38
Chapter 2: Sketching, Lettering, and Lines Sketching lines, circles, arcs and multiviews. Freehand lettering and mechanical lettering equipment.

Chapter 2: Sketching, Lettering, and Lines Sketching lines, circles, arcs and multiviews. Freehand lettering and mechanical lettering equipment

Embed Size (px)

Citation preview

Page 1: Chapter 2: Sketching, Lettering, and Lines Sketching lines, circles, arcs and multiviews. Freehand lettering and mechanical lettering equipment

Chapter 2: Sketching, Lettering, and Lines

Sketching lines, circles, arcs and multiviews. Freehand lettering

and mechanical lettering equipment.

Page 2: Chapter 2: Sketching, Lettering, and Lines Sketching lines, circles, arcs and multiviews. Freehand lettering and mechanical lettering equipment

Sketching is Freehand Drawing

• Advantages:– Fast visual

communicator

– Helps to organize thought

– Minimizes errors on final drawings

- Sketches help to record the stages of progress on a design

- Useful for of illustration

- Useful for laying out dimensions of a part

Page 3: Chapter 2: Sketching, Lettering, and Lines Sketching lines, circles, arcs and multiviews. Freehand lettering and mechanical lettering equipment

The Quality of a Sketch Depends On its Intended Purpose

Speed is the big key to sketching. A sketch is to be used to relate a design idea to someone

quickly.

Page 4: Chapter 2: Sketching, Lettering, and Lines Sketching lines, circles, arcs and multiviews. Freehand lettering and mechanical lettering equipment

Tools and Materials for Sketching

• Paper – newsprint or graph paper

• Pencil- common #2 pencil or automatic 0.7mm or 0.9mm pencil with F or HB lead

• Eraser

The best sketches are made when you can move the paper freely.

Page 5: Chapter 2: Sketching, Lettering, and Lines Sketching lines, circles, arcs and multiviews. Freehand lettering and mechanical lettering equipment

Sketching Straight Lines

• Lines should be sketched in short, light, connected segments.

• Sketch light lines when you are first laying out the sketch.

• Darken the lines when you are ready to finish the sketch.

• Very long lines can be sketched using the edge of the paper or table as a guide.

Page 6: Chapter 2: Sketching, Lettering, and Lines Sketching lines, circles, arcs and multiviews. Freehand lettering and mechanical lettering equipment

Steps to Sketch a Horizontal Straight Line

Step 1: Mark the starting and ending positions with points.

Step 2: Without touching the paper, sketch the direction of the line.

Step 3: Sketch light short strokes between points – keep your eye focused on the end point.

Step 4: Darken the final lines.

Page 7: Chapter 2: Sketching, Lettering, and Lines Sketching lines, circles, arcs and multiviews. Freehand lettering and mechanical lettering equipment

Sketching Circular Lines

• Quick Small Circles

• Box Method

• Centerline Method

• Hand-Compass Method

• Trammel Method

Page 8: Chapter 2: Sketching, Lettering, and Lines Sketching lines, circles, arcs and multiviews. Freehand lettering and mechanical lettering equipment

Sketching Quick Small Circles

These are easy to draw. It is just like drawing the letter “O.”

Page 9: Chapter 2: Sketching, Lettering, and Lines Sketching lines, circles, arcs and multiviews. Freehand lettering and mechanical lettering equipment

Parts of a Circle

Page 10: Chapter 2: Sketching, Lettering, and Lines Sketching lines, circles, arcs and multiviews. Freehand lettering and mechanical lettering equipment

Box Method for Sketching CirclesStep 1: Sketch a square equal to the diameter of the

circle using light lines.Step 2: Sketch diagonal lines across each corner of

the square.Step 3: Establish marks on the diagonal lines out

from the center of the square equal to the circle radius you want to sketch.

Step 4: Create the circle by sketching arcs that are tangent to the sides of the square and go through the marks on the diagonals.

Page 11: Chapter 2: Sketching, Lettering, and Lines Sketching lines, circles, arcs and multiviews. Freehand lettering and mechanical lettering equipment

Centerline Method for Sketching a Circle

Step 1: Sketch very light horizontal, vertical, 45 degree lines that meet at the center of the proposed circle.

