Turn on the printer

1

2

WLANSTATUS

1

1

5 7

10 11

2

2 3

1

2

3

4

86

9

Select "Enabled".

Note・When the printer is in the save mode, leave the save mode before starting the connection.・The IP address of the printer is 10.128.146.100 to type into the device you are connecting to.・You need to enter a PIN code depending on the setting of the device to connect. In this case, enter the PIN code displayed on the control panel into the target device.

A device name is displayed.

Enable the Wi-Fi setting of a device to connect and select the printer as its destination. When the device is within the radio waves of this product, the [Wi-Fi Direct接続] screen automatically appears on the control panel of the printer.

Wi-Fi® Direct connection

Configure the required setting and press [Update].

Enable [Wi-Fi Direct Settings] if it is disabled.

Wi-Fi® Direct setting

This product is rebooted and the setting is updated.

Press [Update].

Save.

Select "WEP".

Save.

Select "WEP".

Save.

Enter the passphrase.Select the desired encryption type.

Configure the setting of [Encryption Settings...].

Press [Encryption Settings...].Select [Infrastructure] or [Ad-hoc] and press [Save].

Press [Communication Mode...].

□ Network name (SSID)

Press [SSID] and specify the network name.

Proceed to ⑤.

Press [Common Settings].

If [Wireless LAN Settings] is not displayed, return to Step 1 and check the connection to this product. Some printers are not compatible with this product.

Press [System Settings] > [Connectivity & Network Setup] > [Wireless LAN Settings].

Press [Tools].Enter the System Administration mode in your printer.To enter the System Administration mode, refer to the User Manual of your printer.

Step3　Configure the basic setting

When you select the WPA2-PSK-AES or Mixed mode (PSK)* encryption type, specify the passphrase in 8 to 63 single-byte alphanumeric characters (8 to 64 characters for hexadecimal number).*: When you select Mixed mode PSK, an available encryption type (among WPA-PSK-TKZP, WPA-PSK-AES, or WPA2-PSK-AES) is automatically selected.

Only when you select the WEP encryption type, select the WEP key for using in the wireless LAN environment.

Select the encryption type among No Encryption, WEP, WPA2-PSK-AES, and Mixed mode (PSK).

Select either Infrastructure mode or Ad-hoc mode.For the Ad-hoc mode, set up the communication channel.

Specify the name to identify the wireless LAN environment. You can enter up to 32 single-byte alphanumeric characters.

Passphrase

WEP key

Encryption type

Communication mode

Network name(SSID)

Step1　Check the setup information

Confirm LED is ON

When the POWER LED (at the top) turns ON, turn ON the printer.

AC adapter

Electrical outlet

Wireless LAN converter

Connect the AC adapter to this product, and the AC adapter's plug to an electrical outlet.

Network cable

Printer(Power OFF)

Wireless LAN converter

1-1) Turn on the printer.1-2) Check that [Ethernet - Rated Speed] on the printer is set to the default value ([Auto]) (as shown below).1-3) Turn off the printer.1-4) Use the provided network cable to connect this product to the printer. Do not connect other devices (hub, router, etc) to this product. Be sure to use the network cable and make one-to-one

Step2　Install Wireless LAN converter

indicates the band available in IEEE802.11a/n.

Uses entire band range while blocking the bands of the "private radio station", "specified low power radio station" and "amateur radio station".

40 m or less

DS-SS type / OFDM type

2.4 GHz band

Change of frequency

Assumed interference distance

Transmission type

Using frequency band

means the following.

Turns ON when this product is powered on.ON: Running in Infrastructure modeOFF: Running in Ad hoc mode.BLINK: Processing setup using WPS feature.* Blinks together with STATUS LED when running in Configuration mode.* Only when Wi-Fi Direct connection starts, the lamp repeats lightning and blinking twice.ON: A network connection is established.BLINK: Transferring data* Blinks together with WLAN LED when running in Configuration mode.The Ethernet address for the LAN port of this product.The last 6 digits are the product's serial number. Example) If the Ethernet address is 00:80:92:00:11:22 (noted as 008092001122), then the product's serial number is 001122.

POWER LED (Orange)WLAN LED (Green)

STATUS LED (Green)

Ethernet address

Wireless standard mark

【Bottom】【Top】

Starts this product in Configuration Mode: Press and hold the push switch for 5 sec while this product is active.Configures this product using WPS function: Press and hold the push switch for 10 sec while this product is active.Resets this product to factory default settings: Press and hold the push switch while turning on this product. Release the switch when the Link LED on the LAN port turns to orange and then green.BLINK: Waiting for connection when Link LED is OFF. Transferring data when Link LED is ON.Connects to the network cable.ON (Green): Connected to 10BASE-T/100BASE-TX networkON (Orange): Connected to 1000BASE-T networkConnect AC adapter.

Push switch

Status LED (Yellow)

LAN portLink LED (Green/Orange)

Power connector

【Back】【Front】

Parts and function

□ Wireless LAN converter□ AC adapter□ Network cable□ Setup Guide (this document)

Following items are bundled in this product.

