USER’S MANUAL

SPACE

CC-1152ENG-03

1

Important Safety Instructions

Before installing the unit, please read and follow the instructions provided in the Installation Manual included in this kit.

Before operating the unit, please read and follow the instructions provided in this User´s Manual thoroughly and save it for future reference.

WARNING - To reduce the risk of fire or electric shock:

install in accordance with the manufacturer’s instructions

do not expose this apparatus to water dripping or splashing

do not use this product near water

do not attempt to disassemble this unit

do not block any ventilation openings

do not install near any heat sources such as radiators, stoves or other equipment that produce heat.

You are cautioned that any changes or modifications not expressly mentioned in this manual could affect the normal operation of this equipment.

This product has been designed and tested to provide reasonable protection against harmful interference in residential installation. However there is no guarantee that interference will not affect in a particular installation. In these cases, reorient the receiving antenna, try to increase the separation between the equipment and the source of interference and/or connect the equipment into an outlet on a circuit different from that to which the source of interference is connected.

The entire risk of the installation, use, results and performance are borne by you.

When a socket plug, or a device connector is used as a mechanism to disconnect from the electrical mains, the mechanism must be easily accessible at all times. Protect the power cord from being walked on or pinched particularly at plugs and the point where they exit from the apparatus.

Only use attachments/accessories specified by the manufacturer.

Use a certified technician for installation, repair and/or maintenance of this equipment and comply with all the regulations in force in each country. Servicing maybe required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to water dripping or splashing, does not operate normally, or has been dropped.

To change the batteries remove the cover by pressing on the tab while lifting the cover. Use batteries type AA 1,5V. Do not discard used batteries with household waste.

1. Introduction

2. General Operating Notes

3. Operating Audio Functions

7. Selecting Turn-On Mode

4. Operating the FM Tuner

5. Operating the wireless accessory KBSOUND

®DOCK

Quick Reference Guide

Table of Contents

CAUTION

DO NOT OPENRISK OF ELECTRIC SHOCK !

3

5

6

7

10

11

2

15

16

6. Operating the wireless accessory® ®

KBSOUND Bluetooth

8. Technical specifications

CC-1152ENG-03

2

Delete individual FM tuning pre-sets

Delete all FM tuning pre-sets

Store all FM stations detected

Store individual FM station pre-sets

Store “IDEAL” setting

Store turn-on mode (on/off)

Quick Reference Guide

Automatic FM station scan

Directly keying FM station frequency (e.g. 95.8 MHz)

Numeric keypad

Play/pause for iPod® playing list

Clear

Audio level adjustmentvolume/bass/treble/balance/loudness

Select +/- keys functionvolume/bass/treble/balance/loudness

FM Forced Mono

On/off

Step forward and back for iPod® playing list.

FM/DAB memory pre-sets

1”

”IDEAL” mode

Select sound source

® KBSOUND DOCK or Bluetooth link

Program MONO for all sound sources

Automatic FM station search sensitivity

To illustrate that an operation requires holding down a key on the remote control for a specific amount of time, the symbol will appear in the manual next to the key. The screen will display the symbol.F

F

2”

6”

2”

2”

2”

6”

6”

FM SENS 1-2-3

2”

6”

KBSOUND XX

6”

Save the kit numeric identification forBluetooth pairing

DAB iPOD

AUDIO IN

KBSOUND XXFM SENS 1-2-3

UPDATE DAB

CC-1152ENG-03

KBSOUND

The KBSOUND

KBSOUND

KBSOUND

® iSelect is a sound device specially designed for quick and easy installation. It fits discreetly into the decor of your kitchen, bathroom or

anywhere in your home.

® iSelect Kit comprises:

= Electronic module with built-in FM tuner and power supply.

41,5W + 1,5W stereo audio output.

= Two 2.5” or two 5" loudspeakers.

= Remote control with the following functions:

4Volume, bass, treble and balance control.4'Forced Mono' function.4FM and RDS information..4Ability to directly key-in desired station frequency.4Ability to automatically store into memory stations received with the best reception. 430 memory pre-sets.4“Intelligent” loudness: automatic adjustment to the volume level.

® When connected with the wireless DOCK Accessory (not included in this kit), the user has two additional sound sources: the iPod/iPhone

and an external sound source using a 3,5mm jack input.When connected with the (not included in this kit),

®

iSelect

® ® wireless KBSOUND Bluetooth Accessory allows the user to listen to the music stored in any device

that has the ability to transmit via Bluetooth.

The components supplied in this kit are for installation and use in the manner and for the purpose described in the Installation Manual and the User Manual. The installation must also comply with each country's current regulations. This manual assumes that the

unit has been installed following the instructions provided in the Installation Sheet included in this kit.

