CustomizersMy name is Vlad (Akella). Georgians,

engaged in manufacturing professional

tatoo-machines which are exclusively

hand-made manufacturing. Most of

machines are produced for certain

masters, tailor-made that enables for

tatoo-master, practically, to take part in

the manufacturing process of machines

and get a result which they need.

Most machines are made of steel,

frames soldered with brass or weld-

ed. All parts are original, except the

screws and springs which are bought

separately. Due to the highest quality

components and configuration the ma-

chines meets the highest international

quality standards.

I really like to work in steam-punk

style and techno. But the same time i

pay homage to classical models such

as Bulldog, Diesel, Walker and others,

so i produce it with great pleasure but

the same time introducing something

from me in design. So, in particular,

was born Diesel version, which called

WALL-E because it is very similar to

the cartoon character with the same

name and the machine really has its

own soul.

Akella

Due to the highest quality components and configu-ration the machines meets the highest international

quality standards.

My name is Vlad (Akella). Georgians,

engaged in manufacturing professional

tatoo-machines which are exclusively

hand-made manufacturing. Most of

machines are produced for certain

masters, tailor-made that enables for

tatoo-master, practically, to take part in

the manufacturing process of machines

and get a result which they need.

Most machines are made of steel,

frames soldered with brass or weld-

ed. All parts are original, except the

screws and springs which are bought

separately. Due to the highest quality

components and configuration the ma-

chines meets the highest international

quality standards.

I really like to work in steam-punk

style and techno. But the same time i

pay homage to classical models such

as Bulldog, Diesel, Walker and others,

so i produce it with great pleasure but

the same time introducing something

from me in design. So, in particular,

was born Diesel version, which called

WALL-E because it is very similar to

the cartoon character with the same

name and the machine really has its

own soul.

Liner “Kerosinka”14 rl,6-7v

Liner “Troynik“ 14rl, 6-7v

DaVinci

DaVinci frameLaner and Shader kit 15m, 14rl, 6-7v footswitch-steel, brass and wood.

Classic Walker 15m

Liner 14rl, polishing thermal welding

full set

Liner 18rlBrass spike

Walker framePowerful shader35M, 30mm coil ,7v

Bulldog frame soldering brass liner 14Rl,25mm coil

I

Most machines are made of steel, frames

soldered with brass or welded. All parts

are original, except the screws and springs

which are bought separately. Due to the

highest quality components and config-

uration the machines meets the highest

international quality standards.

Most machines are made of steel, frames

soldered with brass or welded. All parts

are original, except the screws and springs

which are bought separately. Due to the

highest quality components and config-

uration the machines meets the highest

international quality standards.

Most machines are made of steel, frames

soldered with brass or welded. All parts

are original, except the screws and springs

which are bought separately. Due to the

highest quality components and config-

uration the machines meets the highest

international quality standards.

really like to work in steam-punk style and

techno. But the same time i pay homage to

classical models such as Bulldog, Diesel,

Walker and others, so i produce it with

great pleasure but the same time introduc-

ing something from me in design. So, in

particular, was born Diesel version, which

called WALL-E because it is very similar to

the cartoon character with the same name

and the machine really has its own soul.

Frame Bulldog (shader)15M 6-7v

(WALL-E)Diesel frameShader 15M, 6-7 v

Shader Frame Buiidog

15M , 6+7м

Single copy. 100% hand madeShader 13M , 6-7v

S in gle co p y. 100% hand m adeShader 15M , 6,5v

Vasil Laskavy

My name is Vasil Laskavy. I am 35 years

old, 18 of them I’ve been doing tattoos. In

the 2000 I opened my own studio in my

small town, and continue to tattoo. Like

most artists I have always had a love and

thirst for professional tattoo machines,

probably because of this I decided to do

it by myself. I began tattooing as many at

a time in our country, with rotary ma-

chines, but when I first tried the induction,

I realized that this love for life) I assem-

bled a collection of machines of different

engineers which is constantly updated. I

produce only induction machines, each of

them has its own soul or something, its

character, as opposed to rotary ... This is

purely my opinion. I like the classic frame

a lot: Bulldog, Jones, Walker, etc., I use

these forms often and their interpretation

in my machines. I build a frame from a sin-

gle piece of metal and welded frames, and

sometimes use non-ferrous metals, but

still prefer steel. To apply a coating i use

chromium-plating or blueing, less staining.

