ch

ain

sp

roc

ke

tSIMPLEX

DUPLEX

TRIPLEX

SELECTION FACTORS ~ K FOR CHAIN SPROCKETS2

SELECTION FACTORS ~ K FOR CHAIN SPROCKETS1

CHAIN SPROCKET DRIVE

2

(for electric motors and steady driveunits - for internal combustionengines and other irregular drivesthe factor increase by .5)

Z1 teeth

= Ratio

internal combustion enginesload electric motorscharacteristic over 6 6 cylinder cylinders and lesssteady 1.0 1.4 2.0medium impulsive 1.5 1.8 2.3highly impulsive 2.0 2.3 2.6

17 19 21 23 25 27 30

excavators, crushers, calenders, pile drives,upsetting machines, construction machinery 2.43 2.35 2.27 2.19

hammer mills, riveting machines, rolling mills,rotary tillers, rubber mills 2.30 2.23 2.16 2.08

brick and tile machinery, moulding machineshoists, blower fans, slotting and stamping machines,planning machines 2.22 2.16 2.10 2.03 1.96

winches, straightening machines, drawing machines,presses, marine engines, ,minning machinery,compressors 2.07 2.01 1.95 1.89 1.83

reciprocating pumps, condensers, elevators, broachingmachine, machines working synthetic and ceramic materials, crushers 1.90 1.85 1.80 1.74 1.68

wood - working machines, stirring machines, mixersscreens, drilling plants. 1.78 1.73 1.68 1.63 1.58 1.52

looms knitting and spinning machines, bendingmachines 1.58 1.54 1.50 1.45 1.41 1.36

blowers shears, roller conveyors, windlasses,drying drums, cellulose-working machines, continuousconveyors 1.39 1.35 1.31 1.27 1.23 1.18

saws, milling machines, washing machines, centrifugalpumps, printing machines 1.20 1.17 1.14 1.11 1.08 1.04 1.00

conveyor belts, generators, lathes, drilling machines,packing machines, grinding machines 1.05 1.00 0.97 0.94 0.90 0.85 0.80

The Transmission of mechanical power without slippage and with a high degree of maintained efficiency is a basic function of the Roller Chain Drive.

SELECTION OF ROLLER CHAIN DRIVES1. Determine the R.P.M. and diameter of the high speed shaft.2. Determine the total H.P. to be transmitted.3. Select the chain pitch and number of teeth in the small sprocket, a) Be sure the small sprocket will accomodate the high speed shaft diameter. b) If the high speed shaft diameter exceeds the maximum bore in the selected small srpcket it will be necessary either to increase the number of teeth in the sprocket or select the next large pitch chain.4. Determine the required ratio: RPM high speed shaft RPM slow speed shaft5. Multiply the number of teeth in the small sprocket by the ratio to obtain the number of teeth in the large sprocket.6. The actual horsepower ‘P’ is multiplied by the correcting factor K1, K2 according to table.

CALCULATION VALUES AND FORMULAFOR CHAIN SPROCKETS

3

TERMS: ABBREVIATIONS: DIMENSIONS:

new old power P (N) [HP]

rated horsepower Pk [HP]

torque Md [mkp]

chain load pull F (P) [kp]

chain breaking strain FB (PB) [kp]

chain speed v [m/sec]

chain weight q [kp/m]-[kg/m]

drive speed n [rpm]

no.of teeth on drive z [-]

pitch P (t) [mm]

pitch circle diameter Do (Dt) [mm]

centre distance a [mm]

no. of chain links x [-]

bearing area f [cm2]

no. of teeth on driving wheel z1 [-]

no.of teeth on driven wheel z2 [-]

teeth no. factor y (n) [-]

chain sag hk (f) [mm]

horsepower :

torque :

chain speed :

chain load pull :

pitch circle diameter :

Formulae : velocity ratio :

