

22. “Fostering Innovation in Mechanical Engineering Design Education at Texas A&M University,” College of Engineering, China Agricultural University, 6-28-2010.

23. “IIDE Design Methodologies and Advanced Structural-Web Molding Technology,” College of Engineering, China Agricultural University, 6-29-2010.

24. “Laser Ultrasonic Thermometry for In-Situ Characterization of Semiconductor Material,” College of Engineering, China Agricultural University, 6-29-2010.

25. “Short-Time Scale Dynamic Failure Modes in A Through-Silicon-Via (TSV) Flip-Chip Configuration,”

College of Engineering, China Agricultural University, 6-30-2010.

Disclosure of Invention “UDIMC – Universal Dynamic Instability Mitigation and Control,” 2011. (TAMUS 3448 Disclosure

of Invention filed through TAMUS Office of Technology Commercialization (OTC) on June 21, 2011.) "Thermo-Acousto-Photonic Nondestructive Evaluation (TAP-NDE) and the Gabor Wavelet

Transform (GWT) Applied to Quality Inspection of Small Diameter Polymeric Catheter Tubing," 2001. (TAMUS Disclosure of Invention 1739TEES01. Provisional patent application filed on April 23, 2002.)

Conference Proceedings and Presentations

1. (Peer Reviewed) Wang, X., and Suh, C.S., (2014) “Simultaneous Time-Frequency Control of

Permanent Magnet Synchronous Motor,” The 16th European Conference on Power Electronics and Application, EPE’14-ECCE Europe, August 26-28, 2014, Lappeenranta, Finland.

2. (Peer Reviewed) Liu, M., and Suh, C.S., (2014) “Nonlinear Time-Frequency Control of Active

Magnetic Bearings at High Speed,” IMECE2014-37168, ASME 2014 International Mechanical Engineering Congress and Exhibition (IMECE2014), November 14-20, 2014, Montreal, Canada.

3. (Peer Reviewed) Tong, X., and Suh, C.S., (2014) “Wavelet-based Filtered-X-LMS Algorithm for the

Control of Permanent Magnet Synchronous Motors,” IMECE2014-37363, ASME 2014 International Mechanical Engineering Congress and Exhibition (IMECE2014), November 14-20, 2014, Montreal, Canada.

4. (Peer Reviewed) Kuo, C.-W., and Suh, C.S., (2014) “Controlling Bifurcation and Dynamic Behavior in

Vibro-Impact System,” IMECE2014-38281, ASME 2014 International Mechanical Engineering Congress and Exhibition (IMECE2014), November 14-20, 2014, Montreal, Canada.

5. (Peer Reviewed) Liu, M.-K., and Suh, C.S., (2013) “Simultaneous Time-Frequency Synchronization of

Non-Autonomous Chaotic System,” IMECE2013-65378, ASME 2013 International Mechanical Engineering Congress and Exhibition (IMECE2013), November 15-21, 2013, San Diego, California.


6. (Peer Reviewed) Liu, M.-K., and Suh, C.S., (2013) “Control of Friction-Induced Instability in Simultaneous Time-Frequency Domain,” IMECE2013-65382, ASME 2013 International Mechanical Engineering Congress and Exhibition (IMECE2013), November 15-21, 2013, San Diego, California.

7. (Peer Reviewed) Liu, M.-K., and Suh, C.S., (2013) “Simultaneous Time-Frequency Control of Active

Magnetic Bearings,” IMECE2013-65416, ASME 2013 International Mechanical Engineering Congress and Exhibition (IMECE2013), November 15-21, 2013, San Diego, California.

8. (Peer Reviewed) Kuo, C.-W., and Suh, C.S., (2013) “Guided Wave Propagation in Tubular Section with

Multi-Layered Viscoelastic Coating Part I – Axial Waves,” IMECE2013-65386, ASME 2013 International Mechanical Engineering Congress and Exhibition (IMECE2013), November 15-21, 2013, San Diego, California.

9. (Peer Reviewed) Kuo, C.-W., and Suh, C.S., (2013) “Guided Wave Propagation in Tubular Section with

Multi-Layered Viscoelastic Coating Part II – Circumferential Waves,” IMECE2013-65390, ASME 2013 International Mechanical Engineering Congress and Exhibition (IMECE2013), November 15-21, 2013, San Diego, California.

10. (Peer Reviewed) Halfmann, E.B., Suh, C.S., and Hung, N.P. (2012) “Turning Dynamics Part I:

Experimental Analysis,” IMECE2012-87933, ASME 2012 International Mechanical Engineering Congress and Exhibition (IMECE2012), November 9-15, 2012, Houston, Texas.

11. (Peer Reviewed) Halfmann, E.B., Suh, C.S., and Hung, N.P. (2012) “Turning Dynamics Part II: Stability at High Speed,” IMECE2012-87939, ASME 2012 International Mechanical Engineering Congress and Exhibition (IMECE2012), November 9-15, 2012, Houston, Texas.

