Upload
nguyenkiet
View
326
Download
15
Embed Size (px)
Citation preview
Caterpillar Electronic Technician 2012A v1.0 Product Status Report
3/17/2013 9:18 AM
Product Status Report
C6.4 320D (GDC40776)
Logged Diagnostic Codes [Diagnostic Clock = 6930.8208 hours] - C6.4 320D (GDC40776)
Logged Event Codes [Diagnostic Clock = 6930.8208 hours] - C6.4 320D (GDC40776)
Parameter Value
Product ID GKS00234
Equipment ID GKS00234
Comments
Parameter Value
Equipment ID GKS00234
Engine Serial Number GDC40776
ECM Part Number 3317539-00
ECM Serial Number 22106011MB
Software Group Part Number 3282883-00
Software Group Release Date 2008
Software Group Description MHI 320D A4E2i2
Active Event Codes Present Unavailable
Code Description Occ. First Last
No Logged Diagnostic Codes
Code Description Occ. First Last
E198 (2) Low Fuel Pressure 6 6930 6930
E265 (3) User Defined Shutdown 1 6880 6880
Page 1 of 30
3/17/2013file://C:\Documents and Settings\All Users\Application Data\Caterpillar\Electronic Techni...
Active Diagnostic Codes - C6.4 320D (GDC40776)
Active Event Codes - C6.4 320D (GDC40776)
Current Totals - C6.4 320D (GDC40776)
Configuration - C6.4 320D (GDC40776)
Code Description
No Active Codes
Code Description
No Active Events
Description Value Unit
Total Operating Hours 6931 hours
Total Fuel 28806 gal
Total Idle Time 2211:54 hours
Total Idle Fuel 2321 gal
Percentage Idle Time 31.90 %
Average Fuel Rate 4.16 gal/h
Description Value Unit
Equipment ID GKS00234
Engine Serial Number GDC40776
ECM Part Number 3317539-00
ECM Serial Number 22106011MB
Software Group Part Number 3282883-00
Software Group Release Date 2008
Software Group Description MHI 320D A4E2i2
Rated Power 157 hp at 1800 rpm
Rated Peak Torque 482 lb-ft at 1400 rpm
Top Engine Speed Range 1980 - 1980 rpm
Test Spec
FLS -2
FTS -9
Security System Immobilizer Installation Status Disabled or Not Installed
Total Tattletale 1
Page 2 of 30
3/17/2013file://C:\Documents and Settings\All Users\Application Data\Caterpillar\Electronic Techni...
Injector Trim Calibration - C6.4 320D (GDC40776)
Machine Control 320D/323D
Logged Diagnostic Codes [Diagnostic Clock = 6928 hours] - Machine Control 320D/323D
Logged Event Codes [Diagnostic Clock = 6928 hours] - Machine Control 320D/323D
Active Diagnostic Codes - Machine Control 320D/323D
Injector Serial Number File Version
Injector1 000000002S0117710965 1
Injector2 000000002S011771227E 1
Injector3 000000002S0117710541 1
Injector4 000000002S0117711970 1
Injector5 000000002S011771175A 1
Injector6 000000002S0117710648 1
Parameter Value
Product ID GKS00234
ECM Part Number 2218874-07
ECM Serial Number 01430781EM
Software Group Part Number 3495439-00
Software Group Release Date OCT2009
Software Group Description 320D/323D HEX CONTROL
Active Diagnostic Codes Present No
Code Description Occ. First Last
No Logged Diagnostic Codes
Code Description Occ. First Last
E043 (2) Low System Voltage Warning 16 5945 6105
Code Description
Page 3 of 30
3/17/2013file://C:\Documents and Settings\All Users\Application Data\Caterpillar\Electronic Techni...
Current Totals - Machine Control 320D/323D
No Active Codes
Description Value Unit
Total Operating Hours 6928 hours
Engine Maintenance Hours 6927 hours
Engine Oil Hours 5259 hours
Engine Oil Filter Hours 5259 hours
Engine Coolant Hours 6927 hours
Fuel/ Water Separator Hours 5259 hours
Fuel Filter Hours 0 hours
Secondary Fuel Filter Hours 5259 hours
Tertiary Fuel Filter Hours 5259 hours
Fuel Tank Cap Hours 0 hours
Hydraulic Pump Hours 6927 hours
Hydraulic Pilot Oil Filter Hours 6927 hours
Hydraulic Case Drain Oil Filter Hours 6927 hours
Return Hydraulic Oil Filter Hours 6927 hours
Attachment Hydraulic Oil Filter Hours 0 hours
Hydraulic Oil Hours 6927 hours
Final Drive Oil Hours 6927 hours
Swing Drive Oil Hours 6927 hours
Travel Motor Hours 582 hours
Tool #1 Hours 2068 hours
Tool #2 Hours 0 hours
Tool #3 Hours 0 hours
Tool #4 Hours 0 hours
Tool #5 Hours 0 hours
Tool #6 Hours 0 hours
Tool #7 Hours 0 hours
Tool #8 Hours 0 hours
Tool #9 Hours 0 hours
Tool #10 Hours 0 hours
Return Hydraulic Oil Filter Bypass Hours 1.2 hours
Return Hydraulic Oil Filter Bypass at Cold Temperature Hours 1.1 hours
Hours of Operation at High Hydraulic Pressure 178.3 hours
Hours of Operation at Relief Hydraulic Pressure 50.0 hours
Page 4 of 30
3/17/2013file://C:\Documents and Settings\All Users\Application Data\Caterpillar\Electronic Techni...
