Upload
dinhque
View
214
Download
1
Embed Size (px)
Citation preview
FunctionThe CDP 40 is an energy efficient and quiet pool dehumidifier. It works in ac-cordance with the condensation principle. A fan draws the humid air into the dehumidifier and through an evaporator coil. When passing through the evap-orator the air is cooled down to below its dew point temperature, and its con-tent of water vapour is condensed into water, which falls into the drip tray and then is led from the drip tray to a drain. The cold, dry air is then passed over the condenser coil where it is re-heated, before leaving the unit at a temperature, which is approx. 5°C higher than at the inlet.
Applications• Indoor swimming pools, private or hotels• Therapy pools• Spas• Gymnasias
CDP 40 SWIMMING POOL DEHUMIDIFIER
POOL DEHUMIDIFIERS CDP
FEATURES
Dehumidifier• Built into a strong and robust powder coated hot galvanized sheet metal
cabinet• Evaporator and condenser coils are epoxy-coated for high corrosion
resistance• Fixed to the wall by means of a wall mounting strip supplied with the unit• Condensate outlet located at the bottom. Outlet stub can be connected
to a ¾” hose• Outside connection to mains
Control• Built in electronic hygrostat and thermostat• Integrated ON/OFF control of humidity and temperature (electric or water
heating coils as accessories)• 0-VOLT connection for alarm• 230 V for control valve, exhaust fan and pump/boiler• RS 485 gate for BMS (Modbus)
DiodesBLUE: Power connected, standby modeGREEN: Compressor ON, deicingYELLOW: Remote pairing modeRED: Errors
DefrostingActive, demand-controlled defrosting is incorporated in the electronic control.
ServiceFor easy service the refrigerant circuit is supplied with a service valve. The PCB has a USB gate for history data logging for easy fault finding.
Model CDP 40Operating range – humidity 40 – 100 %RHOperating range – temperature 10 – 36°CAir volume 400 m3/hPower supply 1x230/50 V/HzMax. ampere consumption 3,8 AMax. power consumption 0,9 kWRefrigerant R407CQuantity of refrigerant 0,7 kgCompressor RotaryFan RadialSound level (at 1 metre) 46 dB(A)Weight 56,5 kgFilter G3 PPI 15Colour (Cabinet/Front) RAL 7035/9016Protection class IPX4Corrosion protection in accordance with EN/ISO 12944-2 C4
dantherm.com
TECHNICAL DATA
POOL DEHUMIDIFIERS CDP
CAPACITY CURVES
INSTALLATION
CDP 40, 50 and 70 are designed for installation in the pool hall.
0
5
10
15
20
25
30
35
40
0 0,5 1,0 1,5 2,0 2,5
Temp. oC
L/H
CDP 40
40% RH 60% RH 80% RH
Specific energy consumption (SEC): 0,47 kWh/l at 28°C & 60% RH
POOL DEHUMIDIFIERS CDP
DIMENSIONS CDP 40
AccessoriesWireless remote control DRC1Floor mounting kit Water heating coils Control valve for water heating coilsElectric heating coils Exhaust fans
dantherm.com
All dimensions are in mm.
Floor mounting kit
Drain outlet position
Recommended installation of CDP 40
Min
. 225
M
in. 2
25
727
g
SCALE: NOT TO SCALE
351 512
351512
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
PART NO REV.:
REV.:
PAR
TN
O
Sheetmetal flatstate is based on Dantherm Air Handling A/S process equipment and is only entended as a guide.
CDP Large
CDP Large
8
This Drawing is furnished with the understanding that the essence there of will not be reproduced in whole or in part without written authorization by Dantherm Air Handling A/S. All designs originated by Dantherm Air Handling A/S are the property of said Company and will be protected by Patents.
Surface appearance according to referencetable LZT 142 0001, category
Linear dimensions without tolerances according to DS/EN 22768-1 medium. Angular dimensions without tolerances: ± 1°
DETAIL ASCALE 1 : 2
A
table LZT 142 0001, category process equipment and is only entended as a guide.
CDP Large
CDP Large
8
property of said Company and will be protected by Patents.
Surface appearance according to reference
g
SCALE: NOT TO SCALE
351 512
351512
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
PART NO REV.:
REV.:
PAR
TN
O
Sheetmetal flatstate is based on Dantherm Air Handling A/S
REF.:
DATE:All designs originated by Dantherm Air Handling A/S are the
This Drawing is furnished with the understanding that the essence there of will not be reproduced in whole or in part without written authorization by Dantherm Air Handling A/S.
Linear dimensions without tolerances according to DS/EN 22768-1 medium. Angular dimensions without tolerances: ± 1°
CDP 50 - 1160
CDP 40 - 1010
CDP 70 - 1495
56,
4 430,2
315,6
769
,2
699
,9
326,1
Min
. 225
Min
. 225
727
430,2
56,4
g
SCALE: NOT TO SCALE
351 512
351512
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
PART NO REV.:
REV.:
PAR
TN
O
Sheetmetal flatstate is based on Dantherm Air Handling A/S process equipment and is only entended as a guide.