The coils on my machines usually 26-23

mm, wire is 0,5-0,56. For the hammers

and the base for the induction coils I use

low-carbon steel. I always try to achieve

perfect surfaces.

Since I tattooing by myself so I tune the

machine primarily for myself, although

necessarily I consider the wishes and pro-

fessional features of the master to whom I

make machine. I almost always tests them

after setup and before shipment. Usually

my machine operate in the range 5-6 volts.

From laner I achieve from 114 to 125 Hz

in the load, but sometimes more. Shaders

85-110 Hz. I believe that I found in my life

an exact activity that brings joy to me, and

most important, to many masters use my

machines in their work)

1. Fill, welded steel _, the load on the 5V 105gts, 5-11M2. Fill, team-_ steel, brass, in the load on the 6B 97gts, 5-15M3. Shader, welded steel _, the load on 5.5V 90Hz, 5-15M4.Fill, wholly steel _, the load on the 5V 89gts, 5-15M5. Liner, Wholly steel _, the load on the 5V 120Hz, 3-9Rl6. Redness, machined steel frame, the load on the 6B 100hz, 5-15M7.Liner, welded steel _, the load on the 5V 123Gts, 3-11Rl8.Fill, machined steel frame, the load on the 5V 95Hz, 5-15M

1

2

3 4

5

6

7

8

1, Laner, machined steel frame, the load at 5-5.5 In 119Hz, 5-11Rl2. Shader machined steel frame, the load on the 5V 95Hz, 5-15M3. Shader, machined steel frame, the load on the 5V 90Hz, 5-15M4. Shader, machined steel frame, the load on the 5V 100hz, 5-15M5. welded steel _, the load on the 5V 90Hz, 5-15M6. Laner, machined steel frame, the load on the 5V 119gts, 3-9Rl7. Laner, welded steel _, the load on the 6B 119Gts, 3-11Rl

2

2

1

3

5

4 6

7

Aleksandr“make pain”

MizurovI started making tattoos in 2007 before it I was interested in drawing and graffiti. First I bought Chinese equipment but because of its bad quality I had to delve into it and repair all the time. So it was my first acquaintance with the technical side of the issue.

A few years later I started working with my friend and mentor in a specialized tattoo studio. You devel-op much faster when every day you have the opportunity to observe the more experienced tattoo mas-ter working. Due to the possibility I have gained useful experience as well in tattooing as in building tattoo machines. Also to develop as a tattoo machine builder I have read a lot on forums and communicated with other builders. But in any case, the proof of the pudding is in the eating, and I have learned a lot by my own mistakes. When you work by your own tattoo machines, you clearly see how it should work and how it should be set. And you can find the right settings not only for yourself but also for others.

I have worked by rotaries and induction machines. Each of the devices has its advantages and I

cannot advise anyone one or an-other device. As for me, I prefer to

work by induction machines and for now I build only them. I would like

to create rotaries too but finding high-quality materials for them is

very difficult. Perhaps in the future the situation will change. New day

brings new techniques and ideas in tattoo machines building.

If I have time I visit different tattoo festivals and conventions where I

communicate with machine build-ers and tattooers and offer my

equipment. For now I’m glad that I can offer my equipment to great masters from different cities and

countries.

Prices for cars from $ 200, and I think then there are no limits. The price

depends on the quality of materials and the time spent on production.

Liner. 3 options.