12. (Peer Reviewed) Halfmann, E.B., and Suh, C.S., (2012) “High Speed Nonlinear Micro Milling

Dynamics,” MSEC2012-7287, Annual International Manufacturing Science and Engineering Conference (MSEC 2012), June 4-8, 2012, at University of Notre Dame.

13. (Peer Reviewed) Halfmann, E.B., and Suh, C.S., (2012) “Impact of Spindle Speed on Micro-Milling Stability,” IMECE2012-88071, ASME 2012 International Mechanical Engineering Congress and Exhibition (IMECE2012), November 9-15, 2012, Houston, Texas.

14. (Peer Reviewed) Liu, M.-K., Halfmann, E.B., and Suh, C.S., (2012) “Simultaneous Time-Frequency

Control of Multi-Dimensional Micro-Milling Instability,” IMECE2012-88026, ASME 2012 International Mechanical Engineering Congress and Exhibition (IMECE2012), November 9-15, 2012, Houston, Texas.

15. (Peer Reviewed) Liu, M.-K., and Suh, C.S., (2012) “Mitigation of Milling Chatter at High-Speed,”

IMECE2012-88080, ASME 2012 International Mechanical Engineering Congress and Exhibition (IMECE2012), November 9-15, 2012, Houston, Texas.

16. (Peer Reviewed) Dassanayake, A.V. and Suh, C.S., (2012) “Impact of Coupled Whirling and Tool Geometry on Machining Dynamics,” IMECE2012-87954, ASME 2012 International Mechanical Engineering Congress and Exhibition (IMECE2012), November 9-15, 2012, Houston, Texas.

17. (Peer Reviewed) Dassanayake, A.V. and Suh, C.S., (2012) “Effects of Spindle Speed on Turning

Stability,” IMECE2012-87996, ASME 2012 International Mechanical Engineering Congress and Exhibition (IMECE2012), November 9-15, 2012, Houston, Texas.


18. (Peer Reviewed) Liu, M.-K., and Suh, C.S., (2012) “Synchronization of A Non-Autonomous Chaotic System in Simultaneous Time-Frequency Domain,” 2012 International Conference on Nonlinear Dynamics and Complexity (NDC2012), July 23-29, 2012, Jinan, Shandong, China.

19. (Presentation) Suh, C.S., (2011) “Thermomechanical Responses of Silicon To Ultrafast Laser Heating

At Elevated Temperature,” The 48th Annual Technical Conference of The Society of Engineering Sciences (SES2011), October 12-14, 2011, at Northwestern University.

20. (Peer Reviewed) Liu, M.-K. and Suh, C.S., (2011) “Simultaneous Time-Frequency Chaos Control,” The

3rd International Conference on Dynamics, Vibrations, and Control (DVC2011), Calgary, Canada, August 8-13, 2011.

21. (Peer Reviewed) Liu, M.-K. and Suh, C.S., (2011) “Control of High Speed Milling Chatter in

Simultaneous Time-Frequency Domain ,” DETC2011-47921, ASME 2011 International Design Engineering Technical Conferences (IDETC) and Computers and Information in Engineering Conference (CIE), August 2011.

22. (Peer Reviewed) Liu, M.-K. and Suh, C.S., (2010) “Temporal and Spectral Responses of A Softening Duffing Oscillator,” 2010 ASME DSCC, Oct. 2010.

23. (Peer Reviewed) Qi, X. and Suh, C.S., (2010) “Design and Optimization of Mechanical Control Lines

Using CAD/CAE Integration,” IMECE2010-37791, 2010 ASME International Mechanical Engineering Congress & Exposition, Nov. 2010.

24. (Peer Reviewed) Gegg, B. and Suh, C.S., (2010) “Characteristics and Effects on a Machine-Tool due to

Grazing Motions of a Friction Boundary,” IMECE2010-37929, 2010 ASME International Mechanical Engineering Congress & Exposition, Nov. 2010.

25. (Peer Reviewed) Gegg, B. and Suh, C.S., (2010) “Sensitivity of Steady State Intermittent Cutting

Motion To Work-Piece Characteristics,” NSC, 2010. 26. (Peer Reviewed) Qi, X. and Suh, C.S., (2010) “Design and Optimization of Mechanical Control Lines

Using CAD/CAE Integration,” IMECE2010-37791, 2010 ASME International Mechanical Engineering Congress & Exposition, Nov. 2010.

27. (Peer Reviewed) Gegg, B. and Suh, C.S., (2010) “Characteristics and Effects on a Machine-Tool due to

Grazing Motions of a Friction Boundary,” IMECE2010-37929, 2010 ASME International Mechanical Engineering Congress & Exposition, Nov. 2010.

28. (Peer Reviewed) Gegg, B. and Suh, C.S., (2010) “Sensitivity of Steady State Intermittent Cutting

Motion To Work-Piece Characteristics,” IMECE2010-34186, 2010 ASME International Mechanical Engineering Congress & Exposition, Nov. 2010.

29. (Peer Reviewed) Gegg, B. and Suh, C.S., (2010) “Sensitivity of Steady State Intermittent Cutting Motion To Work-Piece Characteristics,” NSC, 2010.