CDP Large
CDP Large
8
This Drawing is furnished with the understanding that the essence there of will not be reproduced in whole or in part without written authorization by Dantherm Air Handling A/S. All designs originated by Dantherm Air Handling A/S are the property of said Company and will be protected by Patents.
Surface appearance according to referencetable LZT 142 0001, category
Linear dimensions without tolerances according to DS/EN 22768-1 medium. Angular dimensions without tolerances: ± 1°
913
950
,5
950,
5
913
298
table LZT 142 0001, category process equipment and is only entended as a guide.
CDP Large
CDP Large
8
property of said Company and will be protected by Patents.
Surface appearance according to reference
g
SCALE: NOT TO SCALE
351 512
351512
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
PART NO REV.:
REV.:
PAR
TN
O
Sheetmetal flatstate is based on Dantherm Air Handling A/S
REF.:
DATE:All designs originated by Dantherm Air Handling A/S are the
This Drawing is furnished with the understanding that the essence there of will not be reproduced in whole or in part without written authorization by Dantherm Air Handling A/S.
Linear dimensions without tolerances according to DS/EN 22768-1 medium. Angular dimensions without tolerances: ± 1°
CDP 50 - 1160
CDP 40 - 1010
CDP 70 - 1495
56,
4 430,2
315,6
769
,2
699
,9
326,1
1010
769,
2
315,6
699,
9
326,1
FunctionThe CDP 50 is an energy efficient and quiet pool dehumidifier. It works in ac-cordance with the condensation principle. A fan draws the humid air into the dehumidifier and through an evaporator coil. When passing through the evap-orator the air is cooled down to below its dew point temperature, and its con-tent of water vapour is condensed into water, which falls into the drip tray and then is led from the drip tray to a drain. The cold, dry air is then passed over the condenser coil where it is re-heated, before leaving the unit at a temperature, which is approx. 5°C higher than at the inlet.
Applications:• Indoor swimming pools, private or hotels• Therapy pools• Spas• Gymnasias
POOL DEHUMIDIFIERS CDP
DiodesBLUE: Power connected, standby modeGREEN: Compressor ON, deicingYELLOW: Remote pairing modeRED: Errors
DefrostingActive, demand-controlled defrosting is incorporated in the electronic control.
ServiceFor easy service the refrigerant circuit is supplied with a service valve. The PCB has a USB gate for history data logging for easy fault finding.
CDP 50 SWIMMING POOL DEHUMIDIFIER
FEATURES
Dehumidifier• Built into a strong and robust powder coated hot galvanized sheet metal
cabinet• Evaporator and condenser coils are epoxy-coated for high corrosion
resistance• Fixed to the wall by means of a wall mounting strip supplied with the unit• Condensate outlet located at the bottom. Outlet stub can be connected
to a ¾” hose• Outside connection to mains
Control• Built in electronic hygrostat and thermostat• Integrated ON/OFF control of humidity and temperature (electric or water
heating coils as accessories)• 0-VOLT connection for alarm• 230 V for control valve, exhaust fan and pump/boiler• RS 485 gate for BMS (Modbus)
Model CDP 50Operating range – humidity 40 – 100 %RHOperating range – temperature 10 – 36°CAir volume 680 m3/hPower supply 1x230/50 V/HzMax. ampere consumption 6,6 AMax. power consumption 1,5 kWRefrigerant R407CQuantity of refrigerant 0,9 kgCompressor RotaryFan RadialSound level (at 1 metre) 47 dB(A)Weight 65 kgFilter G3 PPI 15Colour (Cabinet/Front) RAL 7035 / 9016Protection class IPX4Corrosion protection in accordance with EN/ISO 12944-2 C4
dantherm.com
TECHNICAL DATA
CAPACITY CURVES
INSTALLATION
POOL DEHUMIDIFIERS CDP
CDP 40, 50 and 70 are designed for installation in the pool hall.
0
5
10
15
20
25
30
35
40
0 0,5 1,0 1,5 2,0 2,5 3,0 3,5 4,0
Temp.
L/H
60% RH 80% RH
CDP 50
40% RH
Specific energy consumption (SEC): 0,48 kWh/l at 28°C & 60% RH
°C
POOL DEHUMIDIFIERS CDP
DIMENSIONS CDP 50
dantherm.com
All dimensions are in mm.
Floor mounting kit
Drain outlet position
Recommended installation of CDP 50
Min
. 225
M
in. 2
25
727
g
SCALE: NOT TO SCALE
351 512
351512
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
PART NO REV.:
REV.:
PAR
TN
O
Sheetmetal flatstate is based on Dantherm Air Handling A/S process equipment and is only entended as a guide.