Configuration - Machine Control 320D/323D
Description Value Unit
Product ID GKS00234
Hydraulic Power Mode High
Fuel Economy Mode Enable Status Enabled
Economy Mode Off
Travel Alarm Installation Status Installed
Water Separator Level Switch Configuration Normally Closed (to Ground)
Fuel Filter Differential Pressure Switch Config Not Installed
Secondary Fuel Filter Differential Pressure Switch Config Not Installed
Attachment Hydraulic Oil Filter Switch Configuration Not Installed
Auto Lube Warning Indicator Enable Switch Configuration
Not Installed
Machine Overload Pressure Sensor Installation Not Installed
Machine Overload Pressure Threshold Disabled or Not Installed psi
Heavy Lift System Installation Status Not Installed
Engine Fan Type Configuration Direct Drive
Engine Cooling Fan Map Standard
Engine Fan Reversing Feature Installation Status Installed
Engine Fan Reverse Operation Time 300 sec
Machine Application Configuration NACD Log Loader
Main Pump Flow Limitation Pres Sol Installation Installed
Attachment Valve #1 Configuration F2 - Two Way
Attachment Valve #2 ConfigurationAttachment Pump Valve - Two Way
Attachment Valve #3 Configuration Not Installed
Attachment Valve #4 Configuration Not Installed
Attachment Valve #1 Control Type Configuration Electrical
Attachment Valve #2 Control Type Configuration Electrical
Attachment Valve #3 Control Type Configuration Disabled or Not Installed
Attachment Valve #4 Control Type Configuration Disabled or Not Installed
Attachment Valve #1 Combiner Configuration Not Installed
Auxiliary Circuit Flow Combining Solenoid Installation Status
Disabled or Not Installed
Hammer Return to Tank Solenoid Installation Status Disabled or Not Installed
Variable Relief Valve Type Configuration Disabled or Not Installed
Variable Relief Valve #1 Configuration Not Installed
Page 5 of 30
3/17/2013file://C:\Documents and Settings\All Users\Application Data\Caterpillar\Electronic Techni...
Variable Relief Valve #2 Configuration Not Installed
F2 Type Valve Load Sense Pres Sensor Installation Not Installed
Joystick Handle Configuration Modulation Handle
Foot Switch Installation Status Not Installed
Left Attachment Pedal Installation Status Not Installed
Right Attachment Pedal Installation Status Not Installed
Left Joystick Switch #1 Control Mode No valve controlled
Left Joystick Switch #2 Control Mode No valve controlled
Left Joystick Switch #4 Control Mode Disabled or Not Installed
Right Joystick Switch #1 Control Mode No valve controlled
Right Joystick Switch #2 Control Mode No valve controlled
Right Joystick Switch #4 Control Mode Disabled or Not Installed
Foot Switch Control Mode Disabled or Not Installed
Left Joystick Thumbwheel Control Mode Attachment Valve #2
Right Joystick Thumbwheel Control Mode Attachment Valve #1
Left Attachment Pedal Control Mode Disabled or Not Installed
Right Attachment Pedal Control Mode Disabled or Not Installed
Travel Speed Shift Low Delay 0.4 sec
Travel Speed Shift High Delay 0.4 sec
Travel Speed Shift Low Pres 2611 psi
Travel Speed Shift High Pressure 4641 psi
One Touch Engine Speed Setting 1100 rpm
AESC Setting 1300 rpm
AESC Delay Time 5.0 sec
Throttle Dial Position 1 Engine Speed 1000 rpm
Throttle Dial Position 2 Engine Speed 1100 rpm
Throttle Dial Position 3 Engine Speed 1200 rpm
Throttle Dial Position 4 Engine Speed 1300 rpm
Throttle Dial Position 5 Engine Speed 1470 rpm
Throttle Dial Position 6 Engine Speed 1590 rpm
Throttle Dial Position 7 Engine Speed 1700 rpm
Throttle Dial Position 8 Engine Speed 1800 rpm
Throttle Dial Position 9 Engine Speed 1900 rpm
Throttle Dial Position 10 Engine Speed 1980 rpm
Throttle Dial Position 1 Hydraulic System Torque Percentage
20.0 %
Throttle Dial Position 2 Hydraulic System Torque Percentage
40.0 %
Throttle Dial Position 3 Hydraulic System Torque
Page 6 of 30
3/17/2013file://C:\Documents and Settings\All Users\Application Data\Caterpillar\Electronic Techni...
Percentage 60.0 %
Throttle Dial Position 4 Hydraulic System Torque Percentage
70.0 %
Throttle Dial Position 5 Hydraulic System Torque Percentage
80.0 %
Throttle Dial Position 6 Hydraulic System Torque Percentage
86.4 %
Throttle Dial Position 7 Hydraulic System Torque Percentage
92.0 %
Throttle Dial Position 8 Hydraulic System Torque Percentage
92.0 %
Throttle Dial Position 9 Hydraulic System Torque Percentage
92.0 %
Throttle Dial Position 10 Hydraulic System Torque Percentage
100.0 %
Engine Oil Recommended Maintenance Interval 500 hours
Engine Oil Filter Recommended Maintenance Interval 500 hours
Engine Coolant Recommended Maintenance Interval 3000 hours
Fuel/ Water Separator Recommended Maint Interval 500 hours
Fuel Filter Recommended Maint Interval 0 hours
Secondary Fuel Filter Recommended Maint Interval 500 hours
Tertiary Fuel Filter Recommended Maintenance Interval 500 hours
Fuel Tank Cap Recommended Maintenance Interval 0 hours
Hydraulic Pilot Oil Filter Recommended Maintenance Interval
1000 hours
Hydraulic Case Drain Oil Filter Recommended MI 1000 hours
Return Hyd Oil Filter Recommended Maint Interval 2000 hours
Attachment Hydraulic Oil Filter Recommended Maintenance Interval
0 hours
Final Drive Oil Recommended Maintenance Interval 2000 hours
Hydraulic Oil Recommended Maintenance Interval 2000 hours
Swing Drive Oil Recommended Maintenance Interval 1000 hours
Advanced Machine Security System Installation Status Not Installed
Sunday Security System Bypass Start Time Disabled or Not Installed
Sunday Security System Bypass Stop Time Disabled or Not Installed
Monday Security System Bypass Start Time Disabled or Not Installed
Monday Security System Bypass Stop Time Disabled or Not Installed
Tuesday Security System Bypass Start Time Disabled or Not Installed
Tuesday Security System Bypass Stop Time Disabled or Not Installed
Wednesday Security System Bypass Start Time Disabled or Not Installed
Page 7 of 30
3/17/2013file://C:\Documents and Settings\All Users\Application Data\Caterpillar\Electronic Techni...