Step 2: Mark the approximate radius of the circle on the centerlines.

Step 3: Create the circle by sketching arcs that go through the marks on the centerlines.

Page 12: Chapter 2: Sketching, Lettering, and Lines Sketching lines, circles, arcs and multiviews. Freehand lettering and mechanical lettering equipment

Hand-Compass Method for Sketching a Circle

Step 1: Allow the paper to free rotate 360 degrees.

Step 2: Use your index finger as the point of the compass. The pencil rests in your palm and makes contact with the paper as you pivot around your index finger. Control the pencil with your thumb.

Step 3: Determine the circle radius by adjusting the distance between your index finger and the pencil point.

Step 4: When drawing the circle, keep your hand and pencil point in one place, and rotate the paper with the other hand to create the circle.

Step 5: Darken the final circle.

Page 13: Chapter 2: Sketching, Lettering, and Lines Sketching lines, circles, arcs and multiviews. Freehand lettering and mechanical lettering equipment

Trammel Method to Sketch a Circle

Step 1: Create a trammel larger than the circle radius out of 1” wide paper. Mark the radius with tick marks.

Step 2: Sketch a straight line with tick marks (a & b) to locate the radius of the circle and the center of the circle.

Step 3: Place the paper trammel on the line, lining up the radius tic marks. Pivot the trammel about the center mark (b).Lightly make tic marks as you rotate the trammel.

Step 4: Solid in the tic marks to create the final circle.

Page 14: Chapter 2: Sketching, Lettering, and Lines Sketching lines, circles, arcs and multiviews. Freehand lettering and mechanical lettering equipment

Sketching Arcs• Technique is similar to sketching circles.

• Arcs are generally drawn with a radius.

• Sketch the arc with your hand facing the inside of the arc.

• An arc is part of a circle and forms rounded corners.

• The arcs creates a smooth connection at the point of tangency with the straight line.

Page 15: Chapter 2: Sketching, Lettering, and Lines Sketching lines, circles, arcs and multiviews. Freehand lettering and mechanical lettering equipment

Sketching Ellipses• An ellipse has a major diameter and a minor diameter.• To sketch an ellipse, create a box equal to the major

and minor diameter. • Now sketch lines from the corners to the mid point of

the major diameter lines of the box. From the cross points in the lines, use that radius for the end arcs of the ellipse. From the midpoints on the major diameter box lines, sketch an arc equal in radius to the sketch lines to the corners for the major arcs.

Page 16: Chapter 2: Sketching, Lettering, and Lines Sketching lines, circles, arcs and multiviews. Freehand lettering and mechanical lettering equipment

Measurement Lines and Proportions• All lines in a sketched object are related to

each other in size and direction.

• The first line in a sketch is the measurement line and sets the scale of the sketch.

• All other lines are sketched in relation to the first line.

• The same relationship can also be applied to spaces.

Page 17: Chapter 2: Sketching, Lettering, and Lines Sketching lines, circles, arcs and multiviews. Freehand lettering and mechanical lettering equipment

Block Technique in Sketching an Object

Step 1: Visualize the object surrounded by an overall rectangle using proper proportions.

Step 2: Using the lightly sketched rectangle, start sketching out areas of the object working from the edge of the rectangle.

Step 3: Measure from the rectangle edges to locate interior features.

Step 4: Darken final lines of sketched object.

Page 18: Chapter 2: Sketching, Lettering, and Lines Sketching lines, circles, arcs and multiviews. Freehand lettering and mechanical lettering equipment

Sketching Irregular Shapes

Step 1: Place the object in a lightly constructed box.

Step 2: Draw a grid of equally spaced horizontal and vertical lines.

Step 3: Establish a similar grid on the object you are transferring by sketch or visualize a grid on the real object.

Step 4: On the sketch, reestablish a proportioned grid similar to the one over the original drawing.

Step 5: Using the new grid, draw in the irregular object, placing the arcs and line in the same grid positions as the original drawing.

Step 6: Darken final sketch.

Page 19: Chapter 2: Sketching, Lettering, and Lines Sketching lines, circles, arcs and multiviews. Freehand lettering and mechanical lettering equipment

Creating Multiview Sketches

• Multiview projection is also known as orthographic projection.