3

1. Introduction

CC-1152ENG-03

CC-1152ENG-03

KBSOUND

The KBSOUND

KBSOUND

KBSOUND

KBSOUND

® SPACE is a sound device specially designed for quick and easy installation. Is our new custom made audio solution. It´s open ended

allowing you to choose your loudspeakers and amplifiers tu fulfill the specific design requirements of your dream project with superb sound.

® SPACE Kit comprises:

= Electronic module with built-in FM tuner, includes terminals to allow connecting external amplifier, improve wiring design and ®connecting terminals to facilitate easy installation, design to insert the Radio Frequency device to allow integration with the

DOCK and the

= Infrared reciever / transmiter

= Remote control with the following functions:4Volume, bass, treble and balance control.4'Forced Mono' function.4FM and RDS information..4Ability to directly key-in desired station frequency.4Ability to automatically store into memory stations received with the best reception. 430 memory pre-sets.4“Intelligent” loudness: automatic adjustment to the volume level.

® When connected with the wireless DOCK Accessory (not included in this kit), the user has two additional sound sources: the iPod/iPhone

and an external sound source using a 3,5mm jack input.When connected with the (not included in this kit),

®

SPACE

® ® KBSOUND Bluetooth Accessory.

® ® wireless KBSOUND Bluetooth Accessory allows the user to listen to the music stored in any device

that has the ability to transmit via Bluetooth.

The components supplied in this kit are for installation and use in the manner and for the purpose described in the Installation Manual and the User Manual. The installation must also comply with each country's current regulations. This manual assumes that the

unit has been installed following the instructions provided in the Installation Sheet included in this kit.

4

5

1.- None of the functions (except ON/OFF) work unless the remote control is in “on” mode.

Once the KBSOUND or SPACE is connected to the mains, it will remain powered even it is in OFF state. That means that the OFF state (as indicated in this manual) really means a “standby” state.2.- ®

iSelect

beep

5m

The KBSOUND or SPACE will turn on with the

audio and station frequency settings saved as “ideal”

mode settings (see chapters 3 and 6) when the unit is

connected to a power supply.

When switched off and on while connected to the

power supply, the audio and station frequency settings

will be as when the unit was switched off with the remote

control ON/OFF key

® iSelect

2. General Operating Notes

DAB

iPOD

AUDIO IN

3.-

4.- The remote control unit exchanges information (transmits and receives data) by means of the transmission-reception capsule. If at any time there is a failure in the communication, the screen will display the symbol. In the event of this occurring, point the remote control to the transmission-reception capsule at a straight-line distance of no greater than 5 meters.

5.- The remote control display will automatically turn off when there has been no keying activity for more than a few seconds, ensuring more efficient battery usage. To view the display information at any time, point the remote control to the transmission-reception capsule and press the key of the selected sound source at this time

A short BEEP sound signal indicates that the data has been received

AUDIO INiPOD

CC-1152ENG-03

6

Key Sequence Display

Increase/decrease in the volume level: The LED will flash to indicate the desired change in volume.

Increase/decrease in bass/treble levels: The LED will flash to indicate the desired change in the bass/treble levels.

Loudness: It reinforces the bass level in terms of the volume level, assuming a greater backing at a lower volume and a lesser backing at a higher volume.

Mono/stereo reception: When activated, this feature allows the FM stations to be received in stereo. When deleted this feature only allows for mono reception.

Note: If the electronic module´s configuration is mono, the signal will always be received in mono even if the signal received by the antenna is in stereo.

If the electronic module is off, a brief press on the ON/OFF key will turn on the unit .

When the electronic module is off, the LED will be OFF.The LED will display the word “ON”

3. Operating Audio Functions

on

vol 58

BAS+06

LD on

STEREO

IDEAL

IDEAL2’’"IDEAL" mode of operation: To program your "IDEAL" mode of operation, select the sound source

(FM, iPod, Audio In) and desired levels of volume, bass, treble and loudness. Also, if your choice is FM, select your favorite station. Then hold down the IDEAL key for 2 seconds.

Then, this "IDEAL" mode can be instantly accessed by simply pressing the IDEAL key on the remote control.

CC-1152ENG-03

7

Key Sequence Display

To directly key-in an FM station frequency, sequentially dial the numeric keys of the station frequency then press the FM key. For example, to select 94.7, press 9 4 7 FM.

