Upload
trandien
View
216
Download
1
Embed Size (px)
Citation preview
CATALOG JULY 2008
Multizone Pager/ MixerMultiZone Amplifier
4 Ohm AmplifierPlus Series with RS 232
70 Volt Dual ZonePlus Series 70 Volt with RS 232
Plenum Equipment Box 2 RU Rack Mount Plenum Box Ceiling Tile Kit
1RU Rack Mount Shelf Pole Mount Platform Limpet Security Device
1RU Speaker Unit
Available August 08
RS 485 MULTIZONE SERIES
MINIATURE AMPLIFIERS
MOUNTING OPTIONS
STANDARD & PLUS SERIES
45 WATT MONO / STEREO AMPLIFIER
45 Watts RMS Mono / Stereo Output into 4 Ohms gives you plenty of output for one or two 4 or 8 Ohm Speakers. In Multiple SpeakerInstallations, 8 Ohm Speakers work best in this type of Installation. Information on Speaker Wiring is published on our Web Sitewww.nigelbdesign.com under “Tech Manuals,” which explains why 8 Ohm Speakers are the preferred choice in these situations.
CHOSE YOUR INPUT
Please see over for specifications and helpful Ideas
Part # NB-2075Requires NB-PS75 AC Power Supply
Internal circuity enables the user to configure the Amplifier to be used in either Balanced or Unbalanced Modes depending on the connections used.Shown below are the different Line In Connections that allow the Amplifier to accept either Balanced or Unbalanced Stereo, or Balanced BridgedMono Inputs, depending on the user's requirements.
BALANCED STEREO UNBALANCED STEREO UNBALANCED BRIDGED MONO BALANCED BRIDGED MONO
--
- -+ +
+ + + ++ +
. . ..SPEAKER OUTS
BRIDGED MONO8 Ohms
SHEI
LD
SHEI
LD
SHEI
LD
SHEI
LD
CC C
MONO / STEREO BALANCED ORUNBALANCED INPUT/OUTPUT
ENERGY SAVING FEATUREThe Amplifier features our ADC (Auto Detection Circuit) that reduces the power Consumption by a significant amount when the Amplifier is not in use.ADC works within 2 milliseconds of receiving an audio signal and the Amplifier will stay on until no Audio Signal is Present. This way, no On/Off Switch
is needed. As soon as Audio is again present the Amplifier will resume operation. After 30 second the Amplifier will go off until activated again.
All our Amplifiers use (An Automatic Detection Circuit) saving Energy & Reduced Operating Costs
Our Amplifiers reduce Engery Use from4.5 Amps to .025 amps in "Stand By" Mode
ACD
ADC
(An Energy Cost Saving of over 90%)
LeftRight
Nigel B Design, Inc. California, USA. Tel: (818) 487-9323 Fax: (818) 766-9805Web Site: www.nigelbdesign.com. E-Mail: [email protected]
PLENUM RATED EQUIPMENT BOXES
Inside the Plenum Equipment Boxshowing the Amplifier, Power Supply
and Built-In AC Receptacle
Both Units fit into any Plenum or Ceiling Space
POLE MOUNT PLATFORMFits on any 1 /12" Projector PoleWithout Modification to the Pole
Need more OutletsFit an Extension Tap
Hanging or Flat Surface Version
ASK US ABOUT OUR LIMPET™ ANTI THEFT ALARM SYSTEMThis device provides 24 hour 7 days Security to any Projector, Plasma Screen or in fact any Equipment you want to protect
from theft.
All Wiring and Cabling runs inside the Pole without ModificationEliminating the need to Tie Wrap anything outside the Pole
3 OUTLET POWER PANEL
Pole Mount Version
AMPLIFIER SPECIFICATION ADC - STAND BY MODE45 watts Stereo into 4 Ohms(22.5 watts per Channel)75 watts Peak Music PowerFrequency Response: 15 Hz - 22 kHzSignal to Noise Ratio: -65 dBTotal Harmonic Distortion: .003 dBDynamic Range: 115 dBOverload Protection: Built InAll Screw Connectors
REQUIRED OPTIONPower Supply UL / CSA Listed110V - 12V 4.5 Amps AC
Power is reduced from4.5 Amps to to less than 250 milliamps in Stand By Mode
1 NB-2075 M o d e l 75 M o no / S te re o 45 watts RM S A m p l i f i e r $ 299.95
2 NB-PS75 P o we r S up p l y 117v - 12v A C 4. 5 A m p s fo r ab o v e $ 49.95
PLUSSERIES 45 WATT MONO OR STEREO AMPLIFIER
ACCEPTS BALANCED ORUNBALANCED INPUTS FOR
STEREO OR MONOOPERATION
A wonder in ENERGY EFFICIENCY these COOL RUNNING AUTOMATIC Amplifiers turn themselves on in less than 2 milliseconds of detectingan Audio Signal. When no Audio signal is detected they will automatically turn themselves off after about 30 seconds, unless the Audio is restoredbefore the cutoff period, at which time theAmplifier will repeat the Active Mode until finally no signal is detected.
ADCADCADCADCADC
AUTOMATIC INTERNAL CONFIGURATION OF THE LINE INPUT
Internal circuity enables the user to configure the Amplifier to be used in either Balanced or Unbalanced Modes depending on the connections used.Shown above are the different Line In Connections that allow the Amplifier to accept either Balanced or Unbalanced Stereo, Balanced Dual Mono orBalanced Bridged Mono Inputs, depending on the user's requirements.
