Canon Errors 2

Error Code Description

C0030 Fax PWB Problem. Processing with fax software is

disabled due to software or hardware issues.

C0060 Main PWB Type Mismatch Error.

C0070 Fax PWB Incompatability Detection Problem. Fax

software is not compatible with main PWB software.

C0130 Main PWB EEPROM Backup Memory Device Problem.

EEPROM can not be written or read.

C0140 Main PWB EEPROM Backup Memory Data Problem.

Abnormal reading data from EEPROM.

C0150 Engine PWB EEPROM Backup Memory Device

Problem. EEPROM cannot be written or read.

C0160 Engine PWB EEPROM Backup Memory Data Problem.

Abnormal reading data from EEPROM. Read & write

data do not match five times consecutively.

C0170 Copy Counts Problem. A checksum error is detected

in the main and engine backup memories for copy

counters.

C0180 Machine Number Mismatch Error. Machine number

does not match on main and engine PWBs

C0600 Main PWB DIMM Installed Incorrectly.

C0610 Main PWB DIMM error

C0630 DMA transmission of compressed, decompressed,

rotated, relocated, or blanked-out image data does

not complete within a specified period of time.

C0640 Hard Disk Drive cannot be accessed

C0700 Optional CF backup is not suitable.

C0800 Image processing problem. JAM05 is detected twice.

C0830 Fax Flash ROM program area checksum error

C0870 Fax PWB to Main PWB high capacity data transfer

problem.

C0880 Fax PWB program archive problem.

C0920 Fax backup data is not retained.

C1010 Cassette #1 Lift Motor error. Exceeds 12 seconds of

operation or 500ms of overcurrent.

C1020 Cassette #2 Lift Motor error. Exceeds 12 seconds of

operation or 500ms of overcurrent.

C1030 PF-700 optional cassette #3 lift motor error.

C1040 PF-700 optional cassette #4 lift motor error.

C1100 PF-750 (Left) Lift Motor 1 error. Exceeds 1 second

overcurrent.

C1110 PF-750 (Right) Lift Motor 2 error. Exceeds 1 second

overcurrent.

C1120 PF-750 (Left) Lift Motor 1 position problem. PF

switch 2 remains off after 30 seconds of motor

operation.

C1130 PF-750 (Right) Lift Motor 2 position problem. PF

switch 1 remains off after 30 seconds of motor

operation.

C1800 PF-700/PF-750 Communication Problem.

C1900 PF-700 EEPROM error. Write data & Read data are

not in agreement three times consecutively.

C2000 Drive Motor Problem. Stable Off is detected

exceeding 1 sec after motor stability. Stabilization is

not detected with 6 sec of activation.

C2250 Main Charge Cleaner Motor error. Lock error is

detected three times in a row during cleaner motor

operation.

C2500 Paper Feed Motor error. Stable Off is detected

exceeding 1 sec after motor stability. Stabilization is

not detected within 6 seconds of activation.

C2600 PF-700 Drive Motor error. Lock signal exceeds

500ms.

C2600 PF-750 Paper Conveying Motor error. Lock signal

exceeds 450ms.

C3100 Scanner Carriage Problem. Scanner home position

is not detected at initialization or start of copying

from contact glass.

C3200 Exposure Lamp Problem. Exposure lamp does not

reach the input value threshold within 5 sec of

commencing reading.

C3210 Exposure Lamp Problem. Exposure lamp does not

exceed the input threshold value within 5 sec of

commencing reading.

C3300 CCD AGC Problem. After AGC correct input is not

obtained at the CCD.

C3310 CIS AGC Problem. After AGC correct input is not

obtained at the CIS.

C3500 Communication Error Between Scanner and SHD.

C3900 Scanner PWB Backup Memory Read/Write Problem.

Read & Write data does not match.

C3910 Scanner PWB Backup Memory Data Problem. Data

in a specified area of the backup memory does not

match the specified values.

C4000 Polygon Motor Synchronization Problem. Polygon

motor does not stabilize speed within 20 sec of

activation.

C4010 Polygon Motor Steady-State Problem. Stable Off is

detected for 20 sec continuously after polygon

motor stabilization.

C4200 BD Steady-State Problem. ASIC detects a Beam

Detect error A for 2 sec after polygon motor

stabilization.

C5300 Cleaning Lamp Broken Wire. While the cleaning

lamp is On, the broken wire detection signal is

detected for 2 sec continuously.

C6000 Fuser Heater Break. Thermistor1 detected less than

70C/158F for 10 sec during warmup & ready.

Thermistor2 detected less than 40C/104F for 10 sec

during warmup & ready. Temp at thermistor 1or 2

does not rise by at least 1C/1.8F within 5 sec.

C6020 Abnormally High Thermistor Temperature.

Thermistor 1 or 2 is detected 250C/482F for 40ms

or more.

C6030 Fixing Thermistor Break Error. Thermistor break

signal is detected for 1 sec.

C6050 Abnormally Low Thermistor Temperature.

Thermistor 1 is detected 80C/176F or less for 1 sec

continuously during copying.

C6400 Zero-Cross Signal Error. While fuser heater On/Off

control is performed, the zero-cross signal is not

input within 3 sec.

C6410 Fuser Unit Connection Insertion Problem. Absence

of fuser unit is detected.

C6420 Fuser Unit Fuse Cut Problem. The fuse has been cut

33 sec after the fuse cut signal is turned on.

C7300 Toner Container Problem. Toner level is not

detected when toner empty is detected.

C7400 Developing Unit Connection Insertion Problem.

Absence of the developing unit is detected.

C7410 Drum Unit Connection Insertion Problem. Absence

of the drum unit is detected.

C7800 Broken External Thermistor Wire. Thermistor on the

environmental sensor outputs 4.5v or more.

C7810 Short-Circuited External Thermistor. Thermistor

input value is 0.5v or less.

C7900 Drum EEPROM Error. Reading or writing to the

EEPROM cannot be performed.

C7910 Developing EEPROM Error. Reading or writing to the

EEPROM cannot be performed.

C8020 DF-710 Punch Motor Problem. Punch motor lock

signal is detected for 500ms or more during

activation.

C8030 DF-730 Tray Upper Limit Detection Problem. When

tray elevation motor raises a tray, the upper limit

switch detects On condition.

C8050 DF-710 Paper Conveying Belt Motor 1 Error. Paper

conveying belt home position sensor 1 does not

turn Off within 1.5 sec. Paper conveying belt home

position sensor 1 does not turn On within 2.5 sec.

Jam 88.

C8060 DF-710 Paper Conveying Belt Motor 2 Error. Paper

conveying belt home position sensor 2 does not

turn Off within 1.5 sec. Paper conveying belt home

position sensor 2 does not turn On within 2.5 sec.

C8070 DF-710 Internal Tray Communication Error. The

connection is detected, but communication is not

possible with the internal tray.

C8140 DF-710 Main Tray Problem. Main tray is not

detected in not detected by main tray top limit

detection sensor or main tray capacity detection

sensor within 20 sec of ascending. Main tray upper

limit detection sensor or main tray load detection

sensor is not detected as Off within 20 sec of main

tray descending. Main tray lower limit detection

sensor is not detected as On within 20 sec of main

tray descending. Main tray upper limit detection

sensor or main tray load detection sensor remain on

for 2 sec or more during main tray ascent.

C8140 DF-730 Tray Elevation Motor Problem. Tray lower

limit sensor or surface view sensor cannot be

detected within 10 sec.

C8170 DF-710 Side Registration Motor 1 Problem. During

initial rotations home position is not detected within

3 sec. Jam 88.

C8170 DF-720 Front Side Registration Motor Problem.

During initial rotations home position is not

detected within 106 pulses. When the front side

home position sensor is turned off during

initialization, the sensor did not turn on within 3

sec.

C8170 DF-730 Adjustment Motor Problem. Adjustment

motor home position motor is not detected within a

specific time during activation.

C8180 DF-710 Side Registration Motor 2 Problem. During

initial rotations home position is not detected within

3 sec. Jam 88.

C8180 DF-720 Rear Side Registration Motor Problem.


detected within 106 pulses. When the rear side



sec.

C8190 DF-720 Trailing Edge Registration Motor Problem.


detected within 106 pulses. When the trailing edge



sec.

C8210 DF-710 Stapler Moving Motor 1 Error. During initial

rotations home position is not detected within 1.5

sec.

C8210 DF-720 Finisher Stapler Problem. Stapler home

position sensor does not change state from non-

detect to detect within 200ms of forward (CCW)

rotation. During initial rotations stapler home

position detection does not change state from non-

detect to detect within 600ms of reverse (CW)

rotation.

C8210 DF-730 Stapler Problem. Home position is not

detected within a specific time of activation.

C8220 DF-710 Stapler Moving Motor 2 Error. During initial

rotations home position is not detected within 3.5

sec.

