Upload
lamtu
View
218
Download
0
Embed Size (px)
Citation preview
CALICUT UNIVERSITY Institute of Engineering and Technology Kohinoor, Thenhipalam. P.O.- 673 636, Malappuram, Kerala.
Phone: Principal 0494-2407370, Office 0494–2400223,
Website: www.cuiet.info,E-mail:[email protected]
No.IET/a/Purchase Committee/2011 Dated:30 -01-2013
TENDER NOTICE
Sealed competitive tenders are invited for the supply of item as per the list appended to the
various Departments of Calicut University Institute of Engineering and Technology.
Tender forms can be downloaded from the University website www.universityofcalicut.info or
College website www.cuiet.info and a separate DD for Rs.420/- drawn in favour of the Finance
Officer, University of Calicut should be enclosed with the Tender towards cost of tender form
EMD: 1% of the quoted amount in favor of Finance Officer, University of Calicut.
The material should be supplied at IET, Kohinoor within 15 days from the date of receipt of
supply orders.
The rates quoted should be inclusive of all taxes, installation charges, service guaranty of a
minimum of one year and transportation etc.
Sealed and superscribed tenders should reach the undersigned on or before 20-02-2013,4PM.
PRINCIPAL
DEPARTMENT : ELECTRICAL & ELECTRONICS ENGINEERING
Sl.
No
.
Description of
items required
Specification No. of
units
required
1
Aluminum
Alloy Brake
Drum
(Figure with dimensions attached)
5
2
Fabrication
and fixing the
braking
system
including cost
of all
materials
complete
(For
dimension,
collect details
from lab)
2
3 CRO 25 MHz. 2 Channel, 4 trace
Note: Demonstration if necessary
2
4
Dual
Channel
Digital
Power
Scope
Active differential amplifiers at the inputs (DC-20MHz bandwidth)
Selectable gain 10,100.
Differential isolated measurements with storage facility.
Working voltages - 450V peak (Differential), 700V peak(common
mode)
Easy-to-read TFT LCD display
Dual channel, bandwidth: 25MHz,
Sample rate (real-time) 500MS/s
Equivalent sampling up to 50GS/s
Advanced triggering on edge, video, pulse
20 automatic measurements, manual cursor measurement
rise time 8.8nsec to 14nsec.
Sweep time: 20nsec/50s(25MHz)
10 waveforms, 10 setups storage
+, -, x, ÷, mathematic functions
Zoom with delay scan
Built-in FFT
Built-in USB device, RS232 interface for PC
Automatic calibration
Exclusive digital filter, waveform recorder & pass/fail feature
Frequency counter
Record length 4K each channel
USB host to store waveform on USB drive (pen drive)Note:
demonstration necessary
4
5
Signal
Generator
2 MHz, microcontroller based function generator
Note: demonstration necessary
2
6 Watt meter
72.5/125/250V,5/10A,UPF 4
7 Ammeter (0-0.5)A.MI 4
8 Auto
Transformer
1 Phase,(230/0-270)V,16A 2
9 Auto
Transformer
3 Phase,(415/0-470)V.20A 2
10 D.C Source
(10-300V),3A 2
11
Automatic
variable
frequency AC
drive
AC drive i/p frequency 3 50/60 hz ± 10% i/p pf 0.95 o/p voltage
300-500 V, o/p frequency 3 0.5 Hz-120 Hz. VFD capacity 0-10 HP,
efficiency ≥96%
1
12 Computer
Table &
Chairs
Detailed drawing given below for installing computer tables (Fixed
wooden tables) and revolving chairs
DEPARTMENT: MECHANICAL ENGINEERING
Sl No. Item Specifications Quantity
1 Universal Testing Machine
60T, with graph plotter, extensometer
and other accessories
Demonstration required
1 No.
2 Compression testing machine
1000kN capacity with computer
interface.