Calibration Status - Machine Control 320D/323D
Wednesday Security System Bypass Stop Time Disabled or Not Installed
Thursday Security System Bypass Start Time Disabled or Not Installed
Thursday Security System Bypass Stop Time Disabled or Not Installed
Friday Security System Bypass Start Time Disabled or Not Installed
Friday Security System Bypass Stop Time Disabled or Not Installed
Saturday Security System Bypass Start Time Disabled or Not Installed
Saturday Security System Bypass Stop Time Disabled or Not Installed
AccuGrade System Installation Status Disabled or Not Installed
Hydraulic Cab Riser Installation Status Not Installed
Hydraulic Cab Riser Raise Snubbing Angle Gain Disabled or Not Installed
Hydraulic Cab Riser Raise Snubbing Rate Gain Disabled or Not Installed
Hydraulic Cab Riser Lower Snubbing Angle Gain Disabled or Not Installed
Hydraulic Cab Riser Lower Snubbing Rate Gain Disabled or Not Installed
Calibration Status Last Successful Completion
Attachment Valve #1 Extend Success 1.6 hours
Attachment Valve #1 Retract Success 1.7 hours
Attachment Valve #2 Extend Success 1358.4 hours
Attachment Valve #2 Retract Success 1.7 hours
Attachment Valve #3 ExtendNever Calibrated
Never Successfully Calibrated
Attachment Valve #3 RetractNever Calibrated
Never Successfully Calibrated
Attachment Valve #4 ExtendNever Calibrated
Never Successfully Calibrated
Attachment Valve #4 RetractNever Calibrated
Never Successfully Calibrated
Engine Speed Calibration Success 1.4 hours
Left Joystick Thumbwheel Calibration Success 1.1 hours
Right Joystick Thumbwheel Calibration Success 1.1 hours
Left Attachment Pedal CalibrationNever Calibrated
Never Successfully Calibrated
Right Attachment Pedal CalibrationNever Calibrated
Never Successfully Calibrated
PRV - Pressure Gauge Success 1.6 hours
PRV - Flow Meter for Two Pump Flow Combined Never Never Successfully
Page 8 of 30
3/17/2013file://C:\Documents and Settings\All Users\Application Data\Caterpillar\Electronic Techni...
Tool Configuration - Machine Control 320D/323D
Calibrated Calibrated
PRV - Attachment Valve #1 Flow LimitNever Calibrated
Never Successfully Calibrated
PRV - Combined Attachment Valve Flow LimitNever Calibrated
Never Successfully Calibrated
PRV - Power Shift Pressure Calibration Success 1.4 hours
Boom Cylinder Extend Pilot Pressure Limit Solenoid Cal
Never Calibrated
Never Successfully Calibrated
Stick Cylinder Retract Pilot Pressure Limit Solenoid Cal
Never Calibrated
Never Successfully Calibrated
PRV - Variable Relief Pressure Calibration Solenoid 1
Never Calibrated
Never Successfully Calibrated
PRV - Variable Relief Pressure Calibration Solenoid 2
Never Calibrated
Never Successfully Calibrated
Description Value Unit
Tool Program Name CAT GLL52 Active
Maximum Throttle Dial 10
Minimum Throttle Dial Position 1
Underspeed Enable Enabled
Two Pump Flow Combine EnableDisabled or Not Installed
Initial Tool Program Medium Pressure Circuit Main Pump Torque Reduction
5 %
Total Tool Program Medium Pressure Circuit Main Pump Torque Reduction
50 %
One Way/ Two Way Valve ModeDisabled or Not Installed
Variable Relief Valve #1 PressureDisabled or Not Installed
psi
Variable Relief Valve #2 PressureDisabled or Not Installed
psi
F2 Type Valve Max Flow Derate PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate Start PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate End PressureDisabled or Not Installed
psi
Multiple Operation Maximum Extend Pilot Pressure for Disabled or Not
Page 9 of 30
3/17/2013file://C:\Documents and Settings\All Users\Application Data\Caterpillar\Electronic Techni...
Attachment Valve #1 Installed psi
Multiple Operation Maximum Retract Pilot Pressure for Attachment Valve #1
Disabled or Not Installed
psi
Multiple Operation Maximum Extend Pilot Pres for Combined Attachment Valve
Disabled or Not Installed
psi
Multiple Operation Maximum Retract Pilot Pres for Combined Attachment Valve
Disabled or Not Installed
psi
Hydraulic Temperature High Warning Event Threshold 258.8 Deg F
Attachment Valve #1 Flow Setting 54 gal/min
Attachment Valve #1 Multi-Oper. Additional Flow 0 gal/min
Valve #1 Nominal Pressure 2321 psi
Attachment Valve #1 Maximum Extend Pressure 580 psi
Attachment Valve #1 Maximum Retract Pressure 580 psi
Attachment Valve #1 Open Time 0.20 sec
Attachment Valve #1 Close Time 0.20 sec
Attachment Valve #1 Tool Flow Direction Normal
Attachment Valve #2 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #2 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #2 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #2 Maximum Extend Pressure 167 psi
Attachment Valve #2 Maximum Retract Pressure 167 psi
Attachment Valve #2 Open Time 0.20 sec
Attachment Valve #2 Close Time 0.20 sec
Attachment Valve #2 Tool Flow Direction Normal
Attachment Valve #3 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #3 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #3 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #3 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #3 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #3 Open TimeDisabled or Not Installed
sec
Attachment Valve #3 Close TimeDisabled or Not Installed
sec
Page 10 of 30
3/17/2013file://C:\Documents and Settings\All Users\Application Data\Caterpillar\Electronic Techni...