C8230 DF-710 Stapler Motor Problem. Jam 82 is indicated.

C8300 BF-710 Centerfold Unit Communiation Error.

Although the connection is detected, communication

is not possible with the centerfold unit.

C8310 BF-710 Centerfold Side Registration Motor 1

Problem. During initial rotations home position is

not detected within 1000ms.

C8320 BF-710 Centerfold Paper Conveying Belt Motor



C8330 BF-710 Blade Motor Problem. During initial rotations

home position is not detected within 1500ms.

C8340 BF-710 Centerfold Staple Motor Problem. Jam 89.

C8350 BF-710 Centerfold Side Registration Motor 2



C8360 BF-710 Centerfold Main Motor Problem. The motor

lock signal is detected for more than 1000ms during

activation.

C8440 DF-730 Sensor Adjusting Problem. The paper entry

sensor cannot be adjusted within the specified

range.

C8460 DF-730 EEPROM Problem. Reading to or writing

from EEPROM cannot be performed.

C8500 MT-710 Communication Error. The connection is

detected, but communication is not possible with

the mailbox.

C8510 MT-710 Drive Motor Problem. The motor lock signal

is detected for more than 500ms during activation.

C8800 DF-710 Communication Problem. No

communication: there is no reply after (5) tries.

Abnormal communication: a parity or checksum

error is detected (5) times in succession.

C8900 DF-710 Backup Memory Data Problem. Read and

write data does not match.

C8910 PH-5A Backup Memory Data Problem. Read and


C8920 MT-710 Backup Memory Data Problem. Read and


C8930 BF-710 Backup Memory Data Problem. Read and


C9000 DP-700 Communication Problem. A communication

error is detected.

C9040 DP-700 Lift Motor Ascent Error. The DP lift upper

limit switch is not detected within 10000 pulses.

After a one time retry, the DP lift upper limit switch

could not be turned On.

C9050 DP-700 Lift Motor Descent Error. The DP lift lower

limit switch is not detected within 10000 pulses.

After a one time retry, the DP lift lower limit switch

could not be turned On.

C9060 DP-700 EEPROM Error. Read and write data does

not match. Data in the specified area of the backup

memory does not match the specified values.

C9070 DP-700 Communication Error between the DP and

SHD. A communication error is detected.

C9080 DP-700 Communication Error between the DP and

CIS. Reading cannot be performed correctly.

CF000 Operation Panel PWB Communication Error/System

Error. Unknown error. Communication error

between panel and main controller. (If CF620

occurred and is left, CF000 also occurred because of

timeout control.

CF010 Main PWB Checksum Error/System Error.

Communication error between panel and main

controller.

CF020 Memory Checksum Error/Operation System Error.

CF030 Main PWB System Error.

CF040 Engine PWB Communication Error.

CF041 Scanner PWB Communication Error.

CF050 Engine ROM Checksum Error.

CF060 Engine RAM Error.

CF070 Flash ROM Error. Defective flash ROM (which?).

CF080 Flash ROM Error (during download). Defective flash

ROM (which?).

CF090 Fax System M Communication Error.

CF14F Power Source Secondary Side Error/Operation

System Error. The operation decomes unstable after

recovering the power supply fail (brownout or

power drop). Wall voltage is unstable or the main

power supply switch was turned OFF/ON within 1

sec.

CF256 Fax System M IOBL error or KUIOLIB error. Poor

contact at the fax card card due to mis-installation.

CF257 Fax System M IOBL error or KUIOLIB error. Poor


CF26F Print System Other Errors. Bug of v.2.03B has been

fixed by v. 2.04A (Booklet > Booklet Print).

CF3xx Undefined.

CF423 Fax System M Error. Wrong data or value detected

when the following function is used. Or poor contact

at fax card due to mis-installation.

CF423 Fax System M Error. The IF error detects during

system authentication from ACT_Account_Manager.

Or poor contact at fax card due to mis-installation.

CF433 CF434

CF437 CF43F

CF441 CF444

CF445 CF451

HDD Image Process Error. Destruction of stored

jobs on the HDD. It may occur when selecting the

keys for calling stored copy or scanner job from a

custom box.

CF45F CF453

CF454 CF45F

CF460 CF463

CF46F CF470




custom box.

CF473 CF47F

CF484 CF487

CF48F CF490

CF493 CF494




custom box.

CF5xx Undefined.

CF610 System Start Error.

CF620 System Error. Error acquiring the event data. Panel

detects CF000 as same error.

CF620 System Error. Error acquiring the event data. Panel

detects CF000 as same error. Unable to Load Files

To CF Card.

CF7D7 Readout Error of SSL (authentication data).

CFAxx HDD Error.

CFB2C CFB30

CFB31

Panel Error. NetFont error. Communication error

between panel and main controller during

initialization or rejection of communication by

controller during initialization. Blue Screen of Death.

CFB30 Incompatible Level Of Firmware on Main EEPROM.

CFB31 Corrupt Firmware on Main EEPROM.

CFB32 Panel Error. Timeout request for start up command.

Start command hasn't been received. Possible

destruction of system file in HDD. Cannot enter

maintenance mode. Blue Screen of Death.

CFB33 Panel Error. Detects disconnection with controller.

Possible overdrive of control board or destruction of

system file in HDD. Cannot enter maintenance

mode. Blue Screen of Death.

F000 Operation Panel PWB Communication Error.

F010 Main PWB Checksum Error.

F020 Memory Checksum Error.

F030 Main PWB System Error.

F040 Engine PWB Communication Error.

F041 Scanner PWB Communication Error.

F050 Engine ROM Checksum Error.

F060 Engine RAM Error.

F070 Flash ROM Error.

F080 Flash ROM Error (during download).

F090 Fax Control PWB Communication Error.

F14F Power Source PWB Second Side Error.

E00000 or U00000 Fax Communication Error: No response or line busy

after the set number of redials.

E00100 or U00100 Fax Communication Error: Transmission was

interruped by a press of the Stop/Clear key.

E00200 or U00200 Fax Communication Error: Reception was

interrupted by a press of the Stop/Clear key.

E00300 or U00300 Fax Communication Error: Recording paper on the

destination unit has run out during reception.

E00420 or U00420 Fax Communication Error: A relay request was

received from the host center but interrupted

because of a mismatch in permit ID or telephone

number.

E00421 or U00421 Fax Communication Error: Subaddress-based relay

reception was interrupted because of a mismatch in

the specified subaddress relay box number.

E00430 or U00430 Fax Communication Error: Polling request

(confidential or reverse polling) was received but

interrupted because of a mismatch in the permit

number.

E00430 or U00430 Fax Communication Error: Subaddress-based

bulletin board transmission was interrupted because

of a mismatch in the permit ID of the transmitting

unit.

E00431 or U00431 Fax Communication Error: Confidential polling

transmission was interrupted because the specified

confidential box number was not registered.

E00431 or U00431 Fax Communication Error: A subaddress-based


the specified subaddress confidential box was not

registered.


transmission was interrupted because of a

mismatch in the confidential box ID number.

E00432 or U00432 Fax Communication Error: A subaddress-based


of a mismatch in the subaddress confidential box

number.


request was received but data was not present in

the confidential box.


bulletin board transmission request was received

but data was not present in the subaddress

confidential box.


request was received but interrupted because the

specified confidential box number was intended for

encryption.



specified confidential box was being accessed.


bulletin board transmission request was received

but interrupted because the specific subaddress

confidential box was being accessed.

E00440 or U00440 Fax Communication Error: Confidential reception

was interrupted because the specified confidential

box number was not registered.


confidential reception or subaddress-based relay

reception was interrupted because the specific

subaddress box was not registered.


confidential reception or subaddress-based relay

command reception was interrupted because the

specific subaddress box number was being

accessed.

E00441 or U00441 Fax Communication Error: Confidential reception

was interrupted because the specified confidential

box number was intended for encryption.

E00450 or U00450 Fax Communication Error: The destination

transmitter disconnected because the permit IDs

did not agree while the destination transitter is in

password-check transmission or restricted

transmission.

E00460 or U00460 Fax Communication Error: Encrypted reception was

interrupted because the specified encryption box

number was not registered.

E00460 or U00460 Fax Communication Error: Ecrypted reception


specified encryption box was being accessed.

E00462 or U00462 Fax Communication Error: Ecryption reception was

interrupted because the encryption key for the

specified encryption box was not registered.

E00500 or U00500 Fax Communication Error: Multiple communication

was interrupted and the call was not made on

destination units after interruption.

E00600 or U00600 Fax Communication Error: The document processor

cover is open.

E00601 or U00601 Fax Communication Error: Document jam or the

document length exceeds the maximum.

E00602 or U00602 Fax Communication Error: Image scanning section

problem

E00603 or U00603 Fax Communication Error: No document feed.