Package contents

Author/Publisher: Fuji Xerox Co., Ltd.Jun 2015 DE5921E2-1 (Edition 1)Copyright © 2015 by Fuji Xerox Co., Ltd.Printed in Japan

Thank you for purchasing Wireless LAN Converter (hereinafter "This product").

Before using this product, be sure to read "Safety Notes" in the User Guide of this

product and a printer connecting to this product for safety use.

This product is the wireless LAN converter which adds a wireless feature to our

printers that are compatible with the wire LAN communication and this

product. Also, wireless security feature of this product will allow secure use of

your network devices.This Setup Guide explains how to setup and use this product in a wireless network.

Wireless LAN ConverterSetup Guide

・To set the encryption type to Mixed mode (Enterprise): Proceed to "Set the encryption type to Mixed mode (Enterprise) through a Web browser on the PC" on the back of this guide.・To set the encryption type manually: Proceed to "Step2 Install Wireless LAN converter".・To set the encryption type automatically (WPS): Proceed to "Configure the network using

WPS" on the back of this guide.

Enter the System Administration mode and proceed to [Tools] > [System Settings] > [Connectivity & Network Setup] > [Protocol Settings] > [Ethernet Settings]. Check that [Ethernet - Rated Speed] is set to [Auto].

Start the Wi-Fi® Direct connection to connect your device to the printer after completing administrator settings (See the section below).

Select [Yes] for connection.

Proceed to "Wi-Fi® Direct setting".

Select a communicationmode.

Enter the network name (SSID).

If you select [Infrastructure] in ⑦

If you select [Ad-hoc] in ⑦

Select an encryption type.

If you select WPA2-PSK-AES or Mixed mode (PSK)

If you select WEP

Proceed to ⑩.

Proceed to ⑩.Register a WEP key. Press the button to display the keyboard and enter a WEP key.

It may take a few minutes to complete the update.

Select the desired transmission key.

604P 07311

fujixerox

1

5

2

6

1 2

WLAN

STATUS

1

3

2

4

3

4

1 2 4

5

6

3

1

2

Configure the required setting in a screen appeared.

Click [System Configuration] > [Wireless LAN Configuration] from the index on the left side of the screen, and click [Detailed Configuration].

Start a Web browser (Internet Explorer, Safari, etc) on the PC you are using for the setup. The Web page of this product is displayed.If the web page is not displayed, enter "fujixerox" in the address bar of the Web browser and press the Enter key.

Confirm LEDs are blinking

Release the push switch.

Push switch

Keep holding

Push switch

Confirm LED is ON

AC adapter

Electrical outletWireless LAN converter

Connect the AC adapter to this product, and the AC adapter's plug to an electrical outlet.

Network cable

PCWireless LAN converter

Use the provided network cable to connect this product to the PC.

Set the encryption type to Mixed mode (Enterprise) through a Web browser on the PC

Press the push button on the device to connect to in two minutes after pressing [Start].Press [WPS Settings (Push Button)].

With WPS-PBC (Wi-Fi Protected Setup-Push Button Configuration), you can authenticate and register the device required for wireless LAN settings by enabling the WPS-PBC setting on the control panel of the printer.

WPS-PBC

Confirm that the WPS settinxxxg is complete and press [Close].

� Enter the PIN code.

Press [Start] and enter [PIN code] on the control panel into the device to connect within 2 minutes.

Press [WPS Settings (PIN Code)].

Press [System Settings] > [Connectivity & Network Setup] > [Wireless LAN Settings].

Press [Tools].Enter the System Administration mode in your printer.To enter the System Administration mode, refer to the User Manual of your printer.

Set the PIN code allocated to the printer.□ PIN code

With WPS-PIN (Wi-Fi Protected SetupTM-Personal Identification Number), you can authenticate and register the device you want to add a wireless LAN feature by entering the PIN code allocated to the wireless LAN converter. For more information, please contact your network administrator.

WPS-PIN

NOTE- To perform the wireless configuration using WPS, your wireless router must support WPS. Please make sure that a wireless router supporting WPS is set up in your environment.- While performing this configuration, please temporarily move this product closer to your wireless router to make it easier for both devices to communicate.- Depending on your wireless router, WPS may need to be enabled manually. For details, refer to the operation manual that came with your wireless router.

Configure the network using WPS

Wireless Bridge SX-BR-4600WAN Specifications

Temperature : +0 C to +40 C , +32 F to +104 FHumidity : 20% to 80%RH (Non-condensing)Temperature : -10 C to +50 C , +14 F to +122 FHumidity : 20% to 90%RH (Non-condensing)VCCI Class B / FCC Class B / ICES Class B / EN55022 / EN5502410BASE-T/100BASE-TX /1000BASE-T (Auto-sensing) x 1 portAuto MDI/MDIXIEEE802.11 a/b/g/n (2Tx2R)(For channels you can use, check the regulations in your country.)1Top

LAN port

Network devices with a network port (RJ-45) on themSingle Client Mode: 1 device

POWER (Orange)WLAN (Green)STATUS (Green)

Status (Yellow)Link (Green/Orange)

Safety instructions

To ensure safe and proper use, please read the following information carefully before using this product. The safety instructions include important information on safe handling of the product and on general safety issues. Cautions regarding the device connected to this product are also included.