30. (Peer Reviewed) Gegg, B. and Suh, C.S., (2010) “Sensitivity of Steady State Intermittent Cutting Motion To Work-Piece Characteristics,” MSEC ICMP2010‐34186, 2010 ASME International Manufacturing Science & Engineering Conference, Erie, Pennsylvania.


31. (Peer Reviewed) Gegg, B. and Suh, C.S., (2009) “A Parameter Study of The Eccentricity Frequency and Amplitude Effects on A Machine Tool with Multiple Boundaries,” 2009 Conference on Dynamics, Vibration and Control, Aug. 10-15, 2009, Chengdu, China.

32. (Peer Reviewed) Gegg, B. and Suh, C.S., (2009) “Effects of Chip Seizure on Steady State Motion of A Machine Tool,” MSEC ICMP2009‐84280, 2009 ASME International Conference on Manufacturing Science & Engineering, Oct. 2009.

33. (Peer Reviewed) Qi, X. and Suh, C.S., (2008) “Thermomechanical Characteristics of Silicon Wafer In

Response to Ultrafast Laser Heating,” IMECE2008-66329, 2008 ASME International Mechanical Engineering Congress & Exposition, Nov. 2008.

34. (Peer Reviewed) Gegg, B., Suh, C.S., and Luo, A.C.J., (2008), “Analytical Prediction of Motions in A

Machine Tool With Loss of Effective Chip Contact,” IMECE2008-67109, 2008 ASME International Mechanical Engineering Congress & Exposition, Nov. 2008.

35. (Peer Reviewed) Gegg, B., Suh, C.S., and Luo, A.C.J., (2008), “Stick and Non-Stick Periodic Motions of

A Machine Tool in The Cutting Process,” MSEC ICMP2008/DYN‐72052, 2008 ASME International Conference on Manufacturing Science & Engineering, Oct. 2008.

36. (Peer Reviewed) Gegg, B., Suh, C.S., and Luo, A.C.J., (2008), “Analytical Prediction of Interrupted

Cutting Periodic Motions in A Machine Tool,” NSC-97, The Second International Conference on Nonlinear Science and Complexity, Porto, Portugal, July 26‐31, 2008.

37. (Peer Reviewed) Liu, L. and Suh, C.S., (2007), “Elasto-Viscoplastic Waves Silicon Wafers,” DETC2007-

35399, 2007 ASME International Design Engineering Technical Conferences & Computers and Information in Engineering Conference, Sept. 2007

38. (Peer Reviewed) Dassanayake, A.V. and Suh, C.S., (2007), “Impact of Tool Geometry on Cutting

Dynamics,” DETC2007-35472, 2007 ASME International Design Engineering Technical Conferences & Computers and Information in Engineering Conference, Sept. 2007.

39. (Peer Reviewed) Gegg, B., Suh, C.S., and Luo, A.C.J., (2007), “Periodic Motions of A Two Degree of

Freedom Oscillator with Cutting Process Applications,” DETC2007-35166, 2007 ASME International Design Engineering Technical Conferences & Computers and Information in Engineering Conference, Sept. 2007.

40. (Peer Reviewed) Luo, A.C.J., Gegg, B., and Suh, C.S., (2006), “The Stick Motion of A Harmonically

Excited, Friction-Induced Oscillator on A Sinusoidally Traveling Surface,” IMECE2006-13804, 2006 ASME International Mechanical Engineering Congress & Exposition, Nov. 2006.

41. (Peer Reviewed) Shenoy, S., Dixit, M., Nandagopalan, A.S., Schubert, J., Peterman, C., and Suh, C.S.,

(2006), “Top Hole Dual Gradient Drilling System A Strategic Approach Towards Deepwater Drilling,” 2006 SPE/IADC Conference on Managed Pressure Drilling & Underbalanced Operations, Galveston, Texas, March 2006.

42. (Peer Reviewed) Dassanayake, A.V. and Suh, C.S., (2005) “A Comprehensive Model for Cutting

Dynamics,” IDETC2005-85075, 2005 ASME International Design Engineering Technical Conferences & Computers and Information in Engineering Conference, Sept. 2005.


43. (Peer Reviewed) Dassanayake, A.V. and Suh, C.S., (2005) “A Study of Whirling and Significance of Nonlinearity on Cutting Dynamics,” Paper M4A-3, 3rd International Conference on Structural Stability and Dynamics, June 2005.

44. (Peer Reviewed) Yang, B. and Suh, C.S., (2005) “On The Nonlinear Rotary Response and Instability,”

Paper W1B-3, 3rd International Conference on Structural Stability and Dynamics, June 2005. 45. (Peer Reviewed) Liu, L. and Suh, C.S., (2005) “Elasto-Viscoplastic Wave Propagation in Single

Crystallographic Silicon Thin Structures,” Paper W4B-1, 3rd International Conference on Structural Stability and Dynamics, June 2005.