E00604 or U00604 Fax Communication Error: Document length

exceeded the limit of the bitmap memory capacity.

E00610 or U00610 Fax Communication Error: Recording section cover

open.

E00611 or U00611 Fax Communication Error: Recording paper jam.

E00613 or U00613 Fax Communication Error: Image writing section

problem.

E00614 or U00614 Fax Communication Error: Nearly empty of

recording paper.

E00615 or U00615 Fax Communication Error: Empty of recording

paper.

E00620 or U00620 Fax Communication Error: Copier fixing unit

problem.

E00622 or U00622 Fax Communication Error: Copier drive motor

problem.

E00655 or U00655 Fax Communication Error: CTS was not activated

after RTS due to a modem error.

E00656 or U00656 Fax Communication Error: Data was not transmitted

after CTS was activated due to a modem error.

E00670 or U00670 Fax Communication Error: Power was cut off during

communication.

E00677 or U00677 Fax Communication Error: There was no file to

transmit in the memory transmission mode.

E00690 or U00690 Fax Communication Error: System error.

E00700 or U00700 Fax Communication Error: Communication was

interrupted because of a problem in the destination

unit.

E00800 or U00800 Fax Communication Error: A page transmission

error occurred in G3 mode, because of reception of

a RTN or PIN signal.

E00810 or U00810 Fax Communication Error: A page transmission

error re-occurred in G3 mode after retry of

transmission in ECM mode.

E00900 or U00900 Fax Communication Error: A page reception error

occurred in G3 mode. An RTN or PIN signal was

transmitted because of a page reception error.

E00910 or U00910 Fax Communication Error: A page reception error

occurred in G3 mode. A page reception error

remained after retry of transmission in ECM mode.

E01000 or U01000 Fax Communication Error: Transmission in G3 mode

was interrupted by a signal error. An FTT signal was

received for a set number of times after TCF signal

transmissions at 2400bps.


was interrupted by a signal error. An RTN signal

was received in response to a Q signal (excluding

EOP) after transmission at 2400bps.


was interrupted by a signal error. The function of

the unit differs from that indicated by a DIS signal.


was interrupted by a signal error. No relevant signal

was received after transmission of a DNL (MPS or

EOM) signal, and the preset number of command

retransfers was exceeded (between units of our

make).



was received after transmission of a DCS, TCF

signal, and the preset number of command

retransfers was exceeded.



was received after transmission of an NSS1, NSS2

(TCF) signal, and the preset number of command


make).



was received after transmission of an NSS3, TCF



make).



was received after transmission of an MPS signal,

and the preset number of command retransfers was

exceeded.



was received after transmission of an EOM signal,


exceeded.


was interrupted by a signal error. An MCF signal

was received but no DIS signal was received after

transmission of an EOM signal, and T1 timeout was

detected.



was received after transmission of an EOP signal,


exceeded.



was received after transmission of a PRI-EOP signal,


exceeded.



was received after transmission of a CNC signal,


exceeded (between units of our make).



was received after transmission of a CTC signal, and

the preset number of command retransfers was

exceeded (ECM).



was received after transmission of an EOR.Q signal,


exceeded (ECM).



was received after transmission of a RR signal, and

the preset number of command retransfers was

exceeded (ECM).



was received after transmission of a PS.NULL signal,


exceeded (ECM).



was received after transmission of a PPS.MPS


retransfers was exceeded (ECM).



was received after transmission of a PPS.EOM





was received after transmission of a PPS.EOP signal,


exceeded (ECM).



was received after transmission of a PPS.PRI-EOP




was interrupted by a signal error. T5 timeout was

detected during ECM Transmission (ECM).


was interrupted by a signal error. A DCN or other

inappropriate signal was received during standby for

DIS signal reception.


was interrupted by a signal error. A DCN signal was

received after transmission of a DNL (MPS or EOM)

signal (between units of our make).



received after transmission of a DCS, TCF signal.



received after transmission of an NSS1, NSS2 (TCF)

signal (between units of our make).



received after transmission of an NSS3, TCF signal

(between units of our make).



inappropriate signal was received after transmission

of an MPS signal.




of an EOM signal.




of an EOP signal.



received after transmission of a PRI-EOP signal.



received after transmission of a CNC signal

(between units of our make).



received after transmission of a CTC signal (ECM).



received after transmission of an EOR.Q signal

(ECM).



received after transmission of an RR signal (ECM).



received after transmission of a PPS.NULL signal

(ECM).



received after transmission of a PPS.MPS signal

(ECM).



received after transmission of a PPS.EOM signal

(ECM).



received after transmission of a PPS.EOP signal

(ECM).



received after transmission of a PPS.PRI-EOP signal

(ECM).


was interrupted by a signal error. Polarity reversal

was detected during handshake.



was detected during message transmission.


was interrupted by a signal error. A break in loop

current was detected during transmission.


was interrupted by a signal error. During reverse

polling in V.34 mode at the receiver unit, a CM

signal was not detected when transmitting after

reception.


was interrupted by a signal error. A PIP signal was

received after transmission of a PPS.NULL signal.


was interrupted by a signal error. During

transmission in V.34 mode, communication was

interrupted because a PPR signal was received over

(10) times even after reducing the communication

speed to the minimum with the symbol speed

maintained at the level of connection.


was interrupted by a signal error. During

transmission in V.34 mode, communication was

interrupted because of an impossible combination of

the symbol speed and communication speed.

E01100 or U01100 Fax Communication Error: Reception in G3 mode

was interrupted by a signal error. Function of the

unit differs from that indicated by a DCS signal.


was interrupted by a signal error. Function of the

unit (excl. communication mode select) differs from

that indicated by an NSS signal.


was interrupted by a signal error. A DTC (NSC)

signal was received when no transmission data was

in the unit.


was interrupted by a signal error. No response after

transmission of a DIS signal.



transmission of a DTC (NSC) signal.


was interrupted by a signal error. No training

reception after reception of a DCS or NSS signal.



transmission of an FTT signal.


was interrupted by a signal error. No message

reception after transmission of a CFR signal.



reception after transmission of an MCF signal.



reception after transmission of a PPR signal.



reception after transmission of a CTR signal.



reception after transmission of an ERR signal.


was interrupted by a signal error. No further signals

were received after reception of a message.



transmission of an MCF signal.



transmission of an RTP signal.



transmission of an RTN signal.



transmission of a PIP signal.



transmission of a PIN signal.



transmission of a CNS signal (between units of our

make).



transmission of a PPR signal (ECM).



transmission of an ERR signal (ECM).



transmission of an RNR signal (ECM).



transmission of an SPA signal (short protocol).



received after transmission of a DIS signal.



received after transmission of a DTC signal.



received after transmission of a DCS or NSS signal.



received after transmission of an FTT signal.



received after transmission of a CFR signal.



received after reception of a message.



received after transmission of an MCF signal

(interoffice communication after reception of an

MPS, EOM signal or confidential interoffice

communication).



received after transmission of an RTP signal.



received after transmission of an RTN signal.



received after transmission of a PIPsignal.



received after transmission of a PIN signal.



received after transmission of a PPR signal (ECM).



received after transmission of a CTR signal (ECM).



received after transmission of an ERR signal (ECM).



received after transmission of an PNP signal (ECM).



received after transmission of an SPA signal (short

protocol).


was interrupted by a signal error. During message

reception, transmission time exceeded the

maximum transmission time per line.


was interrupted by a signal error. Number of error

lines exceeded limits during message reception.


was interrupted by a signal error. A break in loop

current was detected during message reception.



was detected during message reception.


was interrupted by a signal error. One page length

exceeded the specified length during message

reception.


was interrupted by a signal error. A decoding error

occurred during MMR message reception.


was interrupted by a signal error. During reverse

polling in V.34 mode at the transmitting unit, a JM

signal was not detected after transmission of a CM

signal when receiving after transmission.


was interrupted by a signal error. Communication

was interrupted because an error occurred during

an image data reception sequence in the V.34

mode.


was interrupted by a signal error. A DIS signal with

different FIF was received after transmission of a

DIS signal.

E01400 or U01400 Fax Communication Error: An invalid one-touch key

was specified during communication.