1 9rl-pc machine and the speed of the part a little soft for the correct appli-

cation of pigment thin needles so that there was no sag under the skin

7-pc-18rl this kind of powerful cars and peppy for tight Welding of the

broad band so that there were no gaps in the line

3 18rl-rs, the machine is suitable for both thin and for the broad lines, pow-

er cars set the voltage, manufactured exclusively for professionals who can

properly make fine lines in such a way so as not to sag formed

shaders.basically it is the machine for 5-25 magnums needles, data sets quickly and smoothly to make a smooth pass-ing shadows are not particularly trau-matizing the skin, due to the broken skin minimally visible all the nuances of black and gray work3 types of paint overpleasant shade-reddening mainly 5-15magnum, this type of machine can be continuously applied color transi-tions in theredness 5-15 or 11-25 magnum tightly and accurately hammering color so that would not be following of the first passes needle points and gapsPixel is painted over 5-35 magnum makes slow and powerful blows to the individual operating points such cars are designed for dense rough color and for individual types of Old School

I’m engaged in tattoo machines producing

and tattooing. Although in the drawing I am

not a profi but from childhood I loved to draw

and analyze everything. House was always

full of hand tools. My father was a mechanic

and had tattoos so apparently I absorb this

stuff. I start tattooing in school, in 5th grade (

it was 1989-90) with the simple needle. A lit-

tle later I began to make my first rotors from

the wind-up razor Tourist. Tape recorders

were rare this time and more over players

and motors was not so easy to get so I used

electric razors, then the motors of the play-

ers. The 1990s have brought into the country

more information from the west and on the

photos of the punk rock groups there was an

alternative to prison stripes. Then service in

the army...of course not without walk of life.

In 2000 I bought my first induction into the

tattoo salon SPIRIT OF DRAGON in Grodno

together with self-made unit that goes to

this days so as machine does.

And to this day I can not part with my walk

of life. Drawing is on the third plane now.

From the childhood i don’t like the same

things as everybody. I like to make and

remake everything by my own style. I’m

trying to search and find interesting solu-

tions and designs in everything. I do not like

routine and i always make something new.

commerce is not the leader of goals. The

machines are built by my own taste. Some-

times I make the machine on someone’s

request. I like brutal style and look. I use all

that comes handy. i don’t stamped spring.

For each machine I cut its own spring

and the firing pin. I braze all frames with

oxygen propane torch, brass or solder with

15% silver content. Now with the advent of

the laser there is the opportunity to make

machines standard. Winter is coming and I

have something to do during it.

PAVELPACEVICH

Painting . indications in the load with 11m - 95Hz, 62%, 6.5. weight 250 g. Vork hors springs, coil 25h9. o.6 wire.

Painting .75-80 Hz and 70-75%. In 6-6.5. optimum weight, the perfect bal-ance. indications in the load. Painted as a felt-tip pen

Experimental machine. 2 rear, of thin springs of hours as alternative to the single thick.

100H42H6-8. P2 COIL 8 LAYERS UNDER VARNISH, RAMA STEEL SPRINGS HORSE.

Peen doused with silver.

SHADER

Painting 15m. in the load - 90Hz, 60%. 6.5V is not a lot of weight, excellent balance.

Powerful line. Frame steel, cop-per processing, thermal bluing. Coils wear sleeve 12 gauge.

Has left for the prize for LVOVSKII FEST. So it is not clear where and to whom.

Circuit. All my circuit for the main groups of 115 - 125 Hz with a needle 55-65%

RavilRUBA

Ilchenko

Most of the items that I use purchased on

the radio market (for rotors mostly) use the

old stuff

For example, ancient coins, will use on the

rotors, I will try to preserve the natural

herbs that they stayed with the excavation.

ZHENYA“JACK”

MURZO

And as it often happens - the first attempt

came out lumpy. At the same time we

didn’t stop and continued to mold what we

had in the studio. After a four assembled

machines we have something like a real

tattoo machine. All this we put up for public

display in a social network. At one time I

was subjected to criticism by the renowned

Builder, who said, “Either you treat this

matter seriously or give up this stupid

venture.” Preiesly from this place moment

I set myself the goal to prove that I am not

worse than others.

As time went on, I learned what others

are doing and trying to do something of my

own. My father helped me a lot. All compre-

hended through trial and error. I realized

that I like it and I want to do next. It was

decided to differentiate themselves among

other so father signed all his products as

´Alexxª, and me, like many teenagers, was

nicknamed as ´Jackª so that’s happened

´Jack & Alexx customsª.