46. (Peer Reviewed) Nagaraj, M. and Suh, C.S., (2005) “Short Time Scale Thermal-Mechanical Wave

Propagation in High Performance Microelectronic Devices,” Paper W4A-2, 3rd International Conference on Structural Stability and Dynamics, June 2005.

47. (Peer Reviewed) Michalec, C. and Suh, C.S., (2005) “Expanding Tube Energy Absorber and Deforming

Angle Energy Absorber,” 3rd International Conference on Structural Stability and Dynamics, June 2005.

48. Kulkarni, T.R. and Suh, C.S., (2005) “Optimal Design Solutions for Crew Exploration Vehicle,” AIAA

Space 2005 Conference, Sept. 2005. 49. Kulkarni, T.R. and Suh, C.S., (2005) “Crew Exploration Vehicle: Need Analysis and Function

Structure for Structural System,” AIAA Annual Technical Symposium, Houston, May 2005. 50. Kulkarni, T.R. and Suh, C.S., (2005) “Crew Exploration Vehicle: Optimal Design Solutions and

Configuration,” AIAA Region IV Student Conference, April 2005. 51. (Peer Reviewed) Jalan, M., Chona, R. and Suh, C.S., (2004) "A Robust Design For Automatic Positioning

of Fiber-Tip Interferometer,” Proceedings of 2004 SEM Annual Conference and Exposition on Experimental and Applied Mechanic.

52. (Peer Reviewed) Baltaza, M.E., Burger, C.P., Chona, R. and Suh, C.S., (2004) “Study on Laser-Generated

Ultrasonic Waves on Cylindrical Surfaces,” Proceedings of 2004 SEM Annual Conference and Exposition on Experimental and Applied Mechanics.

53. (Peer Reviewed) Jalan, M., Suh, C.S., and Chona, R., (2003) "A Robust Fiber-Tip Interferometer System

for The Sensing of Transient Out of Plane Displacements,” Proceedings of 2003 SEM Annual Conference and Exposition on Experimental and Applied Mechanics.

54. (Peer Reviewed) Vedantham, V., Rabroker, G.A., Suh, C.S., and Chona, R., (2003) “Simultaneous

Non-Contact Temperature and Film Thickness Measurement – Experimental Evaluation,” Proceedings of 2003 SEM Annual Conference and Exposition on Experimental and Applied Mechanics.

55. (Peer Reviewed) Vedantham, V., Rabroker, G.A., Suh, C.S., and Chona, R., (2003) “Simultaneous

Non-Contact Temperature and Film Thickness Measurement – Analytical Consideration,” Proceedings of 2003 SEM Annual Conference and Exposition on Experimental and Applied Mechanics.

56. (Peer Reviewed) Vedantham, V., and Suh, C.S., (2002) "Non-contact Laser Ultrasonics for

Temperature Monitoring in Wafer Processing," Proceedings of 2003 ASNT Annual Congress, November 4-8.


57. (Peer Reviewed) Vedantham, V., Thummalapalli, A., Yang, B., and Suh, C.S., (2002) " Laser Ultrasonic Characterization of Cryogenically Cycled Epoxy Composites,” Proceedings of 2003 ASNT Annual Congress, November 4-8.

58. (Peer Reviewed) Oh, Y., Suh, C.S., and Sue, H.-J., (2002) "On The Dynamic Short-Time Scale Wave

Propagation and The Characterization of Optimal Packaging Material for High Performance Electronic Packages," Proceedings of ASME IMECE2002-34669.

59. (Peer Reviewed) Yang, B., Fisher, J., and Suh, C.S., (2002) "Characterization of Dynamical Instability

Using Instantaneous Frequency," Proceedings of ASME IMECE2002-34226. 60. (Peer Reviewed) Vedantham, V., Thummalapalli, A., Yang, B., and Suh, C.S., (2002) "Non-Contact Laser

Ultrasonic Inspection for Cryogenically Introduced Interlayer Defects in Epoxy-Based Composites," Proceedings of ASME IMECE2002-33452.

61. (Peer Reviewed) Lin, Y.-J., Suh, C.S., and Noah, S.T., (2002) "On The Causes of Rolling Instability and

Chatter," Proceedings of ASME IMECE2002-32392. 62. (Peer Reviewed) Yang, B. and Suh, C.S., (2002) "Mechanical Fault Diagnosis Using Numerical Hilbert

Transform," Proceedings of ASME ETCE2002/STRUC-29005. 63. (Peer Reviewed) Harms, K.D. and Suh, C.S., (2001) “Quality Inspection of Polymeric Medical Tubing

Using Non-Contact TAP-NDE," Proceedings of the ASME 7th Nondestructive Evaluation Topical Conference - Manufacturing Innovations and Their Impact on NDE.

