CAT. 0119-GB - Gemot Group Valves.pdf · CAT. 0119-GB UNI EN ISO 9001 ... according to UNI EN ISO 9001 and UNI ISO/TS 16949. ... 1” 16 19 0.75 200 53 25 3625 100 14500 11

CAT. 0119-GB

UNI EN ISO 9001Cert. n° 2905ISO/TS 16949

Check Valves

�

Check Valves

�

• Check valves for hydraulicsystems.

• Valve seal in NBR Nitrile Rubber(VU series).

• Available with female threads,male threads and in compactversion.

• Standard crack pressure 35 kPa(5 PSI).

• Other settings availableup to 950 kPa (138 PSI).

• Available in AISI 316 StainlessSteel.

• VU...S Series (throated check valves) designed to guarantee aminimum calibrated flow in onedirection by purposely dimensionedorifices.

• Standard crack pressure 35 kPa(5 PSI).

• Other settings available up to950 kPa (138 PSI).

• Available with female threads,male threads and in compactversion.

• Valve seal in NBR Nitrile Rubber(VU series) for a total sealing.

• Metal sealing valve (VUC series).• Available in AISI 316 Stainless

Steel.• Available VU... S Series throated

check valves.• Update kits available to modify

the crack pressure.

Features

• Check valves are used as a safetydevice in hydraulic systems.

• Specifically designed to bemounted in hydraulic plantswhenever it is necessary toshut-off the line at the presetcrack pressure.

• Characterized by a special valvewith elastomeric seal in NBR(Nitrile Rubber) to guarantee anexcellent sealing action underevery working condition.

• Standard versions are assembledwith a spring set to open the valveat a pressure of 35 kPa (5 PSI).

• Other settings are available up to950 kPa (138 PSI) and also kits toupdate the crack pressure.

• Check valves VUC series have aspecial valve with metal sealingextremely resistant and compact.

Applications Benefits

� �

• Improper use and incorrectmaintenance of products withhigh internal working pressurescould cause malfunctioningand damage to personsand machines.Therefore it is necessary tocarefully conform to the simpleinstructions contained in thiscatalogue.For any further information pleasecontact FASTER Research &Development Dept.

• Before using a new check valveplease carefully check all datareported in our catalogues.

• Make sure it is suitable forpressure and flow characteristicsrequested by the applications.

• Verify that threads fit and that theirsealing is correct.

• If necessary replace damagedcomponents with FASTER®

original spare parts.

Recommendations

� �

2

• The recommendations stated in this catalogue do not consider all risk factors in every possibleapplication of FASTER® couplings.

• The final choice of the product isunder customer’s responsibilitywho has to make the selectionaccording to Faster suggestions.

• The customer has to make surethat all requirements of chosenparts are respected, efficiencyis maintened and the end useris informed about useand maintenance operations.

• Faster and its Distributors arenot responsible for damages topersons and machines caused byan improper use and an incorrectmaintenance of products.

• Increase of products’ technicaland functional features is Faster’spolicy. For that reason all data inthis catalogue are not binding.Faster is entitled to modify thespecifications without prior notice.

• All FASTER® products aredesigned and producedin conformity with the regulationsof Quality Managing Systemaccording to UNI EN ISO 9001and UNI ISO/TS 16949.

• They bear the FASTER® logoto guarantee their originand reliability.

• FASTER® products are distributedworldwide through a networkof highly qualified distributors.

• See available item codes in theordering chart.

• As a further help in defining and selecting the most suitableproduct for the specific application please ask and fill-inwith as much information as possible the Product DefinitionForm (mod. A003) sending it back to Faster CustomerService.

Attention! Responsabilities

• Pressure settings could varywithin a range of ±10%.

• In case of seals damage it isnecessary to replace them byFASTER® original spare parts.

�

How to order

��

Guarantee

�

3


• VU... F Series Stainless Steel pag. 9 - 10• VUCC Series pag. 15• Zinc plating with Cr III passivation on the whole range

N O V E L T I E S I N T H I S C A T A L O G U E

�

NEW

Check Valves

4

5

1) Special FASTER® valve with flat seal.2) Made of Steel with zinc plating and Cr III passivation.3) Standard setting 35 kPa (5 PSI).4) Wide range of threads and settings. Also available in AISI 316 Stainless Steel.5) Available kits to update the crack pressure.

