Upload
others
View
6
Download
0
Embed Size (px)
Citation preview
FunctionThe CDT 30 is a robust, cost-effective and energy-efficient, reliable mobile de-humidifier. It works in accordance with the condensation principle. A fan draws the humid air into the dehumidifier and through an evaporator coil. When passing through the evaporator the air is cooled down to below its dew point temperature, and its content of water vapour is condensed into water, which is collected in the water container.
Applications• Damage service• Building drying• Water works• Dry storing
Dehumidifier• High capacity• Low energy consumption• Strong and robust cabinet of powder coated hot galvanized steel• Epoxy coated evaporator and condenser.• Adjustable handle• Plastic bumpers• Low weight• Stackable.• Large wheels
Water container• Water container with handles• Automatic stop when water container is full or removed.• Permanent drainage can be established with optional ½” hose connection• Condensate pump in a cassette as optional extra
Electronic control• Digital touchpad control panel with display• Accurate hour and kWh counter (reading)• RH and °C monitoring (reading)• RH setting• Easy fault-finding• Service monitoring function
DefrostingActive, demand-controlled defrosting which is activated through a tempera-ture sensor on the evaporator. Defrosting is done by means of hot refrigerant being fed through the evaporator.
CDT 30
CDT 30MOBILE DEHUMIDIFIER
FEATURES
MOBILE DEHUMIDIFIERS CDT
Digital touchpad control panel:1. On-off switch2. Reading of room temperature3. Indicator for normal operation (green lamp)4. Reading of RH value / setting of RH value5. Indicator for full water container (yellow lamp)6. Failure indicator (red lamp)7. Hour counter / setting of service intervals8. kWh counter
Specific energy consumption (SEC)• 0,47 kWh/l at 30°C & 80% RH• 0,85 kWh/l at 20°C & 60% RH
Accessories½” drain outletRemote hygrostatWall bracketDual voltage kitCondensate pump in a cassette(see separate data sheet)
Also available in this series:CDT 30 SCDT 40CDT 40 SCDT 60CDT 90(see separate data sheets)
Model CDT 30Operating range – humidity 40-100% RHOperating range – temperature 3-32°CAir volume 250 m³/hPower supply 230 V/50 HzMax. ampere consumption 2,7 AMax. power consumption 0,590 kWRefrigerant R 134aCompressor type RotarySound level (at 1 metre) 56 dB(A)Water container capacity 7 litresColour - water container and wheel cap RAL 7015Colour - front grille RAL 7044Colour - control panel and bumpers RAL 9005Protection class IP X4Filter PPI 15Wheel size Ø 250 mmWheel and water container material PPControl panel material ABSWeight 32 kg
dantherm.com
TECHNICAL DATA
CAPACITY CURVES
DIMENSIONS
MOBILE DEHUMIDIFIERS CDT
Sheetmetal flatstate is based on Dantherm A/S process equipment and is only entended as a guide.
AND WILL BE PROTECTED BY PATENTS
table LZT 142 0001, category
ohr
03-01-2012
Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)
65610.26g
SCALE: NOT TO SCALE
351 189
351189
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
PART NO
8Surface appearance according to reference BEND RADII:
ARE THE PROPERTY OF SAID COMPANY
Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH)
REV.:
RE
V.:
CDT 30 MK II
CDT 30 MK II
PA
RT
NO
THIS DRAWING IS FURNISHED WITH THE UNDERSTANDING THAT THE ESSENCE THERE OF WILL NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT WRITTEN AUTHORIZATION BY Dantherm A/S. ALL DESIGNS ORIGINATED BY Dantherm A/S
Linear dimensions without tolerances according to DS/EN 22768-1 mediumAngular dimensions without tolerances: ± 1°
740
650
506
427
Sheetmetal flatstate is based on Dantherm A/S process equipment and is only entended as a guide.
AND WILL BE PROTECTED BY PATENTS
table LZT 142 0001, category
ohr
03-01-2012
Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)
65610.26g
SCALE: NOT TO SCALE
351 189
351189
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
PART NO
8Surface appearance according to reference BEND RADII:
ARE THE PROPERTY OF SAID COMPANY
Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH)
REV.:
RE
V.:
CDT 30 MK II
CDT 30 MK II
PA
RT
NO
THIS DRAWING IS FURNISHED WITH THE UNDERSTANDING THAT THE ESSENCE THERE OF WILL NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT WRITTEN AUTHORIZATION BY Dantherm A/S. ALL DESIGNS ORIGINATED BY Dantherm A/S
Linear dimensions without tolerances according to DS/EN 22768-1 mediumAngular dimensions without tolerances: ± 1°
740
650
506
427
Sheetmetal flatstate is based on Dantherm A/S process equipment and is only entended as a guide.