Tool Configuration - Machine Control 320D/323D
Attachment Valve #3 Tool Flow DirectionDisabled or Not Installed
Attachment Valve #4 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #4 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #4 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #4 Open TimeDisabled or Not Installed
sec
Attachment Valve #4 Close TimeDisabled or Not Installed
sec
Attachment Valve #4 Tool Flow DirectionDisabled or Not Installed
Description Value Unit
Tool Program Name 0
Maximum Throttle Dial 10
Minimum Throttle Dial Position 1
Underspeed Enable Enabled
Two Pump Flow Combine EnableDisabled or Not Installed
Initial Tool Program Medium Pressure Circuit Main Pump Torque Reduction
5 %
Total Tool Program Medium Pressure Circuit Main Pump Torque Reduction
50 %
One Way/ Two Way Valve ModeDisabled or Not Installed
Variable Relief Valve #1 PressureDisabled or Not Installed
psi
Variable Relief Valve #2 PressureDisabled or Not Installed
psi
F2 Type Valve Max Flow Derate PressureDisabled or Not Installed
psi
Disabled or Not
Page 11 of 30
3/17/2013file://C:\Documents and Settings\All Users\Application Data\Caterpillar\Electronic Techni...
F2 Type Valve Flow Derate Start Pressure Installed psi
F2 Type Valve Flow Derate End PressureDisabled or Not Installed
psi
Multiple Operation Maximum Extend Pilot Pressure for Attachment Valve #1
Disabled or Not Installed
psi
Multiple Operation Maximum Retract Pilot Pressure for Attachment Valve #1
Disabled or Not Installed
psi
Multiple Operation Maximum Extend Pilot Pres for Combined Attachment Valve
Disabled or Not Installed
psi
Multiple Operation Maximum Retract Pilot Pres for Combined Attachment Valve
Disabled or Not Installed
psi
Hydraulic Temperature High Warning Event Threshold 258.8 Deg F
Attachment Valve #1 Flow Setting 54 gal/min
Attachment Valve #1 Multi-Oper. Additional Flow 0 gal/min
Valve #1 Nominal Pressure 2321 psi
Attachment Valve #1 Maximum Extend Pressure 580 psi
Attachment Valve #1 Maximum Retract Pressure 580 psi
Attachment Valve #1 Open Time 0.20 sec
Attachment Valve #1 Close Time 0.20 sec
Attachment Valve #1 Tool Flow Direction Normal
Attachment Valve #2 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #2 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #2 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #2 Maximum Extend Pressure 167 psi
Attachment Valve #2 Maximum Retract Pressure 167 psi
Attachment Valve #2 Open Time 0.20 sec
Attachment Valve #2 Close Time 0.20 sec
Attachment Valve #2 Tool Flow Direction Normal
Attachment Valve #3 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #3 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #3 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #3 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #3 Maximum Retract PressureDisabled or Not Installed
psi
Page 12 of 30
3/17/2013file://C:\Documents and Settings\All Users\Application Data\Caterpillar\Electronic Techni...
Tool Configuration - Machine Control 320D/323D
Attachment Valve #3 Open TimeDisabled or Not Installed
sec
Attachment Valve #3 Close TimeDisabled or Not Installed
sec
Attachment Valve #3 Tool Flow DirectionDisabled or Not Installed
Attachment Valve #4 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #4 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #4 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #4 Open TimeDisabled or Not Installed
sec
Attachment Valve #4 Close TimeDisabled or Not Installed
sec
Attachment Valve #4 Tool Flow DirectionDisabled or Not Installed
Description Value Unit
Tool Program Name 0
Maximum Throttle Dial 10
Minimum Throttle Dial Position 1
Underspeed Enable Enabled
Two Pump Flow Combine EnableDisabled or Not Installed
Initial Tool Program Medium Pressure Circuit Main Pump Torque Reduction
5 %
Total Tool Program Medium Pressure Circuit Main Pump Torque Reduction
50 %
One Way/ Two Way Valve ModeDisabled or Not Installed
Variable Relief Valve #1 PressureDisabled or Not Installed
psi
Disabled or Not
Page 13 of 30
3/17/2013file://C:\Documents and Settings\All Users\Application Data\Caterpillar\Electronic Techni...