X

STANDARD CHAIN WHEEL AND PINIONFor Simplex BSS Roller Chain

4

PITCH PTC TEETH P.C.D. DIA BOSS BORE TOTAL TEETH NO. DIA LENGTH FACE B A C D L T

3/8” 038131 13 39.80 44 30 10.0 23.0 5.2 9.525 mm 038151 15 45.81 50 32 12.7 23.0 “ 038171 17 51.84 55 38 12.7 23.0 “ 038191 19 57.87 62 45 12.7 23.0 “ 038211 21 63.91 68 52 12.7 23.0 “ 038231 23 69.95 74 58 12.7 23.0 “ 038251 25 76.00 80 63 12.7 24.0 “ 038301 30 91.12 96 76 19.1 24.0 “ 038381 38 115.34 119 90 19.1 25.0 “ 038571 57 172.91 177 67 19.1 35.0 “ 038761 76 230.49 234 77 19.1 35.0 “ 038951 95 288.08 292 95 25.4 43.0 “ 1/2” 012131 13 53.07 59 38 12.7 25.0 7.1 12.7mm 012151 15 61.08 66 45 12.7 25.0 “ 012171 17 69.12 74 50 12.7 25.0 “ 012191 19 77.16 82 60 12.7 26.0 “ 012211 21 85.21 90 64 19.1 26.0 “ 012231 23 93.27 98 78 19.1 26.0 “ 012251 25 101.33 107 80 19.1 26.0 “ 012301 30 121.50 127 90 19.1 27.0 “ 012381 38 153.79 159 75 28.0 38.0 “ 012571 57 230.54 235 86 31.0 41.0 “ 012761 76 307.32 312 96 31.0 41.0 “ 012951 95 384.11 389 105 35.0 45.0 “ 5/8” 058131 13 66.34 73 51 12.7 28.0 8.5 15.875mm 058151 15 76.36 83 58 19.1 28.0 “ 058171 17 86.39 93 65 19.1 29.5 “ 058191 19 96.45 104 75 19.1 30.0 “ 058211 21 106.51 114 90 19.1 30.0 “ 058231 23 116.58 123 95 19.1 30.0 “ 058251 25 126.66 133 100 19.1 30.0 “ 058381 38 192.24 198 85 19.1 40.0 “ 058571 57 288.18 295 95 25.4 40.0 “ 058761 76 384.15 391 115 25.4 50.0 “ 058951 95 480.14 487 120 25.4 50.0 3/4” 034131 13 79.60 88 60 19.1 28.5 10.5 19.05mm 034151 15 91.62 99 70 19.1 30.5 “ 034171 17 103.67 113 80 19.1 30.5 “ 034191 19 115.74 123 90 19.1 30.5 “ 034211 21 127.82 135 97 19.1 30.5 “ 034231 23 139.90 148 76 19.1 40.0 “ 034251 25 151.99 160 76 19.1 40.0 “ 034301 30 182.25 190 86 25.4 40.0 “ 034381 38 230.69 239 96 25.4 40.0 “ 034571 57 345.81 357 106 25.4 45.0 “ 034761 76 460.98 469 120 25.4 45.0 “ 034951 95 576.17 858 135 31.7 50.8 “