AND WILL BE PROTECTED BY PATENTS
table LZT 142 0001, category
ohr
03-01-2012
Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)
65610.26g
SCALE: NOT TO SCALE
351 189
351189
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
PART NO
8Surface appearance according to reference BEND RADII:
ARE THE PROPERTY OF SAID COMPANY
Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH)
REV.:
RE
V.:
CDT 30 MK II
CDT 30 MK II
PA
RT
NO
THIS DRAWING IS FURNISHED WITH THE UNDERSTANDING THAT THE ESSENCE THERE OF WILL NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT WRITTEN AUTHORIZATION BY Dantherm A/S. ALL DESIGNS ORIGINATED BY Dantherm A/S
Linear dimensions without tolerances according to DS/EN 22768-1 mediumAngular dimensions without tolerances: ± 1°
740
650
506
427
0 0,2 0,4 0,6 0,8 1,0 1,2 1,4 1,60
5
10
15
20
25
30
35°C
L/H
60%40% 80%
All dimensions are in mm.
736
650
426
FunctionThe CDT 30 S is a robust, cost-effective and energy-efficient, reliable mobile de-humidifier. It works in accordance with the condensation principle. A fan draws the humid air into the dehumidifier and through an evaporator coil. When passing through the evaporator the air is cooled down to below its dew point temperature, and its content of water vapour is condensed into water, which is collected in the water container.
Applications• Damage service• Building drying• Water works• Dry storing
Dehumidifier• High capacity• Low energy consumption• Strong and robust cabinet of powder coated hot galvanized steel• Epoxy coated evaporator and condenser.• Adjustable handle• Plastic bumpers• Low weight• Stackable.• Large wheels• On the back two Ø100 mm flex. air ducts may be connected
(max. length of 5 m) (accessory)• Built-in 1 kW heating element• Supplied with high pressure fan
Water container• Water container with handles• Automatic stop when water container is full or removed.• Permanent drainage can be established with optional ½” hose connection• Condensate pump in a cassette as optional extra
Electronic control• Digital touchpad control panel with display• Accurate hour and kWh counter (reading)• RH and °C monitoring (reading)• RH setting• Easy fault-finding• Service monitoring function
DefrostingActive, demand-controlled defrosting which is activated through a tempera-ture sensor on the evaporator. Defrosting is done by means of hot refrigerant being fed through the evaporator.
Digital touchpad control panel:1. On-off switch2. Reading of room temperature3. Indicator for normal operation (green lamp)4. Reading of RH value / setting of RH value5. Indicator for full water container (yellow lamp)6. Failure indicator (red lamp)7. Hour counter / setting of service intervals8. kWh counter
CDT 30 S
CDT 30 SMOBILE DEHUMIDIFIER
FEATURES
MOBILE DEHUMIDIFIERS CDT
Specific energy consumption (SEC)• 0,43 kWh/l at 30°C & 80% RH• 0,86 kWh/l at 20°C & 60% RH
Accessories½” drain outletRemote hygrostatWall bracketDual voltage kitCondensate pump in a cassetteFlex. air ducts Ø100 mm(see separate data sheet)
Also available in this series:CDT 30CDT 40CDT 40 SCDT 60CDT 90(see separate data sheets)
Model CDT 30 SOperating range – humidity 40-100% RHOperating range – temperature 3-32°CAir volume 350 m³/h*Power supply 230 V/50 HzMax. ampere consumption 2,6 AMax. power consumption with heating element 1,56 kWMax. power consumption without heating element 0,56 kWRefrigerant R 134aCompressor type RotarySound level (at 1 metre) 60 dB(A)**Water container capacity 7 litresColour - water container and wheel cap RAL 7015Colour - front grille RAL 7044Colour - control panel and bumpers RAL 9005Protection class IP X4Filter PPI 15Wheel size Ø 250 mmWheel and water container material PPControl panel material ABSWeight 34 kg
dantherm.com
TECHNICAL DATA
CAPACITY CURVES
DIMENSIONS
MOBILE DEHUMIDIFIERS CDT
CDT 30 S MK II
CDT 30 S MK IISCALE: NOT TO SCALE
64278.09g
BEND RADII:
24-05-2012
ohr
351190
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
PART NO REV.:
RE
V.:
PA
RT
NO
Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH)Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)
351 190
only entended as a guide.