.

A A As far as I lived in a private

Jack & Alexx customs - a young brand

custom equipment for tattooing, a native of

Belarus, which is composed of two people

- a son and a father. We are like Adam and

Seth Tsiferri only by the Belarusian way.

. Our story began in 2011. As time went on,

I delved into the tattoo art reading forums.

At some point, the good people opened my

eyes, telling all my equipment are worth-

less junk. Since my hands are growing

from the right place, it was decided to

revive my Chinese machines. From this our

story begins ...

As far as I lived in a private home my the

father had his own workshop where he

was making for a long time all sorts of

wood products. After gathering all the

information together we have tried to

dazzle machine of what we had ... or rather

blinded by her father, I just watched.ucts. After gathering all the information

liner “Pursuit” # 37 needle beams and 9-18 RL RS. in the load: 128Hz, 62dt, working range of 5-8volt. weight of 220 grams. Price $ 200

Paint over \ shadow economy. # 45 needle 5-15M. in the load: 110Hz, 55dt, working range of 5-8volt. weight 180 grams. Price $ 200

switching power supply 1.2-11.6 volts. maximum load current of 3 amperes. short-circuit protection. The body is made of wood (oak) + cover duralumin. multiturn. voltage indicator. Price $ 150

er range of tattoo equipment manufac-

ture, assemble a powerful team of fans

of their business and continue to develop

custom

Each should have its own “trick” so we have

it. This is the power supply to discharge

indicators IN-14. The idea came after I saw

the prototype unit on the IN-14 tubes from

guys from tattooartists.ru. It was decided

to try to make the same. The first unit we

made in coloboration with N. Ryseykinym.

The bloc had impressive size and was quite

heavy due to the 3-ampere transformer

in it. Presentation of the block was suc-

cessful. There was a lot of comments and

feedback. Later, the unit has been exposed

along with its unit on The Second Interna-

tional Tattoo convention in Moscow, and a

little later the unit was awarded the prize in

one of the nominations on The 11th Tattoo

Festival in St. Petersburg.

The second unit was produced in collo-

boration with Anton ANTech. Now it was a

switched-mode power supply, in 3-4 times

less in size as well as by weight. The proj-

ect ´DaVinciª is a block which part of the kit

in a steampunk style.

About plans for the future.Well, we do

not stand still and try to improve ourselves

in all directions analyzing the market.

There is still a lot of interesting discoveries

ahead! In the future we plan to cover a wid

Steel pedal. Hand engraving.

Left Loop # 54 in the load: 120Hz, 52dt, working range of 5-8volt. weight of 209 grams. Price $ 200

IGORSAVINKOV

Hi! Like many of us I started with a little motor

from a tape recorder, strings and electric

shaver. First induction machine I made in

2006 and to my surprise everyone liked it

immediately))). Dima Chicai said that I should

not stop, so I don’t stop))). I prefer to make

frame from steel, bronze, brass, and com-

bine these materials. Brazed: brass, bronze,

copper, steel. Welded: steel. Wholly: from any

material. Under the order machines I make

according to the customers’ wishes (config-

uration, material, sketch). Decoration part I

make basically manually using grinders and

drilling machine. I prefer non-alloy steel of

one and the same brand for the strikers and

cores (coils). I put small silver ball on the

contact screw for better contact. I use contact

silver, it’s much stronger than the jewelry. In

general, I don’t make just bolts and coins))). I

don’t adhere any style cos my machines very

different from others the way they are.

The most important thing is that machine

will not disturb master with its protruding

corners and heavy weight, and it should

work stable. Basically my machines work in

the range from 3 to 8 volts. Shader speed is

90-95 strokes under load. The rate of liner is

100-120 beats under load.

Clear, “velvet” beat in the presence of worthy

power supply and conductors (pedal,klip-

kord). Unit need to be not less than 2A

and thinner wires are 0.75 mm / 2 for any

SERGEYMACHINIST

4

Shading is designed for a large group of needles rabotet virtually silent, very quiet. Material steel.

