CCIE Routing & Switching 400-101 Certification Exam Guide

Exam Code: 400-101

Pass CCIE Routing and Switching

By Using www.realbraindumps.com Study Material

http://www.realbraindumps.com/

Why Choose Us?

We Know There is a Question in Your

Mind that why we choose

www.realbraindumps.com to pass

our Certifications Exam….??? Simple

And Straight Answer of Your

Question is shown in the Figure or

Chart Shown Here:Realbraindumps

Guaranteed Success

24/7 customer support

Questions same like in the real

exam

Money Back

Guarantee

www.realbraindumps.com




Your Success is Guaranteed With Us

We assure you that if you use our

dumps for the preparations of your

Certifications Exams, then your

success is guaranteed. Because the

questions we provide are same like

in the real exam. So just visit us at

www.realbraindumps.com to pass

any certification exam with ease.

100% Correct

Answers

All Dumps Are Tested And Approved

Free Updates for 120

days

99.3% Exam Passing

Assurance

Just 1 day

study required

Dumps Are 100% Valid





The List of Vendors :

We Provide Study Material (Demos,Dumps,Questions &

Answers etc) For all most All the Vendors that exists in Certification Fields. The List of Those Vendors is

Displayed Here:




Cisco 400-101 Sample Questions

http://www.realbraindumps.com/400-101-braindumps.htmlComplete File is Here:

Question 1:

If you change the Spanning Tree Protocol from pvst to rapid-pvst, what is the effect on the interface Fa0/1port state?

A. It transitions to the listening state, and then the forwarding state.B. It transitions to the learning state and then the forwarding state.C. It transitions to the blocking state, then the learning state, and then the forwarding state.D. It transitions to the blocking state and then the forwarding state.

Answer: C


http://www.realbraindumps.com/400-101-braindumps.html



Question 2:

Which configuration is missing that would enable SSH access on a router that is running Cisco IOS XE Software?

A. int Gig0/0/0 management-interfaceB. class-map ssh-class match access-group protect-ssh policy-map control-plane-in class ssh-class police 80000 conform transmit exceed drop control-plane service-policy input control plane-inC. control-plane host management-interface GigabitEthernet0/0/0 allow sshD. interface Gig0/0/0 ip access-group protect-ssh in

Answer: C





Question 3:

ICMP Echo requests from host A are not reaching the intended destination on host B.What is the problem?

A. The ICMP payload is malformed.B. The ICMP Identifier (BE) is invalid.C. The negotiation of the connection failed.D. The packet is dropped at the next hop.E. The link is congested.

Answer: D





Question 4:

Which statement is true?

A. It is impossible for the destination interface to equal the source interface..B. NAT on a stick is performed on interface Et0/0.C. There is a potential routing loop.D. This output represents a UDP flow or a TCP flow.

Answer: C





Question 5:

Which action will solve the error state of this interface when connecting a host behind a Cisco IP phone?

A. Configure dot1x-port control auto on this interface.B. Enable errdisable recovery for security violation errors.C. Enable port security on this interface.D. Configure multidomain authentication on this interface.

Answer: D





Question 6:

While troubleshooting high CPU utilization on one of your Cisco Catalyst switches, you find that the issue is due to excessive flooding that is caused by STP. What can you do to prevent this issue from happening again?

A. Disable STP completely on the switch.B. Change the STP version to RSTP.C. Configure PortFast on port-channel 1.D. Configure UplinkFast on the switch.E. Configure PortFast

Answer: E





Question 7:

While troubleshooting high CPU utilization of a Cisco Catalyst 4500 Series Switch, you notice the error message that is shown in the exhibit in the log file.What can be the cause of this issue, and how can it be prevented?

A. The hardware routing table is full. Redistribute from BGP into IGP.B. The software routing table is full. Redistribute from BGP into IGP.C. The hardware routing table is full.Reducethe number of routes in the routing table.D. The software routing table is full. Reduce the number of routes in the routing table.

Answer: C





Question 8:

All switches have default bridge priorities, and originate BPDUs with MAC addresses as indicated. The numbers shown are STP link metrics.Which two ports are forwarding traffic after STP converges? (Choose two.)

A. The port connecting switch SWD with switch SWE.B. The port connecting switch SWG with switch SWF.C. The port connecting switch SWC with switch SWE.D. The port connecting switch SWB with switch SWC.

Answer: C,D





Question 9:

Which three statements about the output are true? (Choose three.)

A. An mrouter port can be learned by receiving a PIM hello packet from a multicast router.B. This switch is configured as a multicast router.C. Gi2/0/1 is a trunk link that connects to a multicast router.D. An mrouter port is learned when a multicast data stream is received on that port from a multicast router.

Answer: A,B,C,





Question 10:

Which technology does the use of bi-directional BPDUs on all ports in the topology support?

A. RSTP.B. MST.C. Bridge Assurance.D. Loop Guard.E. Root GuardF. UDLD

Answer: C



Our Customers Views Demonsstrate Our Performance

Hi this is Findlay Ian. I was worried about my exam and I was thinking what should I do now. Then my best friend John I lham recommended me this website and he said I am sure you will pass your exam if you will follow their braindumps.

My Name is Lara Dwayne I Used the Braindumps of www.realbraindumps.comThey are providing 100% Correct Dumps. I passed My Exam with 950/1000 marks. Thank you realbraindumps.

We Build Our Customer’s Trust

www.realbraindumps.com The Name of Trust


Documents

CCIE Routing & Switching 400-101 Certification Exam Guide