45 WATTS RMS INTO 4 OHMS OR 8 OHMS SINGLE OR MULTIPLESPEAKER INSTALLIONS FOR SUPERIOR SOUND OUTPUT
IN EITHER MONO OR STEREO MODES
BALANCED STEREO UNBALANCED STEREO UNBALANCED BRIDGED MONOBALANCED DUAL MONO
SHIE
LD
SHIE
LD
SHIE
LD
+ + + + _ _
ADC
BALANCED BRIDGED MONO
+_
SHIE
LD
cccSH
IELD
+ +
c
_
cc
TWO WAY RS 232 PORTFOR CONTROL FROM ANY AMX®,CRESTRON® AURORA WACI® orSTAR DRAW® CONROL CONTROLOR OTHER SOFTWARE DEVICES
Or Download the Protocol from ourWeb Site for Custom Applications
RS 232 PORT FOR TOTAL CONTROL
PHOENIX® TYPE TERMINALS FOR FAST CONNECTIONS
The Amplifier provides Two Way Communication supporting almost any Control Device including AMX®, Crestron® or Aurora Waci® Control Devices.The Amplifier can receive and confirm the following Commands:Amplier Volume - Left Channel, Right Channel (For Balance) Up and Down, Mute and Speaker Connection Confirmation. As On and Off are an AutomaticFunctions of the Amplifier there is no need to provide these from the RS 232 Port.
In addition, Software Controllers such as Stardraw etc that use Global Cache allow these functions to be made from any Computer.
SUPER FAST - ADC- AUTOMATIC DETECTION CIRCUIT- ELIMINATES SOUND CLIPPING & SAVE ENERGY
Please turn over for Mounting Options and SpecsWe Are AMX®, Crestron®, Aurora® and Stardraw Control Certified Partners
Part # NB-2052PL Requires NB-PS75 AC Power Supply
All our Energy Efficient Amplifiers use (An Automatic Detection Circuit) for Automatic
for saving Energy
Efficiency
ON/Off reducing Energy & Operating Costs
Nigel B Design, Inc. California, USA. Tel: (818) 487-9323 Fax: (818) 766-9805Web Site: www.nigelbdesign.com. E-Mail: [email protected]
AMPLIFIER SPECIFICATIONS45 watts RMS Stereo into 4 Ohms(22.5 watts per Channel)75 watts Peak Music PowerFrequency Response: 15 Hz - 22 kHzSignal to Noise Ratio: -65 dBTotal Harmonic Distortion: .003 dBDynamic Range: 115 dBOverload Protection: Built InAll Screw Connectors
NEED TO HIDE THE EQUIPMENT IN THE PLENUM
The Pole Mount Platform attaches to a Projector's1.5"dia Pole
Our Plenum Rated Equipment Box contains a 1 gang Receptacle forpowering both the Amplifier and any other equipment concealed
inside
REQUIRED OPTION
19" 1U RackFrame Shelf
Power Supply UL/CSA Listed110V - 12V 4.5 Amps AC
AUTO POWER SAVING MODEPower is reduced to 250 milliamps inStand By Mode
Hidden from view our new Plenum Rated Equipment Box allows the Amplifier, Power Supply, ACReceptacle and all the Cables to fit inside. All Cable runs are routed internally, so that the entire unitmeets UL 2034 and all Electrical Codes for Plenum Rating. Because the entire assemblyis hidden, the chance of theft is eliminated.
The RS 232 Port is a Two Way Device that receives its instructions from a variety ofControllers such as AMX®, Crestron®, Aurora Waci®, and Software such as Stardraw,in conjunction with Global Cache. Once commands are received by the Amplifier,confirmation is sent back to the Control Device.
CUSTOM APPLICATIONS (EXTRA COST)
Up to four 1/4 Rack Size Nigel BDesign Amplifiers can be fitted
taking up only 1 Rackspace
USES STANDARD SERIAL CABLE (NOT SUPPLIED)
The Protocol can be downloaded from our Web Site free of charge or you can contactour Program Engineer for specific Control Functions that you may want to be pro-grammed.
THE MARK 2 LIMPET24/7 Protection
for all your Equipment
POLE MOUNT PLATFORM
Power Cable Can be routedeither Down the inside of the PoleOr through the Optional Conduit
Part # Description List Price
NB-2052PL Plus Amplifier with RS 232 Interface $399.95
NB-PS75 Power Supply 120 v -12v AC 4.5 amps $ 49.95
NB-PEBPM Plenum Equipment Box (Pole Mount Version) $ 299.95
NB-PLWB Plenum Equipment Box (Hanging Version) $ 299.95
NB-PLHK Hanging Kit for Hanging Version $ 79.95
NB-PMP Pole Mount Platform $ 179.95
NB-2LSAS Mk 2 Limpet Electronic Alarm System $169.95
NB-1SHE 1U Rack Shelf Frame $119.95
No Modification to the Projectr's Pole is required
PLUSSERIES70 / 25 VOLT MONO/STEREO AMPLIFIER
ACCEPTS BALANCED ORUNBALANCED INPUTS FOR
STEREO OR MONOOPERATION
These ENERGY EFFICIENCY, COOL RUNNING AUTOMATIC Amplifiers turn themselves on in less than 2 milliseconds of detecting an AudioSignal. When no Audio signal is detected they will automatically turn off after about 30 Seconds, unless the Audio is restored before the cutoffperiod, at which time the unit will repeat the Active Mode until finally no signal is detected.
REDUCES THE CHANCES OF THEFT
Advanced circuitry Amplifier produces 45 Watts RMS Output into 4 Ohms, more than enough to drive Multiple 70 volt Speakers with a Clarity of Soundnot usually found in such a small Amplifier, with this amount of power the Amplifier does not have to strain itself or be "cranked up" to its extreme level,so distortion is eliminated.
ADCADCADCADCADC
SAVING ENERGY & OPERATING COSTS
As it takes up very little room, Installers are finding many different uses for this compact Amplifier. It's small size allows it to be concealed or usedin many small spaces. The entire installation of Projector, Amplifier and Power Supply can be installed at Ceiling Height or hidden inusing our Plenum Equipment Box shown on the next page.