F A S T E R ® C H E C K V A L V E S

�

The descriptions and illustrations in this catalogue are for information only and are not binding.

� � � � � � � � � �

��

� �

��

� � �

��

Settingsdifferentfrom the

standard onealso available

Femaleand malethreads

Valve sealin NBR

Nitrile Rubber

Standardsetting35 kPa(5 PSI)

Standardsetting35 kPa(5 PSI)

��

��

��

��

��

��

In the picture

Series VU

VU...M

VU...F

Pressure drop graph:test bench to ISO 7241-2 specifications with ISO VG 32 oilat 40°C (104°F).Materials:- Steel.- On request: AISI 316 Stainless Steel and brass.- Surface treatment:

zinc plating with Cr III passivation.- Springs in C98 Steel.Seals: standard in oilproof NBR (Nitrile Rubber).On request: Viton, Neoprene, EPDM or other seals.Working temperatures:with standard seals in NBR (Nitrile Rubber) from -25°C (-13°F)to +125°C (+257°F).

6

Features

�

• Shut-off system: valve with elastomeric seal

• The elastomeric seal guarantees perfect and reliable sealing• Standard setting 35 kPa (5 PSI)• Other settings and kits to update crack pressure available

up to 950 kPa (138 PSI) (see accessories page 14)• Versions with female threads (VU...F series)• Versions with male threads (VU...M series)• Special versions available on request• Also available in AISI 316 Stainless Steel (see at page 9)• Also available with calibrated orifices (VU...S)

* Safety factor = 1:4 - For static pressure safety factor 1:2

Technical data

�

VU...MVU...F

See at page 14.

Size Ratedflow

Max. workpressure

Minimum burst pressure

Valve Threads

1/4” 04

l/min GPM MPa PSI

DNNominaldiameter

MPa PSI MPa PSI

7250 200 29000 300 43500250 36250250 36250200 29000160 23200110 15950120 1740080 11800

5017 4,5

*mm inc.

7 0.283/8” 06 4350 120 174003068 189,5 0.371/2” 08 5075 140 203003590 23,811 0.413/4” 12 3190 90 1305022140 3717 0.671” 16 3625 100 1450025200 5319 0.7511/4” 20 3190 90 1305022300 79,424 0.9411/2” 24 2900 80 1160020500 132,331 1.222” 32 1885 52 754013700 18550 1.97

❖

Pressure drop values are referred to the standard setting of 35 kPa.The descriptions and illustrations in this catalogue are for information only and are not binding.

Accessories and spare part kit

�

7The descriptions and illustrations in this catalogue are for information only and are not binding.

Available items

�

Size Code Thread Ø A1 (inlet) Thread Ø A2 (outlet) Standards

04

VU 14F 14F 1/4” BSP 1/4” BSP DIN 3852-2-X 50 1,97 19 0,75VU 14FN 14FN 1/4” NPTF 1/4” NPTF ANSI B1.20.3 50 1,97 19 0,75VU 14FJ 14FJ 1/4” JPT 1/4” JPT JIS B0203 50 1,97 19 0,75VU 14FS 14FS 7/16” UNF 7/16” UNF SAE J1926-1 50 1,97 19 0,75

06

08

12

16

20

24

32



VU 34F 34F 3/4” BSP 3/4” BSP DIN 3852-2-X 86 3,39 34 1,34VU 34FN 34FN 3/4” NPTF 3/4” NPTF ANSI B1.20.3 86 3,39 34 1,34VU 34FJ 34FJ 3/4” JPT 3/4” JPT JIS B0203 86 3,39 34 1,34VU 34FS 34FS 1 1/16” UN 1 1/16” UN SAE J1926-1 86 3,39 34 1,34

VU 1F 1F 1” BSP 1” BSP DIN 3852-2-X 100 3,94 41 1,61VU 1FN 1FN 1” NPTF 1” NPTF ANSI B1.20.3 100 3,94 41 1,61VU 1FJ 1FJ 1” JPT 1” JPT JIS B0203 100 3,94 41 1,61VU 1FS 1FS 1 5/16” UN 1 5/16” UN SAE J1926-1 100 3,94 41 1,61