PITCH PTC TEETH P.C.D. DIA BOSS BORE TOTAL TEETH NO. DIA LENGTH FACE B A C D L T

1” 100131 13 106.14 118 81 19.1 40 15.9 25.4mm 100151 15 122.17 134 95 25.4 40 “ 100171 17 138.23 149 108 25.4 40 “ 100191 19 154.32 166 96 25.4 52 “ 100211 21 170.42 181 96 25.4 52 “ 100231 23 186.54 199 96 25.4 52 “ 100251 25 202.66 215 105 25.4 52 “ 100381 38 307.58 318 120 25.4 52 “ 100571 57 461.08 473 135 32.0 60 “ 100761 76 614.64 627 145 32.0 65 “ 100951 95 768.22 780 160 38.0 65 “ 1.1/4” 114131 13 132.67 146 100 25.4 45 18.0 31.75mm 114151 15 152.71 170 95 25.4 55 “ 114171 17 172.79 187 95 25.4 55 “ 114191 19 192.90 208 105 25.4 55 “ 114211 21 213.03 227 105 25.4 55 “ 114231 23 233.17 249 105 25.4 55 “ 114251 25 253.32 266 105 25.4 55 “ 114381 38 384.48 398 120 31.7 65 “ 114571 57 576.35 593 145 31.7 65 “ 114761 76 768.30 783 170 38.1 75 “ 114951 95 960.28 975 170 38.1 75 “ 1.1/2” 112131 13 159.20 174 115 25.4 50 23.0 38.1mm 112151 15 183.25 198 100 25.4 65 “ 112171 17 207.35 223 100 25.4 65 “ 112191 19 231.48 247 105 25.4 65 “ 112211 21 255.63 270 105 25.4 65 “ 112231 23 279.80 295 115 25.4 65 “ 112251 25 303.99 320 115 25.4 70 “ 112381 38 461.38 477 135 31.7 70 “ 112571 57 691.63 706 155 38.1 75 “ 112761 76 921.93 936 175 38.1 75 “ 112951 95 1152.32 1268 200 44.5 90 “ 1.3/4” 134131 13 185.74 207 130 25.4 58 28.0 44.45mm 134151 15 213.79 235 100 25.4 70 “ 134171 17 241.91 264 105 25.4 70 “ 134191 19 270.06 292 105 25.4 70 “ 134211 21 298.24 320 115 31.7 70 “ 134231 23 326.44 347 115 31.7 70 “ 134251 25 354.65 376 120 31.7 70 “ 134381 38 538.27 560 140 31.7 80 “ 134571 57 806.90 829 160 38.1 90 “ 134761 76 1075.62 1097 175 38.1 90 “ 2” 200131 13 212.27 235 100 25.4 70 28.0 50.8MM 200151 15 244.33 270 105 25.4 70 “ 200171 17 276.46 305 115 31.7 75 “ 200191 19 308.64 335 115 31.7 75 “ 200211 21 340.84 370 120 31.7 75 “ 200231 23 373.07 400 120 31.7 80 “ 200251 25 405.32 435 135 38.1 80 “ 200381 38 615.17 644 145 38.1 90 “ 200571 57 922.17 950 175 45.0 90 “ 200761 76 1229.28 1255 200 45.0 100 “ 2.1/2” 212131 13 265.64 300 115 31.7 80 34.5 63.5MM 212151 15 305.42 340 115 31.7 80 “ 212171 17 345.58 375 120 31.7 80 “ 212191 19 385.79 415 135 38.1 85 “ 212211 21 426.05 459 135 38.1 85 “ 212231 23 466.34 499 145 38.1 90 “ 212251 25 506.65 539 145 45.0 95 “ 212381 38 768.96 800 160 45.0 95 “ 212571 57 1152.71 1185 190 50.0 100 “ 212761 76 1536.60 1565 210 50.0 110 “

STANDARD CHAIN WHEEL AND PINIONFor Simplex BSS Roller Chain

5

STANDARD CHAIN WHEEL AND PINIONFor Duplex BSS Roller Chain

6

PITCH PTC TEETH P.C.D. DIA BOSS BORE TOTAL TEETH NO. DIA LENGTH FACE B A C D L T

3/8” 038132 13 39.80 44 30 10.0 30 15.0 9.525mm 038152 15 45.81 50 32 12.7 30 “ 038172 17 51.84 55 38 12.7 30 “ 038192 19 57.87 62 45 12.7 30 “ 038212 21 63.91 68 52 12.7 32 “ 038232 23 69.95 74 58 12.7 32 “ 038252 25 76.00 80 63 12.7 32 “ 038302 30 91.92 96 76 19.1 34 “ 038382 38 115.34 119 90 19.1 34 “ 038572 57 172.91 177 75 19.1 40 “ 038762 76 230.49 234 85 25.4 40 “ 038952 95 288.08 292 95 25.4 45 “ 1/2” 012132 13 53.08 59 38 12.7 37 21.0 12.7mm 012152 15 61.03 66 45 12.7 37 “ 012172 17 69.12 74 50 12.7 40 “ 012192 19 77.16 82 60 19.1 40 “ 012212 21 85.21 90 64 19.1 40 “ 012232 23 93.27 98 78 19.1 40 “ 012252 25 101.33 107 85 19.1 40 “ 012302 30 121.50 127 90 19.1 40 “ 012382 38 153.79 159 85 19.1 40 “ 012572 57 230.54 235 95 25.4 50 “ 012762 76 307.32 312 108 25.4 50 “ 012952 95 384.11 389 115 25.4 50 “ 5/8” 058132 13 66.34 73 51 12.7 42 25.0 15.875mm 058152 15 76.36 83 58 19.1 42 “ 058172 17 86.39 93 65 19.1 44 “ 058192 19 96.45 104 75 19.1 44 “ 058212 21 106.51 114 90 19.1 44 “ 058232 23 116.58 123 95 19.1 44 “ 058252 25 126.66 133 100 19.1 44 “ 058382 38 192.24 198 86 25.4 55 “ 058572 57 288.18 295 96 25.4 55 “ 058762 76 384.15 391 105 25.4 60 “ 058952 95 480.13 487 120 31.7 60 “ 3/4” 034133 13 79.60 88 60 19.1 50 30.0 19.05mm 034153 15 91.62 99 70 19.1 50 “ 034172 17 103.67 113 80 19.1 50 “ 034192 19 115.74 123 90 19.1 50 “ 034212 21 127.82 135 97 19.1 50 “ 034232 23 139.90 148 115 19.1 50 “ 034252 25 151.99 160 125 19.1 50 “ 034382 38 230.69 239 105 25.4 60 “ 034572 57 345.81 357 120 25.4 60 “ F 034762 76 460.98 468 135 31.7 60 “ F 034952 95 587.17 585 135 31.7 65 “