AUTOMATIC INTERNAL CONFIGURATION OF THE LINE INPUTInternal circuity enables the user to configure the Amplifier externally for either Balanced or Unbalanced Modes depending on the connections used.Shown above are the different Line In Connections that allow the Amplifier to accept either Balanced or Unbalanced Stereo, Balanced Dual Mono orBalanced Bridged Mono Inputs, depending on the user's requirements.
45 WATTS SUPERIOR SOUND OUTPUT IN EITHER MONO OR STEREO
BALANCED STEREO UNBALANCED STEREO UNBALANCED BRIDGED MONOBALANCED DUAL MONO
SHIE
LD
SHIE
LD
SHIE
LD
+ + + + _ _
ADC
ADVANCED AMPLIFIER DESIGN WITH INCREDIBLE POWER
Please turn over for Mounting Options, Specs & List Prices
TURNS ITSELF ON AND OFF AUTOMATICALLY
BALANCED BRIDGED MONO
+_
SHIE
LD
cccSH
IELD
+ +
c
_
c
By mounting the amplifier above the Ceiling Projector or hiding it along with the other equipment in our new Plenum Equipment Box eliminates theft.
COMPACT DESIGN GIVES THE INSTALLER MANY MOUNTING OPTIONS
c
RS 232 PORTFOR CONTROL FROM ANY COMPUTER
SCREEN,AMX®, CRESTRON ® AURORAWACI® OR OTHER DEVICES*
RS 232 PORT FOR TOTAL CONTROL
PHOENIX® TYPE TERMINALS FOR FAST CONNECTIONS
The Amplifier supports almost any Control Device including AMX®, Crestron®, Aurora Waci® & Stardraw Devices. Users also have complete control fromany Computer Screen or Web Server using the Crestron QM- RMC or AMX NI Series Units. The Amplifier can also be controlled using Software Control.
(See Below)
Light Weight, Small Size and almostthree times the power of our
nearest competitor
SUPER FAST ADC - AUTOMATIC DETECTION CIRCUIT- ELIMINATES CLIPPING THE SOUND
IMPROVED SOUND QUALITYUnlike our Competitors our Transformerless 70 / 25 Volt Amplifiers use Custom made Autoformers that are Perfectly Matchedand Optimized for superior Sound Quality.
Balanced or Unbalanced and can also be Bridged
AUTOMATIC DETECTION CIRCUIT
Nigel B Design, Inc. California, USA. Tel: (818) 487-9323 Fax: (818) 766-9805Web Site: www.nigelbdesign.com. E-Mail: [email protected]
AMPLIFIER SPECIFICATIONS45 watts RMS Stereo into 4 Ohms(22.5 watts per Channel)45w Mono When Bridged75 watts Peak Music PowerFrequency Response: 15 Hz - 22 kHzSignal to Noise Ratio: -65 dBTotal Harmonic Distortion: .003 dBDynamic Range: 115 dBOverload Protection: Built InAll Screw Connectors
NEED TO HIDE THE EQUIPMENT IN THE PLENUM
The Pole Mount Platform attaches to any1.5" Projector Pole without any modification to the
Pole required, allowing all cables to be hidden
Our Plenum Rated Equipment Box contains a 1 gang Receptacle for powering both the Amplifier and any other equipment concealed inside
REQUIRED OPTION
19" 1U RackFrame Shelf
Power Supply UL/CSA Listed110V - 12V 4.5 Amps AC
AUTO POWER SAVING MODE
Power is reduced to 250 milliampsin Stand By Mode
Hidden from view, our new Plenum Rated Equipment Box allows the Amplifier, Power Supply, AC Receptacle and all the Cables to fitinside. All Cable runs are routed internally, so that the entire unit meets UL 2034 and all Electrical Codes for Plenum Rating.Because the entire assembly is hidden theft is eliminated.
NEED THE PROJECTOR CLOSE TO THE CEILING WITH THE AMPLIFIER & EQUIPMENT HIDDENUsing the Plenum Equipment Box has the benefit of being able to mount the Projector tight against the Ceiling Tiles.
RS 232 PORT SPECIFICATIONSThe RS 232 provides Two Way Communication bteween a variety of Contollers such asCrestron's ®, AMX's®, Aurora Waci® or Software such as StarDrawer Control®.For Customapplications the Protocol can be Downloaded Free of charge from our Web Site.
Up to four Ampliers can be fittedtaking up only 1 Rackspace
The LimpetFor 24/7 Set & Forget Protection
of all Your Equipment
DIMENSIONS:4.3" w, 1.75" h, 6.75" d8" Deep inc Fan
POLE MOUNT PLATFORMPerfect for all Nigel B Amplifiers,
Crestron QM-RMC AMX NI 700/900or Aurora Waci
& silmilar size Controllers
PNB-70AMP 70/25 vo lt 45 watt RMS Ste reo Amp lifie r. List Price $ 399.95
NB-PS75 Power Supply. List Price $ 49.95
NB-PMP Pole Mount Platfo rm List Price $ 179.95
NB-PEBPM Plenum Equipment Box (Po le Mount Version) List Price $ 299.95
NB-PLWB Plenum Equipment Box (Hang ing Version) List Price $ 299.95
NB-PLHK Hanging Kit for Hanging Version List Price $ 79.95
NB-1SHE 1U RackFrame She lf List Price $ 119.95
NB-1BP 1/4 Rack Blankng Pane l List Price $ 19.95
NB-2LSAS M2 Limpet Alarm system with Siren & Contact Closure List Price $ 169.95
SPECIFICATIONS
Nigel B Design, Inc. CA USA. Tel: (818) 487-9323 Fax: (818) 766-9805Web Site: www.nigelbdesign.com. E-Mail: [email protected]
Rear of Unit Connections
REQUIRED OPTIONPower Supply UL / CSA Listed110v - 12v AC 4.5 Amps
The Pole Mount Platform
MULTIPLE MOUNTING OPTIONSThe Installer is not limited to how and where the Amplifier is placed. Using the Plenum Rated Box allows everything to be hidden in the Plenum orCeiling Space. For Below Ceiling Installations the Pole Mount Platform with the Amplifier installed takes just over 2.5", allowing the Projector to sit veryclose to the Ceiling Tiles. Or use the 19" Rack Shelf that holds four Modules for installation into any 19" Equipment Rack.
