Upload
silvester-joseph
View
216
Download
1
Tags:
Embed Size (px)
Citation preview
CHAPTER 4
ENVIRONMENTAL FATE
This chapter serves as a basis to identify the hazards associated with different substances used and produced in the chemical process, including raw
materials, products and or byproducts.
It would then be possible to do follow up with an exposure assessment and a dose-response
assessment which are needed to perform risk characterization
Introduction
Substance Classification TreeWhat Substances?
Physical + ChemicalProperties
Old AnalysesEstimating Exposure
AndEnvironmental Effects
Classifying the Substances based on risk
Performing P2 on thesubstances...
Chemical Properties Used to Perform Environmental Risk Screenings
Environmental Process Relevant Properties
Dispersion and Fate Volatility, density, melting point, water solubility, effectiveness of waste, water treatment.
Persistence in the Environment
Atmospheric oxidation rate, aqueous hydrolysis rate, photolysis rate, rate of microbial degradation, and adsorption.
Continued on the following slide
Environmental Process Relevant Properties
Uptake by Organisms Volatility, Lipophilicity, Molecular Size, Degradation Rate in Organism.
Human Uptake Transport Across Dermal Layers, Transport Rates Across Lung Membrane, Degradation Rates within the Human Body.
Toxicity and other Health Effects
Dose-Response Relationships.
Chemical Properties Used to Perform Environmental Risk Screenings
• Distinguishes gas and liquid partitioning• Using the substance’s structure, it can be estimated by :
Where:
Tb: normal boiling point (at 1 atm) (K)
ni : number of groups of type i in the molecule,
gi : contribution of each functional group to the boiling point
Corrected using :
Tb (corrected) = Tb – 94.84 + 0.5577*Tb + 0.0007705*(Tb)2 (Tb 700K) (4.2)
Tb (corrected) = Tb + 282.7 – 0.5209*Tb (Tb > 700K) (4.3)
Tb= 198.2 + Σ nigi (4.1)
Boiling Point
Example : Boiling Point Estimation
Estimate the Normal Boiling Point for diethyl ether.
Diethyl ether has the molecular structure CH3-CH2-O-CH2-CH3
Group-O-
2(-CH3)2(-CH2)
gi contribution25.16
2(21.98)2(24.22)
Solving :
The actual boiling point for diethyl ether is 307.65 K
a) Using equation 4.1 : Tb (K)= 198.2 + Σ nigi
Tb (K)= 198.2 + 2(21.98) + 2(24.22) + 25.16
Tb = 315.76
b) Using equation 4.2 : Tb (corrected) = Tb – 94.84 + 0.5577*Tb - 0.0007705*(Tb)2
Tb (corr) = 315.76 – 94.84 + 0.5577(315.76) - 0.0007705(315.76)2
Tb (corrected) = 320.2 K
Example : Boiling Point Estimation (Continued)
Melting Point
• Distinguishes solid and liquid partitioning.• Can be estimated using the substance’s boiling point :
Where :
Tm : Melting Point in Kelvins.
Tb : Boiling Point in Kelvins.
(4.4)Tm (K) = 0.5839 * Tb (K)
Example : Melting Point Estimation
Estimate the Melting Point for diethyl ether.
Solving :
Using equation 4.4 to calculate the Tm :
Tm (K) = 0.5839 * Tb (K)
Tm (K) = 0.5839 * 307.65 K
Tm = 179.634 K
Vapor Pressure• Higher Vapor Pressure = Higher Air Concentrations• Can be estimated using the following equations :
ln Pvp = A + B/(T - C) (4.5)
Where : T = Tb at 1 atm
ln(1 atm) = 0 = A + B/(Tb – C) (4.6)
ln Pvp(atm) ={[A(Tb – C)2] / [0.97*R*Tb]}*{1/(Tb – C)-1/(T – C)}(4.7)
the parameters A and C can be estimated using : C = -18 + 0.19 Tb (4.7a)A = KF*(8.75+ R ln Tb) (4.7b)
Where : Pvp : vaporization pressure (atm).
T : absolute temperature and Tb is the boiling point at 1 atm.
A and C are empirical constants.B : a parameter related to the heat of vaporization.KF : a correction factor.
R : gas constant ; 1.987 L-atm K-1 mol-1
Tm : melting point (K).
