CAPACITOR

A device used to store charge in an electrical circuit. A capacitor functions much like a battery, but charges and discharges much more efficiently (batteries, though, can store much more charge).

A basic capacitor is made up of two conductors separated by an insulator, or dielectric. The dielectric can be made of paper, plastic, mica, ceramic, glass, a vacuum or nearly any other nonconductive material. Some capacitors are called electrolytics, meaning that their dielectric is made up of a thin layer of oxide formed on a aluminum or tantalum foil conductor.

(A) Non-polarized fixed capacitor

A non-polarized ("non polar") capacitor is a type of capacitor that has no implicit polarity -- it can be connected either way in a circuit. Ceramic, mica and some electrolytic capacitors are non-polarized. You'll also sometimes hear people call them "bipolar" capacitors.

Unpolarised capacitors (small values, up to 1µF)

Examples: Circuit symbol:

Small value capacitors are unpolarised and may be connected either way round. They are not damaged by heat when soldering, except for one unusual type (polystyrene). They have high voltage ratings of at least 50V, usually 250V or so. It can be difficult to find the values of these small capacitors because there are many types of them and several different labelling systems!

Many small value capacitors have their value printed but without a multiplier, so you need to use experience to work out what the multiplier should be!

For example 0.1 means 0.1µF = 100nF.

Sometimes the multiplier is used in place of the decimal point: For example: 4n7 means 4.7nF.

(B) Polarized fixed capacitor

A polarized ("polar") capacitor is a type of capacitor that have implicit polarity -- it can only be connected one way in a circuit. The positive lead is shown on the schematic (and often on the capacitor) with a little "+" symbol. The negative lead is generally not shown on the schematic, but may be marked on the capacitor with a bar or "-" symbol. Polarized capacitors are generally electrolytics.

Polarised capacitors (large values, 1µF +)

Examples: Circuit symbol:

Electrolytic Capacitors

Electrolytic capacitors are polarised and they must be connected the correct way round, at least one of their leads will be marked + or -. They are not damaged by heat when soldering.

Note that you really need to pay attention to correctly hooking a polarized capacitor up (both with respect to polarity, as well as not pushing a capacitor past its rated voltage). If you "push" a polarized capacitor hard enough, it is possible to begin "electrolyzing" the moist electrolyte. Modern electrolytic capacitors usually have a pressure relief vent to prevent catastrophic failure of the aluminum can (but don't bet your eyesight on this).

Function

Capacitors store electric charge. They are used with resistors in timing circuits because it takes time for a capacitor to fill with charge. They are used to smooth varying DC supplies by acting as a reservoir of charge. They are also used in filter circuits because capacitors easily pass AC (changing) signals but they block DC (constant) signals.

Capacitance

This is a measure of a capacitor's ability to store charge. A large capacitance means that more charge can be stored. Capacitance is measured in farads, symbol F. However 1F is very large, so prefixes are used to show the smaller values.

Three prefixes (multipliers) are used, µ (micro), n (nano) and p (pico):

µ means 10-6 (millionth), so 1000000µF = 1F n means 10-9 (thousand-millionth), so 1000nF = 1µF

p means 10-12 (million-millionth), so 1000pF = 1nF

Capacitor values can be very difficult to find because there are many types of capacitor with different labelling systems!

There are many types of capacitor but they can be split into two groups, polarised and unpolarised. Each group has its own circuit symbol.

REED RELAY & REED SWITCH

A relay is an electrically operated switch. Current flowing through the coil of the relay creates a magnetic field which attracts a lever and changes the switch contacts. The coil current can be on or off so relays have two switch positions and most have double throw (changeover) switch contacts as shown in the diagram.

Relays allow one circuit to switch a second circuit which can be completely separate from the first. For example a low voltage battery circuit can use a relay to switch a 230V AC mains circuit. There is no electrical connection inside the relay between the two circuits, the link is magnetic and mechanical.

The relay's switch connections are usually labelled COM, NC and NO:

COM = Common, always connect to this, it is the moving part of the switch.

NC = Normally Closed, COM is connected to this when the relay coil is off.

NO = Normally Open, COM is connected to this when the relay coil is on.

Connect to COM and NO if you want the switched circuit to be on when the relay coil is on.

Connect to COM and NC if you want the switched circuit to be on when the relay coil is off.

Reed relays

Reed relays consist of a coil surrounding a reed switch. Reed switches are normally operated with a magnet, but in a reed relay current flows through the coil to create a magnetic field and close the reed switch.

Reed relays generally have higher coil resistances than standard relays (1000 for example) and a wide range of supply voltages (9-20V for example). They are capable of switching much more rapidly than standard relays, up to several hundred times per second; but they can only switch low currents (500mA maximum for example).

Relays and transistors compared

Like relays, transistors can be used as an electrically operated switch. For switching small DC currents (< 1A) at low voltage they are usually a better choice than a relay. However, transistors cannot switch AC (such as mains electricity) and in simple circuits they are not usually a good choice for switching large currents (> 5A). In these cases a relay will be needed, but note that a low power transistor may still be needed to switch the current for the relay's coil! The main advantages and disadvantages of relays are listed below:

Circuit symbol for a relay

Reed RelayPhotograph © Rapid Electronics

Advantages of relays:

Relays can switch AC and DC, transistors can only switch DC. Relays can switch higher voltages than standard transistors.

Relays are often a better choice for switching large currents (> 5A).

Relays can switch many contacts at once.

Disadvantages of relays: Relays are bulkier than transistors for switching small currents. Relays cannot switch rapidly (except reed relays), transistors can switch many times per second.

Relays use more power due to the current flowing through their coil.

Relays require more current than many ICs can provide, so a low power transistor may be needed to switch the current for the relay's coil.

Reed Switch (usually SPST)

The contacts of a reed switch are closed by bringing a small magnet near the switch. They are used in security circuits, for example to check that doors are closed. Standard reed switches are SPST (simple on-off) but SPDT (changeover) versions are also available.

Warning: reed switches have a glass body which is easily broken!

LIGHT SENSITIVE SWITCHES

There are a wide range of applications for light sensitive switches: lighting, entrance door, automatic staircase, automatic opening of doors to the action of a ray of light, alarm systems, etc… Many of us are familiar with photosensitive switches made with a single transistor that is controlled by a photoresistor placed between the base and the recharger, depending on what is desired: normal functioning “closed” or normal “open” the switch.

TEMPERATURE OPERATED ALARMS

Thermistor-operated temperature alarm that can ring a bell, turn on a light or ring a buzzer. Any temperature between 115° and 165°F can be detected