VU 114F 114F 1 1/4” BSP 1 1/4” BSP DIN 3852-2-X 130 5,12 50 1,97VU 114FN 114FN 1 1/4” NPTF 1 1/4” NPTF ANSI B1.20.3 130 5,12 50 1,97VU 114FJ 114FJ 1 1/4” JPT 1 1/4” JPT JIS B0203 130 5,12 50 1,97VU 114FS 114FS 1 5/8” UN 1 5/8” UN SAE J1926-1 130 5,12 50 1,97

VU 112F 112F 1 1/2” BSP 1 1/2” BSP DIN 3852-2-X 145 5,71 60 2,36VU 112FN 112FN 1 1/2” NPTF 1 1/2” NPTF ANSI B1.20.3 145 5,71 60 2,36VU 112FJ 112FJ 1 1/2” JPT 1 1/2” JPT JIS B0203 145 5,71 60 2,36VU 112FS 112FS 1 7/8” UN 1 7/8” UN SAE J1926-1 145 5,71 60 2,36

VU 2F 2F 2” BSP 2” BSP DIN 3852-2-X 160 6,30 75 2,95VU 2FN 2FN 2” NPTF 2” NPTF ANSI B1.20.3 160 6,30 75 2,95VU 2FJ 2FJ 2” JPT 2” JPT JIS B0203 160 6,30 75 2,95VU 2FS 2FS 2 1/2” UN 2 1/2” UN SAE J1926-1 160 6,30 75 2,95

*

*

**

**

**

**

**

CH❖

❖ Size GAS = BSP *On request

mm inc.L

mm inc.


Available items

�


04

VU 14M 14M 1/4” BSP 1/4” BSP DIN 3852-2-X 50 1,97 22 0,87VU 14MN 14MN 1/4” NPTF 1/4” NPTF ANSI B1.20.3 50 1,97 22 0,87VU 14MJ 14MJ 1/4” JPT 1/4” JPT JIS B0203 50 1,97 22 0,87VU 14MS 14MS 7/16” UNF 7/16” UNF SAE J1926-1 50 1,97 22 0,87

06

08

VU 38M 38M 3/8” BSP 3/8” BSP DIN 3852-2-X 51 2 22 0,87VU 38MN 38MN 3/8” NPTF 3/8” NPTF ANSI B1.20.3 51 2 22 0,87VU 38MJ 38MJ 3/8” JPT 3/8” JPT JIS B0203 51 2 22 0,87VU 38MS 38MS 9/16” UNF 9/16” UNF SAE J1926-1 51 2 22 0,87

VU 12M 12M 1/2” BSP 1/2” BSP DIN 3852-2-X 55 2,16 27 1,06VU 12MN 12MN 1/2” NPTF 1/2” NPTF ANSI B1.20.3 55 2,16 27 1,06VU 12MJ 12MJ 1/2” JPT 1/2” JPT JIS B0203 55 2,16 27 1,06VU 12MS 12MS 3/4” UNF 3/4” UNF SAE J1926-1 55 2,16 27 1,06

***

**

***

CH❖


mm inc.L

mm inc.

8

VU...F and VU...M check valves are available with the settings specified below.(Other special settings are available on request).

Check valves with mixed threads are available on request (example VU14M 14MJ = Inlet thread 1/4” BSP => Outlet thread 7/16” UNF).

Settings A standard B C D E F G H I L M O P Q R T U X Y Z

SIZE AVAILABLE SETTINGS

kPa 10 35 50 100 150 200 250 300 350 400 450 500 550 600 650 700 750 800 850 900 950

PSI 1,5 5 7,3 14,5 21,8 29 36,3 43,5 50,8 58 65 73 80 87 94 102 109 116 123 131 138

1/4” 04 X X X X (*) X (*) X (*) X X X (*) (*) (*) (*) (*) (*) - - -

3/8” 06 (*) X X X X X X X (*) X X X (*) X (*) (*) (*) (*) - - -

1/2” 08 (*) X X X X X (*) X X X X X (*) X (*) (*) (*) X (*) (*) X

3/4” 12 (*) X X X X X (*) X X (*) X X (*) X (*) (*) (*) X (*) (*) (*)

1” 16 X X X X (*) X X X (*) X X X (*) (*) X (*) (*) X (*) (*) X

1-1/4” 20 X X X X X X (*) X (*) X X X (*) (*) (*) (*) (*) X (*) (*) (*)

1-1/2” 24 (*) X X X X X (*) X (*) X (*) X (*) (*) (*) (*) (*) (*) (*) (*) (*)

2” 32 (*) X X X X X X X (*) X X X (*) (*) (*) (*) (*) X (*) X (*)

A standard B C D E F G H I L M O P Q R T U X Y Z

(*) On request Example: VU 14F 14F C = 1/4” check valve 100 kPa setting.