Demonstration required
1 No
Mechanical workshop tools
1 Flat file
12” rough cut 15
12” smooth cut 15
12” second cut 15
2 Hand file
10” rough cut 12
10” smooth cut 12
10” second cut 12
3 Flat file 6” rough cut 12
6” smooth cut 12
4 Hand file 6” rough cut 12
6” smooth cut 12
5 Triangular File 10” rough cut 12
10” smooth cut 12
6 Half round file 10” rough cut 12
10” smooth cut 12
7 Bench vice
8” No.8 24
8 Hacksaw frame
12” fixed 25
9 Cold chisel
6” X ¾” 12
10 Engineering Scribers
6” 25
11 Centre punch
4” 12
12 HSS Drill bit
1 to 13 mm 2 sets
13 Steel rule
300 mm, SS 36
14 Engineers Square
200 mm 36
15 Cross peen hammer
500gm, 12
16 Setting hammer
500gm, 12
17 Raising hammer
500gm, 12
18 Riveting hammer 500gm, 12
19
Straight snip
200 mm, HSS 12
20 Tap and die set 5 to 14 mm with wrench, handle and
box 1 set
20 Tap and die set 5 to 14 mm with wrench, handle and
box 1 set
21 Bent snip 200 mm, HSS 12
22 Adjustable spring divider 6” 12
23 Hand groove
Std size 6
24 Carpentry vice
8” 12
25 Pincer
Std size 6
26 Bevel square
Std size 6
27 MITRE square
Std size 6
28 Auger bits
8 to 25 mm 1 set
29 Gimlet 3 to 12 mm 1 set
30 Marking gauge
Std size 12
31 Mortise gauge
Std size 12
32 Wooden jack plane
300 mm 12
33 Wooden smoothening plane
150 mm 12
34 Round nose tongs
400 mm 12
35 Square nose tongs
400 mm 12
36 Pick up tongs
400 mm 12
37 Flatter
moulded 12
38 Electric forge Single phase
Demonstration required 1 no.
39 Welding set
3 phases, Air cooled, movable type,
with face shield, holders, wire brush,
gloves, chipping hammer, cables etc.
1 no
40
Circular saw
8”
1 No.
41 Involute Gear cutter
1.5 Module, 1” bore, No.4 Cutter 2 Nos.
42 Power Hacksaw blade
400 X 32 X 1.6 mm, 10TPI 6 no
43 knurling tool
Multiple adjustable head type 6 Nos.
44 Spanner
26 mm, single end 6 Nos.
45 Thread gauge
BSW 1 No.
46 Bench vice
150 mm, steel 6 Nos.
47 Stop watch
Digital type 10 Nos.
48 Stop watch
Mechanical type 4 Nos.
50 Vernier caliper
600 mm
6 Nos.
51 Tachometer
Digital, contact type
4 Nos.
52 Furniture Requirement for cad
cam lab
Detailed drawing attached for
installing computer tables (Fixed
wooden tables) and revolving chairs
in Cad Cam lab.
Department: PRINTING TECHNOLOGY
Department: Information Technology
Sl. No. Description of items
required
Specification No. of units required
1
Spectrophotometer
.
Range: 190-1100 nm, USB Interface,
Double beam optics, Microprocessor
or computer control
1
2.
Densitometer Density range- .001D to 2.5D with
calibration standard, USB interface
1
3.
Colorimeter Silicon photo diode, interchangeable
glass filter, 400-800nm wavelength
1
4.
5. Color Printer Four color-inkjet , 4800DPI 1
6. Calibration Software Software for calibrating
Monitor, Separate
Scanner
and Printer
(Multiuser)
1
7. Offset Machine Double color unit, Demy size, Sheet-
fed Offset machine
1
Sl.
No.
Description of items required Specification No. of units
required
1
Pen drive
8GB 3
2 Crimping Tool Multipurpose 2
3 SATA Cable 300-600mbps, 30VOLT
10
Department: ELECTRONICS & COMMUNICATION
Sl.
No.