Nigel B's 19" Rack Fame Shelf
Plenum Equipment Box
DUAL ZONE
Smaller Than two VHS Tapes4.3" w x 6.75" d, 1.75" h
Uses 1U Rackspace and holds four Modules
SMALL SIZE - LIGHT WEIGHT
ZONE 170/25 V OUT
ZONE 270/25 V OUT
UNBALLANCEDZONE 1 IN ZONE 2 IN
MONO STEREOSELECTOR
NEW ADVANCED CIRCUIT DESIGN FOR SUPERIOR SOUND QUALITY
Dual or Single Zone Selectable InputsMono/Stereo SwitchDual or Single Zone OutputsPower Inlet
Pole Mount Platform mountedon the Projector's Pole
Dual Zone capability allow the Amplifier to be set up with Two totally different Inputs going to two totally different Outputs. Each Zone puts out 22.5Watts Mono, In Stereo Mode 45 watts to one Zone or 22.5 watts to each Zone. Our Advanced design also allowed us to incorporate an Improvedoutput stage using Tuned Autoformers rather than "Off the Shelf" Transformers for superior Sound Quality.
70 VOLT, 25 VOLT AMPLIFIER45 WATTS RMS, SELECTABLE BETWEEN MONO & STEREO
Chose Either Single or Dual Zone Modes(see Instruction Sheet)
The Limpet Alarm System for24/7 Set & Protect all your Equipment
AMPLIFIER SECTION45 watts RMS Selectable Stereo/MonoTwo Zone Input45 watts Stereo to One Zone22.5 watts to Two Zones Mono15 Hz-22 kHz Frequency Response115 dB Dynamic Range95 dB Signal to Noise Ratio.003 Total Harmonic DistortionADC CIRCUITAutomatcic On 2 milli secondsAutomatic Off 30 secondsTRANSFORMERLESS OUTPUT SECTION2 70/25v Custom Autoformers (Built In)For Superior Performance
DIMENSIONS:4.3"w, 1.75"h, 6.75"dOverall Depth 8" inc FanWeight: 32 ozs
ADC
ENERGY SAVING AUTOMATIC DETECTION CIRCUITThis Energy Efficient Amplifier turns itself ON within 2 millseconds of hearing an Audio Signal. This eliminates any Clipping. If no Audio Signal isdetected the Ampliier will automatically go into a "Sleep" mode until a Audio Signal is again appllied.
AUTOMATIC DETECTION CIRCUITTURNS THE AMPLIFIER ON AND OFF
FAN TURNS OFFAUTOMATCALLY WHENAUDIO IS NOT PRESENT
Part # NB-70AMP 70/25 volt 45 watt RMS Stereo Amplifier. List Price $ 399.95
Part # NB-PS75 Power Supply. List Price $ 49.95
Part # NB-PMP Pole Mount Platform List Price $ 179.95
Part # NB-PEBPM Plenum Equipment Box (Pole Mount Version) List Price $ 299.95
Part # NB-PLWB Plenum Equipment Box (Hanging Version) List Price $ 299.95
Part # NB-PLHK Hanging Kit for Hanging Version List Price $ 79.95
Part # NB-1SHE 1U RackFrame Shelf List Price $ 119.95
Part # NB-1BP 1/4 Rack Blankng Panel List Price $ 19.95
OUR ENERGY EFFICIENT AMPLIFIERS REDUCE ENERGY & OPERATING COSTS
PAGING / MIXERMULTIZONESERIES
MULTIZONESERIES FOR USE WITH THE MULTIZONE AMPLIFIER
PAGING MODEGlobal Paging for Emergency Broadcasting to all ZonesIndividual Zone PagingSelective Paging
MIXING MODE
ALL WIRES ARE DAISY CHAINEDNO HOME WIRING RUNS ARE USED
RS 485 ADDRESS SELECTOR
2 Channel Audio Inputs1 Microphone Imput
Some of the many Controller Devices using RS 485
The Paging/Mixer is designed to work with our RS 485 Multizone Amplifier and both are Controlled using any Control Device.
Each Conrtoller Port can support up to 31 Multizone Devices. If the Controller has Multiple Ports the number of Multizone Devices increase by 31 peradditional Port. For Example: 5 Ports x 31= 155
WHY RS 485?RS 485 Overcomes the length limitation of RS 232. Since most Controllers support RS485 except for, the Crestron QM-RMC thislimitation is overcome by using an external RS 232-RS485 Converter Plug. A typical Unit such as the Moxa is one that is readilyavailable.
PAGING MODESEMERGENCY PAGING WITH OVER-RIDEAllows the User to Overide all Zones allowing Paging to everyone over the Entire System.
INDIVIDUAL OR SELECTIVE PAGING.The User also has the ability to Select which Zones should be paged.
MIXING MODE Controllera are programmed to allow the User to toggle between Paging and Mixer Modes. The Mixer Mode allows the Microphone Input to be mixedwith various Audio Sources connected the the Unit.
USING AN AMPLIER ONLYIn certain Aplications or Zones, Paging may not be a requirement, therefore the Paging Unit can be eliminated, so that Amplifiers can be used on theirown.
EASY LOW INSTALLATION COSTSBy eliminating the necessity to Home Run the Wiring from each zone, differentiates this product from the rest, resulting in substantialy lowerInstallation costs.
