Upload
nguyendiep
View
216
Download
2
Embed Size (px)
Citation preview
IINNSSTTAALLLLAATT IIOONN IINNSSTTRRUUCCTT IIOONNSS
QUESTIONS OR CONCERNS CONTACT CANARM AT:1-800-265-1833 (English)1-800-567-2513 (French)
Monday through Friday 8:00 a.m. to 5:00 p.m. E.S.T.
LIGHTING & FANS
ECLAIRAGES & VENTILATEURS
NOTE: FOR OPTIMUM QUIETNESS, FULLY ASSEMBLE FAN AND RUN 24 HOURS
CANARM LTD.2157 Parkedale Ave.,
Brockville, OntarioK6V 5V6
PH: (613) 342-5424FX: (613) 342-8437
CANARM LTEE.8500 Rue Grenache,
Anjou, QuebecH1J 2B1
PH: (514) 353-2255FX: (514) 353-2522
HUGGER STYLE
CF-206/13
!“INSTRUCTIONS PERTAINING TO RISK OF FIRE OR INJURY TO PERSONS”
INSTALLATION AND WIRING TO BE IN ACCORDANCE WITH CEC,NEC, LOCAL ELECTRICAL CODES and ANSI/NFPA 70.
Consult a qualified electrician if you are not familiar with wiring.
“READ ALL INSTRUCTIONS”
“IMPORTANT SAFETY INSTRUCTIONS”
“SAVE THESE INSTRUCTIONS”
TOOLS AND MATERIALS REQUIRED- Philips Screw Driver- Blade Screw Driver
- Step Ladder- Wire Cutters
- Wiring supplies as required by electrical code.
CANARM 5 YEAR LIMITED WARRANTY“THANK YOU” for purchasing a Canarm product. It is our policy to furnish you with
high quality products at a fair price. With proper installation your fan should provide you withyears of money saving comfort.
This fan is guaranteed to be free from defects in workmanship and material for aperiod of five (5) years from date of purchase. Within the first (1) year from date of purchase any defective product should be returned to your RETAIL OUTLET along with proofof purchase. For the balance of the warranty, four (4) years, the MOTOR WINDINGS ONLY
,
shall be free of defects. We will correct such defects or replace the motor assembly at ouroption if the product is returned, FREIGHT PREPAID, to Canarm. The returned fan must beaccompanied by your proof of purchase and a cheque for $20.00 for handling andlabour charges.
All costs of removing and re-installing the product are YOUR RESPONSIBILITY
.
Damage to any part as such by accident, misuse, improper installation or by affixing any accessories IS NOT covered by this warranty. As a result of varying climatic conditions in ourarea this warranty does not cover any changes in finishes, including rusting, pitting, corroding,tarnishing or peeling.WARRANTY VOID: In cases of alteration, abuse, installation not in accordance with
instructions or REMOVAL of the C.S.A. Sticker.
Pg. #2 Pg. #11
INSTRUCTIONSA ceiling fan has a completely internal switching system for total operation by
way of pull chains.On a fan/light combination, pull chains will exist: One for light,on and off. The second is for fan speeds. This will be marked (SPEED) on the fanswitch housing.
1st Pull will give fan High Speed2nd Pull will give fan Medium Speed3rd Pull will give fan Low Speed4th Pull will Shut Fan Off
The third pull chain is for Forward/Reverse#(Note: Some models come with a slideswitch instead of a pull chain). This setting would usually be changed twice peryear. Downdraft in summer to create a wind chill to give a cooling effect. Updraftin winter to circulate the hot stratified air off the ceiling and back down to the floorwithout creating a wind chill.
TROUBLESHOOTINGTROUBLE SUGGESTIONS
- Check fuses and circuit breakers.1. Fan will not start - Check wiring connections to fan.
- Check wiring connections in switch housing.CAUTION: Turn power off for last two items.
2. Fan sounds noisy - Check to make sure that all screws in motor housing are snug.- Check to make sure that blade bracket screws are tight.- Check to make sure that marrettes in switch housing
are not rattling against wall of switch housing.- If fan has a light kit make sure switch housing
screws and set screws are tight.- Some fan motors are sensitive to signals from solid
state variable controls. If solid state controller isused, change to an alternative control. (See a Canarm representative for a list of available controls.)
- Allow a 24 hour break in period to eliminate most noises.
3. Fan wobbles - Check that all blades are screwed firmly into blade brackets.or shakesexcessively.
- Check that blade brackets are secured firmly to motor.- Check distance from tip of blades to ceiling. Gently bend up or
down the blade brackets until all distances are the same.- Check distance between blade tip to blade tip. All
measurements should be equal. Loosen blade screws and position blade until even then re-tighten.
- Check that the downrod hemisphere notch is engaged in canopy. - Check to make sure that jam screws in downrod are tightened.- Make sure canopy and mounting bracket are
tightened securely to wooden joist.- Make sure warpage has not occurred in wooden
blades. If so, contact the Canarm customer service department for replacement parts.