• Multiviews are 2 dimensional views of a 3D object.

• Line of sight is perpendicular (90 degrees) to the surface of the object.

Page 20: Chapter 2: Sketching, Lettering, and Lines Sketching lines, circles, arcs and multiviews. Freehand lettering and mechanical lettering equipment

Multiview Alignment

• Sketch the front view first in the lower left portion of the paper.

• Place the top view directly above the front view and the right side view to the right side of the front view.

• The choice of views depends on the object to be drawn.

Page 21: Chapter 2: Sketching, Lettering, and Lines Sketching lines, circles, arcs and multiviews. Freehand lettering and mechanical lettering equipment

Establishing Isometric Axes

Step 1: Sketch a horizontal reference line (ground level).

Step 2: Sketch a vertical line perpendicular to the ground line. Use this line to measure heights.

Step 3: Sketch 30° angular lines starting at the intersection of the first two lines.

Page 22: Chapter 2: Sketching, Lettering, and Lines Sketching lines, circles, arcs and multiviews. Freehand lettering and mechanical lettering equipment

Making a Isometric Sketch

Step 1: Select the best view of the object.

Step 2: Set up isometric axes.

Step 3: Draw an isometric rectangle in proportion to the object.

Step 4: Lightly sketch in the features of the object.

Step 5: Darken in all of the object lines.

Page 23: Chapter 2: Sketching, Lettering, and Lines Sketching lines, circles, arcs and multiviews. Freehand lettering and mechanical lettering equipment

Placing Nonisometric Lines

Step 1: Develop a proportional box.

Step 2: Sketch all isometric lines.

Step 3: Locate the starting and ending points of nonisometric lines.

Step 4: Sketch in the nonisometric lines by connecting the points.

Page 24: Chapter 2: Sketching, Lettering, and Lines Sketching lines, circles, arcs and multiviews. Freehand lettering and mechanical lettering equipment

Four-Center Method for creating Isometric Circles

Step 1: Draw an isometric cube.

Step 2: On each surface of the cube, draw lines that connect the 120° corners to the centers of the opposite sides.

Step 3: Sketch arcs using the lines on each surface as the radius for arcs in the 120° corners.

Step 4: Sketch arcs using the intersection of where the lines cross on each surface to establish the radius for the smaller arcs.

Page 25: Chapter 2: Sketching, Lettering, and Lines Sketching lines, circles, arcs and multiviews. Freehand lettering and mechanical lettering equipment

Single Stroke Gothic Lettering

• Today this standard is conveyed by the American Society of Mechanical Engineers (ASME Y14.2, Line Conventions and Lettering).

• This is the standard for lettering established in 1935 by the American National Standards Institute (ANSI).

• Industry uses the upper case style as the standard.

Page 26: Chapter 2: Sketching, Lettering, and Lines Sketching lines, circles, arcs and multiviews. Freehand lettering and mechanical lettering equipment

Other Lettering Styles Used in Drafting

• Inclined Lettering

• Lowercase Lettering

• Architectural Style

Page 27: Chapter 2: Sketching, Lettering, and Lines Sketching lines, circles, arcs and multiviews. Freehand lettering and mechanical lettering equipment

Lettering Legibility

• ASME: Lettering size for dimensions numerals and notes - .125 in.(3mm) high

• ASME: Lettering size for titles, drawing numbers, section and view letters and captions - .25 in. (6mm) high

Page 28: Chapter 2: Sketching, Lettering, and Lines Sketching lines, circles, arcs and multiviews. Freehand lettering and mechanical lettering equipment

Lettering Legibility (continued)• Use only one style of lettering on a drawing.• Lettering should be dark, crisp & opaque.• Minimum space between letters - .06 in. (1.5mm)• The space between words in a sentence is the same as the height of

the letters.• The minimum space between 2 numerals with a decimal point is 2/3 the

letter height.• Notes should be lettered horizontally on a page.• Space between lines of letters is equal to the height of a letter.• Vertical or inclined letters may be used.