"Danger" indicates the existence of a hazard that could result in bodily injury if the safety instruction is not observed.- Do not allow physical impact: When damaged, unplug this product and the device from power and contact

your point of purchase. Failure to take this action could cause fire or an electrical shock.- If this product becomes hot, or you smell smoke, turn off the device, disconnect the power plug from this

product, and then unplug the power cable from electric outlet immediately. If a foreign object (liquid, metal) gets into this product, turn off the device, disconnect the power plug, and then unplug the power cable from electric outlet immediately.

- Failure to take this action could cause fire or an electrical shock.- Contact your point of purchase about repairing this product.

- Keep the cord and cables away from children. They may be injured or receive a shock.- If the device has a ground wire, it must be used to prevent electrocution and power surges.- Do not disassemble or modify this product. Contact your point of purchase about repairing this product.- Do not disassemble or alter the AC adapter bundled with the product.

"Warning" indicates the existence of a hazard that could result in material damage if the safety instruction is not observed.- When unplugging this product or a device, do not pull on the cord. The cord may break resulting in fire and/or

electric shock. Pull only on the plug.- When moving this product, disconnect the power and device cables. Fire or electric shock may occur.- Always use the AC adapter bundled with this product. Other AC adapters may cause this product to

malfunction.- Verify all cables are properly and safely before using this product.- When the product will not be used for an extended time, disconnect and unplug the power cable.- Do not allow physical impact: When damaged, unplug this product and the device from power and contact

your point of purchase. Failure to take this action could cause fire or an electrical shock.- Do not use or store this product under the following conditions to avoid potential damage to this product. [Prohibited]

- Hard vibrations- Tilted or unstable places- Exposure to the direct rays of the sun- Humid or dusty places- Wet place (kitchen or bathroom)- Heated places (near stove or heater)- Wide temperature change- Strong electromagnetic field (near magnet, radio or wireless device)

Safety instructions regarding the radio waves

- Do not use this product near medical devices such as a heart pacemaker. The radio wave generated by this product may interfere with the operation of these devices and may threaten one's life.

- Do not use this product near microwave ovens. The radio wave used by microwave ovens may cause interference to this product.

This product uses a 2.4GHz band. This band of equipment is used by a microwave, industry, science, medical equipment and licensed in room or low power (non licensed) radio stations.

1. Before you use this equipment, verify that it will not interfere with other broadcasting.2. If interference happens, stop using the equipment or change the band. Contact us to discuss ways of

avoiding interference (example: create the wall).

Please note the following instructions:

Notes on Security

Because a wireless LAN uses electromagnetic signals instead of a network cable to establish communication with network devices, it has the advantage of allowing devices to connect to the network easily. However, a disadvantage of this is that within a certain range, the electromagnetic signals can pass through barriers such as walls, and if security countermeasures are not implemented in some way, problems such as the following may occur.

- Communication is intercepted by a third party- Unauthorized access to the network- Leakage of personal information (ID and Card information)- Spoofing and the falsification of intercepted data- System crashes and data corruption

Nowadays, wireless LAN cards or access points are equipped with security measures that address such security problems, so that you can enable security-related settings for wireless LAN products in order to reduce the likelihood of problems occurring. We recommend that you make yourself fully acquainted with the possible implications of what might happen if you use a wireless product without enabling security features, and that you configure security-related settings and use wireless products at your own responsibility.

Operating environment

Storage environment

EMIWired network interface

Wireless network interface

Push SwitchLED

Supported devicesMax number of devices that can be connected

Notes on wireless devices using 2.4GHz band:

Notes on using 5GHz band:This product uses a 5GHz band. This product does not support Ad hoc mode when it is running in 5GHz band. - Wi-Fi and the Wi-Fi CERTIFIED logo are registered trademarks of the Wi-Fi Alliance.

- Wi-Fi Protected Setup and the Wi-Fi Protected Setup logo are trademarks of the Wi-Fi Alliance.- Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and other countries.

- Macintosh, Mac OS, and Safari are trademarks of Apple Inc registered in the United States and other countries.

- All other company and product names are registered trademarks and/or trademarks of their respective owners.

Trademarks

Even when you use this product properly, some radio wave condition sometimes causes interference to radio or television reception.In this case, pay attention to the following points:

- Does this product keep away from a radio and a television?- Is another electrical outlet used for this product and a radio and a television?

Voluntary Control of EMIThis equipment is classified as Class-B ITE. Although this equipment is subject to be used in a domestic environment, radio interference may occur when there is a radio or television receiver near the equipment. Use this equipment properly according to the instruction manual.

VCCI-B

Follow the above steps ① - ③ for WPS-PIN to display this screen.

Confirm that the WPxxxxxxS setting is complete and press [Close].3

If the wireless connection setting fails, a message appears on the control panel of the printer. Check NOTE above and return to step 1.

If the wireless connection setting fails, a message appears on the control panel of the printer. Check NOTE above and return to step 4.

Install a wireless LAN converter.(See "Step2 Install Wireless LAN converter".)

7