64. (Peer Reviewed) Harms, K.D., Yang, B., and Suh, C.S., (2001) "Characterization of Bond Quality for

Polymeric Medical Tubing," Proceedings of ASME IMECE 2001. 65. Lin, Y.-J., Suh, C.S., and Noah, S.T., (2001) "Analysis of Chatter Dynamics in Sheet Rolling," Proceeding

of IMAX-XIX, April 2001. 66. Weaver, J., Gam, K.T., Oh, Y., Bonnaud, L., Suh, C.S., Sue, H.-J., Todd, M., Ji, Q., Edwards, M., (2001)

"Improving the Reliability and Performance of Microelectronic Packaging," Proceedings of ANTEC 2001.

67. (Peer Reviewed) Suh, C.S. and Chan, A.K. (2000) “Wavelet-Based Technique for Detection of

Mechanical Chaos," Proceeding of SPIE, Vol. 4056, pp. 267-274.

68. (Peer Reviewed) Yang, B., Suh, C.S., and Chan, A.K., (2000) “Wavelet-Based Technique for Detection of Mechanical Chaos," Proceeding of 13th International Congress on Condition Monitoring and Diagnostic Engineering Management (COMADEM 2000), pp. 155-164.

69. Suh, C.S., Rabroker, G.A., Chona, R., and Burger, C.P., (1999) “Thermal-Acousto-Photonics for Non

contact Temperature Measurement in Silicon Wafer Processing,” Proceeding of SPIE, Vol. 3783, pp. 184-193.

70. Rabroker, G.A., Suh, C.S., Chona, R., and Burger, C.P. (1998) “Lamb Wave Propagation as a

Temperature Diagnostic in Silicon Wafer Processing: Some Analytical Considerations," Proceeding of the 1998 SEM Spring Conference on Experimental Mechanics, pp459-461.


71. Suh, C.S., Rabroker, G.A., Chona, R., and Burger, C.P. (1998) “Lamb Wave Propagation as a Temperature Diagnostic in Silicon Wafer Processing: Experimental Implementation and Results," Proceedings of the 1998 SEM Spring Conference on Experimental Mechanics, pp455-458.

72. Rabroker, G.A., Suh, C.S., Burger, C.P., and Chona, R. (1997) “Analytical Feasibility of Laser Induced

Stress Waves Thermometry Applied to Silicon Wafers,” Proceedings of the ASME Symposium on Applications of Experimental Mechanics to Electronic Packaging, EEP-Vol. 22/AMD-Vol. 226, pp. 45-50.

73. Suh, C.S., Rabroker, G.A., Burger, C.P., and Chona, R. (1997) “Ultrasonic Time-Frequency

Characterization of Silicon Wafers at Elevated Temperatures,” Proceedings of the ASME Symposium on Applications of Experimental Mechanics to Electronic Packaging, EEP-Vol. 22/AMD-Vol. 226, pp. 37-44.

74. Suh, C.S., Burger, C.P., DeCarvalho, E.A., and Chona, R., (1997) “A Proposed Thermoelastic Model for

Laser-Generated Ultrasound,” Proceedings of the Second International Symposium on Thermal Stresses and Related Topics, pp. 705-708, Rochester, New York.

75. Suh, C.S., and Burger, C.P., (1997) “Experimental Time-Frequency Analysis of Laser-Induced Lamb

Waves,” Proceedings of the 1997 SEM Spring Conference on Experimental Mechanics, pp. 279-280, Bellevue, Washington.

76. Burger, C.P. and Suh, C.S., (1997) “An Optical Method for Non-Invasive Quality Control,” Proceedings

of the 1997 SEM Spring Conference on Experimental Mechanics, pp. 174-175, Bellevue, Washington.

77. Burger, C.P., Suh, C.S., and Condoor, S.S., (1996) “Design Methods and Principles for Efficient Product Creation,” in the technical notebook of Valve Manufacturer Association 1996 Technical Seminar, College Station, Texas, November 7-8.

78. Condoor, S.S,, Suh, C.S., and Burger, C.P. (1996) “Educating Practicing Engineers on How to Manage

and Execute Product Creation Process,” Proceedings of the ASEE Gulf Southwest Section 1996 Annual Conference, San Antonio, Texas, March 27-29.

79. Condoor, S.S., Suh, C.S., Burger, C.P. (1995) “Creating an Innovative Design Program at Texas A&M

University,” Proceedings of the World Conference on Engineering Education: Restructuring Engineering Education for Meeting World Needs, Ed. by Kruger, E.R. and Kulacki, F.A., pp. 137-139.

Graduate Student Supervision Completed PhD: Meng-Kun Liu (December 2012) Dissertation Title: "Nonlinear Time-Frequency Control Theory with Applications” PhD: Xuele Qi (December 2009) Dissertation Title: "Ultrafast Laser Induced Thermo-Elasto-Visco-Plastodynamics in Single

Crystalline Silicon” PhD: Brandon Gegg (May 2009) Dissertation Title: "An Investigation of The Complex Motions Inherent To Machining

Systems via A Discontinuous Systems Theory Approach”


PhD: Achala Dassanayake (August 2006) Dissertation Title: "Machining Dynamics and Stability Analysis in Longitudinal Turning

Involving Workpiece Whirling" PhD: Yoonchan Oh (August 2004) Dissertation Title: "Multiphysics Investigation on The Failure Mechanism and Short-Time