Part # Description List Price
NB-485PM Multizone Paging Mixer with RS 485 Control $449.95
NB-12DCP DC Power Supply for Paging Mixer $ 39.95
Nigel B Design, Inc, Studio City, CA.USA Tel: (818) 487-9323 Fax# (818) 766-9805e-mail: [email protected] Web: www.nigelbdesign.com
MULTIZONESERIES
ADCADCADCADCADC
RS 485 TWO WAY COMMUNICATION CONTROL
DIP SWITCHFOR SETTING INDIVIDUAL
ADDRESSES
RS 485CONNECTION
ALLOWS UNITS TO BEDAISY CHAINED TOINDIVIDUAL ZONES
Amplifiers & Paging/Mixer Units are Two Way Controlled by
In Multiple Zone Applications each unit is "Daisy Chained" providing Two Way Communication for individual, Selective or Global Control using AMX®,Crestron® Aurora Waci ® l Devices or using the supplied Protocol, Installer/Software developers can incorporate these units into any Custom Application.
ACCEPTS BALANCED ORUNBALANCED INPUTS FOR
STEREO OR MONOOPERATION
Each Controller Port supports up to 31 Zones. Depending on the Controller used each addional Port supports an additional 31Multizone Devices. For Example 5 Controller Ports x 31= 155 Multizone Devices
Because of their Small Size they can be concealed in very small spaces,Because all Wiring is Daisy Chained, eliminates the Need for Home running the wires or
Requiring Bulky Rack Installations
A Paging and Audio Amplifier Sytem that can be managed from a Central Location or at each Zone , making it a cost effiectivesolution for Restaurants Hotels, Stores, Offices, Warehouses, or in fact anywhere where Zone Placement and Control is required.
The MultiZone System consists of two low cost units, a Paging Mixer and 45 Watt RMS Amplifier. Because of theFlexible design, the Paging unit is only required where you need paging. Each Paging Unit and Amplifier is Dip Switch Setwith a Unique Address during installation, so that each unit can be Individually or Globally Controlled.
The Paging Mixer usesany Low Impedance
Dynamic Push to Talk Microphone
MULTIZONE PAGING UNITS
The Multizone Paging Mixer isfully described in a Separate Leaflet
"Multizone Paging Mixer"
45 WATT MULTIZONE AMPLIFIERStereo or Mono Operation
USING RS 485 ELIMINATES HOME RUNNING WIRES BACK TO THE SOURCEIn addition to overcoming the limitations of the RS 232 method, RS 485 allows Multiple Units to be installed over greaterdistances.
,Nigel B Design, Inc. California, USA. Tel: (818) 487-9323 Fax: (818) 766-9805Web Site: www.nigelbdesign.com. E-Mail: [email protected]
With no Limitation on the Number of Zones that can be Created
Part # Description List Price
NB-485MZA Multizone Amplifier with RS 485 Interface $449.95
NB-PS75 Power Supply For Amplifier 120 v -12v AC 4.5 amps $ 49.95
DAISY CHAINING THE AUDIOA similar method is used to provide Audio at each Station or Zone, or Indidual Zones can have its own Audio Souce.
PLENUM RATED EQUIPMENT BOXESMeeting NEC & UL Code Requirements for the Installation of Equipment
and Power in the Plenum or Ceiling Space
COOLING THE EQUIPMENT INSTALLED INSIDE
1. The NB-PLWB comes with a Flat Surface/Wall Mount, allowing the Plenum EquipmentBox to be attached to any Flat Surface or Suspended using our new Hanging Kit.
It's 14” x 14” and almost 5” high allow many different types and sizes of equipment to be installed inside itsextremely Strong Aluminum Interior. For example, some of themany products from Companies such as Crestron®,
AMX ®, Altec Lancing Commstar®, Extron® and all Nigel B Products etc, have been Installation Tested
PLENUM EQUIPMENT BOX MOUNTING OPTIONS Plenum Equipment Boxes can be installed anywhere. The examples belowgive you some idea how flexible the new units are:
THE PLENUM EQUIPMENT BOX WEIGHT CAPACITYThe Box is made from .060" Superior Grade Aluminum and each Mount is made from 16 ga Steel. The Plenum Equipment Box and its Mounts willeasily take a combined weight up to 50 lbs.
We use Conventional Cooling Methods for cooling. The Pole Mount version allows air intake through the bottom of the Pole and exhausts any warm airfrom the Plenum Box through the top of the pole. Slots in the top and bottom of the Flat Surface Mount allow air to pass through the unit. This we callthe Chimney Effect which allows the inside of the Plenum Box to remain cool.
Model NB-PLWBPlenum Equipment Boxwith Flat Surface Mount
attached
NB-PLHKOptional Hanging Kitis UL & CSA Listed
3. The NB-PEBPM Pole Mount Plenum Box attaches to any 1 1/2" Pipe,used to Pole Mount most Projectors.
WIRING AND CABLE ENTRYMore than enough Wiring and Cable Entry and Exits Ports are provided. For the Pole Mount Version, most Cables are run inside the Pole. In addition1 Port is for Power and an additional one is available for other uses. For the Flat Surface Mount/Hanging version, one is used for Power and twoadditional ports are available for connection to 1/2" conduit.
i
2. Our new Hanging Kit in conjunction with the NB- PLWB allows the entire Plenum EquipmentBox to be suspended directly above the Projector above the Ceiling Tiles, or anywhere in theCeiling Space when the Cables are attached to a structural Member to NEC Code Requirements.Each Cable is rated up to 65 lbs.