8
Sheetmetal flatstate is based on Dantherm A/S process equipment and is
table LZT 142 0001, category Surface appearance according to reference
ARE THE PROPERTY OF SAID COMPANY AND WILL BE PROTECTED BY PATENTS
THIS DRAWING IS FURNISHED WITH THE UNDERSTANDING THAT THE ESSENCE THERE OF WILL NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT WRITTEN AUTHORIZATION BY Dantherm A/S. ALL DESIGNS ORIGINATED BY Dantherm A/S
Linear dimensions without tolerances according to DS/EN 22768-1 mediumAngular dimensions without tolerances: ± 1°
750
650
506
426
CDT 30 S MK II
CDT 30 S MK IISCALE: NOT TO SCALE
64278.09g
BEND RADII:
24-05-2012
ohr
351190
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
PART NO REV.:
RE
V.:
PA
RT
NO
Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH)Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)
351 190
only entended as a guide.
8
Sheetmetal flatstate is based on Dantherm A/S process equipment and is
table LZT 142 0001, category Surface appearance according to reference
ARE THE PROPERTY OF SAID COMPANY AND WILL BE PROTECTED BY PATENTS
THIS DRAWING IS FURNISHED WITH THE UNDERSTANDING THAT THE ESSENCE THERE OF WILL NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT WRITTEN AUTHORIZATION BY Dantherm A/S. ALL DESIGNS ORIGINATED BY Dantherm A/S
Linear dimensions without tolerances according to DS/EN 22768-1 mediumAngular dimensions without tolerances: ± 1°
750
650
506
426
CDT 30 S MK II
CDT 30 S MK IISCALE: NOT TO SCALE
64278.09g
BEND RADII:
24-05-2012
ohr
351190
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
PART NO REV.:
RE
V.:
PA
RT
NO
Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH)Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)
351 190
only entended as a guide.
8
Sheetmetal flatstate is based on Dantherm A/S process equipment and is
table LZT 142 0001, category Surface appearance according to reference
ARE THE PROPERTY OF SAID COMPANY AND WILL BE PROTECTED BY PATENTS
THIS DRAWING IS FURNISHED WITH THE UNDERSTANDING THAT THE ESSENCE THERE OF WILL NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT WRITTEN AUTHORIZATION BY Dantherm A/S. ALL DESIGNS ORIGINATED BY Dantherm A/S
Linear dimensions without tolerances according to DS/EN 22768-1 mediumAngular dimensions without tolerances: ± 1°
750
650
506
426
0
5
10
15
20
25
30
35°C
L/H
40% 60% 80%
0 0,2 0,4 0,6 0,8 1,0 1,2 1,4 1,6
All dimensions are in mm.
*Measured without air ducts mounted.**Measured with air ducts mounted.
736
650
FunctionThe CDT 40 is a robust, cost-effective and energy-efficient, reliable mobile de-humidifier. It works in accordance with the condensation principle. A fan draws the humid air into the dehumidifier and through an evaporator coil. When passing through the evaporator the air is cooled down to below its dew point temperature, and its content of water vapour is condensed into water, which is collected in the water container.
Applications• Damage service• Building drying• Water works• Dry storing
Dehumidifier• High capacity• Low energy consumption• Strong and robust cabinet of powder coated hot galvanized steel• Epoxy coated evaporator and condenser.• Adjustable handle• Plastic bumpers• Low weight• Stackable.• Large wheels
Water container• Water container with handles• Automatic stop when water container is full or removed.• Permanent drainage can be established with optional ½” hose connection• Condensate pump in a cassette as optional extra
Electronic control• Digital touchpad control panel with display• Accurate hour and kWh counter (reading)• RH and °C monitoring (reading)• RH setting• Easy fault-finding• Service monitoring function
DefrostingActive, demand-controlled defrosting which is activated through a tempera-ture sensor on the evaporator. Defrosting is done by means of hot refrigerant being fed through the evaporator.