Scale Wave Motion in Flip-Chip Configuration" PhD: Baozhong Yang (August 2003. Co-Chaired with A.K. Chan) Dissertation Title: "On The Characterization of Fault-Induced Rotor-Dynamic Bifurcations

and Nonlinear Responses" PhD: Yun-Jeng Lin (August 2002. Co-Chaired with S.T. Noah) Dissertation Title: "Characterization of Dynamic Instability in Metal Sheet Rolling" MS: Mengke Liu (May 2015) Tentative Thesis Title: "Investigation on The Applicability of Active Magnetic Bearings to

High Speed Spindle Design" MS: Sandip Hodkhasa (May 2013) Thesis Title: "Wave Propagation and Damage Characterization in Natural Fiber HEMP and

LLDPE Composite" MS: Chi-Way Kuo (December 2012) Thesis Title: "Guided Wave Propagation in Tubular Section with Multi-Layered Viscoelastic

Coating" MS: Eric B. Halfmann (August 2012) Thesis Title: "On The Machining Dynamics of Turning and Micro-Milling Processes" MS: Chang-Chia Huang (August 2009) Thesis Title: "Short-Time Scale Dynamic Failure Modes In A Through-Silicon-Via (TSV)

Flip-Chip Configuration" MS: Neelima Erukulla (Fall 2008) Thesis Title: "Characterization of Pipe Coating Flaw Using Guided Waves" MS: Abduljaleel Alhaddad (August 2008. MS Non-Thesis) MS: Patrick Zhiyuan Ma (August 2007. MS Non-Thesis) MS: Amol Dixit (May 2006. MS Non-Thesis) MS: Li Liu (May 2005) Thesis Title: "Elasto-Viscoplastic Wave Propagation in A Single Crystallographic Silicon

Thin Structure" MS: Ibrahim M. Khalil (May 2005) Thesis Title: "Fatigue Crack Propagation in Polymers" MS: Chris Michlac (August 2005)


Thesis Title: “Converting The Kinetic Energy of A Moving Vehicle into Strain Energy and Heat of Steel Deformation To Be Implemented Into Highway Safety Crash Cushions”

MS: Tzu-Wei Lo (August 2005) Thesis Title: "A New Sensor Concept for Simultaneous Measurement of Pressure,

Temperature and Thickness of Plate Structures Using Modified Wave Propagation Theory"

MS: Mahavir Nagaraj (August 2004) Thesis Title: "Short Time Scale Thermal Mechanical Shock Wave Propagation in High

Performance Microelectronic Packaging Configuration” MS: Hakan Ozaltun (May 2004) Thesis Title: "MEMS and Multi-Physics Analysis of Micro Motor by ANSYS” MS: Vikram Vedantham (August 2003) Thesis Title: "In-situ Temperature and Thickness Characterization for Silicon Wafers

Undergoing Thermal Annealing” MS: Isaac F. Salazar (August 2003) Thesis Title: "Damage Identification in an Eight Degree-of-Freedom System Using

Instantaneous Frequency" MS: Prasanna Joshi (August 2003. MS Non-Thesis. Co-Chaired with Ravi Chona) MS: Sanjay Tiwari (December 2002) Thesis Title: "A Quantitative and Objective Evaluation Approach for Optimal Selection of

Design Concept in Conceptual Design Stage" MS: Shavkat Madaminov (May 2002) Thesis Title: "Boeing-757 Nose Landing Gear Light Housing Design" MS: Jana Weaver (August 2001. Co-Chaired with H.J. Sue) Thesis Title: “Improving the Reliability of Microelectronic Packaging Through Core-Shell

Rubber Technology” MS: Choon-Sik Jhun (December 2001)

Thesis Title: "Characterization of Residual Stress Relaxation In Welded Steel Plates Using TAP-NDE and Wavelets."

MS: Kent D. Harms (May 2001) Thesis Title: "Quality Inspection of Small Diameter Polymeric Medical Tubing and Attached

Wire Stent Using TAP-NDE and the Gabor Wavelet Transform." MS: Parag P. Khurjekar (December 2000) Thesis Title: "Detection of Instabilities and Transition in Milling Operation Using

Wavelets." In Progress PhD: Chi-Way Kuo (Anticipated graduation date: December 2015) Tentative Dissertation Title: TBD


PhD: Xin Wang (Anticipated graduation date: December 2016) Tentative Dissertation Title: TBD PhD: Shangguan Lantien (Anticipated graduation date: December 2017) Tentative Dissertation Title: TBD PhD: Xu Mao (Anticipated graduation date: December 2016) Tentative Dissertation Title: TBD PhD: Mengke Liu (Anticipated graduation date: December 2018) Tentative Dissertation Title: TBD MS: Evan Wright (Anticipated graduation date: August 2016) Tentative Thesis Title: TBD MS: Jacob Southern (Anticipated graduation date: August 2016) Tentative Thesis Title: TBD MS: Taylor Barron (Anticipated graduation date: August 2016) Tentative Thesis Title: TBD MS: Colby Lewallen (Anticipated graduation date: August 2016) Tentative Thesis Title: TBD