Flat Surfaceor Wall Mount
1 1/2" Pole Mount
Please turn over for Pricing and other Information
Power OutletBuilt In
(see Over)
Power OutletBuilt In
(see Over)
Pole Mounted Plenum Box Flat Surface/Hanging Plenum Box
Interior Viewsshowing some
equipment installed
Cover is easily removedfor access at any time
Need more outlets for your equipment?(see solutions on next page)
See Also our new Ceiling Tile Kit
Perfect when Mounting the Projector Below
Nigel B Design, Inc. California, USA. Tel: (818) 487-9323 Fax: (818) 766-9805Web Site: www.nigelbdesign.com. E-Mail: [email protected]
IF YOU NEED TO INSTALL THE PLENUM EQUIPMENT BOX BELOW THE CEILING TILES
In order to meet NEC and State Code regulations, it is important to understand the main parts of the Code that regulate how equipment and wiring canbe installed in a Plenum or Ceiling Space.NEC ARTICLE 400-8 and 400-8(5)......page 219 of the code states: That Flexible Cords and Cables are not permitted to be run through Walls,Structural ceilings, Suspended Ceilings, or Dropped Ceilings. In addition the revision to 400-8 specifically prohibits these cords being used withoutbeing properly enclosed. Regulations also prohibits the Installation of open Power Outlets in these spaces.
installed Inside all Plenum Boxesto meet NEC Code Requirements
Eye Bolts are attached to eachcorner of the Plenum Box
The Hanging Kit is UL & CSA Listed and israted with a safe working load of 100 lbs
Using the supplied Flat Plate allowsthe Plenum Box to be fixed to any Flat Surface
To Ceiling Speakers
Power Supply to Projector
Line In to Amplifier
CONTROLLING NIGEL B AMPLIFIERSOur Standard Amplifiers are usually controlled using the Projector's Remote, our Plus Series Amplifiers have an RS 232 Port, enabling them to becontrolled by an AMX® or Crestron® or similar Touch Screen
Because the Pole Mounted Plenum Box uses standard 1 1/2" Pipe fittings, the equipment box can be attached to the Projector's Pole
SPECIFICATIONSInterior Dimensions: 14" x 14" x 4.75 High. Weight: 5 lbs
Pole Mount Installation Hanging Plenum Box Installation
By removing the supplied Port Plugs,standard 1/2" Conduct can be usedto provide Cable Entry & Exit Points
Port Plus fittedboth Sides
Our Plenum Box encloses all Wiring and Cables includingthe Power Recepticle meeting all NEC Code Requirements
The Supplied Power Outlet is
Need more outlets for your equipment?
Simply add one or two 3 Outlet Taps or a Power Strip to the receptacle inside
Part # Description List Price
NB-PEBPM 14" x 14" Plenum Equipment Boxwith Pole Mount $ 299.95
NB-PLWB 14" x 14" Plenum Equipment Box with Flat Surface Mounting Box $ 299.95
NB-PLHK Hanging Kit with all Hardware for Flat Surface Mounting Box $ 79.95
Please see Ceiling Tile Kit Leaflet when using a Projector with the Plenum Equipment Box
2RU RACK MOUNT PLENUM EQUIPMENT BOXPOLE OR HANGING VERSIONS AVAILABLE
Part # Description List Price
NB-2RUBPM 19" wide x 14 " Deep 2 RU Plenum Equipment Box with Pole Mount $ 399.95
NB-2RUPLWB 19" wide x 14" Deep 2 RU Plenum Equipment Box with Flat Surface Mounting Box $ 399.95
NB-PLHK Hanging Kit with all Hardware for Flat Surface Mounting Box $ 79.95
CEILING PANEL KITFOR USE WITH THE
NIGEL B PLENUM EQUIPMENT BOX
INTERNALPOWER OUTLET
ALL CABLES FROM THE UNDERSIDE ARE ROUTED
INSIDE THE ENCLOSED CHANNEL& ENTERS DIRECTLYINTO THE INTERIOR
OF THE PLENUM BOX
CEILING PANEL CAN BE POSITIONED LEFT OR RIGHT OR REVERSEDPROVIDING MULTIPLE PROJECTOR POSITIONING
CABLES ARE ROUTED INSIDE THE ENCLOSED CHANNEL
& ENTER THE PLENUM BOX
The Ceiling Panel and the Plenum Box are made of Light weight Aluminum . The Ceiling Panel is first hung using our Ul Listed 100 lbssupplied Hanging kit. The modified Plenum Equipment Box is then mounted on top and attached to the suspended Hanging Panel.
PLENUM EQUIPMENT BOXACCESS BOX IS SCREWED TOTHE PLENUM BOX
HANGING KIT HOLES AT EACH CORNER(Wires not shown)
Meets NEC and State Building Codes when used with the Nigel B Design Plenum Equipment Box
(As all wiring and the AC Receptacle is enclosed)
CONDUIT ACCESSTO TAKE SPEAKERS WIRES
PROJECTOR MOUNTING PLATE
This providesa tight installation to the Ceiling TileDual Tracks allow the Projector Mounting Plate
to slide along the underside of the trackfor an almost variable positioning of the Projector
WEIGHT 6LBS APPROXLess than half the weight of any competing productPlenum Equipment Box 14" x 14" 5.75" 8 lbs
(See next Page)
Please turn over for more information and List Prices
Nigel B Design, Inc. California, USA. Tel: (818) 487-9323 Fax: (818) 766-9805Web Site: www.nigelbdesign.com. E-Mail: [email protected]
KNOCK OUTS ON THE CEILING PANEL PROVIDES *10DIFFERENT POSITIONS ALLOWING THE PROJECTOR
TO BE POSITIONED TO SUITTHE USERS REQUIREMENTS
* CEILING PANEL CAN BE REVERSED
THE SUPPLIED PROJECTOR MOUNTING PLATE
POSITIONING THE CELING PANELThe Ceiling Panel is hung using the supplied 100lbs UL ratedHanging kit. With a total wieght of only 14lbs the Installer has84lbs for the Projector and any equipment that needs to befitted inside the Plenum Equipment Box.
