Chapter 2:Drilling Hydraulics

Introduction One of the primary functions of drilling fluid is to carry

drilled cuttings from the bit face, up the annulus, between the drillstring and wellbore, to surface

A significant amount of power is required to overcome the (frictional) resistance to flow of the fluid in the drillstring, annulus and through the nozzlesin the bit.

The magnitude of the resistance to flow is dependant on a number of variables.

The resistance is expressed in terms of the amount of pressure required to circulate the fluid around the system and is therefore called the circulating pressure of the system.

sacrificial pressure losses:The pressure required to circulate the fluid through the drillstring and annulus are often called sacrificial pressure losses, they do not contribute anything to the drilling process

pressure losses through the nozzlesThe ejection of the fluid through the nozzles in the bit also results in significant pressure loss but does perform a useful function(it helps to clean the drilled cuttings from the face of the bit.

hydraulic horsepower (HHP) of the pumps

The product of the circulating pressure losses and the flowrate through the system is equal to the hydraulic power that the mud pumps will have to generate.

where,Pt = Total pressure (psi)Q = flow rate (gpm)

Since the flowrate through all parts of the system is equal, attention is generally focused on the pressure losses in each part of the system.

This expression for hydraulic horsepower is a general expression and can also be used to express the power which is expended in sacrificial losses and the power that is used to

pump the fluid through the nozzles of the bit.

Horsepower Used in Drillstring and Across Nozzles of Bit

The primary function of the drilling fluid is to carry the drilled cuttings to the surface. In order to do this the velocity of the fluid in the annulus will have to be high enough to ensure that the drilled cuttings are efficiently removed.

If these cuttings are not removed the drillstring will become stuck and theoretical optimization will be fruitless.

Considerations with respect to optimization should therefore only be addressed once the minimum annular velocity for which the cuttings will be removed is achieved.

Only then, should any further increase in fluid flowrate be used to improve the pressure loss across the nozzles of the bit and therefore the hydraulic power at the bit face.

Annular Velocity

• This minimum annular velocity is dependent on the properties of the mud and cuttings for any particular well, and is usually between 100 - 200 ft/min

Homework Assume a flow rate of 920 gpm in a 17.5-inch hole with 4.5-inch drill pipe.

What is the annular velocity (ft/min and ft/sec) of the mud?

TRANSPORT VELOCITY

• Transport or lift velocity is defined as the difference between the annular velocity of mud and the slip velocity of particle; ie

Vt = Va - Vs

whereVt = transport velocityVa = annular velocityDh = hole diameterODp = outside diameter of pipe

FLOW REGIME

Laminar Flow (Streamline or Viscous flow) : In this type of flow, layers of fluid move in streamlines or

laminae. There is no microscopic or macroscopic intermixing of the layers. Laminar flow systems are

generally represented graphically by streamlines. Turbulent Flow : In turbulent flow there is an irregular random movement

of fluid in a transverse direction to the main flow. This irregular, fluctuating motion can be regarded as

superimposed on the mean motion of the fluid.

FLOW REGIME Laminar flow: In laminar flow, fluid layers flow parallel to each other in an orderly fashion. This flow occurs at low to moderate shear rates when friction between the

fluid and the channel walls is at its lowest. This is a typical flow in the annulus of most wells.

Turbulent flow: This flow occurs at high shear rates where the fluid particle move in a

disorderly and chaotic manner and particles are pushed forward by current eddies. Friction

between the fluid and the channel walls is highest for this type of flow. This is a typical flow inside the drillpipe and drillcollars.

Unlike laminar flow, mud parameters (viscosity and yield point) are not significant in calculating frictional pressure losses for muds in turbulent flow.

Transitional flow : occurs when the fluid flow changes from laminar to turbulent or vice versa.