STANDARD CHAIN WHEEL AND PINIONFor Duplex BSS Roller Chain

7

PITCH PTC TEETH P.C.D. DIA BOSS BORE TOTAL TEETH NO. DIA LENGTH FACE B A C D L T

1” 100132 13 106.14 118 81 25.4 72 48.0 25.4mm 100152 15 122.17 134 95 25.4 72 “ 100172 17 138.23 149 108 25.4 72 “ 100192 19 154.32 166 106 25.4 72 “ 100212 21 170.42 181 106 25.4 72 “ 100232 23 186.54 199 106 25.4 85 “ 100252 25 202.66 215 120 25.4 85 “ 100382 38 307.58 318 125 31.7 85 “ F 100572 57 461.08 476 135 38.1 85 “ F 100762 76 614.64 627 160 38.1 85 “ F 100952 95 768.22 780 175 45.0 85 “ 1.1/4” 114132 13 132.67 146 100 25.4 80 54.6 31.75mm 114152 15 152.71 170 106 25.4 80 “ 114172 17 172.79 187 135 25.4 80 “ 114192 19 192.90 208 115 25.4 85 “ 114212 21 213.03 227 115 25.4 85 “ 114232 23 233.17 249 115 25.4 85 “ 114252 25 253.32 266 120 25.4 85 “ F 114382 38 384.48 398 135 31.7 85 “ F 114572 57 576.35 593 150 31.7 90 “ F 114762 76 768.30 783 170 31.7 90 “ F 114952 95 960.28 975 200 38.1 90 “ 1.1/2” 112132 13 159.20 174 115 25.4 100 71.0 38.1mm 112152 15 183.25 198 135 25.4 100 “ 112172 17 207.35 223 115 25.4 105 “ 112192 19 231.48 247 115 25.4 105 “ 112212 21 255.63 270 120 25.4 105 “ 112232 23 279.80 295 120 31.7 105 “ 112252 25 303.99 320 125 31.7 105 “ F 112382 38 461.38 477 140 38.1 110 “ F 112572 57 691.63 706 160 38.1 110 “ F 112762 76 921.93 936 180 45.0 110 “ 1.3/4” 134132 13 185.74 207 115 25.4 120 88.0 44.45mm 134152 15 213.79 235 115 25.4 120 “ 134172 17 241.91 264 115 25.4 120 “ 134192 19 270.06 292 120 31.7 120 “ 134212 21 298.24 320 120 31.7 120 “ 134232 23 326.44 347 125 31.7 120 “ 134252 25 354.65 376 135 38.1 120 “ F 134382 38 538.27 560 150 38.1 125 “ F 134572 57 806.90 829 175 45.0 125 “ F 134762 76 1075.62 1097 190 45.0 125 “ 2” 200132 13 212.27 235 120 25.4 120 87.0 50.8MM 200152 15 244.33 270 120 31.7 120 “ 200172 17 276.46 305 125 31.7 120 “ 200192 19 308.64 335 125 31.7 120 “ 200212 21 340.84 370 125 31.7 120 “ F 200232 23 373.07 400 135 38.1 120 “ F 200252 25 405.32 435 135 38.1 120 “ F 200382 38 615.17 644 150 45.0 125 “ F 200572 57 922.17 950 175 45.0 125 “ F 200762 76 1229.28 1255 200 45.0 125 “ 2.1/2” 212132 13 265.64 300 125 31.7 140 107.0 212152 15 305.42 340 125 31.7 140 “ 63.5mm 212172 17 345.58 375 125 31.7 140 “ 212192 19 385.79 415 135 38.1 140 “ 212212 21 426.05 459 135 38.1 140 “ F 212232 23 466.34 499 145 38.1 140 “ F 212252 25 506.65 539 150 38.1 140 “ F 212382 38 768.96 800 175 45.0 145 “ F 212572 57 1152.71 1185 200 45.0 145 “ F 212762 76 1536.60 1565 200 45.0 145 “