Pressure drop graph:test bench to ISO 7241-2 specifications with ISO VG 32 oilat 40°C (104°F).Materials:- AISI 316 Stainless Steel.Seals: standard in oilproof NBR (Nitrile Rubber).On request: Viton, Neoprene, EPDM or other seals.Working temperatures:with standard seals in NBR (Nitrile Rubber) from -25°C (-13°F)to +125°C (+257°F).

Features

�

• Shut-off system: valve with elastomeric seal

• Completely made of AISI 316 Stainless Steel• The elastomeric seal guarantees perfect and reliable sealing• Standard setting 35 kPa (5 PSI)• Special versions available on request


Technical data

�

See at page 14.

Size Ratedflow

Max. workpressure

Minimum burst pressure

Valve Threads

1/4” 04

l/min GPM MPa PSI

DNNominaldiameter

MPa PSI MPa PSI

6525 180 26100 270 39150225 32625225 32625180 26100144 20880100 14500110 1595072 10440

4517 4,5

*mm inc.

7 0.283/8” 06 3915 108 156602768 189,5 0.371/2” 08 4568 126 1827031,590 23,811 0.413/4” 12 2900 80 1160020140 3717 0.671” 16 3263 90 1305022,5200 5319 0.7511/4” 20 2900 80 1160020300 79,424 0.9411/2” 24 2610 72 1044018500 132,331 1.222” 32 1624 45 652511,2700 18550 1.97

❖



�

9

STAINLESSSTEEL

NEW


Available items

�


04

VU 14F 14F 2 1/4” BSP 1/4” BSP DIN 3852-2-X 50 1,97 19 0,75VU 14FN 14FN 2 1/4” NPTF 1/4” NPTF ANSI B1.20.3 50 1,97 19 0,75VU 14FJ 14FJ 2 1/4” JPT 1/4” JPT JIS B0203 50 1,97 19 0,75VU 14FS 14FS 2 7/16” UNF 7/16” UNF SAE J1926-1 50 1,97 19 0,75

06

08

12

16

20

24

32



VU 34F 34F 2 3/4” BSP 3/4” BSP DIN 3852-2-X 86 3,39 34 1,34VU 34FN 34FN 2 3/4” NPTF 3/4” NPTF ANSI B1.20.3 86 3,39 34 1,34VU 34FJ 34FJ 2 3/4” JPT 3/4” JPT JIS B0203 86 3,39 34 1,34VU 34FS 34FS 2 1 1/16” UN 1 1/16” UN SAE J1926-1 86 3,39 34 1,34

VU 1F 1F 2 1” BSP 1” BSP DIN 3852-2-X 100 3,94 41 1,61VU 1FN 1FN 2 1” NPTF 1” NPTF ANSI B1.20.3 100 3,94 41 1,61VU 1FJ 1FJ 2 1” JPT 1” JPT JIS B0203 100 3,94 41 1,61VU 1FS 1FS 2 1 5/16” UN 1 5/16” UN SAE J1926-1 100 3,94 41 1,61

VU 114F 114F 2 1 1/4” BSP 1 1/4” BSP DIN 3852-2-X 130 5,12 50 1,97VU 114FN 114FN 2 1 1/4” NPTF 1 1/4” NPTF ANSI B1.20.3 130 5,12 50 1,97VU 114FJ 114FJ 2 1 1/4” JPT 1 1/4” JPT JIS B0203 130 5,12 50 1,97VU 114FS 114FS 2 1 5/8” UN 1 5/8” UN SAE J1926-1 130 5,12 50 1,97