FLOW REGIME (cont’d)

Determination of the Laminar/Turbulent Boundary in a Newtonian Fluid:

Reynolds showed that when circulating Newtonian fluids through pipes the onset of turbulence was dependant on the following variables:

Pipe diameter, d Density of fluid, r Viscosity of fluid, μ Average flow velocity, v He also found that the onset of turbulence occurred when the following

combination of these variables exceeded a value of 2100 This grouping of variables is generally termed a dimensionless group and is known as the Reynolds number. In field units:

16

Types of flow

Laminar

Fig. 4-30. Laminar and turbulent flow patterns in a circular pipe: (a) laminar flow, (b) transition between laminar and turbulent flow and (c) turbulent flow

Turbulent

RheologyRheology is a science that uses a combination

of mathematical and empirical means. It attempts to predict the behavior of drilling

fluids as they are subjected to the influences of velocity, time, temperature and pressure.

Shear rate

• This is a term most applicable to laminar flow. It refers to the change in fluid velocity divided by the width of the channel through which the fluid is flowing in laminar flow.

Shear Stress

• The force per unit area required to move a fluid at a given shear rate.

Viscosity

• Viscosity is the representation of a fluid’s internal resistance to flow, defined as the ratio of shear stress to shear rate. Viscosity is expressed in poise.

• A poise is a very large number and therefore, viscosity is typically reported in centipoise

• (100 centipoise = 1 poise).

21

Rheological Models

Newtonian Bingham Plastic Power-Law

22

Newtonian Fluid Model

In a Newtonian fluid the shear stress is directly proportional to the shear rate (in laminar flow):

i.e.,

The constant of proportionality, is the viscosity of the fluid and is independent of shear rate.

sec

12

cm

dyne

23

Laminar Flow of Newtonian Fluids

A

F

L

V

Experimentally:

24

Newtonian Fluid Model

Viscosity may be expressed in poise or centipoise.

poise 0.01 centipoise 1

scm

g1

cm

s-dyne1 poise 1

2

2cm

secdyne

25

Shear Stress vs. Shear Rate for a Newtonian Fluid

Slope of line = m

.

26

Apparent Viscosity

Apparent viscosity = is the slope at each shear rate, .,, 321

/

28

Typical Drilling Fluid Vs. Newtonian, Bingham and Power Law Fluids

0

(Plotted on linear paper)

29

Rheological Models

1. Newtonian Fluid:

2. Bingham Plastic Fluid:

viscosityplastic

point yield

p

y

What if ty = 0?

py

rate shear

viscosity absolute

stress shear

30

API Power Law Model

K = consistency indexn = flow behaviour index

SHEAR STRESS

psi

= K n

SHEAR RATE, , sec-1

0

API RP 13D

API Power Law Model It describes the thickness or pumpability of the fluid, and is somewhat

analogous to the apparent viscosity. The flow behavior index (n) indicates the degree of non-Newtonian

characteristics of the fluid. As the fluid becomes more viscous, the consistency factors (k) increases;

as a fluid becomes more shear thinning “n” decreases. When “n” is 1 the fluid is Newtonian.

If “n” is greater than 1, the fluid is classed as Dilatant (the apparent viscosity increases as the shear rate increases).

If “n” is between zero and 1 the fluid is classified as Pseudoplastic, exhibiting shear-thinning; (i.e., the apparent viscosity decreases as the shear rate increases).

For drilling fluids, this is a desirable property and most drilling fluids are pseudoplastics.

32

RotatingSleeve

Viscometer

33

Table 4.3 - Summary of Equations for Rotational Viscometer

Newtonian Model

Na N

300

Nr

066.52

300a

or

34

Table 4.3 - Summary of Equations for Rotational Viscometer

300

N

or

1pNy 1

rpm 3 atmaxg

Bingham Plastic Model

300600p )(NN

300

or

12 NN12

p

p300y

or

or

Frictional Pressure Drop In Pipes and Anuli

When attempting to quantify the pressure losses inside the drillstring and in the annulus it is worth considering the following matrix:

Critical velocity

Critical velocity inside drill pipes and drill collars:

Critical velocity inside annulus:

Laminar Flow in Pipes and Annuli

The flow regime within which the fluid is flowing in a pipe or annulus will depend on the Reynolds number for the system in question.

The Reynolds number for each part of the system will however be different and it is possible for the fluid in one part of the system to be in laminar flow and the other in turbulent flow.