CDT 40
CDT 40MOBILE DEHUMIDIFIER
FEATURES
MOBILE DEHUMIDIFIERS CDT
Digital touchpad control panel:1. On-off switch2. Reading of room temperature3. Indicator for normal operation (green lamp)4. Reading of RH value / setting of RH value5. Indicator for full water container (yellow lamp)6. Failure indicator (red lamp)7. Hour counter / setting of service intervals8. kWh counter
Specific energy consumption (SEC)• 0,50 kWh/l at 30°C & 80% RH• 0,66 kWh/l at 20°C & 60% RH
Accessories½” drain outletRemote hygrostatWall bracketDual voltage kitCondensate pump in a cassette(see separate data sheet)
Also available in this series:CDT 30CDT 30 SCDT 40 SCDT 60CDT 90(see separate data sheets)
Model CDT 40Operating range – humidity 40-100% RHOperating range – temperature 3-32°CAir volume 350 m³/hPower supply 230 V/50 HzMax. ampere consumption 3,6 AMax. power consumption 0,810 kWRefrigerant R 407CCompressor type RotarySound level (at 1 metre) 59 dB(A)Water container capacity 14 litresColour - water container and wheel cap RAL 7015Colour - front grille RAL 7044Colour - control panel and bumpers RAL 9005Protection class IP X4Filter PPI 15Wheel size Ø 250 mmWheel and water container material PPControl panel material ABSWeight 43 kg
dantherm.com
TECHNICAL DATA
CAPACITY CURVES
DIMENSIONS
MOBILE DEHUMIDIFIERS CDT
Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)
CDT 40 MK II
ohr
93699.24g
BEND RADII:
24-05-2012
SCALE: NOT TO SCALE 351191
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
PART NO REV.:
RE
V.:
PA
RT
NO
Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH) 351 191
only entended as a guide.
CDT 40 MK II
8
Sheetmetal flatstate is based on Dantherm A/S process equipment and is
table LZT 142 0001, category Surface appearance according to reference
ARE THE PROPERTY OF SAID COMPANY AND WILL BE PROTECTED BY PATENTS
THIS DRAWING IS FURNISHED WITH THE UNDERSTANDING THAT THE ESSENCE THERE OF WILL NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT WRITTEN AUTHORIZATION BY Dantherm A/S. ALL DESIGNS ORIGINATED BY Dantherm A/S
Linear dimensions without tolerances according to DS/EN 22768-1 mediumAngular dimensions without tolerances: ± 1°
740
825
540
545
Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)
CDT 40 MK II
ohr
93699.24g
BEND RADII:
24-05-2012
SCALE: NOT TO SCALE 351191
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
PART NO REV.:
RE
V.:
PA
RT
NO
Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH) 351 191
only entended as a guide.
CDT 40 MK II
8
Sheetmetal flatstate is based on Dantherm A/S process equipment and is
table LZT 142 0001, category Surface appearance according to reference
ARE THE PROPERTY OF SAID COMPANY AND WILL BE PROTECTED BY PATENTS
THIS DRAWING IS FURNISHED WITH THE UNDERSTANDING THAT THE ESSENCE THERE OF WILL NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT WRITTEN AUTHORIZATION BY Dantherm A/S. ALL DESIGNS ORIGINATED BY Dantherm A/S
Linear dimensions without tolerances according to DS/EN 22768-1 mediumAngular dimensions without tolerances: ± 1°
740
825
540
545
Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)
CDT 40 MK II
ohr
93699.24g
BEND RADII:
24-05-2012
SCALE: NOT TO SCALE 351191
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
PART NO REV.:
RE
V.:
PA
RT
NO
Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH) 351 191
only entended as a guide.
CDT 40 MK II
8
Sheetmetal flatstate is based on Dantherm A/S process equipment and is
table LZT 142 0001, category Surface appearance according to reference
ARE THE PROPERTY OF SAID COMPANY AND WILL BE PROTECTED BY PATENTS
THIS DRAWING IS FURNISHED WITH THE UNDERSTANDING THAT THE ESSENCE THERE OF WILL NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT WRITTEN AUTHORIZATION BY Dantherm A/S. ALL DESIGNS ORIGINATED BY Dantherm A/S
Linear dimensions without tolerances according to DS/EN 22768-1 mediumAngular dimensions without tolerances: ± 1°
740
825
540
545
0
5
10
15
20
25
30
35°C
L/H
40% 60% 80%
0 0,2 0,4 0,6 0,8 1,0 1,2 1,4 1,6 1,8
All dimensions are in mm.
823
736
539
542
FunctionThe CDT 40 S is a robust, cost-effective and energy-efficient, reliable mobile de-humidifier. It works in accordance with the condensation principle. A fan draws the humid air into the dehumidifier and through an evaporator coil. When passing through the evaporator the air is cooled down to below its dew point temperature, and its content of water vapour is condensed into water, which is collected in the water container.