For solids :
ln P = -(4.4 + lnTb) * {1.803*[(Tb/T)- 1)] - [0.803*ln (Tb/T)]} - 6.8(Tm/T-1) (4.8)
Vapor Pressure (continued)
Example : Vapor Pressure EstimationEstimate the Vapor Pressure for diethyl ether
Using the predicted value of 315.76 K:
C = -18 + 0.19Tb = -18 + 0.19(320.2) = 41.9944A = Kf (8.75 + R ln Tb) = 1.06 [8.75 + 1.987 ln(320.2)] = 21.3962
ln Pvp = {[A(Tb – C)2] / [0.97*R*Tb]}*{1/(Tb – C) - 1/(T – C)}
= {[21.39(315.76-41.99)2] / [0.97(1.987)(315.76)]}*{1/(273.76) – 1/(256)}
Ln Pvp = -0.6677; Pvp = 0.5128 atm = 389.79 mm Hg.
(4.7.a)(4.7.b)
(4.7)
Repeating the calculation for the experimental boiling point leads to a vapor pressure estimated of Pvp = 0.6974 atm = 530.06 mm Hg.
Octanol-Water Partition Coefficient• Describes partition between an aqueous phase and it’s suspended organic phases.• Can be estimated using the substance’s structure :
log Kow = 0.229 + Σ nifi (4.9)
log Kow (corrected) = 0.229 + Σ nifi + Σ njcj (4.10)
Where: Kow : Octanol-Water Partition Coefficient.
ni : number of groups i in the compound.fi : factor associated with the group i nj : number of groups j in the compound that have correction factors. cj : correction factor for each group j
Example : Octanol-Water Partition Coefficient Estimation
Estimate the Octanol-Water Partition Coefficient for diethyl ether.
Solving :
Using equation 4.9 : log Kow = 0.229 + Σ nifi
log Kow = 0.229 + 2(0.5473) + 2(0.4911) + (1.2566)
log Kow = 1.0492 ≈ 1.05 therefore Kow = 11.2
Group-O-
2(-CH3)2(-CH2)
fi contribution-1.2566
2(0.5473)2(0.4911)
Bioconcentration Factor• Describes partitioning between aqueous and lipid phases
in living organisms.• Higher bioconcentration factors = higher quantity of bioaccumulation in living organisms• Can be calculated using :
log BCF = 0.79*(log Kow) – 0.40 (4.11)
log BCF = 0.77*(log Kow) – 0.70 + Σ jj (4.12)
Where :BCF : Bioconcentration Factor.Kow : octanol-water partition coefficient.jj : correction factor for each group.
Example : Bioconcentration Factor (BCF) Estimation
Estimate the Bioconcentration Factor for diethyl ether.
Solving : Using equation 4.9 we obtain log Kow :
log Kow = 0.229 + Σ nifi log Kow = 1.0492 ≈ 1.05
Using equation 4.11 we can calculate BCF :log BCF = 0.79*(log Kow) – 0.40 log BCF = 0.79* (1.05) – 0.40 log BCF = 0.4295therfore BCF = 2.6884
Water Solubility• Used to assess concentrations in water• Can be calculated using :
Log S = 0.342 – 1.0374 logKow – 0.0108 (Tm –25) + Σhj (4.13)
Log S = 0.796 –0.854 logKow – 0.00728 (MW) + Σhj (4.14)
Log S = 0.693 – 0.96 los Kow – 0.0092 (Tm –25) – 0.00314 (MW) + Σhj (4.15)
Where :
S : water solubility (mol/L).Kow : octanol-water partition coefficient.Tm : melting point (ªC).MW :s the molecular weight of the substance. hj is the correction factor for each functional group j.
Example : Water Solubility EstimationEstimate the Water Solubility for diethyl ether.
Solving :
Equation 4.9 gives the log Kow ≈ 1.05
Using equation 4.14 we can calculate the S :Log S = 0.796 –0.854 logKow – 0.00728 (MW) + Σhj Log S = 0.796 – 0.854(1.05) – 0.00728(74.12) + 0.0Log S = -0.6403
Therfore : S = 0.2289 mol/L. = 16.966 g/L = 16,966.068 mg/ L
Henry’s Law Constant
• Describes the affinity for air over water.• Can be determined using :
-log H = log (air-water partition coeff) = Σ nihi + Σ njcj (4.19)
Where : H : dimensionless Henry’s Law Constant.ni : number of bonds of type i in the compound.hi : bond contribution to the air-water partition coefficient.nj : number of groups of type j in the molecule.cj : correction factor for each group.