E01500 or U01500 Fax Communication Error: A communication error

occurred when calling in V.8 mode.


occurred when called in V.8 mode.


occurred in phase 2 (line probing) in the period

after transmission of INFO0, before entering phase

3 (primary channel equivalent device training),

before starting T.30 protocol, during transmission in

V.34 mode. For example: INFO0/A/Abar (B/Bbar,

for polling transmission)/INFOh was not detected.


occurred in phase 4 (modem parameter exchange)

in the period after initiating the control channel,

before starting T.30 protocol, during transmission in

V.34 mode. For example: PPh/ALT/MPh/E was not

detected.


occurred before starting T.30 protocol during

transmission in V.34 mode. Operation was

interrupted due to the absence of a common

communication speed between the units. 1) A DCN

signal was received from the destination unit and

the line was cut, or 2) a DIS (NSF, CSI) signal was

received from the destination unit and in response

to the signal, the unit transmitted a DCN signal and

the line was cut.


occurred in phase 2 (line probing) in the period

after transmission of INFO0, before entering phase

3 (primary channel equivalent device training),

before starting T.30 protocol during reception in

V.34 mode. For example: INFO0/B/Bbar (A/Abar,

for polling reception)/probing tone was not

detected.


occurred in phase 3 (primary channel equivalent

device training), before starting T.30 protocol

during reception in V.34 mode. For example:

S/Sbar/PP/TRN was not detected.


occurred in phase 4 (modem parameter exchange)

in the period after initiating the control channel,

before starting T.30 protocol during reception in

V.34 mode. For example: PPh/ALT/MPh/E was not

detected.

E02000 or U02000 Fax Communication Error: Relay broadcast was

refused by a relay station because of a mismatch in

permit ID number and permit telephone number

when a relay command was used.

E02100 or U02100 Fax Communication Error: A relay command failed

because the destination unit (relay station) had no

relay broadcast capability.

E02200 or U02200 Fax Communication Error: A relay command from a

command station failed because a telephone

number was not registered in the relay station was

specified.


requested to a relay station but failed because a

telephone number was not registered in the relay

station was specified.

E02200 or U02200 Fax Communication Error: Subaddress-based relay

broadcast transmission failed because the data

registered in the subaddress relay box was deleted.

E02303 or U02303 Fax Communication Error: Receiving station

information was not normally received in reception

of a relay command. Timeout was detected before a

correct DNL signal was received.

E02304 or U02304 Fax Communication Error: Receiving station

information was not normally received in reception

of a relay command. A signal other than MPS or

EOM signal was received after a DNL signal was

received.

E02400 or U02400 Fax Communication Error: An interoffice

subaddress-based relay transmission was

interrupted because of a mismatch in the specified

relay box number.

E03000 or U03000 Fax Communication Error: No document was

present in the destination unit when polling

reception started.

E03100 or U03100 Fax Communication Error: In reverse polling,

although no original was set in the destination unit,

transmission was complete.

E03200 or U03200 Fax Communication Error: In confidential polling

reception, data was not accumulated in the

specified box in the destination unit.

E03200 or U03200 Fax Communication Error: In interoffice

subaddress-based bulletin board reception, data

was not stored in the box specified by the

destination unit.

E03300 or U03300 Fax Communication Error: In polling reception from

a unit of our make, operation was interrupted due

to a mismatch in permit ID number or telephone

number.


subaddress-based bulletin board reception,

operation was interrupted due to a mismatch in

permit ID number or telephone number.

E03400 or U03400 Fax Communication Error: Polling reception was

interupted because of a mismatch in individual

numbers.

E03500 or U03500 Fax Communication Error: In confidential polling

reception, the specified confidential box number

was not registered in the destination.


subaddress-based bulletin board reception, the

specified subaddress confidential box number was

not registered in the destination unit.

E03500 or U03500 Fax Communication Error: The destination was

being accessed.


reception was interrupted because of a mismatch in

specified confidential box numbers.

E03600 or U03600 Fax Communication Error: An interoffice

subaddress-based bulletin board reception was

interrupted because of a mismatch in the specified

subaddress confidential box number.


reception failed because the destination unit had no

confidential polling transmission capability or data

was not accumulated in any box in the destination

unit.

E03700 or U03700 Fax Communication Error: Interoffice subaddress-

based bulletin board reception failed because the

destination unit had no subaddress-based bulletin

board transmission capability, or data was not

stored in any subaddress confidental box in the

destination unit.

E04000 or U04000 Fax Communication Error: The confidential box

specified for confidential transmission was not

registered in the destination unit.


subaddress-based transmission mode, the specified

subaddress box number was not registered in the

destination unit.

E04000 or U04000 Fax Communication Error: The destination was

being accessed.

E04100 or U04100 Fax Communication Error: Confidential transmission

failed because the destination unit had no

confidential capability.


transmission failed because the destination unit had

no subaddress-based reception capability.

E04200 or U04200 Fax Communication Error: In encrypted

tranmission, the specified encryption box was not

registered in the destination unit.

E04300 or U04300 Fax Communication Error: Encrypted transmission

failed because the destination unit had no encrypted

communication capability.


interrupted because of an encryption key error

during encrypted transmission. Encryption keys did

not agree.


interrupted because of an encryption key error

during encrypted trasmission. The encryption key

was not registered.

E04500 or U04500 Fax Communication Error: Encrypted reception was

interrupted because of a mismatch in ecryption

keys.

E05000 or U05000 Fax Communication Error: In transmission with a

specified number, the set number of originals was

different from the number of transmitted originals.

E05100 or U05100 Fax Communication Error: Password check

transmission or restricted transmission was

interrupted because the permit ID numbers did not

match.


reception or restricted reception was interrupted

because the permit ID numbers did not match, the

rejected fax numbers did match, or the destination

receiver did not return its phone number.


reception or restricted reception was interrupted

because the permitted numbers did not match, the

rejected numbers did match, or the machine in

question did not acknowledge its phone number.

E09000 or U09000 Fax Communication Error: G3 communication was

attempted but failed because the destination unit

was a G2 machine.


requested from a command station but memory

overflowed during reception.

E12000 or U12000 Fax Communication Error: In subaddress-based

relay reception memory overflowed.

E12100 or U12100 Fax Communication Error: Relay was commanded

but memory overflowed in the destination unit

(relay station).

E14000 or U14000 Fax Communication Error: Memory overflowed

during confidential reception.

E14000 or U14000 Fax Communication Error: Memory overflowed in

subaddress-based confidential reception.


the destination unit during confidential

transmission.


the destination unit during interoffice subaddress-

based transmission.

E19000 or U19000 Fax Communication Error: Memory overflowed

during memory reception.


the destination unit during transmission.

E19200 or U19200 Fax Communication Error: Memory transmission

failed because a decoding error occurred.

E19300 or U19300 Fax Communication Error: Transmission failed

because an error occurred during JBIG encoding.

E19400 or U19400 Fax Communication Error: Reception failed because

an error occurred during JBIG encoding.

Send SMB Error

1102

Error: Username/Password or Shared Name/Folder

Name. Domain name is not entered.

Send SMB Error

1102


Name. Assign disable user/password.

Send SMB Error

1102


Name. Assign the user who is not allowed to access

the folder.

Send SMB Error

1102


Name. Assign disable shared name.

Send SMB Error

1102


Name. Host name error.

Send SMB Error

1103

Error: Pathname or File Name. Domain name is not

entered.

Send SMB Error

1103

Error: Pathname or File Name. Connect to the folder

which is not permitted for reference/writing.

Send SMB Error

1103

Error: Pathname or File Name. Assign disable folder

path.

Send SMB Error

1105

Error: Not Supported Protocol. SMB protocol is set

to OFF.

Send SMB Error

2101

Error: Can Not Connect. Enter the disable host

name/IP address.

Send SMB Error

2101

Error: Can Not Connect. Assign the wrong port

number.

Send SMB Error

2101

Error: Can Not Connect. Network is not connected.

Send SMB Error

2103

Error: Response Wait With Timeout. The server is

unable to communicate.

Send SMB Error

2201

Error: Network Transfer. Error occurs on the

network.

Send SMB Error

2203

Error: Response Wait With Timeout. Response is not

returned from the server, above specified time.

Send SMB Error

9181

Error: Page Max Count Over. The number of pages

of a send file exceeds 999 pages.

Send FTP Error

1101

Error: Host Name. Enter the disable host name/IP

address.

Send FTP Error

1102

Error: Username/Password. Domain name is not

entered.

Send FTP Error

1102

Error: Username/Password. Assign disable

user/password.

Send FTP Error

1103

Error: Pathname or File Name. Connect to the folder

which is not permitted for reference/writing.

Send FTP Error

1103

Error: Pathname or File Name. Assign disable folder

path.

Send FTP Error

1105

Error: Not Supported Protocol. FTP protocol is set to

OFF.

Send FTP Error

2101

Error: Can Not Connect. Enter the disable host

name/IP address.

Send FTP Error

2101

Error: Can Not Connect. Assign the wrong port

number.

Send FTP Error

2101


Send FTP Error

2102

Error: Cannot Connect With Timeout. The server is


Send FTP Error

2102

Error: Cannot Connect With Timeout. Send the

server which does not support FTP server.

Send FTP Error

2103



Send FTP Error

2201


network.

Send FTP Error

2202

Error: Network Transfer With Timeout. Error occurs

on the network.

Send FTP Error

2203



Send FTP Error

3101

Error: Server Response. The server is error status.