Description of items
required
Specification No. of units
required
1 Digtal Multimeter
Display: 1999 counts
Automatic indication of functions and symbols
DC voltage: 200m/2V/20V/200V±0.5%,
1000V±0.8%
AC voltage: 2V/20V/200V±0.8%, 750V±1.2%
DC current: 20mA±0.8%, 200mA±1.5%,
10A±2.0%
AC current: 2mA±1.0%, 200mA±1.8%,
10A±3.0%
Resistance: 200/2k/20k/200k/2M
Capacitance: 20n/200n/2µ/20µF±4.0%
Frequency: 20kHz±1.5%
Temperature: -20°C ~ 1000°C
3
2 Functional generator sFrequency Range 0.1 Hz to 1 MHz
Operating Modes : Sine, Square, Triangle and
DC
20Vpp Signal Output
LCD for Frequency
Low Distortion
TTL Output
3
3 Arbitrary
Waveform/Function
Generator 25MHz
DDS technology, dual-channel output. Outputs
are totally independent with adjustable phase
shift.
125MSa/s sample rate, 14bit vertical
resolution.
5 types of standard output waveforms, built-in
48 arbitrary waveforms.
Complete set of modulation functions: AM,
FM, PM, FSK, ASK, PWM, linear/logarithmic
sweep, burst.
Abundant input/output: waveform output, ‹
Synchronous signal output, External
modulation source input, 10MHz clock input,
external trigger input, internal trigger output
etc.
Channel coupling and duplication function
Built-in accurate freq. counter allows the user
to measure frequencies up to 200MHz (single
channel)
Standard interfaces: USB Device, USB Host,
1
4 Triple Power Supply 0-30V 0-3A x 2, 5v fixed x 1Triple Output DC
Bench Power Supply
Output Voltage:2 x 0-30VDC
Output Current:0-3A
One +5VDC @ 3A fixed output
Parallel Mode: 0-30Volts; 0-6Amps
Series Mode: 0-60Volts; 0-3Amps
Source Effect: 5x10-4= 2mV
2
Load Effect: 5x10-4= 2mV
Ripple coefficient: <250uV
SMD adhesive sheet element technology for
internal pcb construction
5 Universal IC Tester Test by : Truth table/sequence table
comparison
ZIF : 40 pin DIP ZIF sockets
Keys : 28 cherry keys Key pad with numerical
& functional keys
Display : 9 Digit Seven Segment Display
Supply Input Voltage : 230V AC
1
6 15 MHz
Oscilloscope
15 MHz Bandwidth
Component and Continuity Tester
Sweep Speed 200 ns
Stable Triggering upto 30 MHZ
Digital Readout with Backlit LCD
USB Interface & PC Software (Optional)
Sharp Trace CRT & Auto Focus
2
7 30 MHz Analog
Oscilloscope
2 Channel, Dual-Trace
5 mV - 5 V/div, (1 mV/div with x5 MAG.)
AUTO/NORM Triggered Sweep Operation
X-Y Operation
TV -H and TV-V Triggering
Calibrated 19-Step Time Base with x10 MAG.
Delayed sweep
Built-in component tester for capacitors,
inductors, diodes, transistors, zener diodes
Compact low profile design
3
8 Digital/Analog
Trainer (Basic Unit
Data switches, eight DPDT, Hi 5V, low 0V
• Logic switches, two no bounce with
complimentary out
“On” voltage level 2.8V min., “Off” voltage
level 1V max.