SAFETY PRECAUTIONS1. Turn off power at main electrical service box before starting installation.2. Electrical connections must comply with local code ordinances, national
electrical codes, CEC, NEC and ANSI/NFPA 70.3. Make sure the installation site you choose allows the fan blades to rotate
freely without any obstructions.4. When mounting the fan on a ceiling outlet box, Use an approved (CSA for Canada and UL for U.S.) ceiling fan box marked "FOR FAN SUPPORT".
5. WARNING: To reduce the risk of fire, electric shock, or personal injury, mount fan only to an outlet box marked acceptable for fan support and use mounting screws provided with the outlet box. Most outlet boxes commonly used for the support of lighting fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if in doubt.
Ensure the outlet box is securely installed in place such that it is able tosupport at least the fan weight.
three
6.Total Fan Weight For Reference: 30"approximate 5.0 kgs(11.02lbs),36"approximate 6.0 kgs(13.23lbs), 42"approximate 7.5 kgs(16.53lbs),48"approximate 8.0 kgs(17.63lbs), 52"approximate 9.0 kgs(19.84lbs).
WARNING- To reduce the risk of fire or electrical shock DO NOT use this fan with any solid state speed control device.
- To reduce the risk of personal injury DO NOT bend the blade brackets when installing the brackets, balancing the blades or cleaning the fan. Also, DO NOT insert foreign objects in between rotating fan blades.
- Mount with the lowest moving parts at least 2.15 Meters (7 Feet) above floor or grade level.
- DO NOT operate reversing switch while fan blades are in motion. Fan must be turned off and rotating blades stopped, reverse chain pulled, the speed chain pulled again to start in the opposite direction.
1. Wooden Joist2. Ceiling3. Approved (CSA for Canada and UL for U.S.) ceiling fan box (not provided)4. J-Hook5. Blade Bracket (Cast Metal)6. Mounting Bracket7. Outlet Box Screws (not provided)8. Motor9. Lock Washer
10. Mounting Bracket Screws11. Mounting Bracket Side Screws12. Lock Washer13. Decorative Motor Housing14. Hex Nut15. Steel Flat Washer16. Flat Fibre Washer17. Fibre Bracket Gasket18. Blade19. Blade Bracket (Stamped Metal)20. Blade Bracket Screws21. Motor Screws22. Lock Washer
Pg. #10 Pg. #3
ASSEMBLY DRAWING
1
764
3
2
10
9
8
11
1615221413
12
1818
5 19
20
17
21
22
161520
Cast BladeBrackets
Stamped BladeBrackets
Style #1
Style #2
LIGHT KITS (Optional in some fans)
DETACHABLE LIGHT KITS (Continued)- Place shades on light kit and secure with either screws, finger tight, or
push and turn for pop-off style shades.- Install proper wattage and type of bulb identified on light kit or shade.
or
PERMANENTLY ATTACHED LIGHT - Loosen thumb screws on light.- Install proper wattage and type of bulb identified on light or shade.- Place shade on light and secure with thumb screws, finger tight.
ShadeThumbScrew
Light Kit
Light Kit
ShadePush and
Turn
7.
A
B
Fig. C
Fig. A
Fig. 9b
Glass
Fixture Socket
Spinner Nut
Tool
NOTE:Electrical diagrams are for reference only. Light kits that are not packed with the fan must be CSA/UL Listed and marked suitable for use withthe model fan you are installing. Switches must be CSA/UL General Use Switches. Refer to the instructions packaged with the light kits and switches for proper assembly.
WARNING: Check all connections, set screws and screws are securely tightened before the next step. Fig. 1
Fig. 9a
Fig. 9c
Fig. 9d
Pg. #4 Pg.
#9
1.
2.
6.
7.
A
INSTINSTALLAALLATIONTION
INSTALL MOUNTING BRACKET
- Install J-Hook through centre of outlet box and into the wooden joist.- Mount “mounting bracket” to outlet box using outlet box screws.
ELECTRICAL HOOK UP- There are several different wiring combinations that can be used in
controlling your ceiling fan to meet your specific requirements. Should the following method not meet your requirements call or visit your nearest Canarm distributor for a full list of fan accessories.
CAUTION
Green Wire - GROUNDBlack Wire (Fan) - POWERWhite Wire (Fan) - COMMONRed or Blue Wire (Light Kit) - POWER
SEE SAFETY PRECAUTIONS ONPG. #2 BEFORE WIRING
J-Hook
MountingBracket
OutletBox
Wood Joist
Ceiling
J-Hook
MountingBracket
Outlet Box
Wood Joist
Ceiling
Style #1 Style #2
MOUNTING BLADE BRACKETSAND BLADES TO MOTOR- Remove motor screws and lock
washers from motor.- Insert a motor screw and lock
washer into blade bracket.- Turn motor until hole spacing on
motor corresponds with the holes in the blade bracket.