Undergraduate Research Scholar Supervision Completed Jacob Southern (Fall 2014)

Senior Thesis Title: "On the Identification of Wear Parameters for HTHP Applications” Colby Lewallen (Fall 2013)

Senior Thesis Title: "Ceramic Seal Testing Apparatus Design” Franco Morelli (May 2012) Senior Thesis Title: "An investigation of Magneto Hydrodynamic Plasma Flows Inherent to

Tokamak Reactors and their impact on Plasma Density” Leland Ramson (May 2012) Senior Thesis Title: "An Investigation on Nonlinear Manufacturing Process Control in

Joint Time-Frequency Domains” In Progress Christian DeBuys (Spring 2015)

Senior Thesis Title: TBD Zachary Branigan (Spring 2015)

Senior Thesis Title: TBD


Selected Funded Research and Design Projects (2000-2014)

External Projects

1. Title: "Modular Rotary System for Long Duration DOE Test of Ceramic Seals" Sponsor: Schlumberger SPC Award: $75,000

Duration: 1/1/2015– 12/31/2016 2. Title: "Enhanced Rotary Apparatus for Improved Polymer Seal Testing and

Performance Evaluation" Sponsor: Schlumberger SPC Award: $75,000

Duration: 1/1/2015– 12/31/2016 3. Title: "Improvement of Rotary Ceramic Seal Apparatus"

Sponsor: Schlumberger SPC Award: $70,000

Duration: 6/1/2014– 5/31/2016 4. Title: "Characterization of Rotary Ceramic Sealing Configurations"

Sponsor: Schlumberger SRC Award: $40,000

Duration: 11/1/2013– 2/28/2014 5. Title: "Feasibility Study of Zero Leak, Water-Glycol, Solenoid Operated Valve"

Sponsor: Schlumberger SRC Award: $26,587 Duration: 12/1/2013 – 3/31/2014

6. Title: "Establish an Intelligent Equipment Lab for Precision Agriculture at PVAMU"

Sponsor: USDA – National Institute of Food and Agriculture (NIFA) PI: Suxia Cui, Co-PI: C. Steve Suh Sub-Award: $30,000 Duration: 9/1/2012 – 8/31/2015

7. Title: "Comparison and Gap Analyses for Sequence Valves" Sponsor: Schlumberger SRC Award: $12,000 Duration: 10/1/2012 – 1/31/2013

8. Title: "Shape Charge Improvement I, II, and III" Sponsor: Schlumberger SRC Award: $36,000 Duration: 9/1/2010 – 5/31/2012

9. Title: "HTHP Polymeric Material Characterizer"

Sponsor: Schlumberger SRC Award: $20,000 Duration: 9/1/2010 – 5/31/2012


10. Title: "Doghouse Cover" Sponsor: Trelleborg Offshore Award: $12,000 Duration: 9/1/2010 – 5/31/2011

11. Title: "Mechanical Clamp for Buoy"

Sponsor: Trelleborg Offshore Award: $12,000 Duration: 9/1/2011 – 5/31/2012

12. Title: "Wellhead Gate Valve Fire Override" Sponsor: Cameron Award: $12,000 Duration: 9/1/2010 – 5/31/2011

13. Title: "Wellhead Valve Spring Elimination"

Sponsor: Cameron Award: $12,000 Duration: 9/1/2010 – 5/31/2011

14. Title: "Emergency Power Back Up Battery" Sponsor: Cameron Award: $12,000 Duration: 9/1/2011 – 5/31/2012

15. Title: "Optimal Low Cost Insulated Beverage Dispenser Design Using Multinozzle

Structural-Web Molding Technology: Phase II" Co-PI: H.J. Sue Sponsor: Defense Logistics Agency, US DoD Award: $140,000 Duration: 4/1/2009 – 5/31/2010

16. Title: "Piezoelectric Flow Meter for Downhole Applications"

Sponsor: Schlumberger – Rosharon Award: $30,000 Duration: 8/31/2008 – 9/1/2009

17. Title: "Optimal Low Cost Insulated Beverage Dispenser Design Using Multinozzle

Structural-Web Molding Technology: Phase I" Co-PI: H.J. Sue Sponsor: Defense Logistics Agency, US DoD Award: $250,000 Duration: 8/1/2007 – 9/31/2008