VU 112F 112F 2 1 1/2” BSP 1 1/2” BSP DIN 3852-2-X 145 5,71 60 2,36VU 112FN 112FN 2 1 1/2” NPTF 1 1/2” NPTF ANSI B1.20.3 145 5,71 60 2,36VU 112FJ 112FJ 2 1 1/2” JPT 1 1/2” JPT JIS B0203 145 5,71 60 2,36VU 112FS 112FS 2 1 7/8” UN 1 7/8” UN SAE J1926-1 145 5,71 60 2,36

VU 2F 2F 2 2” BSP 2” BSP DIN 3852-2-X 160 6,30 75 2,95VU 2FN 2FN 2 2” NPTF 2” NPTF ANSI B1.20.3 160 6,30 75 2,95VU 2FJ 2FJ 2 2” JPT 2” JPT JIS B0203 160 6,30 75 2,95VU 2FS 2FS 2 2 1/2” UN 2 1/2” UN SAE J1926-1 160 6,30 75 2,95

***

***

***

***

***

***

***

***

CH❖


mm inc.L

mm inc.

STAINLESSSTEEL

NEW

11

1) Special valve with metal sealing.2) Compact design.3) Made of Steel with zinc plating and Cr III passivation.4) Wide range of threads and settings.

F A S T E R ® C H E C K V A L V E S

�

Special valvewith metal

sealing

Compactdesign

��

Heavyduty

manufacture

��

Availablewith several

settings

��

� � � �

In the picture

Series VUC


Wide rangeof threads

��

Pressure drop graph:test bench to ISO 7241-2 specifications with ISO VG 32 oilat 40°C (104°F).Materials:- Steel- On request: AISI 316 Stainless Steel and brass.- Surface treatment:

zinc plating with Cr III passivation.- Springs in C98 Steel.Seals: standard in oilproof NBR (Nitrile Rubber).On request: Viton, Neoprene, EPDM or other seals.Working temperatures:with standard seals in NBR (Nitrile Rubber) from -25°C (-13°F)to +125°C (+257°F).

12

Features

�

• Shut-off system: valve with metal sealing

• The metal sealing guarantees perfect and reliable sealing• Standard crack pressure 35 kPa (5 PSI)• Single piece body: extremely compact and robust• Special versions available on request


Technical data

�

Size Ratedflow

Max. workpressure Minimum burst pressure

3/8” 06

l/min GPM MPa PSI

DNNominaldiameter

MPa PSI

5800 160 232004020 5.3

*mm inc.

5 0.201/2” 08 5800 160 232004040 10.67 0.283/4” 12 5800 160 232004065 17.29.5 0.371” 16 5800 160 232004090 23.812.5 0.49

❖


Please contact FASTER Research & Development Dept.


�


Available items

�

Threaded ends

�

Size Code Threaded end A1(inlet) Thread A1 Thread standards

A1Threaded end A2

(outlet) Thread A2 Thread standardsA2

06

08

12

16

VUC 13/ES-13/ES T1 9/16” UNF ISO 8434-2 T1 9/16” UNF ISO 8434-2 38 1,50 19 0,75VUC 13/ES-28/ES T1 9/16” UNF ISO 8434-2 T2 9/16” UNF ISO 8434-2 40,5 1,59 19 0,75VUC 13/ES-1/ES T1 9/16” UNF ISO 8434-2 T3 9/16” UNF SAE J1926-3 38 1,50 19 0,75VUC 1/ES-13/ES T3 9/16” UNF SAE J1926-3 T1 9/16” UNF ISO 8434-2 38 1,50 19 0,75VUC 1/ES-11/ES T3 9/16” UNF SAE J1926-3 T4 11/16” UNF ISO 8434-3 38 1,50 19 0,75VUC 11/ES-1/ES T4 11/16” UNF ISO 8434-3 T3 9/16” UNF SAE J1926-3 38 1,50 19 0,75VUC 11/ES-11/ES T4 11/16” UNF ISO 8434-3 T4 11/16” UNF ISO 8434-3 38 1,50 19 0,75