The Ceiling Panel can be reversed, and also moved fromleft to right, so the Installer can position the Projector inmany different positions
KNOCK OUTS
UNDERSIDE(Room View)
UNDERSIDE
Attaches to the Ceiling Panel using (4) Bolts and Nutsallowing the Plate to slide along the (2) channels andprovide for any cables or wiring to be routed directly to thePlenum Equipment Box.
SUPPLIED KIT COMPRISES1. Ceiling Panel1. Hanging Kit1. Projector Mounting Plate1. Plenum Access Box1. Cable CoverNecessary Hardware
Note: NB-PEB Modified Plenum Equipment Box is an extra charge item
(Room View)
Cables & Wiring routed throught the Projector's Pole & Plate
NB-CTKPL Ceiling Tile Kit for Plenum Box includes Hanging Kit $279.95
NB-PEB Modified Plenum Equipment Box for Ceiling Tile Kit $299.95
POLE MOUNT PLATFORM
SIGNAL CABLES
This versatile 10.5" wide 9.5" deep Platform is designed to accommodate many different pieces of equipment, including, but not limited to, Nigel B Amplifiers,Crestron® QM-RMCRX-BA, QM-RMC, AMX® NI 700 / NI 900 Series, Aurora Multimedia® WACI Controllers and Versa Tools from Extron® .
CABLE MANAGEMENTTo allow all Cables and Wiring to run inside the Pole, the Installer uses two lengths of standard 1 1/2" Projector Pole, one fromthe Mounting to the Coupling on the top of the Platform and one is screwed from the underside Coupling of the Platform to theProjector's Mount, so that no modification to the Poles are required. Now it is not only easier to hide all the Cables from view, italso eliminates the need to tie wrap anything to the outside of the Poles.
The only Platform designed to hold all the Equipment used above a Projector.For Installers, the first Product that also hides all the Cables from view
POLE MOUNT PLATFORMWITH NIGEL B® PLUS AMPLIFIER &
CRESTRON® QM-RMC/QM-RMCRX-BA
POLE MOUNT PLATFORMWITH AMX® NI700
& NIGEL B AMPLIFIER
POLE MOUNT PLATFORMSHOWN WITH PREMIER MOUNT®
& EPSON® PROJECTOR
TO CEILING SPEAKERS
These are just some of the Manufacturers whose products fit perfectly.
POLE MOUNT PLATFORMWITH AURORA MULTIMEDIA
WACI® & NIGEL B AMPLIFIER
Nigel B Design, Inc. California, USA. Tel: (818) 487-9323 Fax: (818) 766-9805Web Site: www.nigelbdesign.com. E-Mail: [email protected]
POLE MOUNT PLATFORMWITH NIGEL B LINE/MIC MIXER& NIGEL B PLUS AMPLIFIER
TO CEILING SPEAKERS
ALL HIIDDEN METHODPOWER WIRING IS RUN
INSIDE THE POLE
POWER CABLE FROMTHE PROJECTOR PLUGS INTO ONE
OF THE 3 POWER PANEL RECEPTACLES
USING CONDUIT FOR EXTERNAL ENTRY OF THE POWER WIRING
SIGNAL CABLES& POWER FROM
THE PLATFORM MOUNTEDEQUIPMENT
RUNS INTERNALLYINSIDE THE POLE
With Built In Three Outlet Power Panel
ALL HIDDEN METHOD
ALL HIDDEN METHOD
POLE MOUNT PLATFORMWITH EXTRON VERSA TOOLS®
CONDUIT HOLECAPPPED OFF
CONDUIT HOLECAPPPED OFF
CONDUIT HOLECAPPPED OFF
ALL HIDDEN METHOD
ALL HIDDEN METHOD
ALL HIDDEN METHOD
ALL HIDDEN METHOD
CONDUIT HOLECAPPPED OFF
CONDUIT HOLECAPPPED OFF
CONDUIT HOLECAPPPED OFF
CONDUIT HOLECAPPPED OFF
P a r t # D e s c r ip t i o nL i s t
P r i c e
N B -P M P P o le M o un t P latfo rm $179 .95
There are two methods of Routing the Power Wiring,1.The Hidden and 2.The Conduit Method.
1. POWER WIRING ENTRY POINT 2. POWER WIRING ENTRY POINT
3 OUTLETPOWER PANEL
1RU SPEAKER UNITFits any 19” Rack
Nigel B Design, Inc, Studio City, CA, 91604 Tel: (818) 487-9323 FAX: (818) 766-9805e-mail: [email protected] www.nigelbdesign.com
Designed to Monitor Audio Amplifiers up to 500 Watts
The new NB-1SPKR is a cost effective solution for Stereo or Mono Monitoring where Rack Space Installation is limited
NB-1SPKR 1 RU S p e ak e r Uni t $ 399.95
With a Superior Sound Quality this 1RU Rackspace 8 Speaker Assembly is the perfect solution for Machine Rooms, Security Surveil-lance, Broadcast and Editing Monitoring, Theme Parks, in fact anywhere its diminutive size is a necessary requirement. Made ofAluminum with a weight of less than 1 1/2 lbs makes the unit perfect for all Mobile applications where its weight saving is a mustsought after feature.
SPECIFICATIONS(8) 4 Ohm High Efficieny SpeakersFrequency:140-20k HzSensitivity (1W at.3m): 85 +- 3 dBWEIGHT & DIMENSIONS:Weight:1.5 lbs1.75” High (1 RU), 19” Wide, 3” Deep
ACCOUSTICALLY DESIGNED SOUND CHAMBERA combination of specially designed Patented High Quality Speakers and our Acoustically Designed Sound Chamber gives ourSpeaker Unit a Quality of Sound never before possible in units of this size.
AVAILABLE LATE AUGUST
HANDLES ANY SIZE AMPLIFIER
OVERLOAD PROTECTION
Our specially designed circuitry protects the speakers from being burnt out when any large Amplifier is connected to the Unit.