Example : Henry’s Law Constant Estimation
Estimate the Henry’s Law Constant for diethyl ether. H H H H
H-C-C-O-C-C-H H H H H
Expressed as a collection of bonds, diethyl ether consists of 10 C-H, 2 C-C bonds, and 2 C-O bonds. The uncorrected value of log (air to water partition constant) is given by :
-log H = log (air-water partition coefficient) =
10(-0.1197) + 2(0.1163) + 2(1.0855) = 1.2066
log H-1 = 1.2066
Soil Sorption Coefficient• Used to describe the Soil-Water Partitioning.• Can be estimated by :
log Koc = 0.544 (log Kow) +1.377 (4.16)
log Koc = -0.55 (log S) + 3.64 (4.17)
log Koc = 0.53 1χ + 0.62 + Σ njPj (4.18)Where :
Koc : Soil Sorption Coefficient (μg/g of organic carbon (to μg/mL of
liquid)).Kow : Octanol-Water Partition Coefficient.S : Water Solubility.1χ : first order Molecular Connectivity Index (from literature-appendix ).nj : number of groups of type j in the compound.Pj : correction factor for each group j.
The first step in calculating 1χ is to draw the bond structure of the molecule. For example, isopentane would be drawn as:
CH3
H3C-CH-CH2-CH3
The second step is to count the number of carbon atoms to which each carbon is attached. Each C-C bond is given a value of 1 and δi, is the parameter that defines the quantity of carbon atoms connected to a carbon atom i. The diagram below gives the δi, values for the different carbon atoms.
CH3
H3C-CH-CH2-CH3
(1)
(1)
(1)(3) (2)
Molecular Connectivity Index Calculations
The third step is to identify the “connectedness” of the carbons connected by the bond (δi , δj). For isopentane, these pairs are:
The value of 1χ can then be calculated using the equation :
1χ = Σ(δi* δj)-0.5 (4.19)
For isopentane, 1χ = (1/√3) + (1/√3) + (1/√6) + (1/√2) = 2.68
CH3
H3C-CH-CH2-CH3
(2,1)
(1,3) (3,2)
Molecular Connectivity Index Calculations (continued)
(1,3)
Example : Soil Sorption Coefficient Estimation
Estimate the Soil Sorption Coefficient for diethyl ether.
Solution : The molecular structure for diethyl ether is :
CH3-CH2-O-CH2-CH3
Using previously calculated values for log Kow (estimated at 1.0492) and log S (estimated at -0.6384) we can estimate the soil sorption coefficients using equations 4.16 and 4.17 :
log Koc = 0.544 (log Kow) + 1.377 = 1.9482
log Koc = -0.55 (log S) + 3.64 = 3.99
Using the molecular connectivity we can also estimate the soil sorption coefficient :
First the molecular connectivity index is calculated using eq. 4.19 :CH3-CH2-O-CH2-CH3 (molecular structure)2(C-C), 2(C-O), 2(1, 2) , 2(2, 2) (connection pairs)
therefore : 1χ = 2(1/√2) + 2(1/√4) = 2.414
Using equation 4.18 to calculate the soil sorption coefficient :
log Koc = 0.53 1χ + 0.62 + Σ njPj
log Koc = 0.53 1χ + 0.62 + Σ njPj = 0.53(2.414) + 0.62 + (-1.264)
log Koc = 0.63542
therefore : Koc = 4.32
Example : Soil Sorption Coefficient Estimation
Where to look up this information...
http://www.chem.duke.edu/~chemlib/properties.html
http://www.library.vanderbilt.edu/science/property.htm
http://www.library.yale.edu/science/help/chemphys.html
What do the different Properties mean?
Adapted from the Green Engineering Textbook
Estimating Environmental Persistence and Ecosystem Risks
To be discussed :
– Atmospheric Lifetimes
– Aquatic Lifetimes
– Overall Biodegradability
– Ecosystems
Estimating Atmospheric Lifetimes• One way to estimate the atmospheric lifetime of a
compound is to analyze the rate of oxidation of the substance, specifically the hydroxyl radical reaction rate.
• Group contributions is again one of the approaches that can be taken to estimate this property.
• Using examples, we will show how to estimate reaction rates and half lives while using the appropriate correction factors.
Example : Atmospheric Lifetime Estimation
Dimethylsulfide (DMS, CH3SCH3) produced by phytoplankton degredation is thought to be the major source of the sulfate and methanesulfonate aerosol found in the marine boundary layer.
The primary objective of this research effort is to determine the detailed mechanism of, and final product yields from, the OH initiated gas phase oxidation of DMS.
At the low NOx levels that are characteristic of the remote marine boundary layer, reaction with OH is the initial step in DMS oxidation.