Applications• Damage service• Building drying• Water works• Dry storing
Dehumidifier• High capacity• Low energy consumption• Strong and robust cabinet of powder coated hot galvanized steel• Epoxy coated evaporator and condenser.• Adjustable handle• Plastic bumpers• Low weight• Stackable.• Large wheels• On the back two Ø100 mm flex. air ducts may be connected
(max. length of 5 m) (accessory)• Built-in 1 kW heating element• Supplied with high pressure fan
Water container• Water container with handles• Automatic stop when water container is full or removed.• Permanent drainage can be established with optional ½” hose connection• Condensate pump in a cassette as optional extra
Electronic control• Digital touchpad control panel with display• Accurate hour and kWh counter (reading)• RH and °C monitoring (reading)• RH setting• Easy fault-finding• Service monitoring function
DefrostingActive, demand-controlled defrosting which is activated through a tempera-ture sensor on the evaporator. Defrosting is done by means of hot refrigerant being fed through the evaporator.
CDT 40 S
CDT 40 SMOBILE DEHUMIDIFIER
FEATURES
MOBILE DEHUMIDIFIERS CDT
Digital touchpad control panel:1. On-off switch2. Reading of room temperature3. Indicator for normal operation (green lamp)4. Reading of RH value / setting of RH value5. Indicator for full water container (yellow lamp)6. Failure indicator (red lamp)7. Hour counter / setting of service intervals8. kWh counter
Specific energy consumption (SEC)• 0,47 kWh/l at 30°C & 80% RH• 0,83 kWh/l at 20°C & 60% RH
Accessories½” drain outletRemote hygrostatWall bracketDual voltage kitCondensate pump in a cassetteFlex. air ducts Ø100 mm(see separate data sheet)
Also available in this series:CDT 30CDT 30 SCDT 40CDT 60CDT 90(see separate data sheets)
Model CDT 40 SOperating range – humidity 40-100% RHOperating range – temperature 3-32°CAir volume 560 m³/h*Power supply 230 V/50 HzMax. ampere consumption 3,7 AMax. power consumption with heating element 1,84 kWMax. power consumption without heating element 0,84 kWRefrigerant R 407cCompressor type RotarySound level (at 1 metre) 62 dB(A)**Water container capacity 14 litresColour - water container and wheel cap RAL 7015Colour - front grille RAL 7044Colour - control panel and bumpers RAL 9005Protection class IP X4Filter PPI 15Wheel size Ø 250 mmWheel and water container material PPControl panel material ABSWeight 46 kg
dantherm.com
TECHNICAL DATA
CAPACITY CURVES
DIMENSIONS
MOBILE DEHUMIDIFIERS CDT
Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)
CDT 40 S MK II
ohr
93418.55g
BEND RADII:
24-05-2012
SCALE: NOT TO SCALE 351192
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
PART NO REV.:
RE
V.:
PA
RT
NO
Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH) 351 192
only entended as a guide.
CDT 40 S MK II
8
Sheetmetal flatstate is based on Dantherm A/S process equipment and is
table LZT 142 0001, category Surface appearance according to reference
ARE THE PROPERTY OF SAID COMPANY AND WILL BE PROTECTED BY PATENTS
THIS DRAWING IS FURNISHED WITH THE UNDERSTANDING THAT THE ESSENCE THERE OF WILL NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT WRITTEN AUTHORIZATION BY Dantherm A/S. ALL DESIGNS ORIGINATED BY Dantherm A/S
Linear dimensions without tolerances according to DS/EN 22768-1 mediumAngular dimensions without tolerances: ± 1°
740
825
540
542
Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)
CDT 40 S MK II
ohr
93418.55g
BEND RADII:
24-05-2012
SCALE: NOT TO SCALE 351192
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
PART NO REV.:
RE
V.:
PA
RT
NO
Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH) 351 192
only entended as a guide.
CDT 40 S MK II
8
Sheetmetal flatstate is based on Dantherm A/S process equipment and is
table LZT 142 0001, category Surface appearance according to reference
ARE THE PROPERTY OF SAID COMPANY AND WILL BE PROTECTED BY PATENTS
THIS DRAWING IS FURNISHED WITH THE UNDERSTANDING THAT THE ESSENCE THERE OF WILL NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT WRITTEN AUTHORIZATION BY Dantherm A/S. ALL DESIGNS ORIGINATED BY Dantherm A/S
Linear dimensions without tolerances according to DS/EN 22768-1 mediumAngular dimensions without tolerances: ± 1°
740
825
540
542
Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)
CDT 40 S MK II
ohr
93418.55g
BEND RADII:
24-05-2012
SCALE: NOT TO SCALE 351192
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
PART NO REV.:
RE
V.:
PA
RT
NO
Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH) 351 192
only entended as a guide.