CDP Large
CDP Large
8
This Drawing is furnished with the understanding that the essence there of will not be reproduced in whole or in part without written authorization by Dantherm Air Handling A/S. All designs originated by Dantherm Air Handling A/S are the property of said Company and will be protected by Patents.
Surface appearance according to referencetable LZT 142 0001, category
Linear dimensions without tolerances according to DS/EN 22768-1 medium. Angular dimensions without tolerances: ± 1°
DETAIL ASCALE 1 : 2
A
table LZT 142 0001, category process equipment and is only entended as a guide.
CDP Large
CDP Large
8
property of said Company and will be protected by Patents.
Surface appearance according to reference
g
SCALE: NOT TO SCALE
351 512
351512
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
PART NO REV.:
REV.:
PAR
TN
O
Sheetmetal flatstate is based on Dantherm Air Handling A/S
REF.:
DATE:All designs originated by Dantherm Air Handling A/S are the
This Drawing is furnished with the understanding that the essence there of will not be reproduced in whole or in part without written authorization by Dantherm Air Handling A/S.
Linear dimensions without tolerances according to DS/EN 22768-1 medium. Angular dimensions without tolerances: ± 1°
CDP 50 - 1160
CDP 40 - 1010
CDP 70 - 1495
56,
4 430,2
315,6
769
,2
699
,9
326,1
Min
. 225
Min
. 225
727
430,2
56,4
AccessoriesWireless remote control DRC1Floor mounting kit Water heating coils Control valve for water heating coilsElectric heating coils Exhaust fans
g
SCALE: NOT TO SCALE
351 512
351512
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
PART NO REV.:
REV.:
PAR
TN
O
Sheetmetal flatstate is based on Dantherm Air Handling A/S process equipment and is only entended as a guide.
CDP Large
CDP Large
8
This Drawing is furnished with the understanding that the essence there of will not be reproduced in whole or in part without written authorization by Dantherm Air Handling A/S. All designs originated by Dantherm Air Handling A/S are the property of said Company and will be protected by Patents.
Surface appearance according to referencetable LZT 142 0001, category
Linear dimensions without tolerances according to DS/EN 22768-1 medium. Angular dimensions without tolerances: ± 1°
913
950
,5
950,
5
913
298
table LZT 142 0001, category process equipment and is only entended as a guide.
CDP Large
CDP Large
8
property of said Company and will be protected by Patents.
Surface appearance according to reference
g
SCALE: NOT TO SCALE
351 512
351512
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
PART NO REV.:
REV.:
PAR
TN
O
Sheetmetal flatstate is based on Dantherm Air Handling A/S
REF.:
DATE:All designs originated by Dantherm Air Handling A/S are the
This Drawing is furnished with the understanding that the essence there of will not be reproduced in whole or in part without written authorization by Dantherm Air Handling A/S.
Linear dimensions without tolerances according to DS/EN 22768-1 medium. Angular dimensions without tolerances: ± 1°
CDP 50 - 1160
CDP 40 - 1010
CDP 70 - 1495
56,
4 430,2
315,6
769
,2
699
,9
326,1
1160
769,
2
315,6
699,
9
326,1
FunctionThe CDP 70 is an energy efficient and quiet pool dehumidifier. It works in ac-cordance with the condensation principle. A fan draws the humid air into the dehumidifier and through an evaporator coil. When passing through the evap-orator the air is cooled down to below its dew point temperature, and its con-tent of water vapour is condensed into water, which falls into the drip tray and then is led from the drip tray to a drain. The cold, dry air is then passed over the condenser coil where it is re-heated, before leaving the unit at a temperature, which is approx. 5°C higher than at the inlet.
Applications:• Indoor swimming pools, private or hotels• Therapy pools• Spas• Gymnasias
CDP 70 SWIMMING POOL DEHUMIDIFIER
POOL DEHUMIDIFIERS CDP
DiodesBLUE: Power connected, standby modeGREEN: Compressor ON, deicingYELLOW: Remote pairing modeRED: Errors
DefrostingActive, demand-controlled defrosting is incorporated in the electronic control.
ServiceFor easy service the refrigerant circuit is supplied with a service valve. The PCB has a USB gate for history data logging for easy fault finding.