OH + CH3SCH3 Products (1)⇒
The OH initiated oxidation of DMS proceeds via a complex, two channel, mechanism involving abstraction (1a) and reversible addition (1b, -1b). This can be described by the reaction sequence:
CH3SCH3 + OH CH⇒ 3SCH2 + H2O (1a)
CH3SCH3 + OH + M ⇔ CH3S(OH)CH3 + M (1b, -1b)
CH3S(OH)CH3 + O2 Products (3)⇒
Because of this complex mechanism the effective rate coefficients for reaction (1) and its deuterated analog, reaction (2) depend on the partial pressure of O2 at any total pressure.
OH + CD3SCD3 Products (2)⇒
The two channel reaction mechanism implies that in the absence of O2 we measure k1a, the abstraction rate. As we add O2 the effective rate increases until we measure a limiting rate (k1a + k1b).
Estimating Aquatic Lifetimes• One way to estimate the aquatic lifetime of a compound is to analyze the rate of hydrolysis of the substance.• The rate of hydrolysis can be estimated by :
log (hydrolysis rate) = log (hydrolysis rate of a reference compound) + Constant * σ
Therefore log (hydrolysis rate) = A + Bσ (4.20)
Where : A is rxn and compound class specific(depends on the reference rxn chosen) B is rxn and compound class specific (depends on type of rxn considered)σ is a structural parameter commonly used in linear free energy relationship.
Estimating Overall Biodegradability
• It is difficult to do an overall biodegradability analysis.• It can be estimated using :
Where : an is the contribution of the functional group (see table ).
fn is the number of different functional group.
MW is the molecular weight.
I is an indicator of aerobic biodegradation rate.
• Different Values (of I) represent different life times :
I = 3.199 + a1f1 + a2f2 + a3f3 +... + anfn + amMW(4.21)
I value 5 4 3 2 1
Expected degradation rate Hours Days Weeks Months Years
Example : Overall Biodegradability Estimation
Estimate the Biodegradation Index for diethyl ether.
Solution : Molecular weight of diethyl ether :MW = 74.12 g/mol
Using equation 4.21, the index can be calculated :I = 3.199 + a1f1 + a2f2 + a3f3 + ... + anfn + amMWI = 3.199 + (- 0.0087) - 0.00221(74.12) = 3.0267
Therefor a lifetime of WEEKS
Estimating Ecosystem RisksCompare the Fish, Guppy and Daphnids mortalities for an acrylate with log Kow = 1.22 (e.g. ethyl acrylate).
Guppies
log (1/LC50) = 0.871 log Kow – 4.87 (4.22)
log (1/LC50) = 0.871(1.22) – 4.87 = -3.80738LC50 = 6417.74 µmol/L.
Daphnids
log LC50 = 0.00886 – 0.51136 log Kow (4.23)
log LC50 = 0.00886 – 0.51136(1.22) = -0.6149992LC50 = 0.242 millimoles/L = 242 µmol/L.
Fish
log LC50 = -1.46 – 0.18 log Kow (4.24)
log LC50 = -1.46 – 0.18(1.22) = -1.6796LC50 = 0.021 millimoles/L = 21 µmol/L.
The concentrations yielding 50% mortality are:
Guppies (14 day): 6417.74 µmol/L.Daphnids (48 hour): 0.242 millimoles/L = 242 µmol/L.Fish (96 hour): 0.021 millimoles/L = 21 µmol/L.
Estimating Ecosystem Risks Continued
Environmental Fate and Exposures
Example : If chemicals are released into a river upstream of a water treament plant, what factors need to be taken into account to estimate the potential danger to the community. What fraction of the chemicals are:
- Absorbed by river sediments. - Volatilized into the air.- Taken up by living organisms. - Biodegraded.- Reacted with other compounds. - Removed in the
treatment process.
Classification of Substances Based on Risk
By examining the table XX, we can use the calculated properties to qualitatively quantify the risk associated with the different substances
Three main criteria are normally considered in the classification of the substances : persistence, bioaccumultion and toxicity.
There do not exist a given set of regulations or guidelines on quantifying risk, but the above parameters are used in the process.
Available Ressources
EPA (persistent, bioaccumulating and toxic substances) : http://www.epa.gov/pbt/aboutpbt.htm
http://www.epa.gov/opptintr/pbt/
Pollution Prevention, Waste Minimization and PBT Chemical Reduction :
http://yosemite.epa.gov/R10/OWCM.NSF/0d511e619f047e0d88256500005bec99/6ad9c10eb8a06bc288256506007def78?opendocument
Environment canada (existing substances evaluation) : http://www.ec.gc.ca/substances/ese/eng/psap/psap_2.cfm