Variable Relief Valve #2 Pressure Installed psi
F2 Type Valve Max Flow Derate PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate Start PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate End PressureDisabled or Not Installed
psi
Multiple Operation Maximum Extend Pilot Pressure for Attachment Valve #1
Disabled or Not Installed
psi
Multiple Operation Maximum Retract Pilot Pressure for Attachment Valve #1
Disabled or Not Installed
psi
Multiple Operation Maximum Extend Pilot Pres for Combined Attachment Valve
Disabled or Not Installed
psi
Multiple Operation Maximum Retract Pilot Pres for Combined Attachment Valve
Disabled or Not Installed
psi
Hydraulic Temperature High Warning Event Threshold 258.8 Deg F
Attachment Valve #1 Flow Setting 54 gal/min
Attachment Valve #1 Multi-Oper. Additional Flow 0 gal/min
Valve #1 Nominal Pressure 2321 psi
Attachment Valve #1 Maximum Extend Pressure 580 psi
Attachment Valve #1 Maximum Retract Pressure 580 psi
Attachment Valve #1 Open Time 0.20 sec
Attachment Valve #1 Close Time 0.20 sec
Attachment Valve #1 Tool Flow Direction Normal
Attachment Valve #2 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #2 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #2 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #2 Maximum Extend Pressure 167 psi
Attachment Valve #2 Maximum Retract Pressure 167 psi
Attachment Valve #2 Open Time 0.20 sec
Attachment Valve #2 Close Time 0.20 sec
Attachment Valve #2 Tool Flow Direction Normal
Attachment Valve #3 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #3 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #3 Nominal PressureDisabled or Not Installed
psi
Page 14 of 30
3/17/2013file://C:\Documents and Settings\All Users\Application Data\Caterpillar\Electronic Techni...
Tool Configuration - Machine Control 320D/323D
Attachment Valve #3 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #3 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #3 Open TimeDisabled or Not Installed
sec
Attachment Valve #3 Close TimeDisabled or Not Installed
sec
Attachment Valve #3 Tool Flow DirectionDisabled or Not Installed
Attachment Valve #4 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #4 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #4 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #4 Open TimeDisabled or Not Installed
sec
Attachment Valve #4 Close TimeDisabled or Not Installed
sec
Attachment Valve #4 Tool Flow DirectionDisabled or Not Installed
Description Value Unit
Tool Program Name 0
Maximum Throttle Dial 10
Minimum Throttle Dial Position 1
Underspeed Enable Enabled
Two Pump Flow Combine EnableDisabled or Not Installed
Initial Tool Program Medium Pressure Circuit Main Pump Torque Reduction
5 %
Total Tool Program Medium Pressure Circuit Main Pump Torque Reduction
50 %
Disabled or Not
Page 15 of 30
3/17/2013file://C:\Documents and Settings\All Users\Application Data\Caterpillar\Electronic Techni...
One Way/ Two Way Valve Mode Installed
Variable Relief Valve #1 PressureDisabled or Not Installed
psi
Variable Relief Valve #2 PressureDisabled or Not Installed
psi
F2 Type Valve Max Flow Derate PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate Start PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate End PressureDisabled or Not Installed
psi
Multiple Operation Maximum Extend Pilot Pressure for Attachment Valve #1
Disabled or Not Installed
psi
Multiple Operation Maximum Retract Pilot Pressure for Attachment Valve #1
Disabled or Not Installed
psi
Multiple Operation Maximum Extend Pilot Pres for Combined Attachment Valve
Disabled or Not Installed
psi
Multiple Operation Maximum Retract Pilot Pres for Combined Attachment Valve
Disabled or Not Installed
psi
Hydraulic Temperature High Warning Event Threshold 258.8 Deg F
Attachment Valve #1 Flow Setting 54 gal/min
Attachment Valve #1 Multi-Oper. Additional Flow 0 gal/min
Valve #1 Nominal Pressure 2321 psi
Attachment Valve #1 Maximum Extend Pressure 580 psi
Attachment Valve #1 Maximum Retract Pressure 580 psi
Attachment Valve #1 Open Time 0.20 sec
Attachment Valve #1 Close Time 0.20 sec
Attachment Valve #1 Tool Flow Direction Normal
Attachment Valve #2 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #2 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #2 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #2 Maximum Extend Pressure 167 psi
Attachment Valve #2 Maximum Retract Pressure 167 psi
Attachment Valve #2 Open Time 0.20 sec
Attachment Valve #2 Close Time 0.20 sec
Attachment Valve #2 Tool Flow Direction Normal
Attachment Valve #3 Flow SettingDisabled or Not Installed
gal/min
Page 16 of 30
3/17/2013file://C:\Documents and Settings\All Users\Application Data\Caterpillar\Electronic Techni...
Tool Configuration - Machine Control 320D/323D
Attachment Valve #3 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #3 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #3 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #3 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #3 Open TimeDisabled or Not Installed
sec
Attachment Valve #3 Close TimeDisabled or Not Installed
sec
Attachment Valve #3 Tool Flow DirectionDisabled or Not Installed
Attachment Valve #4 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #4 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #4 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #4 Open TimeDisabled or Not Installed
sec
Attachment Valve #4 Close TimeDisabled or Not Installed
sec
Attachment Valve #4 Tool Flow DirectionDisabled or Not Installed
Description Value Unit
Tool Program Name 0
Maximum Throttle Dial 10
Minimum Throttle Dial Position 1
Underspeed Enable Enabled
Two Pump Flow Combine EnableDisabled or Not Installed
Initial Tool Program Medium Pressure Circuit Main Pump
Page 17 of 30
3/17/2013file://C:\Documents and Settings\All Users\Application Data\Caterpillar\Electronic Techni...