18. Title: "Manufacturing Support for Seal and Curved Flapper Valve Designs"

Sponsor: Schlumberger – Rosharon Award: $25,000

19. Title: "BCTC Development"



20. Title: "Metal To Metal Seal Design" Sponsor: Schlumberger – Rosharon Award: $7,000

21. Title: "Flapper Valve with Frangible Curved Flapper" Sponsor: Schlumberger – Rosharon Award: $7,000

22. Title: "Study of High Performance Dynamic Seal for Down-hole Applications"


23. Title: "In-Flight Opening Door Uplock Assembly Design"

Sponsor: Lockheed Martin Aeronautics Award: $7,000

24. Title: "MWD Pulse Tool Test Apparatus"

Sponsor: Schlumberger – Sugar Land Award: $7,000

25. Title: "Integrated Metal Forming and Soldering"

Sponsor: Schlumberger – Sugar Land Award: $7,000

26. Title: "Hydraulic Tubing Optimization"

Sponsor: Schlumberger - Rosharon Award: $7,000

27. Title: "Non-Contact Interface For High Transmission Efficiency"

Sponsor: Schlumberger – Sugar Land Award: $7,000 Award Date: 9/1/2006

28. Title: "Labyrinth Protector"

Sponsor: Schlumberger – Rosharon Award: $7,000 Award Date: 9/1/2006

29. Title: "Application of Dual Gradient Technology To Top Hole Drilling"

Co-PI: Jerome Schubert Sponsor: MMS Award: $80,000 Duration: 9/1/2005 – 8/31/2006

30. Title: "Snow Globe"

Sponsor: Applied Materials Award: $7,500 Award Date: 9/1/2005

31. Title: "Laser-Induced Ultrasound Thermometry for Silicon Wafer Annealing"

Co-PI: Ravi Chona Sponsor: Texas Higher Education Coordinating Board (Advanced Research Program)


Award: $191,856 Matching: $28,800 Duration: 1/1/2002 – 12/31/2003

32. Title: “Guided Ultrasonic Waves in Semiconductor Materials” Co-PI: Ravi Chona Sponsor: National Science Foundation (NSF) Sensor Initiative Award: $209,871

Matching: $31,200 Duration: 9/15/2000 – 8/31/2003.

33. Title: "Centura Wafer Fabrication and Rapid Thermal Processing Facility"

(Equipment Donation) Sponsor: Applied Materials – Santa Clara RTP Division/Mr. John Piskator Award: $1,200,000 – estimated by Applied Materials.

34. Title: "Subsurface Defect Detection in Shelled Rail by TAP-NDE Real-Time Inspection Technique"

Sponsor: AAR Transportation Technology Center Award: $45,000 Duration: 1/1/2003 – 12/31/2003

35. Title: "Optimal TAP-NDE for the Detection of Subsurface Defect in Rails"

Sponsor: AAR Transportation Technology Center Award: $45,000 Duration: 1/1/2002 – 12/31/2002

36. Title: "Development and Characterization of Non-Autoclave Processes for Composites" PI: Roger J. Morgan Co-PI: Dimitris Lagoudas, Sai Lau, H.-J. Sue, C.S. Suh, John Whitcomb, Sponsor: UNO R&T Foundation (Under NASA Contract NCC8-223) Award: $190,000 Duration: 9/1/2001 – 3/31/2002

37. Title: "Characterization of Rail Quality Using TAP-NDE: Stage 2 - System

Optimization" Sponsor: Association of American Railroads (AAR) Award: $30,000 Duration: 1/1/2001 – 12/31/2001

38. Title: "Basic Research in The Applicability of Adhesion Mechanical Joints" Sponsor: 3M Corp. Award: $10,000

39. Title: "Thermadrum" Sponsor: A&M Concrete Award: $5,000

40. Title: "SBS Injection System" Sponsor: URS Award: $7,000


41. Title: "Percussion Drillbit Design"

Sponsor: DrilTech Missions Award: $7,000

42. Title: "Design of A High Performance 3-Way Valve" Sponsor: Schlumberger Award: $5,000

43. Title: "Failure Mechanisms of High Rise Cylindrical Structures Subject to Low Speed Wind Load"

Sponsor: Fluor Daniel Award: $5,000

44. Title: "Characterization of Rail Quality Using TAP-NDE: Stage 1 - Feasibility Study"

Sponsor: Association of American Railroads (AAR) Award: $20,000 Duration: 7/1/2000 – 12/31/2000

Internal Projects

1. Title: "Designing A Wavelet-based Diagnostic Methodology for Real-Time Failure Detection and Fault Identification of Rotor-Dynamic Systems"

Co-PI: Andrew K. Chan Sponsor: Interdisciplinary Research Initiative (IRI) Program Award: $25,000 Duration: 5/19/1999 – 5/18/2000

2. Title: "Mango Slices Dryer Using Continuously-Feed Air Heated By Solar Energy"

Co-PI: Martin Eduardo Baltazar-Lopez Sponsor: CONACYT Award: $25,000 Duration: 9/1/2005– 8/31/2006

Professional Services

ASME, Member (1989) ASEE, Member (1997) SEM, Member (1992) Sigma Xi, Member (1997) ASME Technical Committee on Vibration and Sound, Member (2006-2009) ASME AMD Division Technical Committee on Dynamics and Control of Systems and Structures,

Member (2014-date)

Documents

CHII-DER STEVE SUH - TAMU College of Engineering · CHII-DER STEVE SUH -- January 2015 Page 5 of 21 Authorships 1. (Book) Suh, C.S. and Liu, M.-K., “Control of Cutting and Machining