STANDARD CHAIN WHEEL AND PINIONFor Triplex BSS Roller Chain

8

PITCH PTC TEETH P.C.D. DIA BOSS BORE TOTAL TEETH NO. DIA LENGTH FACE B A C D L T

3/8” 038133 13 39.80 44 30 12.7 40 25.0 9.525mm 038153 15 45.81 50 32 12.7 40 “ 038173 17 51.84 55 38 12.7 40 “ 038193 19 57.87 62 45 12.7 42 “ 038213 21 63.91 68 52 12.7 42 “ 038233 23 69.95 74 58 12.7 44 “ 038253 25 76.00 80 63 12.7 44 “ 038303 30 91.12 96 76 19.7 44 “ 038383 38 115.34 119 90 19.1 45 ‘ 038573 57 172.91 177 95 19.1 50 “ 038763 76 230.49 234 95 25.4 50 “ 038953 95 288.08 292 95 25.4 50 “ 1/2” 012133 13 53.07 59 38 12.7 50 35.0 12.7mm 012153 15 61.08 66 45 12.7 50 “ 012173 17 69.12 74 50 12.7 52 “ 012193 19 77.16 82 60 19.1 54 “ 012213 21 85.21 90 64 19.1 54 “ 012233 23 93.27 98 78 19.1 54 “ 012253 25 101.33 107 85 19.1 54 “ 012303 30 121.50 127 90 19.1 54 “ 012383 38 153.79 159 95 25.4 63 “ 012573 57 230.54 235 105 25.4 63 “ 012763 76 307.32 312 115 25.4 65 “ 012953 95 384.11 389 120 31.7 65 “ 5/8” 058133 13 66.34 73 51 12.7 58 42.0 15.875mm 058153 15 76.36 83 58 19.1 60 “ 058173 17 86.39 93 65 19.1 60 “ 058193 19 96.45 104 75 19.1 60 “ 058213 21 106.51 114 90 19.1 60 “ 058233 23 116.58 123 95 19.1 60 “ 058253 25 126.66 133 100 19.1 60 “ 058383 38 192.54 198 95 25.4 70 “ 058573 57 238.18 295 108 25.4 70 “ F 058763 76 384.15 391 120 31.7 70 “ F 058953 95 480.14 487 135 31.7 70 “ 3/4” 034133 13 79.60 88 60 19.1 70 49.0 19.05mm 034153 15 91.62 99 70 19.1 70 “ 034173 17 103.67 113 80 19.1 70 “ 034193 19 115.74 123 90 19.1 70 “ 034213 21 127.82 135 97 19.1 70 “ 034233 23 139.90 148 115 19.1 70 “ 034253 25 151.99 160 125 25.4 70 “ 034383 38 230.69 190 120 25.4 80 “ F 034573 57 345.81 357 130 31.7 80 “ F 034763 76 460.98 469 135 31.7 80 “ F 034953 95 579.17 585 145 38.1 80 “