Torque Reduction 5 %
Total Tool Program Medium Pressure Circuit Main Pump Torque Reduction
50 %
One Way/ Two Way Valve ModeDisabled or Not Installed
Variable Relief Valve #1 PressureDisabled or Not Installed
psi
Variable Relief Valve #2 PressureDisabled or Not Installed
psi
F2 Type Valve Max Flow Derate PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate Start PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate End PressureDisabled or Not Installed
psi
Multiple Operation Maximum Extend Pilot Pressure for Attachment Valve #1
Disabled or Not Installed
psi
Multiple Operation Maximum Retract Pilot Pressure for Attachment Valve #1
Disabled or Not Installed
psi
Multiple Operation Maximum Extend Pilot Pres for Combined Attachment Valve
Disabled or Not Installed
psi
Multiple Operation Maximum Retract Pilot Pres for Combined Attachment Valve
Disabled or Not Installed
psi
Hydraulic Temperature High Warning Event Threshold 258.8 Deg F
Attachment Valve #1 Flow Setting 54 gal/min
Attachment Valve #1 Multi-Oper. Additional Flow 0 gal/min
Valve #1 Nominal Pressure 2321 psi
Attachment Valve #1 Maximum Extend Pressure 580 psi
Attachment Valve #1 Maximum Retract Pressure 580 psi
Attachment Valve #1 Open Time 0.20 sec
Attachment Valve #1 Close Time 0.20 sec
Attachment Valve #1 Tool Flow Direction Normal
Attachment Valve #2 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #2 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #2 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #2 Maximum Extend Pressure 167 psi
Attachment Valve #2 Maximum Retract Pressure 167 psi
Attachment Valve #2 Open Time 0.20 sec
Page 18 of 30
3/17/2013file://C:\Documents and Settings\All Users\Application Data\Caterpillar\Electronic Techni...
Tool Configuration - Machine Control 320D/323D
Attachment Valve #2 Close Time 0.20 sec
Attachment Valve #2 Tool Flow Direction Normal
Attachment Valve #3 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #3 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #3 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #3 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #3 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #3 Open TimeDisabled or Not Installed
sec
Attachment Valve #3 Close TimeDisabled or Not Installed
sec
Attachment Valve #3 Tool Flow DirectionDisabled or Not Installed
Attachment Valve #4 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #4 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #4 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #4 Open TimeDisabled or Not Installed
sec
Attachment Valve #4 Close TimeDisabled or Not Installed
sec
Attachment Valve #4 Tool Flow DirectionDisabled or Not Installed
Description Value Unit
Tool Program Name 0
Maximum Throttle Dial 10
Minimum Throttle Dial Position 1
Page 19 of 30
3/17/2013file://C:\Documents and Settings\All Users\Application Data\Caterpillar\Electronic Techni...
Underspeed Enable Enabled
Two Pump Flow Combine EnableDisabled or Not Installed
Initial Tool Program Medium Pressure Circuit Main Pump Torque Reduction
5 %
Total Tool Program Medium Pressure Circuit Main Pump Torque Reduction
50 %
One Way/ Two Way Valve ModeDisabled or Not Installed
Variable Relief Valve #1 PressureDisabled or Not Installed
psi
Variable Relief Valve #2 PressureDisabled or Not Installed
psi
F2 Type Valve Max Flow Derate PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate Start PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate End PressureDisabled or Not Installed
psi
Multiple Operation Maximum Extend Pilot Pressure for Attachment Valve #1
Disabled or Not Installed
psi
Multiple Operation Maximum Retract Pilot Pressure for Attachment Valve #1
Disabled or Not Installed
psi
Multiple Operation Maximum Extend Pilot Pres for Combined Attachment Valve
Disabled or Not Installed
psi
Multiple Operation Maximum Retract Pilot Pres for Combined Attachment Valve
Disabled or Not Installed
psi
Hydraulic Temperature High Warning Event Threshold 258.8 Deg F
Attachment Valve #1 Flow Setting 54 gal/min
Attachment Valve #1 Multi-Oper. Additional Flow 0 gal/min
Valve #1 Nominal Pressure 2321 psi
Attachment Valve #1 Maximum Extend Pressure 580 psi
Attachment Valve #1 Maximum Retract Pressure 580 psi
Attachment Valve #1 Open Time 0.20 sec
Attachment Valve #1 Close Time 0.20 sec
Attachment Valve #1 Tool Flow Direction Normal
Attachment Valve #2 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #2 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Disabled or Not
Page 20 of 30
3/17/2013file://C:\Documents and Settings\All Users\Application Data\Caterpillar\Electronic Techni...
Tool Configuration - Machine Control 320D/323D
Valve #2 Nominal Pressure Installed psi
Attachment Valve #2 Maximum Extend Pressure 167 psi
Attachment Valve #2 Maximum Retract Pressure 167 psi
Attachment Valve #2 Open Time 0.20 sec
Attachment Valve #2 Close Time 0.20 sec
Attachment Valve #2 Tool Flow Direction Normal
Attachment Valve #3 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #3 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #3 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #3 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #3 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #3 Open TimeDisabled or Not Installed
sec
Attachment Valve #3 Close TimeDisabled or Not Installed
sec
Attachment Valve #3 Tool Flow DirectionDisabled or Not Installed
Attachment Valve #4 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #4 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #4 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #4 Open TimeDisabled or Not Installed
sec
Attachment Valve #4 Close TimeDisabled or Not Installed
sec
Attachment Valve #4 Tool Flow DirectionDisabled or Not Installed
Page 21 of 30
3/17/2013file://C:\Documents and Settings\All Users\Application Data\Caterpillar\Electronic Techni...