VUC 13/FS-13/FS T1 3/4” UNF ISO 8434-2 T1 3/4” UNF ISO 8434-2 42 1,65 22 0,87VUC 13/FS-28/FS T1 3/4” UNF ISO 8434-2 T2 3/4” UNF ISO 8434-2 42 1,65 22 0,87VUC 13/FS-1/FS T1 3/4” UNF ISO 8434-2 T3 3/4” UNF SAE J1926-3 42 1,65 22 0,87VUC 1/FS-13/FS T3 3/4” UNF SAE J1926-3 T1 3/4” UNF ISO 8434-2 42 1,65 22 0,87VUC 1/FS-11/FS T3 3/4” UNF SAE J1926-3 T4 13/16” UNF ISO 8434-3 42 1,65 22 0,87VUC 11/FS-1/FS T4 13/16” UNF ISO 8434-3 T3 3/4” UNF SAE J1926-3 42 1,65 22 0,87VUC 11/FS-11/FS T4 13/16” UNF ISO 8434-3 T4 13/16” UNF ISO 8434-3 42 1,65 22 0,87

VUC 13/HS-13/HS T1 1 1/16” UN ISO 8434-2 T1 1 1/16” UN ISO 8434-2 50 1,97 32 1,26VUC 13/HS-28/HS T1 1 1/16” UN ISO 8434-2 T2 1 1/16” UN ISO 8434-2 50 1,97 32 1,26VUC 13/HS-1/HS T1 1 1/16” UN ISO 8434-2 T3 1 1/16” UN SAE J1926-3 50 1,97 32 1,26VUC 1/HS-13/HS T3 1 1/16” UN SAE J1926-3 T1 1 1/16” UN ISO 8434-2 51 2,01 32 1,26VUC 1/HS-11/HS T3 1 1/16” UN SAE J1926-3 T4 1 3/16” UN ISO 8434-3 50 1,97 32 1,26VUC 11/HS-1/HS T4 1 3/16” UN ISO 8434-3 T3 1 1/16” UN SAE J1926-3 50 1,97 32 1,26VUC 11/HS-11/HS T4 1 3/16” UN ISO 8434-3 T4 1 3/16” UN ISO 8434-3 48 1,89 32 1,26

VUC 13/LS-13/LS T1 1 5/16” UN ISO 8434-2 T1 1 5/16” UN ISO 8434-2 52 2,05 38 1,50VUC 13/LS-28/LS T1 1 5/16” UN ISO 8434-2 T2 1 5/16” UN ISO 8434-2 52 2,05 38 1,50VUC 13/LS-1/LS T1 1 5/16” UN ISO 8434-2 T3 1 5/16” UN SAE J1926-3 52 2,05 38 1,50VUC 1/LS-13/LS T3 1 5/16” UN SAE J1926-3 T1 1 5/16” UN ISO 8434-2 52 2,05 38 1,50VUC 1/LS-11/LS T3 1 5/16” UN SAE J1926-3 T4 1 7/16” UN ISO 8434-3 52 2,05 38 1,50VUC 11/LS-1/LS T4 1 7/16” UN ISO 8434-3 T3 1 5/16” UN SAE J1926-3 52 2,05 38 1,50VUC 11/LS-11/LS T4 1 7/16” UN ISO 8434-3 T4 1 7/16” UN ISO 8434-3 50,5 1,99 38 1,50

*

****

**

*

***

**

*

******

CH❖


mm inc.L

mm inc.

T2 T3 T4T1

VUC check valves are available with the settings specified below.(Other special settings are available on request).

Settings A standard B C D E F G H I L M O P Q R T U X Y Z

kPa 10 35 50 100 150 200 250 300 350 400 450 500 550 600 650 700 750 800 850 900 950

PSI 1,5 5 7,3 14,5 21,8 29 36,3 43,5 50,8 58 65 73 80 87 94 102 109 116 123 131 138

14

Spare parts kits for VU series check valves

�

Original spare parts kits for Faster check valves are availablewith detailed instructions for replacement.The kit contains the retaining rings with the specific springfor the required crack pressure.Please refer to the following table for the ordering codes.

Notice: Using the kits it is also possible to modify the crack pressureof the check valves VU series by shifting from a setting to another.This update is only allowed within the setting ranges specifiedin the table below.