CDT 40 S MK II
8
Sheetmetal flatstate is based on Dantherm A/S process equipment and is
table LZT 142 0001, category Surface appearance according to reference
ARE THE PROPERTY OF SAID COMPANY AND WILL BE PROTECTED BY PATENTS
THIS DRAWING IS FURNISHED WITH THE UNDERSTANDING THAT THE ESSENCE THERE OF WILL NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT WRITTEN AUTHORIZATION BY Dantherm A/S. ALL DESIGNS ORIGINATED BY Dantherm A/S
Linear dimensions without tolerances according to DS/EN 22768-1 mediumAngular dimensions without tolerances: ± 1°
740
825
540
542
0
5
10
15
20
25
30
35°C
L/H
40% 60% 80%
0 0,2 0,4 0,6 0,8 1,0 1,2 1,4 1,6 1,8 2,0
All dimensions are in mm.
*Measured without air ducts mounted.**Measured with air ducts mounted.
823
736
539
FunctionThe CDT 60 is a robust, cost-effective and energy-efficient, reliable mobile de-humidifier. It works in accordance with the condensation principle. A fan draws the humid air into the dehumidifier and through an evaporator coil. When passing through the evaporator the air is cooled down to below its dew point temperature, and its content of water vapour is condensed into water, which is collected in the water container.
Applications• Damage service• Building drying• Water works• Dry storing
Dehumidifier• High capacity• Low energy consumption• Strong and robust cabinet of powder coated hot galvanized steel• Epoxy coated evaporator and condenser.• Adjustable handle• Plastic bumpers• Low weight• Stackable.• Large wheels
Water container• Water container with handles• Automatic stop when water container is full or removed.• Permanent drainage can be established with optional ½” hose connection• Condensate pump in a cassette as optional extra
Electronic control• Digital touchpad control panel with display• Accurate hour and kWh counter (reading)• RH and °C monitoring (reading)• RH setting• Easy fault-finding• Service monitoring function
DefrostingActive, demand-controlled defrosting which is activated through a tempera-ture sensor on the evaporator. Defrosting is done by means of hot refrigerant being fed through the evaporator.
CDT 60
CDT 60MOBILE DEHUMIDIFIER
FEATURES
MOBILE DEHUMIDIFIERS CDT
Digital touchpad control panel:1. On-off switch2. Reading of room temperature3. Indicator for normal operation (green lamp)4. Reading of RH value / setting of RH value5. Indicator for full water container (yellow lamp)6. Failure indicator (red lamp)7. Hour counter / setting of service intervals8. kWh counter
Specific energy consumption (SEC)• 0,43 kWh/l at 30°C & 80% RH• 0,67 kWh/l at 20°C & 60% RH
Accessories½” drain outletRemote hygrostatWall bracketDual voltage kitCondensate pump in a cassette(see separate data sheet)
Also available in this series:CDT 30CDT 30 SCDT 40CDT 40 SCDT 90(see separate data sheets)
Model CDT 60Operating range – humidity 40-100% RHOperating range – temperature 3-32°CAir volume 725 m³/hPower supply 230 V/50 HzMax. ampere consumption 4,9 AMax. power consumption 1,12 kWRefrigerant R 407cCompressor type RotarySound level (at 1 metre) 62 dB(A)Water container capacity 14 litresColour - water container and wheel cap RAL 7015Colour - front grille RAL 7044Colour - control panel and bumpers RAL 9005Protection class IP X4Filter PPI 15Wheel size Ø 250 mmWheel and water container material PPControl panel material ABSWeight 47 kg
dantherm.com
TECHNICAL DATA
CAPACITY CURVES
DIMENSIONS
MOBILE DEHUMIDIFIERS CDT
Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)only entended as a guide.
CDT 60 MK II
99141.12g
BEND RADII:
CDT 60 MK II
ohr
351193
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
PART NO REV.:
RE
V.:
PA
RT
NO
Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH)
25-05-2012
SCALE: NOT TO SCALE
351 193
8
Sheetmetal flatstate is based on Dantherm A/S process equipment and is
table LZT 142 0001, category Surface appearance according to reference
ARE THE PROPERTY OF SAID COMPANY AND WILL BE PROTECTED BY PATENTS
THIS DRAWING IS FURNISHED WITH THE UNDERSTANDING THAT THE ESSENCE THERE OF WILL NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT WRITTEN AUTHORIZATION BY Dantherm A/S. ALL DESIGNS ORIGINATED BY Dantherm A/S
Linear dimensions without tolerances according to DS/EN 22768-1 mediumAngular dimensions without tolerances: ± 1°
820
905
540
542
Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)only entended as a guide.