Description Value Unit
Tool Program Name 0
Maximum Throttle Dial 10
Minimum Throttle Dial Position 1
Underspeed Enable Enabled
Two Pump Flow Combine EnableDisabled or Not Installed
Initial Tool Program Medium Pressure Circuit Main Pump Torque Reduction
5 %
Total Tool Program Medium Pressure Circuit Main Pump Torque Reduction
50 %
One Way/ Two Way Valve ModeDisabled or Not Installed
Variable Relief Valve #1 PressureDisabled or Not Installed
psi
Variable Relief Valve #2 PressureDisabled or Not Installed
psi
F2 Type Valve Max Flow Derate PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate Start PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate End PressureDisabled or Not Installed
psi
Multiple Operation Maximum Extend Pilot Pressure for Attachment Valve #1
Disabled or Not Installed
psi
Multiple Operation Maximum Retract Pilot Pressure for Attachment Valve #1
Disabled or Not Installed
psi
Multiple Operation Maximum Extend Pilot Pres for Combined Attachment Valve
Disabled or Not Installed
psi
Multiple Operation Maximum Retract Pilot Pres for Combined Attachment Valve
Disabled or Not Installed
psi
Hydraulic Temperature High Warning Event Threshold 258.8 Deg F
Attachment Valve #1 Flow Setting 54 gal/min
Attachment Valve #1 Multi-Oper. Additional Flow 0 gal/min
Valve #1 Nominal Pressure 2321 psi
Attachment Valve #1 Maximum Extend Pressure 580 psi
Attachment Valve #1 Maximum Retract Pressure 580 psi
Attachment Valve #1 Open Time 0.20 sec
Attachment Valve #1 Close Time 0.20 sec
Attachment Valve #1 Tool Flow Direction Normal
Disabled or Not
Page 22 of 30
3/17/2013file://C:\Documents and Settings\All Users\Application Data\Caterpillar\Electronic Techni...
Attachment Valve #2 Flow Setting Installed gal/min
Attachment Valve #2 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #2 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #2 Maximum Extend Pressure 167 psi
Attachment Valve #2 Maximum Retract Pressure 167 psi
Attachment Valve #2 Open Time 0.20 sec
Attachment Valve #2 Close Time 0.20 sec
Attachment Valve #2 Tool Flow Direction Normal
Attachment Valve #3 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #3 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #3 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #3 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #3 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #3 Open TimeDisabled or Not Installed
sec
Attachment Valve #3 Close TimeDisabled or Not Installed
sec
Attachment Valve #3 Tool Flow DirectionDisabled or Not Installed
Attachment Valve #4 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #4 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #4 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #4 Open TimeDisabled or Not Installed
sec
Attachment Valve #4 Close TimeDisabled or Not Installed
sec
Attachment Valve #4 Tool Flow DirectionDisabled or Not
Page 23 of 30
3/17/2013file://C:\Documents and Settings\All Users\Application Data\Caterpillar\Electronic Techni...
Tool Configuration - Machine Control 320D/323D
Installed
Description Value Unit
Tool Program Name 0
Maximum Throttle Dial 10
Minimum Throttle Dial Position 1
Underspeed Enable Enabled
Two Pump Flow Combine EnableDisabled or Not Installed
Initial Tool Program Medium Pressure Circuit Main Pump Torque Reduction
5 %
Total Tool Program Medium Pressure Circuit Main Pump Torque Reduction
50 %
One Way/ Two Way Valve ModeDisabled or Not Installed
Variable Relief Valve #1 PressureDisabled or Not Installed
psi
Variable Relief Valve #2 PressureDisabled or Not Installed
psi
F2 Type Valve Max Flow Derate PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate Start PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate End PressureDisabled or Not Installed
psi
Multiple Operation Maximum Extend Pilot Pressure for Attachment Valve #1
Disabled or Not Installed
psi
Multiple Operation Maximum Retract Pilot Pressure for Attachment Valve #1
Disabled or Not Installed
psi
Multiple Operation Maximum Extend Pilot Pres for Combined Attachment Valve
Disabled or Not Installed
psi
Multiple Operation Maximum Retract Pilot Pres for Combined Attachment Valve
Disabled or Not Installed
psi
Hydraulic Temperature High Warning Event Threshold 258.8 Deg F
Attachment Valve #1 Flow Setting 54 gal/min
Attachment Valve #1 Multi-Oper. Additional Flow 0 gal/min
Valve #1 Nominal Pressure 2321 psi
Attachment Valve #1 Maximum Extend Pressure 580 psi
Page 24 of 30
3/17/2013file://C:\Documents and Settings\All Users\Application Data\Caterpillar\Electronic Techni...
Attachment Valve #1 Maximum Retract Pressure 580 psi
Attachment Valve #1 Open Time 0.20 sec
Attachment Valve #1 Close Time 0.20 sec
Attachment Valve #1 Tool Flow Direction Normal
Attachment Valve #2 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #2 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #2 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #2 Maximum Extend Pressure 167 psi
Attachment Valve #2 Maximum Retract Pressure 167 psi
Attachment Valve #2 Open Time 0.20 sec
Attachment Valve #2 Close Time 0.20 sec
Attachment Valve #2 Tool Flow Direction Normal
Attachment Valve #3 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #3 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #3 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #3 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #3 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #3 Open TimeDisabled or Not Installed
sec
Attachment Valve #3 Close TimeDisabled or Not Installed
sec
Attachment Valve #3 Tool Flow DirectionDisabled or Not Installed
Attachment Valve #4 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #4 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #4 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Retract PressureDisabled or Not Installed
psi
Page 25 of 30
3/17/2013file://C:\Documents and Settings\All Users\Application Data\Caterpillar\Electronic Techni...