ACCESSORIES

Size Check valve Spare part kit (#) Setting range

1/4” 04 VU 14... KIT VU 14F...Among the whole

setting range


setting range

1/2” 08 VU 12... KIT VU 12F...From 10 to 550 kPa From 600 to 950 kPa


setting range

1” 16 VU 1... KIT VU 1F...Among the whole

setting range

1-1/4” 20 VU 114... KIT VU 114F...Among the whole

setting range

1-1/2” 24 VU 112... KIT VU 112F...Among the whole

setting range

2” 32 VU 2... KIT VU 2F...Among the whole

setting range

# For the suffix indicating the setting please refer to the table at page 8.Example - kit code for product VU 34F G set at 30 kPa (43,5 PSI): KIT VU 34F G.


Series VU...F e VU...M

Please contact FASTERResearch & Development Dept.

VUC series spare part kit

��

15

VUCC series

�

Micro check valves, cartridge designcharacterized by a very compact design, VUCC check valvesare suitable for mounting in Metric, BSP or SAE housings.Designed in two versions for radial or axial flow, VUCCcheck valves can be customized for specific housings.For products information and ordering codes pleasecontact our sales offices.

VU... S series

�

Throated check valvesto guarantee a minimum calibrated flow.VU... S series valves are available in several models:• calibrated flow in one direction,

no flow in the opposite one• calibrated flow in one direction

and total flow in the opposite oneFor products information and ordering codes pleasecontact our sales offices.


SPECIALSERIES

BVU series

�

Manifold blocks for check valvesmade of aluminium, BVU blocks integrate severalcheck valves with different settings in order to allowvarious functionalities.Thanks to their modular design, both in termsof settings and threads, a wide range of applicationsis guaranteed.For products information and ordering codes pleasecontact our sales offices.

NEW

All FASTER® quick-releasecouplings are designed andproduced in conformity withthe regulations of QualityManaging System accordingto UNI EN ISO 9001and UNI ISO/TS 16949Standards.They bear the FASTER® logoto guarantee their origin andreliability.FASTER® quick-releasecouplings are distributedworldwide through a networkof highly qualified distributors.

Guarantee

�

Ask for our catalogues

CAT. 0113-I ItalianoCAT. 0113-GB EnglishFF Flat-Face series

CAT

0119

/04/

06-G

B

CAT. 0112-I ItalianoCAT. 0112-GB EnglishAgriculture series

CAT. 0111-I ItalianoCAT. 0111-GB EnglishMultifaster series

CAT. 0110/I ItalianoCAT. 0110/GB EnglishCAT. 0110/F FrançaisGeneral Line

CAT. 0116-I ItalianoCAT. 0116-GB EnglishCPV-CNV and CVV series

CAT. 0115-I ItalianoCAT. 0115-GB EnglishStandard series

CAT. 0114-I ItalianoCAT. 0114-GB EnglishScrew-on couplings series

CAT. 0118-I ItalianoCAT. 0118-GB EnglishRF series

CAT. 0119-I ItalianoCAT. 0119-GB EnglishVU series

CAT. 0117-I ItalianoCAT. 0117-GB EnglishDF series

I - FASTER S.p.A.I-26027 RIVOLTA D’ADDA (CR) Italy - Via L. Ariosto, 7

(+39) 0363.377211 - Fax (+39) 0363.377333www.faster.it - [email protected]

D-BENELUX - FASTER - Jürgen GamersD-40764 LANGENFELD GER - Ursulaweg, 39

(+49) (0) 2173.83924 - Fax (+49) (0) 2173.83925www.faster-germany.de - [email protected]

UK - FASTER - Richard BennettGB-TA18 7BY UK19 Beechwood Drive CREWKERNE, Somerset

(+44) (0) 1460.77020 - Fax (+44) (0) [email protected]

F - FASTER - François DivetF-35200 RENNES - 11, Rue Jean Bras

(+33) (0) 2.99.51.44.94Fax (+33) (0) [email protected]

USA - FASTER Inc.MAUMEE, OH 43537-9505 - 6560 Weatherfield, Ct.

(+1) 419-868-8197 - (+1) 800-231-2501 - Fax (+1) 419-868-8360www.fasterinc.com - [email protected]


Documents

CAT. 0119-GB - Gemot Group Valves.pdf · CAT. 0119-GB UNI EN ISO 9001 ... according to UNI EN ISO 9001 and UNI ISO/TS 16949. ... 1” 16 19 0.75 200 53 25 3625 100 14500 11