FEATURES
Dehumidifier• Built into a strong and robust powder coated hot galvanized sheet metal
cabinet• Evaporator and condenser coils are epoxy-coated for high corrosion
resistance• Fixed to the wall by means of a wall mounting strip supplied with the unit• Condensate outlet located at the bottom. Outlet stub can be connected
to a ¾” hose• Outside connection to mains
Control• Built in electronic hygrostat and thermostat• Integrated ON/OFF control of humidity and temperature (electric or water
heating coils as accessories)• 0-VOLT connection for alarm• 230 V for control valve, exhaust fan and pump/boiler• RS 485 gate for BMS (Modbus)
Model CDP 70Operating range – humidity 40 – 100 %RHOperating range – temperature 10 – 36°CAir volume 900 m3/hPower supply 1x230/50 V/HzMax. ampere consumption 8 AMax. power consumption 1,8 kWRefrigerant R407CQuantity of refrigerant 1,2 kgCompressor RotaryFan RadialSound level (at 1 metre) 50 dB(A)Weight 75,5 kgFilter G3 PPI 15Colour (Cabinet/Front) RAL 7035 / 9016Protection class IPX4Corrosion protection in accordance with EN/ISO 12944-2 C4
dantherm.com
TECHNICAL DATA
CAPACITY CURVES
INSTALLATION
POOL DEHUMIDIFIERS CDP
CDP 40, 50 and 70 are designed for installation in the pool hall.
0
5
10
15
20
25
30
35
40
0 1 2 3 4 5 6
Temp.
L/H
CDP 70
40% RH 60% RH 80% RH
Specific energy consumption (SEC): 0,43 kWh/l at 28°C & 60% RH
°C
POOL DEHUMIDIFIERS CDP
DIMENSIONS CDP 70
AccessoriesWireless remote control DRC1Floor mounting kit Water heating coils Control valve for water heating coilsElectric heating coils Exhaust fans
dantherm.com
All dimensions are in mm.
Floor mounting kit
Drain outlet position
Recommended installation of CDP 70
Min
. 225
M
in. 2
25
727
g
SCALE: NOT TO SCALE
351 512
351512
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
PART NO REV.:
REV.:
PAR
TN
O
Sheetmetal flatstate is based on Dantherm Air Handling A/S process equipment and is only entended as a guide.
CDP Large
CDP Large
8
This Drawing is furnished with the understanding that the essence there of will not be reproduced in whole or in part without written authorization by Dantherm Air Handling A/S. All designs originated by Dantherm Air Handling A/S are the property of said Company and will be protected by Patents.
Surface appearance according to referencetable LZT 142 0001, category
Linear dimensions without tolerances according to DS/EN 22768-1 medium. Angular dimensions without tolerances: ± 1°
DETAIL ASCALE 1 : 2
A
Min
. 225
Min
. 225
727
table LZT 142 0001, category process equipment and is only entended as a guide.
CDP Large
CDP Large
8
property of said Company and will be protected by Patents.
Surface appearance according to reference
g
SCALE: NOT TO SCALE
351 512
351512
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
PART NO REV.:
REV.:
PAR
TN
O
Sheetmetal flatstate is based on Dantherm Air Handling A/S
REF.:
DATE:All designs originated by Dantherm Air Handling A/S are the
This Drawing is furnished with the understanding that the essence there of will not be reproduced in whole or in part without written authorization by Dantherm Air Handling A/S.
Linear dimensions without tolerances according to DS/EN 22768-1 medium. Angular dimensions without tolerances: ± 1°
CDP 50 - 1160
CDP 40 - 1010
CDP 70 - 1495
56,
4 430,2
315,6
769
,2
699
,9
326,1
430,2
56,4
g
SCALE: NOT TO SCALE
351 512
351512
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
PART NO REV.:
REV.:
PAR
TN
O
Sheetmetal flatstate is based on Dantherm Air Handling A/S process equipment and is only entended as a guide.
CDP Large
CDP Large
8
This Drawing is furnished with the understanding that the essence there of will not be reproduced in whole or in part without written authorization by Dantherm Air Handling A/S. All designs originated by Dantherm Air Handling A/S are the property of said Company and will be protected by Patents.
Surface appearance according to referencetable LZT 142 0001, category
Linear dimensions without tolerances according to DS/EN 22768-1 medium. Angular dimensions without tolerances: ± 1°
913
950
,5
950,
5
913
298
table LZT 142 0001, category process equipment and is only entended as a guide.
CDP Large
CDP Large
8
property of said Company and will be protected by Patents.
Surface appearance according to reference
g
SCALE: NOT TO SCALE
351 512
351512
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
PART NO REV.:
REV.:
PAR
TN
O
Sheetmetal flatstate is based on Dantherm Air Handling A/S
REF.:
DATE:All designs originated by Dantherm Air Handling A/S are the
This Drawing is furnished with the understanding that the essence there of will not be reproduced in whole or in part without written authorization by Dantherm Air Handling A/S.
Linear dimensions without tolerances according to DS/EN 22768-1 medium. Angular dimensions without tolerances: ± 1°
CDP 50 - 1160
CDP 40 - 1010
CDP 70 - 1495
56,
4 430,2
315,6
769
,2
699
,9
326,1
1495
769,
2
315,6
699,
9
326,1