Send FTP Error

9181



Send email Error

1101

Error: Host Name. SMTP server name is not set.

Error SMTP server name.

Send email Error

1102

Error: Username/Password. User ID for the

authentication is not entered or entered wrongly.

Wrong authentication password is entered.

Send email Error

1104

Error: No Recipient Address. The destination

address is not specified.

Send email Error

1105

Error: Not Supported Protocol. SMTP protocol is set

to OFF.

Send email Error

1106

Error: No Sender Info. Sender address is not

entered.

Send email Error

2101

Error: Can Not Connect. Select [Other Authenticate]

when authenticating POP before SMTP.

Send email Error

2101

Error: Can Not Connect. The specified server is not

SMTP server.

Send email Error

2101


Send email Error

2102

Error: Cannot Connect With Timeout. The server is


Send email Error

2103



Send email Error

2201


network.

Send email Error

2202

Error: Network Transfer With Timeout. Error occurs

on the network.

Send email Error

2203



Send email Error

2204

Error: Email Size Limit. The size of the email

attachment exceeds its limit.

Send email Error

3101

Error: Server Response. The server is error status.

Send email Error

3101

Error: Server Response. Server setting is not

authenticated normally.

Send email Error

3201

Error: Not Found Authentication Mechanism.

Unsupported SMTP Authentication Mechanism is

found.

Send email Error

9181



TWAIN Error 2202 Error: Network Transfer With Timeout. Response is

not returned from the server, above the specified

time.

TWAIN Error 9181 Error: Page Max Count Over. The number of pages


Software Error

5101

Error: Not Yet Connected. Operation handle error.

Error for stored status in the operation handle.

Software Error

5102

Error: Already Connected. Operation handle error.

Error for stored status in the operation handle.

Software Error

5103

Error: Not Yet Opened. Error for storage status in

the operation handle.

Software Error

5104

Error: Already Opened. Error for storage status in

the operation handle.

Software Error

7101

Error: Memory Allocation. Insufficient memory

space.

Software Error

7102

Error: Socket Create. Unable to create a

communication socket.

Software Error 720f Error: Unknown Error. Unable to determine the

cause.

Send error. Job is

cancelled. Press

[End]. 1101

Send Email Error: Host Name. SMTP server name is

not set. Error SMTP server name.

Send error. Job is

cancelled. Press

[End]. 1101

Send FTP Error: Host Name. Enter the disable host

name/IP address.

Send error. Job is

cancelled. Press

[End]. 1102

Send Email Error: Username/Password. User ID for

the authentication is not entered or entered

wrongly. Wrong authentication password is entered.

Send error. Job is

cancelled. Press

[End]. 1102

Send SMB/FTP Error: Username/Password or

Shared Name/Folder Name. Domain name is not

entered.

Send error. Job is

cancelled. Press

[End]. 1102

Send SMB/FTP Error: Username/Password or

Shared Name/Folder Name. Assign disable

user/password.

Send error. Job is

cancelled. Press

[End]. 1102

Send SMB Error: Username/Password or Shared

Name/Folder Name. Assign disable shared name.

Send error. Job is

cancelled. Press

[End]. 1102

Send SMB Error: Username/Password or Shared

Name/Folder Name. Host name error.

Send error. Job is

cancelled. Press

[End]. 1103

Send SMB/FTP Error: Pathname or File Name.

Domain name is not entered.

Send error. Job is

cancelled. Press

[End]. 1103


Connect to the folder which is not permitted for

reference/writing.

Send error. Job is

cancelled. Press

[End]. 1103


Assign disable folder path.

Send error. Job is

cancelled. Press

[End]. 1104

Send Email Error: No Recipient Address. The

destination address is not specified.

Send error. Job is

cancelled. Press

[End]. 1105

Send Email Error: Not Supported Protocol. SMTP

protocol is set to OFF.

Send error. Job is

cancelled. Press

[End]. 1105

Send SMB Error: Not Supported Protocol. SMB


Send error. Job is

cancelled. Press

[End]. 1105

Send FTP Error: Not Supported Protocol. FTP


Send error. Job is

cancelled. Press

[End]. 1106

Send Email Error: No Sender Info. Sender address

is not entered.

Send error. Job is

cancelled. Press

[End]. 2101

Send Email Error: Can Not Connect. Network is not

connected.

Send error. Job is

cancelled. Press

[End]. 2101

Send Email Error: Can Not Connect. Select [Other

Authenticate] when authenticating POP before

SMTP.

Send error. Job is

cancelled. Press

[End]. 2101

Send Email Error: Can Not Connect. The specified

server is not SMTP server.

Send error. Job is

cancelled. Press

[End]. 2101

Send SMB/FTP Error: Can Not Connect. Enter the

disable host name/IP address.

Send error. Job is

cancelled. Press

[End]. 2101

Send SMB/FTP Error: Can Not Connect. Assign the

wrong port number.

Send error. Job is

cancelled. Press

[End]. 2101

Send SMB/FTP Error: Can Not Connect. Network is

not connected.

Send error. Job is

cancelled. Press

[End]. 2102

Send Email/ FTP Error: Cannot Connect With

Timeout. The server is unable to communicate.

Send error. Job is

cancelled. Press

[End]. 2102

Send FTP Error: Cannot Connect With Timeout.

Send the server which does not support FTP server.

Send error. Job is

cancelled. Press

[End]. 2103

Send Email/ SMB/ FTP Error: Response Wait With

Timeout. The server is unable to communicate.

Send error. Job is

cancelled. Press

[End]. 2201

Send Email/ SMB/ FTP Error: Network Transfer.

Error occurs on the network.

Send error. Job is

cancelled. Press

[End]. 2202

Send Email/FTP Error: Network Transfer With

Timeout. Error occurs on the network.

Send error. Job is

cancelled. Press

[End]. 2202

Send TWAIN Error: Network Transfer With Timeout.

Response is not returned from the server, above the

specified time.

Send error. Job is

cancelled. Press

[End]. 2203

Send Email/FTP Error: Response Wait With Timeout.

Response is not returned from the server, above

specified time.

Send error. Job is

cancelled. Press

[End]. 2204

Send Email Error: Email Size Limit. The size of the

email attachment exceeds its limit.

Send error. Job is

cancelled. Press

[End]. 3101

Send Email/FTP Error: Server Response. The server

is error status.

Send error. Job is

cancelled. Press

[End]. 3101

Send Email Error: Server Response. Server setting

is not authenticated normally.

Send error. Job is

cancelled. Press

[End]. 3201

Send Email Error: Not Found Authentication

Mechanism. Unsupported SMTP Authentication

Mechanism is found.

Send error. Job is

cancelled. Press

[End]. 5101

Send Software Error: Not Yet Connected. Operation

handle error. Error for stored status in the operation

handle.

Send error. Job is

cancelled. Press

[End]. 5102

Send Software Error: Already Connected. Operation

handle error. Error for stored status in the operation

handle.

Send error. Job is

cancelled. Press

[End]. 5103

Send SoftwareError: Not Yet Opened. Error for

storage status in the operation handle.

Send error. Job is

cancelled. Press

[End]. 5104

Send Software Error: Already Opened. Error for

storage status in the operation handle.

Send error. Job is

cancelled. Press

[End]. 7102

Send Software Error: Socket Create. Unable to

create a communication socket.

Send error. Job is

cancelled. Press

[End]. 720f

Send Software Error: Unknown Error. Unable to

determine the cause.

Send error. Job is

cancelled. Press

[End]. 9181

Send Email/ SMB/ FTP/ TWAIN Error: Page Max

Count Over. The number of pages of a send file

exceeds 999 pages.

"Acceptable staple

count exceeded."

Is the acceptable staple count exceeded?

"Add paper in

cassette #."

Is the indicated cassette out of paper?

"Add paper in MP

tray."

Is the paper of the specified size loaded in the

multipurpose tray?

"Add staples." Has the document finisher run out of staples?

"Add toner."

"An error has

occurred."

An internal error has occurred.Make a note of the

error code number displayed on the panel. See

above.

"Box Limit

Exceeded."

Document Box is full, and no further storage is

available; Job is cancelled. Repeat Copy Box is full,

and no further repeat copy is available.

"Cannot connect to

Authentication

Server."

"Cannot duplex

print on this

paper."

Did you select a paper size/type that cannot be

duplex printed?

"Cannot execute

this job."

Job is restricted by Job Accounting.

"Cannot offset this

paper."

Did you select a paper size that cannot be offset

(A3, B4, A5R, B6R, Folio, Ledger, Statement, &

8K)?

"Cannot punch this

paper type."


punched?

"Cannot staple this

paper."


stapled?

"Check the cover." Are any covers open? Does the message indicate

which cover is open?

"Check the

document

Is the document processor open? Is the top cover of

the document processor open?

processor."

"Check the

finisher."