Note: A station frequency can be keyed-in as either 94.7 (9 4 7 FM) or as 94.70 (9 4 7 0 FM)

To clear a digit and start a different frequency, press the C key

and then begin keying-in of the desired frequency

4.2 Direct Key-in of Station Frequency

While the search is taking place, the word “SCAN” will appear on the display screen.

The screen will duly display the station frequency of the next station found.

4.1 Station Scan

4. Operating the FM Tuner

94.70

94.70

FM

FM

SCAN

102.50FM

1”

CC-1152ENG-03

Key Sequence Display

4.4 Storing and Clearing Station Frequencies Manually

To store a station, tune to the station (see Chapters 4.1. Station Search and 4.2. Direct key-in of Station Frequency).

Hold down the 9 key for 2 seconds. The station tuned at that time will be stored in the memory.

To delete a station from the memory, select the station and hold down the 7 key for 2 seconds. The station will be deleted from the memory.

The UP/DOWN keys allow you to scroll through the stations stored in the memory (see Chapters 4.4 and 4.5, Storing and Clearing Stations in Memory).

When stations are stored in the memory they are sorted in ascending order; that is, beginning with 87.5 and ending with 108.0.

The screen will display the frequency of the station stored in that memory pre-set.

4.3 Tuning to FM Memory Pre-Sets

MEM 07

DEL MEM

MEM 19

102.50FM

94.70FM

94.70FM

2’’

2’’

8

CC-1152ENG-03

Key Sequence Display

To activate the clearing station frequencies automatically process for all the memory slots, hold down 4 key for 6 seconds.

To activate the storing station frequencies automatically process, hold down key 6 for 6 seconds.

When the automatic programming begins the screen will display the word “AUTO”.

The electronic module will store into the memory the stations that are received with the best reception, sequentially from lowest frequency (87.5 MHz) to highest frequency (108.0 MHz).

The system will use all the memory slots available, reaching a maximum of 30.

The process can take a few moments. Once the scan has been completed or once the maximum number of memory slots has been used, the process ends and a BEEP signal

sounds.

4.5 Storing and Clearing Station Frequencies Automatically

To adjust the automatic station search sensitivity (see 4.1. Station Search), select a value between 1 (minimum) and 3 (maximum) and press key FM

SEN for 2 seconds

4.6 Adjusting Station Search Sensitivity

DEL ALL

AUTO

beep

6’’

6’’

SENS 1FM SENS 1-2-3FM SENS 1-2-3

2’’

2’’

2’’

FM SENS 1-2-3

FM SENS 1-2-3

SENS 2

SENS 3

9

CC-1152ENG-03

105. Operating the ®

KBSOUND DOCK

wireless accessory

Press key 5 for 6 seconds. Speaker led will flash in blue.

Power the Dock. Press the LINK key at the back of the Dock for 6 seconds. The Dock

led will flash in blue.

After a few seconds both leds will stop flashing and the Dock and the

KBSOUND SPACE are linked.

The iPOD key on the remote control selects the iPod® from the Wireless Dock as the audio source input. When playing

the Dock led will be green.

To play/pause the iPod®, use the key:

To step forward or back the iPod´s playing list, use the keys:

The Audio-in key on the remote control allows you to select the external audio

source that is connected by a 3,5mm jack to the Dock. When playing the Dock led

will be blue.

® iSelect or

Key Sequence DisplayThese functions are available only when

the KBSOUND accesory is connected.® DOCK

AUDIO IN

6”

6”

AUDIO IN

iPODIPOD

The wireless KBSOUND

Accessory for use with the KBSOUND 2,5" or 5" and SPACE allows you to enjoy and listen to your music from all models of iPhone and iPod, and any other external sound source that can be connected to the Dock using a 3,5mm jack input.

When the Dock is powered from the external power supply, it recharges the iPod/iPhone.IMPORTANT: use only the power supply supplied with the KBSOUND .

When the Dock is not connected to an external power supply it will be powered from the connected iPod/iPhone. In this case, the external audio source AUDIO IN is not available.

® DOCK

® iSelect

® DOCK

® the KBSOUND DOCK can be linked

® ONLY WITH ONE KBSOUND iSelect

or SPACE at any one time

CC-1152ENG-03

CC-1152ENG-03

11

Key sequence

Display

® ® The KBSOUND Bluetooth wireless accessory allows you to listen to the

music stored in any device that has the ability to transmit via Bluetooth ® ®

through the KBSOUND iSelect 2.5", KBSOUND iSelect 5" or ® ®

KBSOUND SPACE kits. (KBSOUND Bluetooth option).

6. Operating the wireless accessory

® ® KBSOUND Bluetooth

05

6”

KBsound XX

® IMPORTANT: Before linking the KBSOUND Bluetooth option a ® numeric address must be assigned to each KBSOUND kit installed

(See Chapter 6.2).