Input impedance 100kÙ
• Eight LED readouts, 100kÙ input impedance
• Clock frequency, 1Hz to 100kHz in 5 steps
continuously variable
• Clock amplitude, 5Vpp squarewave
5
10 Variable Adjustable
30V 5A DC Power
Supply
Adjustable Output Voltage : 0- 30V @ 5A
Output Current : 0-5A
Input Voltage: 220V/50Hz
2nos Bigger size Seven Segment
LED Displays ( Voltage & Current)
Constant voltage/ Constant Current Regulated
Voltage and Current adjustment
Voltage and Current Fine adjustment
Line regulation: CV <= 0.01% + 1 mV
CC <= 0.2% + 1 mA
Load Regulation: CV <= 0.01% + 3mV
CC <= 0.2% + 3 mA
Ripple noise: CV <= 0.5 mV RMS
CC <= 3 mA RMS
2
RESISTORS-Carbon coposition type
SL NO PARTICULARS Qty
SL
NO PARTICULARS Qty
1 1 ohm 50 43 39 K 50
2 22 ohm 50 44 47 K 50
3 47 ohm 50 45 51 K 50
4 100 ohm 50 46 56 K 50
5 120 ohm 50 47 62 K 50
6 150 ohm 50 48 68 K 50
7 180 ohm 50 49 75 K 50
8 220 ohm 50 50 82 K 50
9 270 ohm 50 51 100 K 50
10 330 ohm 50 52 120 K 50
11 360 ohm 50 53 150 K 50
12 390 ohm 50 54 180 K 50
13 470 ohm 50 55 220 K 50
14 560 ohm 50 56 240 K 50
15 620 ohm 50 57 270 K 50
16 680 ohm 50 58 330 K 50
17 750 ohm 50 59 360 K 50
18 820 ohm 50 60 390 K 50
19 1 K 50 61 470 K 50
20 1.2 K 50 62 560 K 50
21 1.5 K 50 63 620 K 50
22 1.8 K 50 64 680 K 50
23 2.2 K 50 65 750 K 50
24 2.4 K 50 66 820 K 50
25 2.7 K 50 67 1 M 50
26 3.3 K 50 68 1.2 M 50
27 3.6 K 50 69 1.5 M 50
28 3.9 K 50 70 1.8 M 50
29 4.7 K 50 71 2.2 M 50
30 5.6 K 50 72 2.4 M 50
31 6.2 K 50 73 2.7 M 50
32 6.8 K 50 74 3.3 M 50
33 7.5 K 50 75 3.6 M 50
34 8.2 K 50 76 3.9 M 50
35 10 K 50 77 4.7 M 50
36 12 K 50 78 5.1 M 50
37 15 K 50 79 5.6 M 50
38 22 K 50 80 6.2 M 50
39 24 K 50 81 6.8 M 50
40 27 K 50 82 7.5 M 50
41 33 K 50 83 8.2 M 50
42 36 K 50 84 10 M 50
Total Quantity 84*50=4200
POTENTIOMETERS-single turn, rotary type(volume control type)
SL NO particulars
Qty
SL
NO particulars
Qty
1 1 K 50 4 22 K 25
2 4.7 K 25 5 47 K 25
3 10 K 25 6 100 K 25
Total 175
CAPACITORS
Electrolytic Type
Ceramic Type
SL NO Particular Qty
SL
NO Particular Qty
1 1uf/50V 25 1 0.1uf 50
2 2.2uf/50V 25 2 0.01uf 50
3 4.7uf/50V 25 3 0.001uf 50
4 10uf/50V 25 4 220uf 50
5 22uf/50V 25 Total 200
6 47uf/50V 25
7 100uf/50V 25
8 220uf/50V 25
9 470uf/50V 25
10 1000uf/50V 25
Total 250
INDUCTORS
SL NO Particular Qty
1 IFT 25
2 RFC 25
3 AFC 25
TRANSFORMER
SL NO Particular Qty
1 6-0-6 25
2 12-0-12 10
DIODE
SL NO Particular Qty
1 IN 4007 100
2 OA 79 25
3 DR 25 25
ZENER DIODE
SL NO Particular Qty 1 3.3V 25
2 5.6V 25
3 6.2V 25
4 9.1V 50
TRANSISTORS SL NO Particular Qty
1 BC547 50
2 BC107 50
3 SL.100 50
4 SK100 50
5 BF494 50
6 FET BFW10 50
7 UJT 2N2646 50
IC'S -AnalogIC'S/Digtal IC'S
SL NO. Particular Qty
1 NE 555 50
2 UA 741 100
3 LM 324 15
4 LM 311 10
5 NE 566 20
6 NE 565 20
7 LM 723 25
8 7400 25
9 7410 25
10 7483 25
11 7486 25
12 7493 25
13 7474 25
14 7495 25
15 7442 25
16 7476 25
17 7404 25
18 7408 25
19 7420 25
20 7421 25
21 7473 25
22 7432 25
23 CD 4016 25
SL NO Particular Qty
1 Bread board 20
2 Digital multiprobe 16
3 Wire strippers 10
4 Tweezer 6
5 IC Plucker 10
6 CRO Probe 10
Colour Qty
Connecting
wire
(Single
strand)
Red 6
Black 2 Green 6
White 2
Grey 2
Blue 6
Yellow 2
Connecting
wire
(1.00
mm2)
Red(METERS) 10
Black(METERS) 10
Part number Description Qty
VLSI KIT Xilinx-System Edition ver. 14.1 or
Latest (50 User License) 1
Spartan 3E Starter Kit-Digilent 5
*** Vmod CAM to be used with Atlys,Geneys kits for
Image Processing experiments
DEPARTMENT: SCIENCE & HUMANITIES( FOR PHYSICS LAB)
Sl.No ITEM DESCRIPTION SPECIFICATION No. OF Units
1 Newton’s ring apparatus with
sodium vapour lamp
Microscope, lens, reflector,ut
condenser,
sodium vapour lamp 55 watt,
transformer deluxe wooden box
1
2 Solar cell characteristics Solar cell mounted in box and
provided with stand for height
adjustment, light source
provided with iris diaphgram ,
main unit provided with 2
meters for taking voltage and
current.