To further protect the Speakers when using High Power Amplifiers, and provide the best sound quality, a Front Selector SelectionSwitch allows the user to select the correct impedance load depending on the amplifier being Monitored.
OVERVIEW
A NEW APPROACH TO AUDIO MONITORINGUsing Patented High Efficient Speakers, has allowed us to concentrate on providing the most desirable features of a Studio QualityAudio Monitor into a cost effective design.
CAD DRAWINGSCAD Drawings in both DWX and DFX of all our products are avaible upon request, e-mail: sales @nigelbdeign.com
THE Mk2 LIMPET ALARM
NO FALSE ALARMS WHEN IN USE
AN ELECTRONIC DEVICE FOR PROTECTING EQUIPMENT
Nigel B Design, Inc. California, USA. Tel: (818) 487-9323 Fax: (818) 766-9805Web Site: www.nigelbdesign.com. E-Mail: [email protected]
The Installer has the option to configure the Limpet Alarm to suit different situations:1. Siren and either or both NC or NO Contact Closure Connections.2. Silent with Contact Closure Connection.3. Loop Only.Silent Mode but connected to a Central Alarm System, AMX®, Crestron®, or Aurora Controllers is useful when you
don’t want to alert the thief that the Limpet has been activated.
4 foot Security LoopUser can use any Wire if a longer length is
required
™
MORE THAN A DETERRENT-ABSOLUTE PROTECTION
Plasma Screens, Projectors, in fact anythingyou want to protect from Theft
NC or NO Contact Closure Connectionsthat can be also Connected to any
Central Alarm System
9 Year Battery Life
There are many different types of Equipment that the Limpet will Protect
3. Permantly Bonded to theProjector using the supplied
Plastic Welder
4. Bolted to a Permanent Fixture of theBuilding (Screws or Bolts are Hidden
once the Limpet is closed up)
The Loop Wire exits the Limpetand is then passed through the
Keep Plate& returned to the Limpet
Loop Keep made ofCase Hardened Steel
to Rockwell 60 +. Hacksaw Blade slides straight off
IF THE LOOP OR ANY WIRE IS CUT, THE ALARM IS AUTOMATICALLY ACTIVATED
Can also be incorporated intoan AMX®, Crestron®, or Aurora®
Controllers
Built in 117 dB Siren
Tamper Proof Screwsmake it impossible to openwithout the Special Wrench
(supplied)
Battery Test Button and LED Indicator
Virtually impossible to defeat, the Limpet provides a level of protection no other device currently on the market can do,and is 100% better than any Deterrent Device such as a Cable Lock or Cage that can always be defeated in seconds.
TWO METHODS USED TO PROTECT PROJECTORS
1. Static Displays of High Value Equipment.2. Flat Screen MonitorsAre two of the most obvious uses for Projectors, the cost benefits installing the Limpet include:1 .Elimination of the Inconvenience factor of being without the Device2. Eliminates Unnecessary Insurance Claims3. Reduced Insurance Premiums. THE LIMPET CAN BE ATTACHED TO ANY
SURFACE USING CONCEALED SCREWS,BOLTS OR THE PLASTIC WELDER
LOOP WIRE
NONC
NORMALLY CLOSEDOR NORMALLY OPEN
ALLOW CONNECTIONSTO BE MADE TO ANY SECURITY SYSTEM,
AMX® ,CRESTRON® ORAURORA® CONTROLLERS
Part # Description List Price
NB-2LSAS Mk2 Limpet Security Alarm with ContactClosure Connection $ 169.95
RACKFRAME SYSTEM™
Nigel B Design, Inc. CA, USA. Tel: (818) 487-9323 Fax: (818) 766-9805 Web Site: www.nigelbdesign.com. E-Mail: [email protected]
1U RACKFRAME/SHELF
Each RackFrame Shelf is purchased as an "individual" unit, allowing you to add our 1/4 Rack Amplifiers, Modules or Blanking Panels to the Frame exactly as you want them installed.
Fits any 19" Rack Enclosure requiring only 1 U of Rackspace
PREDRILLED FOR ALL NIGEL B™ AMPLIFIERS, MODULES & EXTRON® VERSA TOOLS® UNITS
RackFrame Shelf shown populated with Extron & Nigel B Modules
The RackFrame Shelf is predrilled making installation of any Nigel B™ Amplifier or Module, or any Extron® Versa Tools® Units, a simple matter ofusing (2) 440 x 1/4" long screws to attach the different units to the RackFrame Shelf.
GENERAL NOTES & INSTRUCTIONS A series of eight holes on the Front of the Frame are provided for future units. When installing Nigel B™ Amplifiers and Modules, it will be seen thatone or two Front Panel Screws have to be removed, before attaching the (2) Underneath 440 Screws.1. First remove the top (2) screws from the Amplifier's Front Panel, then using those screws, attach them to the underneath holes.2. Finally replace the Amplifier's "miising" 4.40 Screwswith the supplieid 4.40 1/4" Round Head, attaching them through the appropriate Rack's FrontHoles.
SUPPLIED HARDWARE(4) 10.32 X 1/2" Truss Head Screws are provided with each RackFrame Shelf when attaching the unit to the Rack Rails of any 19" Equipment Rack.Nigel B Amplifiers, Modules and Blanking Panels for installation into the Rack Frame Shelf are supplied with the necessary hardware at the time ofpurchase.
This allows you to fit all 1/4 Rack Nigel B™ Amplifiers and Modules, or any Extron® 1/8 or 1/4 Rack Versa Tools® Modules.You can also add any Custom Made Connecting Panels of your choice.
Underside of RackFrame Shelf showing predrilled Mounting Holes
Part # Description List Price
NB-1USHE 1U Rack Shelf Frame $ 119.95
NB-1BP 1U Blanking Panel $ 19.95