Several kits in the same house can be distinguished by assigning them a different identification number such as KBsound 00 or 01, 02 etc.

KB-05

® ® Features available ONLY when the KBSOUND Bluetooth accessory is connected

6.1.- Assign a numeric address to your ® ® KBSOUND Bluetooth option

iPODBTSelect Bluetooth key.

Dial the two digits that identify the KBsound kit such as “05" on the Remote Control.

Then press the 2 key for aproximately 5 seconds.

A confirmation beep will be heard through the speaker to indicate that the identifier has

KBsound00 KBsound01 KBsound02

KBsound03 KBsound04 KBsound05

beep

From this moment the identifier of that kit becomes KBsound 05.

Repeat this procedure for all kits you have installed in your home, taking care of choosing different numbers for each one.

IMPORTANT: before you begin make sure that the Bluetooth device from which you want to stream the music has the A2DP and AVRCP profiles.

CC-1152ENG-03

6.2.- Pairing (linking) a new Bluetooth device

Before being able to stream music from ®

a Bluetooth device to our KBSOUND kits it is necessary to link the ® Bluetooth accessory. This operation

must be carried out only once with each device.

Make sure that during the entire operation there is only one Bluetooth

device within the range of coverage of ® ®

the KBSOUND Bluetooth option.

The Remote Control must be pointing directly at the IR receiver of the

® ® KBSOUND Bluetooth option.

Select the Bluetooth key option.

Press the 5 key on the Remote Control for aproximately 10 seconds. “Link” will

appear in the display.

The IR led will flash in blue, and will remain in this state until the linking

operation is completed, or a maximum of 3 minutes.

Key Sequence

Display

Access the Bluetooth menu of your device

In the device select the KBsoundXX (00,01,02...) option.

Check that the code indicated on the device matches the code displayed

on the Remote Control.

Note: To get this code the Remote Control must be pointing directly at

the IR receiver.

The linking process will be carried out successfully when the IR blue led

stops flashing and “connected” appears in the display of the

Bluetooth device.

Some Bluetooth devices may optionally request a password to

confirm the link. In such cases, dial 0000.

iPODBT

6”

DISCONNECT LINK

048233

DAB

iPOD

AUDIO IN

DAB

iPOD

AUDIO IN

12

CC-1152ENG-03

6.3.- Transmit audio to a ® ® KBSOUND Bluetooth option from multiple Bluetooth devices

If you want to transmit audio from a different Bluetooth device, press the 5 key on the

Remote Control for 6 seconds, after which the ® ®

KBSOUND Bluetooth option will be freed from any previous pairing.

Activate the Bluetooth of the new device you wish to connect with and then select the

® ® KBSOUND Bluetooth option with which

you wish to link (e.g. KBsound 01).

The pairing will have been carried out successfully when the IR blue led stops

flashing.

Make sure that during the entire operation the Remote Control is

pointing directly at the IR ®

receiver of the KBSOUND

® Bluetooth and the Bluetooth device is within the range of

coverage.

Select the Bluetooth key on the Remote Control.

The kit searches for the last Bluetooth device with which it

was paired and, if found within its range of coverage, it will

continue to be paired automatically.

Key Sequence

Display

iPOD

6”

BT

Key Sequence

Display®

Several Bluetooth devices can share the same KBSOUND

® Bluetooth option, although only one can transmit audio at any time.

To make this possible, it is necessary to have made the link of all ® ®

Bluetooth devices with the KBSOUND Bluetooth option (see chapter 6.2)

DAB

iPOD

AUDIO IN

From the Remote Control you can select the options PLAY /PAUSE by pressing

the button

Go forward and backward through the music list

pressing the keys

13

CC-1152ENG-03

6.4.- Transmit audio from one device to several ® ® KBSOUND Bluetooth options

® ® If there are several KBSOUND Bluetooth options in your installation, you will be able to transmit your music to any of them interchangeably from the

® ® same Bluetooth mobile device. Please note that only one KBSOUND Bluetooth option can receive the audio signal at any time.

® ® To make this possible, it is necessary to have made the numeric identification of each KBSOUND Bluetooth option. (see chapter 6.1).

® ® It is also necessary that the Bluetooth mobile device has been linked with each of the KBSOUND Bluetooth options in the installation

(see chapter 6.2).

Select the Bluetooth option with the Remote Control of the® ®

KBSOUND Bluetooth option that you wish to use at that moment.

® ® Select in the Bluetooth device the KBSOUND Bluetooth option you wish to pair:

KBsound00, KBsound01, KBsound02, etc.