1
3 Spectrometer (scale div. 9 vernier
to 30sec)
Telescope tube: 185mm. focal
length of achromatic length :
175mm, source mercury, prism,
RI:1.51, model:NV656
1
4 Plane transmission grating 600 lines/mm, Size
50mmX35mm,7500 L.P.I
1
5 Plane transmission grating 300 lines/mm, Size
50mmX35mm,7500 L.P.I
1
6 Mercury vapour lamp Box with choke & enclosure
125watt
2
7 Ultrasonic diffraction unit Quartz crystal with tank and
holder, r.f. oscillator, special
type high resolving
spectrometer withy micrometer
scale fitted to eye-piece.
1
8 Tuning fork Electrical (Melde’s apparatus) 1
9 Table lamp Ordinary type 5
10 Travelling microscope (T shape), milky cenolite sheet
on the base.
1
11 Solar cell (characteristics to draw V
& I)
Solar cell mounted in box and
provided with stand for height
adjustment, light source
provided with iris diaphgram ,
main unit provided with 2
meters for taking voltage and
current.
1
12 Transistor characteristics apparatus pnp & npn transistor in
common emitter / base mode.
Features: 1) 2 built-in
continuously variable power
supplies 2) 4 MO65 type round
meters are provided to monitor
voltage and current. 3) Rugged
construction compact unit
provided with self explanatory
users mauel.
1
13 Holding convex lens Magnifying glass 50 mm
diameters.
2
14 Zener diode characteristics
apparatus
Zener diode kit including
voltmeter and ammeter, zener
diode & Power supply
1
15 Sodium vapour lamp with choke & enclosure (85
watt)
1
16 Sodium vapour lamp Low pressure with clamp to
hold it & standard output power
170 watt)
1
17 Characteristics of photo diode 0-3V regulated power supply,
0-2mA digital dc
current meter, 0-20V digital dc
volt meter, white light LED
module, and photo diode LED
type
1
18 LED characteristics apparatus Light emitting diode kit
including voltmeter and
ammeter, LED & Power supply
1
19 Calcite prism 25mmX25mm parallel to base 1
Department: Physical Education
Sl.
No.
Description of items required Specification No. of units
required
1 Shuttle Racket Yonex-MP3, Light weight(83-
100gm)
2
2 Cricket Bat SG RSD Select(English
Willow)
1
3 Batting Pad B.D.M Lightweight 1 set
4 Weighing Machine Metal, Analog 1
5 Stadio Meter Metal, Standard quality 1
6 Whisle Fox 40 Classic 2
7 Stop Watch Digital (10 Lap scoring
Capacity)
1
8 Carrom Board with coins Standard quality-Wooden
33”X33”
2
9 Basket ball Nivia-Synthetic leather 3
10 Foot ball Nivia-Classic,Synthetic leather 4
11 Practice Cone Vinex (9 inch) Plastic 20`
12 Practice Shade Vinex. Plastic 20
13 Wibs Rice knit cloth, Orange colour 12