Is the document finisher set correctly?"

"Clean the slit

glass."

Dirt has been identified on the slit glass.

"Empty the punch

waste box."

The punch waste box of the 3,000 sheet finisher is

full.

"Failed to specify

Job Accounting."

Job accounting is not specified in the print driver.

"Failed to store job

retention data."

"Fax box limit

exceeded."

Fax box is full, and no further storage is available.

"Finisher tray is full

of paper."

Is the acceptable storage capacity exceeded for the

document finisher tray?"

"Folding tray is full

of paper."

Is the acceptable storage capacity exceeded for the

folding tray of the 3,000 sheet document finisher?"

"Hard Disk error.

Job is cancelled.

Press [End] ##"

An error has occurred on the hard disk.

"Incorrect Login

User Name or

Password."

"Job Accounting

restriction

exceeded."

The print count exceeded the acceptable count

restricted by Job Accounting.

"Job Separator is

full of paper."

Is the maximum capacity of the job separator tray

exceeded?

"KPDL error." A PostScript error has occurred.

"Mailbox tray is full

of paper."

"Memory card

error."

Was the memory card (Compact Flash) removed

while being accessed? Was a valid memory card

inserted?

"Memory card

error. Job is

cancelled. Press

[End]. Code: 01

Memory Card Error: Format error.

"Memory card

error. Job is

cancelled. Press

[End]. Code: 04

Memory Card Error: Insufficient memory card space

to complete this operation.

"Memory is full." Unable to continue the job, as the memory is used

up."

"Memory Is Low" Logic Lockup

"Paper Jam. ###" Make a note of the jam location number displayed

on the panel. Leave the machine On.

"Print overrun." Warning. Low printer memory.

"Removable

memory error."

An error has occurred on the USB stick memory or

Compact Flash memory.

"Removable

memory was

removed."

"Replace all

originals and press

[Continue]."

"Replace the waste

toner box."

The waste toner box is full.

"Reset all originals

in the document

processor."

Are there any originals left in the document

processor?

"Scanner memory

is full."

Scanning cannot be performed due to insufficient

memory for the scanner. Is the acceptable scanning

count exceeded?

"Scanner Paused" DMA transmission of compressed, ecompressed,

rotated, relocated, or blanked-out image data does

not complete within a specified period of time.

"Set the folding

tray."

Is the folding tray correctly installed to the 3,000

sheet capacity document finisher?

"Set the folding

unit."

Is the folding tray correctly installed to the 3,000

sheet capacity document finisher?

"Set the punch

waste box."

The waste toner box is not installed correctly.

"Set the waste

toner box."

The waste toner box is not installed correctly.

"Staple error." The location of the jam will be indicated on the

panel. Leave the machine On.

"Staple jam." The location of the jam will be indicated on the

panel. Leave the machine On.

"The ID is not

registered."

The account ID# does not match.

"The memory card

is not formatted."

Is the removable memory formatted by this

machine?

"The phone

receiver is off the

hook."

"The removable

memory is not

formatted."

Is the removable memory formatted by this

machine?

"The source file is

not found."

The specified file is not found.

"Top tray of the

machine is full of

paper."

The exit tray at the top of the machine is full.

"Tray # is full of

paper."

Is the acceptable storage capacity exceeded for any

of the output trays A, B, or C of the 3,000 sheet

capacity document finisher?

"Warning low

memory."

Further scanning cannot be performed due to

insufficient memory.

Error Code Description

0xF330 Component: RIP. Category: RIP. Recovery impossible error

(CreatePrint and return back value of API is indirect).

0xF331 Component: RIP. Category: RIP. Fail to initialize.

0xF333 Component: RIP. Category: RIP. Access failure to ME.

0xF335 Component: RIP. Category: RIP. Failure to switch TASK.

0xF336 Component: RIP. Category: RIP. IOBL process failure.

0xFB30 Component: Panel. Category: KI-Panel. Failed to connect the

communication of the controller when starting up. Blue back

screen. Cannot enter maintenance mode.

0xFB31 Component: Panel. Category: KI-Panel. Refused to connect

the communication of the controller when starting up. Blue

back screen. Cannot enter maintenance mode.

0xFB32 Component: Panel. Category: KI-Panel. Time to start up

request command (start up request command could not be

received). Blue back screen. Cannot enter maintenance

mode.

0xFB33 Component: Panel. Category: KI-Panel. Cut off of the

communication with the controller is detected - waiting to

receive: select () OK return, recv() RX data length 0. Blue


0xFB34 Component: Panel. Category: KI-Panel. Time out for

Response telegraphic message (could not receive response

telegraphic message within a fixed time). In case on not

through httpd, this error occurs (in case it does not become

CGI time out).

0xFB35 Component: Panel. Category: KI-Panel. Received abusive

command from controller. At this moment, only the case that

unexpected command comes in when wating for the startup

request command.

0xFB36 Component: Panel. Category: KI-Panel. Connection error is

detected when waiting for he response telegraphic message

from the controller. select () function returned the error

(other than EINTR).

0xFB37 Component: Panel. Category: KI-Panel. Connection error is


from the controller. rcv () function returned the error.

0xFB38 Component: Panel. Category: KI-Panel. Communication error

is detected when transferring (using UNIX domain) response

telegraphic message in the panel. send() function returned

the error (other than EINTR).

0xFB39 Component: Panel. Category: KI-Panel. Crucial error is

detected when processing receive/transfer of the response

telegraphic message from controller. Failed to acquire

semafo???

0xFB3A Component: Panel. Category: KI-Panel. Communication error

is detected when sending required response telegraphic

message from panel. send() function returned the error

(other than EINTR).

CF000 Component: HDD. Failure to initialize with "dbinit,

hostif_stat_chg" comand.

CF000 Operation panel PWB comunication error.

CF010 ROM Checksum Error.

CF010 Main PWB Checksum Error/System Error. Communication

error between panel and main controller.

CF012 ROM Checksum Error.

CF020 Memory Checksum Error/Operation System Error.

CF030 Main PWB System Error.



CF041 Scanner PWB Communication Error.

CF050 Engine ROM Checksum Error.

CF060 Engine RAM Error.

CF070 Flash ROM Error. Defective flash ROM (which?).

CF080 Flash ROM Error (during download). Defective flash ROM

(which?).

CF090 Fax System M Communication Error.

CF125 Scanner Unit Error

CF131 Component: PCM. Category: OS. Failure to initialize with

"dbinit, hostif_stat_chg" comand.

CF131 Component: PCM. Category: OS. Failure to acquire Entity

data with "dbinit, hostif_stat_chg" comand.

CF145 Fax Unit Error.

CF14F Power Source Secondary Side Error/Operation System Error.

The operation decomes unstable after recovering the power

supply fail (brownout or power drop). Wall voltage is

unstable or the main power supply switch was turned

OFF/ON within 1 sec.

CF14F Component: OS. Category: OS. Primary supply voltage

dropped off temporarily and recovery operation was not

stable. If the input power supply voltage is not stable of the

Main SW is turned Off/On quickly (about 1 second), this

problem occurs.

CF186 Print Unit: DVU_PRT_SYSERR_F226_ERROR (Video data

flushing error)

CF18A Engine Firmware Incompatible.

CF18C Document BOX error.

CF1FF Component: ScanSys. Category: ScanSys. When the scanner

scanning parameter from the topside is in error.

CF1FF Component: IPLogical. Category: PrintSystem. Could not

obtain instance of Config, SystemStatus. Use below

mentioned class: ipl_search_output.cpp,

ipl_feeder_spec.cpp, outputcheck.cpp.

CF1FF Component: Machine Configuration. Category: PrintSystem.

Could not obtain instance of Config, SystemStatus. Use

below mentioned class: machine_status_engine.cpp.

CF1FF Component: OutputMission. Category: PrintSystem.

Increasing and decreasing "Lib", in case that even if there is

no original available, tried to process increasing &

decreasing.

CF1FF Component: OutputMission. Category: PrintSystem. In case

to specify some other value (indirect value) other than single

sided/duplex/forced duplex for increasing & decreasing "Lib".


of the address for Job setting value structure is NULL.


of the code for output completion notice is indirect.

CF1FF Component: OutputMission. Category: PrintSystem. When

writing the original information to the storage, in case to get

the reply back as [Other Error].


to get the reply as [Finisher out of order Error], [No Feeder

available in search] from Paper feed/eject "Lib".


to get the reply as failure from rotation calculation "Lib".

CF1FF Component: PrintSystem. Category: PrintSystem. Could not

obtain instance of Config, SystemStatus. Use below

mentioned class: print_startup.cpp.

CF1FF Component: SVI. Category: LioPanel. Logical Error (In case

of given parameter is NULL).

CF214 Codec: GICL_CDC_ERR_FACTOR_JPEG (several hardware

error, software error).