CDT 60 MK II
99141.12g
BEND RADII:
CDT 60 MK II
ohr
351193
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
PART NO REV.:
RE
V.:
PA
RT
NO
Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH)
25-05-2012
SCALE: NOT TO SCALE
351 193
8
Sheetmetal flatstate is based on Dantherm A/S process equipment and is
table LZT 142 0001, category Surface appearance according to reference
ARE THE PROPERTY OF SAID COMPANY AND WILL BE PROTECTED BY PATENTS
THIS DRAWING IS FURNISHED WITH THE UNDERSTANDING THAT THE ESSENCE THERE OF WILL NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT WRITTEN AUTHORIZATION BY Dantherm A/S. ALL DESIGNS ORIGINATED BY Dantherm A/S
Linear dimensions without tolerances according to DS/EN 22768-1 mediumAngular dimensions without tolerances: ± 1°
820
905
540
542
Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)only entended as a guide.
CDT 60 MK II
99141.12g
BEND RADII:
CDT 60 MK II
ohr
351193
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
PART NO REV.:
RE
V.:
PA
RT
NO
Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH)
25-05-2012
SCALE: NOT TO SCALE
351 193
8
Sheetmetal flatstate is based on Dantherm A/S process equipment and is
table LZT 142 0001, category Surface appearance according to reference
ARE THE PROPERTY OF SAID COMPANY AND WILL BE PROTECTED BY PATENTS
THIS DRAWING IS FURNISHED WITH THE UNDERSTANDING THAT THE ESSENCE THERE OF WILL NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT WRITTEN AUTHORIZATION BY Dantherm A/S. ALL DESIGNS ORIGINATED BY Dantherm A/S
Linear dimensions without tolerances according to DS/EN 22768-1 mediumAngular dimensions without tolerances: ± 1°
820
905
540
542
0
5
10
15
20
25
30
35° C
L/H
40% 60% 80%
0 0,5 1,0 1,5 2,0 2,5 3,0
All dimensions are in mm.
903
816
539
FunctionThe CDT 90 is a robust, cost-effective and energy-efficient, reliable mobile de-humidifier. It works in accordance with the condensation principle. A fan draws the humid air into the dehumidifier and through an evaporator coil. When passing through the evaporator the air is cooled down to below its dew point temperature, and its content of water vapour is condensed into water, which falls into the drip tray and then is led to the drain.
Applications• Damage service• Building drying• Water works• Dry storing
Dehumidifier• High capacity• Low energy consumption• Strong and robust cabinet of powder coated hot galvanized steel• Epoxy coated evaporator and condenser.• Adjustable handle• Plastic bumpers• Low weight• Large wheels
Water drain• Fitted with a drain outlet for connection to a ½” water hose
Electronic control• Digital touchpad control panel with display• Accurate hour and kWh counter (reading)• RH and °C monitoring (reading)• RH setting• Easy fault-finding• Service monitoring function
DefrostingActive, demand-controlled defrosting which is activated through a tempera-ture sensor on the evaporator. Defrosting is done by means of hot refrigerant being fed through the evaporator.
CDT 90
CDT 90MOBILE DEHUMIDIFIER
FEATURES
MOBILE DEHUMIDIFIERS CDT
Digital touchpad control panel:1. On-off switch2. Reading of room temperature3. Indicator for normal operation (green lamp)4. Reading of RH value / setting of RH value5. Indicator for full water container (yellow lamp)6. Failure indicator (red lamp)7. Hour counter / setting of service intervals8. kWh counter
Specific energy consumption (SEC)• 0,42 kWh/l at 30°C & 80% RH• 0,71 kWh/l at 20°C & 60% RH
AccessoriesRemote hygrostatDual voltage kit(see separate data sheet)
Also available in this series:CDT 30CDT 30 SCDT 40CDT 40 SCDT 60(see separate data sheets)
Model CDT 90Operating range – humidity 40-100% RHOperating range – temperature 3-32°CAir volume 1000 m³/hPower supply 230 V/50 HzMax. ampere consumption 7,2 AMax. power consumption 1,65 kWRefrigerant R 407cCompressor type RotarySound level (at 1 metre) 62 dB(A)Colour - wheel cap RAL 7015Colour - front grill RAL 7044Colour - control panel and bumpers RAL 9005Protection class IP X4Filter PPI 15Wheel size Ø 250 mmWheel material PPControl panel material ABSWeight 62 kg
dantherm.com
TECHNICAL DATA
CAPACITY CURVES
DIMENSIONS
MOBILE DEHUMIDIFIERS CDT
ohr
Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)
CDT 90 MK II
355066.95g
BEND RADII:
23-12-2011
SCALE: NOT TO SCALE 351194
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
PART NO REV.:
RE
V.:
PA
RT
NO
Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH) 351 194
only entended as a guide.