STANDARD CHAIN WHEEL AND PINIONFor Triplex BSS Roller Chain

9

PITCH PTC TEETH P.C.D. DIA BOSS BORE TOTAL TEETH NO. DIA LENGTH FACE B A C D L T

1” 100133 13 106.14 118 81 25.4 105 80.0 25.4mm 100153 15 122.17 135 95 25.4 105 “ 100173 17 138.23 151 108 25.4 105 “ 100193 19 154.32 167 127 25.4 105 “ 100213 21 170.42 183 140 25.4 105 “ 100233 23 186.54 198 115 25.4 105 “ 100253 25 202.66 215 120 31.7 110 “ 100383 38 307.58 320 135 31.7 110 “ F 100573 57 461.08 473 145 38.1 110 “ F 100763 76 614.64 627 165 45.0 110 “ F 100953 95 768.22 780 190 45.0 110 “ 1.1/4” 114133 13 132.67 146 100 25.4 120 91.0 31.75mm 114153 15 152.71 170 120 25.4 120 “ 114173 17 172.79 187 135 25.4 120 “ 114193 19 192.90 208 115 31.7 125 “ 114213 21 213.03 227 120 31.7 125 “ 114233 23 233.17 249 120 31.7 125 “ 114253 25 253.32 266 125 38.1 125 “ F 114383 38 384.48 398 135 38.1 125 “ F 114573 57 576.35 598 160 38.1 125 “ F 114763 76 768.30 783 175 45.0 125 “ F 114953 95 960.28 975 190 45.0 125 “ 1.1/2” 112133 13 159.20 175 115 25.4 145 119.7 38.1mm 112153 15 183.25 197 135 25.4 145 “ 112173 17 207.35 223 115 31.7 150 “ 112193 19 231.48 245 120 31.7 150 “ 112213 21 255.63 271 120 31.7 150 “ 112233 23 279.80 295 125 38.1 150 “ 112253 25 303.99 317 135 38.1 150 “ F 112383 38 461.38 477 150 45.0 155 “ F 112573 57 691.63 707 175 45.0 160 “ F 112763 76 921.96 937 200 45.0 160 “ 1.3/4” 134133 13 185.74 207 115 25.4 180 148.0 44.45MM 134153 15 213.79 235 115 25.4 180 “ 134173 17 241.91 264 120 31.7 180 “ 134193 19 270.06 292 125 31.7 180 “ 134213 21 298.24 320 135 31.7 180 “ 134233 23 326.44 347 135 38.1 180 “ 134253 25 354.65 376 145 38.1 180 “ F 134383 38 538.27 560 170 45.0 180 “ F 134573 57 806.90 829 190 45.0 180 “ F 134763 76 1075.62 1097 200 50.0 180 “ 2” 200133 13 212.27 235 120 31.7 180 146.3 50.8mm 200153 15 244.33 270 125 31.7 180 “ 200173 17 276.46 305 135 31.7 180 “ 200193 19 308.64 335 135 31.7 180 “ 200213 21 340.84 370 145 38.1 185 “ F 200233 23 373.07 400 145 38.1 185 “ F 200253 25 405.32 435 160 38.1 185 “ F 200383 38 615.17 644 180 45.0 185 “ F 200573 57 922.17 950 200 45.0 185 “ F 200763 76 1229.28 1255 215 50.0 185 “ 2.1/2” 212133 13 265.64 300 125 31.7 210 179.6 212153 15 305.42 345 125 31.7 210 “ 63.5mm 212173 17 345.58 375 125 38.1 210 “ 212193 19 385.79 415 140 38.1 210 “ 212213 21 426.05 459 140 38.1 210 “ F 212233 23 466.34 499 150 38.1 210 “ F 212253 25 506.65 539 170 45.0 210 “ F 212383 38 768.96 800 180 45.0 215 “ F 212573 57 1152.71 1185 200 45.0 215 “ F 212763 76 1536.60 1565 215 45.0 215 “

CHAIN WHEEL RIM PROFILE DIMENSIONS

10

PITCH ROLLER

DIA

WIDTH

BETWEEN

INNER

PLATES

TOOTH WIDTH

SIMPLEX

C1

MAX MIN

WIDTH OVER

TEETH DUPLEX

C2

MAX MIN

WIDTH OVER

TEETH TRIPLEX

C3

MAX MIN

TOOTH

SIDE

RADIUS

F

SIDE

RELIEF

G

SHROUD

DEPTH

J

RELIEF

DEPTH

C

0.315”

0.375

0.500

0.625

0.750

1.000

1.250

1.500

1.750

2.000

2.500

3.000

0.197”

0.250

0.335

0.400

0.475

0.625

0.750

1.000

1.100

1.150

1.550

1.900

0.118”