CF215 Codec: GICL_CDC_ERR_FACTOR_SRLE (several hardware

error, software error).

CF234 Data conversion error.

CF235 Error code when receiving/printing email.

CF245 Process Manager:

SYS_PRCM_ERR_FACTOR_SVC_PROC_DOWN (Device

process down).


SYS_PRCM_ERR_FACTOR_DEV_PROC_DOWN (Device

process down).


SYS_PRCM_ERR_FACTOR_JOBIMG_PROC_DOWN (Job image

process down).

CF247 Component: ScanSys. Category: ScanSys. Library Error

inside of ScanSys.

CF248 Component: UNKNOWN. Category: UNKNOWN.

CF248 Component: UNKNOWN. Category: UNKNOWN. Code present

on with Kyocera Barfode Font CF card installed.


SYS_PRCM_ERR_FACTOR_PRN_PROC_DOWN (Printer

process down).

CF256 Fax System M IOBL error or KUIOLIB error. Poor contact at

the fax card card due to mis-installation.

CF257 Component: LFM. Category: FaxSys. KUIOLIB error. Poor


CF257 Fax System M IOBL error or KUIOLIB error. Poor contact at

the fax card card due to mis-installation.

CF25E Network Manager:

CF25F Component: LFM. Category: FaxSys. Instance Check Error,

Paramemter Error from topside.

CF26F Component: PrintSys. Category: PrintSys. It occurs when the

error noticed from VideoDriver. Use by Video_Driver class:

Function name, factor can be found by the detail code.

CF26F Print System Other Errors. Bug of v.2.03B has been fixed by

v. 2.04A (Booklet > Booklet Print).

CF26F System State Manager:

CF278 Energy Saving Manager:

CF320 Component: LioFax. Category: FaxSys. An Observer Deletion

Error occurred during salvage process. Error received from

the method on EventManager or message Tx.

CF321 Component: LioFax. Category: FaxSys. Segment code for

LioFax initialization is different from "03KH".

CF323 Component: LioFax. Category: FaxSys. Return address of

Page class when doing FAX Tx/Rx is other abnormal error.

Entity (Config, BOX, etc.) access error.

CF324 Component: LioFax. Category: FaxSys. Entity parameter

error.

CF325 Component: LioFax. Category: FaxSys. In case that the time

when Error came back from LFM.

CF326 Component: LioFax. Category: FaxSys. IOBL error.

CF327 Component: LioFax. Category: FaxSys. At the time of

KUIOLIB error, CodeChange error, FaxLib error (Sender

recorde, Entity related error).

CF32F Component: LioFax. Category: FaxSys. Instance Check Error.

Parameter Error from topside.

CF337 Device Error (scan control):

CF3FF Component: RIP. Category: RIP. Other/System Crucial Error.

CF423 Component: FaxJOB. Category: FaxSys. As the error came

back at IF for DocumentBox, JobInfo, Config Entity.

CF423 Component: FaxJob. Category: FaxSys. The error came back

when accessing (obtaining data, setting data) to below Entity

related: job_ent(JobModel,JobInfo), config_ent, reservation,

account(certificate), document_box.

CF423 Fax System M Error. Wrong data or value detected when the

following function is used. Or poor contact at fax card due to

mis-installation.

CF423 Fax System M Error. The IF error detects during system

authentication from ACT_Account_Manager. Or poor contact

at fax card due to mis-installation.

CF424 Component: FaxJob. Category: FaxSys. As the error came

back when obtaining IF for system authentication from

ACT_Account_Manager.

CF424 Component: FaxJob. Category: FaxSys. The date obtained

from the below Entity related is unexpected data:

job_ent(JobInfo).

CF427 Component: FaxJob. Category: FaxSys. The error came back

for the IF of LioFax observer addition/deletion.

CF42F Component: FaxJob. Category: FaxSys. As handing over of

the NULL pointer in the class occurred. As memory

reservation with new in heap domain is failed: Assert for

preventing from segment drop off.

CF42F Component: FaxJob. Category: FaxSys. When generating the

class, fail new at obtaining data domain, soft logic error

(software bug).

CF433 Component: NetClient. Category: ImageProcess. Entity

Error.

CF434 Component: NetClient. Category: ImageProcess. Entity Data

Invalid.

CF437 Component: NetClient. Category: ImageProcess. Other

Library Error (ImageLibrary, PageData, EventManager).

CF43F Component: NetClient. Category: ImageProcess. Crucial (no

memory, invalid parameter, etc.).

CF441 Component: CreateScan. Category: ImageProcess. Initialize

Error.

CF444 Component: CreateScan. Category: ImageProcess. Entity

Data Invalid.

CF445 Component: CreateScan. Category: ImageProcess.

Middleware Error (LioScanner error).

CF451 Component: CreatePrint. Category: ImageProcess.

Initialization Error.

CF433

CF434

CF437

CF43F

CF441

CF444

CF445

HDD Image Process Error. Destruction of stored jobs on the

HDD. It may occur when selecting the keys for calling stored

copy or scanner job from a custom box.

CF451

CF453 Component: CreatePrint. Category: ImageProcess. Entity

Error.

CF454 Component: CreatePrint. Category: ImageProcess. Entity

Data Mismatch.

CF45F Component: CreatePrint. Category: ImageProcess. Other

Error.

CF460 Component: CreateBox (Memory Tx). Category:

ImageProcess. Unrecoverable Error.

CF463 Component: CreateBox (Memory Tx). Category:

ImageProcess. Entity Error.

CF46F Component: CreateBox (Memory Tx). Category:

ImageProcess. Crucial (no memory, invalid parameter, etc.).

CF46F PDL Interpreter: REN_INT_ERR_FACTOR_GENERAL (other

general error).

CF470 Component: CreateFax. Category: ImageProcess.

Unrecoverable Error.

CF473 Component: CreateFax. Category: ImageProcess. Entity

Error.

CF47F Component: CreateFax. Category: ImageProcess. Crucial (no

memory, invalid parameter, etc.).

CF484 Component: Edit. Category: ImageProcess. Data Invalid

(PageData).

CF487 Component: Edit. Category: ImageProcess. Other Library

Error (ImageLibrary).

CF48F Component: Edit. Category: ImageProcess. Crucial.

CF490 Component: Output(Fax). Category: ImageProcess.

Unrecoverable Error.

CF493 Component: Output(Fax). Category: ImageProcess. Entity

Error.

CF494 Component: Output(Fax). Category: ImageProcess. Entity

Data Invalid.

CF45F

CF453

CF454

CF45F

CF460

CF463

CF46F

CF470

CF473

CF47F

CF484

CF487

CF48F

CF490

CF493

CF494

HDD Image Process Error. Destruction of stored jobs on the

HDD. It may occur when selecting the keys for calling stored

copy or scanner job from a custom box.

CF515

CF526 System Error:

CF528 Component: SVI. Category: LioPanel. Panel data abusion

error.

CF530 Component: PJL. Category: RIP. Recovery impossible error:

Thread Create failed.

CF530 Component: ReportEventService. Category: RIP. Recovery

impossible error: Thread Create failed.

CF530 Component: SVCTL_FaxRx_Event_Control. Category: KI Sc.

As failed to obtain EM_FaxRx_Ec_Event_Fax_Enable.

CF530 Component: SVCTL_Reservation_Event_Control. Category:

KI Sc. As failed to notice the event for

EM_Rsv_EC_op_Event_FaxJob_Ready.

CF530 Component: SVCTL_Job_Start_Command. As JobInfo giving

to JSM_JobServiceManager is NULL.

CF533 Component: PJL. Category: RIP. Entity error: when CLITICAL

ERROR occurred at ME access.

CF533 Component: ReportEventService. Category: RIP. Entity

error: when CLITICAL ERROR occurred at ME access.

CF551 Component: MLPRN. Category: NetAppl. Task generation

error.

CF551 Component: MLPRT. Category: NetAppl. Task generation

error.

CF551 Component: EVR_LGS. Category: NetAppl. Task generation

error.

CF610 Component: SSTUP. Category: OS. Error in the

SystemStartUp (Thread generation, Entity data acquisition,

DiskManager operation).

CF610 Undefined.

CF610 System Start Error.

CF615 Report Page Generator: USV_RPG_ERR_FACTOR_STREAM

(Stream access error).

CF620 Component: EventManager. Category: KM-Entity. Failed to

obtain/receive event from framework.

CF620 Unable to Print.

CF620 System Error. Error acquiring the event data. Panel detects

CF000 as same error.

CF620 System Error. Error acquiring the event data. Panel detects

CF000 as same error. Unable to Load Files To CF Card.

CF630 Component: PowerManagement. Category: OS. Failed to

mount or unmount during transition of the condition.

CF710 Component: IIS. Category: NetApl. Network file written error

(inetd).

CF713 Component: IIS. Category: NetApl. Entity error (inetd).