NOTE: Be careful, the menus on your Bluetooth device can vary between manufacturers.As a result, strictly follow their instructions.

Key Sequences

Display

iPODBT

KBsound 01

KBsound 02

KBsound 03

KBsound00 KBsound01 KBsound02

14

15

If the Turn-On mode is set to “on” in this state, when

power is fed to the unit, it will turn on in “ideal” mode (see

Chapter 3).

If the Turn-On mode is set to “off”, when power is fed to the unit, it will

turn on in “off” mode.

This function is designed for use in the event that the KBSOUND or SPACE power supply is fed by a specifically designated switch. In this case, the automatic activation mode must be programmed in order to automatically turn on KBSOUND or SPACE unit when the switch is activated. These steps must be followed:

® iSelect

® iSelect

1. Supply power to the KBSOUND or SPACE unit by turning on the switch. The KBSOUND or SPACE unit will flicker a couple of times and turn off.

2. Turn on the KBSOUND or SPACE unit using the remote control (ON/OFF key).

3. With the KBSOUND or SPACE unit turned on, keep the ON/OFF key pressed down for 2 seconds.

® iSelect

® iSelect

® iSelect

® iSelect

Key Sequence Display

7. Selecting Turn-On Mode

AUTO x

2’’

2’’

CC-1152ENG-03

CC-1152ENG-03

168. Technical specifications

525x1 , 52592 MIN NORMAL MAX NOTAS

Measurements 110x27,75x110 mm ref.525x1 (width x height x depth)

54,8x37x20 mm ref.52592 (width x height x depth)

Voltage 5 Vdc ref.525x1

Consumption demand 10 W ref.525x1

Input signal 350 mVrms jack 3,5mm

Input impedance 50 Kohms jack 3,5mm

Wireless transceiver RF 2,4 GHz

Power RF 10 mWeirp

Antenna RF integral ref. 525x1

2,5 dB ref.52592 (SMA connector)

52391/92 , 52398/93 MIN NORMAL MAX COMMENTS

Measurements 200x53x56 mm

Voltage 185 230 265 Vac 50Hz, terminal F,N (ref.52391,52398)

90 120 140 Vac 50/60Hz, terminal F,N (ref.52392,52393)

Consumption demand 10 W terminals F,N

Output signal (16 ohms) 1,5 W terminals L,R

Passband 45 20.000 Hz

Aux.amplifier switch on signal 12 14 Vdc terminals 62, 4 (ref.52398/93)

Distortion 0,1 %

Left/right channel separation 58 dB

FM Frequency range 87,5 108 MHz

FM antenna impedance 75 ohms RF connector

FM antenna sensitivity 1,7 3,5 uV

FM tuner distortion 0,1 0,5 %

Number of FM station pre-sets 30

52593 MIN NORMAL MAX NOTES

Measurements 54,8x37x20 mm width x height x depth

Alimentación 3,3V Vdc internal connector

Consumo 0,1 W

Bluetooth spec.

Wireless transceiver RF 2,4 GHz

Power RF 10 mWeirp

Antenna RF 2,5 dB SMA connector

Range 5 m

Class2 BT2.1 + EDR

A2DP 1.2

AVRCP 1.4

525x1 , 52592 MIN NORMAL MAX NOTAS

Measurements 110x27,75x110 mm ref.525x1 (width x height x depth)

54,8x37x20 mm ref.52592 (width x height x depth)

Voltage 5 Vdc ref.525x1

Consumption demand 10 W ref.525x1

0,1 W ref.52592

Input signal 350 mVrms jack 3,5mm

Input impedance 50 Kohms jack 3,5mm

Wireless transceiver RF 2,4 GHz

Power RF 10 mWeirp

Antenna RF integral ref. 525x1

2,5 dB ref.52592 (SMA connector)

Range 5 m

64460058

Electrónica Integral de Sonido S.A. is not responsible for any error or omissions that may appear in this manual, and reserves the right to make changes without prior notice. iPod and iPhone is trademark of Apple Inc. registered in teh U.S. and other countries. "Made for iPod" and "Made for iPhone" means that an electronic accessory has been designed to connect specifically to iPod and iPhone and has been certified by Electrónica Integral de Sonido S.A. to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accesory with iPhone may affect wireless performance.

AENOR

RegistradaEmpresa

ER-0634/1998

Polígono Malpica Calle F OesteGrupo Gregorio Quejido, 87-8850016 Zaragoza (SPAIN)Tel.: 34 976 465 550Fax: 34 976 465 559comercial@eissound.com

www.eissound.com

CC-1152ENG-03