0.225

0.305

0.380

0.460

0.670

0.770

1.000

1.220

1.220

1.500

1.800

0.106

0.210

0.285

0.356

0.433

0.635

0.731

0.952

1.163

1.163

1.432

1.720

0.100

0.201

0.275

0.345

0.420

0.618

0.712

0.928

1.135

1.135

1.398

1.680

0.328

0.613

0.833

1.009

1.199

1.890

2.166

2.856

3.508

3.468

4.278

5.311

0.322

0.604

0.823

0.998

1.186

1.873

2.147

2.832

3.480

3.440

4.244

5.271

0.550

1.016

1.381

1.662

1.965

3.145

3.601

4.760

5.853

5.773

7.124

8.902

0.544

1.007

1.371

1.651

1.952

3.128

3.582

4.736

5.825

5.745

7.090

8.862

0.315

0.375

0.500

0.625

0.750

1.000

1.250

1.500

1.750

2.000

2.500

3.000

0.032

0.038

0.050

0.063

0.075

0.100

0.125

0.150

0.175

0.200

0.250

0.300

0.085

0.130

0.110

0.135

0.150

0.175

0.215

0.230

0.320

0.400

0.410

0.450

0.125

0.187

0.250

0.312

0.375

0.500

0.625

0.750

0.875

1.000

1.250

1.500

CHAIN

NO.

PITCH ROLLER

DIA

GAP

N

0.2500.3750.5000.5000.6250.7501.0001.2501.5001.7502.0002.5003.000

0.1300.2000.3060.3120.4000.4690.6250.7500.8751.0001.1251.5621.875

0.1250.1870.2500.3120.3750.5000.6250.7501.0001.0001.2501.5001.875

0.1100.1680.2270.2840.3430.4590.5750.6920.9240.9241.1561.3891.738

0.3580.559 —0.8431.0431.3431.7092.0792.6812.8193.4214.1615.138

0.6100.957 —1.4091.7562.2402.8623.4884.4694.7445.7246.9808.594

0.1460.236 —0.2910.3820.4530.5980.7400.8941.0311.1851.4761.776

0.0320.0480.0620.0620.0780.0930.1250.1560.1870.2180.2500.3120.375

0.1250.1870.2500.2500.3120.3750.5000.6250.7500.8751.0001.2501.500

0.0850.1100.1100.1100.1350.1500.1750.2150.2300.3200.4000.4200.450

0.2500.3750.5000.5000.6250.7501.0001.2501.5001.7502.0002.5003.000

WIDTH

BETWEEN

INNER

PLATES

TEETH

THICKNESS

T

SIDE

RELIEF

G

RELIEF

DEPTH

C

SHROUND

DEPTH

J

TOOTH

SIDE

RADIUS

F

SIMPLEX

M1

DUPLEX

M2

TRIPLEX

M3

0.1070.162 —0.2750.3320.4440.5570.6690.8940.8941.1191.3441.632

TOOTH WIDTH

For American Standard Roller Chain

For British Standard Roller Chain

RC. 25RC. 35RC. 41RC. 40RC. 50RC. 60RC. 80RC. 100RC. 120RC. 140RC. 160RC. 200RC. 240

RENOLD & ROLON CHAINS

a) Transmission Roller Chainb) Leaf Chain (Weight Lifting Chain)c) Stenter (Process) Machine Chaind) Flat Card Chaine) Conveyor Chainf ) Geared Motor g) Couplings

a) Solid Bearing Typeb) Hollow Bearing Type

CHAINS & OTHER PRODUCTS

11

AUTHORISED DISTRIBUTOR :

TRANSMISSION AND CONVEYOR CHAIN

(ISO 9001 CERTIFIED)AND

• 'CETRON' WORM REDUCTION GEAR BOX & SPARES FOR ANY MAKE OF GEAR BOX• HINDUSTAN (ISO 9001) ELECTRIC MOTOR & GEARED MOTOR • PIV CHAINS & SPARES FOR PIV GEAR BOX • SILENT (INVERTED TOOTH) CHAINS• DRAG CHAINS• SPROCKET WHEELS & ALL TYPES OF GEARS• SPLINE SHAFT AND RACK & PINION• COUPLINGS & PULLEY

11-13, Horniman Circle, Botawala Building, 3rd Floor, Fort, Mumbai 400 023.Tel.: +91-22-2266 1837 / 2266 5253 / 2269 5324 • Fax : +91-22-2266 5253 E-mail : rolon@mtnl.net.in • Web : www.paramounttrans.net