Machine is made in the style (Steampunk). The liner machine.The liner machine, one-piece frame milling, easy, very handy when work-ing.

The liner machine. Designed for free piercing the skin in a single pass. Peen heavier. Frame machined, locking pipe

clamps of different sizes.

Shader for large magnums.

Contouring machine, steel welded frame. Normal car for everyday use.

universal tattoo machines

Weight 190 gr. I only do powerful machine equipment intended large groups of needles.

Last pedal with Lenin. Very easy for someone who travels a lot for tattoo festivals.

Liner

Right contouring machine, top firing pin spring is embedded in a certain angle, so as not to bend it, do not change the structure of the metal. Right frame Italian Dino Casarin. I ordered it 10 frames very excellent quality.

DENISSIMONOV

Standard shader 90Hz hard, soldering brass, laser cutting of the frame

powerful Linert115Hz in the load

Liner for accurate strips 3RL to 9RL, standards 115Hz

LinerLiner, confidently pushes large needle from 9Rl

Frames for my induction machines are made

of structural steel, and for rotary made

of special duraluminium by wholly, parts

for soldering frames are hand made and

all the vital parts of the cores for coils are

brisk, contact rack, cams, etc. are made

on precision CNC machines. Reels for all

machines I wind by myself personally on

special equipment, solder and then put the

correct capacitor capacitance. All machines

I assemble and tune by myself. About 30% of

the machines are assembled by order with

specific settings for the master.

Machines are ready to work on any skin, any

thicker and liquid paints. There are several

types of machines, they are designed for

different types of work like liner, shader,

shadow (Black & Gray shader) and for differ-

ent configurations of needles.

Each machine is equipped with spare springs

and a box for storage and transportation.

All induction machines are permanent guar-

antee for the original owner!

SERGEYKUZNECOV

ADAMMOSKAL

After the appearance of my first induc-

tion machines of Chinese origin, fairly

undergoing coronary rebuild appeared

my first desire to try to do something like

that. It seems kike just take and make,

what’s the problem? The first impres-

sion of ease of creating a tattoo machine

vanished in a moment when it came to

practice. Thoughts are more fluid and light

than our reality. Simple mechanism of

induction-machine, nothing fancy - coil-

spring-hammer .... everything ... but just in

this simplicity lies the weight of technical

points, on which depends the quality work

of tattoo machines. It took a lot of time,

experimentation, very hard work, spiritual

and material resources before I got the

results sought by the right-tuned machine

for noninvasive pigment infliction in the

skin, in order to restore the skin after the

procedure took place in low time. In each

machine I to put my heart. Good machines

are for good people.

Painting. 7-15 m.90 Hz. in the load. Painted steel frame. 26mm-reel

liner-shader. Weight 150g. milling frame with D16T (duralumin used in shipbuilding, aircraft building, in the power structure of the aircraft, the aircraft skin,) ____26mm coil.

Liner. -S 26mm coil. Steel frame brazing brass. Weight-200 grams.

Powerful paint. Confidently pushes 9 to 15M. Under load, with voltage 6v

Liner Frame-brass (casting). Coils-31mm, 8ryadn. Chemical coating by means of oxidation. 125Hz / 54 Duty ---- Weight-260g

Shader. Frame-brass (casting), patination.

The frame is made of D16T. Machine weight 150g. Coverage - anodizing. -S 26mm coil. Easy and practical machine.

From the series “Bulldog” --- Liner. Milled. steel frame

Soft painting

Liner. - “Infinini”-steel frame, 26mm-s coil.

Lifetime warranty, 1 year, free re-placement springs. As however for all my production machine

Liner - a compact nice car on the classic frame - (205gramm) 26mm-reel. Steel, brass brazing.

Powerful painting. 26mm coil-

Liner “Spiculum” / 3-7Rl / Steel. Pike. The copper plating. Machine weight 165 grams. 26mm coil.

Gold A “-Liner, 125 Hz to load a 3-7rl.Ves machines - 190 gr. As one possible use of the permanent