CDT 90 MK II
8
Sheetmetal flatstate is based on Dantherm A/S process equipment and is
table LZT 142 0001, category Surface appearance according to reference
ARE THE PROPERTY OF SAID COMPANY AND WILL BE PROTECTED BY PATENTS
THIS DRAWING IS FURNISHED WITH THE UNDERSTANDING THAT THE ESSENCE THERE OF WILL NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT WRITTEN AUTHORIZATION BY Dantherm A/S. ALL DESIGNS ORIGINATED BY Dantherm A/S
Linear dimensions without tolerances according to DS/EN 22768-1 mediumAngular dimensions without tolerances: ± 1°
895
980
593
650
ohr
Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)
CDT 90 MK II
355066.95g
BEND RADII:
23-12-2011
SCALE: NOT TO SCALE 351194
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
PART NO REV.:
RE
V.:
PA
RT
NO
Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH) 351 194
only entended as a guide.
CDT 90 MK II
8
Sheetmetal flatstate is based on Dantherm A/S process equipment and is
table LZT 142 0001, category Surface appearance according to reference
ARE THE PROPERTY OF SAID COMPANY AND WILL BE PROTECTED BY PATENTS
THIS DRAWING IS FURNISHED WITH THE UNDERSTANDING THAT THE ESSENCE THERE OF WILL NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT WRITTEN AUTHORIZATION BY Dantherm A/S. ALL DESIGNS ORIGINATED BY Dantherm A/S
Linear dimensions without tolerances according to DS/EN 22768-1 mediumAngular dimensions without tolerances: ± 1°
895
980
593
650
ohr
Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)
CDT 90 MK II
355066.95g
BEND RADII:
23-12-2011
SCALE: NOT TO SCALE 351194
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
PART NO REV.:
RE
V.:
PA
RT
NO
Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH) 351 194
only entended as a guide.
CDT 90 MK II
8
Sheetmetal flatstate is based on Dantherm A/S process equipment and is
table LZT 142 0001, category Surface appearance according to reference
ARE THE PROPERTY OF SAID COMPANY AND WILL BE PROTECTED BY PATENTS
THIS DRAWING IS FURNISHED WITH THE UNDERSTANDING THAT THE ESSENCE THERE OF WILL NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT WRITTEN AUTHORIZATION BY Dantherm A/S. ALL DESIGNS ORIGINATED BY Dantherm A/S
Linear dimensions without tolerances according to DS/EN 22768-1 mediumAngular dimensions without tolerances: ± 1°
895
980
593
650
0
5
10
15
20
25
30
35° C
L/H
40% 60% 80%
0 0,5 1,0 1,5 2,0 2,5 3,0 3,5 4,0 4,5
All dimensions are in mm.
977
894
593
ACCESSORIES CDT
MOBILE DEHUMIDIFIERS CDT
Illustration Accessory Description CDT-type DanthermNo.
Hygrostat When a hygrostat is connected the dehumidifier can operate continuously dependent on the rela-tive humidity in the room.
Two versions are available:
Hygrostat with 0,4 m cable, jack plug and fitting
Hygrostat with 3 m cable and jack plug
All
All
396242
396241
½” draining tap and screwed hose con-nector
Ball tap, brass screwed hose connector and clamp for mounting on the water container
All 396243
Condensate pump in a cassette
Cassette with builtin condensate pump CDT 30/30S
CDT 40/40S/60
075616
075617
Wall bracket Using the wall bracket the dehumidifier can be hung on the wall
CDT 30/30S
CDT 40/40S/60
396247
396248
Flexible air duct Ø100 mm with clamp
CDT 30S and CDT 40S are prepared for connection of two flexible air ducts
CDT 30S/CDT 40S
80100065(clamp:543620)
dantherm.com