- Place fibre bracket gasket over screw.
- Screw the motor screw into the motor (two turns). Repeat procedure for second screw.
- Tighten both screws down with screw driver.
Motor Screw
Lock Washer
Fibre Bracket Gasket
LIGHT KITS (Optional in some fans)
DETACHABLE LIGHT KITS- Remove light kit screws and
washers.- Connect polarized connectors of
light kit to corresponding connectors found in switch housing.
WARNING: BE SURE TO TURN OFF POWERBEFORE INSTALLING
- Carefully tuck electrical wires back into switch housing, align light kit with switch housing and secure with three light kit screws and washers.
Motor
Red or BlueWires
Light KitScrews
Light Kit
SwitchHousing
White Wires
Lockwasher
NOTE: All set screws must be checked and retightened where necessary, before and after installation.
WARNING: To Reduce The Risk Of Fire, Electric Shock, Or Personal Injury, Mount To UL/CSA Listed Outlet Box Marked Acceptable for Fan Support And Use Mounting Screws Provided With The Outlet Box.
Black or Blue Wires
Fig. 2a Fig. 2b
Fig. 7
Fig. 8
Outlet box Screws(not provided)
Outlet box Screws(not provided)
Pg. #8
ELECTRICAL HOOK UP (Continued)
- Hang fan on mounting bracket by holding motor so that inside of motor is pointing down, insert “T” slot style end of motor bracket into rectangular cut out in mounting bracket. NOTE: Remove screw and lock washer from “T” slot end of motor bracket before hanging.
- Hang motor from mounting bracket using temporary hanging hook.
CONNECTING THE (GREEN) GROUND WIRE
- Connect ground wire from outlet box to green wire on the motor using a (not supplied).
TemporaryHanging Hook
Motor
Green Ground Wire
Style #1 Style #2
Mounting Bracket
“T” Slot Style End ofMotor Bracket
Pg. #5
MOUNT BLADE BRACKETS TO BLADES
Hex Nut
Blade Bracket
Blade Bracket Screw
Fibre Washer
Flat WasherBlade BracketScrew
Blade Bracket
Fibre Washer
Flat Washer
Cast Blade Brackets
- Place blade bracket screw through flat
washer, fibre washer and blade.- Align with corresponding hole in
blade bracket.- Repeat with (2) remaining screws
and tighten.
Stamped Blade Brackets
- Place blade bracket screw through hole
in blade bracket.- Align with corresponding hole in blade bracket.- Place fibre washer and flat washer over blade
bracket screw and secure with hex nut.- Repeat with (2) remaining screws and tighten.
INSTALL DECORATIVE MOTOR HOUSING- Remove 4 screws and washers from sides of mounting bracket.- Position decorative motor housing so that the holes in housing align with
holes in mounting bracket.- Tighten decorative motor housing using the 4 screws and washers
previously removed.
Screws
DecorativeMotor Housing
Washers
2.4.
5.A
Hex Nut
Blade Bracket
Blade Bracket Screw
Fibre Washer
Flat WasherLock Washer
Fig. 5
Fig. 6a Fig. 6b
Fig. 3a Fig. 3b
Fig. 3c
Marette
marette.
- Take out hardware package. - Take out hardware package.
Screws andLock Washers
Style #2
MOUNT MOTOR TO MOUNTING BRACKET- Place the looped end of the safety cable over the J-Hook.- Remove the four bottom screws and washers from the mounting bracket.- Remove the temporary hanging hook.- Align motor with mounting bracket and slide in place until the four holes
line up.- Tighten motor to mounting bracket using the four screws and washers
previously removed.- Neatly tuck all electrical wires into outlet box.
Pg. #7
3.
Pg. #6
ELECTRICAL HOOK UP (Continued)
CONNECTING BLACK,
WHITE,
AND
(RED OR
BLUE)
WIRES
-
Connect
white
wire
from
outlet
box
to
whitewire
from
fan
using
(not supplied).
-
Connect
black
wire
from
outlet
box
to
blackwire
from
fan
plus
(red
or
blue
wire)
usinga
NOTE: A red
or
blue
wire
would
feed
power to
a
light
kit
if
applicable.
Red
or
Blue
Wires
White
Wires
Black
Wire
Ground
Wire
NOTE: Once
ground
wires
are
connected,
carefully
tuckwires
and
marrettes
into
supply
box.
2.
B
Screw
Safety Cable
Lockwasher
Style #1
Fig. 3d
Fig. 4a Fig. 4b
-
-
After making the wire connections, ensure the wires should be spreadapart with the grounded conductor and the equipment-groundingconductor on one side of the outlet box and the ungrounded conductoron the other side of the outlet box.Ensure the splices after being made should be turned upward andpushed carefully up into the outlet box.
marette.
marettes