(services).

CF723 Component: IIS. Category: NetApl. Entity error (services).


(snmpd).

CF733 Component: IIS. Category: NetApl. Entity error (snmpd).

CF743 Component: IIS. Category: NetApl. Entity error (hosts

allow).


(hostname).

CF753 Component: IIS. Category: NetApl. Entity error (hostname).


(papd).

CF763 Component: IIS. Category: NetApl. Entity error (papd).


(cups).

CF773 Component: IIS. Category: NetApl. Entity error (cups).


(dhcclient).

CF783 Component: IIS. Category: NetApl. Entity error (dhcclient).


(smb).

CF793 Component: IIS. Category: NetApl. Entity error (smb).

CF7A0 Component: IIS. Category: NetApl. Network file written error

(netware).

CF7A3 Component: IIS. Category: NetApl. Entity error (netware).

CF7B0 Component: IIS. Category: NetApl. Network file written error

(ipfilter).

CF7B3 Component: IIS. Category: NetApl. Entity error (ipfilter).

CF7C0 Component: IIS. Category: NetApl. Network file written error

(ethermode).

CF7C3 Component: IIS. Category: NetApl. Entity error (ethermode).

CF7D0 Component: IIS. Category: NetApl. Network file written error

(other).

CF7D3 Component: IIS. Category: NetApl. Entity error (other).

CF7D7 Readout Error of SSL (authentication data).

CFAxx HDD Error.

CFAxx HDD Error.

CFA10 Component: OS_TOOLS. Category: OS. Error inside of hot

plug detection thread, overwritten thread (failed to issue the

event, failed to operate signal handler).

CFA20 Component: OS_TOOLS. Category: OS. Failed to obtain

memory size.

CFA23 Component: OS_TOOLS. Category: OS. Access error to the

Entity at master data stored area component.

CFA30 Component: OS_TOOLS. Category: OS. CF-DETECT OPEN

error <0x07>.

CFA30 Component: OS_TOOLS. Category: OS. CF-DETECT IOCTL

error <0x08>.

CFA30 Component: OS_TOOLS. Category: OS. CF-DETECT CLOSE

error <0x09>.

CFA30 Component: OS_TOOLS. Category: OS. AES conversion

OPEN error <0x0a>.


IOCTL error <0x0b>.


CLOSE error <0x0c>.


command return value error <0x0d>.

CFA30 Component: OS_TOOLS. Category: OS. Message queue

creation error <0x15>.

CFA30 Component: OS_TOOLS. Category: OS. Message queue Tx

error <0x16>.

CFA30 Component: OS_TOOLS. Category: OS. Message queue Rx

error <0x17>.

CFA30 Component: OS_TOOLS. Category: OS. Message queue

deletion error <0x18>.

CFA37 Component: OS_TOOLS. Category: OS. Event Tx error

<0x19>.

CFA43 Component: OS_TOOLS. Category: OS. Access error to the

Entity at USB activation component.

CFB00 Component: Panel. Category: KI-Panel. Netfront error

(SLIM_E_GENERIC).


(SLIM_HTTP_E_DNS_INVAL).


(SLIM_HTTP_E_DNS_NOSERVER).


(SLIM_HTTP_E_DNS_TIMEDOUT).


(SLIM_HTTP_E_DNS_NOTFOUND).


(SLIM_HTTP_E_TCP_OPEN).


(SLIM_HTTP_E_TCP_CONNECT).


(SLIM_HTTP_E_TCP_READ).


(SLIM_HTTP_E_TCP_WRITE).


(SLIM_HTTP_E_SSL_CONNECT).

CFB0A Component: Panel. Category: KI-Panel. Netfront error

(SLIM_HTTP_E_SSL_HANDSHAKE).

CFB0B Component: Panel. Category: KI-Panel. Netfront error

(SLIM_HTTP_E_SSL_READ).

CFB0C Component: Panel. Category: KI-Panel. Netfront error

(SLIM_HTTP_E_SSL_WRITE).

CFB0D Component: Panel. Category: KI-Panel. Netfront error

(SLIM_HTTP_E_REQTIMEDOUT).

CFB0E Component: Panel. Category: KI-Panel. Netfront error

(SLIM_HTTP_E_RSPTIMEDOUT).

CFB0F Component: Panel. Category: KI-Panel. Netfront error

(SLIM_HTTP_E_CACHE_NONE).


(SLIM_HTTP_E_CACHE_EXPIRE).


(SLIM_HTTP_E_AUTH_UNKNOWN).


(SLIM_HTTP_E_AUTH_NOHEADER).


(SLIM_HTTP_E_AUTH_FORMAT).


(SLIM_HTTP_E_REDIRECT_FORMAT).


(SLIM_HTTP_E_REDIRECT_CANCELLED).


(SLIM_HTTP_E_REQ_HEADER_SIZEOVER).


(SLIM_HTTP_E_REQ_BODY_SIZEOVER).


(SLIM_HTTP_E_RSP_HEADER_SIZEOVER).


(SLIM_HTTP_E_REQ_TOOMANYCONTINUE).


(SLIM_HTTP_E_TLS_INTOLERANT).


(SLIM_FILEP_E_OPEN).


(SLIM_FILEP_E_READ).

CFB1D Component: Panel. Category: KI-Panel. Netfront error

(SLIM_CONTENT_E_SIZEOVER).

CFB1E Component: Panel. Category: KI-Panel. Netfront error

(SLIM_CONTENT_E_NO_CONTENT).

CFB1F Component: Panel. Category: KI-Panel. Netfront error

(SLIM_CONTENT_E_TOOMANYREDIRECT).


(SLIM_CONTENT_E_TOOMANYAUTH).


(SLIM_BROWSER_ERROR_NOMEMORY).


(SLIM_BROWSER_ERROR_NOMEMORY_IMAGE).


(SLIM_BROWSER_ERROR_TOTAL_SIZEOVER).


(SLIM_BROWSER_ERROR_BADURL).


(SLIM_BROWSER_ERROR_BADMIMETYPE).


(SLIM_BROWSER_ERROR_MIXEDSECURETYPE).


(SLIM_BROWSER_ERROR_INPUTHISTORY_SIZEOVER).


(SLIM_BROWSER_ERROR_INPUT_REQUIRED).


(SLIM_BROWSER_ERROR_KMC_NOTIFYMAXWINDOW).


(SLIM_BROWSER_ERROR_KMC_SWKOVERFLOW).


(SLIM_BROWSER_ERROR_KMC_FILEDOWNLOAD).


(SLIM_BROWSER_ERROR_KMC_SEGFAULT).

CFB2C

CFB30

CFB31

Panel Error. NetFont error. Communication error between

panel and main controller during initialization or rejection of

communication by controller during initialization. Blue Screen

of Death.

CFB30 Component: Panel. Category: KI-Panel. Failed to connect the

communication of the controller when starting up. Blue back

screen. Cannot enter maintenance mode.



CFB31 Component: Panel. Category: KI-Panel. Refused to connect

the communication of the controller when starting up. Blue




CFB32 Component: Panel. Category: KI-Panel. Time to start up

request command (start up request command could not be

received). Blue back screen. Cannot enter maintenance

mode.

CFB32 Panel Error. Timeout request for start up command. Start

command hasn't been received. Possible destruction of

system file in HDD. Cannot enter maintenance mode. Blue

Screen of Death.

CFB33 Component: Panel. Category: KI-Panel. Cut off of the

communication with the controller is detected - waiting to

receive: select () OK return, recv() RX data length 0. Blue


CFB33 Panel Error. Detects disconnection with controller. Possible

overdrive of control board or destruction of system file in

HDD. Cannot enter maintenance mode. Blue Screen of

Death.

CFB34 Component: Panel. Category: KI-Panel. Time out for

Response telegraphic message (could not receive response

telegraphic message within a fixed time). In case on not

through httpd, this error occurs (in case it does not become

CGI time out).

CFB35 Component: Panel. Category: KI-Panel. Received abusive

command from controller. At this moment, only the case that

unexpected command comes in when wating for the startup

request command.

CFB36 Component: Panel. Category: KI-Panel. Connection error is


from the controller. select () function returned the error

(other than EINTR).

CFB37 Component: Panel. Category: KI-Panel. Connection error is


from the controller. rcv () function returned the error.

CFB38 Component: Panel. Category: KI-Panel. Communication error

is detected when transferring (using UNIX domain) response

telegraphic message in the panel. send() function returned

the error (other than EINTR).

CFB39 Component: Panel. Category: KI-Panel. Crucial error is

detected when processing receive/transfer of the response

telegraphic message from controller. Failed to acquire

semafo???

CFB3A Component: Panel. Category: KI-Panel. Communication error

is detected when sending required response telegraphic

message from panel. send() function returned the error

(other than EINTR).

Documents

Canon Errors 2