Laminar Flow in Pipes and Annuli (cont’d)

Hence the fluid may be in laminar flow in the drillpipe but in turbulent flow in the drillcollars. The equations which describe the pressure losses when the fluid is in laminar flow can be derived theoretically.

Laminar Flow in Pipes and Annuli (cont’d)

Equation for the pressure loss for the flow of a Newtonian Fluid in a pipe:

Equation for the flow of Newtonian Fluid in an annulus can be derived:

Laminar Flow in Pipes and Annuli (cont’d)Bingham Plastic Fluids

The equation for the frictional pressure loss in a pipe whilst circulating a Bingham Plastic Fluid is given by

The equation for the frictional pressure loss in an annulus whilst circulating a Bingham Plastic Fluid is given by :

Laminar Flow in Pipes and Annuli (cont’d) Power Law Fluid

The equation for the frictional pressure loss in a pipe whilst circulating a Power law Fluid is given by :

The equation for the frictional pressure loss in an annulus whilst circulating a Power law Fluid is given by :

Example:Pressure loss in Laminar Flow

a. Calculate the velocity of a fluid flowing through a 5" 19.5 lb/ft drillpipe (I.D.= 4.276") at 150 gpm.

b. Determine the pressure loss in the above situation if the fluid is a Bingham Plastic fluid with a plastic viscosity of 20 cp, a yield point of 15 lb/100 sq. ft and density is 10 ppg.

c. Calculate the pressure loss in the above situation if the fluid was a Power Law fluid with an non-Newtonian Index of 0.75 and a consistency index of 70 eq cp

Solution a. The velocity of a fluid flowing through a 5" 19.5 lb/ft drillpipe (I.D. =

4.276") at 150 gpm is:

b. If the fluid in the above situation is a Bingham Plastic fluid with a plastic viscosityof 20 cp, a yield point of 15 lb/100 sq. ft and density is 10 ppg the pressure loss inthe pipe will be:

c. The pressure loss in the above situation if the fluid was a Power Law fluid with an non-Newtonian Index of 0.75 and a consistency index of 70 eq cp would be:

Turbulent Flow

When the drilling fluid is pumped at a high rate the fluid laminar become unstable and break into a chaotic, diffused flow pattern. The fluid is then in turbulent flow.

Turbulent Flow of Newtonian Fluids in PipesThe equation for the pressure losses in turbulent flow of a Newtonian fluid in a pipe is derived from incorporating a control factor in the pressure loss

equation:

This equation is known as the Fanning Equation and the friction factor, f defined by this equation is called the Fanning friction factor. All of the terms in this equation, except for the friction factor, can be determined from the operating parameters. The friction factor, f is a function of the Reynolds Number NRe and a term called the relative roughness, e/d.

Fanning chart A plot of friction factor against Reynolds number on log-log

paper is called a Fanning chart:

Colebrook functionAn empirical correlation for the determination of

friction factors for fully developed turbulent flow in circular pipe has been presented by Colebrook. The Colebrook function is given by:

Turbulent Flow of Newtonian Fluids in annulus

FRICTIONAL PRESSURE DROP Across the Bit In practice, it is generally assumed that: 1. the change in pressure due to a change in elevation is negligible. 2. the velocity vo upstream of the nozzle is negligible, compared

with the nozzle velocity vn 3. the frictional pressure loss across the nozzle is negligible.

The exit velocity predicted for a given pressure drop across the bit, ΔPb, is never realised.

The actual velocity is always smaller than the velocity computed using previous Equation primarily because the assumption of frictionless flow is not strictly true.

To compensate for this difference, a correction factor or discharge coefficient Cd is usually introduced so that the modified equation:

The discharge coefficient may be as high as 0.98 but the recommended value is 0.95.

OPTIMISING THE HYDRA ULICS OF THE CIR CULATING SYSTEM

There are two different approaches to optimum hydraulics design:

a. Maximise the Hydraulic Horsepower at the Bit This assumes that the best method of cleaning

the hole is to concentrate as much fluid energy as possible at the bit.

b. Maximise the Hydraulic Impact at the Bit This assumes that the most effective method is to

maximise the force with which the fluid hits the bottom of the hole.