Tool Configuration - Machine Control 320D/323D
Attachment Valve #4 Open TimeDisabled or Not Installed
sec
Attachment Valve #4 Close TimeDisabled or Not Installed
sec
Attachment Valve #4 Tool Flow DirectionDisabled or Not Installed
Description Value Unit
Tool Program Name 0
Maximum Throttle Dial 10
Minimum Throttle Dial Position 1
Underspeed Enable Enabled
Two Pump Flow Combine EnableDisabled or Not Installed
Initial Tool Program Medium Pressure Circuit Main Pump Torque Reduction
5 %
Total Tool Program Medium Pressure Circuit Main Pump Torque Reduction
50 %
One Way/ Two Way Valve ModeDisabled or Not Installed
Variable Relief Valve #1 PressureDisabled or Not Installed
psi
Variable Relief Valve #2 PressureDisabled or Not Installed
psi
F2 Type Valve Max Flow Derate PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate Start PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate End PressureDisabled or Not Installed
psi
Multiple Operation Maximum Extend Pilot Pressure for Attachment Valve #1
Disabled or Not Installed
psi
Multiple Operation Maximum Retract Pilot Pressure for Attachment Valve #1
Disabled or Not Installed
psi
Multiple Operation Maximum Extend Pilot Pres for Combined Attachment Valve
Disabled or Not Installed
psi
Multiple Operation Maximum Retract Pilot Pres for Combined Attachment Valve
Disabled or Not Installed
psi
Hydraulic Temperature High Warning Event Threshold 258.8 Deg F
Page 26 of 30
3/17/2013file://C:\Documents and Settings\All Users\Application Data\Caterpillar\Electronic Techni...
Attachment Valve #1 Flow Setting 54 gal/min
Attachment Valve #1 Multi-Oper. Additional Flow 0 gal/min
Valve #1 Nominal Pressure 2321 psi
Attachment Valve #1 Maximum Extend Pressure 580 psi
Attachment Valve #1 Maximum Retract Pressure 580 psi
Attachment Valve #1 Open Time 0.20 sec
Attachment Valve #1 Close Time 0.20 sec
Attachment Valve #1 Tool Flow Direction Normal
Attachment Valve #2 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #2 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #2 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #2 Maximum Extend Pressure 167 psi
Attachment Valve #2 Maximum Retract Pressure 167 psi
Attachment Valve #2 Open Time 0.20 sec
Attachment Valve #2 Close Time 0.20 sec
Attachment Valve #2 Tool Flow Direction Normal
Attachment Valve #3 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #3 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #3 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #3 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #3 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #3 Open TimeDisabled or Not Installed
sec
Attachment Valve #3 Close TimeDisabled or Not Installed
sec
Attachment Valve #3 Tool Flow DirectionDisabled or Not Installed
Attachment Valve #4 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #4 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #4 Nominal PressureDisabled or Not Installed
psi
Page 27 of 30
3/17/2013file://C:\Documents and Settings\All Users\Application Data\Caterpillar\Electronic Techni...
Tool Configuration - Machine Control 320D/323D
Attachment Valve #4 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #4 Open TimeDisabled or Not Installed
sec
Attachment Valve #4 Close TimeDisabled or Not Installed
sec
Attachment Valve #4 Tool Flow DirectionDisabled or Not Installed
Description Value Unit
Tool Program Name 0
Maximum Throttle Dial 10
Minimum Throttle Dial Position 1
Underspeed Enable Enabled
Two Pump Flow Combine EnableDisabled or Not Installed
Initial Tool Program Medium Pressure Circuit Main Pump Torque Reduction
5 %
Total Tool Program Medium Pressure Circuit Main Pump Torque Reduction
50 %
One Way/ Two Way Valve ModeDisabled or Not Installed
Variable Relief Valve #1 PressureDisabled or Not Installed
psi
Variable Relief Valve #2 PressureDisabled or Not Installed
psi
F2 Type Valve Max Flow Derate PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate Start PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate End PressureDisabled or Not Installed
psi
Multiple Operation Maximum Extend Pilot Pressure for Attachment Valve #1
Disabled or Not Installed
psi
Multiple Operation Maximum Retract Pilot Pressure for Attachment Valve #1
Disabled or Not Installed
psi
Multiple Operation Maximum Extend Pilot Pres for Combined Disabled or Not
Page 28 of 30
3/17/2013file://C:\Documents and Settings\All Users\Application Data\Caterpillar\Electronic Techni...
Attachment Valve Installed psi
Multiple Operation Maximum Retract Pilot Pres for Combined Attachment Valve
Disabled or Not Installed
psi
Hydraulic Temperature High Warning Event Threshold 258.8 Deg F
Attachment Valve #1 Flow Setting 54 gal/min
Attachment Valve #1 Multi-Oper. Additional Flow 0 gal/min
Valve #1 Nominal Pressure 2321 psi
Attachment Valve #1 Maximum Extend Pressure 580 psi
Attachment Valve #1 Maximum Retract Pressure 580 psi
Attachment Valve #1 Open Time 0.20 sec
Attachment Valve #1 Close Time 0.20 sec
Attachment Valve #1 Tool Flow Direction Normal
Attachment Valve #2 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #2 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #2 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #2 Maximum Extend Pressure 167 psi
Attachment Valve #2 Maximum Retract Pressure 167 psi
Attachment Valve #2 Open Time 0.20 sec
Attachment Valve #2 Close Time 0.20 sec
Attachment Valve #2 Tool Flow Direction Normal
Attachment Valve #3 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #3 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #3 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #3 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #3 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #3 Open TimeDisabled or Not Installed
sec
Attachment Valve #3 Close TimeDisabled or Not Installed
sec
Attachment Valve #3 Tool Flow DirectionDisabled or Not Installed
Attachment Valve #4 Flow SettingDisabled or Not Installed
gal/min
Page 29 of 30
3/17/2013file://C:\Documents and Settings\All Users\Application Data\Caterpillar\Electronic Techni...
Monitor
Attachment Valve #4 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #4 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #4 Open TimeDisabled or Not Installed
sec
Attachment Valve #4 Close TimeDisabled or Not Installed
sec
Attachment Valve #4 Tool Flow DirectionDisabled or Not Installed
Parameter Value
ECM Serial Number 08YJ1923AJ
Personality Module Part Number 3495410-00
Page 30 of 30
3/17/2013file://C:\Documents and Settings\All Users\Application Data\Caterpillar\Electronic Techni...