Page 29: Chapter 2: Sketching, Lettering, and Lines Sketching lines, circles, arcs and multiviews. Freehand lettering and mechanical lettering equipment

Vertical Freehand Lettering• Standard for mechanical drafting• Use lightly drawn horizontal guidelines.• Use 0.5 mm automatic pencil with H,F,or HB lead.• Each letter is composed of single strokes to make the

letter.• Fraction numerals are same size as other numerals.• The fraction bar is most often drawn horizontally. • The fraction numbers do not touch the fraction bar.• Decimal points should be dark and clear with enough

room around them to be clearly read.

Page 30: Chapter 2: Sketching, Lettering, and Lines Sketching lines, circles, arcs and multiviews. Freehand lettering and mechanical lettering equipment

Making Guidelines

• Guidelines are drawn to the height of the letters.

• Use hard lead such as 6H or 4H lead, or use non-photo blue lead.

• Use an Ames Lettering guide for assistance.

Page 31: Chapter 2: Sketching, Lettering, and Lines Sketching lines, circles, arcs and multiviews. Freehand lettering and mechanical lettering equipment

Lines

• All lines should be dark, crisp, sharp, and of correct thickness (ASME).

• ASME recommends two line thicknesses.

• Military standards require three line thicknesses: thick, medium & thin.

• Line standard relates to manual and computer-aided drafting.

• Thick lines – 0.6 mm• Thin lines – 0.3 mm

Page 32: Chapter 2: Sketching, Lettering, and Lines Sketching lines, circles, arcs and multiviews. Freehand lettering and mechanical lettering equipment

Line Conventions

Page 33: Chapter 2: Sketching, Lettering, and Lines Sketching lines, circles, arcs and multiviews. Freehand lettering and mechanical lettering equipment

Types of Lines• Construction and

Guidelines• Object Lines• Hidden Lines• Centerlines• Extension Lines• Dimension Lines &

Leader Lines

• Arrowheads• Cutting-Plane &

Viewing-Plane Lines• Section Lines• Break Lines• Phantom Lines• Chain Lines• Stitch Lines

Page 34: Chapter 2: Sketching, Lettering, and Lines Sketching lines, circles, arcs and multiviews. Freehand lettering and mechanical lettering equipment

Pencil Line Technique• All lines should be the same darkness.• Wash your hands & equipment often for a cleaner drawing.• Lay out the entire drawing in construction lines.• Draw horizontal thin lines first, then draw vertical thin lines.• Next, draw all circles and arcs.• Last, draw all horizontal and vertical thick lines.• Finish with all of the lettering and notes• Always draw radii first before straight lines – this makes for

a smoother transition.

Page 35: Chapter 2: Sketching, Lettering, and Lines Sketching lines, circles, arcs and multiviews. Freehand lettering and mechanical lettering equipment

Inking Technique• Use the correct side of the media with the inking surface.• Use template lifters to avoid smearing the ink.• Maintain a clean pen to avoid ink blots and poor line quality.• Make arcs first for ease of connecting to a straight line.• Follow the same procedure for laying ink lines as with pencil

lines (i.e. horizontal lines first, etc.).• Hold technical pens 90° to the surface for proper ink flow

and line definition – do not apply too much pressure.• Ink away from previous lines to avoid smearing.• Move the pen at a constant speed – do not decrease

movement at the end of a line.

Page 36: Chapter 2: Sketching, Lettering, and Lines Sketching lines, circles, arcs and multiviews. Freehand lettering and mechanical lettering equipment

Erasing Ink

• Electric erasers work well to erase ink on vellum in small areas.

• A smooth area will not take ink again.• To erase on polyester film use:

– Ink remover– Water on a cotton swab– Ink eraser

Page 37: Chapter 2: Sketching, Lettering, and Lines Sketching lines, circles, arcs and multiviews. Freehand lettering and mechanical lettering equipment

Pencil Skills with Polyester Lead

• Draw with a single line in one direction.

• Draft with a light touch.

• Draft over recommended backing material for a drafting board.

• Erase with the vinyl eraser. Use the electric eraser with care.

Page 38: Chapter 2: Sketching, Lettering, and Lines Sketching lines, circles, arcs and multiviews. Freehand lettering and mechanical lettering equipment

Web Site Research

• http://www.asme.org/asme/8.html

• http://www.ansi.org

• http://www.adda.org